Text preview for : Infinity-PS212W wirelessactsub.pdf part of Infinity PS212W wireless active subwoofer
Back to : Infinity-PS212W wirelessa | Home
Wireless Powered Subwoofer
PS212W
Service Manual
Infinity Systems, Inc. 250 Crossways Park Dr. Released 2008 Discontinued XXXX Woodbury, New York 11797 Rev0 8/2008
PS212W subwoofer
- CONTENTS BASIC SPECIFICATIONS ......................................1 DETAILED SPECIFICATIONS ................................2 PACKAGING........................................................4 CONTROLS/CONNECTIONS..................................5 OPERATION ........................................................7 SUBWOOFER EXPLODED VIEW/PARTS LIST..........8 TRANSMITTER EXPLODED VIEW/PARTS LIST........9 TEST SET-UP AND PROCEDURE..........................10 AMPLIFIER BLOCK DIAGRAM...............................12 SUBWOOFER AMP TROUBLESHOOTING........ ......13 TRANSMITTER TROUBLESHOOTING....... .............14 RECEIVER PCB TROUBLESHOOTING............. ......15 P.C.B. DRAWINGS...............................................16 ELECTRICAL PARTS LIST ...................................23 IC/TRANSISTOR PINOUTS.....................................29 SCHEMATICS....................................................43
Basic Specifications Infinity PS212W
Frequency Response: 25Hz 150Hz (3dB) Amplifier RMS Power: 400 Watts Amplifier Peak Power *: 700 Watts Crossover Frequencies: 50Hz 150Hz, continuously adjustable when activated Driver: 12" (305mm) MMD® RF Operating Frequency: 2.4GHz Operating Range: Up to 75' (23m), depending upon conditions Subwoofer Dimensions (H x W x D): 18" x 14-3/8" x 18-3/4" (457mm x 365mm x 476mm) Subwoofer Weight: 44.7 lb (20.3kg) Transmitter Dimensions: 1-1/8" x 4-7/8" x 3-7/8" (29mm x 124mm x 98mm) Transmitter Weight: 0.5 lb (0.2kg)
Infinity continually strives to update and improve existing products, as well as create new ones. The specifications and construction details in this and related Infinity publications are therefore subject to change without notice. * The peak dynamic power is measured by recording the highest center-to-peak voltage measured across the output of a resistive load equal to minimum impedance of the transducer, using a 50Hz sine wave burst, 3 cycles on, 17 cycles off.
1
PS212W subwoofer
PS212W
LINE VOLTAGE US 120vac/60Hz EU 230vac/50-60Hz Parameter Amp Section Type (Class AB, D, other) Load Impedance (speaker) AVG System impedance Min System imepdance Rated Output Power (120VAC) AVG RMS Dynamic Power THD @ Rated Power THD @ 1 Watt DC Offset Damping factor Input Sensitivity Input Frequency L or R LFE input System Gain (L or R inputs) System Gain (LFE input) Signal to Noise SNR-A-Weighted SNR-unweighted Residual Noise Floor
250W Powered Sub Amp
Yes/No Yes Yes Specification D 4 5.482 3.688 250 300 0.5 0.2 10 >50 Hi/Lo Line 108-132 207-253 Unit n/a Ohms Ohms Ohms Watts 320 % % mV-DC DF Nom. 120 230 QA Test Limits n/a n/a n/a n/a 250 Reference 1 0.3 30 20 Unit Vrms Vrms Conditions Notes Normal Operation Normal operation, MOMS required Notes
Nominal AP Computed BW from 20 to 500Hz @ 26Hz Domestic version only 120 VAC-60 Hz 200mV driven into LFE input Average RMS power, 3/20 Cycles 50 Hz, Driven 6dB above its input sensitivity , average of the RMS value for the first 4 consecutive peaks
22K filter 22K filter @ Speaker Outputs Measured at amplifier board 90% of full Measured at the speaker cable. 225 Watts @ power THD < 0.1 % @ 50 Hz
50 13 6.38 43.7 50
Hz mVrms mVrms dB dB
50 ±1dB ±1dB Reference Reference
Nominal Freq. To 1 Watt To 1 Watt
Single input driven Single input driven, LFE switch ON Single input driven L or R inputs (Local inputs) Single input driven LFE Mode local input
80 60 <1.5
dBA dBr mVrms(max)
75 55 2.5
relative to 1W relative to 1W Volume @max, w/ A/P Swept Bandpass Measurement (Line freq.+ harmonics) (BW=20 KHz)
A-Weighting filter 22K filter Line level inputs must be terminated using 1KOHM
Input Impedance Line Input (L, R,LFE) Filters LP filter Variable (Normal mode) Subsonic filter (HPF) 2nd Order Friend circuit LFE Low pass Limiter THD at Max. Output Power
10K
ohms
n/a
Nominal
50-150 Fixed Fixed 200>LP<500
Hz
± 10
4th Order variable-24 db/Octave
Hz
LFE input driven only
5
%
functional
Drive unit 6dB above the required level to obtain full power Approximately Maximum THD as a result of limiting. 800mV single input driven, L or R input
Features Volume pot Taper (lin/log) Phase switch LP Filter defeat switch Wireless ready Wireless channels LED Indicator Input Configuration Line in (L,R) & LFE Signal Sensing (ATO) Auto-Turn-On (yes/no) ATO Input test frequency ATO Level LFE Input ATO Turn-on time Auto Mute/ Turn-OFF Time Power on Delay time
-LOG 0-180 YES YES 4 YES
-deg
functional functional functional functional
A Taper Disables LP filter, Wireless mode only, it has no effect when using local inputs Refer to Wireless section below System is provided with 4 wireless channels, which can be selected via a rear panel switch, channel should match ID at Tx side RED-Standby, GRN-Active, ORG-Wireless link and subwoofer are active.
n/a
functional functional
YES
--
functional
Dual RCA jack
YES 50 2 5 5-15 3
Hz mV ms minutes sec.
functional functional functional functional 5-15 4 Amp connected and AC on, then input signal applied T before muting, after signal is removed AC Power Applied
Maximum acceptable level.
Auto turn of time (T) must be 5 > T < 15 Minutes
2
PS212W subwoofer
Parameter Transients/Pops ATO Transient Turn-on Transient Turn-off Transient Efficiency Efficiency Efficiency at 1/8 of rated power Standby Input power Idle input power Power Cons. @ rated power Protections Short Circuit Protection YES functional Direct short at output @1/8 max unclipped Power at 1.06 times the input voltage Amplifier should resume operation after short circuit condition removal Temperature rise in accessible metal parts should not exceed 35K rise for domestic version or 30K rise for European versions (refer to requirements sheet). Design must insure no Offset/DC Voltage at the speaker output under any operating condition including abnormal operation 0.5 0.5 0.5 V-peak V-peak V-peak 0.5V 0.8V 0.8V @ Speaker Output @ Speaker Output @ Speaker Output Amplifier activated by signal presence at the Line input AC Line cycled from OFF to ON AC Line cycled from ON to OFF Specification Unit QA Test Limits Conditions Notes
65 48 10 14 388
% % Watts Watts Watts
60 45 12 20 416
Test conducted at rated power 250W Test conducted at 31.25 WRMS
Nominal Line voltage Nominal Line voltage-Rated impedance 4 Ohms Nominal Line voltage RED LED
@ nom. line voltage @ nom. line voltage
Maximum allowable input power under nominal Input voltage and frequency, HOT or COLD operation. LED GREEN no signal applied 250 Watts @ 4 Ohms nominal line voltage
Thermal Protection
YES
functional
DC Offset Protection Line Fuse Rating USA-Domestic EU
YES
-
DC present at Speaker Out leads
3.15 2
Amps Amps
3.15 2
Type-T or Slo Blo-250 V Internal fuse with UL/SEMKO rated holder Type-T or Slo Blo-250 V, Low Breaking Internal fuse with UL/SEMKO rated holder capacity
SYSTEM PERFORMANCE USING WIRELESS Tx THD @ 1 Watt Tx Input Impedance Line Input (LFE) System Sensitivity Input Frequency LFE Input System gain System Signal to Noise SNR-A-Weighted SNR-unweighted Filters System filter Tx Limiter THD at Max. Output Power Tx-Signal Sensing (ATO) Auto-Turn-On (yes/no) ATO Input test frequency ATO Level LFE Input Auto Mute/ Turn-OFF Time Tx Features LFE Input Channel ID switch External power supply requirements Power comsumption Tx Standby Input Power Tx Standby input current Tx Idle Power 5.7 Vrms functional Max input voltage Tx front end can handle without exceeding 1% THD None Hz Should not have any effect on the FR of the system 0.2 % 0.3 22K filter
7.3K
ohms
n/a
Nominal @ 1KHz Using Tx Nominal Freq. To 1 Watt To 1 Watt Using Tx relative to 1W relative to 1W
50 6.187 50
Hz mVrms dB
50 ±1dB ±1dB
System level, using Tx System level, using Tx System level, using Tx
65 55
dBA dBr
65 55
A-Weighting filter 22K filter
YES 50 2 5-15 -YES YES 18
Hz mV minutes
functional functional functional 5-15 T before muting, after signal is removed Auto turn of time (T) must be 5 > T < 15 Minutes
--
functional functional
Single RCA Connector 4 Position switch, to select wireless channels System provided with Power supply model GPE152, delivering 18VDC @ 400mA
VDC
functional
1 0.019 2.34
Watts Amperes Watts
Reference Reference Reference
120VAC line voltage 120VAC line voltage 120VAC line voltage
Tx Idle Power 1.64 Watts Reference 120VAC line voltage Other Parameters/Notes: 1. Volume control should be at the input buffer stage in order to lessen the possibility of clipping the input section with highly dynamic audio material. 2. ALL SPECS SHOULD BE MEASURED AT NOMINAL LINE VOLTAGE.
RED LED RED LED Unit in operation Locked to Rx section Solid GRN Unit in operation NOT locked to Rx section
3
PS212W subwoofer
PACKAGING
4
PS212W subwoofer
CONTROLS AND CONNECTIONS
Rear Panel
Antenna
Sub In
Wireless
ID Code L Low-Pass Crossover R
Low-Pass
Level
Off LFE
Green: Sub On Red: Standby Orange: Sub On and Wireless Link Active
Phase On Min Max
Off
On
¡ Power Switch TM Line-Level Input £ LFE Input ¢ Subwoofer ID-Code Selector Status LED § Low-Pass Selector (Wireless Input Only) ¶ Crossover Adjustment
· Subwoofer-Level Control ª Phase Switch , Antenna / Transmitter Antenna ¤ Transmitter Power Supply Input < Transmitter ID-Code Selector > Transmitter Sub Input
DC18V
ID CODE 1 2 3 4
Sub In
PS210W, PS212W (120V)
5
PS212W subwoofer
SYSTEM CONNECTIONS
Choose either Wireless or Wired Connection; then follow the appropriate instructions.
WIRELESS
Connecting the Subwoofer for Wireless Applications
WIRED
Connecting the Subwoofer for Wired Applications
If you have a Dolby® Digital or DTS® receiver/processor with a low-frequency effects (LFE) or subwoofer output:
ID CODE
DC18V
1 2 3 4
Sub In
Step 1. Connect a subwoofer cable from the subwoofer or LFE output of your receiver to the Sub In > on the transmitter. Step 2. Plug the transmitter module into the wall outlet, and connect the included power supply and power cord to the transmitter ¤. Make sure the Transmitter Antenna / is extended upward. Step 3. Set the ID Code on the transmitter < and subwoofer ¢ to the same position, as described on page 6. When connected properly, the LED on the rear of the subwoofer will be orange. Step 4. Set the Low-Pass Selector § to the "Off" position. NOTE: You may also connect a full-range output (such as a preamp output or second-room output) from an A/V receiver or processor. In that case, set the Low-Pass Selector § to the "On" position, and set the Crossover Adjustment ¶ as described on page 6. Some receivers have two subwoofer outputs. In that case, use either connector.
If your receiver/processor does not contain a Dolby Digital or DTS processor, but has subwoofer outputs:
NOTE: If your receiver/processor has only one sub out, you may use either the L or R input.
PS210W, PS212W (120V)
6
PS212W subwoofer
OPERATION
Power On
Connect your signal source (such as an A/V receiver or preamplifier) to the transmitter (if using a wireless connection) or to the subwoofer (if using a wired connection).Two single-RCA cords are provided.While you would ordinarily use the short cable to connect to the transmitter, or the long one to connect to the subwoofer, either cable can be used, depending on proximity to the signal source.There is no need or benefit gained from connecting the same source to both the transmitter and the subwoofer. However, you could connect two separate sources to the subwoofer by utilizing both its wired and wireless connections. Both signals will essentially be mixed and output by the subwoofer. Plug your transmitter's (if using a wireless connection) and subwoofer's AC cord into a wall outlet. Do not use the outlets on the back of the receiver for the subwoofer. Initially set the Subwoofer-Level Control · to the "Min"position. Turn on your sub by pressing the Power Switch ¡ on the rear panel. Turn on your entire audio system and start a CD or movie soundtrack at a moderate level. that the RCA cable from the source to subwoofer (wired connection) or transmitter (wireless connection) is functioning properly and that it is fully inserted at both ends, or that the Transmitter ID-Code Selector < and the Subwoofer ID-Code Selector ¢ are set to the same channel. Once you have a green or orange LED on the subwoofer, turn your Subwoofer-Level Control · up halfway so that the knob indicator points up.You should now be hearing bass information coming from the subwoofer.
Adjust Level
Set the overall volume control of the preamplifier or stereo to a comfortable level. Adjust the Subwoofer-Level Control · until you obtain a pleasing blend of bass. Bass response should not overpower the room but rather be adjusted so there is a harmonious blend across the entire musical range. Many users have a tendency to set the subwoofer volume too loud, adhering to the belief that a subwoofer is there to produce lots of bass.This is not entirely true. A subwoofer is there to enhance bass, extending the response of the entire system so the bass can be felt, as well as heard. However, overall balance must be maintained or the music will not sound natural. An experienced listener will set the volume of the subwoofer so that its impact on bass response is always there but is never obtrusive.
Auto On/Standby
Transmitter (Wireless Connection Only): The Status LED (not shown) will be lit in red when the unit is in Standby mode. When the transmitter receives an audio signal from the source, it will immediately turn on and the LED will turn to blinking green or solid green: RED = STANDBY (No signal detected, transmitter off) GREEN (BLINKING) = Transmitter is ON but has not established a link with the wireless sub GREEN (SOLID) = Transmitter is ON and has already established a link with the wireless sub The transmitter will automatically enter Standby mode after approximately 10 minutes when no signal is detected from your system. Subwoofer: With the Power Switch ¡ in the "On"position, the Status LED on the back panel will remain lit to indicate the On/Standby mode of the subwoofer. RED = STANDBY (No signal detected, Amp Off) GREEN = SUB ON (Wired signal detected, Amp On) ORANGE = SUB ON (Wireless link with transmitter active) The subwoofer will automatically enter Standby mode after approximately 10 minutes when no signal is detected from your system.The subwoofer will then power on instantly when a signal is detected. During periods of normal use, the Power Switch ¡ can be left on.You may turn off the Power Switch ¡ for extended periods of nonoperation, e.g., when you are away on vacation.
Phase Control
The Phase Switch ª determines whether the subwoofer speaker's piston-like action moves in and out with the main speakers, 0°, or opposite the main speakers, 180°. Proper phase adjustment depends on several variables such as room size, subwoofer placement and listening position. Adjust the phase switch to maximize bass output at the listening position.
Crossover Adjustment
The Crossover Adjustment Control ¶ determines the highest frequency at which the subwoofer reproduces sounds. If your main speakers can comfortably reproduce some low-frequency sounds, set this control to a lower frequency setting, between 50Hz and 100Hz.This will concentrate the subwoofer's efforts on the ultradeep bass sounds required by today's films and music. If you are using smaller bookshelf speakers that do not extend to the lower bass frequencies, set the Crossover Adjustment control to a higher setting, between 120Hz and 150Hz. NOTE: This control will have no effect if the LFE Input £ is used (wired connection) or if the Low-Pass Selector § is in the "Off" position (wireless connection). If you have a Dolby Digital or DTS processor/receiver, the Low-Pass Frequency is set by the processor/receiver. Consult your owner's manual to learn how to view or change this setting.
Getting Started
Confirm that the Status LED on the transmitter is on (red or green), the Status LED on the subwoofer is on (red, orange or green) and an RCA cable is connected from a source unit to either the LFE Input of the subwoofer £ or transmitter > or L and R inputs TM on the subwoofer. Play a CD or video. Use a selection that has ample bass information. If using a wireless connection, the Status LED on the transmitter should be lit solid green, and the Status LED on the subwoofer should turn orange if connected wirelessly. If the LED on the transmitter is blinking green and the LED on the subwoofer is in red or green, a wireless link has not been established between the transmitter and the subwoofer. If connecting directly to the subwoofer without using the wireless link, the Status LED on the subwoofer should be lit green. If the LED on the subwoofer remains red, check
ID Codes
In the unlikely event that you experience interference when operating the system, or if you have more than one set of subwoofer transmitters and receivers in operation, you may change the channel in which the system operates. On both the transmitter module and the subwoofer, there is a four-position ID-Code Selector.Try setting both selectors to a different position. Make sure that the Transmitter ID-Code Selector < and the Subwoofer ID-Code Selector ¢ are set to the same position; the system won't function properly unless the positions match. A maximum of two subwoofers, at least 10' apart, can be operated using the same transmitter. Simply set the channel selector on the transmitter and on the two subwoofers to the same channel.
PS210W, PS212W (120V)
7
PS212W subwoofer
8
PS212W subwoofer
9
PS212W subwoofer
PS212W Test Set Up and Procedure
Equipment needed: · Function/signal generator/sweep generator · Integrated Amplifier · Multimeter · Speaker cables · PS212W Transmitter, power supply General Unit Function + Transmitter (UUT = Unit Under Test) 1) From a mono output signal generator, OFF at this time, connect an RCA cable to the "Sub in" jack on the PS212W Transmitter. Assure the power supply has been plugged in and a Red or blinking Green LED is now showing on the transmitter. Default "ID Code" switch position is 1. 2) Position and plug in the PS212W Subwoofer nearby (less than 75' away), power switch should be OFF. 3) CROSSOVER, PHASE switch position does not matter. Low Pass switch should be OFF. "ID Code" switch position should be 1. 4) Turn the LEVEL control on the UUT to completely counterclockwise (MIN). 5) Turn on signal generator; adjust to 100mV, 50 Hz. LED on Transmitter should now be steady Green. 6) Turn the power switch ON. LED on Sub Amp plate should be momentarily Green, then Orange. 7) Turn LEVEL control full clockwise (MAX); immediate and vigorous bass response should be heard and felt from port tube opening. 8) Turn off generator, turn LEVEL control full counterclockwise (MIN), and disconnect RCA cable. General Unit Function (Direct connection - No Transmitter) 9) From a mono output signal generator, OFF at this time, connect an RCA cable to the L/R jacks on the PS212W Subwoofer.; Use a Y-cable to connect to both inputs; power switch should be OFF. 10) PHASE switch position does not matter. CROSSOVER control should be set at "150Hz". Low Pass switch position does not matter. 11) Turn the LEVEL control on the UUT to completely counterclockwise (MIN). 12) Turn on signal generator; adjust to 100mV, 50 Hz. 13) Turn the power switch ON. LED on top of Subwoofer should be momentarily Red, then Green. 14) Turn LEVEL control full clockwise (MAX); immediate and vigorous bass response should be heard and felt from port tube opening. 15) Turn off generator, turn LEVEL control full counterclockwise (MIN), and disconnect RCA cable.
10
PS212W subwoofer Sweep Function 1) Follow steps 9-14 above, using a sweep generator as a signal source. 2) Sweep generator from 20Hz to 300Hz. Listen to the cabinet and drivers for any rattles, clicks, buzzes or any other noises. If any unusual noises are heard, remove woofer and test. Driver Function 1) Remove woofer from cabinet; detach + and - wire clips. 2) Check DC resistance of woofer; it should be 3.3 ohms ±10% 3) Connect a pair of speaker cables to driver terminals. Cables should be connected to an integrated amplifier fed by a signal generator. Turn on generator and adjust so that speaker level output is 5.0V. 4) Sweep generator from 20Hz to 1kHz. Listen to driver for any rubbing, buzzing, or other unusual noises.
11
PS212W subwoofer
Wireless PCB
12.288MHz
Pre amp PCB
protection Crossover control U102 mute -15V GND +15V signal input
Power
protection mute -15V GND +15V signal input Power regulator circuit Class_d Amp model
amp PCB
To speaker
Relay
Ac in
12
PS212W subwoofer
PS212W Testing Flow Chart
Start yes Test protection Dc voltage check ±Vcc,±15V OK no OK yes Power on check LED red &green Check vol module OK yes no Test frequency Response OK yes Check U102,uR133, C121,R135,C122.etc Auto off Function Hi pot test Check U103.Q101. Q102.C131.R142;Ac cord, Transformer. yes Listening test no OK yes Test input sensitivity no OK Check U101,R117, R112,R114 etc
13
Check U105 C137C137CC143etc
no yes
Check U107.R237 ±15Vcc etc
Check transformer C168,C169,D123, D124,C170
Test limiter circuit
OK yes
no
Check U106.Q107etc
no
& connector cable& ±15V.etc
Check THD output power, noise Check pre board & power board , ±Vcc,±15V etc
no OK yes Test frequency Response
no OK
no OK yes The Amp ass'y ok END
PS212W subwoofer
Transmitter Troubleshooting Flow Chart
AMP no signal out no yes check +VD(17VDC) yes
Check+VA(15VDC)
Check,D1,L01,D05,Q04,D0 3,Q03,Q01,Q02 etc yes
no Check Q06,Q05 etc yes
yes
Check+12VDC +3.6VDC
no
yes
Check,Q07,D08 .U01,D10,U02etc
led red Check,U05,U06,U08,Q11,Q12,U03,U04 etc LED light green or red LED light green
yes
no
Check MD01 AINL,AINR signal
CheckU07,U05,U06 etc
yes
Check LAUNCHER
yes signal yes no
Check MD01WH4924
The Amp ass'Y OK, END
14
PS212W subwoofer
Wireless Receiver board Troubleshooting Flow Chart
AMP no signal out no yes Check 3.7VDC Check,R505,U501,D501,L5 01,L502,U01, etc
yes
Check MD01 LRCK signal
yes no
Check U04,U02,U03,etc
yes
Check LAUNCHER
yes signal yes no
Check MD01 RX-11G
The Amp ass'Y OK, END
15
PS212W subwoofer
16
PS212W subwoofer
17
PS212W subwoofer
1 3
2
1 3
2
18
PS212W subwoofer
19
PS212W subwoofer
20
PS212W subwoofer
21
PS212W subwoofer
22
PS212W subwoofer
PS212W (120v) Electrical Parts List
Part Number Description Qty Reference Designator
MAIN/POWER SUPPLY PCB
Resistors 109-1TSC103J0-E 110-12621J15-E 110-20152J20-E 116-142003F26-E 113-50R10J10-E 110-16153J26-E 110-16182J26-E 110-16274J26-E 110-16333J26-E 110-16391J26-E 110-16683J26-E 112-14101J26-E 116-161002F26-E 116-161301F26-E 116-161692F26-E 116-162001F26-E 116-162492F26-E 116-166813F26-E 116-141R00J26X-E 110-16102J26-E 110-16103J26-E 110-16222J26-E 110-16223J26-E 110-16472J26-E 110-16473J26-E Capacitors 130-2b102k503-e 130-3F104Z503-E 130-CH101J503-E 135-3107M16-E 135-3226M50-E 135-3227M10-E 139-3227M16-E 140-RX103KA03-E 140-RX473KB53-E 135-4228M35-E 135-4688M80-E 130-3F104ZA03-E Semiconductors 190-16L431CLP1-E 192-027C1815GR-E 192-028A1015GR-E 192-1572N5551-E 192-1582N5401-E 199-65000563G-E 199-65001503G-E 199-65002003G-E 197-631N4148-E 192-991d669a-e 192-992B649T-E 197-00KBU1003-E 190-16LM324N-E 197-101N4002-E 197-00DB103G-E
IC TL431CLP (RoHS) PROGRAMMABLE VOLTAGE REFERENCE
Resistor TSC05103J 10K +/-5% (RoHS) Resistor 620 1/2W ±5% 15mm(RoHS) Resistor 1.5K 2W ±5% CF 20mm KINK(RoHS) Resistor 200K 1/4W ±1% MF26mm (RoHS) Resistor 0.1 5W ±5% (RoHS) Resistor 15K 1/6W ±5% CF 26mm (RoHS) Resistor 1.8K 1/6W ±5% CF 26mm(RoHS) Resistor 270K 1/6W ±5% CF 26mm(RoHS) Resistor 33K 1/6W ±5% CF 26mm(RoHS) Resistor 390 1/6W CF 26mm (RoHS) Resistor 68K 1/6W ±5% CF 26mm (RoHS) Resistor 1/4W100ohm 5% (RoHS) Resistor 10K 1/6W ±1% MF 26mm (RoHS) Resistor 1.30K 1/6W MF 26mm (RoHS) Resistor 16.9K 1/6W MF 26mm (RoHS) Resistor 2.00K 1/6W ±1% MF26mm (RoHS) Resistor 24.9K 1/6W ±1% MF26mm (RoHS) Resistor 681K 1/6W ±1% MF26mm (RoHS) Resistor 1.00 1/4W±5% MO 26mm (Fireproof Resistor) Resistor 1K 1/6W ±5% CF 26mm (RoHS) Resistor 10K 1/6W ±5% CF 26mm (RoHS) Resistor 2.2K 1/6W ±5% CF 26mm(RoHS) Resistor 22K 1/6W ±5% CF 26mm (RoHS) Resistor 4.7K 1/6W ±5% CF 26mm (RoHS) Resistor 47K 1/6W ±5% CF 26mm (RoHS)
1 1 1 1 2 2 1 1 1 2 1 2 2 3 1 1 2 1 2 3 9 2 3 4 1
R237, R238, R208, R209, R224,R225, R247,R249, R248, R240, R211, R243,R246, R212, R241,R244, R234,R235, R226,R228,R236, R214, R215, R257,R258, R262, R255,R256, R210,R239,R264 R216,R227,R229,R230,R231,R232,R233,R260,R261, R242,R245, R218,R220,R223, R213,R217,R219,R222, R221,
Capacitor 1000P 50V ±10% (RoHS) Capacitor 0.1U 50V +80/-20% (RoHS) Capacitor 100P 50V ±5% (RoHS) Capacitor 100uF 16V ±20% (RoHS) Capacitor 22U 50V ±20% (RoHS) Capacitor 220U 10V ±20% (RoHS) Capacitor 220uF 16V±20% (RoHS) Resistor 10nF 100V X7R 10% (RoHS) Capacitor 47NF 250V X7R±10% (RoHS) Capacitor 2200uF 35V ±20%(RoHS) Capacitor 6800U 80V ±20%(RoHS) Capacitor 0.1U 100V (RoHS)
1 2 2 2 2 2 1 1 2 2 2 2
C165, C163,C164, C159,C160, C166,C167, C161,C162, C156,C157, C155, C174, C172,C173, C170,C171, C168,C169, C168A,C169A
transistor 2SC1815GR TOSHIBA(RoHS) NPN transistor 2SA1015GR TOSHIBA(RoHS) PNP transistor FSC 2N5551 (RoHS) NPN Transistor FSC 2N5401 AI-PNP 350V500mA TO-92 (RoHS) Diode GDZJ5.6B 500mW 5.6V26mm 2% (RoHS) Diode GDZJ15C500mW 15V 2%ROHM 52mm 1N5245B (Ro Diode GDZJ20D 500mW 20V26mm 2% (RoHS) Diode 500mW 75V 1N4148 Panjit (RoHS) transistor HI-SINCERITY HSD669A (RoHS) NPN transistor HSB649T (RoHS) PNP Rectifier 10A 200V KBU1003(RoHS) I.C. LM324N (RoHS) QUAD OP-AMP Diode 1N4002TB (RoHS) Rectifier 1A 200V DF02MDB103G (RoHS)
1 4 3 1 1 1 1 1 7 1 1 1 1 1 1
D115, Q110,Q112,Q114,Q117, Q111,Q113,Q115, Q109, Q108, D116, D122, D129, D117,D118,D119,D120,D121, D125,D126 Q116, Q118, D123, U107, D114, D124,
23
PS212W subwoofer
Part Number Description Qty Reference Designator
MAIN/POWER SUPPLY PCB
Miscellaneous 171-UDHSS124D-E 175-1d02v01-e 175-1d05v01-e 362-FE-00041-0LAE 175-1c06v01-e 175-1C02V01-E 120-1000003-E Relay 5A 24V UDH-SS124D(RoHS) Connector 2PIN PITCH=3.96mm(RoHS) Connector 5PIN 3.96mm (RoHS) PCB stand 11.75*8.5*12.5H(RoHS) Connector 6 PIN PITCH=2.5mm(RoHS) Connector 2PIN PITCH=2.5mm (RoHS) Inductor 10W AI YT-C3104-0051CRHW354708LTBS LF 1 1 1 1 1 1 2 K101, P112, P113, P107, P108, J161,J165,
INPUT/PREAMP PCB
Resistors 118-08050000J-E 118-08051000F-E 118-08051001J-E 118-08051002F-E 118-08051002J-E 118-08051004F-E 118-08051201J-E 118-08051500F-E 118-08051504F-E 118-08051542F-E 118-08051652F-E 118-08051802J-E 118-08052001F-E 118-08052002F-E 118-08052200J-E 118-08052202F-E 118-08052202J-E 118-08052212F-E 118-08052262F-E 118-08052803F-E 118-08053011F-E 118-08053301J-E 118-08053401F-E 118-08054301F-E 118-08054421F-E 118-08054701F-E 118-08054702F-E 118-08054702J-E 118-08054703J-E 118-08054991F-E 118-08054R70F-E 118-08055101F-E 118-08055363F-E 118-08056191F-E 118-08056801F-E 118-08059762F-E 115-H103A101-E 115-H503B405-E Capacitors 141-B0101J50-E 141-B0221J50-E 141-B0330J50-E 141-B0470J50-E 141-B0680J50-E CAP CERAMIC/CHIP 100PF 50V CHJNPO 0805 RoHS SMD Capacitor 220P 50V NPO 0805(RoHS) SMD Capacitor 0805 33pF5% 50V(RoHS) SMD Capacitor 47pF 0805 NPO 50V(RoHS) SMD Capacitor 68pF 0805 NPO 50VRoHS 5 3 1 1 1 C110B,C318,C319,C331,C332, C212,C304,C305, C148, C128, C127, SMD Resistor 0805 1/10W 0±5%LF SMD Resistor 0805 1/10W 100 ±1% LF SMD Resistor 0805 1/10W 1K ±5% LF SMD Resistor 10.0K 0805 1/10W 1%(RoHS) SMD Resistor 0805 1/10W 10K ±5%LF SMD Resistor 0.1W 1M 1% (RoHS) SMD Resistor 1.2K 0805 1/10W 5%(RoHS) SMD Resistor 0805 150ohm 1% (RoHS) SMD Resistor 0805 1/10W 1.5M ±1%(RoHS) SMD Resistor 0805 1/16W 15K4 ±1%LF RoHS SMD Resistor 0805 16.5K 1% RoHS SMD Resistor 18K 0805 1/10W 5%(RoHS) SMD Resistor 0.1W 1% 2K (RoHS) SMD Resistor 0805 20.0K 1% (RoHS) SMD Resistor 0805 1/10W 220 5%(RoHS) SMD Resistor 0805 1/10W 22K±1%(RoHS) SMD Resistor 0805 1/10W 22K ±5%LF SMD Resistor 0805 22.1K 1% (RoHS) SMD Resistor 0805 22.6K 1% (RoHS) SMD Resistor 0805 280K 1/10W ±1%(RoHS) SMD Resistor 0805 3.01K 1% (RoHS) SMD Resistor 0805 1/10W 3.3K ±5%(RoHS) SMD Resistor 3.4K 0805 1/10W 1%(RoHS) SMD Resistor 0.1W 1% 4.3K(RoHS) SMD Resistor 0.1W 1% 4.42K(RoHS) SMD Resistor 4.7K 0805 1% (RoHS) SMD Resistor 0805 1/10W 47K±1%(RoHS) SMD Resistor 47K 0805 1/10W 5%(RoHS) SMD Resistor 470K 0805 1/10W 5%(RoHS) SMD Resistor 4.99K 0805 1/10W 1%(RoHS) SMD Resistor 0805 1/10W 4.7 ±1%(RoHS) SMD Resistor 5.1K 0805 1/10W 1%(RoHS) SMD Resistor 0805 536K 1/10W ±1%(RoHS) SMD Resistor 0805 6.19K 1% (RoHS) SMD Resistor 6.8K 0805 1/10W 1%(RoHS) SMD Resistor 0805 1/10W 97.6K ±1%(RoHS) Variable Resistor A10K (RoHS) LEVEL Variable Resistor B50K (RoHS) CROSSOVER JP1,JP3, R125,R151,R152,R215,R314,R315, R140,R401,R405,R406,R410,R400, R199,R263,R111,R118,R122,R124,R133,R136,R146, 16 R149,R308,R130,R131,R132,R330,R331, 2 R402,R403, 1 R145, 1 R409, 1 R139, 1 R142, 2 R197,R198, 1 R117, 1 R147, 1 R202, 2 R200,R193, R159A,R160A,R119,R120,R154A,R155A,R335,R334, 11 R411,R332,R333, 2 R141,R148, 1 R404, 2 R204,R206, 4 R209,R296,R297,R298, 1 R208, 1 R194, 1 R407, 1 R128, 1 R254, 2 R205,R207, 1 R144, 1 R115, 8 R109,R114,R116,R121,R137,R138,R219,R412, 1 R143, 1 R265, 1 R153, 8 R316,R317,R318,R319,R320,R321,R322,R323, 1 R195, 1 R134, 6 R110,R112,R113,R123,R300,R301, 1 R135, 1 VR1, 1 VR2, 2 6 6
24
PS212W subwoofer
Part Number Description Qty Reference Designator
INPUT/PREAMP PCB
C153,C154,C112,C114,C116,C118,C124,C125,C130, 22 C232,C233,C184,C185,C145,C144,C205,C185,C145, C144,C205, 2 C181,C182, 1 C110, 2 C120,C317, 1 C110A, 1 C149, 2 C121,C122, 2 C209,C218, 1 C150, 2 C201,C213, C109,C111,C123,C129,C133,C134,C141,C310,C311, 10 C126, C152,C159,C160,C155,C156,C113,C115,C117,C119, 16 C132,C157,C158,C327,C328,C329,C330 2 C312,C151, 1 C131,
141-B5104Z50-E 141-B7222K50-E 141-B7272K50-E 141-B7332J50-E 141-B7472J50-E 129-A104J633-E 129-A224J633-E 129-A333J633-E 129-A473J633-E 129-A683J633-E 135-3106M25-E 135-3107M16-E 135-3226M25-E 139-3227M16-E Semiconductors 190-16TL072DTS-E 190-16TL074CDS-E 192-027C1815GRS-E 192-998A1015GRS-E 197-0S4148WSP-E 199-6200039D-E 192-153J111-E 195-443391EV-E Miscellaneous 162-5009D006-E 180-SS14H03GT-E 162-10169003-E 162-8008D001-E 174-0RCA313G-E 175-1C02V01-E 180-T000TS81-E 362-FE-00041-0LAE
Capacitor CAP SMD 0805 Y5V0.1uF +80/-20% 50V LF SMD Capacitor 2.2nF ±10% 50V 0805X7R (RoHS) SMD Capacitor0805 2700PF 50V X7R(RoHS) SMD Capacitor 0805 X7R 3300pF 5%(RoHS) SMD Capacitor 0805 X7R 4700PF 5% 50V(RoHS) Capacitor 0.1U 63V ±5% MSC (RoHS) Capacitor 0.22uF 63V ±5% MSC(RoHS) Capacitor 0.033U 63V MSC (RoHS) Capacitor 0.047U 63V ±5% MSC (RoHS) Capacitor 0.068U 63V ±5% MSC RoHS Capacitor 10uF 25V ±20% (RoHA) Capacitor 100uF 16V ±20% (RoHS) Capacitor 85 22uF ±20%25V LF Capacitor 220uF 16V±20% (RoHS)
I.C. TL072N @6.5 (RoHS) DUAL OP-AMP I.C TL074CN ST (RoHS) QUAD OP-AMP SMT transistor MMBT1815 SOT-23(RoHS) SMD transistor MMBT1015 CJ SOT-23(RoHS) SMD Diode LL4148WSP 0805SHAWELL Diode 3.9VBZ52-C3V9S SOD-323(RoHS) FET J111 FAIRCHILD (RoHS) Bipolar LED 339-1EVGW(339-1SURSYGW/S350-A3(RoHS)
4 2 5 2 10 1 1 1
U101,U103,U108,U109, U106,U102, Q101,Q102,Q103,Q402,Q403, Q400,Q401, D400, D130, Q107, D401,
Wire 90mm P=2.0mm(RoHS) SLIDE SW SS14H03GT-GP(RoHS) WIRELESS ID Wire 160mm AWG28 (RoHS) Wire 80mm 4pin P=2.0mm(RoHS) RCA Jack RCA-313G (RoHS) INPUT/LFE Connector 2PIN PITCH=2.5mm (RoHS)
Toggle Switch L101 T2 T8019L-SNQ-E-H+U RoHS LO-PASS,PHASE
PCB stand 11.75*8.5*12.5H(RoHS)
1 1 1 1 1 1 2 1
P105, P1, JK1, P106, SW103,SW105 BK2,
EQ DAUGHTER BOARD
175-9F08HR2-E 190-16TL072N-E 116-161542F26-E 129-A104J633-E 129-A473J633-E 116-161822F26-E 116-161911F26-E 129-A683J633-E 116-169092F26-E 116-165901F26-E 116-162051F26-E 116-161001F26-E 130-3F104Z503-E Connector 8PIN PITCH=2.54mm(RoHS) I.C. TL072N @6.5 (RoHS) DUAL OP-AMP Resistor 1/6W 15.4K 1% 26mm (RoHS) Capacitor 0.1U 63V ±5% MSC (RoHS) Capacitor 0.047U 63V ±5% MSC (RoHS) Resistor 18.2K 1/6W ±1% MF26mm (RoHS) Resistor 1.91K 1/6W±1% MF26mm (RoHS) Capacitor 0.068U 63V ±5% MSC RoHS Resistor90.9K 1/6W MF 26mm (RoHS) Resistor 5.90K 1/6W ±1% MF26mm (RoHS) Resistor 2.05K 1/6W MF 26mm (RoHS) Resistor 1K 1/6W ±1% MF26mm (RoHS) Capacitor 0.1U 50V +80/-20% (RoHS) 1 1 2 1 1 1 2 2 1 1 1 1 2 P104, U105, R173,R178, C137, C138, R188, R251,R191, C143,C142, R190, R189, R253, R252, C144,C145,
CLASS D PCB ASS'Y (RECOMMENDED REPLACE ENTIRE MODULE PART# 051-A05022C-E)
Resistors 112-10180J00-E Fuse resistor FMF 1W 18 5%(RoHS) 1 R47
25
PS212W subwoofer
Part Number Description Qty Reference Designator
CLASS D PCB ASS'Y (RECOMMENDED REPLACE ENTIRE MODULE PART# 051-A05022C-E)
118-12061001F-E 118-12061002F-E 118-12061002J-E 118-120610R0J-E 118-12062002F-E 118-12062201J-E 118-12062204J-E 118-12062211F-E 118-12062550F-E 118-12062701J-E 118-12063301J-E 118-12063321F-E 118-12063922F-E 118-12064700J-E 118-12064701J-E 118-12064751F-E Capacitors 132-104KB50-E 129-A104JA03-E 128-E106MA01-SE 132-105KB50-E 130-SL681KB03-E 141-C0101K50-E 141-C0220K50-E 141-C0561K50-E 141-C5104M50-E 141-C7103K50-E 141-D7104KB5-E Semiconductors 190-16tl072dts-e 192-09124126qs-e 192-09139066rs-e 192-091SC4672-E 192-09210376qs-e 192-09215146rs-e 197-03rls4148s-e 199-15000563S-E 199-1500120s-e 192-1582N5401-E 192-232IRF9640-E 192-233F640N-E Miscellaneous 175-9F02H02-E 175-9F03H020-E 359-FIB-00125-E 122-13151K0190-E 122-14300K4-E Connector 2PIN PITCH=2.54mm(RoHS) Connector 3PIN PITCH=2.54mm(RoHS) Gasket 10*5*0.5T (RoHS) CHOKE SA-500-280(PT1601B*151MAA) (RoHS) Ferrite core LD1215*300KU±10% RoHS 1 2 2 1 1 HDR3, HDR1,HDR2, L1, L2,
SMD I.C. TL072CDT SGS THOMSON(RoHS) DUAL OP-AMP SMD transistor 2SC2412K-T146Q/RROHM (RoHS) SMD transistor 2SC3906K-T146R ROHM(RoHS) Transistor 2SC4672(MPT3) ROHM(RoHS) SMD transistor 2SA1037K-T146Q/RROHM (RoHS) SMD transistor 2SA1514K-T146R ROHM(RoHS) SMD diode RLS4148-TE11 ROHM(RoHS) SMD ZENER 5.6V 5% PHILIPSBZX84-C5V6(RoHS) SMD ZENER 12V 5% PHILIPSBZX84-C12 (RoHS) Transistor FSC 2N5401 AI-PNP 350V500mA TO-92 (RoHS) FET IRF9640 IR P-CH TO220(RoHS) Transistor IRF640N INTERNATIONAL(RoHS)
SMD Resistor 1K 1206 1% (RoHS) SMD Resistor 10K 1206 1% (RoHS) SMD Resistor 10.0K 1206 5% (RoHS) SMD Resistor 10.0 1206 5% (RoHS) SMD Resistor 20K 1206 1% (RoHS) SMD Resistor 2.20K 1206 5% (RoHS) SMD Resistor 2.20M 1206 5% (RoHS) SMD Resistor 2.21K 1206 1% (RoHS) SMD Resistor 1206 255 1% (RoHS) SMD Resistor 2.70K 1206 5% (RoHS) SMD Resistor 3.30K 1206 5% (RoHS) SMD Resistor 3.32K 1206 1% (RoHS) SMD Resistor 1206 39.2K±1% (RoHS) SMD Resistor 470 1206 5% (RoHS) SMD Resistor 4.7K 5% 1206(RoHS) SMD Resistor 4.75K 1206 1% (RoHS)
R2, R25, R29,R30,R30B,R7,R9, R20,R20B,R22,R23, R26, R13,R16,R31,R33,R34,R35,R36,R37,R38,R39,R40, 18 R41,R42,R43,R44,R45,R46,R32, 1 R4, 1 R6, 1 R24, 1 R10, 4 R14,R15,R27,R28, 1 R1, 1 R3, 3 R8,R11,R21, 1 R12, 1 R5, 1 1 5 4 1
Capacitor 0.1U ±10% 250V (RoHS) Capacitor 0.1U 100V ±5% MSC (RoHS) Capacitor 10uF 100V 20%(RoHS) Capacitor 1uF 250V ±10% (RoHS) Capacitor SL 680PF 200V (RoHS) SMD Capacitor 100pF 50V 10%1206 NP0 (RoHS) SMD Capacitor 22pF 50V 10% 1206SMT NPO (RoHS) SMD Capacitor 560pF 50V 10%1206 NPO (RoHS) SMD Capacitor 1206 Y5V 0.1uF50V ±20% (RoHS) SMD Capacitor 10nF 50V 1%1206 X7R (RoHS) SMD Capacitor 0.1uF 250V 10%1210 X7R (RoHS)
1 2 2 1 1 1 1 1 8 1 2
C20, C12B,C14, C16,C17, C40, C21 C4, C5, C6, C2,C3,C7,C8,C9,C10,C11,C15, C13, C18,C19,
1 2 2 1 2 1 8 2 4 1 2 1
IC1, Q1,Q4, Q2,Q8, Q5B, Q7,Q9, Q3, D1,D2,D3,D4,D5,D5B,D6,D20, Z1,Z2, Z3,Z4,Z5,Z6, Q6B, Q10,Q10B, Q11,
WIRELESS RECEIVER PCB
Resistors 116-1410R0J5VX-E 118-08050000J-E 118-08051002J-E Resistor 10 1/4W ±5% (RoHS) SMD Resistor 0805 1/10W 0±5%LF SMD Resistor 0805 1/10W 10K ±5%LF 1 8 3 R505, R21,R27,R28,R29,R30,R36,R37,R22, R26,R12,R13,
26
PS212W subwoofer
Part Number Description Qty Reference Designator
WIRELESS RECEIVER PCB
118-08051200F-E 118-08052002J-E 118-08052400F-E 118-08052703J-E 118-08053303J-E 118-08054701J-E 118-08054702J-E 118-08054R70J-E 118-080556R0J-E 118-08056200J-E Capacitors 141-B7102J50-E 141-B7103K50-E 141-B7104K50-E 141-B7332J50-E 142-AV107M16H-E 142-SV105M50H-E 142-SV106M16H-E 130-2B104KA03-E 135-3476M100-E 135-3477M16-E Semiconductors 190-145008MMS-E 190-19HCT165S-E 190-99CS4340KS-E 190-99IMP809S-E 197-63S110-E 051-WH4927-E Miscellaneous 121-COMM220M-E 121-COMM221M-E 175-1B04V01A-E 175-1C02V01-E 175-9B06V03-E 175-9Y25V2201-E 333-EVA-05425-0BAE 362-FE-00041-0LAE SMD inductor22UH±20%YC5D18T*220MS(RoHS) SMD inductor220UH±20% YC8D43T*221MS(RoHS) Connector 4PIN PITCH2.0mm (RoHS) Connector 2PIN PITCH=2.5mm (RoHS) Connector 6Pin PITCH=2.0mm(RoHS) PIN HEADER18025PH=1.27mm(RoHS) Gasket EVA 13*10*3MM CONTROL 2.4G (RoHS) PCB stand 11.75*8.5*12.5H(RoHS) 1 1 1 1 1 1 2 2 L502, L501, P1, P501, SW01, SMD IC LM5008MM/NOPB(NATIONAL)(RoHS) High Voltage (100V) Step Down Switching Regulator SMD IC 74HC/HCT165(RoHS)PHILIPS 8-bit parallelin/serial-out shift register IC CS4340-KS 16Pin SoIC(RoHS) 24-Bit, 96 kHz Stereo DAC SMD IC IMP809SEUR-T(IMP)(RoHS) RESET Diode S100 100V 1A SMAD0-214AC(RoHS) Wireless HI-FI Audio RX ModuleWH4927 (RoHS) 1 2 1 1 1 1 U501, U02,U03, U04, U01, D501, MD01 SMD Capacitor 0805 X7R 1nF 50V5% (RoHS) SMD Capacitor 0.01U 50V X7R 0805(RoHS) Capacitor CAP SMD 0805 X7R0.1uF ±10% 50V LF/RoHS SMD Capacitor 0805 X7R 3300pF 5%(RoHS) SMD Capacitor 100UF 16V 6.3*5.4mm (RoHS) SMD Capacitor 1uF 50V 4.3*4.3mm(RoHS) SMD Capacitor 10U 16V (RoHS) Capacitor 0.1uf 100V 10% (RoHS) Capacitor 47uF 100V±20% 10*16 5mm (RoHS) Capacitor 85 470uF ±20%16V LF 1 2 10 2 1 2 3 1 1 4 C06, C03,C505, C02,C05,C08,C09,C10,C14,C16,C504,C507,C509, C20,C21, C11, C15,C17, C12,C13,C18, C503, C501, C01,C04,C511,C506, SMD Resistor 120 0805 1% RoHS SMD Resistor 20K 0805 1/10W 5%(RoHS) SMD Resistor 2400805 1% ROHS SMD Resistor 270K 0805 5% (RoHS) SMD Resistor 330K 0805 5% (RoHS) SMD Resistor 0805 1/10W 4.7K ±5%LF SMD Resistor 47K 0805 1/10W 5%(RoHS) SMD Resistor 4R7 0805 1/10W 5%(RoHS) SMD Resistor 0805 56 1/10W 5%(RoHS) SMD Resistor 0805 620 ±5% (RoHS) R503, R04,R05,R06,R07,R08,R09,R10,R11,R14,R15,R16, 15 R17,R18,R19,R20, 1 R504, 1 R502, 1 R501, 1 R38, 1 R03, 2 R01,R02, 1 L01, 2 R39,R40, 1
BK01,BK02,
EMI/FUSE PCB
154-K31505T0-E 155-630R345B-E 122-14103M4200-E 122-14501M0650-E 130-3F102MB50-E 132-334KB70-E 132-334KB74-E 162-10090003-E 162-10099003-E Fuse 3.15A 250V 30mm UL/CSA/PSE (RoHS) Fuse holder UL/CSA 6*30mm R3-45B (RoHS) Inductor RT251510*103N 10mH (RoHS) Inductor 0.5mH 0.65 (RoHS) Capacitor Y1 1NF 20%250V (RoHS) Capacitor 0.33U 275V +/-10% (RoHS) Capacitor 0.33uF 275V +/-10% LS=15mm (RoHS) Wire 90mm20AWG(RoHS) Wire 90mm20AWG (RoHS) 1 1 1 1 2 1 1 1 1
L02, L01, C03,C04, C02, C01,
MISCELLANEOUS/MECHANICAL
123-11K4DRH-E 123-11RH633215-E Ferrite core K4DRH 16*28.5*9 (RoHS) Ferrite core K5ARH 6.35*3.2*15.8(RoHS) 3 1
27
PS212W subwoofer
Part Number Description Qty Reference Designator
MISCELLANEOUS/MECHANICAL
150-R1107011A-E 1 Power TransformerTT0930505260120V(RoHS) 152-U60201A02-E Power cord 6FT UL 2PIN RoHS 1 153-VPST101S2-E Outlet VDE 2PINS INLETSOCKET PRONIC (RoHS) 1 162-10090003-E WIRE 90mm20AWG (RoHS) 1 162-10129004-E WIRE UL161720AWG (RoHS) 1 162-10130005-E Wire 1007# 24AWG 125mmBLK Tin 5mm RoHS 1 162-5016D001-E WIRE 24# 160mm (RoHS) 1 162-5018D007-E Wire 180mm 2pin 22AWG(RoHS) 1 166-5070A4BD-E Speaker wire 700mm #18 UL1015#205*0.5t BLK/#250*0.8t R 1 180-P3024DB-E Power Switch ROCKER 3024-DB (RoHS) 1 188-ASDWLAN01-E RF ANTENNA ASSEMBLYASD-WLAN-01 (RoHS) 1 193-0S4211-E (INSULATION SPACER)42*11 (RoHS) 1 193-201612TR-E NSULATION SPACER T0-220 16mm*12mm(RoHS) 3 236-050-05017-0BAE Fixer ABS 28*12*12H 1 236-AL-05001-0LAE RITAINER (RoHS) 1 302-AL-05175-1BAE Rear panel 300*200*2.5mm PS212W/120V(RoHS) 1 306-ABS-05079-0BAE Rear plastic enclosure 198*298*102H (RoHS) 1 311-ABS-00028-0BAE Plastic knob 46077-W P.V.C.(RoHS) 2 323-AL-05000-0LAE Heat sink (RoHS) 1 325-FE-00400-0LAE PCB bracket 58*9*13.5T (RoHS) 1 333-EVA-00188-0BAE EVA 170x5x1t (RoHS) 2 333-EVA-00220-0BAE EVA 225*15*1t UL(RoHS) 1 333-EVA-00866-0BAE Fireproof EVA 48*18*1.5T (RoHS) 1 333-EVA-05782-0BAE EVA 90*5*1mm(RoHS) 1 333-SPG-00860-0BAE Fireproof damping material 450*50*5T (RoHS) 1 333-SPG-00863-0BAE Fireproof damping material 100*50*5T (RoHS) 5 335-NYL-05015-0BAE WIRE CLKP SB4F-2 (RoHS) 1 336-RUB-05103-0BAE RUB 97*16*3.0T (RoHS) 2 350-EM04012D024-E 4*12 WOOD SCREW BLACK(RoHS) 4 351-AM02606A011-E M2.6*6 Mechanical screw cross BLK(RoHS) 2 351-AM03008A078-E M3*8 Mechanical screw with nickel(RoHS) 10 351-AM03008A079-E M3*8 Mechanical screw cross BLK(RoHS) 9 351-AM03018A364-E Mechanical screw M3*18 BLK (RoHS) 2 351-HM03006A308-E Mechanical screw M3*6mm cross BLK (RoHS) 1 351-HM04010A217-E M4*10 Mechanical screw cross BLK 4 352-AM02606C1136-E ScrewT26*6 2 352-AM03008D040-E 3*8 B type ping screw cross BLK (RoHS) 2 352-AM03008D041-E 3*8 B type ping screw cross with nickel (RoHS) 2 352-AM03010D065-E 3*10 P type ping screw cross BLK(RoHS) 1 352-BM03010D064-E 3*10 B type ping screw cross BLK(RoHS) 2 354-HM03005-E M3 nut BLK (RoHS) 1 355-P07049-E Washer 7.2*12*0.5t (RoHS) 2 361-FE-00002-0LAE Bracket for Transformer 90*70*15mm (RoHS) 1 362-FE-00013-0LAE PCB bracket L TYPE t=1.6mmS.P.C.C 89*9*1.6T (RoHS) 3 362-NYL-05049-0LAE PCB post M3 10H (RoHS) 2
28
PS212W subwoofer
LM5008 High Voltage (100V) Step Down Switching Regulator
October 2004
LM5008 High Voltage (100V) Step Down Switching Regulator
General Description
The LM5008 Step Down Switching Regulator features all of the functions needed to implement a low cost, efficient, Buck bias regulator. This high voltage regulator contains an 100 V N-Channel Buck Switch. The device is easy to implement and is provided in the MSOP-8 and the thermally enhanced LLP-8 packages. The regulator is based on a hysteretic control scheme using an ON time inversely proportional to VIN. This feature allows the operating frequency to remain relatively constant. The hysteretic control requires no loop compensation. An intelligent current limit is implemented with forced OFF time, which is inversely proportional to Vout. This scheme ensures short circuit protection while providing minimum foldback. Other protection features include: Thermal Shutdown, VCC under-voltage lockout, Gate drive undervoltage lockout, and Max Duty Cycle limiter
Features
n n n n n n n n n n n n Integrated 100V, N-Channel buck switch Internal VCC regulator No loop compensation required Ultra-Fast transient response On time varies inversely with line voltage Operating frequency remains constant with varying line voltage and load current Adjustable output voltage Highly efficient operation Precision internal reference Low bias current Intelligent current limit protection Thermal shutdown
Typical Applications
n Non-Isolated Telecommunication Buck Regulator n Secondary High Voltage Post Regulator n +42V Automotive Systems
Package
n MSOP - 8 n LLP - 8 (4mm x 4mm)
Connection Diagram
20097902
8-Lead MSOP, LLP
Ordering Information
Order Number LM5008MM LM5008SD Package Type MSOP-8 LLP-8 NSC Package Drawing MUA08A SDC08A Supplied As 1000 Units on Tape and Reel 1000 Units on Tape and Reel
29
PS212W subwoofer
LM5008
Pin Description
PIN 1 NAME SW Switching Node DESCRIPTION APPLICATION INFORMATION Power switching node. Connect to the output inductor, re-circulating diode, and bootstrap capacitor. An external capacitor is required between the BST and the SW pins. A 0.01µF ceramic capacitor is recommended. An internal diode charges the capacitor from VCC.
6
2
BST
Boost Pin (Bootstrap capacitor input)
3
RCL
Current Limit OFF time set pin Toff = 10-5 / (0.285 + (FB / 6.35 x 10- Ground pin
x RCL))
A resistor between this pin and RTN sets the off-time when current limit is detected. The off-time is preset to 35µs if FB = 0V. Ground for the entire circuit. This pin is connected to the inverting input of the internal regulation comparator. The regulation threshold is 2.5V. A resistor between this pin and VIN sets the switch on time as a function of VIN. The minimum recommended on time is 400ns at the maximum input voltage. This pin can be used for remote shutdown. If an auxiliary voltage is available to raise the voltage on this pin, above the regulation setpoint (7V), the internal series pass regulator will shutdown, reducing the IC power dissipation. Do not exceed 14V. This voltage provides gate drive power for the internal Buck switch. An internal diode is provided between this pin and the BST pin. A local 0.1µF decoupling capacitor is recommended. Series pass regulator is current limited to 10mA. Recommended operating range: 9.5V to 95V.
4 5
RTN FB
Feedback input from Regulated Output
6
RON/SD
On time set pin Ton = 1.25 x 10-10 RON / VIN
7
VCC
Output from the internal high voltage series pass regulator. Regulated at 7.0V.
LM5008
8
VIN
Input voltage
Typical Application Circuit and Block Diagram
20097901
F.
30
PS212W subwoofer
Philips Semiconductors Product specification
8-bit parallel-in/serial-out shift register
FEATURES · Asynchronous 8-bit parallel load · Synchronous serial input · Output capability: standard · ICC category: MSI GENERAL DESCRIPTION The 74HC/HCT165 are high-speed Si-gate CMOS devices and are pin compatible with low power Schottky TTL (LSTTL). They are specified in compliance with JEDEC standard no. 7A. The 74HC/HCT165 are 8-bit parallel-load or serial-in shift registers with complementary serial outputs (Q7 and Q7) available from the last stage. When the parallel load (PL) input is LOW, parallel data from the D0 to D7 inputs are loaded into the register asynchronously.
74HC/HCT165
When PL is HIGH, data enters the register serially at the Ds input and shifts one place to the right (Q0 Q1 Q2, etc.) with each positive-going clock transition. This feature allows parallel-to-serial converter expansion by tying the Q7 output to the DS input of the succeeding stage. The clock input is a gated-OR structure which allows one input to be used as an active LOW clock enable (CE) input. The pin assignment for the CP and CE inputs is arbitrary and can be reversed for layout convenience. The LOW-to-HIGH transition of input CE should only take place while CP HIGH for predictable operation. Either the CP or the CE should be HIGH before the LOW-to-HIGH transition of PL to prevent shifting the data when PL is activated. APPLICATIONS · Parallel-to-serial data conversion
QUICK REFERENCE DATA GND = 0 V; Tamb = 25 °C; tr = tf = 6 ns TYPICAL SYMBOL tPHL/ tPLH PARAMETER propagation delay CP to Q7, Q7 PL to Q7, Q7 D7 to Q7, Q7 maximum clock frequency input capacitance power dissipation capacitance per package notes 1 and 2 CONDITIONS HC CL = 15 pF; VCC = 5 V 16 15 11 56 3.5 35 14 17 11 48 3.5 35 ns ns ns MHz pF pF HCT UNIT
fmax CI CPD Notes
1. CPD is used to determine the dynamic power dissipation (PD in µW): PD = CPD × VCC2 × fi + (CL × VCC2 × fo) where: fi = input frequency in MHz fo = output frequency in MHz (CL × VCC2 × fo) = sum of outputs CL = output load capacitance in pF VCC = supply voltage in V 2. For HC the condition is VI = GND to VCC For HCT the condition is VI = GND to VCC - 1.5 V ORDERING INFORMATION See "74HC/HCT/HCU/HCMOS Logic Package Information".
31
PS212W subwoofer
Philips Semiconductors Product specification
8-bit parallel-in/serial-out shift register
PIN DESCRIPTION PIN NO. 1 7 9 2 8 10 11, 12, 13, 14, 3, 4, 5, 6 15 16 SYMBOL PL Q7 Q7 CP GND Ds D0 to D7 CE VCC NAME AND FUNCTION asynchronous parallel load input (active LOW) complementary output from the last stage serial output from the last stage clock input (LOW-to-HIGH edge-triggered) ground (0 V) serial data input parallel data inputs clock enable input (active LOW) positive supply voltage
74HC/HCT165
Fig.1 Pin configuration.
Fig.2 Logic symbol.
Fig.3 IEC logic symbol.
32
PS212W subwoofer
Philips Semiconductors Product specification
8-bit parallel-in/serial-out shift register
74HC/HCT165
Fig.4 Functional diagram.
FUNCTION TABLE OPERATING MODES PL parallel load L L H H H X X L L H CE X X X INPUTS CP X X l h X DS L H X X X D0-D7 L H L H q0 Qn REGISTERS Q0 Q1-Q6 L-L H-H q0-q5 q0-q5 q1-q6 L H q6 q6 q7 OUTPUTS Q7 H L q6 q6 q7 Q7
serial shift hold "do nothing" Note
1. H = HIGH voltage level h = HIGH voltage level one set-up time prior to the LOW-to-HIGH clock transition L = LOW voltage level I = LOW voltage level one set-up time prior to the LOW-to-HIGH clock transition q = lower case letters indicate the state of the referenced output one set-up time prior to the LOW-to-HIGH clock transition X = don't care = LOW-to-HIGH clock transition
Fig.5 Logic diagram.
33
PS212W subwoofer
CS4340
24-Bit, 96 kHz Stereo DAC for Audio
Features
l Complete Stereo DAC System: Interpolation,
Description
The CS4340 is a complete stereo digital-to-analog system including digital interpolation, fourth-order deltasigma digital-to-analog conversion, digital de-emphasis and switched capacitor analog filtering. The advantages of this architecture include: ideal differential linearity, no distortion mechanisms due to resistor matching errors, no linearity drift over time and temperature and a high tolerance to clock jitter. The CS4340 accepts data at audio sample rates from 2 kHz to 100 kHz, consumes very little power, and operates over a wide power supply range. The features of the CS4340 are ideal for DVD players, CD players, set-top box and automotive systems.
D/A, Output Analog Filtering l 101 dB Dynamic Range l 91 dB THD+N l Low Clock Jitter Sensitivity l +3 V to +5 V Power Supply l Filtered Line Level Outputs l On-Chip Digital De-emphasis for 32, 44.1, and 48 kHz l 30 mW with 3 V supply l Popguard® Technology for Control of Clicks and Pops
ORDERING INFORMATION CS4340-KS 16-pin SOIC, -10 to 70 °C CS4340-BS 16-pin SOIC, -40 to 85 °C CDB4340 Evaluation Board
I
SCLK/DEM1 RST
DEM0
MUTEC External Mute Control DAC Analog Filter AOUTL
De-emphasis Interpolation Filter Interpolation Filter
LRCK SDATA
Serial Input Interface
DAC
Analog Filter
AOUTR
DIF0 DIF1
MCLK
Preliminary Product Information
P.O. Box 17847, Austin, Texas 78760 (512) 445 7222 FAX: (512) 445 7581 http://www.cirrus.com
This document contains information for a new product. Cirrus Logic reserves the right to modify this product without notice.
Copyright © Cirrus Logic, Inc. 2000 (All Rights Reserved)
34
NOV `00 DS297PP3 1
PS212W subwoofer
CS4340
3. PIN DESCRIPTION
Reset Serial Data Left/Right Clock Master Clock Digital Interface Format Digital Interface Format De-emphasis RST SDATA LRCK MCLK DIF1 DIF0 DEM0
1 2 3 4 5 6
7
16 15 14 13 12 11
10
MUTEC AOUTL VA AGND AOUTR VQ FILT+
Mute Control Left Analog Output Analog Power Analog Ground Right Analog Output Quiescent Voltage Positive Voltage Reference
Serial Clock / De-emphasis SCLK/DEM1
REF_GND Reference Ground
8
9
RST
1
Reset (Input) - The device enters a low power mode and all internal state machines are reset to the default settings when low. RST should be held low during power-up until the power supply, master and left/right clocks are stable. Serial Audio Data (Input) - Two's complement MSB-first serial data is input on this pin. The data is clocked into SDATA via the serial clock and the channel is determined by the Left/Right clock. The required relationship between the Left/Right clock, serial clock and serial data is defined by the DIF1-0 pins. The options are detailed in Figures 16-19. Serial Clock (Input) - Clocks the individual bits of the serial data into the SDATA pin. The required relationship between the Left/Right clock, serial clock and serial data is defined by the DIF1-0 pins. The options are detailed in Figures 16-19. The CS4340 supports both internal and external serial clock generation modes. Internal SCLK mode is used to gain access to extra de-emphasis modes. Internal Serial Clock Mode - In the Internal Serial Clock Mode, the serial clock is internally derived and synchronous with the master clock and left/right clock. The SCLK/LRCK frequency ratio is either 32, 48, or 64 depending upon the DIF1-0 pins as shown in Figures 16-19. Operation in this mode is identical to operation with an external serial clock synchronized with LRCK. External Serial Clock Mode - The CS4340 will enter the External Serial Clock Mode whenever 16 low to high transitions are detected on the SCLK pin during any phase of the LRCK period. The device will revert to Internal Serial Clock Mode if no low to high transitions are detected on the SCLK pin for 2 consecutive periods of LRCK.
SDATA
2
SCLK
3
35
PS212W subwoofer
STM809, STM810 STM811, STM812
Reset Circuit
FEATURES SUMMARY
PRECISION MONITORING OF 3V, 3.3V, and 5V SUPPLY VOLTAGES TWO OUTPUT CONFIGURATIONS Push-pull RST Output (STM809/811) Push-pull RST Output (STM810/812) 140ms RESET PULSE WIDTH (MIN) LOW SUPPLY CURRENT - 6µA (TYP) GUARANTEED RST/RST ASSERTION DOWN TO VCC = 1.0V OPERATING TEMPERATURE: 40°C to 85°C (Industrial Grade) LEAD-FREE, SMALL SOT23 and SOT143 PACKAGE
Figure 1. Packages
SOT23-3 (WX)
Table 1. Device Options
ActiveLow RESET STM809 STM810 STM811 STM812 ActiveHigh RESET Manual RESET Input Package SOT23-3 SOT23-3 SOT143-4 SOT143-4
SOT143-4 (W1)
November 2004
1/18
36
PS212W subwoofer
STM809/810/811/812
SUMMARY DESCRIPTION
The STM809/810/811/812 MICROPROCESSOR RESET Circuits are low-power supervisory devices used to monitor power supplies. They perform a single function: asserting a reset signal whenever the VCC supply voltage drops below a preset value and keeping it asserted until VCC has risen above the preset threshold for a minimum period of time (trec). The STM811/812 also provide a push-button reset input (MR).
Figure 2. Logic Diagram (STM809/810)
VCC
Table 2. Signal Names
VSS RST RST(1) Ground Active-Low RESET Output Active-High RESET Output Supply Voltage Manual Reset Input
STM809/810
RST (RST)(1)
VCC MR(2)
Note: 1. STM810/812 only 2. STM811/812 only
VSS
Note: 1. For STM810
AI07832
Figure 4. SOT23-3 Connections
VSS RST (RST) 1 2
3
VCC
Figure 3. Logic Diagram (STM811/812)
VCC
(For STM810)
AI07833
Figure 5. SOT143-4 Connections
MR STM811/812 RST (RST)
(1)
VSS RST (RST)
1 2
4 3
VCC MR
(For STM812) VSS
Note: 1. For STM812
AI07834 AI07831
Figure 6. Block Diagram
VCC VRST COMPARE trec Generator MR(1)
DEBOUNCE
AI07835
RST(2)
Note: 1. STM811/812 only 2. RST for STM810/812
4/18
37
DO4918
PS212W subwoofer
Squeak 1.5 WHAM2 [WH4924 WH4931]
HighPerformance 2.4 GHz Digital Wireless Audio Solution
FEATURES
· · · · · · · · · · · · Analog or Digital Audio Input/Output 48 kHz, 16-bit digital, stereo audio transmission Digital volume control, manual mute Auto mute (when signal lost), digital noise gate 2.4 GHz wireless at 1.536 Mbps Robust Quality of Service (QoS) Advanced error protection protocols with hardware forward error correction, adaptive frequency hopping, and walking frequency diversity 25 or 50 meter indoor range Up to 6 transmitters in specified range area Low latency; firmware selectable 15 64 ms Duplex utility control channel at 1.5 kbps Programmable for custom features (with development kit)
GENERAL DESCRIPTION
The Squeak 1.5 WHAM2 (Wireless HiFi Audio Module) is a highly integrated module package that provides a complete solution for wireless audio. Squeak 1.5, using the Micro Linear ML2724 radio transceiver front end and the XInC2 wireless processor, is ideal for high performance wireless audio applications such as home theater, stereo and outdoor speakers, and microphones. Squeak 1.5 is available in either a 25 or 50 meter indoor range WHAM2 module. The WHAM2 digitizes a 2-channel stereo input signal, sends it across a robust 2.4 GHz radio frequency link, and converts the signal back to a stereo analog signal for use at a remote location. WHAM2 is also available with a Digital Audio Serial Interface (DASI) port that can be configured to interface with any SPI supporting device (I2S, left- or right-justified), including ADCs, DACs, digital audio streams such as S/P-DIF or USB. A development kit is required to modify the DASI port and/or to modify application source code firmware.
ORDERING INFORMATION
25 meter TX WH4924 Analog I/O RX WH4925 TX WH4926 Digital I/O RX WH4927 2-node EV4931 Evaluation Kit Add-on node EV4933 Upgrade from any eval. kit Dev. Kit 50 meter WH4928 WH4929 WH4930 WH4931 EV4937 EV4939 DK4909
BLOCK DIAGRAM
DO4918 -- Squeak 1.5 WHAM2 Preliminary Datasheet (rev. 3.0) 2006-04-06 Copyright © 2006 Eleven Engineering Inc. (all rights reserved)
38
Page 1 of 47
PS212W subwoofer
WHAM2 Receiver Pinout
Pin#
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18
25
1
Pin Name
RFVCC RFGND GND VCC /RESET PB1 MISO0/ PG0 MOSI0/ PG1 SCK0/ PG2 PF0/ SDIO1 PF1/ SDIO2 PC7 PC6 PC5 PC4 PC0/ MCLK PC1/ AN2 PI0/ BB1CLK/ AN1 PI1/ BB1O/ LRCK PI2/ BB1I AGND AOUTR/ SDIO0 AOUTL/ BCLK AGND AVDD
Analog I/O Default
RFVCC RFGND GND VCC /RESET PB1 MISO0 MOSI0 SCK0 PF0 PF1 PC7 PC6 PC5 PC4 PC0 PC1 PI0
Digital I/O Default
RFVCC RFGND GND VCC /RESET PB1 MISO0 MOSI0 SCK0 PF0 PF1 PC7 PC6 PC5 PC4 MCLK PC1 PI0
Description
RF Voltage Power Input RF Ground Digital Ground Digital Power Input Reset input (active low) SPI0 Chip Select (CS0) PB1 SPI0 Master Data Input MISO0 (FW default), or GPIO port PG0 SPI0 Master Data Output MOSI0 (FW default), or GPIO port PG1 SPI0 Clock output SCK0 (FW default), or GPIO port PG2 General Purpose IO port PF0 (FW default), or Digital Audio Serial Interface1 (DASI) General Purpose IO port PF1 (FW default), or Digital Audio Serial Interface2 (DASI) General Purpose IO port PC7 General Purpose IO port PC6 General Purpose IO port PC5 General Purpose IO port PC4 General Purpose IO port PC0, or MCLK output General Purpose IO port PC1 (HW default), or XInC2 ADC Analog Input #2 General Purpose IO port PI0 (HW & FW default), or Baseband Unit1 Clock, or XInC2 ADC Analog Input #1 General Purpose IO PI1, or Baseband Unit1 Output, or Left-Right Clock (LRCK) General Purpose IO PI2 (HW & FW default), or Baseband Unit1 Input Analog Ground Audio line-out for Right Channel AOUTR, or Serial DASI Data input/output SDIO0 Audio line-out for Left Channel AOUTL, or Serial DASI Bit Clock output BCLK Analog Ground Analog Power Input
19
PI1 LRCK PI2 GND SDIO0 AOUTL AGND AVDD BCLK GND (no connect)
20 21 22 23 24 25
PI2 AGND AOUTR
Table 6 WHAM2 RX Pinouts
39
PS212W subwoofer
1.4 ADVANCED PINOUT CONFIGURATION
The WHAM2 pinout can be configured differently than above for certain applications. This customization can be performed at the time of production or during product assembly. The following two diagrams and two tables describe how to configure the WHAM2 for different operations by changing jumpers and components on the modules themselves.
Figure 1 WHAM2 Transmitter DM Layout
Figure 2 WHAM2 Receiver DM Layout
40
PS212W subwoofer
WHAM2 RX Jumpers and Options
Pin Name
Edge pin-16
Jumpers/ Components
J3 = 0R J4 = DNP J3 = DNP J4 = 0R J5 = 0R J6 = DNP J5 = DNP J6 = 0R J7 = 0R J8 = DNP J7 = DNP J8 = 0R J9 = 0R J10 = DNP J9 = DNP J10 = 0R J17, J18 = DNP U5 = CS4341, R19, R20 = 10K, R23 = 47K, R25, R27 = 100R, R26 = 0R, C7 = 1uF, C9, C13 = 10uF, C12, C14 = 8200pF, C22, C30, C31 = 0.1uF, C33 = 470pF. J17, J18 = 0R U5 = DNP, R19, R20, R23 = DNP, R25-R27 = DNP, C7 = DNP, C9, C13 = DNP, C12, C14 = DNP, C22, C30, C31 = DNP, C33 = DNP
Pin Function
Pin 16 is GPIO port pin PC0 (FW configurable as input or output.) Pin 16 is MCLK (output) (FW programmable frequency: typically 12.288, 24.576, or 49.152 MHz.) Pin 17 is GPIO port pin PC1 (FW configurable as input or output) Pin 17 is AN2 (XInC2 muxed analog input #2.) (Input voltage range of ADC is 0V to 1.8V.) Pin 18 is FW selectable as either GPIO port pin PI0 or baseband unit #1 clock pin BB1CLK. (PI0 is FW configurable as input or output.) Pin 18 is AN1 (XInC2 muxed analog input #1.) (Input voltage range of ADC is 0V to 1.8V.) Pin 19 is FW selectable as either GPIO port pin PI1 or baseband unit #1 data input/output pin BB1O. (PI1 is FW configurable as input or output.) Pin 19 is Left-Right Clock pin LRCK (output) Pin 22 is Right channel Analog Audio Output: AOUTR Pin 23 is Left channel Analog Audio Output: AOUTL
WH4925/29 WH4927/31
Default config. Default config.
Edge pin-17
Edge pin-18
Edge pin-19
Edge pins 22 & 23
Pin 22 is serial digital data I/O port pin SDIO0 Pin 23 is Serial digital audio clock SCLK
Table 8 WHAM2 RX Jumper Configurations
41
PS212W subwoofer
42
PS212W subwoofer
Green
D401 LED_5DIA
Red
43
PS212W subwoofer
9
U106:C TL074
8
13 12
U106:D TL074
14
10
U106:B TL074
7
6 5
U106:A TL074
1
2 3
U106:E
VDD
P106
U106:F
VEE
44
PS212W subwoofer
U105:D
VEE
U105:C
VDD
2 3
U105:A TL072
1
6 5
U105:B TL072
7
45
PS212W subwoofer
2 1 3
U108:A TL-072 U101:B TL-072
7 5 9 10
U102:C TL074
8
13 12
U102:D TL074
14 2 3
U101:A TL-072
1
6
2
U103:A TL-072
1
6 5
U102:B TL074
7
U102:A 2 TL074
1 3 5 6
U103:B TL-072
7
3
U108:C
VDD
U101:C
VDD
U102:E
VDD
U103:C
VDD
6 5
U108:B TL-072
7
U101:D
VEE
U102:F
VEE
U103:D
VEE
U108:D
VEE
46
PS212W subwoofer
C318 100P R317 5K1 R319 5K1
JK1
6 5
U109:B TL-072
7
C311 10u R330 10K
U109:C
VDD
R332 C327 100u 220R
R320 5K1 R321 5K1 C312 22u
C332 100P C319 100P R316 5K1
C320 104z
C322 U109:D 104z
VEE
C328 100u
R333 220R
R318 5K1
2 1 3
C310 10u R331 10K
R314 100R C304 220P R315 100R C305 220P
R300 6K8
R322 5K1
R323 5K1
U109:A C331 TL-072 100P
R301 6K8
47
PS212W subwoofer
L01 56R
48
1
2
PS212W subwoofer
R505 C503 10R-1/4W-MO .1/100V C501 47u/100V
P501
U501 C505 D501 L501 LM5008 103 10BQ100220u
1
C506 C507 L502 470u .1 22u C508 470u
R501 330K C104 100n R502 270K
R503 120R-1%
2
R504 240R-1%
P502
49
PS212W subwoofer
50
PS212W subwoofer
51
PS212W subwoofer
52
PS212W subwoofer
53
PS212W subwoofer
54