Text preview for : Jbl-PSWD115 actsub.pdf part of JBL PSWD115 active subwoofer
Back to : Jbl-PSWD115 actsub.part1. | Home
PSW D115
Powered Subwoofer
SERVICE MANUAL
JBL Consumer Products Inc. 250 Crossways Park Dr. Woodbury, N.Y. 11797 Rev F 8/2004
Amplifier/Subwoofer
PSW-D115
SAFETY INFORMATION
2
Amplifier/Subwoofer
PSW-D115
TABLE OF CONTENTS
SAFETY INFORMATION ......................................2 TABLE OF CONTENTS ........................................3 GENERAL SPECIFICATIONS ..............................3 PSW-D115 DETAILED SPECIFICATIONS ..........4 PSW-D115 CONTROLS.................................6 OPERATION..........................................................7 SPEAKER CONNECTIONS..................................8 TROUBLESHOOTING ........................................10 SERVICE BULLETIN JBL9903 .......................11 SERVICE BULLETIN JBL2001-02 ..................12 TECH TIP JBLTT2004-02....................................13 PSW-D115 TEST SET UP AND PROCEDURE..14
PSW-D115 POWER AMP MODULE TESTING FLOW CHART ................................15 CABINET EXPLODED VIEWS ........................16 AMPLIFIER EXPLODED VIEW .......................17 PSW-D115 MECHANICAL PARTS LIST..........18 PACKING EXPLODED VIEWS ........................19 PSW-D115 Version 3.21 PCB (Component Side).20 PSW-D115 Version 3.21 PCB (Solder Side).....21 PSW-D115 ELECTRICAL PARTS LIST ...........22 PSW-D115 INTEGRATED CIRCUITS..............24 PSW-D115 SCHEMATIC 1 of 3 .......................25 PSW-D115 SCHEMATIC 2 of 3 .......................26 PSW-D115 SCHEMATIC 3 of 3 .......................27
NOTE: CERTAIN DRAWINGS AND CONNECTIONS WERE DEPICTED INCORRECTLY IN SOME EARLY COPIES OF THE PSW-D112/115 OWNER'S MANUALS. THEY INCLUDE: 1. DRAWING OF RCA LINE LEVEL INPUT/OUTPUT JACKS ON PAGES 3, 4, & 5; ALL CHANNELS - RIGHT SIDE SHOULD BE MARKED "LINE OUT", LEFT SIDE SHOULD BE MARKED "LINE IN". 2. CONNECTION ON PAGE 4 OF OWNER'S MANUAL INVOLVING SINGLE CABLE DIRECT INPUT (FOR DOLBY DIGITAL OR DTS SURROUND); SINGLE CABLE FROM YOUR RECEIVER/PROCESSOR SHOULD CONNECT TO THE "CENTER CHANNEL LINE IN" JACK ON YOUR SUBWOOFER. THOSE DRAWINGS ARE CORRECT IN THIS DOCUMENT, SEE PAGES 8 & 9.
GENERAL SPECIFICATIONS
Amplifier Power (RMS)............................350watts Driver 15".................................................High-Polymer Laminate Inputs ......................................................Line Level and Speaker Level Outputs ...................................................Line Level and Speaker Level Low-Pass Frequency ..............................Continuously variable from 60Hz 180Hz High-Pass Frequency..............................Continuously variable from 60Hz 180Hz when using line-level inputs 150Hz when using speaker-level inputs Frequency Response..............................25Hz low-pass crossover setting Dimensions (H x W x D) .........................20 x 20 x 21 3/4" (508 x 508 x 552mm) Weight ....................................................53lbs/24.1 kg
JBL continually strives to update and improve existing products, as well as create new ones. The specifications and details in this and related JBL publications are therefore subject to change without notice.
3
Amplifier/Subwoofer
PSW-D115
PSW-D115 DETAILED SPECIFICATIONS
4
Amplifier/Subwoofer
PSW-D115
PSW-D115 DETAILED SPECIFICATIONS (Cont.)
5
Amplifier/Subwoofer
PSW-D115
PSW-D115 CONTROLS
6
Amplifier/Subwoofer
PSW-D115
OPERATION
7
Amplifier/Subwoofer
PSW-D115
SPEAKER CONNECTIONS
8
Amplifier/Subwoofer
PSW-D115
SPEAKER CONNECTIONS (Cont.)
9
Amplifier/Subwoofer
PSW-D115
TROUBLESHOOTING
10
Amplifier/Subwoofer
PSW-D115
SERVICE BULETIN JBL9903 - APRIL 1999
11
12
TECH TIPS
Troubleshooting tips and solutions to common service problems
For models: PSWD112 Rev1 only * PSWD115 TIP# JBLTT2004-02
Subject: PSWD112/115 WIRING TO REMOTE VOLUME/CONTOUR/LED CONTROL PLATE A total of 9 wires travel from two Molex connectors on amplifier PCB to 334344-001 Control plate. That control panel is attached by two screws on the inside of the cabinet; the woofer must be removed. The wire cluster is glued into the cabinet opening at the rear of the control panel. The hot melt glue has to be cut out and pried out, then the wire cluster should be re-glued after the control panel is serviced, for air integrity. 1) Two Black sheathed cables, each containing wire colors: Black or Blue White Red 2) Three separate wires: Red White Gray At the Control Plate: Volume pot: Black or Blue, White, Red Contour Switch: Black or Blue, White, Red Power LED: Gray, Red Contour LED: White, Black w/ 10k resistor
* Rev1 version of the PSW-D112 subwoofer is easily identified by the absence of Center channel Input and Output connectors, and is missing the"Direct Out" RCA connector.
13
Amplifier/Subwoofer
PSW-D115
PSW-D115 TEST SET UP PROCEDURE
14
Amplifier/Subwoofer
PSW-D115
PSW-D115 POWER AMP MODULE TESTING FLOW CHART
15
Amplifier/Subwoofer
PSW-D115
CABINET EXPLODED VIEWS
16
Amplifier/Subwoofer
AMPLIFIER EXPLODED VIEW
PSW-D115
16
17
Amplifier/Subwoofer
PSW-D115
PSW-D115 MECHANICAL PARTS LIST
18
Amplifier/Subwoofer
PSW-D115
PACKING EXPLODED VIEW
19
Amplifier/Subwoofer
PSW-D115 Version 3.21 PCB (Component Side)
PSW-D115
19
20
Amplifier/Subwoofer
PSW-D115 Version 3.21 PCB (Solder Side)
PSW-D115
20
21
Amplifier/Subwoofer
PSW-D115
PSW-D115 ELECTRICAL PARTS LIST
22
Amplifier/Subwoofer
PSW-D115
PSW-D115 ELECTRICAL PARTS LIST (Cont.)
23
Amplifier/Subwoofer
PSW-D115
PSW-D115 INTEGRATED CIRCUITS
24
Amplifier/Subwoofer
PSW-D115 SCHEMATIC 1 OF 3
PSW-D115
24
25
Amplifier/Subwoofer
PSW-D115
PSW-D115 SCHEMATIC 2 OF 3
26
Amplifier/Subwoofer
PSW-D115 SCHEMATIC 3 OF 3
PSW-D115
26
27