Text preview for : PIONEER M-IS22.pdf part of PIONEER M-IS22 PIONEER M-IS22 stereo rower amplifier



Back to : PIONEER M-IS22.pdf | Home

POWER AMPLIFIER M-IS22 AERO DUCT CONSTRUCTION

STANDBY/ON

STANDBY

ORDER NO.
PHONES

RRV2445

STEREO POWER AMPLIFIER

M-IS22
THIS MANUAL IS APPLICABLE TO THE FOLLOWING MODEL(S) AND TYPE(S).
Type
MYXJ NVXJ

Model M-IS22
AC220-230V AC230V

Power Requirement

Remarks

This product is a component of a system. For the accessories, instruction manuals etc., refer to the service manuals RRV2442 for XC-IS22CD. This product does not function properly when independent; to avoid malfunctions, be sure to connect it to the prescribed system component(s), otherwise damage may result.
Component CD TUNER DECK STEREO POWER AMPLIFIER SPEAKER SYSTEM System XC-IS22CD M-IS22 S-IS22 ­­­ ­­­ S-IS22S Service Manual RRV2442 RRV2445 RRV2450 RRV2451 Remarks

This Service Manual

CONTENTS
1. SAFETY INFORMATION ...................................... 2 2. EXPLODED VIEWS AND PARTS LIST ................ 3 3. SCHEMATIC DIAGRAM ....................................... 6 4. PCB CONNECTION DIAGRAM .......................... 12 5. PCB PARTS LIST ............................................... 18 6. ADJUSTMENT .................................................... 20 PIONEER CORPORATION 7. GENERAL INFORMATION ................................ 21 7.1 SINGLE OPERATION METHOD ................. 21 8. PANEL FACILITIES AND SPECIFICATIONS .... 22

4-1, Meguro 1-chome, Meguro-ku, Tokyo 153-8654, Japan PIONEER ELECTRONICS SERVICE, INC. P.O. Box 1760, Long Beach, CA 90801-1760, U.S.A. PIONEER EUROPE NV Haven 1087, Keetberglaan 1, 9120 Melsele, Belgium PIONEER ELECTRONICS ASIACENTRE PTE. LTD. 253 Alexandra Road, #04-01, Singapore 159936

PIONEER CORPORATION 2001
T ­ ZZK APR. 2001 Printed in Japan

M-IS22

1. SAFETY INFORMATION
This service manual is intended for qualified service technicians; it is not meant for the casual do-it-yourselfer. Qualified technicians have the necessary test equipment and tools, and have been trained to properly and safely repair complex products such as those covered by this manual. Improperly performed repairs can adversely affect the safety and reliability of the product and may void the warranty. If you are not qualified to perform the repair of this product properly and safely, you should not risk trying to do so and refer the repair to a qualified service technician.
WARNING This product contains lead in solder and certain electrical parts contain chemicals which are known to the state of California to cause cancer, birth defects or other reproductive harm. Health & Safety Code Section 25249.6 ­ Proposition 65

NOTICE (FOR CANADIAN MODEL ONLY) Fuse symbols (fast operating fuse) and/or (slow operating fuse) on PCB indicate that replacement parts must be of identical designation. REMARQUE (POUR MODÈLE CANADIEN SEULEMENT) Les symboles de fusible (fusible de type rapide) et/ou (fusible de type lent) sur CCI indiquent que les pièces de remplacement doivent avoir la même désignation.

(FOR USA MODEL ONLY) 1. SAFETY PRECAUTIONS
The following check should be performed for the continued protection of the customer and service technician.

LEAKAGE CURRENT CHECK
Measure leakage current to a known earth ground (water pipe, conduit, etc.) by connecting a leakage current tester such as Simpson Model 229-2 or equivalent between the earth ground and all exposed metal parts of the appliance (input/output terminals, screwheads, metal overlays, control shaft, etc.). Plug the AC line cord of the appliance directly into a 120V AC 60 Hz outlet and turn the AC power switch on. Any current measured must not exceed 0.5 mA.

ANY MEASUREMENTS NOT WITHIN THE LIMITS OUTLINED ABOVE ARE INDICATIVE OF A POTENTIAL SHOCK HAZARD AND MUST BE CORRECTED BEFORE RETURNING THE APPLIANCE TO THE CUSTOMER. 2. PRODUCT SAFETY NOTICE
Many electrical and mechanical parts in the appliance have special safety related characteristics. These are often not evident from visual inspection nor the protection afforded by them necessarily can be obtained by using replacement components rated for voltage, wattage, etc. Replacement parts which have these special safety characteristics are identified in this Service Manual. Electrical components having such features are identified by marking with a on the schematics and on the parts list in this Service Manual. The use of a substitute replacement component which does not have the same safety characteristics as the PIONEER recommended replacement one, shown in the parts list in this Service Manual, may create shock, fire, or other hazards. Product Safety is continuously under review and new instructions are issued from time to time. For the latest information, always consult the current PIONEER Service Manual. A subscription to, or additional copies of, PIONEER Service Manual may be obtained at a nominal charge from PIONEER.

Device under test Test all exposed metal surfaces

Leakage current tester

Reading should not be above 0.5 mA

Also test with plug reversed (Using AC adapter plug as required)

Earth ground

AC Leakage Test

2

M-IS22

2. EXPLODED VIEWS AND PARTS LIST
NOTES: Parts marked by "NSP" are generally unavailable because they are not in our Master Spare Parts List. The mark found on some component parts indicates the importance of the safety factor of the part. Therefore, when replacing, be sure to use parts of identical designation. Screws adjacent to mark on product are used for disassembly.

2.1 PACKING
6 5 7

MYXJ Type Only 4 1 Red

2

White

3

8

(1) PACKING PARTS LIST
Mark No.
1 2 3 4 5 6 7 8

Description
Power Cord RCA pin-plug stereo cable (L=1m) System Cable Polyethylene Bag Packing Sheet Protector L(A) Protector R(A) Packing Case A(MY)

Part No.
See Contrast table (2) PDE1126 XDE3042 Z21-038 AHG7053 XHA3122 XHA3123 XHD3170

NSP

(2) CONTRAST TABLE
M-IS22/MYXJ and NVXJ are constructed the same except for the following :
Mark No.
1 Power Cord

Symbol and Description

Part No. MYXJ Type
ADG1154

NVXJ Type
Not used

Remarks

3

M-IS22 2.2 EXTERIOR
41 37 31 41 29 37 37

38

41 23 18 39 32

39 39 41 24 22 7 39 30 39 39 39 9 1 25 33 35 6
2 C1 1 C1

41

15 42 NVXJ Only

26

28 27 21

20

41

41

4

5 44

37

8

19 43

31 41

11

41

4

M-IS22

Caution when disassemble. Even if the power supply code is pulled out from the outlet, neither C11 nor C12 of AF ASSY are discharged. Please discharge C11 and C12 of AF ASSY by the resistor of 100 or more before removing AF ASSY or POWER SUPPLY ASSY. There is a possibility to destroy the transistor, and Please discharge by the resistor of 100 or more.
36 36 12 2 17

34 14 34

13 10

34

34

14

36

36 16 40 3 40

(1) EXTERIOR PARTS LIST
Mark No.
NSP NSP NSP NSP NSP NSP NSP 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20

Description
MAIN Assy AMP Assy POWER SUPPLY Assy PRIMARY Assy SECONDARY Assy HP Assy BLUE LED Assy Power Transformer Fuse (FU1 : 3.15A) DC Fan Motor Chassis A Holder Power Pac Holder Heat Sink Rear Panel A (MY) Mold A Mold B Reflector A Binder Standby Button

Part No.
XWZ3418 XWZ3419 XWZ3420 XWZ3421 XWZ3422 XWZ3423 XWZ3488 ATS7247 REK1027 AXM7014 ANA7086 ANG7009 ANG7109 ANH7058 XNC3107 AMR7005 AMR7006 XMR3041 ZCA-SKB90BK XAD3096

Mark No.
21 22 23 24 25 26 27 28 29 30 NSP 31 32 33 34 35 36 37 38 39 40 41 42 43 44

Description
Standby Lens AMP Lens LT Conductor A Side Duct L Side Duct R AMP Twin L AMP Twin R AMP Escutcheon Top Panel Front Panel A Side Bonnet ICP Label Screw With Washer Screw Screw Screw Screw Screw Screw Screw Screw Name Label BIND Assy Screw

Part No.
XAK3193 XAK3194 XAK3219 XAK3220 XAK3221 XAK3222 XAK3223 XAK3226 XAN3031 XMB3046 ANE7242 AAX7738 ABA1005 ABA1021 BBT40P060FZK BBZ30P180FMC BPZ30P080FZK BMZ30P060FZK BPZ30P100FZK BPZ30P350FZK VBZ30P060FZK See Contrast table (2) ····· BBZ30P080FMC

NSP

NSP

(2) CONTRAST TABLE
Mark No.
42 Name Label

M-IS22/MYXJ and NVXJ are constructed the same except for the following :
Symbol and Description Part No. MYXJ Type
Not used

NVXJ Type
XAL3088

Remarks

5

1

2

3

4

M-IS22

3. SCHEMATIC DIAGRAM
A

3.1 OVERALL WIRING CONNECTION DIAGRAM

+15V +8V

V+5.6V

G
B

POWER SUPPLY ASSY (XWZ3420)

-12V

IC24

VL-

+12V

IC23

VL+

-12V

+15V IC35 UNB1 Q33

+12V +12V

A

MAIN ASSY (XWZ3418)

+8V

IC35 UNB2 Q43 +12V

C

E

BLUE LED ASSY (XWZ3488)

SPEAKER RELAY RY3601 (ASR7008)

D
D

HP ASSY (XWZ3423)

6
1 2 3 4

5

6

7

8

M-IS22

Note : When ordering service parts, be sure to refer to "EXPLODED VIEWS and PARTS LIST" or "PCB PARTS LIST" A

V+5.6V IC82 D81-D84 T1 AN1 BKP1046 RY81

C
VH+ D11 VHVL+ D21 VL-

SECONDARY ASSY (XWZ3422)
B

B
D31­D34 UNB1 D41­D44 UNB2

PRIMARY ASSY (XWZ3421)

C

F
10

AMP ASSY (XWZ3419)
6

POWER AMP.

IC3301 (STK407-070)

D

7
5 6 7 8

1

2

3

4

M-IS22

3.2 MAIN, PRIMARY, SECONDARY, HP and BLUE LED ASSYS
A

A

MAIN ASSY (XWZ3418)

B

C

D

G CN3002
8

F

CN3006

F

CN3003

A

1

2

3

4

5

6

7

8

M-IS22

A
: AUDIO SIGNAL ROUTE

D

HP ASSY (XWZ3423)
B

BLUE LED ASSY S560 : STANDBY/ON

E
BLUE LED ASSY (XWZ3488)

C SECONDARY ASSY (XWZ3422)

B

PRIMARY ASSY (XWZ3421)
C

CAUTION : FOR CONTINUED PROTECTION AGAINST RISK OF FIRE, REPLACE ONLY WITH SAME TYPE NO. 491007, MFD BY LITTELFUSE INK. FOR IC11, IC12 (AEK7021). CAUTION : FOR CONTINUED PROTECTION AGAINST RISK OF FIRE, REPLACE ONLY WITH SAME TYPE NO. 491005, MFD BY LITTELFUSE INK. FOR IC21, IC22 (AEK7019). CAUTION : FOR CONTINUED PROTECTION AGAINST RISK OF FIRE, REPLACE ONLY WITH SAME TYPE NO. 491004, MFD BY LITTELFUSE INK. FOR IC31 (AEK7018).
AC POWER CORD MYXJ TYPE : ADG1154 NVXJ TYPE : ADG1156 AC220-230V

REK1027 (T3.15A)

· NOTE FOR FUSE REPLACEMENT CAUTION - FOR CONTINUED PROTECTION AGAINST RISK OF FIRE. REPLACE WITH SAME TYPE AND RATINGS ONLY.

CAUTION : FOR CONTINUED PROTECTION AGAINST RISK OF FIRE, REPLACE ONLY WITH SAME TYPE NO. 49103.5, MFD BY LITTELFUSE INK. FOR IC41 (AEK7017).

D

5

6

A B C D E
7 8

9

1

2

3

4

M-IS22

3.3 AMP and POWER SUPPLY ASSYS
A

F

AMP ASSY (XWZ3419)

: AUDIO SIGNAL ROUTE

B

C

D

10

F

1

2

3

4

A

CN3106

A

CN3103

5

6

7

8

M-IS22

A
CAUTION : FOR CONTINUED PROTECTION AGAINST RISK OF FIRE, REPLACE ONLY WITH SAME TYPE NO. 4911.25, MFD BY LITTELFUSE INK. FOR IC33 (AEK7048). CAUTION : FOR CONTINUED PROTECTION AGAINST RISK OF FIRE, REPLACE ONLY WITH SAME TYPE NO. 491002, MFD BY LITTELFUSE INK. FOR IC42 (AEK7067).

G

POWER SUPPLY ASSY (XWZ3420)

B

C

A
D 5 6 7

G
8

11

CN3102

1

2

3

4

M-IS22

4. PCB CONNECTION DIAGRAM
A
NOTE FOR PCB DIAGRAMS:
1. Part numbers in PCB diagrams match those in the schematic diagrams. 2. A comparison between the main parts of PCB and schematic diagrams is shown below.
Symbol in PCB Diagrams Symbol in Schematic Diagrams Part Name

3. The parts mounted on this PCB include all necessary parts for several destination. For further information for respective destinations, be sure to check with the schematic diagram. 4. Viewpoint of PCB diagrams

Capacitor
B B C E B B C E D D G S G S D G S Field effect transistor C E B C E Transistor with resistor C E B C E Transistor

Connector

SIDE A

P.C.Board

Chip Part

SIDE B

Resistor array

B
3-terminal regulator

4.1 PRIMARY and SECONDARY ASSYS

C
SECONDARY ASSY

B
PRIMARY ASSY

C

A
J3001

(XNP3050-B)
D

SIDE A

POWER TRANSFORMER

A

A

N BLUE L BROWN

12

B C
1

2

3

4

1

2

3

4

M-IS22

4.2 HP and BLUE LED ASSYS

E
BLUE LED ASSY

E
BLUE LED ASSY
Q5604 Q5601

A

IC5601

A CN3015

B

Q5602 Q5603

C

D
HP ASSY

A CN3104

D
HP ASSY

D (XNP3050-B) (XNP3050-B)

SIDE A

SIDE B

1

2

3

D E
4

13

1

2

3

4

M-IS22 4.3 MAIN ASSY
F
A
IC3302

CN3006

F
CN3003

XC-IS22CD

D
J3004

G
B

CN3002

E
J3005

IC81

IC82 Q81

C
J3001

C

A
MAIN ASSY
L BROWN

B B
N BLUE AC IN
LIVE NEUTRAL

D

SIDE A
(XNP3050-B)

14

A

1

2

3

4

1

2

3

4

M-IS22

A
MAIN ASSY
SIDE B
Q85 Q3603 Q3601 Q3313 Q3602
A

Q3607 Q3608 Q3606 Q3605

B

(XNP3050-B)

Q3621

Q82

C

D

1

2

3

4

A

15

1

2

3

4

M-IS22 4.4 AMP and POWER SUPPLY ASSYS

G
A

POWER SUPPLY ASSY

IC24 IC23 Q33 Q43

Q42 Q32

Q3651

Q53 Q3654 IC52 IC33 IC42

B

A CN3102 A CN3106 A CN3103
Q3502 Q3501

F
C

AMP ASSY

IC3301

D

SIDE A
(XNP3050-B) Q3352 Q3351

16

F G
1

2

3

4

1

2

3

4

M-IS22

G
IC32 Q31 Q41

POWER SUPPLY ASSY

A

IC61 Q3652 Q3653 Q51

B

F
Q3311 Q3312

AMP ASSY

C

Q3503 IC3502 IC3501

Q3353 Q3354

D

SIDE B
(XNP3050-B)

1

2

3

F G
4

17

M-IS22

5. PCB PARTS LIST
NOTES: Parts marked by "NSP" are generally unavailable because they are not in our Master Spare Parts List. The mark found on some component parts indicates the importance of the safety factor of the part. Therefore, when replacing, be sure to use parts of identical designation. When ordering resistors, first convert resistance values into code form as shown in the following examples. Ex.1 When there are 2 effective digits (any digit apart from 0), such as 560 ohm and 47k ohm (tolerance is shown by J=5%, and K=10%). 560 56 x 101 RD1/4PU 5 6 1 J 561 47k RD1/4PU 4 7 3 J 47 x 103 473 0.5 RN2H R 5 0 K R50 1 RS1P 1 R 0 K 1R0 Ex.2 When there are 3 effective digits (such as in high precision metal film resistors). 5.62k 562 x 101 5621 RN1/4PC 5 6 2 1 F
Description Part No.
XWK3030 XWZ3418 XWZ3419 XWZ3420 XWZ3421 XWZ3422 XWZ3423 XWZ3488

Mark No.
NSP NSP NSP NSP NSP NSP NSP NSP

Mark No.

Description

Part No.

LIST OF ASSEMBLIES
MAIN ASSY MAIN ASSY AMP ASSY POWER SUPPLY ASSY PRIMARY ASSY SECONDARY ASSY HP ASSY BLUE LED ASSY

CAPACITORS
C1­C3 (10000pF/AC275V) C3345, C3346 (10000pF/100V) C11, C12 (2200µF/71v) C3551­C3554 C3602, C84 C83 C3601 C41 C31 C3621 C21, C22 C82 C3325 C3335­C3338 C3331­C3334 C9011 C9021 ACE7013 ACG7021 ACH7117 CCSRCH331J50 CEAT100M50 CEAT1R0M50 CEAT221M16 CEAT222M25 CEAT222M35 CEAT2R2M2A CEAT332M35 CEAT471M25 CEATR10M50 CKSRYB103K50 CKSRYB104K25 CQMA102K2E CQMA223K2E

A

MAIN ASSY
IC82 Q3601, Q3621 Q3602, Q3603, Q3605­Q3608 Q81 Q85 Q3313 Q82 D3601, D3603, D3609, D3621 D3625, D3626, D3651, D3652 D85­D87 D11, D21 D3608 D31­D34, D41­D44 D81­D84 NJM78M56FA 2SA1037K 2SC2412K 2SD1859X DTA114TK DTA124EK DTC124EK 1SS133 1SS133 1SS133 D3SBA20(B) MTZJ5.6C S5566G(TPB2) S5688G

SEMICONDUCTORS

RESISTORS
R3333, R3334 R82 R3601, R3602 Other Resistors RD1/4MUF101J RD1/4PU220J RS3LMFR22J RS1/16S&&&J

OTHERS
CN3015 JA3333 CN3332 CN3103 CN3106 CN3102 H1, H2 AN1 J3001 9P JUMPER CONNECTOR 2P PIN JACK 10P SOCKET 5P CONNECTOR SOCKET 14P SOCKET 17P CONNECTOR SOCKET FUSE CLIP AC INLET 1P JUMPER WIRE BARRIER CAP 52151-0910 AKB7043 AKP7048 AKP7147 AKP7153 AKP7159 AKR7001 BKP1046 D20PYY1420E XEC3023 XKE3001

COILS AND FILTERS
L1 LINE FILTER L3331­L3334 (1µH) ATF7019 ATH-133

TRANSFORMERS
T1 STANDBY TRANSFORMER XTT3004

SWITCHES AND RELAYS
RY3601 RY81 SP RELAY/12V ASR7008 ASR7018 CN3331 4P SPEAKER TERMINAL

18

M-IS22

Mark No.

Description

Part No.

Mark No.

Description

Part No.

B C

PRIMARY ASSY
PRIMARY assembly has no service part.

F

AMP ASSY
IC3501, IC3502 IC3301 Q3354 Q3353 Q3311, Q3312 BA4558F-HT STK407-070B 2SA1037K 2SC2412K 2SD2114K 2SK246 DTA124EK IRFI9Z34G IRFIZ34G 1SR139-100 1SS133 LT2A03 MTZJ10C MTZJ18B MTZJ39C

SEMICONDUCTORS

SECONDARY ASSY
IC41 PROTECTOR(3.5A) IC31 PROTECTOR(4A) IC21, IC22 PROTECTOR(5A) IC11, IC12 PROTECTOR(7A) AEK7017 AEK7018 AEK7019 AEK7021

SEMICONDUCTORS

D

Q3501, Q3502 Q3503 Q3351 Q3352 D3301, D3302 D3351­D3354, D3361, D3362 D3355, D3356 D3357, D3358 D3359, D3360 D3363, D3364

HP ASSY
L3992­L3994 CHIP BEADS VTL1096

COILS AND FILTERS

CAPACITORS
C3991, C3995, C3996 CKSRYB472K50

RESISTORS
R3991, R3992 RS2LMF331J

CAPACITORS
C3327, C3328 C3317, C3318 C3313, C3314 C3303, C3304 C3506­C3508 C3501, C3502, C3509, C3510 C3315, C3316 C3503, C3504 C3308 CCSRCH680J50 CEANP100M35 CEANPR47M50 CEAT101M50 CEAT1R0M50 CEAT470M25 CKSRYB332K50 CKSRYB682K50 CKSRYB822K50

OTHERS
3004 3991 J3004 5P CABLE HOLDER MINI JACK 5P JUMPER WIRE 51048-0500 AKN7003 D20PYY0530E

E

BULE LED ASSY
Q5601, Q5603 Q5602 D5607, D5608 D5603 D5604 2SC2412K DTC124EK 1SS355 E1L4E-7B1A(2345) SLR-343VC(NPQ)

SEMICONDUCTORS

RESISTORS
R3353, R3354 R3510 Other Resistors RD1/4PU101J RD1/4PU104J RS1/16S&&&J

OTHERS
CN3003 5P CONNECTOR PLUG CN3006 11P CONNECTOR PLUG AKM7059 AKM7065

SWITCHES AND RELAYS
S5601 ASG7013

RESISTORS
R5626 Other Resistors RD1/4PU332J RS1/16S&&&J

G

POWER SUPPLY ASSY
IC33 IC42 IC32 IC23 IC24 PROTECTOR(1.25A) PROTECTOR(2A) AEK7048 AEK7067 BA4558F-HT NJM7805FA NJM7905FA 2SB1375 2SC1740S 2SC2412K DTA143ES DTC124EK

SEMICONDUCTORS

OTHERS
302 J3005 9P CABLE HOLDER JUMPER WIRE LED SPACER 51048-0900 D20PYY0925E XEB3018

Q33, Q43 Q32, Q3654, Q42 Q3652 Q3651 Q3653

19

M-IS22

Mark No.

Description

Part No.
1SS133 1SS133 MTZJ24B MTZJ3.0B MTZJ5.1B MTZJ6.8C

6. ADJUSTMENT
There is no information to be shown in this chapter.

D3654­D3656, D9021­D9024, D9026 D9029 D9030 D36, D46 D35, D45 D9027, D9028

CAPACITORS
C27, C28, C35, C45 C3652 C25, C26, C3651 C3654 C42, C43 C32, C33 C44 C3653, C9027, C9028 CEAT100M50 CEAT101M16 CEAT1R0M50 CEAT220M50 CEAT470M16 CEAT470M25 CKSRYB102K50 CKSRYB104K25

RESISTORS
R35 R45 R3659 Other Resistors RD1/2LMF121J RD1/2LMF820J RD1/2PM330J RS1/16S&&&J

OTHERS
CN3002 17P CONNECTOR PLUG CN3651 2P PLUG AKM7071 KM200SA2

20

M-IS22

7. GENERAL INFORMATION
7.1 SINGLE OPERATION METHOD
Single operation method and inputlevel.
The procedure and the input level of a single operation are shown below. 1. R85 are shorted by 1k. 2. A point of the figure below in four places is connected. GND is not common because it is independent with chassis GND (GND of the amplifier), B1GND, B2GND, and B3GND. The potential of B1GND, B2GND, and B3GND is done by connecting A point in four places as well as chassis GND. 2. The power supply of the product is turned on. 3. The terminal CONT (2 pin of CN3332) are controlled respectively by the following voltages. CONT 5V ON ON

RY MUTE

12V ON OFF

0V OFF ON

4. The signal of 10mV is input from input terminal (JA3333), and the output is confirmed with speaker terminal (CN3331). Note : If the music signal is input directly to input terminal (JA3333) with CD PLAYER etc. , the output becomes a large volume because there are 40dB GAIN of the amplifier.

A MAIN

ASSY

CONNECT A POINT (GND) (FOUR PLACES) INPUT SIGNAL 10mV CONTROLL 0V, 5V or 12V

SIDE B

OUTPUT SIGNAL

R85 ­ 1k

Caution when disassemble. Even if the power supply code is pulled out from the outlet, neither C11 nor C12 of AF ASSY are discharged. Please discharge C11 and C12 of AF ASSY by the resistor of 100 or more before removing AF ASSY or POWER SUPPLY ASSY. There is a possibility to destroy the transistor, and Please discharge by the resistor of 100 or more.

21

M-IS22

8. PANEL FACILITIES AND SPECIFICATIONS
¶ PANEL FACILITIES ¶ SPECIFICATIONS Amplifier section
Continuous Power (RMS) ............. 100 W + 100 W (1 kHz, THD 10%, 6 ) Continuous Power (DIN) .................. 65 W + 65 W (1 kHz, THD 1%, 6 ) Music Power (DIN) ....................... 150 W + 150 W (1 kHz, THD 1%, 6 )

POWER AMPLIFIER M-IS22 AERO DUCT CONSTRUCTION

Miscellaneous
Power Requirements ....... AC 220-230 V, 50/60 Hz Power Consumption .................................... 140 W Power Consumption in standby mode ............. 1 W Dimensions: Power Amplifier . 160 (W) x 300 (H) x 237 (D) mm Weight: Power Amplifier ........................................... 4.1 kg

STANDBY/ON

STANDBY

30 31
PHONES

29

Accessories
Power cord (MYXJ Type) ..................................... 1 System cable ...................................................... 1 RCA pin-plug stereo cable .................................. 1 Note Specifications and design subject to possible modification without notice, due to improvements.

29 STANDBY/ON 30 Standby indicator 31 Headphone jack

22