Text preview for : DCR-PC2E.PDF part of Sony DCR-PC2E Digital video camera SONY DCR-PC2E, PC3, PC3E - service manual
Back to : dcr-pc2e.rar | Home
DCR-PC2E/PC3/PC3E
RMT-809/811/812
SERVICE MANUAL
Ver 1.0 1999. 06
Canadian Model Korea Model
DCR-PC3
AEP Model UK Model
DCR-PC2E/PC3E
Australian Model Chinese Model
DCR-PC3E
D300 MECHANISM
Photo : DCR-PC3 RMT-811
E Model Hong Kong Model Tourist Model
DCR-PC3/PC3E
DCR-PC3 : NTSC model DCR-PC2E/PC3E : PAL model
For MECHANISM ADJUSTMENTS, refer to the "DV MECHANICAL D MECHANISM " (original: 9-973-815ADJUSTMENT MANUAL 11, supplement: 9-973-815-81) and "DV MECHANICAL ADJUSTMENT D200 MECHANISM " (original: 9-973-981-11). MANUAL
SPECIFICATIONS
-- Continued on next page --
DIGITAL VIDEO CAMERA RECORDER
MICROFILM
· SUPPLIED ACCESSORIES
Check that the following accessories are supplied with your camcorder.
· DIFFERENCE TABLE
Model Color System Remote Commander Lens Memory Stick Memory Key DV AUDIO/VIDEO Optical Digital DCR-PC2E PAL RMT-809 10 × 120 ×, 40 × * -- -- IN/OUT * OUT_only IN/OUT * OUT_only DCR-PC3 NTSC RMT-811 10 × 120 × g g IN/OUT IN/OUT DCR-PC3E PAL RMT-811 RMT-812 * 10 × 120 ×, 40 × * g g IN/OUT * OUT_only IN/OUT * OUT_only · Abbreviation AUS: Australian model JE: Tourist model CND: Canadian model CN: Chinese model HK: Hong Kong model KR: Korea model
*: AEP, UK model
SAFETY-RELATED COMPONENT WARNING!! COMPONENTS IDENTIFIED BY MARK ! OR DOTTED LINE WITH MARK ! ON THE SCHEMATIC DIAGRAMS AND IN THE PARTS LIST ARE CRITICAL TO SAFE OPERATION. REPLACE THESE COMPONENTS WITH SONY PARTS WHOSE PART NUMBERS APPEAR AS SHOWN IN THIS MANUAL OR IN SUPPLEMENTS PUBLISHED BY SONY.
ATTENTION AU COMPOSANT AYANT RAPPORT À LA SÉCURITÉ! LES COMPOSANTS IDENTIFÉS PAR UNE MARQUE ! SUR LES DIAGRAMMES SCHÉMATIQUES ET LA LISTE DES PIÈCES SONT CRITIQUES POUR LA SÉCURITÉ DE FONCTIONNEMENT. NE REMPLACER CES COMPOSANTS QUE PAR DES PIÈSES SONY DONT LES NUMÉROS SONT DONNÉS DANS CE MANUEL OU DANS LES SUPPÉMENTS PUBLIÉS PAR SONY.
SAFETY CHECK-OUT
After correcting the original service problem, perform the following safety checks before releasing the set to the customer. 1. Check the area of your repair for unsoldered or poorly-soldered connections. Check the entire board surface for solder splashes and bridges. Check the interboard wiring to ensure that no wires are "pinched" or contact high-wattage resistors. Look for unauthorized replacement parts, particularly transistors, that were installed during a previous repair. Point them out to the customer and recommend their replacement. 4. Look for parts which, through functioning, show obvious signs of deterioration. Point them out to the customer and recommend their replacement. 5. Check the B+ voltage to see it is at the values specified. 6. Flexible Circuit Board Repairing · Keep the temperature of the soldering iron around 270°C during repairing. · Do not touch the soldering iron on the same conductor of the circuit board (within 3 times). · Be careful not to apply force on the conductor when soldering or unsoldering.
2. 3.
--2--
TABLE OF CONTENTS SERVICE NOTE
1. 2. POWER SUPPLY DURING REPAIRS ····························· 6 TO TAKE OUT A CASSETTE WHEN NOT EJECT (FORCE EJECT) ································································ 6 Copying still images from a mini DV tape Photo save ······ 1-27 Viewing a still picture Memory photo playback ················ 1-27 Playing back images in a continuous loop SLIDE SHOW ·· 1-28 Preventing accidental erasure Image protection ················ 1-29 Deleting images ··································································· 1-29 Writing a print mark PRINT MARK ································· 1-30 Additional Information ···························································· 1-30 Using the viewfinder ···························································· 1-30 Usable cassettes ··································································· 1-30 Troubleshooting ··································································· 1-31 Self-diagnosis display ·························································· 1-32 Warning indicators and messages ········································ 1-33 Using your camcorder abroad ·············································· 1-33 Maintenance information and precautions ··························· 1-33 Quick Reference ······································································ 1-35 Identifying the parts and controls ········································ 1-35
SELF-DIAGNOSIS FUNCTION
1. 2. 3. SELF-DIAGNOSIS FUNCTION ······································· 7 SELF-DIAGNOSIS DISPLAY ·········································· 7 SELF-DIAGNOSIS CODE TABLE ··································· 8
1.
GENERAL
Checking supplied accessories ·················································· 1-1 Quick Start Guide ······································································ 1-1 Getting started ··········································································· 1-1 Using this manual ·································································· 1-1 Step 1 Preparing the power supply ········································ 1-2 Charging the battery pack ···················································· 1-2 Installing battery pack ·························································· 1-3 Connecting to the mains ······················································ 1-3 Step 2 Inserting a cassette ······················································ 1-3 Step 3 Using a touch panel ···················································· 1-3 Recording Basics ····································································· 1-4 Recording a picture ································································ 1-4 Shooting backlit subjects (BACK LIGHT) ·························· 1-6 Shooting in the dark (NightShot) ········································· 1-6 END SEARCH ···································································· 1-6 Playback Basics ······································································· 1-6 Playing back a tape ································································ 1-6 Viewing the recording on TV ················································ 1-8 Advanced Recording Operations ··············································· 1-8 Photo recording ······································································ 1-8 Using the wide mode ····························································· 1-9 Using the fader function ························································ 1-9 Using special effects Picture effect ···································· 1-10 Using special effects Digital effect ···································· 1-10 Adjusting the white balance manually ································· 1-11 Using the PROGRAM AE function ····································· 1-11 Adjusting the exposure manually ········································ 1-12 Focusing manually ······························································· 1-12 Advanced Playback Operations ··············································· 1-13 Playing back a tape with picture effects ······························ 1-13 Playing back a tape with digital effects ······························· 1-13 Quickly locating a scene using the zero set memory function ················································································ 1-13 Searching a recording by date Date search ························ 1-13 Searching the boundaries of recorded tape by title Title search ········································································· 1-14 Searching for a photo-Photo search/Photo scan ·················· 1-14 Editing ····················································································· 1-15 Dubbing a tape ····································································· 1-15 Editing partially on a DV tape DV synchro-editing ·········· 1-15 Recording video or TV programmes ··································· 1-16 Inserting a scene from a VCR ·············································· 1-17 Audio dubbing ····································································· 1-18 Superimposing a title ··························································· 1-19 Making your own titles ························································ 1-19 Labeling a cassette ······························································· 1-20 Customizing Your Camcorder ················································· 1-20 Changing the menu settings ················································· 1-20 Resetting the date and time ·················································· 1-22 "Memory Stick" operations ····················································· 1-22 Using a "Memory Stick" introduction ······························· 1-22 Recording still images on "Memory Stick"s Memory photo recording ··················································· 1-24 Superimposing a still picture in a "Memory Stick" on a moving picture MEMORY MIX ································ 1-25 Recording an image from a mini DV tape as a still image ·· 1-26
2.
DISASSEMBLY
2-1. LCD UNIT, PD-112 BOARD ········································· 2-2 2-2. CABINET (R) BLOCK ASSEMBLY ····························· 2-3 2-3. DD-125, VC-220 BOARDS, EVF BLOCK ASSEMBLY ············································· 2-4 2-4. MR-41 BOARD, MD BLOCK ········································ 2-5 2-5. VF-136, CD-221 BOARDS ············································· 2-6 2-6. LCD HINGE ASSEMBLY ·············································· 2-7 2-7. ATTACHING HARNESSES OF THE LCD HINGE ASSEMBLY ···································································· 2-8 2-8. CONTROL SWITCH BLOCK (FK-4750), SPEAKER (2.0 CM) ······················································· 2-9 2-9. CIRCUIT BOARDS LOCATION ································· 2-10 2-10. FLEXIBLE BOARDS LOCATION ······························ 2-11
3.
BLOCK DIAGRAMS
3-1. OVERALL BLOCK DIAGRAM (DCR-PC2E MODEL) ···················································· 3-1 3-2. OVERALL BLOCK DIAGRAM (DCR-PC3/PC3E MODEL) ············································ 3-5 3-3. POWER BLOCK DIAGRAM ········································· 3-9
4.
PRINTED WIRING BOARDS AND SCHEMATIC DIAGRAMS
4-1. FRAME SCHEMATIC DIAGRAM ································ 4-1 4-2. PRINTED WIRING BOARDS AND SCHEMATIC DIAGRAMS ············································ 4-5 · CD-221 (CCD IMAGER) PRINTED WIRING BOARD AND SCHEMATIC DIAGRAM ······························ 4-6 · VC-220 (CAMERA CONTROL)(1/9) SCHEMATIC DIAGRAM ······························ 4-9 · VC-220 (DS CONTROL · HONEY)(2/9) SCHEMATIC DIAGRAM ···························· 4-12 · VC-220 (LINE OUT AMP, BBI)(3/9) SCHEMATIC DIAGRAM ···························· 4-15 · VC-220 (VFD-CPS)(4/9) SCHEMATIC DIAGRAM ···························· 4-18 · VC-220 (SFD, LIP, TFD-CSP)(5/9) SCHEMATIC DIAGRAM ···························· 4-21 · VC-220 (EVF DRIVER)(6/9) SCHEMATIC DIAGRAM ···························· 4-24 · VC-220 (AUDIO PROCESSOR)(7/9) SCHEMATIC DIAGRAM ···························· 4-27 · VC-220 (MECHA SP CONTROL)(8/9) SCHEMATIC DIAGRAM ···························· 4-29 · VC-220 (CME HI CONTROL)(9/9) SCHEMATIC DIAGRAM ···························· 4-31 · PR-32 (PANEL REVERSE), PO-4 (PANEL OPEN) PRINTED WIRING BOARDS ····················· 4-34
--3--
· VC-220 (CAMERA CONTROL, HONEY, LINE OUT, VFD-CPS, SFD, LIP, TFD-CSP, EVF DRIVER, AUDIO PROCESSOR, MECHA SP CONTROL, CME HI CONTROL) PRINTED WIRING BOARD ······················· 4-37 · MR-41 (DRUM/CAPSTAN MOTOR DRIVE, REC/PB HEAD AMP) PRINTED WIRING BOARD ······················· 4-43 · MR-41 (DRUM/CAPSTAN MOTOR DRIVE)(1/2) SCHEMATIC DIAGRAM ···························· 4-45 · FP-91 (MODE), FP-92 (TOP/END SENSOR, TAPE LED), FP-242 (S/T REEL SENSOR) PRINTED WIRING BOARDS ····················· 4-49 · MR-41 (REC/PB HEAD AMP)(2/2) SCHEMATIC DIAGRAM ···························· 4-50 · CONTROL SWITCH BLOCK (FK-4750) SCHEMATIC DIAGRAM ···························· 4-53 · PD-112 (RGB DECODER, TIMING GENERATOR) PRINTED WIRING BOARD ······················· 4-55 · PD-112 (RGB DECODER)(1/2) SCHEMATIC DIAGRAM ···························· 4-57 · PD-112 (TIMING GENERATOR)(2/2) SCHEMATIC DIAGRAM ···························· 4-60 · VF-136 (BACK LIGHT DRIVE) PRINTED WIRING BOARD AND SCHEMATIC DIAGRAM ···························· 4-63 · TB-38 (BATTERY TERMINAL), DD-125 (DC/DC CONVERTER) PRINTED WIRING BOARDS ····················· 4-67 · TB-38 (BATTERY TERMINAL), DD-125 (DC/DC CONVERTER) SCHEMATIC DIAGRAM ···························· 4-71
1.
5.
1. 1-1. 5-1. 1-1.
ADJUSTMENTS
Before starting adjustment ··············································· 5-1 Adjusting items when replacing main parts and boards ···· 5-2 CAMERA SECTION ADJUSTMENT ··························· 5-4 PREPARATIONS BEFORE ADJUSTMENT (CAMERA SECTION) ··················································· 5-4 1-1-1. List of Service Tools ························································ 5-4 1-1-2. Preparations ····································································· 5-5 1-1-3. Precaution ········································································ 5-7 1. Setting the Switch ···························································· 5-7 2. Order of Adjustments ······················································ 5-7 3. Subjects ··········································································· 5-7 1-2. INITIALIZATION OF B, C, D, E, F PAGE DATA ········ 5-8 1-2-1. INITIALIZATION OF C PAGE DATA ··························· 5-8 1. Initializing the C Page Data ············································· 5-8 2. Modification of C Page Data ··········································· 5-8 3. C Page Table ···································································· 5-8 1-2-2. INITIALIZATION OF D PAGE DATA ························ 5-10 1. Initializing the D Page Data ·········································· 5-10 2. Modification of D Page Data ········································· 5-10 3. D Page Table ·································································· 5-11 1-2-3. INITIALIZATION OF B PAGE DATA (DCR-PC3/PC3E) ························································· 5-12 1. Initializing the B Page Data ··········································· 5-12 2. Modification of B Page Data ········································· 5-12 3. B Page Table ·································································· 5-13 1-2-4. INITIALIZATION OF E, F PAGE DATA ····················· 5-14 1. Initializing the E, F Page Data ······································· 5-14 2. Modification of E, F Page Data ····································· 5-14 3. F Page Table ·································································· 5-15 4. E Page Table ·································································· 5-17 1-3. CAMERA SYSTEM ADJUSTMENTS ························ 5-19
36 MHz Origin Oscillation Adjustment (VC-220 board) ····························································· 5-19 2. Zoom Key Center Adjustment ······································· 5-19 3. HALL Adjustment ························································· 5-19 4. Flange Back Adjustment (Using Minipattern Box) ······· 5-20 5. Flange Back Adjustment (Using Flange Back Adjustment Chart and Subject More Than 500m Away) ················································ 5-21 5-1. Flange Back Adjustment (1) ·········································· 5-21 5-2. Flange Back Adjustment (2) ·········································· 5-21 6. Flange Back Check ························································ 5-22 7. Optical Axis Adjustment ··············································· 5-23 8. Picture Frame Setting ···················································· 5-24 9. AGC GAIN Calibration Adjustment ····························· 5-24 10. Color Reproduction Adjustment ···································· 5-25 11. MAX GAIN Adjustment ··············································· 5-25 12. Auto White Balance & LV Standard Data Input ··········· 5-26 13. Auto White Balance Adjustment ··································· 5-26 14. White Balance Check ···················································· 5-27 15. Angular Velocity Sensor Sensitivity Preset ··················· 5-27 1-4. COLOR ELECTRONIC VIEWFINDER SYSTEM ADJUSTMENT ············································ 5-28 1. VCO Adjustment (VC-220 board) ································ 5-28 2. Bright Adjustment (VC-220 board) ······························· 5-29 3. Contrast Adjustment (VC-220 board) ··························· 5-29 4. White Balance Adjustment (VC-220 board) ················· 5-30 1-5. LCD SYSTEM ADJUSTMENT ··································· 5-31 1. VCO Adjustment (PD-112 board) ································· 5-31 2. Black Limit Adjustment (PD-112 board) ······················ 5-32 3. Bright Adjustment (PD-112 board) ······························· 5-32 4. Gamma-1 Adjustment (PD-112 board) ························· 5-33 5. Contrast Adjustment (PD-112 board) ···························· 5-33 6. Center Level Adjustment (PD-112 board) ····················· 5-34 7. White Balance Adjustment (PD-112 board) ·················· 5-34 5-2. MECHANISM SECTION ADJUSTMENT ·················· 5-35 2-1. HOW TO ENTER RECORD MODE WITHOUT CASSETTE ··································································· 5-35 2-2. HOW TO ENTER PLAYBACK MODE WITHOUT CASSETTE ················································ 5-35 2-3. TAPE PATH ADJUSTMENT ········································ 5-35 1. Preparation for Adjustment ··········································· 5-35 2. Processing after Completing Operations ······················· 5-35 5-3. VIDEO SECTION ADJUSTMENT ······························ 5-36 3-1. PREPARATIONS BEFORE ADJUSTMENTS ············ 5-36 3-1-1. Equipment to Required ·················································· 5-36 3-1-2. Precautions on Adjusting ··············································· 5-37 3-1-3. Adjusting Connectors ···················································· 5-37 3-1-4. Connecting the Equipment ············································ 5-38 3-1-5. Checking the Input Signals (Except AEP/UK model) ··· 5-38 3-1-6. Alignment Tapes ···························································· 5-39 3-1-7. Input/Output Level and Impedance ······························· 5-39 3-2. SYSTEM CONTROL SYSTEM ADJUSTMENT ········ 5-40 1. Initialization of B, C, D, E, F Page Data ······················· 5-40 2. Touch Panel Adjustment (VC-220 board) ····················· 5-40 3. Battery End Adjustment (VC-220 board) ······················ 5-40 3-3. SERVO AND RF SYSTEM ADJUSTMENT ··············· 5-41 1. Cap FG Duty Adjustment (MR-41 board) ····················· 5-41 2. T reel FG Duty Adjustment (MR-41 board) ·················· 5-41 3. PLL f0 & LPF f0 Adjustment (MR-41 board) ················ 5-41 4. Switching Position Adjustment (MR-41 board) ············ 5-42 5. AGC Center Level Adjustment (MR-41 board) ············ 5-42 6. APC & AEQ Adjustment (MR-41 board) ····················· 5-43 7. PLL f0 & LPF f0 Final Adjustment (MR-41 board) ······· 5-43 3-4. VIDEO SYSTEM ADJUSTMENTS ····························· 5-44 3-4-1. Base Band Block Adjustments ······································ 5-44 1. Chroma BPF f0 Adjustment (VC-220 board) ················ 5-44
--4--
2. 3.
S VIDEO OUT Y Level Adjustment (VC-220 board) ··· 5-44 S VIDEO OUT Chroma Level Adjustment (VC-220 board) ····························································· 5-45 4. AV OUT Y, Chroma Level Check (VC-220 board) ······· 5-45 5. PLL Adjustment (VC-220 board) (Except AEP/UK model) ··············································· 5-46 3-4-2. BIST Check ··································································· 5-47 1. Playback System Check ················································ 5-47 1-1. Preparation for Playback ··············································· 5-47 1-2. IC1900(TRX) BIST(PB) Check ···································· 5-47 1-3. IC1601(TFD) BIST(PB) Check ···································· 5-47 1-4. IC1600(SFD) BIST(PB) Check ····································· 5-47 1-5. IC1501(VFD) BIST(PB) Check ···································· 5-48 2. Recording System Check ·············································· 5-49 2-1. Preparations for recording ············································· 5-49 2-2. IC1501(VFD) BIST(REC) Check ································· 5-49 2-3. IC1600(SFD) BIST(REC) Check ·································· 5-49 2-4. IC1601(TFD) BIST(REC) Check ································· 5-50 2-5. IC1900(TRX) BIST(REC) Check ································· 5-50 3-5. AUDIO SYSTEM ADJUSTMENTS ···························· 5-51 1. Playback Level Check ··················································· 5-52 2. Overall Level Characteristics Check ····························· 5-52 3. Overall Distortion Check ··············································· 5-52 4. Overall Noise Level Check ············································ 5-52 5. Overall Separation Check ·············································· 5-52 5-4. SERVICE MODE ·························································· 5-53 4-1. ADJUSTMENT REMOTE COMMANDER ················ 5-53 1. Using the adjustment remote commander ····················· 5-53 2. Precautions upon using the adjustment remote commander ···································································· 5-53 4-2. DATA PROCESS ··························································· 5-54 4-3. SERVICE MODE ·························································· 5-55 1. Setting the Test Mode ···················································· 5-55 2. Emergence Memory Address ········································ 5-55 2-1. EMG Code (Emergency Code) ····································· 5-55 2-2. MSW Code ···································································· 5-56 3. Bit value discrimination ················································ 5-57 4. Switch check (1) ···························································· 5-57 5. Switch check (2) ···························································· 5-58 6. Record of Use check ······················································ 5-58 7. Record of Self-diagnosis check ····································· 5-59
6.
REPAIR PARTS LIST
6-1-1. CABINET (R) SECTION ··············································· 6-1 6-1-2. MAIN BOARD SECTION ·············································· 6-2 6-1-3. CABINET (R) BLOCK ASSEMBLY ····························· 6-3 6-1-4. CABINET (L) SECTION ················································ 6-4 6-1-5. EVF SECTION ································································ 6-5 6-1-6. CASSETTE COMPARTMENT AND DRUM ASSY SECTION ········································································ 6-6 6-1-7. LS CHASSIS SECTION ················································· 6-7 6-1-8. MECHANISM CHASSIS BLOCK SECTION-1 ··········· 6-8 6-1-9. MECHANISM CHASSIS BLOCK SECTION-2 ··········· 6-9 6-2. ELECTRICAL PARTS LIST ········································ 6-10 * The optical axis frame and color reproduction frame are shown on page 242 and 243.
--5--
SERVICE NOTE
1. POWER SUPPLY DURING REPAIRS
In this unit, about 10 seconds after power is supplied to the battery terminal using the regulated power supply (4.2V), the power is shut off so that the unit cannot operate. This following two methods are available to prevent this. Take note of which to use during repairs. Method 1. Connect the servicing remote commander RM-95 (J-6082-053-B) to the LANC jack, and set the commander switch to the "ADJ" side. Method 2. Use the AC power adaptor (AC-VF10 or AC-VQ11) and connecting cord (DK-115).
2.
TO TAKE OUT A CASSETTE WHEN NOT EJECT (FORCE EJECT)
1 Refer to 2-2 to remove the accessory shoe and NS block assembly. 2 Refer to 2-2 to remove the jack ornamental plate. 3 Refer to 2-2 to remove the tripod screw. 4 Refer to 2-2 and 2-3 to remove the cabinet (R) block assembly. 5 Refer to 2-3 to remove the microphone unit. 6 Refer to 2-3 to remove the battery plate. 7 Refer to 2-3 to remove DD-125 board. 8 Refer to 2-3 and 2-4 to remove the cabinet (L) block assembly, lens block and EVF block. 9 Open MR-41 board. !º Disconnect CN2504 (4P, 0.8mm) of MR-41 board. !¡ Add +4.5V from the DC POWER SUPPLY and unload with a pressing the cassette compartment.
: Unloading : Loading
1 -4 D R R M OA B
Loading motor
Disconnect from CN2504 of MR-41 board.
--6--
SELF-DIAGNOSIS FUNCTION
1. SELF-DIAGNOSIS FUNCTION 2. SELF-DIAGNOSIS DISPLAY
When problems occur while the unit is operating, the self-diagnosis function starts working, and displays on the viewfinder or LCD screen what to do. Details of the self-diagnosis functions are provided in the Instruction manual.
Viewfinder or LCD screen
C:31:11
When problems occur while the unit is operating, the counter of the viewfinder or LCD screen consists of an alphabet and 4-digit numbers, which blinks at 3.2 Hz. This 5-character display indicates the "repaired by:", "block" in which the problem occurred, and "detailed code" of the problem.
Blinks at 3.2Hz
C
Repaired by:
31
Block
11
Detailed Code
C : Corrected by customer H : Corrected by dealer E : Corrected by service engineer
Refer to page 8. Indicates the appropriate Self-diagnosis Code Table. step to be taken. E.g. 31 ....Reload the tape. 32 ....Turn on power again.
--7--
3.
Repaired by:
SELF-DIAGNOSIS CODE TABLE
Self-diagnosis Code Block Detailed Function Code 2 2 2 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 1 2 1 1 1 1 1 1 1 1 1 1 1 1 2 2 2 2 2 2 2 2 0 0 0 1 1 2 2 2 2 2 3 4 4 1 1 2 2 2 2 2 3 4 4 0 0 0 0 1 0 1 2 3 4 0 0 2 0 1 0 1 2 3 4 0 0 2 Symptom/State Correction
C C C C C C C C C C C C C C C C C C C C C C C
Non-standard battery is used. Condensation. Video head is dirty. LOAD direction. Loading does not complete within specified time UNLOAD direction. Loading does not complete within specified time T reel side tape slacking when unloading. Winding S reel fault when counting the rest of tape. T reel fault. S reel fault. T reel fault. FG fault when starting capstan. FG fault when starting drum. FG fault during normal drum operations. LOAD direction loading motor timeout. UNLOAD direction loading motor time-out. T reel side tape slacking when unloading. Winding S reel fault when counting the rest of tape. T reel fault. S reel fault. T reel fault. FG fault when starting capstan. FG fault when starting drum FG fault during normal drum operations Difficult to adjust focus (Cannot initialize focus.)
Use the info LITHIUM battery. Remove the cassette, and insert it again after one hour. Clean with the optional cleaning cassette. Load the tape again, and perform operations from the beginning. Load the tape again, and perform operations from the beginning. Load the tape again, and perform operations from the beginning. Load the tape again, and perform operations from the beginning. Load the tape again, and perform operations from the beginning. Load the tape again, and perform operations from the beginning. Load the tape again, and perform operations from the beginning. Load the tape again, and perform operations from the beginning. Load the tape again, and perform operations from the beginning. Load the tape again, and perform operations from the beginning. Remove the battery or power cable, connect, and perform operations from the beginning. Remove the battery or power cable, connect, and perform operations from the beginning. Remove the battery or power cable, connect, and perform operations from the beginning. Remove the battery or power cable, connect, and perform operations from the beginning. Remove the battery or power cable, connect, and perform operations from the beginning. Remove the battery or power cable, connect, and perform operations from the beginning. Remove the battery or power cable, connect, and perform operations from the beginning. Remove the battery or power cable, connect, and perform operations from the beginning. Remove the battery or power cable, connect, and perform operations from the beginning. Remove the battery or power cable, connect, and perform operations from the beginning. Inspect the lens block focus reset sensor (Pin 7 of CN201 of VC220 board) when focusing is performed when the control dial is rotated in the focus manual mode, and the focus motor drive circuit (IC503 of VC-220 board) when the focusing is not performed. Inspect the lens block zoom reset sensor (Pin @º of CN201 of VC220 board) when zooming is performed when the zoom lens is operated and the zoom motor drive circuit (IC503 of VC-220 board) when zooming is not performed. Inspect pitch angular velocity sensor (SE2501 of MR-41 board) peripheral circuits. Inspect yaw angular velocity sensor (SE2500 of MR-41 board) peripheral circuits.
E
6
1
0
0
E
6
1
1
0
Zoom operations fault (Cannot initialize zoom lens.) Steadyshot function does not work well. (With pitch angular velocity sensor output stopped.) Steadyshot function does not work well. (With yaw angular velocity sensor output stopped.)
E
6
2
0
0
E
6
2
0
1
--8--
SECTION 1 GENERAL
DCR-PC2E/PC3/PC3E
This section is extracted from instruction manual. (DCR-PC3E model)
1-1
1-2
1-3
1-4
1-5
1-6
1-7
1-8
1-9
1-10
1-11
1-12
1-13
1-14
1-15
1-16
1-17
1-18
1-19
1-20
1-21
1-22
1-23
1-24
1-25
1-26
1-27
1-28
1-29
1-30
1-31
1-32
1-33
1-34
1-35
1-36
1-37E
SECTION 2 DISASSEMBLY
The following flow chart shows the disassembly procedure.
DCR-PC2E/PC3/PC3E
Note: The disassembly procedure aims at establishing the "service position" as the primary objective. Refer to the detailed drawings that are shown in the balloons of the respective sub-sections for details of disassembling procedure.
2-1. LCD unit, PD-112 board
LCD service position (Mainly for voltage measurement and check) Service position (Mainly for adjustment)
2-2. Cabinet (R) block assembly
DCR-PC2E/PC3/PC3E
2-3. DD-125, VC-220 boards, EVF block assembly
2-4. MR-41 board, MD block
2-8. Control switch block (FK-4750), Speaker (2.0 CM)
2-5. VF-136, CD-221 boards
Service position (Mainly for voltage measurement and check)
2-6. LCD hinge assembly (Perform the disassembling after steps 1-5 of 2-1 is complete.)
2-7. Attaching harnesses of the LCD hinge assembly
2-1
NOTE: Follow the disassembly procedure in the numerical order given.
2-1. LCD UNIT, PD-112 BOARD
REMOVING THE PD-112 BOARD
4 Back light Cold cathode fluorescent tube 8 Inverter transformer unit 3 Remove the three solderings 7 Remove the six solderings
2 -11 PD oard B
2 LCD cabinet (R) assembly A
1 Two screws (M1.7 × 2.5), lock ace, p2 !TM Screw (M1.7 × 2.5), lock ace, p2 5 TP-112 harness (8P) B
2 LCD unit (24P) 1 Touch panel (TP-4750) (5P) 5 PCB clip
9 PD-112 board
2 -11 P D oard B
4 PT-124 harness (13P) ! PD-112 board/ Inverter transformer unit 6 Two screws (M1.7 × 2.5), lock ace, p2 !¢ Back light Cold cathode fluorescent tube
6 PCB clip
!£ Two claws 9 Panel spacer !¡ LCD unit
!º Touch panel (TP-4750)
7 Panel protection sheet A
3 Two screws (M1.7 × 2.5), lock ace, p2
B 8 LCD cabinet (L) assembly
[LCD SERVICE POSITION (Mainly for voltage measurement and check)]
Adjustment remote commander (RM-95) LANC jack
Touch panel (TP-4750) Base (Use box or the like.)
PT-124 harness (13P) TP-112 harness (8P)
2 -11 P D oard B
LCD unit DK-115 Back light Cold cathode fluorescent tube PD-112 board/ Inverter transformer unit AC adaptor (4.2Vdc) (AC-VF10) (AC-VQ11)
AC IN
2-2
2-2. CABINET (R) BLOCK ASSEMBLY
2 Two screws (+K M2 × 3.5) 3 Accessory shoe 4 NS block assembly 8 Screw (M1.7 × 2.5), lock ace, p2 ! Cabinet (R) block assembly When removing it, be careful not to damage the harnesses, etc. !¢ Two screws (M1.7 × 2.5), lock ace, p2 B A
2 -2 VCard Bo A B
0
C !º Jack ornamental plate 9 Two screws (M1.7 × 2.5), lock ace, p2 C !TM Screw (M1.7 × 2.5), lock ace, p2
!£ Push the eject knob in the direction of the arrow, and open the cassette lid.
!¡ Screw (M1.7 × 2.5), lock ace, p2 6 LI-58 harness (2P) 1 Battery terminal cover 7 Tripod screw Two lithium secondary batteries, FP-36 flexible board 5 Two screws (+K M2 × 3.5)
[SERVICE POSITION (Mainly for adjustment)]
Adjustment remote commander (RM-95) CPC-6 terminal board jig (J-6082-371-A)
REMOVING THE LITHIUM BATTERY
CPC-6 flexible jig (J-6082-370-A) Remove the two solderings Lithium battery
Tripod screw FP-36 flexible board (Attached with tripod screw.) DK-115 LI-58 harness (2P) Tripod screw Two lithium secondary batteries, FP-36 flexible board
AC adaptor (4.2Vdc) (AC-VF10) (AC-VQ11)
AC IN
2-3
2-3. DD-125, VC-220 BOARDS, EVF BLOCK ASSEMBLY
2 TP-112 harness (10P) 0 1 PT-124 harness (13P) 4 Cabinet (R) block assembly
2 -2 VCard Bo A B
B
A
REMOVING THE MICROPHONE UNIT
3 TP-112 harness (2P) 4 Microphone case assembly 5 Microphone unit 3 Microphone gel sheet 2 Microphone retainer plate 1 Tapping screw (+K B2) !¢ Microphone case assembly, Microphone unit !TM Flexible board (from lens block) (27P) @º EVF block assembly !ª Screw (M1.7 × 2.5), lock ace, p2 ! VF-136 board (20P) !§ CD-221 board (20P)
!· Screw (M1.7 × 2.5), lock ace, p2
REMOVING THE TP-38 BOARD
TB-38 board
Remove the three solderings
!¶ VC-220 board
2 -2 VCard o B 0
Batt plate
C C !º MR-41 board (100P)
DD-125 Board DD-125
!£ Two screws (M1.7 × 2.5), lock ace, p2 6
!¡ Control switch block (FK-4750) (27P)
5 Two claws
9 DD-125 board 8 Two screws (M1.7 × 2.5), lock ace, p2
7 Two screws (M1.7 × 2.5), lock ace, p2
2-4
2-4. MR-41 BOARD, MD BLOCK
4 Cabinet (L) block assembly 1 Screw (M1.7 × 2.5), lock ace, p2
3 2 Screw (M1.7 × 2.5), lock ace, p2 7 MD block MD frame, Cassette compartment cover assembly
The cabinet (L) when viewed from the bottom
5 Two screws (M1.7 × 2.5), lock ace, p2
MR-41
6 MR-41 board
REMOVING THE MD BLOCK
1 Two special head screws (M1.7 × 3.5) 2 Cassette compartment cover assembly 7 FP-586 flexible board (4P) !¡ MD block
4 FP-91 flexible board (6P) 9 Three step screws
MR-41
6 Two screws (M1.7 × 2.5), lock ace, p2
8 MR-41 board 3 Flexible board (from drum motor)(10P) 5 FP-92 flexible board (51P)
!º MD frame Be careful that the FP-91 flexible board must not be caught when removing it.
2-5
2-5. VF-136, CD-221 BOARDS
5 Remove in the direction of the arrow B while pushing the two claws A inside. Note Be careful not to damage the flexible when pushing out. A
REMOVING THE VF LENS ASSEMBLY
2 Screw (M1.7) 3 VF lens assembly 4 2 Claw
4 VF regulation ring 1 Screw (M1.7 × 3), lock ace, p2
B 1 Two screws (M1.7)
5 Two claws 6 VF window retainer 7 VF window 8 VF cushion
3
9 VF sleeve assembly
REMOVING THE VF-136 BOARD
2 LCD (LCX024AK-J) (DCR-PC2E) (LCX027AK-J) (DCR-PC3/PC3E) 8 BL bracket
7 VF spacer (B) 6 VF-136 board 3 VF spacer (A) 1 Four claws c
5 Light guide plate block Remove by sliding in the direction of the arrow c. 4 Light guide plate block (6P)
REMOVING THE CD-221 BOARD
3 CD frame 6 Seal rubber (W) 5 Optical filter block 4 Lens device (LSV-651A) 2 Two tapping screws
7 CD-221 board
1 Tapping screw (M1.7 × 4)
2-6
[SERVICE POSITION (Mainly for voltage measurement and check)]
Adjustment remote commander (RM-95) LI-58 harness (2P) MD block DD-125 board AC adaptor (4.2Vdc) (AC-VF10) (AC-VQ11) DK-115 Base Support the VC-220 board and the DD-125 board using box or the like. MR-41 board Control switch block (FK-4750) (27P) MR-41 board (100P) TP-112 harness (10P) PT-124 harness (13P) Cabinet (L) block assembly (Control switch block) (FK-4750)
AC IN
1 -4 R M
Cabinet (R) block assembly
0 -22 VC oard B
Base Support the cabinet (R) block assembly using box or the like. VF-136 board (20P)
VC-220 board
Flexible board (from lens block)(27P)
CD-221 board (20P) EVF (VF-136 board) Base (Use box or the like.) Lens block (CD-221 board)
CPC-6 flexible jig (J-6082-370-A) CPC-6 terminal board jig (J-6082-371-A)
2-6. LCD HINGE ASSEMBLY
!¡ Remove the two solderings 4 Two screws (M1.7 × 2.5), lock ace, p2 7 Remove the two solderings 6 Screw (M1.7 × 2.5), lock ace, p2 1 Two tapping screws 8 PO-4 board 9 SW clip !TM PR-32 board !º PR insulating sheet !¢ PT-124 harness (13P) !£ TP-112 harness (10P) 2 Hinge cover (rear) 5
(M1.7 × 5)
! LCD hinge assembly
3 Hinge cover (front)
2-7
2-7. ATTACHING HARNESSES OF THE LCD HINGE ASSEMBLY
1
SW clip PR-32 board PR insulating sheet PO-4 board PT-124 harness PT-124 harness TP-112 harness (13P) (8P) Bend one of the two harnesses at its connector. TP-112 harness LCD hinge assembly Screw (M1.7 × 2.5), lock ace, p2
2
3
Then bend the harness so that it is laid along with the connector.
4
Route the harness.
B A
Route the LCD harness (TP-112) through the hole A toward the center, then route it through the center hole B.
5
2 PR-32 board Attach the PR-32 board with SW clip. Place the PR-32 board in the direction that the solder-escape is directed to soldering.
6
Red
3 Solder here.
Gray
1 PO-4 board 1 PR insulating sheet (Attach it on SW.) 3 SW clip 2 Screw (M1.7 × 2.5), lock ace, p2
Attach the PO-4 board with screw (M1.7 × 2.5). Solder the gray and black wires (TP-112 harness) to the positions as shown.
7 Route the red and white wires (TP-112 harness) through
the hole A as shown and solder them to the PR-32 board. Solder here.
8 Adhere the gray and black wires (TP-112 harness)
as shown with adhesive tape (HIMERON).
Tape (HIMERON)
A
Black White PR-32 board
2-8
2-8. CONTROL SWITCH BLOCK (FK-4750), SPEAKER (2.0 CM)
2 SP retainer plate 1 Two screws (M1.7 × 2.5), lock ace, p2 3 Screw (M1.7 × 2.5), lock ace, p2
!¡ Screw (M2)
9 Remove the two solderings
4 Screw (M1.7 × 2.5), lock ace, p2
Control switch block (FK-4750)
!º Speaker (2.0 CM)
8 Slant the block in the direction of the arrow A, then remove the block in the direction of the arrow B.
B A
7 Screw (M1.7 × 2.5), lock ace, p2 5 Three spacer (C) 6 Peel off the area shown by shading.
Be careful that the flexible must not be caught.
!£ Screw (M1.7 × 2.5) @º Jack fixed plate @ Cabinet (G) assembly @¡ Open the HP jack cover. !· Remove the cabinet (G) assembly from the cabinet (L) block assembly in the arrow direction. Be careful not to damage the control switch block's (FK-4750) flexible.
!¶ Claw
C
!TM Three screws (M1.7 × 2.5) D
! Two screws (M1.7 × 2.5)
!¢ Two screws (M1.7 × 2.5) @£ Two tapping screws (M1.7 × 5)
!§ Tapping screw (M1.7 × 5) C
D @¢ Peel off the area shown by shading.
@TM Tapping screw (M1.7 × 4)
!ª Remove the control switch block that is attached to the cabinet (R), from the cabinet (R). Be careful that the flexible must not be caught.
@§ Control switch block (FK-4750)
2-9
2-9. CIRCUIT BOARDS LOCATION
VF-136 (BACK-LIGHT DRIVE) CD-221 (CCD IMAGER)
PD-112 RGB DECODER, TIMING GENERATOR PR-32 (PANEL REVERSE) INVERTER TRANSFORMER UNIT
PO-4 (PANEL OPEN)
MR-41 DRUM/CAPSTAN MOTOR DRIVE, REC/PB HEAD AMP
VC-220 CAMERA CONTROL, HONEY, LINE OUT, VFD-CPS, SFD, LIP, TFD-CSP, EVF DRIVER, AUDIO PROCESSOR, MECHA SP CONTROL, CME HI CONTROL TB-38 (BATTERY TERMINAL)
DD-125 (DC/DC CONVERTER)
2-10
2-10.FLEXIBLE BOARDS LOCATION
CONTROL SWITCH BLOCK (FK-4750)
FP-36 (Li BATTERY)
TOUCH PANEL (TP-4750)
(From LENS BLOCK)
FP-586 (From LOADING MOTOR)
(From DRUM MOTOR) (From VIDEO HEAD)
FP-91 (MODE) FP-92 TOP/END SENSOR, TAPE LED
FP-242 (S/T REEL SENSOR)
2-11E
SECTION 3 BLOCK DIAGRAMS
3-1. OVERALL BLOCK DIAGRAM (DCR-PC2E MODEL)
DCR-PC2E/PC3/PC3E
3-1
3-2
3-3
3-4
DCR-PC2E/PC3/PC3E
3-2. OVERALL BLOCK DIAGRAM (DCR-PC3/PC3E MODEL)
3-5
3-6
3-7
3-8
DCR-PC2E/PC3/PC3E
3-3. POWER BLOCK DIAGRAM
3-9
3-10
3-11
3-12E
SECTION 4 PRINTED WIRING BOARDS AND SCHEMATIC DIAGRAMS
4-1. FRAME SCHEMATIC DIAGRAM
DCR-PC2E/PC3/PC3E
DCR-PC2E/PC3/PC3E
4-1
4-2
4-3
FRAME SCHEMATIC DIAGRAM
DCR-PC2E/PC3/PC3E
4-2. PRINTED WIRING BOARDS AND SCHEMATIC DIAGRAMS
THIS NOTE IS COMMON FOR WIRING BOARDS AND SCHEMATIC DIAGRAMS (In addition to this, the necessary note is printed in each block)
(For printed wiring boards) · b: Pattern from the side which enables seeing. (The other layers' patterns are not indicated.) · Through hole is omitted. · Circled numbers refer to waveforms. · There are few cases that the par t printed on diagram isn't mounted in this model. · Chip parts. Transistor Diode
C 65 4 45 6 4 5 1 2 3 3 3
CD-221 (CCD IMAGER) PRINTED WIRING BOARD
-- Ref. No. CD-221 Board; 4,000 Series -- CD-221 BOARD
C450 C451 C453 C455 C461 C465 C468 E-5 E-5 D-5 E-6 E-5 E-6 B-6
(Measuring conditions voltage and waveform)
· Voltages and waveforms are measured between the measurement points and ground when camera shoots color bar chart of pattern box. They are reference values and reference waveforms. (VOM of DC 10 M input impedance is used.). · Voltage values change depending upon input impedance of VOM used.) 1. Connection
CN451 D-1 IC450 L450 Q450 R450 R451 R454 R464 R466 R467 F-5 E-5 E-6 D-5 D-5 E-6 D-6 D-5 D-5
Pattern box
B E 12 3 32 1 32 1 54 3 2 1 2 1 2 1
(For schematic diagrams) · All capacitors are in mF unless otherwise noted. pF : m mF. 50V or less are not indicated except for electrolytics and tantalums. · Chip resistors are 1/10W unless otherwise noted. kW=1000W, MW=1000kW. · Caution when replacing chip parts. New parts must be attached after removal of chip. Be careful not to heat the minus side of tantalum capacitor, Because it is damaged by the heat. · Some chip part will be indicated as follows. Example C541 L452 22U 10UH TA A 2520
1.5 m
Front of the lens
For printed wiring boards · This board is six-layer print board. However, the patterns of layers two to five have not been included in the diagram. · Chip parts Transistor
C
Kinds of capacitor Temperature characteristics External dimensions (mm)
· Constants of resistors, capacitors, ICs and etc with XX indicate that they are not used. In such cases, the unused circuits may be indicated. · All variable and adjustable resistors have characteristic curve B, unless otherwise noted. · Signal name XEDIT EDIT PB/XREC PB/REC · 2 : non flammable resistor · 1 : fusible resistor · C : panel designation · A : B+ Line · B : B Line ·J : IN/OUT direction of (+,) B LINE. · C : adjustment for repair. · Circled numbers refer to waveforms.
Note : The components identified by mark ! or dotted line with mark ! are critical for safety. Replace only with part number specified. Note : Les composants identifiés par une marque ! sont critiques pour la sécurité. Ne les remplacer que par une pièce portant le numéro spécifié.
2. Adjust the distance so that the output waveform of Fig. a and the Fig. b can be obtain.
Yellow
H
B
E
White Magenta Red Blue
Cyan Green
There are few cases that the part printed on this diagram isn't mounted in this model.
VF-136 (BACK-LIGHT DRIVE) CD-221 (CCD IMAGER)
A B
A=B
B A
Fig. a (Video output terminal output waveform)
PR-32 (PANEL REVERSE)
PD-112 RGB DECODER, TIMING GENERATOR
Yellow Cyan Green White Magenta Red Blue
Electron beam scanned frame CRT picture frame
PO-4 (PANEL OPEN)
INVERTER TRANSFORMER UNIT
CD-221 BOARD
Fig.b (Picture on monitor TV)
When indicating parts by reference number, pleas include the board name.
CAMERA REC
1 IC450 1,2
2 IC450 3,4
3 IC450 !º
4 IC450 !¡,!TM
5 IC450 !£
6 Q450 E
6.8Vp-p H H
6.8Vp-p 56nsec
2.7Vp-p
56nsec
3Vp-p
H
17Vp-p H 0.96Vp-p
4-5
CCD IMAGER
CD-221
4-6
4-7
4-8
DCR-PC2E/PC3/PC3E
For schematic diagram · Refer to page 4-37 for printed wiring board.
VC-220 BOARD (1/9)
CAMERA REC
1 IC203 @§,@¶
8 IC202 @,@§
7.0Vp-p H H 0.96Vp-p
2 IC203 2-!¡
9 IC202 @·,#¡
2.7Vp-p 56nsec
7Vp-p H
3 IC203 !§
CAMERA REC/PB
!º IC202 #£
H 18MHz 2.7Vp-p
19Vp-p
4 IC202 5
CAMERA REC/PB
!¡ IC206 $º (X202)
CAMERA REC/PB
36.0MHz
3.0Vp-p
20.0MHz
2.6Vp-p
5 IC202 !TM
CAMERA REC/PB
18.0MHz
2.7Vp-p
6 IC202 !·
2.7Vp-p 56nsec
7 IC202 @¡,@TM
2.8Vp-p 56nsec
4-9
4-10
4-11
CAMERA CONTROL
VC-220 (1/9)
DCR-PC2E/PC3/PC3E
For schematic diagram · Refer to page 4-37 for printed wiring board.
VC-220 BOARD (2/9)
CAMERA REC/PB
!TM IC758 !£
20MHz
3.2Vp-p
DS CONTROL · HONEY
VC-220 (2/9)
4-12
4-13
4-14
DCR-PC2E/PC3/PC3E
For schematic diagram · Refer to page 4-37 for printed wiring board.
VC-220 BOARD (3/9)
CAMERA REC/PB
!£ IC1200 @
LINE REC
(C1200)
@º IC1402 !TM
0.44Vp-p
H
H
1.4Vp-p
!¢ IC1200 #£
LINE REC
(C1202)
@¡ IC1402 !§
0.37Vp-p
H
H
1.7Vp-p
! IC1200 #¢
LINE REC
(C1207)
0.46Vp-p
H
!§ IC1200 $£
LINE REC
(R1270)
40.5MHz
4Vp-p
!¶ IC1402 @
H
0.45Vp-p
!· IC1402 @ª
0.34Vp-p H
!ª IC1402 7
H
1.9Vp-p
4-15
4-16
4-17
LINE OUT AMP, BBI
VC-220 (3/9)
DCR-PC2E/PC3/PC3E
For schematic diagram · Refer to page 4-37 for printed wiring board.
VC-220 BOARD (4/9)
CAMERA REC/PB
@TM IC1502 8
13.5MHz
3.0Vp-p
@£ Q1500 E
H
0.22Vp-p
@¢ Q1501 E
0.2Vp-p H
@ Q1502 E
H
0.26Vp-p
@§ Q1503 E
H
0.32Vp-p
@¶ Q1504 E
H
0.4Vp-p
VFD-CPS
VC-220 (4/9)
4-18
4-19
4-20
DCR-PC2E/PC3/PC3E
For schematic diagram · Refer to page 4-37 for printed wiring board.
VC-220 BOARD (5/9)
CAMERA REC/PB
@· IC1600 !¢
(X1600,C1606)
24.576MHz
1.8Vp-p
@ª IC1600 #º (L1601)
30MHz
1.5Vp-p
4-21
4-22
4-23
SFD, LIP, TFD-CSP
VC-220 (5/9)
DCR-PC2E/PC3/PC3E
For schematic diagram · Refer to page 4-37 for printed wiring board.
VC-220 BOARD (6/9)
CAMERA REC/PB
#º IC5000 8
#§ IC5002 !·
0.26Vp-p H 16.6msec 2.7Vp-p
#¡ IC5000 9
#¶ IC5002 @º,@¡
0.2Vp-p H 2H
2.7Vp-p
#TM IC5000 !º
#· IC5002 @TM
0.22Vp-p H H
2.7Vp-p
#£ IC5000 @º
#ª IC5002 @£,@¢
7Vp-p 2H
2.75MHz
2.7Vp-p
#¢ IC5000 @TM
$º IC5002 $¡
7Vp-p 2H
16.1MHz
2.8Vp-p
# IC5000 @¢
7Vp-p 2H
EVF DRIVER
VC-220 (6/9)
4-24
4-25
4-26
DCR-PC2E/PC3/PC3E
For schematic diagram · Refer to page 4-37 for printed wiring board.
4-27
4-28
AUDIO PROCESSOR
VC-220 (7/9)
DCR-PC2E/PC3/PC3E
For schematic diagram · Refer to page 4-37 for printed wiring board. · Refer to page 4-34 for waveforms.
MECHA SP CONTROL
VC-220 (8/9)
4-29
4-30
DCR-PC2E/PC3/PC3E
For schematic diagram · Refer to page 4-37 for printed wiring board.
PR-32 (PANEL REVERSE) , PO-4 (PANEL OPEN) PRINTED WIRING BOARDS
-- Ref. No. PR-32, PO-4 Boards; 10,000 Series --
For printed wiring boards · This board is six-layer print board. However, the patterns of layers two to six have not been included in the diagram.
VF-136 (BACK-LIGHT DRIVE) CD-221 (CCD IMAGER)
There are few cases that the part printed on this diagram isn't mounted in this model.
PD-112 RGB DECODER, TIMING GENERATOR PR-32 (PANEL REVERSE) INVERTER TRANSFORMER UNIT
PO-4 (PANEL OPEN)
VC-220 BOARD (8/9)
CAMERA REC/PB
VC-220 BOARD (9/9)
CAMERA REC/PB
$¡ IC2401 2
(X2400,C2403)
$TM IC2204 $º (X2200)
$£ IC2204 %£
(X2201, R2262)
20.0MHz
2.2Vp-p
20.0MHz
2.8Vp-p 32.768kHz
3.0Vp-p
4-31
4-32
4-33
CHE HI CONTROL
VC-220 (9/9)
/ PANEL REVERSE, PANEL OPEN
PR-32, PO-4
DCR-PC2E/PC3/PC3E
DCR-PC2E/PC3/PC3E
VC-220 (CAMERA CONTROL, HONEY, LINE OUT, VFD-CPS, SFD, LIP, TFD-CSP, EVF DRIVER, AUDIO PROCESSOR, MECHA SP CONTROL, CME HI CONTROL) PRINTED WIRING BOARD -- Ref. No. VC-220 Board; 10,000 Series -- VC-220 BOARD (SIDE A)
C202 C203 C205 C206 C207 C210 C211 C212 C214 C215 C216 C219 C221 C230 C750 C754 C755 C756 C757 C762 C773 C774 C775 C776 C1200 C1201 C1202 C1203 C1204 C1205 C1206 C1207 C1208 C1209 C1210 C1211 C1212 C1213 C1214 C1215 C1216 C1217 C1218 C1219 C1220 C1221 C1223 C1224 C1225 C1226 C1227 C1228 C1229 C1230 C1231 C1232 C1233 C1234 C1235 C1503 C1505 C1506 C1507 C1512 C1513 C1600 E-7 E-7 D-6 D-6 D-6 E-7 E-7 E-11 E-11 E-11 D-7 D-7 D-7 D-7 A-6 B-6 B-7 B-7 B-6 B-7 B-6 B-7 B-7 B-6 B-5 B-5 B-5 B-5 B-5 B-5 A-6 B-5 A-6 B-6 B-6 A-6 A-5 A-6 A-6 A-5 A-5 A-6 A-6 B-5 B-5 A-6 B-6 B-6 B-5 A-5 A-5 B-6 B-6 B-6 A-6 A-5 A-5 B-5 B-5 D-6 D-7 D-6 D-6 D-7 C-7 C-5 C1601 C1602 C1603 C1604 C1606 C1607 C1608 C1609 C1611 C1612 C1613 C1614 C1615 C1616 C1617 C1618 C1619 C1620 C1621 C1623 C1624 C2208 C2212 C2215 C2220 C2221 C2222 C2223 C2226 C2227 C2232 C2233 C2234 C2400 C2402 C2403 C2405 C2408 C2410 C5000 C5001 C5002 C5003 C5004 C5005 C5006 C5007 C5009 C5010 C5011 C5013 C5014 C5015 C5016 C5017 C5018 C5019 C5020 C5021 C5022 C5023 C5024 C5025 C5029 C5030 B-5 C-5 C-5 C-5 C-5 C-5 D-5 D-5 D-5 D-5 E-6 D-5 D-5 D-5 B-5 D-5 D-5 B-5 C-5 D-5 D-5 E-2 D-2 D-2 E-1 E-1 E-2 E-2 E-2 C-1 D-2 C-2 D-2 E-2 E-3 E-3 D-3 C-3 D-3 C-8 C-8 C-8 C-8 C-8 C-8 C-8 C-8 D-8 D-8 D-8 C-8 C-8 B-8 B-8 A-7 A-8 A-7 B-8 A-8 B-8 B-8 A-8 A-8 D-8 B-8 CN201 CN1600 CN2904 CN2908 CN2909 CN2910 CN2911 CN2915 D202 D1200 D1201 D1600 D2211 D2901 D2902 D5000 FB207 IC202 IC751 IC753 IC754 IC755 IC760 IC761 IC1200 IC1501 IC1502 IC1600 IC1601 IC1602 IC2204 IC2401 IC2404 IC5000 IC5001 IC5002 IC5003 L206 L751 L1200 L1201 L1202 L1203 L1204 L1205 L1500 L1501 L1502 L1601 L1602 L1603 L1605 L1606 L1609 L2201 L2400 L5000 L5001 L5003 L5004 L5006 D-8 F-3 A-8 E-5 D-4 E-2 E-8 E-7 D-7 A-5 B-5 B-5 E-1 E-2 E-2 A-8 D-7 D-7 B-7 A-7 A-11 C-7 B-7 A-7 A-5 C-6 C-7 C-5 D-6 D-4 D-2 D-3 D-3 C-8 B-8 B-8 A-8 E-7 B-6 B-5 B-5 A-5 B-6 B-5 A-5 C-7 C-7 D-6 B-5 D-5 C-5 C-5 D-5 D-5 D-3 C-3 B-8 D-8 B-8 B-8 B-8 Q752 Q753 Q754 Q757 Q1200 Q1201 Q1202 Q1203 Q1206 Q1207 Q1208 Q1209 Q1500 Q1501 Q1502 Q1503 Q1504 Q2213 Q2214 Q2216 Q2222 Q2901 Q2904 Q2914 Q2915 R202 R203 R206 R216 R216 R217 R221 R702 R703 R704 R705 R753 R754 R756 R757 R758 R759 R761 R762 R763 R764 R765 R766 R767 R768 R769 R770 R771 R772 R773 R774 R775 R776 R777 R778 R779 R780 R781 R782 R783 B-7 B-6 A-6 B-7 A-6 B-6 B-5 B-6 B-6 A-6 B-6 B-6 D-6 D-6 D-7 D-7 D-7 E-2 E-2 D-2 D-2 A-8 E-6 E-6 E-6 E-7 E-7 D-6 D-8 D-8 D-7 D-7 B-7 C-7 C-7 B-7 B-7 B-7 B-7 B-7 B-7 B-7 C-8 B-7 C-8 B-7 A-6 A-7 A-7 A-7 A-7 A-7 A-7 A-7 A-7 A-7 A-7 A-7 A-6 A-6 A-6 A-6 A-6 A-6 A-6 R785 R786 R795 R799 R801 R816 R817 R821 R1202 R1203 R1204 R1205 R1206 R1207 R1208 R1209 R1210 R1211 R1212 R1213 R1214 R1215 R1216 R1217 R1218 R1219 R1266 R1267 R1268 R1269 R1270 R1271 R1272 R1507 R1508 R1509 R1510 R1511 R1512 R1513 R1514 R1515 R1516 R1517 R1518 R1519 R1521 R1522 R1618 R1619 R1620 R1621 R1622 R1623 R1624 R1625 R1626 R1628 R1629 R1630 R1637 R1638 R1648 R1689 R1694 R1695 B-6 C-7 B-6 B-7 B-7 B-6 B-6 A-6 A-5 A-5 B-6 A-6 B-6 B-6 B-5 B-5 B-6 B-6 B-5 B-6 B-6 B-6 B-6 A-6 B-6 A-6 A-5 B-5 A-5 A-5 B-5 B-5 D-6 D-6 D-7 D-6 D-6 D-7 D-6 D-6 D-7 D-7 D-7 D-7 C-7 D-7 D-6 C-5 C-5 C-5 C-5 C-5 C-5 C-6 C-6 C-5 D-6 D-5 D-5 D-5 D-5 D-4 C-5 D-5 D-5 R1696 R1697 R1698 R1699 R2207 R2208 R2212 R2221 R2222 R2223 R2224 R2225 R2226 R2229 R2230 R2231 R2235 R2236 R2237 R2239 R2240 R2241 R2242 R2243 R2244 R2245 R2246 R2247 R2248 R2249 R2250 R2251 R2252 R2254 R2255 R2256 R2257 R2258 R2259 R2260 R2262 R2263 R2264 R2265 R2266 R2267 R2268 R2269 R2270 R2271 R2272 R2273 R2274 R2275 R2277 R2278 R2279 R2280 R2281 R2282 R2283 R2284 R2285 R2286 R2287 R2288 D-5 D-5 D-4 D-4 E-2 E-2 C-2 E-1 E-1 E-1 E-1 E-1 E-1 E-1 E-1 E-1 D-1 D-2 E-2 E-2 D-1 D-1 D-1 D-2 D-2 C-1 E-1 D-1 E-1 E-1 E-1 E-1 E-1 E-2 E-2 E-1 C-1 E-2 E-2 E-2 D-2 E-2 E-2 D-2 D-2 D-2 D-2 E-2 D-2 E-2 E-2 D-2 D-2 D-2 E-1 E-1 E-1 D-1 D-1 D-1 D-1 E-1 D-1 E-1 E-1 E-1 R2289 R2290 R2291 R2292 R2293 R2295 R2296 R2297 R2300 R2301 R2401 R2403 R2405 R2406 R2407 R2408 R2410 R2413 R2415 R2416 R2417 R2418 R2419 R2420 R2421 R2422 R2423 R2424 R2428 R2429 R2430 R2432 R2433 R2434 R2436 R2439 R2440 R2441 R2442 R2443 R2445 R2908 R2929 R2930 R2931 R2932 R2933 R2935 R2936 R2937 R5001 R5002 R5003 R5005 R5006 R5007 R5008 R5009 R5010 R5011 R5012 R5013 R5014 R5015 R5018 R5020 E-1 E-1 E-2 E-2 E-2 D-2 D-2 D-2 E-2 C-2 E-2 C-3 E-3 E-3 E-2 E-2 E-2 E-3 E-2 E-2 E-2 E-2 E-2 E-2 E-2 E-2 E-2 E-2 D-3 D-3 D-3 D-3 C-3 D-3 D-3 D-3 D-3 D-3 D-3 D-3 E-2 E-5 D-6 E-7 E-1 E-7 E-6 A-8 E-2 A-5 C-8 C-8 C-8 C-8 C-8 C-8 C-8 C-7 C-7 C-7 C-7 C-7 C-7 C-7 C-8 C-7 R5021 R5023 R5024 R5025 R5026 R5027 R5028 R5029 R5030 R5031 R5032 R5033 R5035 R5036 R5037 R5039 R5040 R5041 X201 X750 X1200 X1600 X2200 X2201 X2400 C-7 C-8 A-8 A-8 A-8 A-7 A-7 B-8 B-7 A-8 A-8 A-8 C-7 A-8 B-8 C-8 A-8 A-8 D-7 A-7 A-5 C-5 C-2 C-2 E-3
DV OUT DV IN/OUT
PC2E/PC3E: AEP, UK MODEL PC3/PC3E: EXCEPT AEP, UK MODEL
For printed wiring boards · This board is eight-layer print board. However, the patterns of layers two to seven have not been included in the diagram. · Chip parts Transistor
C 65 4
MR-41 DRUM/CAPSTAN MOTOR DRIVE, REC/PB HEAD AMP
VC-220 CAMERA CONTROL, HONEY, LINE OUT, VFD-CPS, SFD, LIP, TFD-CSP, EVF DRIVER, AUDIO PROCESSOR, MECHA SP CONTROL, CME HI CONTROL TB-38 (BATTERY TERMINAL)
B
E
12 3
There are few cases that the part printed on this diagram isn't mounted in this model.
DD-125 (DC/DC CONVERTER)
CAMERA CONTROL, HONEY, LINE OUT, VFD-CPS, SFD, LIP, TFD-CSP, EVF DRIVER, AUDIO PROCESSOR, MECHA SP CONTROL, CME HI CONTROL
VC-220
4-37
4-38
DCR-PC2E/PC3/PC3E
VC-220 BOARD (SIDE B)
C204 C217 C218 C220 C222 C223 C224 C225 C226 C227 C228 C229 C231 C232 C233 C234 C235 C236 C237 C238 C239 C240 C241 C242 C243 C244 C245 C246 C247 C248 C255 C256 C257 C502 C504 C507 C508 C509 C510 C511 C512 C513 C514 C515 C516 C518 C519 C520 C521 C522 C523 C753 C759 C760 C761 C763 C764 C766 C770 C771 C772 C1401 C1402 C1403 C1404 C1405 C-11 E-11 E-11 E-11 E-10 E-10 E-10 D-10 D-10 D-10 D-10 D-11 B-11 B-10 C-11 C-11 C-11 B-11 C-11 E-10 A-11 B-10 B-10 B-11 B-11 B-11 B-10 B-10 B-10 C-11 D-11 B-11 E-11 C-10 C-10 D-10 D-10 C-10 B-10 C-10 B-10 C-10 C-10 C-10 C-10 D-11 C-10 D-11 C-10 D-10 C-10 B-11 B-11 A-11 A-11 B-13 A-13 A-13 B-11 B-11 B-12 B-13 B-13 D-13 C-13 C-13 C1406 C1409 C1418 C1422 C1423 C1433 C1434 C1436 C1438 C1439 C1449 C1452 C1453 C2001 C2002 C2003 C2004 C2005 C2006 C2007 C2008 C2009 C2010 C2011 C2012 C2013 C2014 C2015 C2016 C2017 C2018 C2019 C2020 C2021 C2022 C2023 C2026 C2028 C2030 C2032 C2035 C2038 C2040 C2041 C2042 C2044 C2046 C2049 C2050 C2051 C2052 C2053 C2053 C2054 C2055 C2056 C2057 C2058 C2059 C2060 C2061 C2062 C2063 C2064 C2065 C2069 B-13 B-13 C-13 D-13 C-13 D-14 F-13 C-13 D-14 C-13 B-13 D-13 D-14 E-12 E-12 E-12 E-12 E-12 E-12 C-12 E-12 E-12 C-12 E-12 E-12 E-12 E-12 D-13 D-13 E-13 D-12 E-12 E-12 D-12 D-13 D-13 E-12 D-13 C-12 E-12 E-13 C-12 D-13 D-12 C-12 D-13 C-12 D-12 D-12 D-12 D-12 D-11 D-11 D-12 D-11 C-12 C-11 C-11 C-12 C-11 C-12 C-11 D-11 C-11 C-12 D-12 C2070 C2071 C2072 C2073 C2074 C2075 C2076 C2077 C2078 C2079 C2080 C2081 C2082 C2083 C2084 C2085 C2206 C2207 C2210 C2211 C2213 C2224 C2237 C2238 C2900 C2901 C2902 C2902 C2903 C2904 C2905 C5027 C5028 D-12 D-12 D-13 D-12 E-13 E-13 E-12 D-11 D-11 D-12 D-12 C-12 C-12 D-11 D-12 E-13 D-15 D-15 D-14 E-14 D-14 D-14 D-14 D-14 E-11 D-10 D-10 D-10 D-10 E-10 F-10 D-10 E-10 IC1402 IC1404 IC1405 IC2001 IC2002 IC2003 IC2006 IC2200 IC2201 IC2203 L201 L202 L203 L204 L207 L501 L502 L503 L504 L752 L753 L1400 L2001 L2002 L2003 L2004 L2005 L2900 Q201 Q202 Q205 Q500 Q501 Q502 Q503 Q755 Q756 Q1400 Q1402 Q1403 Q1405 Q1406 Q2001 Q2002 Q2003 Q2010 Q2011 Q2012 Q2017 Q2018 Q2019 Q2201 Q2202 Q2206 Q2211 Q2908 Q2909 Q2912 Q2913 R205 R209 R210 R213 C-13 B-13 B-13 E-12 D-12 C-12 E-13 D-14 D-15 E-15 D-11 B-11 C-10 B-11 B-11 B-10 D-11 C-10 C-10 A-13 B-12 C-12 E-13 D-13 D-11 D-11 D-11 E-11 C-11 C-11 A-10 B-10 B-10 C-10 C-10 C-11 C-12 D-13 E-13 D-13 D-13 D-13 D-13 D-13 E-13 D-13 E-13 E-13 D-12 C-13 D-13 D-14 D-14 D-15 D-14 D-10 D-10 D-10 D-10 A-11 A-10 A-10 A-10 R214 R218 R226 R230 R234 R236 R237 R238 R245 R246 R247 R250 R251 R252 R255 R256 R258 R259 R260 R261 R262 R264 R266 R284 R285 R286 R290 R291 R292 R501 R502 R503 R504 R505 R507 R509 R510 R511 R512 R513 R514 R515 R516 R517 R518 R519 R520 R521 R522 R523 R524 R525 R526 R527 R760 R787 R788 R791 R792 R793 R794 R796 R800 R814 R815 R820 A-10 B-11 C-11 A-10 A-10 A-10 A-10 A-10 A-10 A-11 A-10 A-10 A-11 A-11 A-11 B-10 B-11 B-11 B-10 B-10 B-10 B-10 B-10 C-11 B-11 A-10 A-10 A-10 A-10 B-10 B-10 B-10 B-10 C-10 D-10 D-10 C-10 D-10 D-10 D-10 C-10 D-10 C-10 C-10 C-10 C-10 C-10 C-10 C-10 C-10 C-10 C-10 C-10 A-10 A-12 B-13 B-12 A-12 A-13 C-12 B-13 B-12 B-12 C-12 C-12 B-12 R822 R1400 R1401 R1403 R1404 R1405 R1410 R1418 R1419 R1421 R1425 R1426 R1430 R1432 R1433 R1434 R1438 R1439 R1440 R1445 R1446 R1447 R1496 R1497 R1498 R1499 R2001 R2002 R2005 R2006 R2007 R2008 R2009 R2010 R2011 R2012 R2013 R2014 R2016 R2018 R2019 R2020 R2022 R2026 R2027 R2028 R2029 R2040 R2041 R2042 R2043 R2044 R2045 R2046 R2047 R2048 R2049 R2050 R2051 R2052 R2053 R2054 R2055 R2056 R2058 R2059 C-12 D-14 D-14 D-14 B-13 B-13 D-14 C-12 D-14 D-14 D-14 D-14 D-13 D-14 D-13 D-13 D-14 D-14 D-13 D-14 D-14 D-14 D-13 B-13 C-13 D-14 E-12 E-12 D-13 E-13 C-12 E-13 D-13 C-13 E-12 E-12 E-12 E-12 C-12 D-12 D-11 D-12 C-12 C-12 C-11 C-11 C-12 E-12 E-12 D-13 D-13 E-13 E-13 D-13 D-13 D-13 E-13 E-12 D-12 D-12 D-12 E-13 E-13 E-13 C-12 C-12 R2060 R2061 R2064 R2065 R2066 R2067 R2202 R2203 R2204 R2205 R2206 R2209 R2210 R2211 R2215 R2227 R2232 R2233 R2234 R2302 R2900 R2901 R2902 R2903 R2904 R2905 R2906 R2907 R2910 R2911 R2912 R2913 R2914 R2915 R2916 R2917 R2918 R2919 R2920 R2921 R2922 R2923 R2924 R2925 R2926 R2927 R2928 R2929 R2938 R5016 R5017 R5019 C-12 E-12 D-13 E-13 E-13 E-13 D-14 D-14 D-14 D-15 D-14 D-14 D-15 D-14 D-15 E-14 D-14 E-14 D-15 D-14 D-10 D-10 D-10 D-10 E-10 D-10 D-10 E-10 A-11 A-11 A-11 A-11 B-11 A-11 A-11 A-11 A-11 A-11 A-11 A-11 A-11 A-11 A-11 A-11 B-11 B-11 A-11 A-11 D-10 D-10 D-10 D-10
CN202 E-11 CN2001 E-11 CN5000 E-10 D501 D2001 D2201 D2203 D2206 D2208 D2212 FB203 FB204 FB205 FB206 FB209 FB750 FB751 FB752 IC201 IC203 IC204 IC206 IC207 IC502 IC503 IC756 IC757 IC758 IC759 C-10 E-13 D-14 D-15 D-14 D-15 D-15 C-11 D-11 B-11 C-11 B-11 A-11 A-13 A-12 B-10 D-11 A-10 A-10 C-11 C-10 B-10 A-12 A-13 B-12 B-12
VDR001 E-14 VDR002 E-14 X202 X751 A-10 B-13
4-39
4-40
CAMERA CONTROL, HONEY, LINE OUT, VFD-CPS, SFD, LIP, TFD-CSP, EVF DRIVER, AUDIO PROCESSOR, MECHA SP CONTROL, CME HI CONTROL
VC-220
DCR-PC2E/PC3/PC3E
MR-41 (DRUM/CAPSTAN MOTOR DRIVE, REC/PB HEAD AMP) PRINTED WIRING BOARD
-- Ref. No. MR-41 Board; 10,000 Series -- MR-41 BOARD
C1804 C1805 C1806 C1807 C1809 C1833 C1834 C1837 C1840 C1844 C1845 C1846 C1850 C1852 C1854 C1856 C1860 C1866 C1869 C1875 C1878 C1881 C1884 C1885 C1886 C1887 C1888 C1888 C1889 C1890 C1901 C1903 C1904 C1909 C1910 C1914 C1915 C1933 C2500 C2501 C2507 C2546 C2550 C2551 D-8 C-7 C-1 B-1 D-2 C-2 C-2 C-1 C-2 C-2 D-8 C-1 D-1 D-1 D-1 D-1 D-8 D-8 E-7 E-7 D-2 D-2 D-7 D-8 D-8 E-7 D-2 C-1 D-2 C-2 C-7 D-8 B-8 D-8 C-8 C-8 E-7 C-8 A-3 F-1 A-3 B-7 A-7 B-7 C2552 C2553 C2554 C2555 C2556 C2557 C2558 C2559 C2561 C2562 C2563 C2564 C2565 C2566 C2567 C2569 C2570 C2572 C2573 C2574 C2575 C2576 C2577 C2579 C2582 C2583 C2585 C2586 C2587 C2588 C2589 C2590 C2591 C2592 C2593 C2594 C2595 C2596 C2597 C2598 C2599 C2600 C2601 C2602 B-7 A-7 A-8 A-8 A-8 A-8 A-8 A-8 B-8 A-8 A-8 A-8 A-2 A-2 B-2 C-3 A-2 A-2 A-2 B-2 A-2 B-2 B-2 C-2 A-1 A-1 A-1 A-1 A-1 A-1 B-1 B-7 B-7 C-1 E-8 E-8 E-8 F-8 F-7 D-2 E-1 E-1 F-8 F-8 C2603 C2604 C2605 C2606 C2607 C2608 C2609 C2610 C2611 C2612 CN1810 CN2501 CN2504 CN2505 CN2507 CN2508 D2053 D2500 D2501 D2502 D2504 F2500 IC1814 IC1816 IC1900 IC2500 IC2503 IC2504 IC2505 IC2506 L1803 L1804 L1805 L1808 L1811 L2511 L2512 L2513 L2514 F-8 F-8 F-8 F-8 F-7 F-8 D-1 D-1 D-1 D-2 E-2 B-1 F-7 D-2 A-7 E-5 F-2 A-8 F-1 E-1 E-2 E-2 C-2 D-7 C-8 F-1 B-8 A-2 B-2 F-8 D-8 D-2 D-8 E-8 E-7 B-7 A-1 B-1 B-2 L2515 Q1801 Q2505 Q2506 Q2507 Q2508 Q2509 Q2510 R1826 R1827 R1828 R1829 R1831 R1833 R1834 R1835 R1836 R1837 R1838 R1839 R1840 R1843 R1848 R1852 R1855 R1857 R1859 R1869 R1870 R1871 R1872 R1874 R1909 R1938 R1939 R1940 R1941 R1942 R1943 R1944 R1945 R1946 F-7 C-1 A-8 A-8 B-1 A-7 A-7 E-2 D-1 C-7 D-1 B-8 B-1 C-1 D-7 D-7 D-7 D-7 D-7 D-7 D-1 E-7 D-7 D-7 D-7 D-7 D-7 D-2 D-2 D-2 C-1 D-1 D-8 C-8 B-8 C-8 C-8 C-8 D-8 D-8 B-7 D-8 R1947 R1949 R1950 R1951 R1952 R2500 R2501 R2502 R2505 R2506 R2507 R2508 R2509 R2510 R2511 R2517 R2530 R2531 R2532 R2533 R2534 R2546 R2547 R2549 R2550 R2551 R2552 R2553 R2554 R2556 R2557 R2558 R2559 R2560 R2564 R2565 R2566 R2567 R2568 R2569 R2570 R2571 R2572 R2573 C-7 C-7 C-7 C-7 C-7 F-1 F-1 A-8 A-3 A-3 A-3 A-3 A-8 A-8 A-2 A-2 A-2 A-7 A-7 A-7 A-1 A-8 A-8 B-7 B-7 A-7 A-8 A-8 A-8 B-8 B-8 A-8 B-8 B-8 B-3 B-3 B-8 A-8 A-8 A-2 A-1 B-7 A-2 A-8 R2574 R2575 R2576 R2577 R2578 R2579 R2580 R2581 R2582 R2583 R2585 R2586 R2587 R2588 R2599 R2600 R2601 R2602 R2603 R2604 R2606 R2607 R2608 R2609 R2610 R2611 R2612 R2613 R2614 R2615 R2616 R2617 R2618 R2619 R2620 R2621 R2622 R2623 C-7 B-7 B-7 B-7 A-8 A-2 B-7 B-7 B-1 B-1 A-1 B-1 A-2 A-8 A-7 A-8 A-7 A-8 A-7 A-8 E-8 E-8 E-8 E-8 E-8 E-1 F-8 F-8 F-7 F-7 F-7 F-1 E-1 A-8 F-7 B-3 F-2 F-2
SE2500 D-1 SE2501 E-1
For printed wiring boards · This board is six-layer print board. However, the patterns of layers two to five have not been included in the diagram. · Chip parts Transistor
C
MR-41 DRUM/CAPSTAN MOTOR DRIVE, REC/PB HEAD AMP
VC-220 CAMERA CONTROL, HONEY, LINE OUT, VFD-CPS, SFD, LIP, TFD-CSP, EVF DRIVER, AUDIO PROCESSOR, MECHA SP CONTROL, CME HI CONTROL TB-38 (BATTERY TERMINAL)
B
E
There are few cases that the part printed on this diagram isn't mounted in this model.
DD-125 (DC/DC CONVERTER)
DRUM/CAPSTAN MOTOR DRIVE, REC/PB HEAD AMP
MR-41
4-43
4-44
DCR-PC2E/PC3/PC3E
MR-41 BOARD (1/2)
CAMERA REC/PB
1 IC2503 4
7 IC2503 ^º
2.6Vp-p 6.7msec 1.1msec
2.7Vp-p 900kHz
2 IC2503 @TM,@£,@¢
8 IC2503 ^£
0.1Vp-p 1.1msec 1.1msec
0.2Vp-p 900kHz
3 IC2503 @,@§,@¶
9 IC2504 !¶
2.1Vp-p 1.1msec 0.92msec
2.7Vp-p
4 IC2503 $
!º IC2504 #¡,#£,#¢
2.6Vp-p 0.3sec 82msec
0.6Vp-p
5 IC2503 $·
!¡ IC2505 2,!·,@£
2.7Vp-p 0.78sec 1.1msec
2.1Vp-p
6 IC2503 %¢
2.7Vp-p 3µsec
4-45
4-46
4-47
4-48
DRUM/CAPSTAN MOTOR DRIVE
MR-41 (1/2)
DCR-PC2E/PC3/PC3E
FP-91 (MODE), FP-92 (TOP/END SENSOR, TAPE LED), FP-242 (S/T REEL SENSOR) PRINTED WIRING BOARDS -- Ref. No. FP-91, 92, 242 Flexible Boards; 10,000 Series --
For schematic diagram · Refer to page 4-43 for printed wiring board.
FP-91 FLEXIBLE BOARD
1
FP-92 FLEXIBLE BOARD
CN902
10 1
MR-41 BOARD (2/2) !TM IC1900 !¡,
IC1816 $TM CAMERA REC
S902 MODE SWITCH
1 51 18
2.2Vp-p 25nsec
CN903
!£ IC1816 1,2,6,7
CAMERA REC
3.5Vp-p 6.8msec
Q901 TAPE TOP
!¢ IC1816 @¶ PB
0.4Vp-p
6.8msec
1-673-244-
11
S901 REC PROOF
CN901 (4P)
FP-242 FLEXIBLE BOARD
16 1
R904
H902
R903
A
T5 S- C
1 16
R902
H901
FP242
D901
16
MODE, TOP/END SENSOR, TAPE LED, S/T REEL SENSOR
FP-91, FP-92, FP-242
1-656-247R901
1-656-247- 14
(From LENS BLOCK)
S903 CC DOWN
FP-586 (From LOADING MOTOR)
1-673-245- 11
(From DRUM MOTOR) (From VIDEO HEAD)
16
Q902 TAPE END
FP-91 (MODE) FP-92 TOP/END SENSOR, TAPE LED FP-242 (S/T REEL SENSOR)
/ REC/PB HEAD AMP
MR-41 (2/2)
4-50
4-51
4-52
DCR-PC2E/PC3/PC3E
4-53
4-54
CONTROL SWITCH BLOCK
FK-4750
DCR-PC2E/PC3/PC3E
PD-112 (RGB DECODER, TIMING GENERATOR) PRINTED WIRING BOARD
-- Ref. No. PD-112 Board; 10,000 Series -- PD-112 BOARD
C8001 C8003 C8005 C8006 C8008 C8009 C8010 C8011 C8012 C8013 C8014 C8015 C8016 C8017 C8018 C8019 C8020 C8021 C8022 C8023 C8024 C8025 C8026 C8027 C8100 C8101 C8102 C8103 C8104 C8105 C8200 C8201 C8202 C8203 C8204 C8205 C8206 C8207 C8208 C8209 C8210 C8211 C8212 C8213 C8214 C-1 D-1 D-1 D-1 C-2 D-2 D-2 D-2 D-2 D-1 D-1 C-1 D-1 D-1 D-3 C-2 C-2 C-2 D-2 D-3 C-3 C-3 C-1 B-3 C-3 C-3 C-3 C-3 C-3 C-3 C-1 C-2 C-2 B-2 C-3 C-2 C-2 B-2 C-3 C-3 B-2 B-2 B-2 B-2 B-2 CN8001 CN8002 CN8003 CN8200 CN8201 D8100 D8200 D8201 D8202 IC8001 IC8200 IC8201 IC8202 L8001 L8002 L8100 L8101 L8200 L8201 L8202 Q8000 Q8001 Q8002 Q8003 Q8007 Q8009 Q8010 Q8011 Q8100 Q8101 Q8102 Q8200 Q8201 Q8203 Q8204 R8000 R8001 R8002 R8003 R8004 C-1 B-1 B-3 B-2 D-3 A-3 B-1 C-3 B-2 D-2 B-3 C-2 B-1 C-2 C-3 C-3 C-3 B-2 B-2 B-3 C-1 C-1 C-1 C-2 C-3 C-3 C-3 D-3 A-4 D-3 D-3 A-1 B-1 C-3 A-3 C-1 C-1 C-1 C-1 D-1 R8005 R8006 R8012 R8014 R8015 R8016 R8017 R8018 R8019 R8020 R8021 R8022 R8023 R8024 R8025 R8026 R8027 R8028 R8029 R8030 R8031 R8032 R8033 R8034 R8035 R8036 R8037 R8038 R8039 R8040 R8041 R8042 R8043 R8044 R8045 R8047 R8052 R8100 R8101 R8102 R8200 R8200 R8201 R8202 R8205 D-1 D-1 C-2 D-2 D-2 D-2 D-3 D-2 D-1 D-2 D-2 D-3 D-3 D-2 D-2 D-3 D-2 C-2 D-1 D-2 C-2 C-2 C-2 D-3 C-3 C-3 C-3 C-3 D-3 D-2 D-1 D-1 D-1 D-2 C-2 C-1 D-2 A-3 D-3 D-3 B-1 A-1 C-1 B-2 C-2 R8206 R8207 R8208 R8209 R8210 R8211 R8212 R8213 R8214 R8215 R8216 R8217 R8218 R8219 R8220 R8221 R8222 R8223 R8224 R8225 R8226 R8228 R8229 R8230 R8232 R8233 R8234 R8235 R8236 R8237 R8238 R8239 R8240 R8241 R8242 R8243 R8244 R8245 R8246 R8247 R8248 R8249 C-2 C-2 C-3 A-1 B-1 C-3 B-3 B-3 B-3 C-2 C-2 C-2 C-2 B-2 B-2 A-1 B-2 C-2 C-3 C-3 C-3 B-3 B-3 B-3 B-2 B-2 B-2 B-2 B-2 B-1 B-2 A-3 A-3 A-3 B-2 B-1 B-3 B-3 C-2 A-1 A-1 C-3
For printed wiring boards · This board is six-layer print board. However, the patterns of layers two to six have not been included in the diagram. · Chip parts Transistor
C 65 4
B
E
12 3
There are few cases that the part printed on this diagram isn't mounted in this model.
VF-136 (BACK-LIGHT DRIVE) CD-221 (CCD IMAGER)
PD-112 RGB DECODER, TIMING GENERATOR PR-32 (PANEL REVERSE) INVERTER TRANSFORMER UNIT
PO-4 (PANEL OPEN)
RGB DECODER, TIMING GENERATOR
PD-112
4-55
4-56
DCR-PC2E/PC3/PC3E
PD-112 BOARD (1/2)
CAMERA REC/PB
1 IC8001 8
H
0.26Vp-p
2 IC8001 9
0.2Vp-p H
3 IC8001 !º
0.22Vp-p H
4 IC8001 @º
7.5Vp-p
2H
5 IC8001 @TM
7.5Vp-p
2H
6 IC8001 @¢
7.5Vp-p
2H
7 IC8001 #¶
5Vp-p H
4-57
4-58
4-59
RGB DECODER
PD-112 (1/2)
DCR-PC2E/PC3/PC3E
For schematic diagram · Refer to page 4-55 for printed wiring board.
PD-112 BOARD (2/2)
8 IC8201 #¢
CAMERA REC/PB
17.9kHz
2.2Vp-p
TIMING GENERATOR
PD-112 (2/2)
4-60
4-61
4-62
DCR-PC2E/PC3/PC3E