Text preview for : Jbl-VenueSUB 10actsub.pdf part of JBL VenueSUB10a active subwoofer
Back to : Jbl-VenueSUB 10actsub.pdf | Home
VenueTM Series
SUB10
Amplifier/Subwoofer
SERVICE MANUAL
JBL Consumer Products 250 Crossways Park Dr. Woodbury, New York 11797 Rev2 8/2006
SUB10
Venture Series
- CONTENTS -
BASIC SPECIFICATIONS...................................................1 PACKAGING...................................................................2 DETAILED SPECIFICATIONS .........................................3 CONNECTIONS..............................................................5 OPERATION ................................................................7 TEST SET-UP AND PROCEDURE......................................8 EXPLODED VIEW/PARTS LIST.........................................9 BLOCK DIAGRAM...........................................................10 120V ELECTRICAL PARTS LIST .....................................11 PCB DRAWINGS...........................................................15 INTEGRATED CIRCUIT/TRANSISTOR PINOUTS..............21 120V SCHEMATICS............................................. .........22
BASIC SPECIFICATIONS SUB10 Subwoofer
Frequency response: Amplifier Power output: Amplifier Peak Dynamic Power: Crossover Frequencies Woofer: Dimensions (including grille): Weight: 27Hz 150Hz 150W Continuous RMS power 250W 50Hz 150Hz, 24dB/octave, continuously variable 10" (250mm) PolyPlasTM cone 17-3/4" x 12-1/4" x 15-3/4" (451mmx311mmx400mm) 32.1 lb/14.6kg
The Peak Dynamic Power is measured by recording the highest center-to-peak voltage measured across the output of a resistive load equal to minimum impedance of the transducer, using a 50Hz sine wave burst, 3 cycles on, 17 cycles off. Occasional refinements may be made to existing products without notice but will always meet or exceed original specifications unless otherwise stated
1
SUB10
Venture Series
2
SUB10
JBL Venue Sub10 150W Powered Sub/ Plate Amp
LINE VOLTAGE US 120vac/60Hz EU 230vac/50-60Hz Asia 100vac/50Hz Yes/No Yes Yes Yes Hi/Lo Line 108-132 207-264 90-110 Unit Vrms Vrms Vrms Notes Normal Operation Normal operation, MOMS required Normal Operation
Venture Series
Parameter Amp Section Type (Class AB, D, other) Load Impedance (speaker) Rated Output Power THD@ Rated Power THD @ 1 Watt DC Offset Damping factor Input Sensitivity Input Frequency Line Input (L&R) LFE Input Speaker/Hi Level Input Signal to Noise SNR-A-Weighted SNR-unweighted SNR @ 1W-unweighted Residual Noise Floor Residual Noise Floor Input Impedance Line input L&R , LFE Speaker/Hi Level Input Filters Left & Right inputs LP Slope & Q LFE Low Pass fixed Slope & Q Subsonic filter (HPF) Slope & Q Limiter (yes/no) Features LFE Input Phase Switch (yes/no) Volume pot Taper (lin/log) ATO switch (AUTO/ON) Input Configuration Line In (L,R) Line level in LFE Spkr/Hi Level In (L,R) Spkr Out: Level out (L,R) Signal Sensing (ATO) ATO test Frequency ATO Line Level ATO Speaker level input ATO Turn-on time Auto Mute/ Turn-OFF Time
Specification D 4 150 0.08 0.1 10 >100 50 13 8 110 100 90 60 1 1 >15 4.7
Unit D Ohms Watts % % mV-DC N/A Hz mVrms mVrms mVrms dBA dBr dBr mVrms
QA Test Limits n/a n/a 145 1.5 0.5 20 15 50 ±2dB ±2dB ±2dB 85 80 55 2 2 n/a n/a ±2dB n/a ±2dB n/a ±2dB n/a n/a functional functional functional functional functional functional functional functional
Conditions Nominal 1 input driven 22K filter 22K filter @ Speaker Output 50Hz, 4 Ohms load Nominal Freq. To 1 W To 1 W To 1 W rel. to rated power rel. to rated power rel. to 1W Output Volume @max, using RMS reading DMM/VOM (or A/P) Volume @max, w/ A/P Swept Bandpass Measurement (Line freq.+ harmonics) Nominal Nominal 2nd order fix and 2nd order variable
Notes
Measured at amplifier board speaker output terminals @ 135 Watts 1 input driven, AP Zo=600 Ohms 1 input driven, AP Zo=600 Ohms LFE input driven only, AP Zo=600 Ohms (Approx -20 dB below Line In)...1 input driven A-Weighting filter 22K filter 22K filter
mVrms(max)
K ohms K ohms
Hz -4th dB/Octave Hz -2nd dB/Octave Hz -5th dB/Octave YES YES YES LOG YES L ,R LFE L,R L,R --
---
BW Limited to 500 Hz
---
RCA inputs: L and R L & R inputs, binding post connectors Only applies to 230V model
50 2 25 5 15
Hz mV mV ms minutes functional functional functional functional 2mV@50Hz into Line Input w/ 1 ch. driven 50mV@50Hz into Line Input w/ 1 ch. driven Amp connected and AC on, then input signal applied T before muting, after signal is removed Auto turn of time (T) must be 10 > T <15
3
SUB10
Parameter Power on Delay time Transients/Pops ATO Transient Turn-on Transient Turn-off Transient Efficiency 16 240 functional functional functional @ nom. line voltage @ nom. line voltage Direct short at output @1/8 max unclipped Power DC present at Speaker Out leads Specification 3 5 50 50 Unit sec. mV-peak mV-peak mV-peak QA Test Limits functional 10 100 100 Conditions AC Power Applied @ Speaker Outputs @ Speaker Outputs @ Speaker Outputs Notes
Venture Series
AC Line cycled from OFF to ON AC Line cycled from ON to OFF Maximum allowable input power under nominal Input voltage and frequency, HOT or COLD operation. 140 Watts @ 4 Ohms nominal line voltage
Stand-by Input Power Power Cons.@rated power Protection Short Circuit Protection Thermal Protection DC Offset Protection Line Fuse Rating US Version EU Version
14 230 YES 65 deg. C YES 3.15 1.6
Watts Watts ---Amps Amps
Temperature rise should not exceed 35K rise Relay or crowbar (for driver/fire protection)
Type-T or Slo Blo, T3.15A, 250V External fuse with UL/SEMKO rated holder Type-T, Low breaking capacity, T1.6AL, 250V External fuse with UL/SEMKO rated holder
4
SUB10 SYSTEM CONNECTIONS
If you have a Dolby® Digital or DTS® receiver/processor with a low-frequencyeffects (LFE) or subwoofer output:
Venture Series
If your receiver/processor does not have subwoofer outputs for the left and right channels or an LFE output, connect speaker wire from your receiver/ amplifier to your speakers and subwoofer using two sets of speaker wire:
SUBWOOFER OR LFE OUTPUT
RECEIVER/AMPLIFIER Front Speaker Output
IN
ANDBY
L
R
0
0
IN
L
R
If your receiver/processor does not contain a Dolby Digital or DTS processor but has subwoofer outputs: NOTE: If your receiver/processor has only one sub out, you may use either the L or R input.
RECEIVER/PROCESSOR
L
R
IN
L
R
L
0
This figure shows how to connect bare wires to the speaker-level terminals.
5
SUB10
Venture Series
SPEAKER LEVEL
IN
LINE LEVEL IN
1 0
L R
3
SUBWOOFER LEVEL
4
GREEN: ON RED: STAND-BY
LFE
CROSSOVER PHASE
L
2
R MIN
AUTO ON
0
0
180
0
7
50 Hz 150
MAX
5
6
"WAR NING : FOR CONTINUED PROTECTION AGAINST RISK OF FIRE, REPLACE ONLY WITH SAME TYPE T 3.15A L/250V FUSE" "AVE R TIS S E ME NT: UTILISEZ UN FUSIBLE DE RECHANGE DE MEME TYPE T 3.15A L/250V"
T3.15A L/250V
TM
®
SUB10
®
POWER
8
R
RISK OF ELECTRIC SHOCK DO NOT OPEN
C A UT IO N
NRTL/C CSA 22-2 No.1 UL 1492
AC 120V~60Hz 250 Watts
¡ Speaker-Level Inputs TM LFE Input £ Line Inputs ¢ Subwoofer-Level Control Power Indicator LED
§ On/Off Auto Switch ¶ Phase Switch · Crossover Adjustment ª Power Switch
6
SUB10 OPERATION
Power On Plug your subwoofer's AC cord into a wall outlet. Do not use the outlets on the back of the receiver. Initially set the Subwoofer-Level Control ¢ to the "min" position. Turn on your sub by pressing the Power Switch ª on the rear panel. Turn on your entire audio system and start a CD or movie soundtrack at a moderate level. Auto On/Standby With the Power Switch ª in the "on" position, the Power Indicator LED will remain backlit in red or green to indicate the On/Standby mode of the subwoofer. RED = STANDBY (No signal detected, Amp Off) GREEN = ON (Signal detected, Amp On) When the Auto Switch § is in the "auto" position, the subwoofer will automatically enter the Standby mode after approximately 10 minutes when no signal is detected from your system. The subwoofer will then power ON instantly when a signal is detected. During periods of normal use, the Power Switch ª may be left on. You may turn off the Power Switch ª for extended periods of non-operation, e.g., when you are away on vacation. If the Auto Switch § is in the "on" position, the subwoofer will remain on. Adjust Gain Turn your Subwoofer-Level Control ¢ up to the halfway position. If no sound emanates from the subwoofer, check the AC-line cord and input cables. Are the connectors on the cables making proper contact? Is the AC plug connected to a "live" receptacle? Has the Power Switch ª been pressed to the "on" position? Once you have confirmed that the subwoofer is active, proceed by playing a CD, record or cassette. Use a selection that has ample bass information. Set the overall volume control of the preamplifier or stereo to a comfortable level. Adjust the Subwoofer-Level Control ¢ until you obtain a pleasing blend of bass. Bass response should not overpower the room but rather be adjusted so there is a harmonious blend across the entire musical range. Many users have a tendency to set the subwoofer volume too loud, adhering to the belief that a subwoofer is there to produce lots of bass. This is not entirely true. A subwoofer is there to enhance bass, extending the response of the entire system so the bass can be felt as well as heard. However, overall balance must be maintained or the music will not sound natural. An experienced listener will set the volume of the subwoofer so its impact on bass response is always there but never obtrusive. Phase Control The Phase Switch ¶ determines whether the subwoofer speaker's pistonlike action moves in and out with the main speakers, 0°, or opposite the main speakers, 180°. Proper phase adjustment depends on several variables such as room size, subwoofer placement and listener position. Adjust the Phase Switch to ¶ maximize bass output at the listening position. Crossover Adjustment The Crossover Adjustment Control · determines the highest frequency at which the subwoofer reproduces sounds. If your main speakers can comfortably reproduce some low-frequency sounds, set this control to a lower frequency setting, between 50Hz and 100Hz. This will concentrate the subwoofer's efforts on the ultradeep bass sounds required by today's films and music. If you are using smaller bookshelf speakers that do not extend to the lower bass frequencies, set the Crossover Adjustment Control · to a higher setting, between 120Hz and 150Hz. NOTE: This control will have no effect if the LFE/Input TM is used. If you have a Dolby Digital or DTS processor/receiver, the low-pass frequency is set by the processor/receiver. Consult your owner's manual to learn how to view or change this setting.
Venture Series
The enclosure may be cleaned using a soft cloth to remove fingerprints or to wipe off dust. The grille may be gently vacuumed. Stains may be removed with an aerosol cleaner, following its instructions. Do not use any solvents on the grille.
6 7
SUB10
Venture Series
SUB10 Test Set Up and Procedure
Equipment needed: · Function/signal generator/sweep generator · Integrated Amplifier · Multimeter · Speaker cables General Unit Function (UUT = Unit Under Test) 1) From the signal generator, connect line level (RCA) cables to the Subwoofer Line Level Input jacks L/R on the UUT. Use a Y-cable from a mono source if necessary to connect to both inputs. Do not connect to the single LFE input. 2) Turn the CROSSOVER control to maximum (150). 3) Turn the LEVEL control on the UUT to completely counterclockwise (MIN). 4) Turn on generator; adjust to 100mV, 50 Hz. 5) Plug in UUT; turn the power switch ON. LED should switch from Red to Green. 6) Turn LEVEL control full clockwise (MAX); immediate and vigorous bass response should be heard and felt from port tube opening on the bottom. 7) Turn off generator, turn LEVEL control full counterclockwise (MIN), and disconnect RCA cable. 8) Connect one pair of speaker cables to Speaker Level input terminal (IN) on UUT. Cables should be connected to an integrated amplifier fed by the signal generator. 9) Turn on generator and adjust so that speaker level input at the amplifier is 2.0V, 50 Hz. Turn LEVEL control full clockwise (MAX). 10) Green LED should light; immediate and vigorous bass response should be heard and felt from the port tube opening. Sweep Function 1) Follow steps 8-10 above, using a sweep generator as a signal source. 2) Sweep generator from 20Hz to 300Hz. Listen to the cabinet and drivers for any rattles, clicks, buzzes or any other noises. If any unusual noises are heard, remove woofers and test. Driver Function 1) Remove woofer from cabinet (instructions on exploded view drawing); detach + and - wire clips. 2) Check DC resistance of woofer; it should be 5.7 ohms ±10% 3) Connect a pair of speaker cables to driver terminals. Cables should be connected to an integrated amplifier fed by a signal generator. Turn on generator and adjust so that speaker level output is 5.0V. 4) Sweep generator from 20Hz to 1kHz. Listen to driver for any rubbing, buzzing, or other unusual noises.
8
SUB10
Venture Series
9
SUB10
Venture Series
10
SUB10 SUB10 120V Electrical parts list
Part number PREAMP PCB Resistors 110-12472j52-e 110-16102j26-e 110-16103j26-e 110-16104j26-e 110-16105j26-e 110-16122j26-e 110-16151j26-e 110-16154j26-e 110-16183j26-e 110-16205j26-e 110-16223j26-e 110-16333j26-e 110-16472j26-e 110-16473j26-e 110-16512j26-e 110-16913j26-e 116-161002f26-e 116-161132f26-e 116-161301f26-e 116-161372f26-e 116-161542f26-e 116-162433f26-e 116-165601f26-e 116-166042f26-e 116-169091f26-e 115-h203b201-e 115-h503a101-e Capacitors 129-a153j633-e 129-a224j633-e 129-a334j633-e 130-2b221k503-e 130-3f104z503-e 130-sl101k503-e 132-103j503-e 132-104ja03-e 132-473ja03-e 135-3105m50-e 135-3106m50-e 135-3107m16-e 135-3226m50-e 135-3227m16-e 129-a334j633-e Semiconductors 192-027c1815gr-e Transistor 2SC1815GR TOSHIBA(RoHS) NPN 197-031n4148-e 199-15000335-e 190-06m4558d-e 190-16tl074cn-e 192-027c1815gr-e diode 100mA 75V SIGNAL 1N4148 zener diode 3.3V 1/2W 52mm TA I.C. OPA 4558D (RoHS) DUAL OP-AMP *I.C TL074CN ST (RoHS) QUAD OP-AMP Transistor 2SC1815GR TOSHIBA(RoHS) NPN Metallize Capacitor 0.015U 63V MSC Metallize Capacitor 0.22uF 63V ±5% MSC Metallize Capacitor 0.33uF 63V ±5% MSC Disc Capacitor 220P 50V ±10% Disc Capacitor 0.1U 50V +80/-20% Disc Capacitor 100P 50V SL ±10% mylar Capacitor 0.01uF 50V ±5% mylar Capacitor 0.1UF 100V ±5% mylar Capacitor 0.047uF 100V ±5% electrolytic 1U 50V ±20% electrolytic10uF 50V ±20% electrolytic 100uF 16V ±20% electrolytic 22U 50V ±20% electrolytic 220U 16V ±20% metalize cap 0.33uF 63V ±5% MSC Resistor4.7K 1/2W ±5% CF 52mm (RoHS) Resistor 1K 1/6W ±5% CF 26mm (RoHS) Resistor10K 1/6W ±5% CF 26mm (RoHS) Description Qty Reference Designator
Venture Series
Resistor100K 1/6W ±5% CF 26mm (RoHS) Resistor1M 1/6W ±5% CF 26mm (RoHS) Resistor 1.2K 1/6W ±5% CF 26mm (RoHS) Resistor 150 1/6W ±5% CF 26mm (RoHS) Resistor150K 1/6W ±5% CF 26mm (RoHS) Resistor18K 1/6W ±5% CF 26mm (RoHS) Resistor 2M 1/6W ±5% CF 26mm (RoHS) Resistor22K 1/6W ±5% CF 26mm (RoHS) Resistor 33K 1/6W ±5% CF 26mm(RoHS) Resistor 4.7K 1/6W ±5% CF 26mm (RoHS) Resistor47K 1/6W ±5% CF 26mm (RoHS) Resistor 5.1K 1/6W ±5% CF 26mm (RoHS) Resistor 91K 1/6W ±5% CF 26mm (RoHS) Metal Film Resistor 10K 1/6W ±1% MF 26mm (RoHS)
Metal Film Resistor11.3K 1/6W ±1% MF 26mm (RoHS)
Metal Film Resistor1.30K 1/6W MF 26mm (RoHS)
Metal Film Resistor 13.7K 1/6W MF 26mm (RoHS) Metal Film Resistor 1/6W 15.4K 1% 26mm (RoHS)
Metal Film Resistor 243K 1/6W 1% MF 26mm (RoHS) Metal Film Resistor 5.60K 1/6W ±1% MF26mm (RoHS)
Metal Film Resistor 60.4K 1/6W±1% MF Metal Film Resistor 9.09K 1/6W±1% MF variable Resistor 20KB/2 CROSSOVER variable Resistor D16 50K/1 A (RoHS) LEVEL
R201,R202 R213,R214,R215,R254 R209,R212,R216,R217,R220,R221,R222,R228, 15 R218,R230,R232,R240,R248,R260,R235 4 R231,R263,R266,R251 1 R259 1 R265 1 R253 1 R252 R261 1 1 R257 3 R247,R255,R256 1 R249 3 R208,R207,R258 3 R219,R250,R264 2 R210,R211 4 R203,R204,R205,R206 3 R10,R11,R9 2 R225,R7 1 R3 2 R226,R227 R238,R237 2 R6 1 2 R223,R224 1 R233 1 R234 1 VR202, 1 VR201 2 4
C224 C221,C222,C218 C1,C3 C200,C204,C205,C207,C213,C210,C211,C212, 12 C214,C220,C230,C249, 9 C232,C242,C244,C245, C246,C252,C254,C255,C256 C6 1 1 C223 1 C216 2 C215,C217 1 C228 10 C201,C202,C206,C208, C231,C241,C243,C251,C253,C219 1 C234 2 C225,C7 1 C233, 1 C2, 1 3 2
Q201,Q207,Q208, D201,D202,D203,D204, D205,D206,D207,D208, 13 D211,D212,D214,D215,D216 D213, 1 U1,U203, 2 U201,U202, 2 Q206, 1 3
11
SUB10
Part number PREAMP PCB 195-10204hgw-e Miscellaneous 162-50062001-e 174-0rca326p-e 174-2wp810a-e 175-1c07v01-e 180-tsv6201-e MAIN PCB Resistors 110-20332jk3-e 113-50s68j00-e 116-201001jk3x-e 116-304700jk2x-e 110-14103j26-e 110-14222j26-e 110-14432j26-e 110-14472j26-e 110-16102j26-e 110-16103j26-e 110-16104j26-e 110-16153j26-e 110-16182j26-e 110-16203j26-e 110-16221j26-e 110-16222j26-e 110-16223j26-e 110-16333j26-e 110-16393j26-e 110-16434j26-e 110-16473j26-e 110-16474j26-e 110-16562j26-e 110-16621j26-e 110-16751j26-e 110-16755j26-e 116-161002f26-e 116-161202f26-e 116-162200f26-e 116-162202f26-e Capacitors 138-5478m80-e 132-a103ja03-e 132-103kd00-e 130-3f104z503-e 130-sl101k503-e 132-103j503-e 132-104ja03-e 132-273ja03-e 135-3106m50-e 135-3107m10-e 135-3107m35-e 135-3225m50-e 135-3226m16-e large aluminum ec 4700uF 80V ±20% 85 (RoHS) Mylar Capacitor 0.01u 100V (RoHS) mylar Capacitor 0.01U 400V +/-10% long foot (RoHS) base capacity 0.1U 50V +80/-20% base Capacitor 100P 50V SL ±10% mylar Capacitor0.01uF 50V ±5% mylar Capacitor 0.1UF 100V ±5% mylar Capacitor0.027UF 100V ±5% electrolytic Capacitor 10uF 50V ±20% electrolytic cap 100U 10V ±20% electrolytic cap100U 35V ±20% electrolytic cap 2.2U 50V ±20% electrolytic cap 22U 16V ±20%
2 2 1 6 3 2 3 1 2 2 2 1 1
Venture Series
Description Qty Reference Designator
double color LED 204HGW 3 (RoHS)
1
D209,
2PIN 60mm red/black JACK RCA-326 (RoHS)
SPK JACK 8P red up black down with cap
wire connector &base7PIN PITCH=2.5mm (RoHS) switch 6PIN DC30V 0.3V AUTO-ON, PHASE
1 1 1 1 2
for D209, JK201, JK203, P201, SW1,SW201
Resistor 3.3K 2W ±5% portrait short foot7.5m(RoHS) Resistor 0.068 5W ±5% landscape short foot(RoHS) Metal Film Resistor 1.00K 2W ±5% (RoHS) Metal Film Resistor 470 3W ±5% 10mm (RoHS) Resistor10K 1/4W ±5% CF 26mm Resistor 2.2K 1/4W ±5% CF 26mm TAP (RoHS) Resistor4.3K 1/4W ±5% CF 26mm Resistor 4.7K 1/4W ±5% CF 26mm Resistor 1K 1/6W ±5% CF 26mm Resistor10K 1/6W ±5% CF 26mm Resistor 100K 1/6W ±5% CF 26mm Resistor15K 1/6W ±5% CF 26mm Resistor 1.8K 1/6W ±5% CF 26mm Resistor 20K 1/6W ±5% CF 26mm Resistor220 1/6W ±5% CF 26mm Resistor 2.2K 1/6W ±5% CF 26mm Resistor 22K 1/6W ±5% CF 26mm Resistor33K 1/6W ±5% CF 26mm Resistor 39K 1/6W ±5% CF 26mm Resistor 430K 1/6W ±5% CF 26mm Resistor 47K 1/6W ±5% CF 26mm Resistor 470K 1/6W ±5% CF 26mm Resistor 5.6K 1/6W ±5% CF 26mm Resistor 620 1/6W ±5% CF 26mm Resistor 750 1/6W ±5% CF 26mm Resistor 7.5M 1/6W ±5% CF 26mm metal film Resistor10K 1/6W ±1% MF 26mm metal film Resistor 12.0K 1/6W ±1% MF metal film Resistor 220 1/6W ±1% MF metal film Resistor 22.0K 1/6W ±1% MF
1 1 1 2 3
1 1
1 1 10 3 1 1 1 1 1 1 1 1 1 2 1 1 1 1 1 2 1 1 1
R134 R147 R148 R501,R502 R503,R504,R510, R511, R506, R505, R153, R128,R130,R149,R150,R305,R306,R308,R311,R314,R319, R122,R126,R307, R107, R145, R309, R144, R102, R316, R310, R151, R312, R106,R129, R127, R152, R160, R315, R313, R301,R303, R302, R317, R318,
C501,C502 C103,C104 C500 C107,C117,C122,C144, C320,C322 C302,C303,C306, C305,C317, C123,C503,C504, C143, C319,C321, C114,C115, C507,C508, C509, C304,
12
SUB10
Part number MAIN PCB 135-3226m50-e 135-3227m16-e 135-3476m16-e Semiconductors 190-16tl074cn-e 192-161tip31c-e 192-161tip32c-e 197-00kbu606g-e 197-141n4004-e 192-027c1815gr-e 192-027c2235y-e 192-028a1015gr-e 192-1572n5551-e 192-1582n5401-e 197-031n4148-e 199-15000625-e 199-15001605-e Miscellaneous 120-1000003-e 109-1ttc802j0-e 162-50129001-e 171-urwh124d-e 175-1d02v01-e 175-1d03v01-e
inductor10W AI YT-C3104-005 1CRHW354708LTB (RoHS) Thermister TTC-802(JS) NTC long foot(RoHS)
Venture Series
Description Qty Reference Designator
electrolytic cap 22U 50V ±20% electrolytic cap 220U 16V ±20% electrolytic cap47U 16V ±20%
2 1 1
C505,C506, C118, C318,
*I.C TL074CN ST (RoHS) DUAL OP-AMP Transistor TIP31C SGS (RoHS) NPN TransistorTIP32C SGS (RoHS) PNP diode6A 800V KBU606G (RoHS) BRIDGE diode1N4004 (RoHS) Transistor 2SC1815GR TOSHIBA(RoHS) NPN Transistor2SC2235Y TOSHIBA (RoHS) NPN Transistor 2SA1015GR TOSHIBA(RoHS) PNP TransistorFSC 2N5551 (RoHS) NPN TransistorFSC 2N5401 TO-92 (RoHS) PNP diode100mA 75V SIGNAL 1N4148 zener diode HZ6C2 RENESAS (6.2v) zener diode HZ16-2 RENESAS (16v)
1 1
1
1 2 5 1 3 2 1 4 1 1
U301 Q501 Q502 D501 D110,D504 Q108,Q109,Q113,Q301, Q302, Q111, Q101,Q107,Q112, Q114,Q115, Q503, D102,D103,D104,D105, D101, D502,
CABLE ASS'Y wire 120mm AWG28 WHT (RoHS) Relay RWH-SH-124D (1600 ohm) (RoHS) Wire connector&base 2PIN PITCH=3.96mm (RoHS) Wire connector&base 3 PIN PITCH=3.96mm (RoHS)
2 1 1 1 1 1
FB1,FB2 TH1 W201 RL1 M100 M500
CLASS D ASS'Y PCB (Replacment of entire module is recommended, part# 051-B00012A-E). Resistors 118-120610r0j-e 118-12061001j-e 118-12061002j-e 118-12061201j-e 118-12062002j-e 118-12062201j-e 118-12062701j-e 118-12063000j-e 118-12063301j-e 118-12063902j-e 118-120647r0j-e 118-12064700j-e 118-12064701j-e 118-12064702j-e 118-12064704j-e Capacitors 128-e106ma01k-e 141-c0220k50-e 141-c0561k50-e 141-c5104m50-e 141-c7223k50-e 141-c0101k50-e 141-d7104ka0-e 141-d7104kb5-e
crossver cap 10UF 100V 20% 105 long foot (RoHS)
SMD Capacitor 22pF 50V 10% 1206 SMT NPO (RoHS)
SMDresistor 10.0 1206 5% (RoHS) SMDresistor 1.00K 1206 5% (RoHS) SMDresistor 10.0K 1206 5% (RoHS) SMDresistor 1.20K 1206 5% (RoHS) SMDresistor 20.0K 1206 5% (RoHS) SMDresistor 2.20K 1206 5% (RoHS) SMDresistor 2.70K 1206 5% (RoHS) SMDresistor 300.0 1206 5% (RoHS) SMDresistor 3.30K 1206 5% (RoHS) SMDresistor 39.0K 1206 5% (RoHS) SMDresistor 47.0 1206 5% (RoHS) SMDresistor 470 1206 5% (RoHS) SMDresistor 4.70K 1206 5% (RoHS) SMDresistor 47.0K 1206 5% (RoHS) SMDresistor 4.70M 1206 5% (RoHS)
R22,R23 R2,R11,R29,R30 R7,R9,R25 R31,R32,R33,R34,R35,R36,R37,R38 16 R39,R40,R41,R42,R43,R44,R45,R46 1 R26 3 R6,R13,R16 1 R10 1 R24 4 R14,R15,R27,R28, 1 R3 2 R20,R21 1 R8, 3 R1,R5,R12, 1 R17 1 R4,
2 4 3
2
1 1 8 1 1 2 4
SMD Capacitor 560pF 50V 10% SMD Capacitor 1206 Y5V 0.1uF 50V ±20% (RoHS) SMD Capacitor 0.022uF 50V 10%1206 X7R (RoHS) SMD Capacitor 100pF 50V 10% 1206 NP0 (RoHS) SMD Capacitor 0.1uF 100V 10% 1210 X7R (RoHS) SMD Capacitor 0.1uF 250V 10% 1210 X7R (RoHS)
C16,C17 C5, C6, C2,C3,C7,C8,C9,C10,C11,C15, C13, C4, C12,C14 C1,C18,C19,C20,
13
SUB10
Part number Description Qty Reference Designator CLASS D ASS'Y PCB (Replacment of entire module is recommended, part# 051-B00012A-E). Semiconductors 190-16tl072dts-e 192-09124126qs-e 192-09139066rs-e 192-09210376qs-e 192-09215146rs-e 197-03rls4148s-e 192-232irf9640-e 192-233f640n-e 199-15000563s-e 199-1500120s-e 199-15001503s-e Miscellaneous 122-14121m4191-e Ferrite core LS-A6206-ST EFD-30 (RoHS) 122-14350j4180-e chock coil35uH Ferrite Core 25 Milliohm (RoHS) 175-9f40hr2-e wire connector & base 40PIN (RoHS) MISCELLANEOUS/MECHANICAL
350-FM04012D106-E 4*12 wood screw(RoHS) 352-AM03010D066-E 3*10 Ptype tapping screw(RoHS) 352-AM03008D041-E 3*8 Btypetapping screw (RoHS)
Venture Series
SMD I.C. TL072CDT SGS THOMSON DUAL OP-AMP
SMD Transistor 2SC2412K-T146Q/R SMD Transistor 2SC3906K-T146R ROHM SMD Transistor 2SA1037K-T146Q/R SMD Transistor2SA1514K-T146R ROHM SMD Transistor RLS4148-TE11 ROHM FET IRF9640 IR P-CH TO220(RoHS) Transistor IRF640N INTERNATIONA(RoHS)
SMD ZENER 5.6V 5% PHILIPS BZX84-C5V6 (RoHS) SMD ZENER 12V 5% PHILIPS BZX84-C12 (RoHS) SMD ZENER 15V 5% PHILIPS BZX84-C15 (RoHS)
1 3 2 2 2 6
1 1
2 2 2
IC1, Q1,Q4,Q5, Q2,Q8, Q7,Q9 Q3,Q6, D1,D2,D3,D4,D5,D6, Q10 Q11 Z1,Z2, Z5,Z6, Z3,Z4
1 L1 1 L2 0.2
150-r4055900-e 152-u602015-e 154-k31505t0-e 155-63032i-e 180-pbr12c11s-e 162-10082007-e
power Xformer I/P:120V/60Hz TT0900008720 (RoHS) line cord polar SVT FT-2 6FT double insulator (RoHS) fuse 3.15A 250V 30mm UL/CSA /PSE (RoHS) fuse holderHTB-32I 30mm UL/CSA (RoHS) power switch PUSH BR12C11S (RoHS) WIRE RED 18AWG 80mm 8mm#1015 (RoHS)
362-FE-00013-0LAE PCB support L TYPE t=1.6mmS.P.C.C 89*9*1.6T (RoHS)
311-ABS-00028-0BAE LEVEL KNOB 46077-W P.V.C.(RoHS) 306-ABS-00004-0BAE rear Plastic housing 268*213*102 A.B.S UL (RoHS)
176-wjce1-e
333-EVA-00096-0BAE 333-EVA-00097-0BAE 333-EVA-00132-0BAE 333-EVA-00133-0BAE 333-EVA-00220-0BAE
333-EVA-00188-0BAE
130-3f104z503-e 193-201815t2-e
352-HM03012D086-E 317-000-00037-0LAE
323-AL-00056-0LAE
333-EVA-00219-0BAE
351-AM03008A078-E
162-a040d005-e
wire connector pinCE-1 (RoHS) EVA gasket wide side213*15*2.0mm(RoHS) EVAgasket wide side213*15*1.0t (RoHS) EVA gasket long side238*15*2.0mm (RoHS) EVAgasket long side238*15*1.0t (RoHS) EVAgasket long side225*15*1t UL(RoHS) EVA gasket 170x5x1t (RoHS) disc capacitor 0.1U 50V +80/-20% TAP(RoHS) insulator (RoHS) 3*12 Btypetapping screw black (RoHS) panel M3 solder t=0.3 (RoHS) heat sink 83.5*50.5*27.5H EVAgasket 150*15*1t UL(RoHS) M3*8 machine screw (RoHS) spkr wire red and black#1015 add #205 250 pin(RoHS)
4 3 4 1 1 1 1 1 1 2 2 1 1 2 2 2 2 1 1 1
T501 F501 for F501 SW501
C110
302-AL-00020-1LCE rear board 270*215*2.5T SUB10 AL (RoHS)
335-NYL-05015-0BAE wire clip SB4F-2 black(RoHS)
1 1 1 6 1 1 2
14
SUB10
Venture Series
15
SUB10
Venture Series
16
SUB10
Venture Series
17
SUB10
Venture Series
18
SUB10
Venture Series
19
SUB10
Venture Series
20
SUB10
Venture Series
, IC1
21
SUB10
Venture Series
22
SUB10
Venture Series
23
SUB10
Venture Series
24
SUB10
Venture Series
25