Text preview for : Infinity-TSS4000 actsub.pdf part of Infinity TSS4000 active subwoofer
Back to : Infinity-TSS4000 actsub.p | Home
TSS-SUB4000
SERVICE MANUAL
Infinity Systems Incorporated
250 Crossways Park Dr.
Woodbury, New York 11797 Rev0 3/2005
TSS-SUB4000
CONTENTS
BASIC SPECIFICATIONS . . . . . . . . . .................................................1
DETAILED SPECIFICATIONS . . . . . . . . . . . ........................................2
CONTROLS. ....................... .. . .......................................... . . . . . . .4
CONNECTIONS . . . . . . . . . . . .................................................... . . . 5
OPERATION....... . . . . .. . . . . . . . .. .. . . . .. .. . . . . ............. . . ... . . . . . . .6
EXPLODED VIEWS-MECHANICAL PARTS LIST....... . ... . .. . . .. . ... . ....7
TEST SET-UP & PROCEDURE............................. .. .. . . ................. .9
BLOCK DIAGRAM. . . . ..................... ....................................... . ... . 10
TROUBLESHOOTING FLOW CHART..................................................11
SERVICE NOTE - POWER TRANSFORMER.....................................12
ELECTRICAL PARTS LIST ........................ ......................................13
PCB DRAWINGS. . . ..................... ..................................................17
IC TRANSISTOR PINOUTS . ... . . .. . . . . . .................................. . . . 20
SCHEMATIC DIAGRAMS (120v). . ................................................... . .21
PACKAGING. ....................... .. . ......... .............................. . . . . . . 31
SPECIFICATIONS
Frequency Response 28Hz 150Hz (3dB)
24Hz 180Hz (6dB)
Maximum Amplifier Output 400 watts RMS
(20Hz 150Hz with no more than 0.1% THD)
Crossover Frequency 150Hz, 12dB/octave
Driver 12" (305mm) MMD®
Dimensions (H x W x D) 17-1/2" x 17-1/4" x 11-1/8"
(445mm x 438mm x 283mm)
Weight 48 lb (21.8kg)
Infinity continually strives to update and improve existing products, as well as create new ones. The specifications and
construction details in this and related Infinity publications are therefore subject to change without notice.
1
TSS-SUB4000
TSS-4000 subwoofer 300W Powered Sub/ Plate Amp
LINE VOLTAGE Yes/No Hi/Lo Line Nom. Unit Notes
US 120vac/60Hz Yes 108-132 120 Vrms Normal Operation
EU 230vac/50-60Hz No 207-264 230 Vrms Normal operation, MOMS required
Asia 100vac/50Hz No 90-110 100 Vrms Normal Operation
QA Test
Parameter Specification Unit Conditions Notes
Limits
Amp Section
Type (Class AB, D, other) D ---
Load Impedance (speaker) 4 Ohms Nominal Z-curve required
Rated Output Power 300 Watts Regulated 120 V line 5% tollerance applies
THD@ Rated Power 1 % 22k filter, 50Hz 300W +/- 5%
THD @ 1 Watt 0.5 % 22k filter, 50Hz
DC Offset undefined mV-DC < 20 @ Speaker Outputs
Damping factor 20 N/A > 15 measured at 50 Hz
Input Sensitivity
Line/Hi Level Input Phase N/A
Line Input 370 mV mVrms 300 W @ 50Hz 1 input driven
Speaker/Hi Level Input N/A
Signal to Noise
SNR-A-Weighted 100 dBA relative to rated power A-Weighting filter
SNR-unweighted 70 dBr relative to rated power 22k filter
SNR rel. 1W-unweighted 60 dBr relative to 1W Output 22k filter
Volume @max, using RMS
Residual Noise Floor 2 mVrms
reading DMM/VOM (or A/P)
Volume @max, w/ A/P Swept
Residual Noise Floor 1 mVrms(max) Bandpass Measurement (Line
freq.+ harmonics)
Input Impedance
Line Input 10 k ohms Nominal
Speaker/Hi Level Input N/A
Active Filters
Low Pass (fixed or
FIXXED --
variable)
Frequency 130 Hz
Slope 24 dB/Octave
Q Butterworth --
Subsonic filter (HPF) fixed --
Frequency 35 Hz
Slope 12 dB/Octave
Q 1.2 --
Line Out Filter (HPF) NONE --
Frequency Hz
Slope dB/Octave
Q --
Friend Circuit FIXXED --
Frequency 66 Hz Hz notch filter
Slope 6 dB/Octave
Q 1.2 --
Video Boost NONE --
Boost dB
Range Hz
Special filter RABOS --
Switches
Main Power ON/OFF YES --
Type rocker -- Located on amp plate TV-5
Rabos ON/OFF YES --
Type mini togle -- Located on amp plate
Polarity Switch YES -- "Off": 0°; "On": 180°
Type mini togle -- Located on amp plate
Limiter (yes/no) YES compressor and limiter
2
TSS-SUB4000
QA Test
Parameter Specification Unit Conditions Notes
Limits
THD at Max. Output Power less than 10 % Maximum Output Power Maximum THD as a result of limiting.
Output Volume Control
Volume Control Pot YES -- mounted on amp panel
Detent (center/#) NO --
Taper (lin/log) log A taoer --
@ minimum setting no output
Input/Output Phase
Line Input vs. Hi Input N/A °
Lo/Hi Input vs. Lo/Hi Output N/A °
Input/Output
Line In (L,C,R,AC3,Mono) Stereo -- RCA phono jack, gold plated
LFE In YES -- Shared with "R" Line In jack
Signal Sensing (ATO)
Auto-Turn-On (yes/no) YES --
ATO Input Test Frequency 100 Hz
ATO Input Threshold 2 mV typ. LPF "On", BOS "Off"
ATO Low Pass cutoff 400 Hz 450 ATO-LPF for noise immunity LPF "On", BOS "Off"
Amp connected and AC on,
ATO Turn-on time 1 ms 10 then input signal applied ( 1 W
output )
Time before muting, after signal
Auto Mute / Turn-OFF Time 10 minutes 5 < t < 15
is removed
Power on Features
Power on Delay time greater than 2 sec. AC Power Applied
Bi-color LED located on front of
Power on LED YES --
cabinet
Normal On/Off green / red color ATO mode only
ATO -- color "Active": green; "Standby": red
Transients/Pops
ATO Transient 5 mV-peak @ Speaker Output
Turn-on Transient 30 mV-peak @ Speaker Output AC Line cycled from OFF to ON
Turn-off Transient 30 mV-peak @ Speaker Output AC Line cycled from ON to OFF
Efficiency
Stand-by Input Power 10 Watts typ. @ nom. line voltage
AC Power Cons.@1W 12 Watts typ. @ nom. line voltage
Power Cons.@rated power 473 Watts typ. @ nom. line voltage Input power measured is REAL Watts, not VA
Efficiency 63 % typ. @ nom. line voltage
Protection
Short Circuit Protection YES -- Direct short at output
Thermal Protection YES -- threshold ~ 65 deg. C at panel
DC present at Speaker Out
DC Offset Protection YES -- Relay for driver/fire protection
leads
Line Fuse Rating ( 120 V ) 3.15 Amps Type ADL or MDL Fuse holder on inside surface of amp panel
AC Power & Transformer
Double insulated cord,
Power cord length 9 feet
AWG#18
3
TSS-SUB4000
CONTROLS AND CONNECTIONS
Rear Panel
¡
TM
£
¢
§
¶
·
ª
¡ Subwoofer Level (Volume) Control Room Adaptive Bass Optimization System Controls (see page 5)
TM Line-Level Inputs § R.A.B.O.S. Selector
£ Normal/LFE Low-Pass Selector ¶ R.A.B.O.S. Level Adjustment
¢ Phase Switch · R.A.B.O.S. Bandwidth Adjustment
Power Switch ª R.A.B.O.S. Center-Frequency Adjustment
TSS-SUB4000
4
TSS-SUB4000
CONNECTIONS
If you have a Dolby* Digital or DTS® receiver/processor If your receiver/processor has subwoofer
with a low-frequency-effects (LFE) output: outputs for the left and right channels:
· Set Low-Pass Switch to Off. · Set Low-Pass Switch to On.
NOTE: In this case, you do not need to use a Y connector. Simply NOTE: Some receivers have a single subwoofer output (do not confuse
connect the LFE output on your receiver/processor to either the this with a single LFE output as described to the left). In that case,
left or right input on the subwoofer. it is recommended that you use a Y connector (not included) to maximize
performance.
TSS-SUB4000
5
TSS-SUB4000
OPERATION
Power On Low-Pass Selector
Plug your subwoofer's AC cord into a wall outlet. Do not use the If you have a Dolby Digital or DTS processor/receiver, the
outlets on the back of the receiver. Crossover Frequency is set by the processor/receiver. Consult
Initially set the Subwoofer Level (Volume) Control ¡ to the your owner's manual to learn how to view or change this setting.
"min" position. In this case, the Low-Pass Selector £ should be set to "Off".
We strongly recommend this setup method.
Turn on your sub by pressing the Power Switch on the
rear panel. When this switch £ is in the "On"position, the subwoofer will
reproduce frequencies below 150Hz.
Auto On/Standby
With the Power Switch in the ON position, the Power Phase Control
Indicator LED on the front of the subwoofer will remain backlit in The Phase Switch ¢ determines whether the subwoofer
red or green to indicate the On/Standby mode of the subwoofer. speaker's piston-like action moves in and out with the main
RED = STANDBY (No signal detected, Amp Off) speakers, 0,° or opposite the main speakers, 180°. Proper phase
GREEN = ON (Signal detected, Amp On) adjustment depends on several variables such as room size,
subwoofer placement and listener position. Adjust the phase
The subwoofer will automatically enter the Standby mode after
switch to maximize bass output at the listening position.
approximately 10 minutes when no signal is detected from your
system.The subwoofer will then power ON instantly when a
signal is detected. During periods of normal use, the Power
Switch can be left on.You may turn off the Power Switch
for extended periods of nonoperation, e.g., when you are away
on vacation.
Adjust Gain
Turn on your entire audio system and start a CD or movie
soundtrack at a moderate level.Turn up the Subwoofer Level
(Volume) Control ¡ about halfway. If no sound emanates from
the subwoofer, check the AC-line cord and input cables. Are the
connectors on the cables making proper contact? Is the AC
plug connected to a "live" receptacle? Has the Power Switch
been pressed to the "On" position? Once you have confirmed that
the subwoofer is active, proceed by playing a CD, record or
cassette. Use a selection that has ample bass information.
Set the overall volume control of the preamplifier or stereo to a
comfortable level. Adjust the Subwoofer Level (Volume) Control ¡
until you obtain a pleasing blend of bass. Bass response should
not overpower the room but rather should be adjusted so there
is a harmonious blend across the entire musical range. Many
users have a tendency to set the subwoofer volume too loud,
adhering to the belief that a subwoofer is there to produce lots
of bass.This is not entirely true. A subwoofer is there to enhance
bass, extending the response of the entire system so the bass
can be felt as well as heard. However, overall balance must
be maintained or the music will not sound natural. An
experienced listener will set the volume of the subwoofer so
its impact on bass response is always there but never obtrusive.
6
TSS-SUB4000
TSS-SUB4000 EXPLODED VIEW
Ref # Description Part Number Qty
1 Grille 329-120-05097-0VA 1
2 Woofer/Trim Ring Screw 351-AM04030A893 8
3 Trim Ring 213-120-05033-0BA 1
4 Woofer 12" (305mm) MMD 30PR14BW-DW01 1
5 Port Tube 249-HIPS-05021-0VA 1
6 TSS-SUB4000 Amplifier Not for Sale 1
7 Amplifier Screw 352-FM04020D605 12
8 TSS-SUB4000 Cabinet Not for Sale 1
9 Rubber Foot 320-RUB-05030-0BA 4
10 Foot Screw 352-CM04025D604 4
11 Gasket 333-EVA-05091-0WA 1
12 LED 166-A055A8GX 1
13 Plastic Plate Not Serviceable 1
14 Aluminum Plate Not Serviceable 1
Not Power Transformer 150-R1107008 1
Shown
7
TSS-SUB4000
Ref # Description Part Number Qty
1 Screw 352-CM03530D926 11
2 Damping 1
3 Main Mounting Bolt 1
4 Tube Gasket 2
5 Rubber 398-RUB-05093 1
6 Gasket 2
7 Rubber Gasket 336-RUB-05013 1
8 Damping 1
9 Power Transformer 150-R1107008 1
10 Nut 1
11 Damping 1
8
TSS-SUB4000
TSS-SUB4000 Test Set Up and Procedure
SYSTEM AURAL SWEEP TEST
Equipment needed:
· Function/signal generator/sweep generator
· Multimeter
· RCA cables
General Unit Function (UUT = Unit Under Test)
Switches/knobs on the amplifier faceplate:
Phase switch either position
Low Pass switch Off
RABOS switch Off
1. From the signal generator, Connect both right and left line level inputs (RCA jacks) to signal generator and
UUT. Use Y-cable if necessary from mono source.
2. On the amplifier, turn the LEVEL control full Counterclockwise (Min).
3. Turn on generator, adjust to 125mV, 50 Hz.
4. Plug in UUT; turn the power switch ON. Turn LEVEL control full Clockwise (Max).
5. LED (on front panel) should now be Green; immediate bass response should be heard and felt from rear port
tube opening.
Sweep Function
1. Follow steps 1-5 above, using a sweep generator as a signal source.
2. Sweep generator from 20Hz to 1kHz. Listen to the cabinet and drivers for any rattles, clicks, buzzes or
any other noises. If any unusual noises are heard, remove woofer and test.
Driver Function (Woofer)
1. Remove woofer from cabinet (follow steps on exploded view page); detach + and - wire clips.
2. Check DC resistance of woofer; it should be 3.5 ohms±10%.
3. Connect a pair of speaker cables to driver terminals. Cables should be connected to an integrated
amplifier fed by a signal generator. Turn on generator and adjust so that speaker level output is 5.0V.
4. Sweep generator from 20Hz to 1kHz. Listen to driver for any rubbing, buzzing, or other unusual noises.
9
TSS-SUB4000
10
TSS-SUB4000
TSS-Sub4000 Testing Flow Chart
Start yes
Test protection
Dc voltage check
±Vcc,±15V no Check U107.R237
OK
±15Vcc ect
no Check transformer yes
OK C168,C169,D123,
Test limiter circuit
D124,C170
yes
Power on check no Check U106.Q107ect
OK
LED red &blue
yes
Check vol module
no Check THD output
& connector
OK power, noise
cable& ±15V.ect
yes
no Check pre board
Test frequency OK & power board ,
Response yes ±Vcc,±15V ect
no Auto off Function
Check U102,R124,
Hi pot test
OK C104,R125,C117.ect
yes no Check U103.Q101.
Q102.C131.R142;Ac
Test phase sw,low OK
cord, Transformer.
pass sw rabos vr
yes
Listening test
no
Check sw103,102, no
OK
R158,163,177 ect
OK
yes
Test input sensitivity yes
The Amp ass'y ok
no END
Check U101,R117,
OK
R112,R114 ect
11
TSS-SUB4000
NOTICE
The main power transformer (toroid) part# 150-r1107008 in the TSS-SUB4000 is
not mounted in the amplifier inside the amp cover, but mounted in the cabinet in a
separate location.
Replacement:
To replace the power transformer, it is necessary to remove the woofer from the cabinet.
The mounting bolt and transformer itself is mounted on an internal brace; both are
accessible through the woofer opening. Instructions for woofer removal can be found on
the exploded view, page 7.
Troubleshooting:
To keep the circuit "live" while exposing the amplifier components, the amplifier cannot
completely be removed and powered up outside the cabinet due to the power
connections to the externally mounted transformer. Instead, an alternate method is to
leave the amp cover in place and remove the four Phillips screws holding the amp ass'y
to the amp cover. Then the amplifier can be partially removed for access, while
maintaining the power connections. Unplugging the LED connection (red/black wires) at
the PCB plug will allow the amp to be removed even further.
12
TSS-SUB4000
TSS-SUB4000 120V Electrical Parts List
Part Number Description Qty Reference Designator
MAIN PCB
Resistors
110-12621j15 Resistor 6201/2W ± 5% 15mm 1 R238
110-16102j26 Resistor 1K 1/6W ± 5% CF 26mm 3 R210,R239,R264
110-16103j26 Resistor 10K 1/6W ± 5% CF 26mm 9 R227,229,230,231,232,233,260,261,263
110-16153j26 Resistor 15K 1/6W ± 5% CF 26mm 2 R247,R249
110-16182j26 Resistor 1.8K 1/6W ± 5% CF 26mm 1 R248
110-16222j26 Resistor 2.2K 1/6W ± 5% CF 26mm 2 R242,R245
110-16223j26 Resistor 22K 1/6W ± 5% CF 26mm 3 R218,R220,R223
110-16274j26 Resistor 270K 1/6W ± 5% CF 26mm 1 R240
110-16333j26 Resistor 33K 1/6W ± 5% CF 26mm 1 R211
110-16391j26 Resistor 3901/6W CF 26mm 2 R243,R246
110-16432j26 Resistor 4.3K 1/6W ± 5% CF 26mm 1 R254
110-16472j26 Resistor 4.7K 1/6W ± 5% CF 26mm 4 R217,219,222,213
110-16473j26 Resistor 47K 1/6W ± 5% CF 26mm 1 R221
110-16683j26 Resistor 68K 1/6W ± 5% CF 26mm 1 R212
122-14101j26 fusible Resistor 1/4W 100ohm 5% 2 R241,R244
116-141r00j26x metal film Resistor 1.001/4W ± 5% MO 26mm 2 R256,R255
116-161001f26 metal film Resistor 1K 1/6W ± 1% MF 26mm 2 R252,R253
116-161002f26 metal film Resistor 10K 1/6W ± 1% MF 26mm 2 R234,R235
116-161022f26 metal film Resistor 10.2K 1/6W MF 26mm 1 R251
116-161301f26 metal film Resistor 1.30K 1/6W MF 26mm 3 R226,R228,R236
116-161822f26 metal film Resistor 18.2K 1/6W ± 1% MF 26mm 1 R214
116-162001f26 metal film Resistor 2.00K 1/6W ± 1% MF 26mm 1 R215
116-162492f26 metal film Resistor 24.9K 1/6W ± 1% MF 26mm 2 R257,R258
116-164320f26 metal film Resistor 432 1/6W ± 1% MF 26mm 1 R265
116-166813f26 metal film Resistor 681K 1/6W ± 1% MF 26mm 1 R262
110-20152j20 Resistor 1.5K 2W ± 5% CF 20mm KINK 1 R208
113-500r1j10 cement Resistor 0.15W ± 5% 2 R224,R225
116-142003f26 metal film Resistor 200K 1/4W ± 1% MF 26mm 1 R209
Capacitors
130-2b102k503 disc Capacitor 1000P 50V ± 10% 1 C165
130-3f104z503 disc Capacitor 0.1U 50V +80/-20% 2 C163,C164
130-ch101j503 disc Capacitor 100P 50V ±5% 2 C159,C160
135-3107m16 electrolytic Cap 100uF 16V ±20% 2 C166,C167
135-3226m50 electrolytic Cap 22U 50V ±20% 2 C161,C162
135-3227m10 electrolytic Cap 220U 10V ±20% 2 C156,C157
139-3227m16 low leakage ec 220uF 16V ± 20% 1 C155
140-rx103ka03 multylayer Cap 10nF 100V X7R 10% 1 C174
140-rx473kb03 multylayer Cap 47nF 200V X7R ± 10% 2 C172,C173
135-4228m35 electrolytic Cap 2200uF 35V ± 20% 2 C170,C171
135-4688m80 electrolytic Cap 6800U 80V ± 20% 2 C168,C169
Semiconductors
190-161431c1p1 IC TL431CLP Shunt Regulator 1 D115
192-027c1815gr Transistor 2SC1815GR NPN 4 Q110,112,114,117
192-028a1015gr Transistor 2SA1015GR PNP 3 Q111,113,115
192-1572n5551 Transistor FSC 2N5551 NPN 1 Q109
192-1582n5401 Transistor FSC 2N5401 AI-PNP 350V 500mA TO-92 1 Q108
197-031n4148 diode 100mA 75V SIGNAL IN4148 ROHM 7 D118,119,120,121,125,126,117
199-15000565 ZENER diode 5.6V 1/2W 52mm 1 D116
199-15001505 ZENER diode 15V 1/2W 52mm 1 D122
199-15002005 ZENER diode 20V 1/2W 52mm 1 D129
192-991d669a Transistor HI-SINCERITY HSD669A NPN 1 Q116
192-992b649t Transistor HSB649T PNP 1 Q118
190-161m324n I.C.LM324N QUAD OP-AMP 1 U107
197-00db103g diode 1A 200V DF02M DB103G BRIDGE 1 D124
197-00kbu1003 diode 10A 200V KBU1003 BRIDGE 1 D123
197-101n4002 diode 1N4002 1 D114
13
TSS-SUB4000
Part Number Description Qty Reference Designator
MAIN PCB
Miscellaneous
109-1tsc103j0 thermister TSC05103J 1 R237
162-10229004 wire assy 220mm AWG28 1 P107
171-udhss124d relay 5A 24V UDH-SS124D 1 K101
175-1c02p01 coupling 2PIN PITCH=2.5mm 1 P108
175-1c06v01 coupling 6PIN PITCH=2.5mm 1 P105
175-1d02v01 coupling 2PIN PITCH=3.96mm 1 P112
INPUT/RABOS PCB
Resistors
110-14152j26 Resistor 1.5K 1/4W ± 5% CF 26mm 1 R150
110-16101j26 Resistor 1001/6W ± 5% CF 26mm 4 R112,R113,R151,R152
110-16102j26 Resistor 1K 1/6W ± 5% CF 26mm 2 R140,R196
110-16103j26 Resistor 1K 1/6W ± 5% CF 26mm 9 R118,126,129,133,136,146,149,199,156
110-16105j26 Resistor 1M 1/6W ± 5% CF 26mm 2 R145,R181
110-16106j26 Resistor 10M 1/6W ± 5% CF 26mm 1 R186
110-16151j26 Resistor 1501/6W ± 5% CF 26mm 1 R139
110-16154j26 Resistor 150K 1/6W ± 5% CF 26mm 1 R138
110-16183j26 Resistor 18K 1/6W ± 5% CF 26mm 1 R147
110-16203j26 Resistor 20K 1/6W ± 5% CF 26mm 1 R200
110-16221j26 Resistor 2201/6W ± 5% CF 26mm 2 R119,R120
110-16223j26 Resistor 22K 1/6W ± 5% CF 26mm 2 R141,R148
110-16472j26 Resistor 4.7K 1/6W ± 5% CF 26mm 1 R144
110-16473j26 Resistor 47K 1/6W ± 5% CF 26mm 1 R137
110-16474j26 Resistor 470K 1/6W ± 5% CF 26mm 1 R143
110-164r7j26 Resistor 4.71/6W ± 5% CF 26mm 1 R153
116-161000f26 metal film Resistor 1001/6W ± 1% MF 26mm 1 R154
R130,131,132,159,160,166,171,173,178,192,
116-161001f26 metal film Resistor 1K 1/6W ± 1% MF 26mm 12
114,115
116-161103f26 metal film Resistor 100K 1/6W ± 1% MF 26mm 1 R174
116-161502f26 metal film Resistor 15.0K 1/6W ± 1% MF 26mm 2 R162,R168
116-161504f26 metal film Resistor 1.5M 1/6W ± 1% MF 26mm 1 R142
116-161622f26 metal film Resistor 16.2K 1/6W ± 1% MF 26mm 1 R188
116-161742f26 metal film Resistor 17.4K 1/6W ± 1% MF 26mm 4 R124,R125,R127,R128
116-162001f26 metal film Resistor 2.00K 1/6W ± 1% MF 26mm 1 R202
116-162052f26 metal film Resistor 20.5K 1/6W ± 1% MF 26mm 2 R197,R198
116-162211f26 metal film Resistor 2.21K 1/6W ± 1% MF 26mm 1 R172
116-162212f26 metal film Resistor 22.1K 1/6W ± 1% MF 26mm 3 R193,R204,R206
116-162671f26 metal film Resistor 2.67K 1/6W ± 1% MF 26mm 1 R155
116-163323f26 metal film Resistor 332K 1/6W ± 1% MF 26mm 1 R195
116-163400f26 metal film Resistor 3401/6W ± 1% MF 26mm 2 R164,R169
116-163571f26 metal film Resistor 3.57K 1/6W ± 1% MF 26mm 1 R157
116-163923f26 metal film Resistor 392K 1/6W ± 1% MF 26mm 1 R201
116-164751f26 metal film Resistor 4.75K 1/6W ± 1% MF 26mm 2 R109,R110
116-164752f26 metal film Resistor 47.5K 1/6W ± 1% MF 26mm 2 R121,R122
116-164992f26 metal film Resistor 49.9K 1/6W ± 1% MF 26mm 1 R135
116-165231f26 metal film Resistor 5.23K 1/6W ± 10% MF 2 R205,R207
116-165232f26 metal film Resistor 52.3K 1/6W MF 26mm 1 R190
116-165400f26 metal film Resistor 5401/6W MF 26mm 1 R175
116-166041f26 metal film Resistor 6.04K 1/6W ± 1% MF 26mm 2 R165,R170
116-166800f26 metal film Resistor 6801/6W ± 1% MF 26mm 1 R176
116-168250f26 metal film Resistor 8251/6W ± 1% MF 26mm 2 R161,R167
116-168661f26 metal film Resistor 8.66K 1/6W ± 1% MF 26mm 1 R134
116-169311f26 metal film Resistor 9.31K 1/6W ± 1% MF 26mm 2 R189,R179
115-h103a101 variable Resistor A10K LEVEL 1 R259
variable Resistor RV16A01-20-15K-A10K-3E RABOS
115-h103a203 2 R158,R177
LEVEL, RABOS WIDTH
115-h103c201 variable Resistor RV16A01-20-15K-C10K-3E RABOS FREQ. 1 R163
14
TSS-SUB4000
Part Number Description Qty Reference Designator
INPUT/RABOS PCB
Capacitors
129-a102j633 metalized Capacitor 0.001uF 63V ± 5% MSC 1 C148
129-a103j633 metalized Capacitor 10NF 63V 1 C183
129-a104j633 metalized Capacitor 0.1U 63V ± 5% MSC 6 C116,137,138,139,143,118
129-a223j633 metalized Capacitor 0.022U 63V ± 5% MSC 1 C150
129-a224j633 metalized Capacitor 0.22uF 63V ± 5% MSC 2 C121,C122
129-a473j633 metalized Capacitor 0.047U 63V ± 5% MSC 3 C117,C119,C149
130-2b102k503 disc Capacitor 1000P 50V ± 10% 2 C181,C182
130-2b221k503 disc Capacitor 220P 50V ± 10% 3 C107,C108,C128
C112,114,124,125,130,133,135,144,145,146,
130-3f104z503 disc Capacitor 0.1U 50V +80/-20% 13
147,153,154
130-3f473m503 disc Capacitor 0.047U 50V ± 20% 1 C180
130-sl101k503 disc Capacitor 100P 50V SL ± 10% 2 C110,C120
130-s1470k503 disc Capacitor 47P 50V ± 10% 1 C127
135-3105m50 electrolytic Cap 1U 50V ± 20% 1 C126
135-3106m50 electrolytic Cap 10uF 50V ± 20% 4 C109,C111,C123,C129
135-3107m16 electrolytic Cap 100uF 16V ± 20% 5 C113,115,132,134,136
135-3107m25 electrolytic Cap 100U 25V ± 20% 1 C152
135-3226m50 electrolytic Cap 22U 50V ± 20% 1 C151
139-3227m16 low leakage electrolytic Cap 220uF 16V ± 20% 1 C131
129-a683j633 metalized Capacitor 0.068uF 63V ± 5% MSC 1 C142
Semiconductors
192-027c1815gr Transistor 2SC1815GR NPN 3 Q101,Q102,Q103
197-031n4148 diode 100mA 75V SIGNAL IN4148 ROHM 7 D105,106,108,109,110,112,113
199-15000825 zener diode 8.2V 1/2W 52mm 1 D130
190-06m4558d IC.0PA 4558D DUAL OP-AMP 2 U101,U103
190-16t1072n I.C. TL072N DUAL OP-AMP 1 U105
190-16t1074cn I.C TL074CN ST QUAD OP-AMP 3 U102,U104,U106
192-153mpf102 I.C FAIRCHILD MPF102 FET 1 Q107
Miscellaneous
180-t000ts81 TACT switch L101 T2 LO-PASS,PHASE,RABOS 3 SW102,SW103,SW104
174-0rcb202vag RCA JACK RCA-209 1 JK102
175-1c02p01 coupling 2PIN PITCH=2.5mm 2 P106,P101
CLASS D AMP PCB
Resistors
118-12061001j SMD Resistor 1.00K 1206 5% 1 R2
118-12061002j SMD Resistor 10.0K 1206 5% 6 R25,29,30,30B,7,9
118-120610r0j SMD Resistor 10.0 1206 5% 4 R20,R20B,R22,R23
118-12062002j SMD Resistor 20.0K 1206 5% 1 R26
R6,13,16,31,33,34,34,35,37,38,39,40,41,42,4
118-12062201j SMD Resistor 2.20K 1206 5% 19
3,44,45,46,32
118-12062204j SMD Resistor 2.20M 1206 5% 1 R4
118-12062701j SMD Resistor 2.70K 1206 5% 1 R10
118-12063000j SMD Resistor 300.0 1206 5% 1 R24
118-12063301j SMD Resistor 3.30K 1206 5% 5 R1,14,15,27,28
118-12063902j SMD Resistor 39.0K 1206 5% 1 R3
118-12064700j SMD Resistor 470 1206 5% 3 R8,R11,R21
118-12064701j SMD Resistor 4.70K 1206 5% 2 R5,R12
112-10180j00 fusible Resistor FMF 1W 185% 1
Capacitors
141-c0101k50 SMD Capacitor 100pF 50V 10% 1206 NP0 1 C4
141-c0220k50 SMD Capacitor 22pF 50V 10% 1206 SMT NP0 1 C5
141-c0561k50 SMD Capacitor 560pF 50V 10% 1206 NP0 1 C6
141-c5104m50 SMD Capacitor 1206 Y5V 0.1uF 50V±20% 8 C2,3,7,8,9,10,11,15
15
TSS-SUB4000
Part Number Description Qty Reference Designator
CLASS D AMP PCB
141-c7223k50 SMD Capacitor 0.022uF 50V 10% 1206 X7R 1 C13
141-d7104ka0 SMD Capacitor 0.1uF 100V 10% 1210 X7R 4 C12,C14,C18,C19
130-s1681kb03 disc Capacitor SL 680PF 200V 1
132-104kb50 mylar Capacitor 0.1U±10% 250V LS-10.mm MD 1 C20
132-105kb50 mylar Capacitor 1uF 250V ±10% 1 C40
Semiconductors
190-16t1072dts SMD I.C.TL072CDT SGS THOMSON DUAL OP-AMP 1 IC1
192-09124126qs SMD Transistor 2SC2412K-T146Q/R ROHM 2 Q1,Q4
192-09139066rs SMD Transistor 2SC3906K-T146R ROHM 2 Q2,Q8
192-091sc4672 Transistor 2SC4672(MPT3)ROHM 1 Q5B
192-09210376qs SMD Transistor 2SA1037K-T146Q/R ROHM 2 Q7,Q9
192-09215146rs SMD Transistor 2SA1514K-T146R ROHM 1 Q3
192-1582n5401 Transistor FSC 2N5401 AI-PNP 350V 500mA TO-92 1 Q6B
197-03r1s4148s SMD diode RLS4148-TE11 ROHM 8 D1,2,3,4,5,5B,6,20
199-15000563s SMD ZENER 5.6V 5% PHILIPS BZX84-C5V6 2 Z1,Z2
199-15001203s SMD ZENER 12V 5% PHILIPS BZX84-C12 4 Z3,Z4,Z5,Z6
192-232irf9640 Transistor FET IRF9640 IR P-CH TO220 2 Q10,Q10B
192-233f640n Transistor FET IRF640n INTERNATIONAL 1 Q11
Miscellaneous
122-13151k0190 CHOKE SA-500-280(PT1601B*151MAA) 1 L1
122-14300k4 Ferrite core LD1215*300KU±10% 1 L2
128-e106ma01-s non-polar ec 10uF 100V 20% 2 C16,C17
175-9f40hr2 coupling 40PIN PITCH=2.54mm HR2*40 0.2
MISCELLANEOUS
150-r1107008 power transformer TT093040561A 1 T01
152-u602015 line cord SVTFT-2 6FT 1
154-k31505t0 Fuse 3.15a 250v 30mm UL/CSA/PSE 1 F01
155-630r345b fuse holder UL/CSA 6*30mm 1 for F01
162-10100023 WIRE UL/CSA 1617#22 100mm BLK 1
162-1035d001 wire 1015#16 BRN/WHT 350mm 2PIN 1
162-1035d002 wire 1015#16 BLK/YEL/RED 350mm 6PIN 1
162-50259004 wire 250mm AWG24 1 P108
162-5035d003 wire 2468#26AWG 2PIN RED/BLK 350mm 1
163-11009 wire 100mm 4
166-5070a4fd speaker wIre 700mm #18 UL1015 #205*0.5t/#250*0.8t 1
176-wjce2 wire connector &Base CE-2 1
180-prf1003b Switch ROCK RF-1003-BB210 POWER 1
193-0s4211 INSULATOR(INSULATION SPACER)42*11 1
193-201612tr INSULATOR T0-220 16mm*12mm 1
193-201815t2 INSULATOR 2
16
TSS-SUB4000
17
TSS-SUB4000
18
TSS-SUB4000
19
TSS-SUB4000
20
TSS-SUB4000
21
TSS-SUB4000
22
TSS-SUB4000
23
TSS-SUB4000
24
TSS-SUB4000
25
TSS-SUB4000
26
TSS-SUB4000
27
TSS-SUB4000
28
TSS-SUB4000
29
TSS-SUB4000
30
TSS-SUB4000
PACKAGE
Ref # Description Part Number Qty
1 Owner's Manual 406-000-05133 1
2 Warranty Card 405-000-00328 1
3 Top/Bottom Packing 431-000-05293 2
4 Plastic Bag 1
5 RABOS Kit 335852-003 1
6 Silica Gel 3
7 Outer Carton 402-000-05237 1
8 n/a
9 15ft. RCA cable 166-015F011 1
10 TSS-SUB4000 TSS-SUB4000PLT 1
31