Text preview for : Pioneer-A407 amp.pdf part of Pioneer A407 integrated amplifier
Back to : Pioneer-A407 amp.pdf | Home
STEREO AMPLIFIER
A-407R Direct Energy MOS
VOLUME TAPE 2
MONITOR
STANDBY/ON STANDBY
CD
TUNER
PHONO
LINE
TAPE 1 /MD
POWER
OFF ON
A SPEAKERS B
BASS
TREBLE
BALANCE
INPUT SELECTOR
REC SELECTOR
CD
TUNER
OFF
SOURCE
PHONES
LOUDNESS
DIRECT
MIN
MAX
L
R
ORDER NO.
RRV1958
STEREO AMPLIFIER
A-407R
THIS MANUAL IS APPLICABLE TO THE FOLLOWING MODEL(S) AND TYPE(S).
Type
MY/EW MY/GR MV
Model A-407R
AC220 230V AC220 230V AC220 230V
Power Requirement
Remarks
CONTENTS
1. SAFETY INFORMATION ...................................... 2 2. EXPLODED VIEWS AND PARTS LIST ................ 3 3. SCHEMATIC DIAGRAM ....................................... 6 4. PCB CONNECTION DIAGRAM .......................... 14 5. PCB PARTS LIST ............................................... 19 6. ADJUSTMENT .................................................... 22 PIONEER ELECTRONIC CORPORATION 7. GENERAL INFORMATION ................................ 23 7.1 IC INFORMATION ....................................... 23 7.2 BLOCK DIAGRAM ....................................... 24 8. PANEL FACILITIES AND SPECIFICATIONS .... 25
4-1, Meguro 1-Chome, Meguro-ku, Tokyo 153-8654, Japan PIONEER ELECTRONICS SERVICE, INC. P.O. Box 1760, Long Beach, CA 90801-1760, U.S.A. PIONEER ELECTRONIC (EUROPE) N.V. Haven 1087, Keetberglaan 1, 9120 Melsele, Belgium PIONEER ELECTRONICS ASIACENTRE PTE. LTD. 501 Orchard Road, #10-00 Wheelock Place, Singapore 238880
c PIONEER ELECTRONIC CORPORATION 1998
T - IZK MAY 1998 Printed in Japan
A-407R
1. SAFETY INFORMATION
This service manual is intended for qualified service technicians ; it is not meant for the casual do-ityourselfer. Qualified technicians have the necessary test equipment and tools, and have been trained to properly and safely repair complex products such as those covered by this manual. Improperly performed repairs can adversely affect the safety and reliability of the product and may void the warranty. If you are not qualified to perform the repair of this product properly and safely, you should not risk trying to do so and refer the repair to a qualified service technician.
WARNING Lead in solder used in this product is listed by the California Health and Welfare agency as a known reproductive toxicant which may cause birth defects or other reproductive harm (California Health & Safety Code, Section 25249.5). When servicing or handling circuit boards and other components which contain lead in solder, avoid unprotected skin contact with the solder. Also, when soldering do not inhale any smoke or fumes produced.
NOTICE (FOR CANADIAN MODEL ONLY) Fuse symbols (fast operating fuse) and/or be of identical designation.
(slow operating fuse) on PCB indicate that replacement parts must
REMARQUE (POUR MODÈLE CANADIEN SEULEMENT) Les symboles de fusible (fusible de type rapide) et/ou de remplacement doivent avoir la même désignation.
(fusible de type lent) sur CCI indiquent que les pièces
(FOR USA MODEL ONLY)
1. SAFETY PRECAUTIONS
The following check should be performed for the continued protection of the customer and service technician.
ANY MEASUREMENTS NOT WITHIN THE LIMITS OUTLINED ABOVE ARE INDICATIVE OF A POTENTIAL SHOCK HAZARD AND MUST BE CORRECTED BEFORE RETURNING THE APPLIANCE TO THE CUSTOMER.
LEAKAGE CURRENT CHECK
Measure leakage current to a known earth ground (water pipe, conduit, etc.) by connecting a leakage current tester such as Simpson Model 229-2 or equivalent between the earth ground and all exposed metal parts of the appliance (input/output terminals, screwheads, metal overlays, control shaft, etc.). Plug the AC line cord of the appliance directly into a 120V AC 60Hz outlet and turn the AC power switch on. Any current measured must not exceed 0.5mA.
2. PRODUCT SAFETY NOTICE
Many electrical and mechanical parts in the appliance have special safety related characteristics. These are often not evident from visual inspection nor the protection afforded by them necessarily can be obtained by using replacement components rated for voltage, wattage, etc. Replacement parts which have these special safety characteristics are identified in this Service Manual. Electrical components having such features are identified by marking with a on the schematics and on the parts list in this Service Manual. The use of a substitute replacement component which does not have the same safety characteristics as the PIONEER recommended replacement one, shown in the parts list in this Service Manual, may create shock, fire, or other hazards. Product Safety is continuously under review and new instructions are issued from time to time. For the latest information, always consult the current PIONEER Service Manual. A subscription to, or additional copies of, PIONEER Service Manual may be obtained at a nominal charge from PIONEER.
Device under test Test all exposed metal surfaces
Reading should Leakage not be above current 0.5mA tester
Also test with plug reversed (Using AC adapter plug as required)
Earth ground
AC Leakage Test
2
A-407R
2. EXPLODED VIEWS AND PARTS LIST
NOTES:
· Parts marked by "NSP" are generally unavailable because they are not in our Master Spare Parts List. · The mark found on some component parts indicates the importance of the safety factor of the part. Therefore, when replacing, be sure to use parts of identical designation. · Screws adjacent to mark on the product are used for disassembly.
(1) PACKING PARTS LIST
Except MV type 15 5 6 7 1 (Except MY/GR type) 2 (MY/EW and MY/GR types Only) 3 (MY/EW type Only) 4 Separate
NSP NSP NSP
2.1 PACKING
MV type Only 16 17 14
Mark No.
1
Description
Part No.
Operating Instructions See Contrast table(2) (English) 2 Operating Instructions See Contrast table(2) (German) 3 Operating Instructions See Contrast table(2) (French/Italian/Dutch/Swedish/Spanish/Portugese) 4 5 6 7 8 9 10 11 12 13 14 15 16 17 Warranty Card Remote Control Unit (CU-A013) Battery Cover Dry Cell Battery (R6P,AA) Side Protector L Side Protector R ····· Packing Case Literature Bag Packing Sheet Air Cap Power Cord Power Cord with Fuse Fuse (T5A) ARY7008 AXD7164 AZN2249 AEX-010 AHA7127 AHA7128 AHD7565 AHG-117 AHG1016 See Contrast table(2) See Contrast table(2) See Contrast table(2) See Contrast table(2)
12 Separate 13 8
FR
ON
NSP
T
9
11
(2) CONTRAST TABLE
A-407R/MY/EW, MY/GR and MV are constructed the same except for the following :
Mark No. Symbol and Description Part No. MY/EW Type ARB7139 ARC7187 ARC7188 MY/GR Type Not used ARC7187 Not used MV Type ARB7139 Not used Not used Remarks
1 Operating Instructions (English) 2 Operating Instructions (German) 3 Operating Instructions (French/Italian/Dutch/Swedish/Spanish/Portuguese) NSP 14 15 16 17 Air Cap Power Cord Power Cord with Fuse Fuse (T5A)
Not used ADG1154 Not used Not used
Not used ADG1154 Not used Not used
AHG1087 Not used ADG1156 AEK1046
3
A-407R
2.2 EXTERIOR
42 39 36 42 42 39 39
8 15 16 19 4 48 44 3 43 34 37 5 2 28 7 15 45 45 44 44 6 26 1 15 45 15 45 15 26 24 24 15 45 15 26 39
18 41 38 47 30 27 16 49 9 10 10 41 27 35 43 17
17 45 17 13 20
MY/EW, MY/GR Types only 42 39 42 42 42
29
11
23
23 23
42 40
46 31 33 31 32 42 14 22 26 21 21 25 12
23
23
14 26
4
A-407R
(1) EXTERIOR PARTS LIST
Mark No.
1 2 3 4 5 6 7 8 9 10 NSP 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25
Description
FRONT L Assy FRONT R Assy POWER SW Assy AC PRIMARY Assy HEADPHONE Assy VOLUME Assy AF Assy Fuse (FU1, T2A L250V) Flexible Cable (J1, 21P) (AF CN202 - FRONT R CN601) Washer Power Transformer (T1) Chassis Rear Panel Insulator Screw Screw Screw (4 × 10) Nut PCB Mold Barrier PCB Holder Stud Cover PCB Mold Radiator Plate B Locking Card Spacer
Part No.
AWX7054 AWX7050 AWX7057 See Contrast table(2) AWX7052 AWX7055 AWX7053 AEK1057 ADD1114 ABE1002 ATS7202 ANA7048 See Contrast table(2) PNW2766 ABA1018 ABA1050 ABA7047 ABN-065 AMR7222 AEC7072 AEC7057 AEC7096 AMR1525 AMR7223 DEC1908
Mark No.
26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49
Description
Screw LED Lens IR Filter LED Lens T Name Plate Rotary Knob A Rotary Knob B Volume Knob Speaker Button Main Power Button Bonnet Case Panel Base Front Panel Screw Terminal Screw Nut Screw Screw Screw Washer LED Lens B LED Lens Power Button Screw
Part No.
ABA-298 AAK2459 AAK7532 AAK7544 AAM7004 AAB7148 AAB7149 AAB7147 AAD7435 AAD7437 ANE7185 AMB7484 ANB7112 BBT30P080FZK AKE-031 NK90FUC ABA1006 ABA1009 BPZ30P080FMC WG40FCC AAK7538 PNW2019 AAD7436 BMZ30P080FCU
NSP
NSP NSP NSP NSP
(2) CONTRAST TABLE
A-407R/MY/EW, MY/GR and MV are constructed the same except for the following :
Mark No. Symbol and Description Part No. MY/EW Type AWX7051 ANC7646 MY/GR Type AWX7051 ANC7646 MV Type AWX7056 ANC7660 Remarks
4 AC PRIMARY Assy 13 Rear Panel
5
1
2
3
4
A-407R
3. SCHEMATIC DIAGRAM
3.1 OVERALL CONNECTION DIAGRAM
A
F
HEADPHONE ASSY (AWX7052)
D FRONT R ASSY
(AWX7050)
B
A AF ASSY
(AWX7053)
C
C VOLUME ASSY
(AWX7055)
D
6
1 2 3 4
5
6
7
8
A-407R
Note : When ordering service parts, be sure to refer to "EXPLODED VIEWS and PARTS LIST" or "PCB PARTS LIST".
A
B FRONT L ASSY
(AWX7054)
E AC PRIMARY ASSY
(MY/EW, MY/GR : AWX7051) (MV : AWX7056)
G POWER SW
ASSY (AWX7057)
B
C
D
7
5 6 7 8
1
2
3
4
A-407R 3.2 AF ASSY C
CN501
A
B
C
D
: AUDIO SIGNAL ROUTE
8
A
1
2
3
4
5
6
7
8
A-407R D
CN601
E
CN803
A
A AF ASSY (AWX7053)
B
TO POWER TRANSFORMER T1
C
L406 ATX1012
D
F
5 6
J5
7
A
8
9
1
2
3
4
A-407R 3.3 FRONT L AND VOLUME ASSEMBLIES
A
B FRONT L ASSY (AWX7054)
B
C
D
10
B
1
2
3
4
D
J4
FRONT L ASSY S 701 : POWER STANDBY/ON S 702 : LOUDNESS S 703 : SPEAKERS A S 704 : SPEAKERS B
5
6
7
8
A-407R
A
C VOLUME ASSY (AWX7055)
B
C
A
CN203
: AUDIO SIGNAL ROUTE
D
5
6
7
C
8
11
1
2
3
4
A-407R 3.4 FRONT R, AC PRIMARY, HEADPHONE AND POWER SW ASSEMBLIES
A
E
AC PRIMARY ASSY (MY/EW, MY/GR : AWX7051) (MV : AWX7056)
FU1 T2A L 250V AEK1057
(A-407R/MY/EW, MY/GR ONLY)
TO POWER TRANSFORMER T1
J2
NP
1/50 YA
A
47/10
AC POWER CORD
B
· NOTE FOR FUSE REPLACEMENT CAUTION - FOR CONTINUED PROTECTION AGAINST RISK OF FIRE. REPLACE WITH SAME TYPE AND RATINGS ONLY.
D FRONT R ASSY (AWX7050)
C
D
12
D E
1
2
3
4
5
6
7
8
A-407R
A
G POWER SW ASSY (AWX7057)
A
CN401
F
HEADPHONE ASSY (AWX7052)
B
FRONT R ASSY S 601 : INPUT SELECTOR S 603 : TAPE2 MONITOR S 604 : DIRECT S 606 : REC SELECTOR
CN202
TC74HC107AP
B
D
TC74HC00AP
5
6
7
D F G
8
13
CN701
A
C
1
2
3
4
A-407R
4. PCB CONNECTION DIAGRAM
4.1 AF ASSY
A
A
AF ASSY
POWER TRANSFORMER T1
E
CN803
B
NOTE FOR PCB DIAGRAMS:
1. Part numbers in PCB diagrams match those in the schematic diagrams. 2. A comparison between the main parts of PCB and schematic diagrams is shown below.
Symbol in PCB Diagrams Symbol in Schematic Diagrams Part Name
B B C E B B C E D D G S G
C
E B
C
E Transistor
C
E B
C
E Transistor with resistor
G
S D
G
S Field effect transistor
D
S G
D
S MOS Field effect transistor
C
S D G 1 3 2 S G
Resistor array
3-terminal regulator 3. The parts mounted on this PCB include all necessary parts for several destination. For further information for respective destinations, be sure to check with the schematic diagram. 4. Viewpoint of PCB diagrams
Capacitor Connector
SIDE A SIDE B
P.C.Board
Chip Part
D
C SIDE A
CN501
F
14
A
1
J5
2 3 4
5
6
7
8
A-407R
Q401
A
Q406 Q413 Q414
Q451 IC451 IC151 IC452 Q452
B
IC101 Q409 Q410 Q411 Q407 Q412 Q323 Q408 Q324
Q319 Q101 Q151 Q322 Q104 Q153 VR301 VR302 Q313 Q318
C
D CN601
Q309 Q312 Q325
Q334
IC301 Q301 Q304
D
IC251
(ANP7227-A) 5 6 7
Q251
A
8
15
1
2
3
4
A-407R
4.2 FRONT L AND VOLUME ASSEMBLIES
A
B FRONT L ASSY
D J4
B
(ANP7227-A)
VR752 Q701 Q702 Q707 Q706 Q704 Q703 IC751 Q751 Q752
VR751 Q705
SIDE A
Q502
Q501
C
Q503 Q507
Q509 Q506 Q505 Q504 Q510 Q508 Q513 Q512
D
A
CN203
Q511
Q514
C VOLUME ASSY
16
(ANP7227-A)
B C
1
2
3
4
1
2
3
4
A-407R
4.3 FRONT R ASSY
D FRONT R ASSY
Q616 Q606
A
Q610 Q617
IC603 Q609 Q608 IC602 Q618
Q605
B
Q604 IC601 Q603
A
Q602
CN202
VR601
C
Q601 Q612
Q613
Q611 Q614 Q615 Q607
(ANP7228-A)
J4
D
B CN701
SIDE A
1
2
3
D
4
17
1
2
3
4
A-407R
4.4 AC PRIMARY, HEADPHONE AND POWER SW ASSEMBLIES
A
G F
HEADPHONE ASSY
A CN401
POWER SW ASSY
B
(ANP7228-A)
(ANP7228-A)
POWER TRANSFORMER T1
AC POWER CORD
LIVE
NEUTRAL
C
A
J2
D
E
AC PRIMARY ASSY
Q811 IC811
(ANP7228-A)
SIDE A
18
E F G
1
2
3
4
A-407R
Mark No. Description Part No. Mark No. Description Part No.
5. PCB PARTS LIST
NOTES:
· Parts marked by "NSP" are generally unavailable because they are not in our Master Spare Parts List. · The mark found on some component parts indicates the importance of the safety factor of the part. Therefore, when replacing, be sure to use parts of identical designation. · When ordering resistors, first convert resistance values into code form as shown in the following examples.
Ex.1 When there are 2 effective digits (any digit apart from 0), such as 560 ohm and 47k ohm (tolerance is shown by J=5%, and K=10%). 561 ........................................................ RD1/4PU 5 6 1 J 560 56 × 101 473 ........................................................ RD1/4PU 4 7 3 J 47k 47 × 103 0.5 R50 ..................................................................................... RN2H R 5 0 K 1 1R0 ..................................................................................... RS1P 1 R 0 K Ex.2 When there are 3 effective digits (such as in high precision metal film resistors). 5621 ...................................................... RN1/4PC 5 6 2 1 F 5.62k 562 × 101
LIST OF WHOLE PCB ASSEMBLIES
Mark Symbol and Description Part No. MY/EW Type
AWK7422 AWX7053 AWX7054 AWX7055 AWG7009 AWX7050 AWX7051 AWX7052 AWX7057
MY/GR Type
AWK7422 AWX7053 AWX7054 AWX7055 AWG7009 AWX7050 AWX7051 AWX7052 AWX7057
MV Type
AWK7422 AWX7053 AWX7054 AWX7055 AWG7010 AWX7050 AWX7056 AWX7052 AWX7057
Remarks
NSP AF COMPLEX ASSY AF ASSY FRONT L ASSY VOLUME ASSY NSP CONTROL ASSY FRONT R ASSY AC PRIMARY ASSY NSP HEADPHONE ASSY POWER SW ASSY
Mark No.
Description
Part No.
Mark No.
Description
Part No.
HZS9A1L MTZJ10C MTZJ36B MTZJ4.7A S5688G ATX1012 LAU221J ASR7014 RSR1026 ACH1237 ACH7027 ACH7085 ACH7086 CCCSL101J50 CCCSL101J50 CCCSL221J50 CCCSL221K2H CCCSL330K2H CCCSL390J50 CCCSL470K2H CEANP1R0M50 CEANP470M10 CEAS100M50 CEAS101M25 CEAS102M50 CEAS221M25 CEAS2R2M2A
A AF ASSY
SEMICONDUCTORS
IC151 IC451 IC452 IC251 IC101 IC301 Q327,Q328,Q409,Q410 Q321,Q322 Q311-Q314,Q329,Q330 Q309,Q310,Q315,Q316 Q333,Q334 Q319,Q320 Q317,Q318,Q331,Q332 Q407,Q408 Q303,Q304 Q451 Q102,Q104,Q153,Q403-Q406 Q414 Q401,Q402,Q413 Q101,Q103,Q151 Q152,Q251 Q411,Q412 Q323,Q324 Q325,Q326 D451 D151,D201,D202,D301-D306 D309-D314 M5220P NJM78M15FA NJM79M05FA TA8409S TC9163AN UPC4570C 2SA1048 2SA970 2SA992 2SC1845 2SC1845 2SC2240 2SC2458 2SC2458 2SC2878 2SC4793 2SK1132 2SK1132 DTA114ES DTA124ES DTC124ES DTC143ES IRF540 IRF9540 D5SBA20 HSS104-02 HSS104-02
D307,D308 D456 D453 D455 D457-D460
COILS
L201,L202,L401,L403,L405,L406 BEADS FILTER L151-L154
RELAYS
RY401-RY403 RY101,RY102
CAPACITORS
C461 (1µF/100V) C457,C458 (3.3µF/25V) C451 (10000µF/43V) C452 (10000µF/43V) C101,C102,C105,C106 C109,C110,C113,C114 C153,C154 C303,C304 C313-C316 C163,C164 C103,C104 C167,C168 C408 C155,C156,C465 C169,C170 C459,C460 C307,C308 C467,C468
19
A-407R
Mark No. Description Part No.
CEAS470M25 CEAS471M6R3 CEBA100M50 CEBA100M50 CEBA2R2M50 CEBA3R3M50 CEBA470M50 CEBAR47M50 CEZA470M50 CFTYA224J50 CFTYA823J50 CKCYB222K50 CKCYB332K2H CKCYF473Z50 CKCYF473Z50 CKPUYB102K50 CQMA243J50 RD1/4LMF2R2J RD1/4MUF101J RD1/4MUF101J RD1/4MUF221J RD1/4MUF391J RD1/4MUF4R7J RD1/4MUF821J RD1/4PMF100J RD1/4PMF222J RD1/4PMF470J RD1/4PMF4R7J RD1/4PU100J RD1/4PU472J RDR1/2PM152J RDR1/4PM561J RFA1/4PS101J RN1/4PC2001F RS1LMF330J RS1LMFR22J RS2LMF122J RS2LMF331J VCP1123 RD1/4PU J 51063-0305 9604S-21C ABA-298 ABA1007 ABA1052 AKB7023 AKE1011 ANH-697 ANH1021 D15A03-075-2651 KM200IB4 KM200TA19 KPE3 RKN1004 VEF1040
Mark No.
Description
Part No.
C251 C157,C158 C305,C306,C455,C456 C463,C464 C405-C407 C301,C302 C317,C318 C325,C326 C319,C320 C115,C116,C201,C321-C324 C161,C162,C470 C165,C166 C401-C404 C117,C118,C171,C310,C327 C409,C453,C454 C172-C174 C159,C160
B FRONT L ASSY
SEMICONDUCTORS
IC751 Q751,Q752 Q702,Q703 Q701,Q704-Q707 D702,D711 D701,D704-D706 UPC4570C 2SC1845 2SC2458 DTC124ES HSS104-02 SLR-342VCT31 ASG1034 ACH7027 CCCSL151J50 CEAS100M50 CEASR47M50 CEJAR10M50 CFTLA153J50 CKCYF473Z50 CKPUYB102K50 CKPUYF473Z16 RD1/4MUF101J ACS7016 RD1/4PU J 51063-0705 D15A07-200-2651 KPE15 GP1U28X
SWITCHES
S701-S704
CAPACITORS
C701 (3.3µF/25V) C753,C754 C751,C752,C755,C756 C759,C760 C761,C762 C757,C758 C765 C763,C764 C711
RESISTORS
R458,R459 R133,R134,R171,R172 R317,R318,R351-R354,R417 R339-R346 R331-R334 R452 R125,R126 R367,R368 R355,R356 R461 R361,R362 R462 R460 R363,R364 R315,R316 R357-R360 R349,R350 R451 R413-R416 R453 R403,R404 VR301,VR302 (2.2k) Other Resistors
RESISTORS
R771,R772 VR751,VR752 (30k) Other Resistors
OTHERS
CABLE HOLDER (7P) J3 JUMPER WIRE CN701 CONNECTOR (15P) REMOTE RECEIVER UNIT
C VOLUME ASSY
SEMICONDUCTORS
Q501-Q510 Q512 Q511,Q513,Q514 D501-D510,D512,D513 2SK246 DTA124ES DTC124ES HSS104-02 CCCSL471J50 CEBA470M10 CFTYA823J50 CKCYF473Z50 ACX1090 RD1/4PU KP200TA19L KPE7
CAPACITORS
C501,C502 C512 C503,C504 C511
OTHERS
CABLE HOLDER (3P) CN202 21P FFC CONNECTOR SCREW SCREW SCREW CN101,CN102 PIN JACK(8P) SPEAKER TERMINAL 8-P HEAT SINK M HEAT SINK B J2 JUMPER WIRE CN204 CN203 CN401 JA401 4P PLUG 19P PLUG CONNECTOR (3P) REMOTE CONTROL JACK PCB BINDER
RESISTORS
VR501 (50k) Other Resistors J
OTHERS
CN501 19P SOCKET CN502 CONNECTOR (7P)
KN101,KN201,KN301,KN302,KN451 VNF1084 EARTH METAL FITTING
20
A-407R
Mark No. Description Part No. Mark No. Description Part No.
D FRONT R ASSY
SEMICONDUCTORS
IC601 IC603 IC602 Q609 Q607,Q610,Q618 Q612,Q613,Q615,Q616 Q601-Q606,Q608,Q614,Q617 D608-D610,D615,D618-D622 D636 D631 D617 D607 D601-D606,D632-D635 PD5369A TC74HC00AP TC74HC107AP 2SA1048 2SC2458 DTA124ES DTC124ES HSS104-02 HSS104-02 MTZJ2.2B MTZJ4.3A SLR-342DCT31 SLR-342VCT31 LAU221J ASG1034 ASX7002 ACH7027 ACH7058 CEJA1R0M50 CEJA2R2M50 CEJA470M16 CKCYF103Z50 CKPUYF103Z25 CKPUYF103Z25 CKPUYF473Z16 ACS7014 RD1/4PU VSS1014 51063-1505 9604S-21F D15A15-125-2651
CAPACITORS
C801,C802 (0.01µF/AC250V) C815 (3.3µF/25V) C813 C814 C811 ACG7020 ACH7027 CEAT471M25 CEBA470M10 CEYANP1R0M50 RD1/4PU ADX7207 AKP1034 AKP7005 KPE3 RKR1003 J
RESISTORS
All Resistors
OTHERS
Y802,Y803 BOARDIN READ WIRE CN802 AC SOCKET 1P CN801 AC INLET CN803 CONNECTOR (3P) H1,H2 FUSE HOLDER
COILS
L601-L608
F
HEADPHONE ASSY
C551,C552 CKCYB392K50 51063-0305 D15A03-150-2651 RKN1002
SWITCHES
S603,S604,S606 S601
CAPACITORS OTHERS
CABLE HOLDER (3P) J5 JUMPER WIRE JA501 HEADPHONE JACK
CAPACITORS
C601,C625,C635 (3.3µF/25V) C605 (0.22F) C624 C610,C637 C603 C604 C609,C613-C623,C626,C627 C632-C634 C628,C629,C631
G POWER SW ASSY
SWITCH
S901 ASG1035 ACG7017
RESISTORS
VR601 (500K) Other Resistors J
CAPACITOR
C901 (0.0033µF/AC250V)
OTHERS
CERAMIC RESONATOR (4.19MHz) CABLE HOLDER (15P) CN601 21P FFC CONNECTOR J4 JUMPER WIRE X601
E
Mark
AC PRIMARY ASSY
(1) CONTRAST TABLE
AWX7051 and AWX7056 are constructed the same except for the following :
Symbol and Description CN802 AC SOCKET 1P Part No. AWX7051 AWX7056 AKP1034 Not used Remarks
(2) PARTS LIST FOR AWX7051 SEMICONDUCTORS
IC811 Q811 D815 D811-D814 NJM78M56FA 2SK1132 HSS104-02 S5688G ATT7009 RSR1037
TRANSFORMER
T801
RELAY
RY801
21
A-407R
6. ADJUSTMENTS
6.1 IDLE CURRENT ADJUSTMENT
¶ CAUTION : Heatsinks' (Q323Q326) DC level is equal to +B or -B. Don't touch them or you will be electricary chocked. 1. Connect the measuring instrument as Fig.6-1. (R415 or R416) 2. Set the VOLUME CONTROL to minimum, BASS TONE CONTROL to center, TREBLE TONE CONTROL to center and BALANCE CONTROL to center. Set VR301 and VR302 to minimum. 3. Set the POWER switch to ON. 4. Adjust VR301 (VR302) so that the voltage between both sides of R415 (R416) becomes 16mV±1mV. (Within 10 seconds from when the relay is turned ON) 5. Ages for 7 minutes. 6. Adjust VR301 (VR302) so that the voltage between both sides of R415 (R416) becomes 11mV±1mV.
DC Voltmeter
DC Voltmeter
AF ASSY
SIDE A
R415 R413 W150 Heat Sink VR301 R417 W212
R416 R414
Heat Sink
VR302 Heat Sink
Heat Sink
CN204
Fig.6-1 Adjustment Method
22
A-407R
7. GENERAL INFORMATION
7.1 IC INFORMATION
PD5369A (FRONT R ASSY : IC601)
· REMOTE CONTROL AMP MICROCOMPUTER
· The information shown in the list is basic information and may not correspond exactly to that shown in the schematic diagrams.
· Pin Assignment (Top view)
P53 P17/SRDY P16/CLK P15/SOUT P14/SIN P13/T1 P12/T0 P11 P10 P27/IN7 P26/IN6 P25/IN5 P24/IN4 P23/IN3 P22/IN2 P21/IN1 P20/IN0 VREF XIN XOUT
1 SR 2 STB 3 CLK 4 DATA 5 CD-IND 6 TU-IND 7 PH-IND 8 LI-IND 9 T1-IND 10 SPA-IND 11 SPB-IND 12 LOU-IND 13 POW-IND 14 MUT-IND 15 DIR-IND 16 T2-IND 17 F-MUTE 18 VREF 19 XIN 20 XOUT 21 VSS
T2 42 POWER 41 LOUD 40 M-CTRL 39 P-DET 38 P-CTRL 37 DIRECT 36 MUTE 35 WAKE UP 34 FUNC2 33 FUNC1 32 V-UP 31 V-DOWN 30 RSEL2 29 RSEL1 28 NC 27 BACK UP 26 RST 25 SPA 24 SPB 23 VCC 22
P52 P07 P06 P05 P04 P03 P02 P01 P00 P43 P42 P41 P40 P33/CNTR1 P32/CNTR0 P31/INT1 P30/INT0 RESET P51/XCOUT P50/XCIN VCC
· Pin Function
VSS
No. Pin name I/O Function 1 P53 I Remote control signal input pin. 2 O STB for TC9163N. P17/SRDY 3 P16/CLK O CLOCK for TC9163N. 4 P15/SOUT O DATA for TC9163N. 5 P14/SIN O CD INDICATOR. 6 P13/T1 O TUNER INDICATOR. 7 P12/T0 O PHONO INDICATOR. 8 P11 O LINE INDICATOR. 9 P10 O TAPE1 INDICATOR. 10 P27/IN7 O SPEAKER-A INDICATOR. 11 P26/IN6 O SPEAKER-B INDICATOR. 12 P25/IN5 O LOUDNESS INDICATOR. 13 P24/IN4 O POWER (STAND-BY) INDICATOR. MUTE INDICATOR. 14 P23/IN3 O MUTE ON : Repeats H and L every 1 second. Normal : "H" 15 P22/IN2 O DIRECT INDICATOR. 16 P21/IN1 O TAPE2 INDICATOR. 17 P20/IN0 O FUNCTION switch MUTE. 18 VREF I Pulls up to 5V. 19 XIN I 4.19MHz . 20 XOUT O Ceramic vibrating and connecting terminal. 21 VSS - Digatal GND. 22 VCC - Power supply +5V. 23 P50/XCIN I SPEAKER-B KEY input.
No. Pin name I/O Function 24 P51/XCOUT I SPEAKER-A KEY input. 25 I Reset pin. RESET 26 P30/INT0 I BACK UP detection pin. interrupt specification. 27 P31/INT1 O Not used. 28 P32/CNTR0 I REC selector input 1. 29 P33/CNTR1 I REC selector input 2. interrupt specification. 30 P40 O Volume DOWN data output. 31 P41 O Volume UP data output. 32 P42 I FUNCTION selector input 1. 33 P43 I FUNCTION selector input 2. WAKE UP input. I 34 P00 Key on wake up specification. MUTE KEY input. I 35 P01 Key on wake up specification. DIRECT KEY input. I 36 P02 Key on wake up specification. 37 P03 O Protection control pin. 38 P04 I Output error detection pin 39 P05 O MUTING control pin. LOUDNESS KEY input. I 40 P06 Key on wake up specification. POWER KEY input. I 41 P07 Key on wake up specification. 42 P52 I TAPE2 KEY input.
23
24 ON/OFF
A-407R
A C
FUNCTION LOUDNESS Q505 Q501 Q503 DIRECT ON/OFF
CN101 CN102
RIAA
A
DIRECT ENERGY MOS
IC151
2.8mV /50k
PHONO
37dB
TUNER
C C
VOLUME
CD
7.2 BLOCK DIAGRAM
200mV /50k
LINE IC101(1/2)
C
Q509 Q303
A
M VR501
TONE AND BALANCE
C
Q507
POWER AMP WRLC 40dB PROTECTION RY A 401 RY401 SP-A A RY402 SP-B RY403 H.P A
TAPE1 /DAT SOURSE
F
JA501
200mV /1k
REC
A A
IC251 UP/DOWN
200mV TAPE2 /50k MONITOR
IC101(2/2)
B D
IC751 VR751 VR752 VR601
UNUSUAL OUTPUT FUNC DETECTION MUTE
200mV /1k
REC
CD, TAPE1/DAT : RY101, RY102
+BL TO FUNCTION SW TO POWER STAGE BL
A A
D451
FROM UNUSUAL OUTPUT DETECTION
A
DIRECT, LOUDNESS ON/OFF VOLUME UP/DOWN TO VOLTAGE STAGE MUTE, FUNC MUTE ON/OFF BH TO OP AMP RY
IC451 IC452
+19.2 15 +BH
KEY INPUTS
E
E
T1 FU1 RY801
G
S901
FROM REC SEL µ-COM
FROM FUNCTION SEL
D
IC601
A
TO µ-COM LED TO PROTECTION RY +5.6
D457-D460 T801
SR INPUT
E
IC811
E
D811-D814
A-407R
8. PANEL FACILITIES AND SPECIFICATIONS
8.1 REAR PANEL
Illustration shows U.K. model
1
2 3 4 5 6 7 89
0
-
#
European model only
AC OUTLET
SPEAKERS
SIGNAL GND
R
B
L
AC INLET
PHONO
TUNER
CD
LINE
TAPE1/MD REC PLAY
TAPE2 MONITOR REC PLAY
L R
IN IN IN IN OUT IN OUT IN
L
CONTROL OUT
SWITCHED 100W MAX
R R
A
L
@
!
~
=
1 PHONO terminals 2 SIGNAL GND (Turntable ground) terminal 3 TUNER terminals 4 CD terminals 5 LINE terminals 6 TAPE 1/MD REC (OUT) terminals 7 TAPE 1/MD PLAY (IN) terminals 8 TAPE 2 MONITOR REC (OUT) terminals
0 SPEAKERS B terminals (Right channel) - SPEAKERS B terminals (Left channel) = AC INLET jack
Connect one end of the power cord to here and the other end to an AC wall socket, or the AC outlet of an audio timer. If you are going to be away from home for a long period of time, disconnect the unit from the wall socket.
~ CONTROL OUT jack
This jack is for outputting control signals when operating other components bearing the Î mark with the amplifier's remote control unit.
! SPEAKERS A terminals (Left channel) @ SPEAKERS A terminals (Right channel) 9 TAPE 2 MONITOR PLAY (IN) terminals # AC OUTLET (European model only)
25
A-407R
8.2 FRONT PANEL
3
4
5
D
STANDBY/ON
STEREO AMPLIFIER
A-407R Direct Energy MOS
VOLUME TAPE 2
MONITOR
Î
STANDBY
CD
TUNER
PHONO
LINE
2 1
A
TAPE 1 /MD
POWER
OFF ON
6
B BASS TREBLE BALANCE INPUT SELECTOR REC SELECTOR
CD TUNER OFF SOURCE
SPEAKERS
@ !
PHONES
LOUDNESS
DIRECT
7
MIN
MAX
L
R
~
=
- 0
VOLUME indicator
9
8
1 POWER (
OFF/
ON) switch
5 INPUT SELECTOR knob/indicators
Turn the knob clockwise or counterclockwise so that the indicator lights for your desired input source. Turning the knob clockwise causes the lit indicator to right. Turning counterclockwise causes it to left. CD : For compact disc playback with a CD player. TUNER : For AM or FM broadcast reception with a tuner. PHONO : For record playback with a turntable. LINE : Set to this position when listening to a program from a component connected to the LINE terminals. TAPE 1/MD : For playback with a cassette deck or MD recorder connected to the TAPE 1/MD terminals.
Press to turn power to the unit ON and OFF.
2 STANDBY/ON switch/indicator
This is the switch for electric power. This switch does not function unless the POWER ON switch is set to ON. : When set to the ON position, power is supplied and the unit becomes operational. STANDBY : When set to the STANDBY position, the main power flow is cut and the unit is no longer fully operational. A minute flow of power feeds the unit to maintain operation readiness. When the STANDBY indicator lights, the unit is in STANDBY. NOTE: When performing timer recording with this unit, be sure to set the POWER STANDBY/ON switch to ON. ON OFF/
6 TAPE 2 MONITOR button/indicator
Use when there is an adaptor component (graphic equalizer, etc.) or cassette deck connected to the TAPE 2 MONITOR terminals. Off : Indicator goes out when not in use. On : Indicator lights when using the adaptor component or listening to the cassette deck. NOTE: When no connections are made to the TAPE 2 MONITOR terminals, or when they are not in use, be sure to set this switch to the off position. (No sound will be heard if it is set to the on position.)
3 Remote control sensor window 4 VOLUME control
Use to adjust the volume level. NOTE: The TONE effect functions regardless of volume levels.
26
A-407R
7 REC SELECTOR switch /indicator(For TAPE 1/MD
terminals)
This switch is used to select the recording source component. The signal from the selected component is output at the TAPE1/ MD jacks for recording. To select a recording source component, press the REC SELECTOR switch so that the indicator of the desired source component lights up. When this switch is set to [TUNER] or [CD], the signal from the selected component can be recorded regardless of the input selector switch and TAPE2 MONITOR button settings. : To record from the equipment connected to the CD terminals. TUNER : To record from the equipment connected to the TUNER terminals. SOURCE : To record from the equipment selected by the INPUT SELECTOR knob. OFF : In this position, nothing from the REC terminals of TAPE 1/MD is output. Set to this position when not recording; the cassette deck will be disconnected, improving sound quality. CD
- TREBLE tone control
Use to adjust the high-frequency tone. The center position is the flat (normal) position. When turned to the right, the high-frequency tone is emphasized; when turned to the left, the high-frequency tone is de-emphasized. NOTE: This control does not operate when the DIRECT button is in the on position.
= BASS tone control
Use to adjust the low-frequency tone. The center position is the flat (normal) position. When turned to the right, the low-frequency tone is emphasized; when turned to the left, the low-frequency tone is de-emphasized. NOTE: This control does not operate when the DIRECT button is in the on position.
~ PHONES jack
When using headphones, insert the plug into this jack.
NOTE: The function selected using the INPUT SELECTOR knob will be recorded irrespective of the position of the REC SELECTOR switch (TAPE 2 MONITOR terminals).
! SPEAKERS B (ON/OFF) button/indicator
Use this button to listen to the speaker system connected to the SPEAKERS B terminals. On : The indicator lights. Sound is heard from the speaker system. Off : The indicator goes out. No sound is heard from the speaker system. Set to this position when listening with headphones.
8 BALANCE control
Should normally be left in the center position. Adjust the balance if the sound is louder from one of the speakers. If the right side is louder, turn toward the L (left) position and if the left side is louder, turn toward the R (right) position. NOTE: This control does not operate when the DIRECT button is in the on position.
@ SPEAKERS A (ON/OFF) button/indicator
Use this button to listen to the speaker system connected to the SPEAKERS A terminals. On : The indicator lights. Sound is heard from the speaker system. Off : The indicator goes out. No sound is heard from the speaker system. Set to this position when listening with headphones.
9 DIRECT button/indicator
Use this button when you do not wish to pass the output from input terminal equipment through the various frequency adjusting circuits (BASS, TREBLE, BALANCE, LOUDNESS). On : The indicator lights. The signals input through the input terminals are reproduced without passing through the various frequency adjusting circuits. This results in flat, pure sound which is a more faithful reproduction of the input source. Off : The indicator goes out. The signal passes through the various frequency adjusting circuits.
0 LOUDNESS button/indicator
Use when listening at low volume level. On : The indicator lights. Boosts low and high frequencies to give added punch to playback even at low volume level. Off : The indicator goes out. Should normally be left in this position. NOTE: This button does not operate when the DIRECT button is in the on position.
27
A-407R
8.3 REMOTE CONTROL
1 2 3 4 5 6 7
STANDBY / ON AMP CD TUNER TAPE
8 9
TAPE SELECT
2
DECK II
7
3
DECK I
1 TAPE ¡ 7 3
0 = ~
4
DISC SELECT
¢
CD
_
STATION
+
TUNER
CD
TUNER
PHONO
+
VOLUME
TAPE 1
TAPE 2
LINE
STEREO AMPLIFIER REMOTE CONTROL UNIT
Î
1 CD POWER button
Switches CD player power STANDBY/ON.
8 TUNER POWER button
Switches TUNER power STANDBY/ON.
2 AMP POWER button
Switches the amplifier power STANDBY/ON.
9 TAPE POWER button
Switches the cassette deck power STANDBY/ON.
3 TAPE SELECT button
Selects the cassette No. (1 to 6) for a multi-cassette changer.
0 TAPE operation buttons
2, 3 : Playback in the direction of the arrows. 7 : Stop 1, ¡ : Tape fast forward/reverse.
4 DECK II button
To operate Deck II, press this button before pressing the operating buttons. Also, when using a single deck, press this button before pressing the operating buttons.
- CD player operation buttons
4 ¢ 7 3 : Returns you to the start of the current track (Track search). : Takes you to the start of the next track (Track search). : Stop : Play
5 DECK I button
To operate Deck I, press this button before pressing the operating buttons.
6 DISC SELECT button
Press this to select discs on a multi or twin tray compact disc player.
= STATION +, buttons (TUNER)
Calls each station number in sequence.
7 Input selector buttons
Use to select the playback source. CD : For compact disc playback with a CD player. TUNER : For AM or FM broadcast reception with a tuner. PHONO : For record playback with a turntable. TAPE 1 : For playback with a cassette deck or MD recorder connected to the TAPE 1/MD terminals. TAPE 2 : For playback with a cassette deck or adaptor connected to the TAPE 2 MONITOR terminals. LINE : For playback with a component connected to the LINE terminal.
~ VOLUME +, buttons
+ ........................................................... Increases the volume.
......................................................... Decreases the volume.
NOTE: When the accessory remote control unit is used to operate other PIONEER components with the Î mark, it cannot be used to operate functions which do not correspond to the functions listed on the remote control unit.
28
A-407R 8.4 SPECIFICATIONS
Amplifier Section
Continuous power output (both channels driven at 20 Hz to 20 kHz)** T.H.D. 0.06 %, 8 ............................................. 45 W + 45 W* T.H.D. 0.09 %, 4 ............................................. 65 W + 65 W* DIN Continuous power output (both channels driven at 1 kHz) T.H.D. 1.0 %, 8 ................................................. 60 W + 60 W T.H.D. 1.0 %, 4 ................................................. 90 W + 90 W Total harmonic distortion** 20 Hz to 20 kHz, 20 W, 8 .......................................... 0.06 %* Signal-to-Noise ratio (IHF short circuit, A network) PHONO (MM, 5 mV input) .............................................. 86 dB* CD, TUNER, LINE, TAPE 1/MD, TAPE 2 MONITOR ....................................................... 106 dB* Signal-to-Noise ratio (DIN, continuous power/ 50 mW) PHONO (MM) ..................................................... 71 dB/ 67 dB* CD, TUNER, LINE, TAPE 1/MD, TAPE 2 MONITOR ............................................. 95 dB/ 71 dB*
Power Supply/ Miscellaneous
Power requirements ......................... AC 220 - 230 Volts, 50/ 60 Hz Power consumption ........................................................................................ 160 W AC outlet(European model only) Switched(x1) ....................................................................... 100W Dimensions (including knobs and other protruding parts) ............................................... 420 (W) × 335 (D) × 128 (H) mm Weight (without package) ......................................................................................... 6.9 kg
· Power output specification is for when power supply is 230V.
Input sensitivity/ impedance PHONO (MM) ..................................................... 2.8 mV/ 50 k CD, TUNER, LINE, TAPE 1/MD, TAPE 2 MONITOR ............................................ 200 mV/ 50 k PHONO (MM) overload level 1 kHz, T.H.D. 0.1 % ...................................................... 150 mV Output level/ impedance TAPE 1/MD, TAPE 2 MONITOR output ............................................................................. 200 mV/ 1 k Frequency response PHONO (MM) .................................... 20 Hz to 20 kHz ± 0.5 dB CD, TUNER, LINE, TAPE 1/MD, TAPE 2 MONITOR .............................. 5 Hz to 100 kHz +0 dB* -3 Tone control BASS ............................................................... ± 8 dB (100 Hz) TREBLE ............................................................ ± 8 dB (10 kHz) Loudness contour (volume control set at 30 dB position) .............................................. + 5 dB (100 Hz)/ + 3 dB (10 kHz)
Accessories
Remote control unit ........................................................................ 1 Batteries (AA/R6P) ......................................................................... 2 Operating instructions .................................................................... 1 Power cord(Rated current 2.5 A) ................................................... 1
NOTE: Specifications and design subject to possible modification without notice, due to improvements.
* Measured with the DIRECT button set to on. ** Measured by Audio Spectrum Analyzer.
· ACCESSORIES
STANDBY / ON AMP CD
TUNER
TAPE
TAPE SELECT
2
DECK II
7
3
DECK I
1 TAPE ¡ 7 3
4
DISC SELECT
¢
CD
_
STATION
+
TUNER
CD
TUNER
PHONO
+
VOLUME
Remote control unit (CU-A013) (AXD7164)
TAPE 1
TAPE 2
LINE
STEREO AMPLIFIER REMOTE CONTROL UNIT
Î
Power cord (ADG1154) MY/EW and MY/GR types
Power cord with fuse (ADG1156) MV type
Batteries (AA/R6P) (AEX-010)
29