Text preview for : Infinity-TSSSUB800 actsub.pdf part of Infinity TSSsub800 active subwoofer
Back to : Infinity-TSSSUB800 actsub | Home
TSS-Sub800
(TSS-800 SYSTEM)
SERVICE MANUAL
Infinity Systems Incorporated
250 Crossways Park Dr.
Woodbury, New York 11797 Rev1 1/2008
TSS-Sub800
Note: The TSS-Sub800 is part of the TSS-800 system
Satellite loudspeakers:
(Charcoal) order Infinity part# TSS800CHR Sat-S-EP
(Platinum) order Infinity part# TSS800PLT Sat-S-EP
Center channel:
(Charcoal) order Infinity part# TSS-800CHR CEN-E
(Platinum) order Infinity part# TSS-800PLT CEN-E
CONTENTS
BASIC SPECIFICATIONS . . . . . . . . . ...................................... .. . . . . . 1
PACKAGING/ACCESSORIES. . . . . . . . . . . . . . . . . ........... . .. .. ... . . . . . 2
DETAILED SPECIFICATIONS . . . . . . . . . . . . . . . . . ........... . .. .. .. . . . . . 3
CONTROLS. ....................... .. . ..................................................... 5
CONNECTIONS . . . . . . . . . . . .................................................... . . . 6
OPERATION....... . . . . .. . . . . . . . .. .. . . . .. .. . . . . ............. . . ... . . . . . . .7
EXPLODED VIEW-MECHANICAL PARTS LIST....... . .............................8
TEST SET-UP/PROCEDURE. . . . . . . . . . . . . . . . . ........... . .. .. ..... . . . . . 9
BLOCK DIAGRAM. . . . ..................... .................................. . . .. . ... . 10
TROUBLESHOOTING FLOW CHART....... . ........................................12
PCB DRAWINGS. .. . . . . . . . . . . . . . .. . . . . ...................................... ...13
ELECTRICAL PARTS LIST ............. .................................................19
IC TRANSISTOR PINOUTS . ... . . .. . . . . . .................................. . . . 23
SCHEMATIC DIAGRAMS . . ........................................................... . .24
TSS-Sub800 Specifications
Frequency Range: 34Hz 150Hz (±3dB)
Amplifier Output: 150 watts RMS, 300 watts Peak
Low-Frequency Driver: 10" (254mm)
Crossover Frequency: 50Hz 150Hz, 24dB/Octave, continuously variable
Dimensions (H x W x D): 15-3/4" x 14" x 15" (400mm x 356mm x 381mm)
Weight: 34.6 lb (15.7kg)
Infinity continually strives to update and improve existing products, as well as create new ones. The specifications
and construction details in this and related Infinity publications are therefore subject to change without notice.
1
TSS-Sub800
PACKAGING
2
TSS-Sub800
TSS-Sub800 100W Powered Sub/ Plate Amp
LINE VOLTAGE Yes/No Hi/Lo Line Unit Notes
US 120VAC/60Hz Yes 108-132 Vrms Normal Operation
Europe 220-240VAC, 50-60Hz Yes 220-230 Vrms Normal Operation
Parameter Specification Unit QA Test Limits Conditions Notes
Amp Section
Type (Class AB, D, other) AB AB n/a 120V Model External heatsink required
Type (Class AB, D, other) G G n/a 230V Model External heatsink required
Load Impedance (speaker) 4 Ohms n/a Nominal
Rated Output Power 100 Watts 95 Single input driven
THD@ Rated Power 0.5 % 1 22K filter
THD @ 1 Watt 0.1 % 0.3 22K filter
DC Offset 10 mV-DC 50 @ Speaker Output
Measured at amplifier board speaker output
Damping factor >100 DF 100 50Hz-4 Ohms load terminals, Output power 90 Watts.
Input Sensitivity
Input Frequency 50 Hz 50 Nominal Freq.
Line Input (L&R) 15.62 mVrms ±2dB To 1 Watt Single input driven, AP Zo=600 Ohms
LFE Input 10.36 mVrms ±2dB To 1 Watt LFE input driven only, AP Zo=600 Ohms
Signal to Noise
SNR-A-Weighted 100 dBA 85 rel. to rated power A-Weighting filter
SNR-unweighted 80 dBr 80 rel. to rated power 22K filter
SNR @ 1W-unweighted 60 dBr 60 rel. to 1W Output 22K filter
Volume @max, using RMS reading
Residual Noise Floor 1.5 mVrms 2.5 DMM/VOM (or A/P)
Volume @max, w/ A/P Swept Bandpass
Residual Noise Floor 1 mVrms(max) 2 Measurement (Line freq.+ harmonics)
Input Impedance
Line input L&R , LFE >10 K ohms n/a Nominal
Filters
2nd order variable 50-150Hz + 2nd order
Low Pass (fixed or variable) 4th order -- ±2dB fix
Slope & Q dB/Octave n/a
Subsonic filter (HPF) 2nd order fix Hz ±2dB
Slope & Q dB/Octave n/a
Limiter (yes/no) YES -- Functional
THD at Max. Output Power 1 % Functional
Features
LFE Input YES Functional
Phase Switch (yes/no) YES -- Functional
Volume pot Taper (lin/log) LOG -- Functional
ATO YES Functional
Input Configuration
Line In (L,R) L ,R -- Functional RCA inputs (L&R)
Line level in LFE LFE Functional RCA single input
Signal Sensing (ATO)
Auto-Turn-On (yes/no) YES -- Functional
ATO Input Frequency 50 Hz Functional @ p
ATO Level 2 mV Functional driven
Amp connected and AC on, then input
ATO Turn-on time 5 ms Functional signal applied
Auto Mute/ Turn-OFF Time 10 minutes Functional T before muting, after signal is removed Auto turn of time (T) must be 5 > T <15
Power on Delay time 3 sec. Functional AC Power Applied
Transients/Pops
ATO Transient 5 mV-peak 10 @ Speaker Outputs
Turn-on Transient 50 mV-peak 100 @ Speaker Outputs AC Line cycled from OFF to ON
Turn-off Transient 50 mV-peak 100 @ Speaker Outputs AC Line cycled from ON to OFF
Efficiency
Maximum allowable input power under
nominal Input voltage and frequency, HOT
Stand-by Input Power 14 Watts 18 @ nom. line voltage or COLD operation.
Power Cons.@rated power 195 Watts 210 @ nom. line voltage 100 Watts @ 4 Ohms
3
TSS-Sub800
Parameter Specification Unit QA Test Limits Conditions Notes
Protection
Short Circuit Protection YES -- Functional Direct short at output
Temperature rise should not exceed 35K
Thermal Protection 65 deg. C -- Functional @1/8 max unclipped Power rise
DC Offset Protection YES -- Functional DC present at Speaker Out leads Relay or crowbar (for driver/fire protection)
Line Fuse Rating External fuse with UL/SEMKO rated holder
Type-T or Slo Blo, Fuse markings T2.5A,
120 VAC 2.5 Amps 250V
Type-T, Low breaking capacity, Fuse
230 VAC 1.25 Amps markings T1.25AL, 250V
4
TSS-Sub800
SUBWOOFER CONTROLS
Rear Panel Subwoofer-Level Control
Crossover-Frequency Adjustment
Phase Switch
ˇ LFE Input
Line-Level Inputs
TM
Power Indicator LED
Ł Power Switch
˘
A Few Suggestions
§ We recommend that you do not operate your speakers or
subwoofer with the bass, treble and loudness controls set to
full boost.This will place undue strain on your electronics and
speakers and could damage them.
TSS-Sub800 ¶
NRTU/C
CSA22-2 NO.1
UL 1492
The volume control setting on your processor/preamp or receiver
is not a specific indication of the overall loudness level of the
speakers.The only important consideration is the loudness level at
which the system can be played, regardless of where the volume
control is set.
Always turn down the volume control setting on your processor/
preamp or receiver when changing sources, or switching inputs to
AM or FM operation. Excessively loud transients (clicks or popping
sounds) can damage the satellite speakers and possibly the
subwoofer.
Important!
Whenever changing cables, pulling plugs, etc., ALWAYS TURN OFF
ALL EQUIPMENT, including the subwoofer.
5
TSS-Sub800
SUBWOOFER CONNECTIONS
If you have a Dolby® Digital or DTS® receiver/ If your receiver/processor does not contain
processor with a low-frequency-effects (LFE) a Dolby Digital or DTS processor but has a
or subwoofer output: subwoofer output:
RECEIVER/PROCESSOR
SUBWOOFER OR
LFE OUTPUT
15' (4.5m)
subwoofer
cable
included 15' (4.5m)
subwoofer cable
included
NOTE: If your receiver/processor has only one sub out,
you may use either the L or R input.
TSS-Sub800/230 TSS-Sub800/230
6
TSS-Sub800
OPERATION
Surround Modes Crossover Adjustment
When using the TSS-800 in a Dolby Digital or DTS home theater The Crossover Frequency Control determines the highest
system, make sure all speakers are set to "Small" In a Dolby
. frequency at which the subwoofer reproduces sounds. For the
Pro Logic® home theater system, make sure the receiver's TSS-800, it is recommended that this control be set at 120Hz
center channel mode is set to "Normal." (approximately the 3 o'clock position).
Some Dolby Digital-equipped receivers/processors offer different NOTE: This control will have no effect if the LFE Input is
setup options for each source or surround mode (e.g., CD-stereo, used. If you have a Dolby Digital or DTS receiver/processor,
videotape, Dolby, Pro Logic). In each case, follow your equipment's the low-pass frequency is set by the receiver/processor. Consult
instructions to ensure that the subwoofer output is turned on and your owner's manual to learn how to view or change this setting.
that the speakers are set to "Small" in each mode. A setting of 120Hz 150Hz is recommended.
Power On Phase Control
Plug your subwoofer's AC cord into a wall outlet. Do not use the The Phase Switch determines whether the subwoofer
outlets on the back of the receiver. speaker's pistonlike action moves in and out with the main
Initially set the Subwoofer Level Control to the"MIN" position. speakers (0°) or opposite the main speakers (180°). Proper
phase adjustment depends on several variables such as room
Turn on the subwoofer by pressing the Power Switch on the size, subwoofer placement and listener position. Adjust the phase
rear panel. switch to maximize bass output at the listening position.
Turn on your entire audio system and start a CD or movie sound-
track at a moderate level. Final Positioning
After correctly connecting the TSS-800 system and verifying that
Auto On/Standby both the subwoofer and all satellite speakers are playing, it is
With the Power Switch in the ON position, the LED on the rear time to optimize the system for your particular listening room.
panel will remain lit in green or red to indicate the ON or Earlier, you placed the subwoofer in its general location. Finding
STANDBY mode of the subwoofer. the exact location for optimum performance sometimes only
RED = STANDBY (No signal detected, Amp Off) involves moving the speakers up to a few inches in any
direction. We urge you, therefore, to experiment with placement,
GREEN = ON (Signal detected, Amp On)
if possible, until your speakers deliver their full potential.
The subwoofer will automatically enter the Standby mode after
approximately 10 minutes when no signal is detected from your
system.The subwoofer will then power on instantly when a signal
is detected. During periods of normal use, the Power Switch
MAINTENANCE AND SERVICE
can be left on.You may turn off the Power Switch for extended The satellite and subwoofer enclosures may be cleaned using a
periods of nonoperation, e.g., when you are away on vacation. soft cloth to remove fingerprints or to wipe off dust.
Adjust Level All wiring connections should be inspected and cleaned or
Turn the Subwoofer Level Control up about halfway. If no remade periodically.The frequency of maintenance depends on
sound emanates from the subwoofer, check the AC-line cord and the metals involved in the connections, atmospheric conditions
input cables.Are the connectors on the cables making proper and other factors, but once per year is the minimum.
contact? Is the AC plug connected to a "live" receptacle? Has the
Power Switch been pressed to the ON position? Once you have In the event that your TSS-800 ever needs service, contact your
confirmed that the subwoofer is active, proceed by playing a CD local Infinity dealer or distributor, or visit www.infinitysystems.com
or DVD. Use a selection that has ample bass information. for a service center near you.
Set the overall volume control of the receiver/processor to a
comfortable level. Adjust the Subwoofer Level Control until
you obtain a pleasing blend of bass. Bass response should
not overpower the room but rather be adjusted so there is
a harmonious blend across the entire musical range. Many
users have a tendency to set the subwoofer volume too loud,
adhering to the belief that a subwoofer is there to produce lots of
bass.This is not entirely true. A subwoofer is there to enhance
bass, extending the response of the entire system so the bass
can be felt as well as heard. However, overall balance must
be maintained or the music will not sound natural. An experienced
listener will set the volume of the subwoofer so its impact on
bass response is always there but never obtrusive.
7
TSS-Sub800
8
TSS-Sub800
Test Set Up and Procedure
Equipment needed:
· Function/signal generator/sweep generator
· Integrated Amplifier
· Multimeter
· Speaker cables
General Unit Function (UUT = Unit Under Test)
1) From the signal generator, connect one line level (RCA) cable to the Subwoofer Line Level Input jacks L/R
on the UUT. Use a Y-cable from a mono source if necessary to connect to both inputs. Do not connect to
the single LFE input.
2) On the amplifier, turn the LEVEL control full counterclockwise (MIN)
3) Turn the Crossover Frequency Adjustment full CW (150Hz)
4) Turn on generator, adjust to 100mV, 50 Hz.
5) Plug in UUT; turn the power switch ON. LED should be Red. Turn LEVEL control full clockwise (MAX)
6) LED should now be Green; immediate bass response should be heard and felt from bottom port tube
opening.
7) Turn off generator, turn LEVEL control fully counterclockwise, disconnect RCA cable.
Sweep Function
1) Follow steps 3-6 above, using a sweep generator as a signal source.
2) Sweep generator from 20Hz to 300Hz. Listen to the cabinet and drivers for any rattles, clicks, buzzes or
any other noises. If any unusual noises are heard, remove woofers and test.
Driver Function
1) Remove woofer from cabinet; detach + and - wire clips.
2) Check DC resistance of woofer; it should be 4.8 ohms ±10%
3) Connect a pair of speaker cables to driver terminals. Cables should be connected to an integrated amplifier
fed by a signal generator. Turn on generator and adjust so that speaker level output is 5.0V.
4) Sweep generator from 20Hz to 1kHz. Listen to driver for any rubbing, buzzing, or other unusual noises.
9
TSS-Sub800
10
TSS-Sub800
11
TSS-Sub800
TSS-Sub800 AMP
Troubleshooting Flow Chart
AMP no signal out
no
yes Check Fuse,Transformer,
D110, etc
Dc voltage check ±Vcc
yes
yes no
Check Q117,118,119,D109 etc
Check+/-15VDC
yes
yes
Led light green or red led red Check,Q206,Q207,U203 etc
led light green yes yes
Check U201 CheckU201,U202,VR201
no VR202. etc
Check U202 pin14 signal pin14 signal
yes yes no
no
Check limiter board C304 Check U301,R343,R344 ,
C340,Q301,Q302, etc
yes
yes yes Check ,+VCC& -VCC
Test R121,R122 signal no DC voltage Check J123,J124 etc
no
yes yes
Check Q107,Q108,Q105,
Check RY101,D102,Q113,Q114 etc
Q106,Q103,Q104,U101,etc
yes
no
Check U101,Q115,Q116,R138 etc Set R138 to R140'S
yes Voltage is 0.51VDC
yes
Check P102 signal The Amp ass'Y OK, END
12
TSS-Sub800
13
TSS-Sub800
14
TSS-Sub800
15
TSS-Sub800
16
TSS-Sub800
17
TSS-Sub800
18
TSS-Sub800
TSS-Sub800 (120v) Electrical Parts List
Part Number Description Qty Reference Designator
PREAMP PCB
Resistors
110-16102j26-e Resistor 1k 1/6W ±5% CF 26mm (RoHS) 4 R213,R214,R215,R254
R212.R216.R217.R220.R221.R222.R225.R228.R232.
110-16103j26-e Resistor 10k 1/6W ±5% CF 26mm (RoHS) 12
R235.R240.R248
110-16104j26-e Resistor 100k 1/6W ±5% CF 26mm (RoHS) 2 R231.R266
110-16105j26-e Resistor 1M 1/6W ±5% CF 26mm (RoHS) 1 R259
110-16122j26-e Resistor 1.2K 1/6W ±5% CF 26mm (RoHS) 1 R264
110-16151j26-e Resistor 150OHM 1/6W ±5% CF 26mm (RoHS) 1 R253
110-16154j26-e Resistor 150k 1/6W ±5% CF 26mm (RoHS) 1 R252
110-16183j26-e Resistor 18k 1/6W ±5% CF 26mm (RoHS) 1 R262
110-16205j26-e Resistor 2M 1/6W ±5% CF 26mm (RoHS) 1 R257
110-16223j26-e Resistor 22K 1/6W ±5% CF 26mm (RoHS) 3 R247.R250.R255
110-16333j26-e Resistor 33K 1/6W ±5% CF 26mm (RoHS) 1 R249
110-16472j26-e Resistor 4.7K 1/6W ±5% CF 26mm (RoHS) 2 R258.R260
110-16473j26-e Resistor 47K 1/6W ±5% CF 26mm (RoHS) 2 R219.R251
110-16512j26-e Resistor 5.1K 1/6W ±5% CF 26mm (RoHS) 3 R211.R229.R230
116-161002f26-e Resistor 10K 1/6W ±1% MF 26mm (RoHS) 1 R7
116-161471f26-e Resistor 1.47K 1/6W ±1% MF 26mm (RoHS) 1 R4
116-161503f26-e Resistor 150.0K 1/6W ±1% MF 26mm (RoHS) 1 R1
116-161542f26-e Resistor 15.4K 1/6W ±1% MF 26mm (RoHS) 2 R237.R238
116-162400f26-e Resistor 240OHM 1/6W ±1% MF 26mm (RoHS) 1 R2
116-162871f26-e Resistor 2.87K 1/6W ±1% MF 26mm (RoHS) 1 R234
116-163602f26-e Resistor 36K 1/6W ±1% MF 26mm (RoHS) 1 R233
116-165361f26-e Resistor 5.36K 1/6W ±1% MF 26mm (RoHS) 1 R6
116-1664r9f26-e Resistor 64.9OHM 1/6W ±1% MF 26mm (RoHS) 1 R5
116-166801f26-e Resistor 6.8K 1/6W ±1% MF 26mm (RoHS) 4 R224.R223.R226.R227
116-168251f26-e Resistor 8.25K 1/6W ±1% MF 26mm (RoHS) 2 R3
115-h203b208-e VR 20KB*2 (RoHS) CROSSOVER 1 VR202
115-h503a104-e VR 50KA*1 (RoHS) LEVEL 1 VR201
Capacitors
129-a104j633-e metallize Capacitor 0.1uF 63V ± 5% MSC (RoHS) 2 C5.C215
129-a153j633-e metallize Capacitor 0.015uF 63V ± 5% MSC (RoHS) 1 C224
129-a224j633-e metallize Capacitor 0.22uF 63V ± 5% MSC (RoHS) 1 C216
129-a274j633-e metallize Capacitor 0.27uF 63V ± 5% MSC (RoHS) 1 C218
129-a473j633-e metallize Capacitor 0.047uF 63V ± 5% MSC (RoHS) 1 C4
129-a474j633-e metallize Capacitor 0.47uF 63V ± 5% MSC (RoHS) 2 C221.C222
129-a823j633-e metallize Capacitor 0.082uF 63V ± 5% MSC (RoHS) 1 C217
130-2b221k503-e disc Capacitor 220pF 50V +/-10% Y5P (RoHS) 9 C207.C208.C210.C211.C212.C214.C220.C230.C249
130-3f104z503-e disc Capacitor 0.1uF 50V +80/-20% Y5V (RoHS) 7 C232.C242.C244.C245.C246.C252.C254
130-sl470k503-e disc Capacitor 47pF 50V +80/-20% SL (RoHS) 1 C229
132-103j503-e mylar Capacitor 0.01UF 50V ± 5% (RoHS) 1 C223
135-3105m50-e electrolytic 1uF 50V ±20% 85 (RoHS)
1 C228
135-3106m50-e electrolytic 10uF 50V ±20% 85 (RoHS)
8 C206.C213.C219.C231.C241.C243.C251.C253
135-3107m16-e electrolytic 100uF 16V ±20% 85 (RoHS)
2 C233.C234
135-3226m50-e electrolytic 22uF 50V ±20% 85 (RoHS)
1 C225
Semiconductors
192-027c1815gr-e transistor 2SC1815GR TOSHIBA (RoHS) NPN 1 Q201.Q206.Q207
197-031n4148-e diode 100mA 75V SIGNAL IN4148 ROHM (RoHS) 9 D201.D202.D118.D117.D207.D206.D211.D212.D214
199-15000335-e zener diode 3.3V 1/2W 52mm RoHS 1 D213
190-06m4558d-e IC OPA 4558 DUAL OP-AMP 1 U203
190-16ti074cn-e I .C TL074cm st QUAD OP-AMP 2 U201.U202
195-10204hgw-e LED Red-Green 204HGW 3(RoHS) 1 D209
19
TSS-Sub800
Part Number Description Qty Reference Designator
PREAMP PCB
Miscellaneous
162-50159201-e WIRE 2PIN White-Red 150mm 1 TO LIMIT BOARD
174-0rca326p-e RCA JACK RCA-326 3PIN(RoHS) 1 JK202
180-tms7210v-e SWITCH SLIDE 6PIN MS-7210(RoHS) PHASE 1 SW301
362-FE-00041-0LAE PCB support 11.75*8.5*12.5H(RoHS) 1
LIMITER PCB
Resistors
110-16103j26-e Resistor 10K 1/6W ±5% CF 26mm (RoHS) 2 R109,R162
110-16102j26-e Resistor 1K 1/6W ±5% CF 26mm (RoHS) 8 R301.R303.R304.R308.R309.R314.R340.R344
110-16183j26-e Resistor 18K 1/6W ±5% CF 26mm (RoHS) 1 R302
110-16223j26-e Resistor 22K 1/6W ±5% CF 26mm (RoHS) 2 R310.R312
110-16273j26-e Resistor 27K 1/6W ±5% CF 26mm (RoHS) 1 R341
110-16333j26-e Resistor 33K 1/6W ±5% CF 26mm (RoHS) 1 R305
110-16472j26-e Resistor 4.7K 1/6W ±5% CF 26mm (RoHS) 2 R342.R343
110-16474j26-e Resistor 470K 1/6W ±5% CF 26mm (RoHS) 1 R307
110-16751j26-e Resistor 750 1/6W ±5% CF 26mm (RoHS) 2 R311.R313
110-16755j26-e Resistor 7.5M 1/6W ±5% CF 26mm (RoHS) 1 R306
Capacitors
130-3f104z503-e disc Capacitor 2700pF 100V +80%/-20%(RoHS) 2 C305.C306
132-103j503-e mylar Capacitor 0.01UF 50V ± 5% (RoHS) 2 C302.C303
135-3226m50-e electrolytic 22uF 50V ±20% 85(RoHS) 2 C301.C340
135-3476m25-e electrolytic 47uF 25V ±20% 85(RoHS) 1 C304
Semiconductors
192-027c1815gr-e transistor 2SC1815GR TOSHIBA (RoHS) NPN 2 Q301.Q302
197-031n4148-e diode 100mA 75V SIGNAL IN4148 ROHM (RoHS) 2 D301.D302
190-16tl074cn-e I .C TL074cm st QUAD OP-AMP 1 U301
Miscellaneous
162-50289001-e WIRE 7PIN 280mm UL2468 AWG26(RoHS) 1
162-80098201-e WIRE 2PIN 90mm GRAY AWG26(RoHS) 1
175-9f40hr2-e Connecter 40PIN PITCH2.54mm,HR2*40(RoHS) 1
POWER/MAIN PCB
Resistors
110-10821jk2-e Resistor 820 1W ±5% 10mm (RoHS) 1 R132,
110-122r2j15-e Resistor 2.2 1/2W ±5% 15mm (RoHS) 1 R127,
110-20331jk2-e Resistor 330 2W ±5% 5mm(RoHS) 2 R146,R149,
113-50r10j10-e cement Resistor 0.1 5W ±5% (RoHS) 2 R121,R122,
114-03302m0-e semi-fixed Resistor 3K 0.3W ±20% (RoHS) 1 R138,
110-14472j26-e Resistor 4.7K 1/4W ±5% CF 26mm (RoHS) 2 R147,R150,
110-14681j26-e Resistor 680 1/4W ±5% CF 26mm (RoHS) 2 R148,R151,
110-16101j26-e Resistor 100 1/6W ±5% CF 26mm (RoHS) 1 R120,
110-16102j26-e Resistor 1K 1/6W ±5% CF 26mm (RoHS) 1 R124,
110-16103j26-e Resistor 10K 1/6W ±5% CF 26mm (RoHS) 1 R134,
110-16105j26-e Resistor 1M 1/6W ±5% CF 26mm (RoHS) 1 R143,
110-16123j26-e Resistor 12K 1/6W ±5% CF 26mm (RoHS) 2 R135,R139,
110-16152j26-e Resistor 1.5K 1/6W ±5% CF 26mm (RoHS) 2 R141,R142,
110-16153j26-e Resistor 15K 1/6W ±5% CF 26mm (RoHS) 4 R118,R145,R152,R154,
110-16154j26-e Resistor 150K 1/6W ±5% CF 26mm (RoHS) 1 R131,
110-16181j26-e Resistor 180 1/6W ±5% CF 26mm (RoHS) 2 R111,R114,
110-16182j26-e Resistor 1.8K 1/6W ±5% CF 26mm (RoHS) 1 R153,
20
TSS-Sub800
Part Number Description Qty Reference Designator
POWER/MAIN PCB
110-16223j26-e Resistor 22K 1/6W ±5% CF 26mm (RoHS) 3 R128,R129,R133,
110-16332j26-e Resistor 3.3K 1/6W ±5% CF 26mm (RoHS) 3 R106,R107,R144,
110-16392j26-e Resistor 3.9K 1/6W ±5% CF 26mm (RoHS) 2 R105,R108,
110-16393j26-e Resistor 39K 1/6W ±5% CF 26mm (RoHS) 1 R126,
110-16470j26-e Resistor 47 1/6W ±5% CF 26mm (RoHS) 4 R112,R113,R115,R116,
110-16471j26-e Resistor 470 1/6W ±5% CF 26mm (RoHS) 1 R140,
110-16472j26-e Resistor 4.7K 1/6W ±5% CF 26mm (RoHS) 3 R110,R125,R130,
110-16473j26-e Resistor 47K 1/6W ±5% CF 26mm (RoHS) 1 R101,
110-16560j26-e Resistor 56 1/6W ±5% CF 26mm (RoHS) 1 R117,
110-16563j26-e Resistor 56K 1/6W ±5% CF 26mm (RoHS) 1 R104,
110-16682j26-e Resistor 6.8K 1/6W ±5% CF 26mm (RoHS) 1 R109,
Capacitors
132-223ja03-e mylar Capacitor 0.022uF 100V ±5% (RoHS) 2 C123,C127,
135-3107m16-e electrolytic cap. 100uF 16V ±20% (RoHS) 1 C110,
135-4688m50-e electrolytic cap. 6800U/50V ±20% D25X45mm (RoHS) 2 C121,C122,
130-2b102k503-e disc Capacitor 1000P 50V ±10% (RoHS) 1 C116,
130-3f104z503-e disc Capacitor 0.1U 50V +80/-20% (RoHS) 4 C108,C113,C115,C119,
130-3f473m503-e disc Capacitor 0.047U 50V ±20% (RoHS) 1 C106,
132-104j503-e mylar Capacitor 0.1U 50V ±5% (RoHS) 1 C107,
132-223ja03-e mylar Capacitor 0.022uF 100V ±5% (RoHS) 4 C124,C125,C126,C128,
135-3105m50-e electrolytic cap. 1U 50V ±20% (RoHS) 2 C105,C112,
135-3107m16-e electrolytic cap. 100uF 16V ±20% (RoHS) 3 C109,C117,C120,
135-3226m50-e electrolytic cap. 22U 50V ±20% (RoHS) 2 C114,C118,
135-3227m10-e electrolytic cap. 220U 10V ±20% (RoHS) 2 C129,C130,
135-3227m16-e electrolytic cap. 220U 16V ±20% (RoHS) 1 C111,
135-3476m25-e electrolytic cap. 47U 25V ±20% (RoHS) 1 C103,
130-sl101k503-e disc Capacitor 100P 50V SL ±10% (RoHS) 2 C139,C140,
Semiconductors
190-06m4558d-e IC OPA 4558 DUAL OP-AMP 1 U101,
192-021tip35c-e transistor TIP35C (RoHS) NPN 1 Q107,
192-022tip36c-e transistor TIP36C (RoHS) PNP 1 Q108,
192-027c1815gr-e transistor 2SC1815GR TOSHIBA(RoHS) NPN 2 Q101,Q115,
192-201d882y-e transistor KSD882Y (RoHS) PNP 1 Q117,
192-202b772y-e transistor KSB772Y (RoHS) PNP 1 Q119,
192-991d669a-e transistor HI-SINCERITY HSD669A (RoHS) NPN 1 Q106,
192-992b649t-e transistor HSB649T (RoHS) PNP 1 Q105,
197-00kbl405-e diode 4A 500V KBL405 (RoHS) BRIDGE 2 D110,
197-101n4002-e diode 1N4002TB (RoHS) 2 D104,
192-027c1815gr-e transistor 2SC1815GR TOSHIBA(RoHS) NPN 5 Q102,Q111,Q112,Q113, Q118,
192-028a1015gr-e transistor 2SA1015GR TOSHIBA(RoHS) PNP 2 Q114,Q116,
192-1572n5551-e transistor FSC 2N5551 (RoHS) NPN 2 Q103,Q109,
192-1582n5401-e transistor FSC 2N5401 AI-PNP 350V 500mA TO-92 (RoHS) 2 Q104,Q110,
197-031n4148-e diode 100mA 75V SIGNAL 1N4148 ROHM (RoHS) 4 D101,D103,D105,D108,
199-15000335-e zener diode 3.3V 1/2W 52mm (RoHS) 1 D102,
199-15000625-e zener diode HZ6C2 RENESAS (RoHS) 2 D106,D107,
199-15001605-e zener diode HZ16-2 RENESAS (RoHS) 1 D109,
Miscellaneous
171-udhss124d-e Relay 5A 24V UDH-SS124D (RoHS) 1 RY101,
175-1c07v01-e wire connector & base 7PIN PITCH=2.5mm (RoHS) 1 P101,
175-1d02v01-e wire connector and base 2PIN PITCH=3.96mm(RoHS) 1 P102,
175-1d03v01-e wire connector and base 3 PIN PITCH=3.96mm (RoHS) 1 P103,
193-3m2520-e insulator TO-3P 25x20mm (RoHS) 2 for Q107,Q108,
323-AL-00020-0LAE HEAT SINK 65*32*31 1
351-AM03014A094-E M3*14 machine screw (RoHS) 1
352-AM03008D040-E 3*8 ping screw (RoHS) 4
21
TSS-Sub800
Part Number Description Qty Reference Designator
POWER/MAIN PCB
361-FE-00051-0LAE transistor's holder 14.2*8.0*5.2 t=1.6mm (RoHS) 1
361-NYL-00054-0LAE transistor's insulated pad (SW06002) (RoHS) 2
MISCELLANEOUS/MECHANICAL
150-e8604107-e power transformer EI-86 60Hz 120VTT0869906580 1
152-u602015-e power supply cord SVT FT-2 6FT (RoHS) 1
154-u25006t0-e fuse 2.5A 250V 20mm (RoHS) 1
155-520020-e fuse holder R3-11 (RoHS) 1
162-10082007-e WIRE RED 18AWG 80mm 8mm#1015 (RoHS) 1
176-wjce1-e wire connector pin CE-1 (RoHS) 1
180-prf1003s-e power switch ROCKER RF-1003-BB2-OHA (RoHS) 1
350-EM04012D024- 4*12 wood screw (RoHS) 4
351-HM04016A218-E M4*16 machine screw (RoHS) 4
351-AM03008A079-E M3*8 machine screw (RoHS) 7
352-AM03010D065-E 3*10 ping screw (RoHS) 1
352-AM03008D040-E 3*8 ping screw (RoHS) 8
354-GM04002-E M4 nut adding pad (RoHS) 4
362-FE-00013-0LAE PCB support L TYPE t=1.6mm 89*9*1.6T (RoHS) 2
311-ABS-00028-0BAE knob CROSSOVER,LEVEL 46077-W P.V.C. (RoHS) 2
335-NYL-00002-0BAE power wire clip 4K-4 NO-BB(RoHS) 2
333-EVA-00783-0BAE EVA W 198*12*2.0T 2
333-EVA-00807-0BAE EVA L 274*12*2.0T (RoHS) 2
333-EVA-00826-0BAE EVA W 198*12*1.0T (RoHS) 2
333-EVA-00835-0BAE EVA L 274*12*1.0T (RoHS) 2
320-RUB-00033-0BAE rubber foot pad 25*21*4t (RoHS) 4
123-14j70d-e Ferrite Core U-16.3*8.2*13 (J70)+CASE (RoHS) 1
337-CU-00101-0LAE copper foil 65L*50W (RoHS) 1
323-AL-00106-0BBE HEAT SINK 117.5*71.5*25 (RoHS) 1
302-AL-00406-0BAE aluminium faceplate 300*200*2.5T black(RoHS) 1
306-ABS-00177-0BAE Plastic rear housing 198*298*102mm (RoHS) 1
162-50652003-e WIRE 650mm RED=205# 0.5T BLK=110# 0.5T (RoHS) 1
130-3f472md00-e disc Capacitor 4700P 400V ± 20% (RoHS) 1 C001 on Power Switch
22
TSS-Sub800
23
TSS-Sub800
1 2 3 4 5 6
FM phase sw
P1 1 4
2 5 C252 C251 C244 C243 C246 +15V
1 0.1uF/C 10uF 0.1uF/C 10uF 0.1uF/C
3 6
2
4
4
8
D SW301A SW301B +15v D
FM phase sw C218 U201D
U201C 0.27uF/MSC TL074 U203
C208 U201A 13
C216 TL074 4558 -15v
220P 3 TL074 9 14 U201 U202
2
5
0.22uF/MSC R226 R227 -15V
4
1 8 3 1 6 4 12 TL074 TL074
11
11
C206
JK202A R213 R216 2 1 2 R224 10
6.8K VR202A 6.8K VR202B C217
2 10K R212 6.8K B20K B20K R228
1K 10uF R211 5.1K 0.082uF/MSC
G2 C211 10k R223 C215 R225 10K C254 C253 C242 C241 C245
220P 6.8K
1 0.1uF/MSC 10K 0.1uF/C 10uF 0.1uF/C 10uF 0.1uF/C
2
1
D201 D202 C207 220P
1 R214 2 R217 4148 4148
1
2
1K 10K
C210 -15V +15v
220P
1
R4
3
C5 R1 R5 1.47K
1 2
1
A50K 0.1uF/MSC 150K 64.9 C224
R229 VR201 U202D
U202C 0.015uF/MSC TL074 C225
13
2
5.1k R231 100K R234 C4 TL074
U202B R3 8.25K 9 14
C219 2.87K 6 TL074 8 R238 12
C220 C1 C2
2
220P C3
2 C221 C222 7 0.047uF/MSC 10 22uF
C R237 22K C
1 5 R2 240 15.4K R240
10uF 3 JUP JUP JUP Q201
2
U202A .47uF/MSC .47uF/MSC OPT 10K
1
R230 R7 R6
TL074 3
1
5.1K R232 R233 R235 10K 5.36K C223
R220 10k 36K 10K 0.01uF/MSC
10k 2 R247 R248
1
OPT OPT
2
+15V
C213
10uF R257
Q207
2
C231 D213 2M R260
R253 C1815
1 2 4.7K
3 M201
150 3.3V SGO
10uF 7
PTC
1
C230 220P D216 6
U203B +15V