Text preview for : Infinity-PS210 actsub.pdf part of Infinity PS210 active subwoofer
Back to : Infinity-PS210 actsub.pdf | Home
PS Series
PS210 Subwoofer
SERVICE MANUAL
Infinity Systems, Inc. 250 Crossways Park Dr. Woodbury, New York 11797 Rev1 8/2007
PS series PS210 subwoofer
- CONTENTS -
BASIC SPECIFICATIONS
........................................1
DETAILED SPECIFICATIONS......................................2 PACKAGING.............................................................4 CONTROLS AND CONNECTIONS................................5 OPERATION.............................................................7 EXPLODED VIEW/PARTS LIST .................................8
TEST SET UP AND PROCEDURE.................................9 BLOCK DIAGRAM.....................................................10 ELECTRICAL PARTS LIST (120v) ...............................11 PCB DRAWINGS......................................................14 SEMICONDUCTOR PINOUTS.....................................16 SCHEMATICS (120v)................................................17
Basic Specifications PS210 Powered Subwoofer
Frequency Response: Maximum Amplifier Output: 27Hz 150Hz (±3dB) 300 Watts RMS; 500 Watts Peak (20Hz 150Hz with no more than 0.1% THD) 50Hz 150Hz, 24dB/octave, continuously variable 10" (254mm) MMD® 15-3/4" x 12-1/2" x 16-1/2" (400mm x 318mm x 419mm) 38.6 lb (17.6kg)
Crossover Frequencies: Driver: Dimensions (H x W x D): (with grille) Weight:
Infinity continually strives to update and improve existing products, as well as create new ones. The specifications and construction details in this and related Infinity publications are therefore subject to change without notice.
1
PS series PS210 subwoofer
Primus PS210
LINE VOLTAGE US 120vac/60Hz EU 230vac/50-60Hz Parameter Amp Section Type (Class AB, D, other) Load Impedance (speaker) Rated Output Power (120VAC) Rated Output Power (230VAC) AVG RMS Dynamic Power THD @ Rated Power THD @ 1 Watt DC Offset Damping factor Input Sensitivity-120V Input Frequency L&R LFE input System Gain Input Sensitivity-230V Input Frequency L&R LFE input System Gain Signal to Noise SNR-A-Weighted SNR-unweighted SNR rel. 1W-unweighted Residual Noise Floor
150W Powered Sub Amp
Yes/No Yes Yes Specification D 4 150 150 210 0.5 0.2 10 >50 Hi/Lo Line 108-132 207-253 Unit n/a Ohms Watts Watts Watts % % mV-DC DF Nom. 120 230 QA Test Limits n/a n/a 145 Unit Vrms Vrms Conditions Notes Normal Operation Normal operation, MOMS required Notes
Nominal Domestic version only 120 VAC-60 Hz EU Version only 230 VAC-50-60 Hz Average RMS power, 3/20 Cycles 50 Hz, Driven 6dB above its input sensitivity sensitivity, average of the first 4 consecutive peaks 22K filter 22K filter Sub amp output Measured at amplifier board Measured at the speaker cable. 150 Watts @ THD < 0.1 % @ 50 Hz
200 1 0.3 30 35
50 9.5 9.5 46.72
Hz mVrms mVrms dB
50 Nominal Freq. ±1dB To 1 Watt ±1dB To 1 Watt Reference
Single input driven Single input driven, LFE switch ON Single input driven Normal mode
50 TBD TBD TBD
Hz mVrms mVrms dB
50 Nominal Freq. ±1dB To 1 Watt ±1dB To 1 Watt Reference
Single input driven Single input driven, LFE switch ON Single input driven Normal mode
90 80 -57 1.5
dBA dBr dBr mVrms(max)
85 75 -55 2.5
relative to rated power relative to rated power relative to 1W Output Volume @max, w/ A/P Swept Bandpass Measurement (Line freq.+ harmonics) (BW=20 KHz)
A-Weighting filter 22K filter 22K filter Line level inputs must be terminated using 1KOHM
Input Impedance Line Input (L, R,LFE) Filters LP filter Variable Subsonic filter (HPF) 2rd Order Friend circuit LFE Low pass Limiter THD at Max. Output Power Features Volume pot Taper (lin/log) Phase switch LP Filter defeat switch Input Configuration Line In (L,R) & LFE Signal Sensing (ATO) Auto-Turn-On (yes/no) ATO Input test frequency ATO Level LFE Input ATO Turn-on time Auto Mute/ Turn-OFF Time Power on Delay time Transients/Pops ATO Transient Turn-on Transient
10K
ohms
n/a
Nominal
50-150 Fixed Fixed 200>LP<500
Hz
± 10
2nd order variable + 2nd order fix-24 db/Octave 12dB/Octave F=31Hz, Q=2 60Hz, Q=2, Av=-3.9dB
Hz
LFE input driven only
N/A -LOG 0-180 YES
N/A
functional Maximum Output Power
Maximum THD as a result of limiting.
-deg
functional functional functional
A Taper Disables LP filter, intended for LFE
YES
--
functional
Dual RCA jack
YES 50 2.5 5 5-15 3
Hz mV ms minutes sec.
functional functional functional Amp connected and AC on, then functional input signal applied T before muting, after signal is 5-15 removed 4 AC Power Applied
Maximum acceptable level.
Auto turn of time (T) must be 5 > T < 15 Minutes
0.5 0.5
V-peak V-peak
0.5V 0.8V
@ Sub amp output @ Sub amp output
Amplifier activated by signal presence at the Line input AC Line cycled from OFF to ON
2
PS series PS210 subwoofer
Parameter Turn-off Transient Efficiency Efficiency Efficiency at 1/8 of rated power Off state input power Stand-by Input Power Power Cons. @ rated power Protections Short Circuit Protection YES Amplifier should resume operation after short circuit condition removal Temperature rise in accessible metal parts @1/8 max unclipped Power at 1.06 should not exceed 35K rise for domestic version functional times the input voltage or 30K rise for European versions (refer to requirements sheet). Design must insure no Offset at the speaker DC present at Speaker Out leads output under any operating condition including abnormal operation functional Direct short at output Amps Amps 2 1.25 Type-T or Slo Blo-250 V Type-T or Slo Blo-250 V, Low Breaking capacity Internal fuse with UL/SEMKO rated holder Internal fuse with UL/SEMKO rated holder Specification 0.5 Unit V-peak QA Test Limits 0.8V Conditions @ Sub amp output Notes AC Line cycled from ON to OFF
60 38 16 24 250
% % Watts Watts Watts
58 37 18 26 260
Test conducted at rated power 150WNominal Line voltage Test conducted at 18.75 WRMS Nominal Line voltage-Rated impedance 4 Ohms Nominal Line voltage RED LED @ nom. line voltage @ nom. line voltage Maximum allowable input power under nominal Input voltage and frequency, HOT or COLD operation.LED GREEN no signal applied 150 Watts @ 4 Ohms nominal line voltage
Thermal Protection
YES
DC Offset Protection Line Fuse Rating USA-Domestic EU
YES
2 1.25
3
PS series PS210 subwoofer
4
PS series PS210 subwoofer
CONTROLS AND CONNECTIONS
Rear Panel
¡ Subwoofer-Level Control TM LFE/Normal Selector
¶
Green: On Red: Standby
¡
LEVEL
Min Max
£ Phase Switch ¢ Crossover Adjustment
LFE
NORMAL
TM
Line-Level/LFE Input § Power Switch ¶ Status LED
PHASE
0º 80Hz
180º
£
CROSSOVER FREQUENCY
50Hz
¢
150Hz
L
LINE LEVEL IN
R
For LFE use L or R
ON
OFF
§
POWER
120V 60Hz
CAUTION
RISK OF ELECTRIC SHOCK DO NOT OPEN
WARNING:
TO REDUCE THE RISK OF FIRE OR ELECTRICAL SHOCK DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE.
NRTL/C CSA 22.2 UL1492
AVERTISSEMENT:
POUR PRÉVENIR LES RISQUES D'INCENDIE OU DE CHOC ÉLECTRIQUE, ÉVITER D'EXPOSER CET APPAREIL A LA PLUIE OU A L'HUMIDITÉ.
PS210 (120V)
5
PS series PS210 subwoofer
SYSTEM CONNECTIONS
If you have a Dolby® Digital or DTS® receiver/processor with a low-frequency effects (LFE) or subwoofer output:
SUBWOOFER OR LFE OUTPUT
LEVEL
Green: On Red: Standby
Min
Max
LFE
NORMAL
Set LFE/Normal switch to "LFE."
CROSSOVER FREQUENCY
PHASE
0º 80Hz
180º
50Hz
150Hz
L
LINE LEVEL IN
R
For LFE use L or R
If your receiver/processor does not contain a Dolby Digital or DTS processor but has subwoofer outputs:
LEVEL
Green: On Red: Standby
Min
Max
LFE
NORMAL
PHASE
0º 80Hz
180º
L
R
CROSSOVER FREQUENCY
50Hz 150Hz
L
R
Set line-level/LFE switch to "Normal." NOTE: If your receiver/processor has only one sub out, you may use either the L or R input.
LINE LEVEL IN
For LFE use L or R
6
PS series PS210 subwoofer
OPERATION
Power On
Plug your subwoofer's AC cord into a wall outlet. Do not use the outlets on the back of the receiver. Initially set the Subwoofer-Level Control ¡ to the "min" position. Turn on your sub by pressing the Power Switch § on the rear panel.Turn on your entire audio system and start a CD or movie soundtrack at a moderate level.
Crossover Adjustment
The Crossover Adjustment Control ¢ determines the highest frequency at which the subwoofer reproduces sounds. If your main speakers can comfortably reproduce some low-frequency sounds, set this control to a lower frequency setting, between 50Hz and 100Hz.This will concentrate the subwoofer's efforts on the ultradeep bass sounds required by today's films and music. If you are using smaller bookshelf speakers that do not extend to the lower bass frequencies, set the Crossover Adjustment control to a higher setting, between 120Hz and 150Hz. NOTE: This control will have no effect if the LFE/Normal Selector TM is set to LFE. If you have a Dolby Digital or DTS processor/receiver, the Low-Pass Frequency is set by the processor/receiver. Consult your owner's manual to learn how to view or change this setting.
Auto On/Standby
With the Power Switch § in the ON position, the Status LED ¶ on the back panel will remain lit in red or green to indicate the On/Standby mode of the subwoofer. RED = STANDBY (No signal detected, Amp Off) GREEN = ON (Signal detected, Amp On) The subwoofer will automatically enter the Standby mode after approximately 10 minutes when no signal is detected from your system.The subwoofer will then power ON instantly when a signal is detected. During periods of normal use, the Power Switch § can be left on.You may turn off the Power Switch § for extended periods of nonoperation, e.g., when you are away on vacation.
MAINTENANCE AND SERVICE
The enclosure may be cleaned using a soft cloth to remove fingerprints or to wipe off dust. The grille may be gently vacuumed. Stains may be removed with an aerosol cleaner, following its instructions. Do not use any solvents on the grille. All wiring connections should be inspected and cleaned or remade periodically.The frequency of maintenance depends on the metals involved in the connections, atmospheric conditions, and other factors, but once per year is the minimum. In the event that your subwoofer ever needs service, contact your local Infinity dealer or distributor, or visit www.infinitysystems.com for a service center near you.
Adjust Gain
Turn your Subwoofer-Level Control ¡ up to the halfway position. If no sound emanates from the subwoofer, check the AC-line cord and input cables. Are the connectors on the cables making proper contact? Is the AC plug connected to a "live" receptacle? Has the Power Switch § been pressed to the "On" position? Once you have confirmed that the subwoofer is active, proceed by playing a CD, record or cassette. Use a selection that has ample bass information. Set the overall volume control of the preamplifier or stereo to a comfortable level. Adjust the Subwoofer-Level Control ¡ until you obtain a pleasing blend of bass. Bass response should not overpower the room but rather be adjusted so there is a harmonious blend across the entire musical range. Many users have a tendency to set the subwoofer volume too loud, adhering to the belief that a subwoofer is there to produce lots of bass.This is not entirely true. A subwoofer is there to enhance bass, extending the response of the entire system so the bass can be felt as well as heard. However, overall balance must be maintained or the music will not sound natural. An experienced listener will set the volume of the subwoofer so its impact on bass response is always there but is never obtrusive.
Phase Control
The Phase Switch £ determines whether the subwoofer speaker's piston-like action moves in and out with the main speakers, 0°, or opposite the main speakers, 180°. Proper phase adjustment depends on several variables such as room size, subwoofer placement and listener position. Adjust the phase switch to maximize bass output at the listening position.
7
PS series PS210 subwoofer
8
PS series PS210 subwoofer
PS210 sub Test Set Up and Procedure
SYSTEM AURAL SWEEP TEST Equipment needed: · Function/signal generator/sweep generator · Integrated Amplifier · Multimeter · Speaker cables General Unit Function (UUT = Unit Under Test) Switches/knobs on the amplifier faceplate: Crossover Frequency Adjust full CW (Max) Phase switch either position Normal/LFE switch - Normal 1. From the signal generator, Connect both right and left line level inputs (RCA jacks) to signal generator and UUT. Use Y-cable if necessary from mono source. 2. On the amplifier, turn the LEVEL control full Counterclockwise (Min). 3. Turn on generator, adjust to 75mV, 50 Hz. 4. Plug in UUT; turn the power switch ON. Turn LEVEL control full Clockwise (Max). 5. LED (on amp panel) should now be Green; immediate bass response should be heard and felt from rear port tube opening. Sweep Function 1. Follow steps 1-5 above, using a sweep generator as a signal source. 2. Sweep generator from 20Hz to 1kHz. Listen to the cabinet and drivers for any rattles, clicks, buzzes or any other noises. If any unusual noises are heard, remove woofer and test. Driver Function (Woofer) 1. Remove woofer from cabinet; detach + and - wire clips. 2. Check DC resistance of woofer; it should be 3.4 ohms±10%. 3. Connect a pair of speaker cables to driver terminals. Cables should be connected to an integrated amplifier fed by a signal generator. Turn on generator and adjust so that speaker level output is 5.0V. 4. Sweep generator from 20Hz to 1kHz. Listen to driver for any rubbing, buzzing, or other unusual noises.
9
PS series PS210 subwoofer
10
PS series PS210 subwoofer
PS210 Electrical Parts List
Part number Qty Description Reference Designator
PREMAP/MAIN/POWER PCB
Capacitors 034-330525-300ZR 1 GR Electrolytic cap. 33uF/25V M (R)0511 P:5 033-680464-270ZS 1 GS NPE Cap. ELYTONE 6u8/100V K10 (R)1020 GNE 032-100484-200ZS 1 GS END Mylar cap. 1uF/250V K P:15 033-470464-270ZS 1 GS NPE Cap.(ELYTONE)1K 4u7/100V K10 (R)1015 GNE 031-100343-100ZS 1 GS SMD Cap. 100pF/50V J 0805 NPO 034-220525-301ZS 2 GS Electrolytic cap. 22uF/25V M (R)5x11 P:5 031-560243-100ZS 2 GS SMD Cap. 56pF/50V J 0805 NPO 031-220243-103AZ 1 GS SMD Cap. 0u022/50V J 0805 X7R 031-100344-100ZS 17 GS SMD Cap. 0u1/50V K 0805 X7R 031-100244-100ZS 4 GS SMD Ceramic cap. 0u01/50V K 0805 X7R 034-470515-307ZR 1 GR Electrolytic cap.LOW ESR 85 47uF/16V M (R)0511 P:5 031-100344-100ZS 1 GS SMD Cap. 0u1/50V K 0805 X7R 034-100625-300ZS 1 GS Electrolytic cap. 100uF/25V M (R)6.3x11 P:5 031-470244-102ZS 2 GS SMD Cap. 0u047/50V K 0805 X7R 031-560343-102ZS 1 GS SMD Cap. 560pF/50V J 0805 NPO 034-330615-300ZS 1 GS Electrolytic cap. 330uF/16V M (R)0812 P:5 031-100344-100AZ 2 GS SMD Cap. 0u1/50V K 0805 X7R 035-100393-301ZR 2 GR Mylar cap.(ESK TYPE) 0u1/63V J P:5 PN:ESK063S10JT 035-220393-300ZR 1 GR PE Cap. 0u22/63V J P:5 034-470415-301ZS 1 GS Elect. Cap. 4u7/50V M (R)0511 P:5 034-100525-300ZS 3 GS Electrolytic cap. 10uF/25V M (R)0511 P:5 031-100244-100ZS 2 GS SMD Ceramic cap. 0u01/50V K 0805 X7R 031-100343-100ZS 2 GS SMD Cap. 100pF/50V J 0805 NPO 031-100344-100ZS 1 GS SMD Cap. 0u1/50V K 0805 X7R 031-100384-100RZ 2 GS SMD Cap. 0u1/250V K 1206 X7R 031-220243-103AZ 1 GS SMD Cap. 0u022/50V J 0805 X7R 031-220344-100ZS 5 GS SMD Cap. 220pF/50V J 0805 NPO 031-330244-100ZR 1 GR SMD Cap. 0u033/50V K 0805 X7R 031-680444-102ZR 2 GR SMD Cap. 6800pF/50V K X7R 0805 032-270343-301ZS 3 GS Mylar cap. (MP) 0u27/63V J P:5 032-820244-200ZR 1 GR Mylar cap. 0u082/100V K (R) 034-220515-302ZR 2 GR elect. Cap. 22uF/16V M (R)0511 P:5 034-220525-301ZS 4 GS 22uF/25V M (R)5x11 P:5 034-330615-300ZS 1 GS 330uF/16V M (R)0812 P:5 034-330780-300ZR 2 GR 85 SNAPIN 3300uF/80V M (R)22x48 034-470515-200ZR 1 GR 47uF/16V M (R)0511 P:2.5 039-100384-100ZR 1 GR Safety cap. (0u1/250V) .1K275VACx2 18x6x12mm 034-100615-301ZS 1 GS electrolytic cap. 100uF/16V M (R)0611 P:5 031-100344-100ZS 2 GS SMD Capacitor 0u1/50V K 0805 X7R 031-100444-104ZR 1 GR SMD Capacitor 1000pF/50V K 0805 X7R Resistors 024-100398-120ZR 020-220497-120ZR 024-100298-120ZR 021-100401-120ZR 024-470498-120ZR 022-500003-020ZR 024-220798-120ZR 024-430498-120ZR 024-300498-120LZ 024-470598-120ZR 024-220598-120ZR 024-680498-120ZR 024-110598-100ZR 024-200598-120ZR 024-100698-120ZR 1 1 2 1 2 1 1 1 1 1 1 6 1 1 2 GR SMD Resistor 100R 1/8W J 0805 GR Carbon Resistor 2K2 1/4W J GR SMD Resistor 10R 1/8W J 0805 GR MOF Resistor 1K 1W J INK MO-100 GR SMD Resistor 4K7 1/8W J 0805 GR Resistor KNP 0R05 3WS J FK TYPE GR SMD Resistor 2M2 1/8W J 0805 GR SMD 4K3 1/8W J 0805 GR SMD 3K 1/8W J 0805 GR SMD 47K 1/8W J 0805 GR SMD 22K 1/8W J 0805 GR SMD 6K8 1/8W J 0805 GR SMD 11K 1/8W F 0805 GR SMD 20K 1/8W J 0805 GR SMD 100K 1/8W J 0805 R62 R11 R81,82 R103 R85,86 R104 R80 R78 R105, R107 R118, R91 R98 R94 R3,112 R2,74,75,84,88,89,97,106,113-117,119,120, 141,138,139, C1 C72 C70, C73 C58 C50,53 C57,61 C84, C42-44,46-49,52,55,60,63,71,74,77,100,101,80, C45,51,66,67, C65 C54 C64 C62,59 C56 C78 C81,82 C28,2A, C27, C2 C35,237,238, C5,10 C16,36 C11 C3,7 C40 C14,15,20,21,19 C33, C32,34, C29,26,25 C30 C39,75 C4,9,41,76 C12 C6,8 C37 CXAC1 C83 C102,103, C104
024-100598-120ZR 18 GR SMD 10K 1/8W J 0805
11
PS series PS210 subwoofer
Part number Qty Description Reference Designator
PREMAP/MAIN/POWER PCB
024-100498-120ZR 7 GR SMD 1K 1/8W J 0805 024-590498-100ZR 1 GR SMD 5K9 1/8W F 0805 024-270498-120ZR 1 GR SMD 2K7 1/8W J 0805 024-442498-100ZR 1 GR SMD 4K42 1/8W F 0805 024-200498-120ZR 1 GR SMD 2K 1/8W J 0805 024-300598-120ZR 1 GR SMD 30K 1/8W J 0805 024-150598-100ZR 2 GR SMD 15K 1/8W F 0805 024-470698-120ZR 2 GR SMD 470K 1/8W J 0805 024-390598-120ZR 1 GR SMD 39K 1/8W J 0805 024-470298-120ZR 2 GR SMD 47R 1/8W J 0805 024-390498-120ZR 1 GR SMD 3K9 1/8W J 0805 024-220398-120ZR 1 GR SMD 220R 1/8W J 0805 024-470398-120ZR 3 GR SMD 470R 1/8W J 0805 024-330498-100ZR 2 GR SMD 3K3 1/8W F 0805 024-220498-121ZR 2 GR SMD 2K2 1/8W J 0805 024-162598-100ZR 4 GR SMD 16K2 1/8W F 0805 024-000098-120ZR 1 GR SMD Resistor 0R 1/8W J 0805 024-100498-120ZR 3 GR SMD Resistor 1K 1/8W J 0805 024-100598-100ZR 5 GR SMD 10K 1/8W F 0805 024-100598-120ZR 11 GR SMD 10K 1/8W J 0805 024-100898-120ZR 1 GR SMD 10M 1/8W J 0805 024-130498-100ZR 1 GR SMD 1K3 1/8W F 0805 024-150498-120ZR 1 GR SMD 1K5 1/8W J 0805 024-150598-100ZR 3 GR SMD 15K 1/8W F 0805 024-160698-120ZR 1 GR SMD 160K 1/8W J 0805 024-220498-121ZR 2 GR SMD 2K2 1/8W J 0805 024-237598-120ZR 1 GR SMD 23K7 1/8W F 0805 024-243498-100ZR 1 GR SMD 2K43 1/8W F 0805 024-270498-120ZR 1 GR SMD 2K7 1/8W J 0805 024-300598-120ZR 1 GR SMD 30K 1/8W J 0805 024-330498-120ZR 8 GR SMD 3K3 1/8W J 0805 024-330598-120ZR 2 GR SMD 33K 1/8W J 0805 024-332498-100ZR 2 GR SMD 3K32 1/8W F 0805 024-470498-121ZR 3 GR SMD 4K7 1/4W J 1206 024-470598-120ZR 2 GR SMD 47K 1/8W J 0805 024-470698-120ZR 1 GR SMD 470K 1/8W J 0805 024-470798-120ZR 1 GR SMD 4M7 1/8W J 0805 024-475498-100ZR 1 GR SMD 4K75 1/8W F 0805 024-511398-100ZR 1 GR SMD 511R 1/8W F 0805 024-560598-120ZR 1 GR SMD 56K 1/8W J 0805 024-619498-100ZR 2 GR SMD 6K19 1/8W F 0805 024-619598-100ZR 1 GR SMD 61K9 1/8W F 0805 024-620398-100ZR 2 GR SMD 620R 1/8W F 0805 024-680498-120ZR 5 GR SMD 6K8 1/8W J 0805 024-680598-120ZR 1 GR SMD 68K 1/8W J 0805 024-681598-100ZR 2 GR SMD 68K1 1/8W F 0805 024-750398-101ZR 1 GR SMD 750R 1/8W F 0805 TPAING 024-750498-100ZR 1 GR SMD 7K5 1/8W F 0805 024-750598-100ZR 1 GR SMD 75K 1/8W F 0805 024-820598-120ZR 2 GR SMD 82K 1/8W J 0805 026-200595-269ZS 1 GS VR PN:RD163121R03D-20KBx2(EJ) FREQUENCY 026-500495-005ZS 1 GS VR 5K PN:RD163111R22B-5K15A-EJ LEVEL 024-100598-120ZR 2 GR SMD Resistor 10K 1/8W J 0805 024-270598-120ZR 1 GR SMD Resistor 27K 1/8W J 0805 Semiconductors 054-033904-100ZR 054-055500-100ZR 054-033906-100ZR 051-640001-000ZR 054-033904-100ZR 051-222200-100ZR 051-000600-100ZR 1 1 3 2 4 1 1 GR SMD (TRANSISTOR) PN:MMBT3904LT1G SOT23 (O GR SMD IC: PN:NE555DR S08 (TI) TMER GR SMD Transistor (ON) PN:MMBT3906LT1G SOT23 GR MOSFET N-Channel PN:IRF640NPBF TO-220 (IR) GR SMD (TRANSISTOR) PN:MMBT3904LT1G SOT23 (O GR Transistor NPN (ON SEM) PN:MPS2222ARLRAR TO-92 GR Transistor NPN PN:MPSW06RLRA TO-92 (ON) Q28 U10 Q10,12,15 Q18,22 Q11,14,13,27 Q21 Q16 R79,83,92,95,96,110,145, R140, R73 R128 R108 R131, R132,133, R129,130, R77 R101,102 R93 R90 R76,99,100 R127,137, R1,87, R125,126,135,136, R68 R65,44,151, R146,147,30,31,33, R17,19,,54,58,63,71,72,111,123,124,134, R121 R5A R67 R29, R152, R61,57, R48 R36 R64 R56, R7,8,12-15,59,55, R4,5 R26,27 R148-150, R47,49 R70, R60 R38 R6A R122 R51,53 R4A R16,18 R46,40-43 R66, R50,52, R2A R35A R45 R69,39, VR2 VR1 R142,144 R143
12
PS series PS210 subwoofer
Part number Qty Description Reference Designator
PREMAP/MAIN/POWER PCB
054-540100-100ZR 3 GR SMD Transistor PNP (ON SEN) MMBT5401 LT1 SOT-23 051-555100-000ZR 1 GR Transistor NPN PN:2N5551 TO-92 051-290700-100ZR 2 GR Transistor PNP (ON) PN:MPS2907A RLRAR TO-92 051-540101-000ZR 1 GR Transistor PNP(FAIRCHILD PN:2N5401 TO-92 054-414803-100ZS 13 GS SMD DIODE: PN:LL4148 MINI-MELF 054-008409-000ZR 1 GR SMD ZENER DIODE: PN:BZX84C3V0-7-F SOT-23 054-008406-000ZR 1 GR SMD ZENER DIODE:PN:BZX84C10-7-F SOT-23 054-008408-000ZR 2 GR SMD ZENER DIODE: PN:BZX84C5V6-7-F SOT-23 054-000100-100ZR 4 GR GS SMD DIODE: PN:ES1D 200V 1A (PANJIT) 054-007200-100ZR 3 GR SMD IC PN:TL072CDR SO-8 (TI) DUAL OP-AMP 053-211100-000ZR 1 GR IC:DIP,PN:IR2111 8PIN (IR) HALF-BRIDGE DRIVER 051-011100-100ZR 1 GR JFET N-Channel PN:J111 TO-92 (FAIRCHILD 054-000100-100ZR 1 GR GS SMD DIODE: PN:ES1D 200V 1A (PANJIT) 054-007200-100ZR 4 GR SMD IC PN:TL072CDR SO-8 (TI) 054-007400-100ZR 2 GR SMD IC:(OP) PN:TL074CDR (TI) 054-008407-000ZR 3 GR SMD ZENER DIODE: PN:BZX84C15-7-F SOT-23 054-011400-100ZR 1 GR SMD Transistor PN:DTC114TKA SMT3 (ROHM 054-033904-100ZR 4 GR SMD (TRANSISTOR) PN:MMBT3904LT1G SOT23 (O 054-033906-100ZR 1 GR SMD Transistor (ON) PN:MMBT3906LT1G SOT23 054-045580-100ZS 1 GS SMD IC:(OP) PN:NJM4558M-TE3- DUAL OP-AMP 054-414803-100ZS 15 GS SMD DIODE: PN:LL4148 MINI-MELF 054-524201-100ZR 1 GS SMD ZENER DIODE: PN:MMBZ5242B 12V SOT-23 054-540100-100ZR 2 GR SMD Transistor PNP (ON SEN) MMBT5401 LT1 SOT-23 051-024100-000ZR 1 GR Transistor DIP PN:MJE241 TO-126 (CENTRAL) NPN 051-025100-000ZR 1 GR Transistor DIP PN:MJE251 TO-126 (CENTRAL) PNP 052-400080-000ZR 1 GR Bridge Rectifier PN:RS804 400V,8A 051-003100-000ZS 1 GS Transistor NPN PN:TIP 31C TO-220 (MOSPEC) 050-505200-001ZS 1 GS LED PN:LT-2402-21 Q20 Q17 Q19,23 Q1 D1,2,27,31,34,44,40-43,46,47,45, D25 D35 D36,37 D5,26,29,33 U6,8,1, U7 Q200 D38 U5 U2,3 D6,7,9 Q7 Q5,8,25,9 Q6, U4 D3,4,8,30,39,11,14,16,17,20,22,18,19,28,32, D206, Q24,26 Q2 Q3 BR1 Q4
Miscellaneous/Mechanical
025-010300-000ZR 074-300018-000ZR 043-560200-000ZR 043-300101-000ZR 043-700101-000ZR 041-115001-000ZR 044-100100-000ZR 074-020018-000ZR 093-105202-300ZR 093-205001-320ZR 042-010053-003ZR 042-018600-000ZR 061-020000-000ZS 061-314002-000ZS 061-400014-000BZ 061-700044-000ZR 063-010012-000ZR 063-321101-000ZR 063-531808-000ZR 073-011006-400ZR 073-032315-601ZS 082-022607-000BZ 086-021818-005ZR 086-021820-001ZR 043-000051-000ZR 043-324300-000ZR 072-010305-000ZS 072-040169-000ZR 073-050001-000ZS 074-030002-000ZR 072-040720-000ZR 1 1 1 1 1 1 2 1 1 1 1 1 2 2 4 3 4 1 1 1 1 1 1 1 1 1 1 1 2 2 1 GR Thermister PN:NTSE103KZ072 K L:50mm GR RELAY PN:943-1C-48D GR INDUCTOR 56uH YT-10779 GR INDUCTOR PN:YT-10033 30uH GR TOROIDAL INDUCTOR 70uH YT-10682 GR BEAD COIL PN:YT-10911 GR SMD FERRITE BEAD PN:321611 600R/100MHz 1206 GR ROCKER SW (POWER) PN:RF1003-BB4-0 GR FUSE:UL GSL(2AG) FUSE:2A,250V,5*20mm 120V GR FUSE: VBS UTE1.25A,250V,5*20mm 230V GR Transformer YT-10616-4 for 120V GR Transformer YT-10913 for 230V GS Knob ABS HTS-10/20 20x15m/m UL94V-0 BLK GS Strain Relief PN:SB4F-2 GR RUBBER FOOT ID:6.2 OD:11.5 t:2mm 55 BLK GR Mica 13x18mm TO-220 GR Bracket for Transistor P/N:TRK-1 GR Panel 322x105.7x15mm BLK ABS-94V0 GR bucket (PB-10/12) ABS 322x105.7x146.5mm BLK (94VO) GR BRACKET 16x34mm t:0.8mm GS Heatsink black anodized 70x58x20mm GR Wire set #26 UL1007 L:74mm 2P HOUSING GR Power Cord NISPT-2 18AWGx2 L:1830mm 105C+T187 GRPower cord L:2.0M H05VV-F2x0.75WS019+002E for 230V GR COIL PN:YT-53015 GR INDUCTOR 324uH YT-10778 GS RCA JACK PN:B217BK 2P INPUT GR CONNECTOR PN:JS-1001-2 2P P:2.5mm GS FUSE CLIP P/N:CT-FH1206 GR TOGGLE SW PN:L101-T2B4QE LFE, PHASE GR HEADER Right Angle PN:JS-1109R-04(S1) TH1, K1 L1 L2 L3 L5 FB1,FB2 F1 (120V) F1 (230V) (120V) (230V) LEVEL, FREQUENCY for Transformer
PCB CON3B1, (120V) (230V) L6 L4 CONN1 CON3A1 SW5,SW6
13
CAM350 V 8.0.6 : Thu Mar 08 13:50:59 2007 - (Untitled)
PS series PS210 subwoofer
14
CAM350 V 8.0.6 : Thu Mar 08 13:47:26 2007 - (Untitled)
PS series PS210 subwoofer
15
PS series PS210 subwoofer
16
PS series PS210 subwoofer
3 2
01 02
New design
17
1
PS series PS210 subwoofer
01 02
New design
18