Text preview for : Jbl-ES150P actsub.pdf part of JBL ES150P active subwoofer
Back to : Jbl-ES150P actsub.pdf | Home
ES Series
Powered Subwoofer
ES150P
Service Manual
JBL Consumer Products 250 Crossways Park Dr. Woodbury, New York 11797 Released 2008 Discontinued XXXX Rev0 3/2008
ES150P
- CONTENTS BASIC SPECIFICATIONS ......................................1 DETAILED SPECIFICATIONS ................................2 PACKING.............................................................4 CONTROLS/CONNECTIONS..................................5 OPERATION ........................................................7 EXPLODED VIEW/PARTS LIST...............................8 TEST SET-UP AND PROCEDURE...........................9 AMPLIFIER BLOCK DIAGRAM...............................10 DETAILED TROUBLESHOOTING.................... ......12 P.C.B. DRAWINGS...............................................13 ELECTRICAL PARTS LIST ...................................18 IC/TRANSISTOR PINOUTS.....................................23 SCHEMATICS....................................................24
ES150P SPECIFICATIONS
Amplifier Power (RMS): Peak Dynamic Power *: Driver: Inputs: Low-Pass Frequency: 300 Watts 500 Watts 10" (254mm) PolyPlasTM Line Level (switchable to LFE) Variable from 50Hz to 150Hz (24dB/octave, continuously variable) Frequency Response: Dimensions (H x W x D): Weight: 27Hz Low-pass crossover setting 18" x 13-1/4" x 15-1/4" (457mm x 337mm x 387mm) 39 lb/17.7kg
JBL continually strives to update and improve existing products, as well as create new ones. The specifications and details in this and related JBL publications are therefore subject to change without notice.
* The Peak Dynamic Power is measured by recording the highest center-to-peak voltage measured across the output of a resistive load equal to minimum impedance of the transducer, using a 50Hz sine wave burst, 3 cycles on, 17 cycles off.
1
ES150P
JBL ES150P 225W Powered Sub Amp
LINE VOLTAGE US 120vac/60Hz EU 230vac/50-60Hz Yes/No Yes Yes Hi/Lo Line 108-132 207-253 Nom. 120 230 QA Test Limits n/a n/a Unit Vrms Vrms Notes Normal Operation Normal operation, MOMS required
Parameter Amp Section Type (Class AB, D, other) Min. Load Impedance (speaker) AVG System impedance Rated Output Power
Specification D 4 5.18 225
Unit n/a Ohms Ohms Watts
Conditions
Notes
Nominal AP Computed based on system Reference impedance curve 210
Over the BW of 20 to 500Hz Average RMS power, 3/20 Cycles 50 Hz, Driven 6dB above its input sensitivity , average of the first 4 consecutive peaks
AVG RMS Dynamic Power THD @ Rated Power THD @ 1 Watt DC Offset Damping factor Input Sensitivity Input Frequency L or R Inputs LFE mode using L or R inputs System Gain Signal to Noise SNR-A-Weighted SNR-unweighted
245 0.5 0.2 10 >50
Watts % % mV-DC DF
240 1 0.3 30 20
22k filter 22k filter @ Speaker Outputs Measured at amplifier board Measured at the speaker cable. 189 Watts @ THD < 0.1 % @ 50 Hz
50 11 11 45
Hz mVrms mVrms dB
50 Nominal Freq. ±1dB To 1 Watt ±1dB To 1 Watt Reference
Single input driven Single input driven, LFE switch ON Single input driven Normal or LFE mode
80 65
dBA dBr
75 60
Residual Noise Floor Input Impedance Line Input (L, R,LFE) Filters LP filter Variable Subsonic filter (HPF) 2nd Order Friend circuit LFE Low pass Limiter
<2.0 mVrms(max)
2.5
relative to 1W relative to 1W Volume @max, w/ A/P Swept Bandpass Measurement (Line freq.+ harmonics) (BW=20 KHz)
A-Weighting filter 22K filter Line level inputs must be terminated using 1KOHM
10K
ohms
n/a
Nominal
50-150 Fixed Fixed 200>LP<500
Hz
± 10
4th Order variable-24 db/Octave
Hz
LFE input driven only
THD at Max. Output Power Features Volume pot Taper (lin/log) Phase switch LP Filter defeat switch LED indicator Input Configuration Line In (L,R) & LFE Signal Sensing (ATO) Auto-Turn-On (yes/no) ATO Input test frequency ATO Level LFE Input ATO Turn-on time Auto Mute/ Turn-OFF Time Power on Delay time --
13
%
Drive unit 6dB above the required level to obtain full power Maximum THD as a result of limiting. functional Approximately 208mV
LOG 0-180 YES YES
-deg
functional functional functional functional
A Taper Disables LP filter, intended for LFE Bicolor LED located in top of the cabinet, RED-Standby, GRN-Active
YES
--
functional
Dual RCA jack, for LFE use either L or R inputs
YES 50 2 5 5-15 3
Hz mV ms minutes sec.
functional functional functional Amp connected and AC on, then functional input signal applied T before muting, after signal is 5-15 removed 4 After AC Power is applied
Maximum acceptable level.
Auto turn of time (T) must be 5 > T < 15 Minutes
2
ES150P
Parameter Transients/Pops ATO Transient Turn-on Transient Turn-off Transient Efficiency Efficiency Efficiency at 1/8 of rated power Off state input power 61 45 12 % % Watts 60 42 14 Test conducted at rated power 250W Test conducted at 31.25 WRMS Nominal Line voltage Nominal Line voltage-Rated impedance 4 Ohms Nominal Line voltage RED LED Maximum allowable input power under nominal Input voltage and frequency, HOT or COLD operation. LED GREEN no signal applied 225 Watts @ 4 Ohms nominal line voltage 0.5 0.5 0.5 V-peak V-peak V-peak 0.5V 0.8V 0.8V @ Speaker Output @ Speaker Output @ Speaker Output Amplifier activated by signal presence at the Line input AC Line cycled from OFF to ON AC Line cycled from ON to OFF Specification Unit QA Test Limits Conditions Notes
Stand-by Input Power Power Cons. @ rated power Protections Short Circuit Protection
18 367
Watts Watts
18 375
@ nom. line voltage @ nom. line voltage
YES
Thermal Protection
YES
DC Offset Protection Line Fuse Rating USA-Domestic EU
YES 3.15 2 Amps Amps
Amplifier should resume operation after short circuit condition removal Temperature rise in accessible metal parts should not exceed 35K rise for domestic @1/8 max unclipped Power at version or 30K rise for European versions functional 1.06 times the input voltage (refer to requirements sheet). Design must insure no Offset at the speaker output under any operating condition DC present at Speaker Out leads including abnormal operation functional Direct short at output 3.15 2 Type-T or Slo Blo-250 V Type-T or Slo Blo-250 V, Low Breaking capacity Internal fuse with UL/SEMKO rated holder Internal fuse with UL/SEMKO rated holder
Other Parameters/Notes: 1. Limiter circuit response must be clean sounding with no apparent pops, noises, or pumping. 2. Plate dimensions not to exceed 11.81"H x 7.87"W and the plate must be airtight with no possibility of air leaks (plastic cover required). 3. Volume control should be at the input buffer stage in order to lessen the possibility of clipping the input section with highly dynamic audio material. 4. ALL SPECS SHOULD BE MEASURED AT NOMINAL LINE VOLTAGE.
3
ES150P
4
ES150P
CONTROLS AND CONNECTIONS
Rear Panel
¡ Phase Switch TM LFE/Normal Selector £ Subwoofer-Level Control ¢ Crossover Adjustment Line-Level/LFE Input ¡ TM § Power Switch
£
¢
§
AC 120V~60Hz 2A
4
5
ES150P
SYSTEM CONNECTIONS
If you have a Dolby® Digital or DTS® receiver/processor with a low-frequency-effects (LFE) or subwoofer output:
Set LFE/Normal switch to "LFE."
If your receiver/processor does not contain a Dolby Digital or DTS processor, but has subwoofer outputs:
Set line-level/LFE switch to "Normal." NOTE: If your receiver/processor has only one sub out, you may use either the L or R input.
6
5
ES150P
OPERATION
Power On Plug your subwoofer's AC cord into a wall outlet. Do not use the outlets on the back of the receiver. Initially set the Subwoofer-Level Control £ to the "min" position. Turn on your sub by pressing the Power Switch § on the rear panel. Turn on your entire audio system and start a CD or movie soundtrack at a moderate level. Auto On/Standby With the Power Switch § in the ON position, the Status LED on the top will remain lit in red or green to indicate the On/Standby mode of the subwoofer. RED = STANDBY (No signal detected, Amp Off) GREEN = ON (Signal detected, Amp On) The subwoofer will automatically enter the Standby mode after approximately 10 minutes when no signal is detected from your system. The subwoofer will then power ON instantly when a signal is detected. During periods of normal use, the Power Switch § can be left on. You may turn off the Power Switch § for extended periods of nonoperation, e.g., when you are away on vacation. Adjust Gain Turn your Subwoofer-Level Control £ up to the halfway position. If no sound emanates from the subwoofer, check the AC-line cord and input cables. Are the connectors on the cables making proper contact? Is the AC plug connected to a "live" receptacle? Has the Power Switch § been pressed to the "On" position? Once you have confirmed that the subwoofer is active, proceed by playing a CD, record or cassette. Use a selection that has ample bass information. Set the overall volume control of the preamplifier or stereo to a comfortable level. Adjust the Subwoofer-Level Control £ until you obtain a pleasing blend of bass. Bass response should not overpower the room but rather be adjusted so there is a harmonious blend across the entire musical range. Many users have a tendency to set the subwoofer volume too loud, adhering to the belief that a subwoofer is there to produce lots of bass. This is not entirely true. A subwoofer is there to enhance bass, extending the response of the entire system so the bass can be felt as well as heard. However, overall balance must be maintained or the music will not sound natural. An experienced listener will set the volume of the subwoofer so its impact on bass response is always there but never obtrusive. Phase Control The Phase Switch ¡ determines whether the subwoofer speaker's pistonlike action moves in and out with the main speakers, 0°, or opposite the main speakers, 180°. Proper phase adjustment depends on several variables such as room size, subwoofer placement and listener position. Adjust the phase switch to maximize bass output at the listening position. Crossover Adjustment The Crossover Adjustment Control ¢ determines the highest frequency at which the subwoofer reproduces sounds. If your main speakers can comfortably reproduce some low-frequency sounds, set this control to a lower frequency setting, between 50Hz and 100Hz. This will concentrate the subwoofer's efforts on the ultradeep bass sounds required by today's films and music. If you are using smaller bookshelf speakers that do not extend to the lower bass frequencies, set the Crossover Adjustment control to a higher setting, between 120Hz and 150Hz. NOTE: This control will have no effect if the LFE/Normal Selector TM is set to LFE. If you have a Dolby Digital or DTS processor/receiver, the Low-Pass Frequency is set by the processor/receiver. Consult your owner's manual to learn how to view or change this setting.
MAINTENANCE AND SERVICE
The enclosure may be cleaned using a soft cloth to remove fingerprints or to wipe off dust. The grille may be gently vacuumed. Stains may be removed with an aerosol cleaner, following its instructions. Do not use any solvents on the grille. All wiring connections should be inspected and cleaned or remade periodically. The frequency of maintenance depends on the metals involved in the connections, atmospheric conditions and other factors, but once per year is the minimum. If a problem occurs, make sure that all connections are properly made and clean. If a problem exists in one loudspeaker, reverse the connection wires to the left and right system. If the problem remains in the same speaker, then the fault is with the loudspeaker. If the problem appears in the opposite speaker, the cause is in another component or cable. In the event that your subwoofer ever needs service, contact your local JBL dealer, or visit www.jbl.com for a service center near you.
6
7
ES150P
8
ES150P
ES150P Test Set Up and Procedure
Equipment needed: · Function/signal generator/sweep generator · Integrated Amplifier · Multimeter · Speaker cables General Unit Function (UUT = Unit Under Test) 1) From the signal generator, connect line level (RCA) cables to the Subwoofer Line Level Input jacks L/R on the UUT. Use a Y-cable from a mono source if necessary to connect to both inputs. 2) Turn the CROSSOVER control to maximum (150). 3) Turn the LEVEL control on the UUT to completely counterclockwise (MIN). 4) LFE/NORMAL switch should be in NORMAL position. 5) PHASE switch position does not matter. 6) Turn on generator; adjust to 75mV, 50 Hz. 7) Plug in UUT; turn the power switch ON. LED should switch from Red to Green. 8) Turn LEVEL control full clockwise (MAX); immediate and vigorous bass response should be heard and felt from port tube opening on the bottom. 9) Turn off generator, turn LEVEL control full counterclockwise (MIN), and disconnect RCA cable. Sweep Function 1) Follow steps 1-8 above, using a sweep generator as a signal source. 2) Sweep generator from 20Hz to 300Hz. Listen to the cabinet and drivers for any rattles, clicks, buzzes or any other noises. If any unusual noises are heard, remove woofer and test. Driver Function 1) Remove woofer from cabinet; detach + and - wire clips. 2) Check DC resistance of woofer; it should be 3.4 ohms ±10% 3) Connect a pair of speaker cables to driver terminals. Cables should be connected to an integrated amplifier fed by a signal generator. Turn on generator and adjust so that speaker level output is 5.0V. 4) Sweep generator from 20Hz to 1kHz. Listen to driver for any rubbing, buzzing, or other unusual noises.
9
ES150P
10
ES150P
11
ES150P
ES150P Troubleshooting Testing Flow Chart
Start yes Test protection Dc voltage check ±Vcc,±15V O no O yes Power on check LED red &green Check vol module no O yes no Test frequency Response O yes Check U102,uR133, C121,R135,C122.etc yes Test phase sw,low pass sw rabos vr O yes Listening test no O yes Test input sensitivity no O Check U101,R117, R112,R114 etc
12
no Check transformer C168,C169,D123, D124,C170 yes Test limiter circuit
Check U107.R237 ±15Vcc etc
no O yes & connector cable& ±15V.etc Check THD output power, noise
Check U106.Q107etc
Check pre board & power board , ±Vcc,±15V etc
no O
Auto off Function Hi pot test Check U103.Q101. Q102.C131.R142;Ac cord, Transformer.
no
Check sw103,102, R158,163,177 etc
no O yes The Amp ass'y ok END
ES150P
13
ES150P
14
ES150P
15
ES150P
16
ES150P
17
ES150P
ES150P (120v) Electrical Parts List
Part Number Description Qty Reference Designator
INPUT/PREAMP PCB & DAUGHTER BOARD PCB
Resistors 110-14392J26-E 110-16000j26-e 110-16101J26-E 110-16102J26-E 110-16103J26-E 110-16105J26-E 110-16151J26-E 110-16183J26-E 110-16203J26-E 110-16221j26-e 110-16223J26-E 110-16274j26-e 110-16432j26-e 110-16472J26-E 110-16473J26-E 110-16474j26-e 110-164r7j26-e 116-161002f26-e 116-161212f26-e 116-161243F26-E 116-161271F26-E 116-161504f26-e 116-162001f26-e 116-162002f26-e 116-162051f26-e 116-162212f26-e 116-162553F26-E 116-162611f26-e 116-162803f26-e 116-163011f26-e 116-164421f26-e 116-164751f26-e 116-164752f26-e 116-164871F26-E 116-164991f26-e 116-166491f26-e 116-168252F26-E 116-169091f26-e 115-h103a101-e 115-h503b405-e
Capacitors
CARBON RESISTOR 3.9K 1/4W ±5% CF (RoHS) CARBON RESISTOR 0 1/6W ±5% CF (RoHS) CARBON RESISTOR 100 1/6W ±5% CF (RoHS) CARBON RESISTOR 1K 1/6W ±5% CF (RoHS) CARBON RESISTOR 10K 1/6W ±5% CF (RoHS) CARBON RESISTOR 1M 1/6W ±5% CF (RoHS) CARBON RESISTOR 150 1/6W ±5% CF (RoHS) CARBON RESISTOR 18K 1/6W ±5% CF (RoHS) CARBON RESISTOR 20K 1/6W ±5% CF (RoHS) CARBON RESISTOR 220 1/6W ±5% CF (RoHS) CARBON RESISTOR 22K 1/6W ±5% CF (RoHS) CARBON RESISTOR 270K 1/6W ±5% CF (RoHS) CARBON RESISTOR4.3K 1/6W ±5% CF (RoHS) CARBON RESISTOR 4.7K 1/6W ±5% CF (RoHS) CARBON RESISTOR 47K 1/6W ±5% CF (RoHS) CARBON RESISTOR 470K 1/6W ±5% CF (RoHS) CARBON RESISTOR 4.7 1/6W ±5% CF (RoHS) METAL FILM RESISTOR 10K 1/6W ±1% MF (RoHS) METAL FILM RESISTOR 12.1K 1/6W 1% MF (RoHS) METAL FILM RESISTOR 1/6W 124K ±1% MF (RoHS) METAL FILM RESISTOR 1.27K 1/6W ±1% MF(RoHS) METAL FILM RESISTOR 1.5M 1/6W ±1% MF (RoHS) METAL FILM RESISTOR 2.00K 1/6W ±1% MF METAL FILM RESISTOR 20.0K 1/6W ±1% MF (RoHS) METAL FILM RESISTOR 2.05K 1/6W MF (RoHS) METAL FILM RESISTOR 22.1K 1/6W ±1% MF (RoHS) METAL FILM RESISTOR 255K 1/6W±1% MF (RoHS) METAL FILM RESISTOR 1/6W 2.61K 1% (RoHS) METAL FILM RESISTOR 280K 1/6W±1% MF (RoHS) METAL FILM RESISTOR 3.01K 1/6W±1% MF (RoHS) METAL FILM RESISTOR 4.42K 1/6W ±1% MF (RoHS) METAL FILM RESISTOR 4.75K 1/6W MF (RoHS) METAL FILM RESISTOR 47.5K 1/6W ±1% MF (RoHS) METAL FILM RESISTOR 4.87K 1/6W ±1% MF (RoHS) METAL FILM RESISTOR 4.99K 1/6W ±1% MF (RoHS) METAL FILM RESISTOR 6.49K 1/6W ±1% MF (RoHS) METAL FILM RESISTOR 82.5k 1/6w ±1% MF(RoHS) METAL FILM RESISTOR 9.09K 1/6W±1% MF (RoHS) VARIABLE RESISTOR A10K (RoHS) LEVEL VARIABLE RESISTOR B50K (RoHS) CROSSOVER
1 1 4 1 7 1 1 1 1 2 2 1 1 1 1 1 1 3 1 1 1 1 1 1 1 6 1 1 1 1 2 3 2 1 1 2 1 4 1 1
R150, R191, R112,R113,R151,R152, R140, R263,R118,R133,R136,R146,R149,R199, R145, R139, R147, R200, R119,R120, R141,R148, R138, R254, R144, R137, R143, R153, R130,R131,R132, R188, R190, R251, R142, R202, R193, R252, R209,R231,R232,R296,R204,R206, R195, R253, R201, R194, R205,R207, R109,R110,R134, R121,R122, R189, R265, R114,R115, R135, R197,R198,R173,R178, R286 R233
129-a222j633-e 129-a273j633-e 129-a274j633-e 129-a473j633-e 129-a563j633-e 129-a823j633-e 130-2b221k503-e 130-3f104z503-e 130-3f473m503-e 130-sl101k503-e 130-sl330ja03-e 130-sl470k503-e 135-3105m50-e 135-3106m50-e
METALIZED CAP. 0.0022u 63V ±5% MSC (RoHS) METALIZED CAP 0.027uF 63v ±5% MSC(RoHS) METALIZED CAP 0.27uf 63V ±5% (RoHS) METALIZED CAP 0.047U 63V ±5% MSC (RoHS) METALIZED CAP 0.056uF 63V ±5% MSC (RoHS) METALIZED CAP 0.082U 63V ±5% MSC (RoHS) DISC CAPACITOR 220P 50V ±10% (RoHS) DISC CAPACITOR 0.1U 50V +80/-20% (RoHS) DISC CAPACITOR 0.047U 50V ±20% (RoHS) DISC CAPACITOR 100P 50V SL ±10% (RoHS) DISC CAPACITORS 33P 100V±5% (RoHS) DISC CAPACITOR 47P 50V ±10% (RoHS) ELECTROLYTIC 1U 50V ±20% (RoHS) ELECTROLYTIC 10uF 50V ±20% (RoHS)
C181,C182, C209,C218, C121,C122, C138, C149,C137,C143, C201,C213,C142, C107,C108, C112,C114,C124,C125,C130,C133,C135, 13 C144, C145,C153,C154,C232,C233, 1 C180, 1 C120, 1 C148, 1 C128, 1 C126, 4 C109,C111,C123,C129,
2 2 2 1 3 3 2
18
ES150P
Part Number Description Qty Reference Designator
INPUT/PREAMP PCB & DAUGHTER BOARD PCB
135-3107m16-e 135-3107m25-e 135-3226m50-e 139-3227m16-e 129-a473j633-e Semiconductors 192-027c1815gr-e 197-631n4148-e 199-55000395-e 190-06m4558d-e 190-16tl072n-e 190-16tl074cn-e 192-153j111-e
Miscellaneous
ELECTROLYTIC 100uF 16V ±20% (RoHS) ELECTROLYTIC 100U 25V ±20% (RoHS) ELECTROLYTIC 22U 50V ±20% (RoHS) LOW LEAKAGE EC 220uF 16V ±20% (RoHS) METALIZED CAP. 0.047U 63V ±5% MSC (RoHS)
5 1 1 1 1
C113,C115,C132,C134,C136, C152, C151, C131, C150
transistor 2SC1815GR TOSHIBA(RoHS) NPN DIODE 500mW 75V 1N4148 Panjit (RoHS) ZENER DIODE 3.9V 1/2W 52mm (RoHS) I.C. OPA 4558D (RoHS) DUAL OP-AMP I.C. TL072N @6.5 (RoHS) DUAL OP-AMP I.C TL074CN ST (RoHS) QUAD OP-AMP FET J111 FAIRCHILD TO-92 (RoHS)
3 7 1 2 1 2 1
Q101,Q102,Q103, D105,D106,D108,D109,D110,D112,D113, D130, U101,U103 U105 U102,U106 Q107
175-1c02v01-e 175-9f40hr2-e 180-T000TS81-E 362-FE-00041-0LAE 162-10169003-e 162-50122004-e 174-0rcb202vag-e
WIRE CONNECTOR&BASE 2PIN PITCH=2.5mm (RoHS)
WIRE CONNECTOR&BASE 40PIN PITCH=2.54mm HR2*40 (RoHS)
TACT SWITCH T2 T8019L-SNQ-E-H+U PHASE, LFE/NORMAL
PCB holder 11.75*8.5*12.5H(RoHS) WIRE ASS'Y160mm AWG28 WHITE/BLK (RoHS) WIRE ASS'Y 120mm RED/WHT 2PIN (RoHS) RCA JACK RCA-209 WITH GOLD (RoHS) INPUT
1 0.5 2 1 1 1 1
P106 D201 SW102,SW103 P105 D201 JK102
MAIN PCB
Resistors 110-12621j15-e 110-20152j20-e 113-50r10j10-e 116-142003f26-e 110-16102J26-E 110-16103J26-E 110-16153j26-e 110-16182j26-e 110-16222J26-E 110-16223J26-E 110-16274j26-e 110-16333j26-e 110-16391j26-e 110-16472J26-E 110-16473J26-E 110-16683j26-e 112-14101j26-e 116-141r00j26x-e 116-161002f26-e 116-161301f26-e 116-161692f26-e 116-162001f26-e 116-162492f26-e 116-166813f26-e
Capacitors
CARBON RESISTOR 620 1/2W ±5% 15mm (RoHS) CARBON RESISTOR 1.5K 2W ±5% CF 20mm KINK(RoHS) CEMENT RESISTOR 0.1 5W ±5% (RoHS) METAL FILM RESISTOR 200K 1/4W ±1% MF (RoHS) carbon resistor 1K 1/6W ±5% CF (RoHS) carbon resistor 10K 1/6W ±5% CF (RoHS) carbon resistor 15K 1/6W ±5% CF (RoHS) carbon resistor 1.8K 1/6W ±5% CF (RoHS) carbon resistor 2.2K 1/6W ±5% CF (RoHS) carbon resistor 22K 1/6W ±5% CF (RoHS) carbon resistor 270K 1/6W ±5% CF (RoHS) carbon resistor 33K 1/6W ±5% CF (RoHS) carbon resistor 390 1/6W CF (RoHS) carbon resistor4.7K 1/6W ±5% CF (RoHS) carbon resistor 47K 1/6W ±5% CF (RoHS) carbon resistor 68K 1/6W ±5% CF (RoHS) fuseresistor 1/4W 100ohm 5% (RoHS) metal film resistor 1.00 1/4W±5% MO (fireproofing resistor ) metal film resistor 10K 1/6W ±1% MF (RoHS) metal film resistor 1.30K 1/6W MF (RoHS) metal film resistor 16.9K 1/6W MF (RoHS) metal film resistor 2.00K 1/6W ±1% MF (RoHS) metal film resistor 24.9K 1/6W ±1% MF (RoHS) metal film resistor 681K 1/6W ±1% MF (RoHS)
1 1 2 1 3 9 2 1 2 3 1 1 2 4 1 1 2 2 2 3 1 1 2 1
R238, R208, R224,R225, R209, R210,R239,R264, R216,R227,R229,R230,R231,R232,R233, R260, R261, R247,R249, R248, R242,R245, R218,R220,R223, R240, R211, R243,R246, R213,R217,R219,R222, R221, R212, R241,R244, R255,R256, R234,R235, R226,R228,R236, R214, R215, R257,R258, R262,
135-4228m35-e 138-5478m80-e 130-2b102k503-e 130-3f104z503-e 130-ch101j503-e
ELECTROLYTIC CAP. 2200uF 35V ±20%(RoHS) LARGE ALUMINUM EC 4700uF 80V ±20%85 (RoHS) DISC capacitor 1000P 50V ±10% (RoHS) DISC capacitor 0.1U 50V +80/-20% (RoHS) DISC capacitor 100P 50V ±5% (RoHS)
2 2 1 2 2
C170,C171, C168,C169, C165, C163,C164, C159,C160,
19
ES150P
Part Number Description Qty Reference Designator
MAIN PCB
135-3107m16-e 135-3226m50-e 135-3227m10-e 139-3227m16-e 140-RX473KB03-E 140-rx103ka03-e Semiconductors 190-16lm324n-e 192-991d669a-e 192-992b649t-e 197-00DB103G-E 197-00kbu1003-e 197-101n4002-e 190-16l431clp1-e 192-027c1815gr-e 192-028a1015gr-e 192-1572n5551-e 192-1582n5401-e 197-631n4148-e 199-65000563g-e 199-65001503g-e 199-65002003g-e
Miscellaneous
electrolytic cap 100uF 16V ±20% (RoHS) electrolytic cap 22U 50V ±20% (RoHS) electrolytic cap 220U 10V ±20% (RoHS) low leakage ec 220uF 16V±20% (RoHS) multi layer cap 47NF 200V X7R ±10% (RoHS) multi layer cap 10nF 100V X7R 10% (RoHS)
2 2 2 1 2 1
C166,C167, C161,C162, C156,C157, C155, C172,C173, C174,
I.C. LM324N (RoHS) QUAD OP-AMP transistor HI-SINCERITY HSD669A (RoHS) NPN transistor HSB649T (RoHS) PNP DIODE 1A 200V DF02MDB103G (RoHS) BRIDGE DIODE 10A 200V KBU1003(RoHS) BRIDGE DIODE1N4002TB (RoHS)
IC TL431CLP (RoHS) PROGRAMMABLE VOLTAGE REFERENCE
transistor 2SC1815GR TOSHIBA(RoHS) NPN transistor 2SA1015GR TOSHIBA(RoHS) PNP transistor FSC 2N5551 (RoHS) NPN transistor FSC 2N5401 AI-PNP 350V500mA TO-92 (RoHS) dilde500mW 75V 1N4148 Panjit (RoHS) ZENER diode GDZJ5.6B 500mW 5.6V 2% (RoHS)
ZENER diode GDZJ15C500mW 15V 2%ROHM 52mm 1N5245B
ZENER diode GDZJ20D 500mW 20V 2% (RoHS)
1 1 1 1 1 1 1 4 3 1 1 7 1 1 1
U107, Q116, Q118, D124, D123, D114, D115 Q110,Q112,Q114,Q117, Q111,Q113,Q115, Q109, Q108, D117,D118,D119,D120,D121,D126,D125, D116, D122, D129,
109-1tsc103j0-e 175-1c02v01-e 175-1c06v01-e 175-1d02v01-e 175-1d05v01-e 362-FE-00041-0LAE 171-udhss124d-e
THERMISTOR TSC05103J (RoHS) WIRE CONNECTOR&BASE 2PIN PITCH=2.5mm (RoHS) WIRE CONNECTOR&BASE 6 PIN PITCH=2.5mm(RoHS) WIRE CONNECTOR&BASE 2PIN PITCH=3.96mm(RoHS) WIRE CONNECTOR&BASE 5PIN 3.96mm (RoHS) PCB SUPPORT 11.75*8.5*12.5H(RoHS) RELAY 5A 24V UDH-SS124D(RoHS)
1 1 1 1 1 1 1
R237, P108, P107, P112, P113, K101,
CLASS D PCB ASS'Y (RECOMMENDED REPLACE ENTIRE MODULE PART# 051-A05102C-E)
Resistors 118-12061001f-e 118-12061002f-e 118-12061002j-e 118-120610r0j-e 118-12061501f-e 118-12062002f-e 118-12062201j-e 118-12062204j-e 118-12062211f-e 118-12062550f-e 118-12062701j-e 118-12063300j-e 118-12063301j-e 118-12063321f-e 118-12063922f-e 118-12064700j-e 118-12064701j-e 118-12064751f-e 112-10180j00-e
Capacitors
SMD resistor 1K 1206 1% (RoHS) SMDresistor 10K 1206 1% (RoHS) SMDresistor 10.0K 1206 5% (RoHS) SMDresistor 10.0 1206 5% (RoHS) SMDresistor 1.5K 1206 1% (RoHS) SMDresistor 20K 1206 1% (RoHS) SMDresistor 2.20K 1206 5% (RoHS) SMDresistor 2.20M 1206 5% (RoHS) SMDresistor 2.21K 1206 1% (RoHS) SMD resistor 1206 255 1% (RoHS) SMDresistor 2.70K 1206 5% (RoHS) SMDresistor 330 1206 5% (RoHS) SMDresistor 3.30K 1206 5% (RoHS) SMDresistor 3.32K 1206 1% (RoHS) SMDresistor 1206 39.2K±1% (RoHS) SMDresistor 470 1206 5% (RoHS) SMDresistor 4.70K 1206 5% (RoHS) SMDresistor 4.75K 1206 1% (RoHS) FUSE RESISTOR FMF 1W 18 5%(RoHS)
R2, R25, R29,R30,R30B,R7,R9, R20,R20B,R22,R23, R31,R32,R35,R36,R39,R40,R41,R42,R43, 12 R44,R45,R46, 1 R26, 8 R13,R16,R33,R34,R37,R38,R14,R15, 1 R4, 1 R6, 1 R24, 1 R10, 1 R21, 2 R27,R28, 1 R1, 1 R3, 2 R8,R11, 1 R12, 1 R5, 1 R47
1 1 5 4
128-e106ma01-se
CROSSVER CAP. 10uF 100V 20% of shi xi (RoHS)
2
C16,C17,
20
ES150P
Part Number Description Qty Reference Designator
CLASS D PCB ASS'Y (RECOMMENDED REPLACE ENTIRE MODULE PART# 051-A05102C-E)
130-sl681kb03-e 132-104kb50-e 141-D7104KA0-E 141-D7104KB5-E 141-c0101k50-e 141-c0220k50-e 141-c0561k50-e 141-c5104m50-e 141-c7103k50-e 132-105kb50-e Semiconductors 192-232irf9640-e 192-233f640n-e 190-16tl072dts-e 192-09124126qs-e 192-09139066rs-e 192-091sc4672-e 192-09210376qs-e 192-09215146rs-e 192-1582n5401-e 197-03rls4148s-e 199-15000563s-e 199-1500120s-e
Miscellaneous
DISC CAPACITOR SL 680PF 200V (RoHS)
MYLAR CAPACITOR 0.1U ±10% 250V long LS-10.mm MD (RoHS)
SMDcapacitor 0.1uF 100V 10%1210 X7R (RoHS) SMDcapacitor 0.1uF 250V 10%1210 X7R (RoHS) SMDcapacitor 100pF 50V 10%1206 NP0 (RoHS) SMDcapacitor 22pF 50V 10% 1206SMT NPO (RoHS) SMDcapacitor 560pF 50V 10%1206 NPO (RoHS) SMDcapacitor1206 Y5V 0.1uF50V ±20% (RoHS) SMD capacitor 10nF 50V 1%1206 X7R (RoHS) MYLAR CAPACITOR 1uF 250V ±10% long (RoHS)
1 1 2 2 1 1 1 8 1 1
C21 C20, C18,C19, C12,C14, C4, C5, C6, C2,C3,C7,C8,C9,C10,C11,C15, C13, C40,
FET IRF9640 IR P-CH TO220(RoHS) TRANSISTOR IRF640N INTERNATIONAL(RoHS) SMD I.C. TL072CDT SGS THOMSON(RoHS) DUAL OP-AMP SMD transistor 2SC2412K-T146Q/RROHM (RoHS) SMD transistor 2SC3906K-T146R ROHM(RoHS) transistor 2SC4672(MPT3) ROHM(RoHS) SMD transistor 2SA1037K-T146Q/RROHM (RoHS) SMD transistor 2SA1514K-T146R ROHM(RoHS) transistor FSC 2N5401 AI-PNP 350V500mA TO-92 (RoHS) *SMD DIODE RLS4148-TE11 ROHM(RoHS) SMD ZENER 5.6V 5% PHILIPSBZX84-C5V6 (RoHS) SMD ZENER 12V 5% PHILIPSBZX84-C12 (RoHS)
2 1 1 2 2 1 2 1 1 8 2 4
Q10,Q10B, Q11, IC1, Q1,Q4, Q2,Q8, Q5B, Q7,Q9, Q3, Q6B, D1,D2,D3,D4,D5,D5B,D6,D20, Z1,Z2, Z3,Z4,Z5,Z6,
175-9F02H02-E 175-9F03H020-E 122-13151k0190-e 122-14300k4-e
WIRE CONNECTOR&BASE 2PIN PITCH=2.54mm(RoHS) WIRE CONNECTOR&BASE 3PIN PITCH=2.54mm(RoHS) CHOKE SA-500-280(PT1601B*151MAA) (RoHS) Ferrite core LD1215*300KU±10% (RoHS)
1 2 1 1
HDR3, HDR1,HDR2, L1, L2,
MISC./MECHANICAL & AC INPUT PCB
128-C117JA01-E electrolytic CAP 110uf 100V 150-R0905505-E POWER TRANSFORMER 115V/60Hz 300W(RoHS) 152-u60201a06-e LINE CORD 6FT UL 2PIN WITH PLASTIC BAG (RoHS) 153-vpst101s2-e AC OUTLET&SOCKET VDE 2PINS INLETSOCKET PRONIC 154-k30005t0-e FUSE 3A 250V 30mm UL/CSA(RoHS) 155-630r345b-e FUSE HOLDER UL/CSA 6*30mm R3-45B (RoHS) 162-10100023-e WIRE UL/CSA 1617 #22 100mmBLK (RoHS) 162-10151001-e WIRE UL1617 150mm 22AWG BROWN6:6 (RoHS) 162-5016d001-e WIRE 24# 160mm BLK (RoHS) 162-5020d006-e WIRE UL2468 200mm 2.5mmpitchRED/WHT (RoHS) 162-a055d002-e WIRE ASS'Y 550mm UL2468 26AWG RED/WHT5LED(RoHS) 166-5070a4bd-e SPKER WIRE 700mm #18 #205*0.5tBLK/#250*0.8t RED(RoHS) 180-prf1003b-e SWITCH ROCK RF-1003-BB210(RoHS) POWER 193-0s4211-e INSULATOR (INSULATION SPACER)42*11 (RoHS) 193-201612tr-e INSULATOR T0-220 16mm*12mm(RoHS) 302-AL-05123-0BAE REAR BOARD300*200*2.5 BLK ES150P/120V USE (RoHS) 306-ABS-05081-0BAE REAR HOUSMG 198*298*102mm WITH 8piece EVA (RoHS) 311-ABS-00028-0BAE KNOB 46077-W P.V.C.(RoHS) LEVEL, CROSSOVER 323-AL-05000-0LAE HEAT SINK (RoHS) 325-FE-00400-0LAE PCBFLOOR STAND 58*9*13.5T (RoHS) 333-EVA-00188-0BAE EVA GASKET 170x5x1t WITH GLUE (RoHS) 333-EVA-00220-0BAE EVA GASKET LONG 225*15*1t UL(RoHS) 333-EVA-00866-0BAE FIREPROOFING EVA 48*18*1.5T (RoHS) 333-SPG-00860-0BAE FIREPROOFING EVA 450*50*5T (RoHS) 335-NYL-00002-0BAE WIRE CLIP 4K-4 NO-BB(RoHS) 336-RUB-05103-0BAE RUB PAD 97*16*3.0T BLK (RoHS) 350-EM04012D024-E 4*12WOOD SCREW BLK (RoHS) 351-AM03008A078-E M3*8 MACHINE SCREW CROSS WITH NICKEL (RoHS) 1 1 1 1 1 1 1 1 1 1 1 1 1 1 3 1 1 2 1 1 1 1 1 1 1 2 4 4 On Woofer terminals
21
ES150P
Part Number Description Qty Reference Designator
MISC./MECHANICAL & AC INPUT PCB
351-AM03008A079-E M3*8 MACHINE SCREWCROSS BLK (RoHS) 351-AM03018A905-E MACHINE SCREW M3.0*18 CROSS with nickel (RoHS) 351-HM03006A1258-EMACHINE SCREW M3*6mm CROSS with nickel (RoHS) 351-HM04010A217-E M4*10 MACHINE SCREWCROSS BLK(RoHS) 352-AM03008D040-E 3*8 B TYPE PING SCREW CROSS BLK (RoHS) 352-AM03008D041-E 3*8 B TYPE PING SCREWCROSS WITH NICKEL (RoHS) 352-AM03010D065-E 3*10 P TYPE PING SCREWCROSS BLK (RoHS) 352-BM03010D064-E 3*10 B TYPE PING SCREWCROSS BLK (RoHS) 355-P07049-E WASHER 7.2*12*0.5t COLOR (RoHS) 361-FE-00002-0LAE HOLDER 90*70*15mm (RoHS) 361-FE-05016-0LAE SECC HOLDER 36*12.5*8.5 (RoHS) 362-FE-00013-0LAE PCB HOLDER L TYPE t=1.6mmS.P.C.C 89*9*1.6T (RoHS) 7 2 1 4 2 2 1 2 2 1 1 1
22
ES150P
23
ES150P
24
ES150P
25
ES150P
26
ES150P
27
ES150P
28
ES150P
29
ES150P
30
ES150P
31
ES150P
32
ES150P
33