Text preview for : 03_LcdDatasheet.pdf part of fujitsu siemens myrica v32-1 t32134 i need service manual for power supply
psm 192-240 from solder
thanks
Back to : 03_LcdDatasheet.pdf | Home
L2032
4.0 8.5 13.5
(2x20)
Unit: mm
General Tolerance
0.5 mm
108.0±0.3 93.0 83.0±0.3 4-¿3.5±0.2 14-¿1. 0±0.2 6.5 11.5
4.0
Reflective/EL Backlight
5.5max. 1.6±0.2
LED Backlight
10.0max. 1.6±0.2
4.0
6.88
2.5 14
37.0±1.0 29.0±0.3
18.6±0.3
2.54 13
2.54X6= 15.24
11.5
8.75
5.2
6.88
8.75
2
1
5.2
31.4 2.8
4.0
2.8
6.3 18.25 73.5 116.0±1.0 16.25 11.3max.
4.0max.
11.1 15.8max.
4.0max.
3.7 3.2 0.65 0.6 0.05 0.5
PIN FUNCTIONS
No. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 Name VSS VDD VLC RS R/W E DB0 DB1 DB2 DB3 DB4 DB5 DB6 DB7 Function GND Power supply voltage + 5 V Liquid crystal driving voltage L: Instruction code input. H: Data input L: Data write from MPU to LCM. H: Data read from LCM to MPU Enable Data bus line Data bus line Data bus line Data bus line Data bus line Data bus line Data bus line Data bus line
5.95
0.4
5.55
0.05
O PERATING I NSTRUCTIONS
INTRODUCTION
Seiko Instruments intelligent dot matrix liquid crystal display modules have on-board controller and LSI drivers, which display alpha numerics, Japanese KATA KANA characters and a wide variety of other symbols in either 5 x 7 dot matrix. The internal operation in the KS0066 controller chip is determined by signals sent from the MPU. The signals include: 1) Register select RS input consisting of instruction register (IR) when RS = 0 and data register (DR) when RS = 1; 2) Read/write (R/W); 3) Data bus (DB7~ DB0); and 4) Enable strobe (E) depending on the MPU or through an external parallel I/O port. Details on instructions data entry, execution times, etc. are explained in the following sections.
READ
AND
WRITE TIMING DIAGRAMS
AND
TABLES
The following timing characteristics are applicable for all of Seiko's LCD dot matrix character modules.
READ TIMING CHARACTERISTICS
V =5.0V ± 5%, V =OV, T =0 C TO 50 C
O O DD SS A
WRITE TIMING CHARACTERISTICS
V =5.0V ± 5%, V =OV, T =0 C TO 50 C
O O DD SS A
Item
Symbol
Standard Unit Min. Max. 500 230 -- 40 10 -- 5 -- -- 20 -- -- 160 -- ns ns ns ns ns ns ns
Item
Symbol
Standard Min. Max. 500 230 -- 40 10 80 10 -- -- 20 -- -- -- --
Unit
Enable cycle time Enable pulse width High Level
t CYCE PWEH tER, tEF tAS tAH tDDR tH
Enable cycle time Enable pulse width High Level
t CYCE PWEH tER, tEF tAS tAH tDSW tH
ns ns ns ns ns ns ns
Enable rise and fall time Address setup time Address hold time Data delay time Data hold time RS,R/W--E
Enable rise and fall time Address setup time Address hold time Data setup time Data hold time RS,R/W--E
READ OPERATION
RS VIH1 VIL1 tAS tAH VIH1 VIL1 RS VIH1 VIL1 tAS
WRITE OPERATION
VIH1 VIL1 tAH
R/W
VIH1 PWEH VIH1 VIL1 tEr tDDR tDHR VIH1 VIL1 tAH tE1
VIH1
R/W
VIL1 PWEH VIH1 VIL1 tEr tDSW tH VIH1 VIL1 tAH tE1
VIL1
E
VIL1
E
VIL1
DB0 to DB7
VOH1 * VOL1
Valid data tcycE
V * VOH1 OL1
DB0 to DB7
VIH1 VIL1
Valid data tcycE
VIH1 VIL1
Note: * VOL1 is assumed to be 0.8 V at 2 MHz operation.
DATA READ FROM MODULE TO MPU
DATA WRITE FROM MPU TO MODULE
O PERATING I NSTRUCTIONS
INTRODUCTION CODES
Instructlon RS Set R/W DB7 DB6 Instruction Code DB5 DB4 DB3 Description DB2 DB1 DB0 Clears all display memory and returns the cursor to the home position (Address 0). Returns the cursor to the home position (Address 0) shifted to the original position. DD RAM contents remain unchanged. Sets the cursor move direction and specifies to or not to shift the display. These operations write and read. (D) is display ON/OFF control; memory remains unchanged in OFF condition. (C) cursor ON/OFF (B) blinking cursor. Moves the cursor and shifts the display without changing DD RAM contents. Sets interface data length (DL), number of display lines (N), and character font (F). Sets the CG RAM address. CG RAM data is sent and received after this setting. Sets the DD RAM address. DD RAM data is sent and received after this setting. Reads Busy Flag (BF) indicating internal operation is being performed and reads address counter contents. Writes data into DD RAM or CG RAM. Reads data from DD RAM or CG RAM. Execution Time (when fcp or fosc is 250 kHz)
Clear Display
O
O
O
O
O
O
O
O
O
1
82 s ~ 1.64ms
Return Home
0
0
0
0
0
0
0
0
1
*
40 s ~ 1.6ms
Entry Mode Set Display ON/OFF Control
0
0
0
0
0
0
0
1
I/D
S
40 s ~ 1.64ms
0
0
0
0
0
0
1
D
C
B
40 s
Cursor or Display Shift Function Set
0
0
0
0
0
1
S/C
R/L
*
*
40 s
0
0
0
0
1
DL
N
F
*
*
40 s
Set CG RAM Address Set DD RAM Address Read Busy Flag & Address Write Data to CG or to DD RAM Read Data from CG or DD RAM * Doesn't matter
DD RAM: CG RAM: A CG: ADD:
0
0
0
1
A CG
40 s 40 s
0
0
1
ADD
0
1
BF
AC
1 s
40 s
1
0
Write Data
1
1
Read Data
40 s
Display data RAM Character generator RAM CG RAM address DD RAM address corresponds to cursor address Address counter used for both DD RAM and CG RAM address
I/D = 1: I/D = 0: S = 1: S = 0: D = 1: D = 0:
Increment Decrement Display shift No display shift Display ON Display OFF
C = 1: C = 0: B = 1: B = 0: S/C = 1: S/C = 0: BF = 1: BF = 0:
Cursor ON Cursor OFF Blink ON Blink OFF Display shift Cursor movement Internal operation in progress Instruction can be accepted
R/L = 1: R/L = 0: DL = 1: DL = 0: N = 1: F = 0:
Right shift Left shift 8 bits 4 bits 2 lines (L1671) 5 x 7 dot matrix
A C:
Execution times in the above table indicate the minimum values when operating frequency is 250 kHz. When fOSC is 270 kHz: 40 s x 250/250 = 37 s
O PERATING I NSTRUCTIONS
INTRODUCTION CODE EXPLANATIONS
The two registers 1) Instruction Register (IR) and the 2) Data Register (DR) in the KS0066 controller chip are directly controlled by the MPU. Control information is temporarily stored in these registers prior to internal operation start. This allows interface to various types of MPUs which operate at different speeds from that of the KS0066, and allows interface from peripheral control ICs. Internal operations of the KS0066 are determined from the signals sent from the MPU. These signals, including register selection signals (RS), Read/Write (R/W) and data bus signals (DB0 - DB7) are polled instructions.
REGISTER SELECTION
RS 0 0 1 1 R/W 0 1 0 1 Operation IR selection, IR write. Internal operation: Display clear Busy flag (DB7) and address counter (DB0 to DB6) read DR selection, DR write. Internal operation: DR to DD RAM or CG RAM DR selection, DR read. Internal operation: DD RAM or CG RAM to DR
ADDRESS COUNTER (AC)
The counter specifies an address when data is written into DD RAM or CG RAM and the data stored in DD RAM or CG RAM is read out. If an Address Set instruction (for DD RAM or CG RAM) is written in the IR, the address information is transferred from the IR to the AC. When display data is written into or read from DD RAM or CG RAM, the AC is automatically incremented or decremented by one according to the Entry Mode Set. The contents of the AC are output to DB0 to DB6; refer to above "Register Selection Table" when RS = 0 and R/W = 1. home position. In other words, the cursor returns to the first character block on the first line on all 1, 2, and 4 line character modules except L4044. I the above is entered on E2 (the second controller for lines 3 and 4), the cursor will return to the first character on the third line.
CLEAR DISPLAY
RS Code
0
R/W DB7
0 0 0 0 0 0 0 0
DB0
1
Clear all display memory and return the cursor to the
CURSOR HOME
RS Code
0
R/W DB7
0 0 0 0 0 0 0 1
DB0
*
*Doesn't matter
Returns cursor to home position. First line first character
blocks on all 1, 2 and 4 line display; except L4044 refer "clear display": (Address 0; ADD "80"). The contents of the DD RAM remain unchanged.
AND
RESTRICTIONS
ON
EXECUTION
OF
DISPLAY CLEAR
CURSOR HOME INSTRUCTIONS
Conditions of use When executing the Display Clear or Cursor Home instruction when the display is shifted (after execution of Display Shift instruction).
Restrictions The Cursor Home instruction should be executed again immediately after the Display Clear or Cursor Home instruction is executed. Do not leave an interval of a multiple of 400/fOSC* second after the first execution. · L4052: fOSC = 250 kHz · The other modules: fOSC = 270 kHz *fOSC: Oscillation frequency Before executing the Cursor Home instruction, the data of the four DD RAM addresses given at the left should be read and saved. After execution, write the data again in DD RAM. (This restriction is necessary to prevent the contents of the DD RAM addresses from being destroyed after the Cursor Home instruction has been executed.)
When 23H, 27H, 63H, or 67H is used as a DD RAM address to execute Cursor Home instruction.
O PERATING I NSTRUCTIONS
ENTRY MODE SET
RS Code
0
R/W DB7
0 0 0 0 0 0 1 I/D
DB0
S
I/D: Increments (I/D = 1) or decrements (I/D = 0) the DD RAM address by one block when writing or reading a character code from DD RAM or CG RAM. The cursor automatically moves to the right when incremented by one or to the left if decremented by one.
S: Shifts the entire display to either the right or left when S = 1 (high). When S = 1 and I/D = 1 the display shifts one position to the left. When S = 1 and 1/D = 0 the display shifts one position to the right. This right or left shift occurs after each data write to DD RAM. Display is not shifted when reading from DD RAM. Display is not shifted when S = 0.
DISPLAY
Code
AND
CURSOR ON/OFF CONTROL
R/W DB7
0 0 0 0 0 1 D C
RS
0
DB0
B
D: Display is turned ON when D = 1 and OFF when D = 0. When display is OFF, display data in DD RAM remains unchanged. Information comes back immediately when D = 1 is entered. C: Cursor is displayed when C = 1 and not displayed when C = 0. If the cursor disappears, function of I/D etc.
does not change during display data write. In a 5 x 7 dot matrix there is an eighth line which functions as the cursor. B: When B = 1, the character at the cursor position starts blinking. When B = 0 the cursor does not blink. The blink is done by stiching between the all black dot matrix and displayed character at 0.4 seconds intervals. The cursor and the blink can be set at the same time (fosc = 250 kHz).
DOT MATRIX
5
X
7
C = 1 (cursor display)
B = 1 (blinking)
Cursor
CURSOR
OR
DISPLAY SHIFT
R/W DB7
0 0 0 0 1 S/C R/L *
RS Code
0
DB0
*
* Doesn't Matter
Cursor/Display Shift moves the cursor or shifts the display without changing the DD RAM contents. The cursor position and the AC contents match. This instruction is available for display correction and retrieval because the cursor position or display can be shifted without writing or reading display data. In case of a 2-line display, the
cursor is shifted from character block 40 of line 1 to character block 1 of line 2. Displays of lines 1 and 2 are shifted at the same time. In case of a 4-line display, the cursor does not move continuously from line 2 to line 3. The cursor is shifted from character block 40 of line 3 to character block 1 of line 4. Displays of lines 3 and 4 are shifted at the same time. The display pattern of line 2 or 4 is not shifted to line 1 or 3.
S/C 0 0 1 1
R/L 0 1 0 1
Operation The cursor position is shifted to the left (the AC decrements one) The cursor position is shifted to the right (the AC increments one) The entire display is shifted to the left with the cursor The entire display is shifted to the right with the cursor
O PERATING I NSTRUCTIONS
FUNCTION SET
RS Code
0
R/W DB7
0 0 0 1 DL N F *
DB0
*
* Doesn't Matter
Function Set sets the interface data length, the number of display lines and the character font.
N 1 F 0 Number of display lines 2
DL: Interface data length When DL = 1, the data length is set at 8 bits (DB7 to DB0). When DL = 0, the data length is set at 4 bits (DB7 to DB4). The upper 4 bits are transferred first, then the lower 4 bits follow. N: Number of display lines F: Sets character font
Duty Cycle 1/16 LCD Module All character LCD modules
Character font 5 x 7 dot matrix
The Function Set instruction must be executed prior to all other instructions except for Busy Flag/Address Read. If another instruction is executed first, no function instruction except changing the interface data lenght can be executied.
CG RAM ADDRESS SET
RS Code
0
DATA WRITE
DB0
1 A A A A A A
TO
CG RAM
D D
OR
DD RAM
DB0
D D D D D D
R/W DB7
0 0
RS Code
1
R/W DB7
0
Upper bit
Lower bit
Upper bit
Lower bit
CG RAM addresses, expressed as binary AAAAAA, are set to the AC. Then data in CG RAM is written from or read to the MPU.
DD RAM ADDRESS SET
RS Code
0
Binary eight-bit data DDDDDDDD is written into CG RAM or DD RAM. The CG RAM Address Set instruction or the DD RAM Address Set instruction before this instruction selects either RAM. After the write operation, the address and display shift are determined by the entry mode setting.
R/W DB7
0 1 A A A A A A
DB0
A
DATA READ
RS Code
1
TO
CG RAM
1 D
OR
DD RAM
DB0
D D D D D D
R/W DB7
D
Upper bit
Lower bit
DD RAM addresses expressed as binary AAAAAA are set to the AC. Then data in DD RAM is written from or read to the MPU.
Upper bit
Lower bit
Binary eight-bit data DDDDDDDD is read from CG RAM or DD RAM. The CG RAM Address Set instruction or the DD RAM Address Set instruction before this instruction selects BUSY FLAG/ADDRESS READ either RAM. In addition, either instruction is executed immeRS R/W DB7 DB0 diately before this instruction. If no Address Set instruction is executed before a read instruction, the first data read Code 0 0 BF A A A A A A A becomes invalid. If read instructions are executed consecuUpper bit Lower bit tively, data is normally read from the second time. However, The BF signal can be read to verify if the controller is indi- if the cursor is shifted by the Cursor Shift instruction when cating that the module is working on a current instruction. reading DD RAM, there is no need to execute an address set instruction because the Cursor Shift instruction does this. When BF = 1, the module is working internally and the next After the read operation, the address is automatically instruction cannot be accepted until the BF value becomes 0. incremented or decremented by one according to the entry When BF = 0, the next instruction can be accepted. mode, but the display is not shifted. Therefore, make sure that BF = 0 before writing the next instruction. The AC values of binary AAAAAA are read out at Note: The AC is automatically incremented or decremented by the same time as reading the busy flag. The AC addresses one according to the entry mode after a write instruction is are used for both CG RAM and DD RAM but the address set excecuted to write data in CG RAM or DD RAM. However, the before execution of the instruction determines which address data of the RAM selected by the AC are not read out even if a is to be used. read instruction is executed immediately afterwards.
O PERATING I NSTRUCTIONS
5
X
7 + CURSOR
Relationships between CG RAM addresses and character codes (DD RAM) and character patterns (CG RAM data), (5 x 7 dot matrix).5 X 7 Table
Character code (DD RAM data) 7 6 5 4 r Upper bit 3 2 1 0 Lower bit R
CG RAM address 5 4 3 r Upper bit 2 1 0 Lower bit R 0 0 0 0 1 1 1 1 0 0 0 0 1 1 1 1 0 0 0 0 1 1 0 0 1 1 0 0 1 1 0 0 1 1 0 0 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1
Character pattern (CG RAM data) 7 6 5 4 r Upper bit * * * 1 1 1 1 1 1 1 0 1 0 1 0 1 0 0 0 3 1 0 0 1 0 0 0 0 0 1 1 0 1 0 0 0 2 1 0 Lower bit R 1 0 0 1 1 0 0 0 0 0 1 1 1 1 1 0 1 0 0 1 0 1 0 0 0 1 1 0 1 0 0 0 0 1 1 0 0 0 1 0 1 0 1 0 1 0 0 0 Example of character pattern (R)
0
0
0
0
*
0
0
0
0
0
0
* *
* *
* *
r Cursor position
0
0
0
0
*
0
0
1
0
0
1
Example of character pattern (Y) =
* *
* *
* *
0
0
0
0
*
1
1
1
1
1
1 1 1 1 1 0 0 1 1 0 1 0 1
*
*
*
NOTES:
In CG RAM data, 1 corresponds to Selection and 0 to Non-selection on the display. Character code bits 0 to 2 and CG RAM address bits 3 to 5 correspond with each other (three bits, eight types). CG RAM address bits 0 to 2 specify a line position for a character pattern. Line 8 of a character pattern is the cursor position where the logical sum of the cursor and CG RAM data is displayed. Set the data of line 8 to 0 to display the cursor. If the data is charged to 1, one bit lights, regardless of the cursor. The character pattern column position corresponds to CG RAM data bits 0 to 4 and bit 4 comes to the left end. CG RAM data bits 5 to 7 are not displayed but can be used as general data RAM. When reading a character pattern from CG RAM, set to 0 all of character code bits 4 to 7. Bits 0 to 2 determine which pattern will be read out. Since bit 3 is not valid, 00H and 08H select the same character.
O PERATING I NSTRUCTIONS
PROGRAMMING
THE
CHARACTER GENERATOR RAM (CG RAM)
If during initialization the display was programmed to automatically increment, then only the single initial address, 40, need be sent. Consecutive row data will automatically appear at 41, 42, etc. until the completed character is formed. All eight custom CG characters can be programmed in 64 consecutive "writes" after sending the single initial 40 address. The CG RAM is 8 bits wide, although only the right-most 5-bits are used for a custom CG character row. The left-most dot of programming the CG RAM character corresponds to D4 in the most significant nibble (XXXD4) of the data bus code, with the remaining 4 dots in the row corresponding to the least significant nibble (D3 thru D0), D0 being the rightmost dot. Thus, hex 1F equals all dots on and hex 00 equals all dots off. Examples include hex 15 (10101) equal to 3 dots on the hex 0A (01010) equal 2 dots on. In each case the key 5-bits of the 8-bit code program one row of a custom CG character. When all 7 or 8 rows are programmed, the character is complete. A graphic example is shown below:
The character generator RAM (CG RAM) allows the user to create up to eight custom 5 x 7 characters + cursor (5 x 8). Once programmed, the custom characters or symbols are accessed exactly as if they were in ROM. However since the RAM is a volatile memory, power must be continually maintained. Otherwise, the custom characters/symbols must be programmed into non-volatile external ROM and sent to the display after each display initialization. All dots in the 5 x 8 dot matrix can be programmed, which includes the cursor position. The modules RAM are divided into two parts: data display RAM (DD RAM) and custom character generator RAM (CG RAM). This is not to be confused programming the custom character generator RAM with the 192 character generator ROM. The CG RAM is located between hex 40 and 7F and is contiguous. Locations 40 thru 47 hold the first custom character (5 x 8), 48 thru 4F hold the second custom character, 50 thru 57 hold the third CG, and so forth to 78 thru 7F for the eighth CG character/symbol.
RS 0 1 1 1 1 1 1 1 1 1
R/W 0 0 0 0 0 0 0 0 0 0
Data 40 11 0A 1F 04 1F 04 04 00 15
Display -- * * ** ***** * ***** * * -- ***
Description addresses 1st row, 1st CG character result of 11, 1st row result of 0A, 2nd row result of 1F, 3rd row result of 04, 4th row result of 1F, 5th row result of 04, 6th row result of 04, 7th row result of 00, 8th row (cursor position) 1st row, 2nd CG character. Note: Addressing not now required; hex 48 is next in the sequence.
O PERATING I NSTRUCTIONS
ADDRESS LOCATIONS
1)
Line 1
L1671-SERIES (16 characters x 1 line)
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 80 81 82 83 84 85 86 87 C0 C1 C2 C3 C4 C5 C6 C7 NOTE: L1671 series is initialized as a 2 line display, because of the absence of an LCD driver. You must address character no. 9 as you would the first position on the 2nd line which is (CO).
2)
L1672-SERIES (16 characters x 2 lines) L1682-SERIES L1692-SERIES
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 80 81 82 83 84 85 86 87 88 89 8A 8B 8C 8D 8E 8F C0 C1 C2 C3 C4 C5 C6 C7 C8 C9 CA CB CC CD CE CF
Line 1 Line 2
3)
Line 1 Line 2 Line 3 Line 4
L1634-SERIES (16 characters x 4 lines)
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 80 81 82 83 84 85 86 87 88 89 8A 8B 8C 8D 8E 8F C0 C1 C2 C3 C4 C5 C6 C7 C8 C9 CA CB CC CD CE CF 90 91 92 93 94 95 96 97 98 99 9A 9B 9C 9D 9E 9F D0 D1 D2 D3 D4 D5 D6 D7 D8 D9 DA DB DC DD DE DF
4)
Line 1 Line 2
L2032-SERIES (20 characters x 2 lines)
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 80 81 82 83 84 85 86 87 88 89 8A 8B 8C 8D 8E 8F 90 91 92 93 C0 C1 C2 C3 C4 C5 C6 C7 C8 C9 CA CB CC CD CE CF D0 D1 D2 D3
5)
Line 1 Line 2 Line 3 Line 4
L2034-SERIES (20 characters x 4 lines)
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 80 81 82 83 84 85 86 87 88 89 8A 8B 8C 8D 8E 8F 90 91 92 93 C0 C1 C2 C3 C4 C5 C6 C7 C8 C9 CA CB CC CD CE CF D0 D1 D2 D3 94 95 96 97 98 99 9A 9B 9C 9D 9E 9F A0 A1 A2 A3 A4 A5 A6 A7 D4 D5 D6 D7 D8 D9 DA DB DC DD DE DF E0 E1 E2 E3 E4 E5 E6 E7
6)
Line 1 Line 2
L2462-SERIES (24 characters x 2 lines)
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 80 81 82 83 84 85 86 87 88 89 8A 8B 8C 8D 8E 8F 90 91 92 93 94 95 96 97 C0 C1 C2 C3 C4 C5 C6 C7 C8 C9 CA CB CC CD CE CF D0 D1 D2 D3 D4 D5 D6 D7
7)
L4052-SERIES (40 characters x 2 lines) L4044-SERIES (40 characters x 4 lines)
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 80 81 82 83 84 85 86 87 88 89 8A 8B 8C 8D 8E 8F 90 91 92 93 94 95 96 97 98 99 9A 9B 9C 9D 9E 9F A0 A1 A2 A3 A4 A5 A6 A7 C0 C1 C2 C3 C4 C5 C6 C7 C8 C9 CA CB CC CD CE CF D0 D1 D2 D3 D4 D5 D6 D7 D8 D9 DA DB DC DD DE DF E0 E1 E2 E3 E4 E5 E6 E7 80 81 82 83 84 85 86 87 88 89 8A 8B 8C 8D 8E 8F 90 91 92 93 94 95 96 97 98 99 9A 9B 9C 9D 9E 9F A0 A1 A2 A3 A4 A5 A6 A7 C0 C1 C2 C3 C4 C5 C6 C7 C8 C9 CA CB CC CD CE CF D0 D1 D2 D3 D4 D5 D6 D7 D8 D9 DA DB DC DD DE DF E0 E1 E2 E3 E4 E5 E6 E7
Line 1 Line 2 Line 3 Line 4
Note: Address locations on lines 1 & 2 are controlled by enabling E1.
Address locations on lines 3 & 4 are controlled by enabling E2.
O PERATING I NSTRUCTIONS
CHARACTER FONT CODES (5
X
7
DOT MATRIX)
Upper 4 Bit Hexadecimal
Lower 4 Bit Hexadecimal
O PERATING I NSTRUCTIONS
EXAMPLES
DISPLAY
OF
8-BIT
AND
4-BIT DATA TRANSFER OPERATION
mode. All the initialization sequences are performed under the condition of Register Select (RS) = 0 (low) and Read/Write (R/W) = 0 (low). The 4-bit data bus microcontroller may operate the display module by sending the initialization sequence in 4-bit format. Since 4-bit operation requires the data to be sent twice over the higher 4-bit bus lines (D4-D7), memory requirements are doubled.
INITIALIZATION
Each time the module is turned on or reset, an initialization procedure must be executed. The procedure consists of sending a sequence of hex codes from the microprocessor or parallel I/O port. The initialization sequence turns on the cursor, clears the display, and sets the module onto an auto-increment mode. The initial hex code 30, 34, or 38 is sent two or more times to ensure the module enters the 8-bit or 4-bit data
A. EXAMPLE
FOR THE MODULE WITH
5
X
7 Character Format Under 8-Bit Data Transfer
The 4-bit data bus microcontroller may operate the display module by sending the initialization sequence in 4-bit format. Since 4-bit operation requires the data to be sent twice over the higher 4-bit bus lines (D4-D7), memory requirements are doubled.Diagram B. Example for the module with 5 x 7 character format under 4-bit data transfer
Note:
1) 2) 3)
Both RS and R/W terminals shall be "0" in this sequence. RS, R/W and Data are latched at the falling edge of the Enable signal, (falling edge is typically 10nSec; Max: 20nSec). L4044 has t obe initialized on E1 and E2 respectively.
O PERATING I NSTRUCTIONS
EXAMPLES
B. EXAMPLE
OF
8-BIT
AND
4-BIT DATA TRANSFER OPERATION
5
X
FOR THE MODULE WITH
7 Character Format Under 4-Bit Data Transfer
Note:
1) 2) 3)
Both RS and R/W terminals shall be "0" in this sequence. RS, R/W and Data are latched at the falling edge of the Enable signal, Enable signal has to be sent after every 4-bit Data transfer.
O PERATING I NSTRUCTIONS
1) Display "THIS IS SEIKO LCD MODULE" on L1672. Set RS = R/W = 0 (low), then send hex codes 38, 38, 06, 0E, 01, 80. (80 is the home position of the DD RAM) Set RS = 1 and R/W = 0, then send hex codes 54, 48, 49 ,53, 20, 49, 53, 20, 53 ,45,49, 4B, 4F. Set RS = R/W = 0, then send hex code C0 to start from beginning of the second line. Set RS = 1 and R/W = 0, then send hex codes 4C, 43, 44, 20, 4D, 44, 55, 4C, 45. Display "ONE", "TWO", "THREE", and "FOUR" on each line of L4044. Set RS = R/W = E2 = 0, E1 = 1, then send hex codes 38, 38, 06, 0E, 01, 80. Set RS = R/W = E1 = 0, E2 = 1, then send hex codes 38, 06, 0C, 01. Set RS = E1 = 1, R/W = E2 = 0, then send hex codes 4F, 4E, 45. Set RS = R/W = E2 = 0, E1 = 1, then send hex code C0. Set RS = E1 = 1, R/W = E2 = 0, then send hex codes 54, 57, 4F. 2) Set RS = R/W = E2 = 0, E1 code 0C. Set RS = R/W = E1 = 0, E2 codes 0E, 80. Set RS = E2 = 1, R/W = E1 codes 45, 48, 52, 45, 45. Set RS = R/W = E1 = 0, E2 code C0. Set RS = E2 = 1, R/W = E1 code 46, 4F, 55, 52. = 1, then send hex = 1, then send hex = 0, then send hex = 1, then send hex = 0, then send hex
2)
Display "L1671 LCD MODULE" on L1671. (Special case in the LCD modules) Set RS = R/W = 0, then send hex codes 38, 38, 06, 0E, 01, 80. Set RS = 1 and R/W = 0, then send hex codes 38, 06, 0C, 01. Set RS = R/W = 0, then send hex code C0 to start from 9th character. Set RS = 1 and R/W = 0, then send hex codes 44, 20, 4D, 4F, 44, 55, 4C, 45.
INTERFACE PROBLEMS
AND
POSSIBLE SOLUTIONS
Allow 1.6mS, after entering hexadecimal 01 or 02 at the end of the initialization sequence, then enter data. Time interval between other data entries should be 50uS or greater. Failure to properly initialize the display: Check initialization examples for either 4 or 8-bit. Make sure to enter first hexadecimal entry at least twice in the initialization sequence. This sets the LCD to either a 1 or 2 line display. LCD input assumed to be configured as an IC. (This is not correct.) Check the time interval on the falling edge of the enable pulse. Should not exceed 20nS (typical is 10nS). Enable pulse width is shorter than 230nS. More than one external bus being selected: Check data bus connection. Signal levels are too low: Insure that V(IH & OH) is more than 2.4 volts. All data bus components do not have TTL type outputs. VDD and VSS pins are reversed. Too much voltage on VDD - (Max. 7VDC). Load being put on data lines, when power is OFF on the VDD pin. Check address locations for the first position on the second line for each 2 lines (ref: Address Location Chart). L4044 has two controllers: E1 for lines 1 & 2 and E2 for lines 3 & 4. Initialization must be done for E1 and the same for E2.
Although the following problems and possible solutions are not all inclusive, they do represent the most common problems experienced not only by the first-time user, but also experienced users. If the user is experiencing problems, please review all of the following information. If the user still has problems, please call Seiko Instruments in Torrance, California at (310) 517-7771.
SYMPTOMS
4)
1) 2) 3) 4) 5)
Display is blank after power ON and initialization: Check 1- 6. Wrong information being displayed: Check 3,4,6,7,8,9. Symptoms same as 2, except multiple components are tied to the data bus: Check 8,9,10. ICs become HOT: Check 1,11,12,13. Cannot enter information to the 2nd line or lines 3 and 4 of the 4-line display: Check 4,14,15.
5) 6) 7) 8) 9) 10) 11) 12) 13) 14)
POSSIBLE SOLUTION(S)
1) 2)
Check +5 VDC and ground lines and connections. A variable resistor or fixed resistor must be used on the VLC pin for all LCD modules. VLC voltage range is: 0~.7 volts (ref: Contrast Adjustment Circuit). Data is being transmitted too fast: Wait 4.5 mS after Power ON, or until VDD reaches 4.5 volts. Wait more than 15 mS after VDD reaches 4.5 volts.
3)
15)