Text preview for : Jbl-L8400P actsub.pdf part of JBL L8400P active subwoofer
Back to : Jbl-L8400P actsub.pdf | Home
Studio L Series
L8400P
Amplifier/Subwoofer
SERVICE MANUAL
JBL Consumer Products 250 Crossways Park Dr. Woodbury, New York 11797 Rev1 3/2006
L8400P L series
- CONTENTS BASIC SPECIFICATIONS..................................................1 PACKAGING..................................................................2 DETAILED SPECIFICATIONS...........................................3 CONNECTIONS............................................................. 5 OPERATION ..................................................................7 BASIC TROUBLESHOOTING...........................................8 EXPLODED VIEW..........................................................9 120V BLOCK DIAGRAM..................................................10 PCB DRAWINGS...........................................................11 120V ELECTRICAL PARTS LIST .....................................15 INTEGRATED CIRCUIT/TRANSISTOR PINOUTS.............19 120V SCHEMATICS............................................ .........20
L8400P BASIC SPECIFICATIONS
Amplifier Power (RMS) Peak Dynamic Power * Frequency Response (3dB) Low-Pass Crossover Frequencies Low-Frequency Transducer Baffle Enclosure Inputs 600 Watts 1200 Watts 22Hz Low-pass crossover frequency 50Hz 150Hz, Continuously adjustable 12" (300mm) PolyPlasTM cone Low diffraction, IsoPowerTM Sealed Gold-plated 5-way binding-post speaker-level; Left and right line-level, switchable to LFE Outputs 150Hz when using speaker-level connection Gold-plated 5-way binding-posts Dimensions (H x W x D) 16-1/2" (15-1/2" without feet) x 15-1/2" x 15-1/2" (419mm [394mm without feet] x 394mm x 394mm) Weight 58 lb (26.4kg)
* The Peak Dynamic Power is measured by recording the highest peak-to-center voltage produced by the power amplifier with its limiters disabled, across the output of a resistive load equal to minimum impedance of the transducer, using a 50Hz sine waveburst, 3 cycles on, 17 cycles off. Occasional refinements may be made to existing products without notice but will always meet or exceed original specifications unless otherwise stated
1
L8400P
Packaging
1 3 4 7 8
6
2
6
5
ITEM NO. 1. 2. 3. 4. 5.
DESCRIPTION Owner's Manual Front Grille Warranty Card, JBL 5YR/1YR Kit, Spike Foot L8400P Outer Carton, Black L8400P Outer Carton, Beech L8400P Outer Carton, Cherry
QTY. 1 1 1 4 1 1 1
PART NO. 354038-001 353234-001 338381-001 354432-001 353588-001 353588-002 353588-003
ITEM NO. 6. 7. 8.
DESCRIPTION Pad, Foam, Top, Bottom L8400P Y-Adapter Cable Foot, Bump-On 3M, SJ5744
QTY. PART NO. 2 353592-001 1 354058-001 4 330104-001
2
L8400P L series L8400P Powered Sub/ Plate Amp
LINE VOLTAGE US 120VAC/60Hz EU 230VAC/50-60Hz Yes/No Yes Yes Hi/Lo Line 108-132 207-264 Nom. 120 230 QA Test Limits Unit Vrms Vrms Notes Normal Operation Normal operation, MOMS required
Parameter Amp Section
Spec.
Unit
Conditions
Notes Bridge type amplifier, None of the speaker terminals must be connected to system GND at any time.
Type (Class AB, D, other) Load Impedance (speaker) Rated Output Power THD @ Rated Power THD @ 1 Watt
D 4 450 0.5 0.1
n/a Ohms Watts % %
n/a n/a 380 1 0.2
Nominal 1 input driven 22K filter 22K filter
Measuring 425 Watts Cold
Dynamic Power DC Offset
460 80
Watts mV-DC
450 100
Damping factor Input Sensitivity Input Frequency Left or Right inputs Left & Right with LFE or LP filter OFF Mode selected Speaker/Hi Level Input Signal to Noise SNR-A-Weighted SNR-unweighted SNR rel. 1W-unweighted Residual Noise Floor
>20
DF
15
Power is the average measurement 3/20 Cycles @ 50 Hz, burst test into 4 of the first four consecutive peaks Ohms, input driven 6dB above its maximum of the burst signal sensitivity, volume level at Maximum. @ Speaker Outputs Measured at the speaker cable. 200 Watts, measured at speaker output terminals Measured at amplifier board located at the amp board.
50 16.6 16.6 165
Hz mVrms mVrms mVrms
30 ±2dB ±2dB ±2dB
Nominal Freq. To 1 Watt To 1 Watt To 1 Watt Single input driven, Ap Zo=600 Ohms, LP ON, Volume ctrl & crossover at max Single input driven , Ap Zo=600 Ohms, LP OFF, Volume ctrl & crossover at max Single input driven, Ap Zo=25 Ohms, Normal, Volume ctrl & crossover at max
100 95 70 0.5
dBA dBr dBr mVrms
90 85 65 1
Relative to rated power (400 Watts) A-Weighting filter Relative to rated power (400 Watts) 22K filter Relative to 1W Output 22K filter Volume @max, using RMS reading DMM/VOM (or A/P) Volume @max, w/ A/P Swept Bandpass Measurement (Line freq.+ harmonics)
Residual Noise Floor
0.5
mVrms(max)
1
Speaker input rejection CMRR Speaker in Input Impedance Line Input (L, R,LFE) Speaker/Hi Level Input Filters LP 4th order variable Subsonic filter (HPF) 3rd Orde Low pass filter OFF HP Speaker output 4 Ohms HP Speaker output 8 Ohms Limiter THD at Max. Output Power Features Auto - On -Off >37 dB
1.0V + RMS applied to + & - inputs 50 Hz, Generator GND to system Reference GND
10K 10K
ohms ohms
n/a n/a
Nominal Nominal
50-150 Fixed Fixed 200 100
Hz Hz Hz Hz Hz
± 10 ± 10 ± 20 ± 10 ± 10
L or R input driven, LP Filter OFF Speaker output loaded with 4 Ohms Speaker output loaded with 8 Ohms
YES -YES
n/a
functional
--
functional
No switch to select the ATO mode is provided, Refer to ATO section
3
L8400P L series
Parameter Amp Section Phase switch Volume pot Taper (lin/log) Variable crossover 50-150 Hz HP Speaker out LP On- Off Select switch On-Off indicators Input Configuration Line In (L,R) & LFE Spkr/Hi Level In Signal Sensing (ATO) Auto-Turn-On (yes/no) ATO Input test frequency Min ATO Level L or R Inputs Min ATO Level Speaker in L or R inputs ATO Turn-on time Spec. 0-180 LOG YES YES YES YES Unit deg -QA Test Limits functional functional functional functional functional functional Conditions Notes
5K A Taper 4th Order LP Filter, 2nd order fix and 2nd order variable. Pass through from the speaker input section Disables LP filter, intended for LFE Unit is provided with 2 LED's BLU-ON, REDOFF
--
YES
--
functional
Dual RCA jack, L or R is used in LFE mode
YES
--
functional
Binding post connector L&R
YES 50 3 30 2
Hz mV mV seconds
functional Auto - on selection switch in Auto functional " functional " functional " Amp connected and AC on, then functional input signal applied (T) Time before muting, after minimum ATO signal is removed 17 (3mV) (T) Time before muting, after input 17 signal is removed 4 AC Power Applied
Single input driven Single input driven
Auto Mute/ Turn-OFF Time Auto Mute/ Turn-OFF Time Power on Delay time Transients/Pops ATO Transient Turn-on Transient Turn-off Transient Efficiency Efficiency Stand-by Input Power
5 15 2
minutes Minutes sec.
Auto turn of time (T) must be 5 > T < 17 Minutes Auto turn of time (T) must be 10 > T < 17 Minutes
5 50 50
mV-peak mV-peak mV-peak
n/a @ Speaker Outputs 1V-pk-pk @ Speaker Outputs 1V-pk-pk @ Speaker Outputs
AC Line cycled from OFF to ON AC Line cycled from ON to OFF
68 18
% Watts
65 20
400W of output power @ nominal line voltage, Amp in OFF state, RED LED activated
Stand-by Input Power Power Cons. @ 400W Protection
22 584
Watts Watts
25 615
@ nom. line voltage, Amp in On state, Green LED activated @ nom. line voltage
Nominal Line voltage 120 VAC Maximum allowable input power LED in RED, Class D inactive Maximum allowable input power under nominal Input voltage and frequency, in stand-by mode (HOT or COLD operation, LED GREEN). Class D active but no signal applied. 400 Watts into 4 Ohms nominal line voltage
Thermal Protection DC Offset Protection Line Fuse Rating USA-Domestic EU
YES YES 5 2.5 Amps Amps
functional @1/8 max unclipped Power DC present at Speaker Out leads
Temperature rise in accessible metal parts should not exceed 35K rise for domestic version or 30K rise for European versions (refer to requirements sheet). Unit is protected for over-temperature conditions Relay opens during a DC output condition
Type-T or Slo Blo-250 V Type-T , Low Breaking capacity-250 V Internal fuse with UL/SEMKO rated holder
4
L8400P L series
DOLBY* DIGITAL OR DTS® (OR OTHER DIGITAL SURROUND MODE) CONNECTION IMPORTANT: Make sure that the LFE/Normal toggle switch is in the "LFE" position. This will bypass the subwoofer's normal low-pass filter, reducing the possibility of signal degradation and more accurately reproducing the program materials. However, if your receiver is passing a fullrange signal through its subwoofer output, place the toggle switch in the "Normal" position, which will activate the low-pass filter and protect the subwoofer from possible damage. Connect this jack to the LFE output or subwoofer output on your receiver or amplifier. Connect each speaker to the corresponding speaker terminals on your receiver or amplifier. Make sure that you have configured your surround sound processor for "Subwoofer On." Also, remember to configure your receiver for 5.1-, 6.1- or 7.1-channel operation as appropriate.
Use this installation method for Dolby Digital, DTS or other digital surround processors: Use either the left or right linelevel input jack for the LowFrequency Effects channel; it doesn't matter which one you choose.
DOLBY PRO LOGIC* (NON-DIGITAL) LINE LEVEL Use this installation method for Dolby Pro Logic applications (not Dolby Digital, DTS or other digital processing), where the receiver/processor is equipped with a subwoofer output, or a volume-controlled preamp (line-) level output: Use RCA-type interconnects to connect the line-level subwoofer outputs on your receiver or amplifier to the line-level inputs on the subwoofer. IMPORTANT: Make sure that the LFE/Normal toggle switch is in the "Normal" position. This will activate the subwoofer's lowpass filter, protecting the subwoofer from possible damage and enabling it to operate most efficiently by reproducing only the low-frequency materials that it is best at handling. NOTE: If your receiver or amplifier only has one subwoofer output jack, then you will need to use a Y-connector (not included). Plug the male end of the Y-connector into your receiver or amplifier's subwoofer output jack, and connect each of the two female ends to separate RCAtype interconnects. Finally, plug the RCA-type interconnects into the line-level inputs on the subwoofer. Connect each speaker to the corresponding speaker terminals on your receiver or amplifier. Make sure your receiver or processor is correctly configured to indicate that the subwoofer is "On." Note for advanced users: If your receiver/processor has a built-in low-pass crossover filter for the subwoofer output, you may switch the LFE/ Normal toggle switch to the "LFE" position to bypass the subwoofer's internal crossover.
4
5
L8400P L series
DOLBY PRO LOGIC (NON-DIGITAL) SPEAKER LEVEL Use this installation method for Dolby Pro Logic applications (not Dolby Digital, DTS or other digital processing), where the receiver/processor does not have a subwoofer output, or a volume-controlled preamp (line-) level output: Connect your receiver or amplifier's front left and right speaker terminals to the left and right terminals on the subwoofer that are marked "Speaker Level In." Connect the left and right terminals on the subwoofer that are marked "Speaker Level Out" to the corresponding terminals on the back of your front left and right speakers. Connect your receiver or amplifier's center, surround and surround back speaker terminals to the corresponding terminals on the back of your center and surround speakers.
6
5
L8400P L series OPERATION
Power
Move the Master Power switch ˘ to the "On" position to use the L8400P subwoofer. If you will be away from home for an extended period of time, or if the subwoofer will not be used, switch the Master Power switch ˘ to the "Off" position.
Level Control
The subwoofer Level Control · adjusts the volume of the subwoofer relative to the rest of the system. Proper level adjustment depends on several variables such as room size, subwoofer placement, type of main speakers and position. Adjust the subwoofer level so that the volume of the bass information is pleasing to you.
Crossover Adjustments
The Crossover Frequency Control ¶ determines the highest frequency at which the subwoofer reproduces sounds. If your main speakers can comfortably reproduce some low-frequency sounds, set this control to a lower frequency setting, between 50Hz and 100Hz. This will concentrate the subwoofer's efforts on the ultradeep bass sounds required by today's films and music. If you are using smaller bookshelf speakers that do not extend to the lower bass frequencies, set the low-pass crossover control to a higher setting, between 120Hz and 150Hz. This control is not used when the LFE switch is in the "LFE" position.
6
7
L8400P L series
Phase Control
The Phase Control § determines whether the subwoofer's pistonlike action moves in and out in phase with the main speakers or opposite the main speakers. There is no correct or incorrect setting. Proper phase adjustment depends on several variables such as subwoofer placement and listener position. Adjust the
Phase switch to maximize bass output at the listening position. Remember, every system, room and listener is different. There are no right or wrong settings; this switch offers the added flexibility to adjust your subwoofer for optimum performance for your specific listening conditions without
having to move your speakers. If at some time in the future you happen to rearrange your listening room and move your speakers, you should experiment with the Phase switch in both positions, and leave it in the position that maximizes bass performance.
TROUBLESHOOTING
If you used the high-level (speaker) inputs and there is no sound from any of the speakers: · Check that the receiver/ amplifier is on and a source is playing. · Check that the powered subwoofer is plugged into an active electrical outlet and is switched on. · Check all wires and connections between the receiver/ amplifier and the speakers. Make sure all wires are connected. Make sure none of the speaker wires are frayed, cut or punctured, or touching each other. · Review proper operation of your receiver/amplifier. If there is low (or no) bass output: · Make sure the connections to the left and right "Speaker Inputs" have the correct polarity (+ and ). · Make sure that the subwoofer is plugged into an active electrical outlet and switched on. · Adjust the crossover point. · Flip the Phase Control switch to the opposite position. · If you are using a Dolby Digital/DTS receiver or processor, make sure that the subwoofer and bass management adjustments on the receiver/processor are set up correctly. · Slowly turn the Level Control clockwise until you begin to hear the desired amount of bass. If you used the line-level inputs and there is no sound from the subwoofer: · Check that the receiver/ amplifier is on and a source is playing. · Check that the powered subwoofer is plugged into an active electrical outlet and is switched on. · Check all wires and connections between the receiver/amplifier and the subwoofer. Make sure all wires are connected. Make sure none of the wires are frayed, cut or punctured, or touching each other. · Review proper operation of your receiver/amplifier. · Slowly turn the Level Control clockwise until you begin to hear the desired amount of bass. · Make sure that you have configured your receiver/ processor so that the subwoofer/LFE output is on.
8
7
L8400P
Exploded View
12 5 6 3
4
11
10
7 1 2 8 9
ITEM NO. 1. 2. 3.
DESCRIPTION Woofer Assembly 12" DCR=3.7 ±10% Front Grille Grille Cup, BLK Grille Cup, BE & CH 4. LED Wire Assembly 5. Plate LED 6. Gasket, Plate LED
QTY. 1 1 4 4 1 1 1
PART NO. 353112-001 353234-001 333249-001 333249-003 354288-001 353356-001 353589-001
ITEM NO. 7. 8. 9. 10. 11. 12.
DESCRIPTION QTY. Assembly, Foot 4 Assembly, Logo 1 Screw (Foot) #8 X 1, PB, TRPH CR BLK 8 Screw (Woofer) #8 X 3/4, PB, HXS, ZINC " 8 Screw (Amplifier) #8 X 1, PPH, PB, BLK 12 Screw (LED Plate) #6 X 3/4, PB, HXS, ZINC 4 "
PART NO. 353354-001 353284-001 903101-016 903802-012 900101-016 908302-012
9
L8400P L series
L8400P BLOCK DIAGRAM
10
L8400P L series
NOTE: DESIGNATORS ARE WRONG (SWAPPED) FOR L8 AND L11. BOTH DRAWING AND ACTUAL PCB ON MODEL FIFTEEN
11
L8400P L series
12
L8400P L series
13
L8400P L series
14
L8400P L series
L8400P (120v) ELECTRICAL PARTS LIST
Part Number Description Reference Designator Qty
Main Amp/Supply PCB Resistors 024-000098-120 024-100498-120 024-100598-120 024-100698-120 024-110598-120 024-130498-100 024-150598-120 024-160598-100 024-220298-120 024-220498-120 024-220498-121 024-220598-120 024-330498-120 024-330598-120 024-412498-100 024-470298-120 024-470398-120 024-470598-120 024-510498-120 024-560498-120 024-680498-120 021-100401-020 021-560305-020 022-005105-020 022-470307-020 Capacitors 034-100614-300 034-100625-300 034-100695-300 034-220525-300 034-330625-300 034-470415-300 031-100184-100A 031-100244-100A 031-100344-100A 031-100384-100A 031-220344-300A 031-470144-101A 033-330444-270 033-680464-270 034-150895-201 032-100484-200 Semiconductors 051-000600-100 051-005600-100 051-290700-100 051-540101-000 054-000100-100 054-001002-100 054-001501-100 054-033904-100 054-033906-100 054-050601-100 054-290701-100 Transistor NPN PN:MPSW06RLRA TO-92 (ON)(Q6) Transistor PNP PN:MPSW56RLRA TO-92 (ON)(Q8) Transistor PNP (ON) PN:MPS2907A RLRA TO-92 GR Transistor PNP(FAIRCHILD PN:2N5401 TO-92 (Q3) GS SMD DIODE: PN:ES1D 200V 1A SMD ZENER DIODE PN:BZX84C10 10V SOT-23 (D32) SMD ZENER DIODE PN:BZX84C15 15V SOT-23 (D2,3) SMD Transistor PN:MMBT3904LT1 SOT23 SMD Transistor PN:MMBT3906LT1 SOT23 SMD ZENER DIODE PN:BZX84C5V6 5.6V SOT-23 SMDTransistor (ON) PN:MMBT2907ALT1 SOT-23 (Q52) Q6 Q8 Q12,14,16,18 Q3 D1,23,37,40,44,47 D32 D2,3 Q25,28,29,37,50,51 Q26,27,30,36 D30 Q52 1 1 4 1 6 1 2 6 4 1 1 Electrolytic cap. 100uF/16V M (R)0611 P:2.5 Eletrolytic cap. 100uF/25V M (R)6.3x11 P:5 electrolytic 100uF/63V M (R)1012 P:5 () GR Eletrolytic 22uF/25V M (R)5x11 P:2.5 TAPIN() GS Eletrolytic 330uF/25V M (R)1013 P:5 () Electrolytic cap. 4u7/50V M (R)0511 P:2.0 () SMD Cap. 0u01/250V K 0805 X7R SMD Ceramic Cap. 0u01/50V K 0805 X7R (C27,28) SMD Cap. 0u1/50V K 0805 X7R SMD Cap. 0u1/250V K 1206 X7R (C5,6) SMD Cap. 220pF/50V K 0805 NPO (C40) SMD Cap. 0u0047/50V K 0805 X7R (C1G1) NPE cap. ELYTONE 3u3/50V K10 (R)8x13 SBE NPE cap. ELYTONE 6u8/100V K10 (R)1020 GNE Electrolytic cap. 105 15000uF/63V M (R)3557 P:10mm GS END mylar cap. 1uF/250V K P:15 (C37,39,30) C8 C62 C142 C25,26 C11,100 C7 C104,119 C27,28 C115,135,138C,10,69,112 C5,6 C40 C1G1 C114,137 C113,136 C1,4 C37,39,30 1 1 1 2 2 1 2 2 6 2 1 1 2 2 2 3 GS SMD resistor 0R 1/8W J 0805 SMD resistor 1K 1/8W J 0805 GS SMD resistor 10K 1/8W J 0805 (R8) (R110) () R8 R110 R5,7,16,118,121,122,125,1,126,128,138,165,17 0,168,139 R15,120 R187,188,190,191 R189,192 R20,21 R13,13B R28,29 R119 R17,31 R127 R77,79,22 R4,6,14,60,60B R63 R24-27 R145,155,177,186 R3,171 R48A,48B,48C,48D,48E R30,169 R23 R173 R76 R2 R78 1 1 15 2 4 2 2 2 2 1 2 1 3 5 1 4 4 2 5 2 1 1 1 1 1
GS SMD resistor 100K 1/8W J 0805 (R15,120) SMD resistor 11K 1/8W J 0805 SMD resistor1K3 1/8W F 0805 SMD resistor 15K 1/8W J 0805 (R20,21) SMD resistor 16K 1/8W F 0805 (R13,13B) SMD resistor 22R 1/8W J 0805 (R28,29) SMD resistor 2K2 1/4W J 1206 (R119) SMD resistor 2K2 1/8W J 0805 (R17,31) SMD resistor 22K 1/8W J 0805 (R127) SMD resistor 3K3 1/8W J 0805 (R77,79,22,) SMD resistor 33K 1/8W J 0805 (R4,6,14,60,60B) SMD resistor 4K12 1/8W F 0805 (R63) GS SMD 47R 1/8W J 0805 (R24-27) GS SMD resistor 470R 1/8W J 0805 GS SMD resistor 47K 1/8W J 0805 (R3,171) SMD resistor 5K1 1/8W J 0805 GS SMD resistor 5K6 1/8W J 0805 GS SMD resistor 6K8 1/8W J 0805 (R23) MOF Resistor 1K 1W J FK TYPE MOF resistor 560R 5WS J 8x25 KINK GS Resistor PN:SQM 0R05 5W J 25x13 Resistor KNP 470R 7W J (KNP-700S)
15
L8400P L series
Part Number Description Reference Designator Qty
Main Amp/Supply PCB 054-414803-100ZR 054-540100-100 054-555100-100 051-002301-000 052-400080-000 053-257400-100 Miscellaneous 044-100100-000 025-010300-000 025-210100-000 043-300101-000 043-560200-000 043-700100-000 043-820300-000 072-040008-110 072-040039-000 072-040064-000 072-040096-000 073-111003-000 073-111004-000 074-300018-000 061-700044-000 061-700090-900 063-010010-000 Drive board Resistors 024-000098-120 024-100298-120 024-100498-120 024-100598-120 024-100798-120 024-110598-120 024-200598-120 024-220398-120 024-220498-121 024-220598-120 024-220798-120 024-270498-120 024-390498-120 024-390598-120 024-470398-120 024-470498-120 024-470598-120 024-560598-120 024-680498-120 Capacitors 031-100244-100A 031-100343-100A 031-100344-100A 031-180314-100A 031-470244-102A 031-560243-100A 031-560343-101A 034-100625-303 034-100715-202 034-330615-301 SMD ceramic cap. 0u01/50V K 0805 X7R SMD cap. 100pF/50V J 0805 NPO (C81,84) SMD cap. 0u1/50V K 0805 X7R (85C75-78,82,) SMD cap. 0u18/16V K 0805 X7R (C80,83) SMD cap. 0u047/50V K 0805 X7R (,124C93,94,101) SMD cap. 56pF/50V J 0805 NPO (5,125C92,102,10) SMD cap. 560pF/50V J 1206 X7R (C79) Electrolytic cap. 100uF/25V M (R) P:2.5 (C117) Electrolytic cap. 85 1000uF/16V M (R)1017 P:5 electrolytic cap. 330uF/16V M (R)0812 P:3.5 (C32) C31,140, 108,118,1 C81,84 C85,75-78,82 C80,83 C124,93,94,101 C5,125,92,102,10 C79 C117 C109,132 C32 4 2 6 2 4 4 1 1 2 1 GS SMD resistor 0R 1/8W J 0805 SMD resistor 10R 1/8W J 0805 SMD resistor 1K 1/8W J 0805 GS SMD resistor 10K 1/8W J 0805 GS SMD resistor 1M 1/8W J 0805 SMD resistor 11K 1/8W J 0805 GS SMD resistor 20K 1/8W J 0805 GS SMD resistor 220R 1/8W J 0805 SMD resistor 2K2 1/8W J 0805 (R134) SMD resistor 22K 1/8W J 0805 (R37) GS SMD resistor 2M2 1/8W J 0805 (R87,93) GS SMD resistor 2K7 1/8W J 0805 (R80,84,157) GS SMD resistor 3K9 1/8W J 0805 (R130,161) GS SMD resistor 39K 1/8W J 0805 (R86,94) GS SMD resistor 470R 1/8W J 0805 (R91) GS SMD resistor 4K7 1/8W J 0805 GS SMD resistor 47K 1/8W J 0805 (R35) GS SMD resistor 56K 1/8W J 0805 (R38) GS SMD resistor 6K8 1/8W J 0805 (R135,166) R313,314,318,320 R89,90,140,150 R81,85,96,97,131,137,142,147,162,179 R75,82,83,92,98,132,133,148,163,164,181,156 R32,33 R74,99 R95,141 R136,167 R134 R37 R87,93 R80,84,157 R130,161 R86,94 R91 R151-153,183,34,36 R35 R38 R135,166 4 4 10 12 2 2 2 2 1 1 2 3 2 2 1 6 1 1 2 SMD FERRITE BEAD PN:321611 600R/100MHz 1206 Thermister TSE-103 K L:50mm Thermister (PTC) PN:PTMS2101RP516B (TH2) INDUCTOR PN:YT-10033 30uH (L9,10) INDUCTOR 56uH YT-10779 (L12) INDUCTOR 70uHx2 YT-10024 (L8) INDUCTOR 820uH YT-10034 (L1) 8P Terminal base JS-1001-08 (P1) Terminal (PCB TYPE) PC205 (t=0.8m/m) T205MA Terminal (PCB TYPE) PC250(t=0.8),T250MA Terminal T187MA(PCB TYPE) (t=0.8mm) PC187(0.8) Shorting Strap 54.9x13.6x1mm (J7) Shorting Strap 29.5x12.4x0.8m/m (J4,9) RELAY PN:943-1C-48D (RLY1) Mica 13x18mm TO-220 (Q13,17) Ceramic washer 16x21mm t=2mm Bracket for Transistor P/N:TRK-2 FB1,FB2 TH1 TH2 L9,10 L12 L8 L1 P1 T2,TER6 TER5,7 J7 J4,9 RLY1 for Q13,17 for Q11,15 for Q11,13,15,17,TH1 2 1 1 2 1 1 1 1 1 2 2 1 2 1 2 2 5 GR SMD DIODE PN:LL4148GSO8 (Vishay)() SMD Transistor (PNP) PN:MMBT5401 LT1 SOT-23 (Q1) SMD Transistor (NPN) PN:MMBT5551 LT1 (ON)(Q2) MOSFET N CHANNEL PN:FB23N20D Bridge Rectifier PN:RS804 400V,8A (BR1) IC:DIP,Regulator PN:LM2574 HVN-15V 8PIN (NS)(U6) D4-5,13,14,21,22,31,33,38,41,45,48,34,6,90,91, Q1 Q2 Q11,13,15,17 BR1 U6 16 1 1 4 1 1
16
L8400P L series
Part Number Drive board Semiconductors 054-000100-100 054-001002-100 054-005501-100 054-007200-100L 054-033906-100 054-050601-100 054-414803-100ZR 054-540100-100 054-555100-100 051-000600-100 051-222200-100 051-555100-000 053-211100-000 Miscellaneous 072-040229-000 072-040230-000 Pre-amp. Board Resistors 024-000097-120 024-100498-121 024-100598-101 024-100598-121 024-100698-101 024-150597-120ZS 024-200598-121 024-220298-121 024-226598-100 024-237597-100 024-270498-121 024-300398-121 024-300598-121 024-330498-101 024-330498-121 024-470598-120 024-470698-121 024-470798-120 024-470798-121 024-510398-121 024-560598-121 024-620398-121 024-680498-121 024-680598-121 024-820598-121 021-330498-100 021-820598-100 026-500495-252 026-500595-267 Capacitors 031-100244-101A 031-100344-102A 031-100344-104A 031-220344-106A 031-330445-100A SMD cap. 0u01/50V K 1206 X7R SMD cap. 0u1/50V K 1206 X7R SMD cap. 100pF/50V K NPO 1206 SMD cap. 220pF/50V K X7R 1206 SMD cap. 3300pF/50V M 1206 X7R C12,13,224,280 C227,229,220,232-235 C222,204 C215,216,200,210 C281 4 7 2 4 1 GS SMD resistor PN:1206J000 0R 1/4W J 1206 SMD resistor 1K 1/4W J 1206 SMD resistor PN:1206F103 10K 1/4W F 1206 R302,303,297 R238,264 R200B,201B,218B,219B R202,206,207,212,222,229,235,252-254,257, SMD resistor 10K 1/4W J 1206 262,282,228,217,205,251 SMD resistor 100K 1/8W F 1206 R200,201,218,219 GS SMD resistor 15K 1/4W J 1206 (R223) R223 SMD resistor 20K 1/4W J 1206 (R256,298) R256,298 SMD resistor 22R 1/4W J 1206 (R249) R249 SMD resistor 22K6 1/4W F 1206 R208,209,231,232 SMD resistor 23K7 1/4W F 1206 (R281) R281 SMD resistor 2K7 1/4W J 1206 (R237) R237 SMD resistor 300R 1/4W J 1206 (R258) R258 SMD resistor 30K 1/4W J 1206 (R260) R260 SMD resistor 3K3 1/4W F 1206 (R203,215) R203,215 SMD resistor 3K3 1/4W J 1206 (R240,210) R240,210 GS SMD resistor 47K 1/8W J 0805 (R280,283) R280,283 SMD resistor 470K 1/4W J 1206 (R259) R259 SMD resistor 4M7 1/8W J 0805 (R244) R244 SMD resistor 4M7 1/4W J 1206 (R243) R243 SMD resistor 510R 1/4W J 1206 (R261) R261 SMD resistor 56K 1/4W J 1206 (R224) R224 SMD resistor 620R 1/4W J 1206 (R221,226) R221,226 SMD resistor 6K8 1/4W J 1206 (R247) R247 SMD resistor 68K 1/4W J 1206 (R250) R250 SMD resistor 82K 1/4W J 1206 (R263) R263 MF resistor 3K3 1/8W F (R204) R204 MOF ressitor 82K 1/8W F (R214) R214 GS VR 5KA PN:RK163111R52B-5KA (EJ) LEVEL R216 GS VR 50KBx4 PN:RD1631411001D-50KBx4 (EJ) XOVER R233 3 2 4 17 4 1 2 1 4 1 1 1 1 2 2 2 1 1 1 1 1 2 1 1 1 1 1 1 1 HEADER Right Angle PN:211-107-000-400 7PIN(PIN2) HEADER Right Angle PN:211-111-000-400 11PIN(PIN1) PIN2 PIN1 1 1 GS SMD DIODE: PN:ES1D 200V 1A (D35,43) SMD ZENER DIODE PN:BZX84C10 10V SOT-23 (D42,49) SMD ZENER DIODE PN:BZV55C3V6 (PHILIPS)(D60) SMD IC: PN:M072M-TE1 DMP8 (JRC) DUAL OP-AMP SMD transistor PN:MMBT3906LT1 SOT23 (ON(Q34,35) SMD ZENER DIODE PN:BZX84C5V6 5.6V SOT-23 TAPIN GR SMD DIODE PN:LL4148GSO8 (Vishay) SMD transistor (PNP) PN:MMBT5401 LT1 SOT-23 SMD transistor (NPN) PN:MMBT5551 LT1 (ON)(Q32) Transistor NPN PN:MPSW06RLRA TO-92 (ON)(Q31) Transistor NPN (ON SEM) PN:MPS2222ARLRA TO-92 Transistor NPN 2N5551 IC:DIP, IR2111 8PIN (IR) HALF-BRIDGE DRIVER D35,43 D42,49 D60 U9,10 Q34,35 Z7,8 D36,39,46,52,61 Q33,40 Q32 Q31 Q20,22 Q21,23 U7,8 2 2 1 2 2 2 5 2 1 1 2 2 2 Description Reference Designator Qty
17
L8400P L series
Part Number Pre-amp. Board 031-470444-101A 031-680444-100A 033-200645-300 034-100515-300G 034-100615-301 034-220516-301 034-220525-300 035-220243-100 035-330293-300 035-330354-301 035-680253-300 035-680353-300 Semiconductors 054-007200-100L 054-011400-100 054-033904-100 054-414803-100ZR Miscellaneous 072-010058-000ZR 072-040008-110 072-040169-000 072-060219-000 074-030002-000 077-100104-100 Fuse PCB 093-205205-300 073-050001-000 039-220384-100 043-324300-000 072-040064-000 072-040096-000 FUSE:VBS UTE FUSE:5A,250V,5*20mm FUSE CLIP P/N:CFFH1206 ( F1,B1) GR X2 Safety Capacitor 0u22/250V x16.5x8.5 INDUCTOR 324uH YT-10778 ( L13) Terminal (PCB TYPE) PC250(t=0.8),T250MA (TER2) Terminal T187MA(PCB TYPE) (t=0.8mm) PC187(0.8) F1 F1,B1 CXAC1 L13 TER2 TER1,3,4 1 2 1 1 1 3 GR RCA JACK 2P PN:0502000W1G (Red,White)(J201) 8P Terminal base JS-1001-08 (P2) CONNECTOR 2 PIN JS-1001-2 P:2.5mm BINDING POST (gold plated) PN:A807A-RB 8PIN TOGGLE SW PN:L101-T2B4QE LFE/PHASE GR conjunction base PN:JS-1001-04 P=2.5 4P J201 P2 CONN4-Pin3,4 J200 SW201,202 CONN5,CONN5B 1 1 1 1 2 2 SMD IC: PN:M072M-TE1 DMP8 (JRC) DUAL OP-AMP SMD Transistor PN:DTC114TKA SMT3 ) SMD Transistor PN:MMBT3904LT1 SOT23 GR SMD DIODE PN:LL4148GSO8 (Vishay) U200-205 Q202 Q203,204 D200-205,207,209,212,216,217,218 6 1 2 12 SMD cap. 4700pF/50V K X7R 1206 SMD cap. 6800pF/50V K X7R 1206 GR NP cap. 200u/50V M (R)1321 P:5 electrolytic cap. 10uF/16V M (R)0511 P:2 Electrolytic cap. 100uF/16V M (R)0611 P:5 Electrolytic cap. 22uF/16V M (R)0511 P:2 GR Electrolytic cap. 22uF/25V M (R)5x11 P:2.5 TAPIN PE cap. FE-M 0u022/63V J P:5m/m PE cap. PN:ESK063S33JT 0u033/63V J P:5 PE cap. FE-M 0u33/63V K P:5m/m PE cap. FE-M PN:ESK063S68JT 0u068/63V J P:5mm GS ESK cap. 0u68/63V J P:5 PN:ESK063P68JA(C214) C2G1 C212 C300,301 C220 C221 C223,225 C14,15 C202 C209,218 C207,208 C201,213 C214 1 1 2 1 1 2 2 1 2 2 2 1 Description Reference Designator Qty
Miscellaneous/Mechanical parts 042-010139-000 063-252623-900 073-014084-500 074-020018-000 086-021836-000 062-252506-000 Power Transformer PN:YT-13438 CSW-10 120V/60Hz Front Panel (L8400P 120V) 10"x10"x0.0984" SPCC black Bracket 6.64"x3.5"x3.2" SPCC ROCKER SW (POWER) PN:RF1003-BB4-0 Power Cord SPT-2 #18 12 ft. +T187 Bucket 10"x10"x4.89" HIPS UL94 V0 PT1 1 1 1 1 1 1
SW4 CORD 01 Plastic air-tight cover
18
L8400P L series
19
L8400P L series
00 01
20
L8400P L series
00 01
21
L8400P L series
00 01
22
L8400P L series
00 01
23