Text preview for : Pioneer-M10X pwramp.pdf part of Pioneer M10X power amplifier
Back to : Pioneer-M10X pwramp.pdf | Home
STEREO POWER AMPLIFIER
v¿,?m
Î
STANDBY
STANDBY/ON
POWER
OFF ON
REFERENCE STEREO POWER AMPLIFIER
ORDER NO.
The illustration shows the KU/CA type
RRV2382
STEREO POWER AMPLIFIER
M-10X
THIS MANUAL IS APPLICABLE TO THE FOLLOWING MODEL(S) AND TYPE(S).
Type
KU/CA MY
Model M-10X
AC120V AC220230V
Power Requirement
Remarks
CONTENTS
1. SAFETY INFORMATION .................................... 2 2. EXPLODED VIEWS AND PARTS LIST ............. 3 3. BLOCK DIAGRAM AND SCHEMATIC DIAGRAM ......................................................... 6 4. PCB CONNECTION DIAGRAM ....................... 12 5. PCB PARTS LIST ............................................. 16 6. ADJUSTMENT .................................................. 19 PIONEER CORPORATION 7. GENERAL INFORMATION .............................. 20 7.1 IC ................................................................ 20 7.2 CIRCUIT DESCRIPTION ........................... 21 8. PANEL FACILITIES AND SPECIFICATIONS .................................................................... 21
4-1, Meguro 1-chome, Meguro-ku, Tokyo 153-8654, Japan PIONEER ELECTRONICS SERVICE, INC. P.O. Box 1760, Long Beach, CA 90801-1760, U.S.A. PIONEER EUROPE NV Haven 1087, Keetberglaan 1, 9120 Melsele, Belgium PIONEER ELECTRONICS ASIACENTRE PTE. LTD. 253 Alexandra Road, #04-01, Singapore 159936
PIONEER CORPORATION 2000
TZZA SEPT. 2000 Printed in Japan
M-10X
1. SAFETY INFORMATION
This service manual is intended for qualified service technicians; it is not meant for the casual do-it-yourselfer. Qualified technicians have the necessary test equipment and tools, and have been trained to properly and safely repair complex products such as those covered by this manual. Improperly performed repairs can adversely affect the safety and reliability of the product and may void the warranty. If you are not qualified to perform the repair of this product properly and safely, you should not risk trying to do so and refer the repair to a qualified service technician.
WARNING This product contains lead in solder and certain electrical parts contain chemicals which are known to the state of California to cause cancer, birth defects or other reproductive harm. Health & Safety Code Section 25249.6 Proposition 65
NOTICE (FOR CANADIAN MODEL ONLY) Fuse symbols (fast operating fuse) and/or (slow operating fuse) on PCB indicate that replacement parts must be of identical designation. REMARQUE (POUR MODÈLE CANADIEN SEULEMENT) Les symboles de fusible (fusible de type rapide) et/ou (fusible de type lent) sur CCI indiquent que les pièces de remplacement doivent avoir la même désignation.
(FOR USA MODEL ONLY) 1. SAFETY PRECAUTIONS
The following check should be performed for the continued protection of the customer and service technician.
LEAKAGE CURRENT CHECK
Measure leakage current to a known earth ground (water pipe, conduit, etc.) by connecting a leakage current tester such as Simpson Model 229-2 or equivalent between the earth ground and all exposed metal parts of the appliance (input/output terminals, screwheads, metal overlays, control shaft, etc.). Plug the AC line cord of the appliance directly into a 120V AC 60 Hz outlet and turn the AC power switch on. Any current measured must not exceed 0.5 mA.
ANY MEASUREMENTS NOT WITHIN THE LIMITS OUTLINED ABOVE ARE INDICATIVE OF A POTENTIAL SHOCK HAZARD AND MUST BE CORRECTED BEFORE RETURNING THE APPLIANCE TO THE CUSTOMER.
2. PRODUCT SAFETY NOTICE
Many electrical and mechanical parts in the appliance have special safety related characteristics. These are often not evident from visual inspection nor the protection afforded by them necessarily can be obtained by using replacement components rated for voltage, wattage , etc. Replacement parts which have these special safety characteristics are identified in this Service Manual. Electrical components having such features are identified by marking with a on the schematics and on the parts list in this Service Manual. The use of a substitute replacement component which does not have the same safety characteristics as the PIONEER recommended replacement one, shown in the parts list in this Service Manual, may create shock, fire, or other hazards. Product Safety is continuously under review and new instructions are issued from time to time. For the latest information, always consult the current PIONEER Service Manual. A subscription to, or additional copies of, PIONEER Service Manual may be obtained at a nominal charge from PIONEER.
Device under test
Test all exposed metal surfaces
Leakage current tester
Reading should not be above 0.5 mA
Also test with plug reversed (Using AC adapter plug as required) Earth ground
AC Leakage Test
2
M-10X
2. EXPLODED VIEWS AND PARTS LIST
NOTES : Parts marked by " NSP " are generally unavailable because they are not in our Master Spare Parts List. The mark found on some component parts indicates the importance of the safety factor of the part. Therefore, when replacing, be sure to use parts of identical designation. Screws adjacent to mark on the product are used for disassembly.
KU/CA type 15 MY type Only 4 MY type 15 12
2.1 PACKING
(1) PACKING PARTS LIST
Mark No.
1 2 3 NSP 4 5 6 7 8 9 10 11 12 13 14 15
Description
Operating Instructions .................................... .................................... Warranty Card .................................... .................................... .................................... Side Protector L Side Protector R .................................... Packing Case Literature Bag Packing Sheet Remote Control Cord Power Cord
Part No.
See Contrast table (2)
14 1 13 4
Separate
See Contrast table (2)
8
FR ON T
KU/CA type Only
Separate
AHA7127 AHA7128 See Contrast table (2) AHG117 AHG1016 PDE1247 See Contrast table (2)
NSP
9
11
(2) CONTRAST TABLE
M-10X/KU/CA and MY are constructed the same except for the following:
Mark No.
1 1
Symbol and Description KU/CA type
Operating Instructions (English) Operating Instructions (English/French/German/Italian/ Dutch/Swedish/Spanish/Portuguese) Warranty Card Packing Case Power Cord ARC7331 Not used
Part No. MY type
Not used ARC7332
Remarks
NSP
4 11 15
ARY1026 AHD7946 ADG7021
ARY7022 AHD7947 ADG1154
ACCESSORIES
Black Operating Instructions (ARC7331: KU/CA type) (ARC7332: MY type) Warranty Card
Power cord (ADG7021) (For KU/CA type)
Power cord (ADG1154) (For MY type)
Remote Control Cord (PDE1247) (L= 1 m)
3
M-10X
2.2 EXTERIOR
36 39
39
42
42 42
39 44 MY type Only 47 41 44 3 44 43 44 1 KU/CA type Only 6 26 10 A 15 MY type Only KU/CA type Only 8 15 49 26 39 31
D F
2
C
4
24
37 5 27 44
15 45 15
B E
38 32 9 43 17 11 45 16 19 26
45 15 15 45 17 13 20 48 16 42 42 7 45 45 15
30
A
35
18
17
40 A 42 29 23 51 50 KU/CA type Only 23 23
42
23
12
33
33
22 14 29
34 33 46 28 26 21 25 14 28 26
4
M-10X
(1) EXTERIOR SECTION PARTS LIST
Mark No.
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25
Description
FRONT L Assy FRONT R Assy POWER SW Assy AC PRIMARY Assy LED Assy Fuse (15A) AF Assy Fuse Flexible Cable (J1, 21P) (AF CN202 FRONT R CN601) Fuse Holder Power Transformer (T1) Chassis Rear Panel Insulator Screw Screw Screw (4×12) Lens Assy PCB Mold Barrier PCB Holder Stud Cover PCB Mold Radiator Plate L Locking Card Spacer
Part No.
AWX7766 AWX7768 AWX7057 See Contrast table (2) AWX7770 See Contrast table (2) See Contrast table (2) See Contrast table (2) ADD1114 See Contrast table (2) See Contrast table (2) ANA7048 See Contrast table (2) PNW2766 ABA1018 ABA1050 ABA1014 AEC7321 AMR7222 AEC7072 AEC7057 AEC7096 AMR1525 AMR7341 DEC1908
Mark No.
26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51
Description
Screw PVC Cover Cushion 55 Rubber Cushion Name Plate 65 Label LED Lens Spacer Sub Flame Main Power Button Bonnet Case Panel Base Front Panel Screw Trans Plate Power Button Screw Screw Screw Washer Screw Top Cover Washer Fuse Card Fuse Card Fuse Caution Label
Part No.
BBZ30P080FCC See Contrast table (2) PNM1316 AEB7004 See Contrast table (2) See Contrast table (2) PNW2019 ABF7004 ANG7137 See Contrast table (2) See Contrast table (2) See Contrast table (2) See Contrast table (2) See Contrast table (2) ANG7228 See Contrast table (2) BBT30P080FCC BBZ30P060FCC BPZ30P080FMC WG40FCC ABA1193 See Contrast table (2) AEE7027 See Contrast table (2) See Contrast table (2) See Contrast table (2)
NSP
NSP
NSP
NSP NSP NSP
NSP NSP NSP
(2) CONTRAST TABLE
M-10X/KU/CA and MY are constructed the same except for the following:
Mark No.
4 6 7 8 10 11 13 27 30 31 35 36 37 38 39 41 47 49 50 51
Symbol and Description KU/CA type
AC PRIMARY Assy Fuse (15A) AF Assy Fuse Fuse Holder Power Transformer (T1) Rear Panel PVC Cover Name Plate 65 Label Main Power Button Bonnet Case Panel Base Front Panel Screw Power Button Top Cover Fuse Card Fuse Card Fuse Caution Label AWX7771 AEK7070 AWX7776 REK1085 (6.3A/125V) AKR1005 ATS7298 ANC7982 AAK7845 PAN1376 ARW7050
Part No. MY type
AWX7056 Not used AWX7767 REK1025 (T2AL250V) Not used ATS7297 ANC7983 AAK7844 PAN1377 Not used AAD7596 ANE7264 AMB7735 ANB7252 BBT30P080FNI AAD7446 AME7371 Not used Not used Not used
Remarks
AAD7437 ANE7185 AMB7736 ANB7255 BBT30P080FZK AAD7436 Not used AAX1180 AAX7832 AAX7831
NSP NSP NSP
5
1
2
3
4
M-10X
3. BLOCK DIAGRAM AND SCHEMATIC DIAGRAM
3.1 BLOCK DIAGRAM AND OVERALL SCHEMATIC DIAGRAM
A
(J4)
E B
LED ASSY (AWX7770)
FRONT R ASSY (AWX7768)
B
CN401
A
C
AF ASSY (AWX7776: KU/CA type) (AWX7767: MY type)
DIRECT ENERGY MOS POWER AMP
POWER AMP WRLC 29dB
R413
CN202
CN601
(J5)
(J2)
JA101
0.7V/50 k
IC451 +19.4V
CN204
D
15V D457D460
6
1 2 3 4
5
6
7
8
M-10X
Note: When ordering service parts, be sure to refer to "EXPLODED VIEWS AND PARTS LIST" or "PCB PARTS LIST".
CN701
A
F
FRONT L ASSY (AWX7766)
· NOTE FOR FUSE REPLACEMENT
CAUTION -
FOR CONTINUED PROTECTION AGAINST RISK OF FIRE. REPLACE WITH SAME TYPE AND RATINGS OF FUSE.
MY type
AC POWER CORD ADG1154
B
C
AC PRIMARY ASSY (AWX7771: KU/CA type) (AWX7056: MY type) CN801
KU/CA type MY type
KU/CA type
AC POWER CORD ADG7021
CN803
D
POWER SW ASSY (AWX7057)
C
Description:
Power amplifier part Revise a wide range linear circuit of A-504R series (WRLC), and this circuitry uses MOS-FET for power output stage without source resistance.
MY type
Power amplifier part Power supply unit consists of main transformer and sub transformerfor u-COM. Secondary side of main transformer is divided for DIRECT ENERGY MOS AMP by 2 circuit.
D
KU/CA type
250V
7
5 6 7 8
1
2
3
4
M-10X 3.2 AF and LED ASSYS
CN204 CN202
E
CN601
A
A
AF ASSY (AWX7776: KU/CA type) (AWX7767: MY type)
B
INPUT
51k
51k
C
JA101
D
8
A
1
2
820k
820k
3
4
5
6
7
8
M-10X C
J2 JA401
CN803
: Audio Signal Route (L ch)
A
B
MY type Only
A
C
SPEAKER TERMINAL 4-P VKE1002 (KU/CA type) VKE1003 (MY type)
CN401
To SPEAKER
D
J5
B
5 6
LED ASSY (AWX7770)
7
A B
8
9
1
2
3
4
M-10X 3.3 AC PRIMARY, POWER SW, FRONT R and FRONT L ASSYS
· NOTE FOR FUSE REPLACEMENT
CAUTION A
FOR CONTINUED PROTECTION AGAINST RISK OF FIRE. REPLACE WITH SAME TYPE AND RATINGS OF FUSE.
C
AC PRIMARY ASSY (AWX7771: KU/CA type) (AWX7056: MY type)
6.3A/125V REK1085 (KU/CA) T2AL250V REK1025 (MY)
CN803
A
J2
CN801
B
E
FRONT R ASSY (AWX7768)
C
D
10
C E
1
2
3
4
5
6
7
8
M-10X
A
S901: POWER SW
MY type
D
POWER SW ASSY (AWX7057)
A
250V
B
KU/CA type
· NOTE FOR FUSE REPLACEMENT
CN601
CAUTION -
FOR CONTINUED PROTECTION AGAINST RISK OF FIRE. REPLACE WITH SAME TYPE AND RATINGS OF FUSE.
A
CN202
C
J4
CN701
D
F
FRONT L ASSY (AWX7766)
5
6
7
D E F
8
11
1
2
3
4
M-10X
4. PCB CONNECTION DIAGRAM
A
A
Rear
AF ASSY
4.1 AF and LED ASSYS SIDE A
To POWER TRANSFORMER T1
C CN803
B
NOTE FOR PCB DIAGRAMS:
1. Part numbers in PCB diagrams match those in the schematic diagrams. 2. A comparison between the main parts of PCB and schematic diagrams is shown below.
Symbol in PCB Diagrams Symbol in Schematic Diagrams Part Name
B B C E B B C E
C
E B
C
E Transistor
C
E B
C
E Transistor with resistor
D D G S
G
S D
G
S Field effect transistor
Resistor array
C
3-terminal regulator 3. The parts mounted on this PCB include all necessary parts for several destination. For further information for respective destinations, be sure to check with the schematic diagram.
4. Viewpoint of PCB diagrams
Connector Capacitor
SIDE A
P. C. Board
Chip Part
SIDE B
B
D
LED ASSY
(ANP7377-A)
12
A B
1
2
3
4
5
6
7
8
M-10X
Q401
A
Q406
Q413
Q414
Q451 IC451 IC151 IC452 Q452
B
IC101 Q409 Q410 Q411 Q407 Q412 Q323 Q408 Q324
Q319 Q101 Q322 Q104 VR301 VR302 Q313 Q318
Q151 Q153
C
Q309 Q312 Q325
Q334
E
IC301
CN601
Q301 Q304
D
IC251
Q251
(ANP7376-A)
5 6 7
A
8
13
1
2
3
4
M-10X 4.2 AC PRIMARY, POWER SW, FRONT R and FRONT L ASSYS
A
T1 POWER TRANSFORMER
MY type
A
B
KU/CA type
Rear
F
SIDE A
FRONT L ASSY
C
VR752 Q701 Q707 Q706 Q702 Q704 Q703 IC751 Q751 Q752
VR751
(ANP7376-A)
Q705
D
14
F
1
2
3
4
5
6
7
8
M-10X SIDE A
C
AC PRIMARY ASSY
D
NEUTRAL LIVE
POWER SW ASSY
A
KU/CA type MY type
B
(ANP7377-A)
Q811
IC811
(ANP7377-A)
A J2
E
FRONT R ASSY
C
D
VR601 Q611 Q607 Q614 Q615 Q613 Q601 Q612 Q602 Q603 Q604 IC601 Q605 Q608 Q609 IC602 IC603 Q618
(ANP7377-A)
Q610 Q617 Q606 Q616
A CN202
6 7
5
C D E
8
15
M-10X
5. PCB PARTS LIST
NOTES : ÷ Parts marked by " NSP " are generally unavailable because they are not in our Master Spare Parts List. mark found on some component parts indicates the importance of the safety factor of the part. ÷ The Therefore, when replacing, be sure to use parts of identical designation. ÷ When ordering resistors, first convert resistance values into code form as shown in the following examples. Ex. 1 When there are 2 effective digits (any digit apart from 0), such as 560 ohm and 47k ohm (tolerance is shown by J = 5%, and K = 10%). 560 = 56 × 10 1 = 561 ................................................... RD1/4PU 5 6 1 J 47k = 47 × 10 3 = 473 .................................................. RD1/4PU 4 7 3 J 0.5 = R50 ...................................................................... RN2H Â 5 0 K 1 = 1R0 ......................................................................... RS1P 1 Â 0 K Ex. 2 When there are 3 effective digits (such as in high precision metal film resistors). 5.62k = 562 × 10 1 = 5621 ........................................... RN1/4PC 5 6 2 1 F
LIST OF WHOLE PCB ASSEMBLIES
Part No. Mark
NSP
Symbol and Description KU/CA type
CONTROL ASSY POWER SW ASSY FRONT R ASSY LED ASSY AC PRIMARY ASSY AF COMPLEX ASSY FRONT L ASSY AF ASSY AWG7025 AWX7057 AWX7768 AWX7770 AWX7771 AWK7679 AWX7766 AWX7776
Remarks MY type
AWG7024 AWX7057 AWX7768 AWX7770 AWX7056 AWK7678 AWX7766 AWX7767
NSP
CONTRAST OF PCB ASSEMBLIES
C
AC PRIMARY Assy
Part No.
AWX7771 and AWX7056 are constructed the same except for the following:
Mark Symbol and Description AWX7771
CN801 Y801 Y803 AKP1122 ADX7207 Not used
Remarks AWX7056
AKP7005 Not used ADX7207
A
AF Assy
Part No.
AWX7776 and AWX7767 are constructed the same except for the following:
Mark Symbol and Description AWX7776
R1003 R1004R1006 Speaker Terminal 4-P Not used Not used VKE1002
Remarks AWX7767
RS3LMF391J RS3LMF471J VKE1003
16
M-10X
PCB PARTS LIST FOR KU/CA TYPE
Mark No. Description Part No. Mark No. Description Part No.
D POWER SW ASSY
SWITCHES AND RELAYS
S901 ASG1035
C AC PRIMARY ASSY
SEMICONDUCTORS
IC811 Q811 D815 D811D814 NJM78M56FA 2SK1132 HSS10402 S5688G
CAPACITORS
C901 (3300pF/250V) ACG7017
TRANSFORMERS
T801 ATT7009
E
FRONT R ASSY
IC601 Q609 Q610 Q612 Q608 D608D610, D615, D618D622 D636, D640D644 D617 PD5637A 2SA1048 2SC2458 DTA124ES DTC124ES HSS10402 HSS10402 MTZJ4.3A
SEMICONDUCTORS
SWITCHES AND RELAYS
RY801 RSR1037
CAPACITORS
C801, C802 (10000pF/250V) C815 (3.3µF/25V) C813 C814 C811 ACG7020 ACH7027 CEAT471M25 CEBA470M10 CEYANP1R0M50
RESISTORS
All Resistors RD1/4PU J
COILS AND FILTERS
L601, L602, L608 LAU221J
OTHERS CAPACITORS
C605 C610 C603 C604 C613, C620, C626 C628, C629 C609, C636 ACH7058 CEJA2R2M50 CEJA470M16 CKCYF103Z50 CKPUYF103Z25 CKPUYF473Z16 CKPUYX472M16 Y801, Y802 CN801 CN803 H1, H2 BOARDIN READ WIRE AC INLET (1P) CONNECTOR (3P) FUSE HOLDER ADX7207 AKP1122 KPE3 RKR1003
F
FRONT L ASSY
Q702 Q701 D711 D701 2SC2458 DTC124ES HSS10402 SLR343VC (NPQ)
SEMICONDUCTORS
RESISTORS
All Resistors RD1/4PU J
OTHERS
CN601 J4 X601 CABLE HOLDER (15P) 21P FFC CONNECTOR JUMPER WIRE (4.19MHz) 510631505 9604S21F D15A151252651 VSS1014
SWITCHES AND RELAYS
S701 VSG1009
CAPACITORS
C711 CKPUYF473Z16
B LED ASSY
SEMICONDUCTORS
D551 BR5064X
RESISTORS
All Resistors RD1/4PU J
OTHERS
CN701 CONNECTOR (15P) KPE15
OTHERS
J5 CABLE HOLDER (3P) JUMPER WIRE 510630305 D15A031502651
17
M-10X
Mark No.
Description
Part No.
Mark No.
Description
Part No.
CKCYF223Z50 CKCYF473Z50 PCH1128
A AF ASSY
SEMICONDUCTORS
IC451 IC452 IC301 Q152, Q327, Q328, Q409, Q410 Q321, Q322 Q311Q314, Q329, Q330 Q452 Q309, Q310, Q315, Q316 Q333, Q334 Q319, Q320 Q151, Q317, Q318, Q331, Q332 Q407, Q408 Q303, Q304 Q451 Q403 Q401 Q251 Q411, Q412 Q323, Q324 Q325, Q326 D451 D1000, D151, D201, D202 D301D306, D309D314 D307, D308 D454 D453 D455 D457D460 NJM78M15FA NJM79L15A UPC4570C 2SA1048 2SA970 2SA992 2SB1238X 2SC1845 2SC1845 2SC2240 2SC2458 2SC2458 2SC2878 2SC4793 2SK1132 DTA114ES DTC124ES DTC143ES IRF540A IRF9540A D5SBA20 HSS10402 HSS10402 HZS9A1L MTZJ33B MTZJ36B MTZJ4.7A S5688G
C407 C310, C327, C409, C453, C454 C307, C308 (220µF/25V)
RESISTORS
R363, R364 R458, R459 R317, R318, R351R354, R417 R452 R339R346 R331R334 R367, R368 R355, R356 R461 R361, R362 R462 R315, R316 R357R360 R349, R350 R451 R413R416 R453 R454 VR301, VR302 (2.2 k) Other Resistors RD1/2PMF152J RD1/4LMF2R2J RD1/4MUF101J RD1/4MUF101J RD1/4MUF221J RD1/4MUF391J RD1/4PMF100J RD1/4PMF222J RD1/4PMF470J RD1/4PMF4R7J RD1/4PU100J RDR1/4PM561J RFA1/4PS101J RN1/4PC2001F RS1LMF330J RS1LMFR22J RS2LMF122J RS2LMF182J VCP1123 RD1/4PU
J
OTHERS
CN202 CABLE HOLDER (3P) 21P FFC CONNECTOR SCREW SCREW (STEEL) SCREW HEAT SINK B HEAT SINK JUMPER WIRE PIN JACK (2P) 4P PLUG 510630305 9604S21C ABA298 ABA1007 ABA1052 ANH1021 ANH1150 D15A030752651 DKB1045 KM200IB4 KPE3 RKN1004 VEF1040 VKE1002 VNF1084
COILS AND FILTERS
L201, L202, L401, L405, L406 ATX1012
SWITCHES AND RELAYS
RY401 ASR7014
J2 JA101 CN204 CN401 JA401
CAPACITORS
C461 (1µF/100V) C301, C302, C457, C458 (3.3µF/25V) C451, C452 (15000µ/50V) C303, C304 C313C316 C408 C465, C466 C467, C468 C405 C325, C326 C305, C306, C455, C456, C463 C459, C460 C317C320 C201, C321C324 C470 ACH1237 ACH7027 ACH7157 CCCSL221K2H CCCSL330K2H CEANP470M10 CEAT100M50 CEAT2R2M2A CEBA2R2M50 CEBAR47M50 CENA100M50 CENA102M50 CENA470M50 CFTYA224J50 CFTYA823J50
CONNECTOR (3P) JACK PCB BINDER SPEAKER TERMINAL 4P KN101, KN201, KN301, KN302, KN451 EARTH METAL FITTING
18
M-10X
6. ADJUSTMENT
6.1 IDLE CURRENT ADJUSTMENT
CAUTION : Heatsinks' (Q323Q326) DC level is equal to +B or B. Don't touch them or you will be electricary chocked. Connect the measuring instrument as Fig.61. (R415 or R416) Set VR301 and VR302 to minimum. Set the POWER switch to ON. Adjust VR301 (VR302) so that the voltage between both sides of R415 (R416) becomes 16mV±1mV. (Within 10 seconds from when the relay is turned ON) 5. Ages for 7 minutes. 6. Adjust VR301 (VR302) so that the voltage between both sides of R415 (R416) becomes 11mV±1mV. 1. 2. 3. 4.
DC Voltmeter
DC Voltmeter
AF ASSY
SIDE A
R415 R413 W150 Heat Sink VR301 R417 W212
R416 R414
Heat Sink
VR302 Heat Sink
Heat Sink
CN204
Fig. 61 Adjustment Method
19
M-10X
7. GENERAL INFORMATION
7.1 IC
PD5604A ( IC601: FRONT R ASSY) Remote Control Amp Microcomputer
Pin Assignment (Top view)
P53 P17/SRDY P16/CLK P15/SOUT P14/SIN P13/T1 P12/T0 P11 P10 P27/IN7 P26/IN6 P25/IN5 P24/IN4 P23/IN3 P22/IN2 P21/IN1 P20/IN0 VREF XIN XOUT VSS
1 SR 2 STB 3 CLK 4 DATA 5 CD-IND 6 TU-IND 7 PH-IND 8 LI-IND 9 T1-IND 10 SPA-IND 11 SPB-IND 12 LOU-IND 13 POW-IND 14 MUT-IND 15 DIR-IND 16 T2-IND 17 F-MUTE 18 VREF 19 XIN 20 XOUT 21 VSS
· The information shown in the list is basic information and may not correspond exactly to that shown in the schematic diagrams.
T2 42 POWER 41 LOUD 40 M-CTRL 39 P-DET 38 P-CTRL 37 DIRECT 36 MUTE 35 WAKE UP 34 FUNC2 33 FUNC1 32 V-UP 31 V-DOWN 30 RSEL2 29 RSEL1 28 NC 27 BACK UP 26 RST 25 SPA 24 SPB 23 VCC 22
P52 P07 P06 P05 P04 P03 P02 P01 P00 P43 P42 P41 P40 P33/CNTR1 P32/CNTR0 P31/INT1 P30/INT0 RESET P51/XCOUT P50/XCIN VCC
Pin Function
No. Pin Name 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 P53 P17/SRDY P16/CLK P15/SOUT P14/SIN P13/T1 P12/T0 P11 P10 P27/IN7 P26/IN6 P25/IN5 P24/IN4 P23/IN3 P22/IN2 P21/IN1 P20/IN0 VREF XIN XOUT VSS VCC P50/XCIN I/O I O O O O O O O O O O O O O O O O I I O I TC9163N TC9163N TC9163N Description Remote control signal input pin. STB CLOCK DATA No. Pin Name 24 P51/XCOUT 25 26 27 RESET P30/INT0 P31/INT1 I/O I I I O I I O O I I I I I O I O I I I Reset pin. BACK UP detection pin. interrupt specification. Not used. REC selector input 1. REC selector input 2. interrupt specification. Volume DOWN data output. Volume UP data output. FUNCTION selector input 1. FUNCTION selector input 2. WAKE UP input. Key on wake up specification. MUTE KEY input. Key on wake up specification. DIRECT KEY input. Key on wake up specification. Protection control pin. Output error detection pin MUTING control pin. LOUDNESS KEY input. Key on wake up specification. POWER KEY input. Key on wake up specification. TAPE2 KEY input. Description SPEAKER-A KEY input.
CD INDICATOR TUNER INDICATOR PHONO INDICATOR LINE INDICATOR TAPE1 INDICATOR SPEAKER-A INDICATOR SPEAKER-B INDICATOR LOUDNESS INDICATOR POWER (STAND-BY) INDICATOR MUTE INDICATOR MUTE ON : Repeats H and L every 1 second. DIRECT INDICATOR TAPE2 INDICATOR FUNCTION switch MUTE. Pulls up to 5V. 4.19MHz Ceramic vibrating and connecting terminal. Digatal GND. Power supply +5V. SPEAKER-B KEY input.
28 P32/CNTR0 29 P33/CNTR1 30 31 32 33 34 35 36 37 38 39 40 41 42 P40 P41 P42 P43 P00 P01 P02 P03 P04 P05 P06 P07 P52
20
M-10X
7.2 CIRCUIT DESCRIPTION
Use a wide range linear circuit of A-607R series for voltage stage, and use HEX POWER MOSFET for output stage.
This circuitry eliminates source resistance, and reduce power loss in large amount with super low capacity resistor of output stage device and realize the low generation of heat, low source voltage. This circuitry eliminates source resistance and listing electric coil, and achieve the damping factor that is flat with band (20Hz - 20kHz).
B2 +B1 +B2
B1
8. PANEL FACILITIES AND SPECIFICATIONS
PANEL FACILITIES (The illustration shows the KU/CA type.)
2 3
STEREO POWER AMPLIFIER
v¿,?m
Î
STANDBY
STANDBY/ON
POWER
OFF ON
REFERENCE STEREO POWER AMPLIFIER
1
4
NOTE: The protection function will operate in case of internal amplifier malfunction or in case of external causes such as static electricity or speaker terminal short circuits. When the protection function operates, the POWER indicator flashes, and the unit goes out into standby mode. If this occurs, check the speaker terminals and speaker cords to make sure they are not shorted, then press the STANDBY/ON button to turn on the unit. If the protection function then operates again, unplug the power cord and contact a service center.
1 Main power ( -- OFF/ _ ON ) button
If the button is OFF (--), the power of the amplifier is shut off and the STANDBY/ON button on the amplifier does not function. Pressing the main power button will turn the amplifier ON (_).
2
STANDBY/ON button
Press to switch the amplifier ON or into STANDBY mode.
3 STANDBY indicator
Lights when the amplifier is in STANDBY mode. (Please note that this amplifier consumes a small amount of power (1 W) during the standby mode.)
4 POWER indicator
Lights when the power is switched on.
21
M-10X
SPECIFICATIONS
For KU/CA Type Amplifier Section
Continuous average power output of 100 watts* per channel, min., at 4 ohms, from 20 Hz to 20,000 Hz with no more than 0.2 %** total harmonic distortion. Puissance de sortie moyenne continue de 100 watts* par canal, minimum, sous 4 ohms, de 20 Hz à 20.000 Hz avec distorsion harmonique totale inférieure à 0,2 %**.
Continuous power output (both channels driven at 20 Hz to 20 kHz)** T.H.D. 0.2 %, 4 .......................... 100 W + 100 W T.H.D. 0.2 %, 8 .............................. 70 W + 70 W Total harmonic distortion** 20 Hz to 20 kHz, 8 .................................... 0.05 % Input sensitivity/ impedance ........... 700 mV/ 47 k +0 Frequency response ............ 5 Hz to 100 kHz 3 dB Signal-to-Noise ratio (IHF A network, short circuit) .............................................................. 118 dB Power Supply/ Miscellaneous Power requirements ................ AC 120 Volts, 60 Hz Power consumption ....................................... 198 W Power consumption in standby mode ............. 1 W Consommation (en veille) ................................. 1 W Dimensions ........... 420 (W) × 319 (D) × 128 (H) mm (including knobs and other protruding parts) Weight (without package) .............................. 7.6 kg Accessories Operating instructions ............................................ 1 Power cord (Rated current 7 A) ............................. 1 Remote control cord ............................................... 1 Warranty card .......................................................... 1
For MY Type Amplifier Section
Continuous power output (both channels driven at 20 Hz to 20 kHz)* T.H.D. 0.09 %, 4 ............................................... 90 W + 90 W T.H.D. 0.05 %, 8 ............................................... 60 W + 60 W DIN Continuous power output (both channels driven at 1 kHz) T.H.D. 1.0 %, 4 ............................................. 120 W + 120 W T.H.D. 1.0 %, 8 ................................................. 75 W + 75 W Total harmonic distortion* 20 Hz to 20 kHz, 8 ...................................................... 0.05 %
·Power output specification is for when power supply is 230V.
Input sensitivity/ impedance ................................. 700 mV/ 47 k Frequency response ................................... 5 Hz to 100 kHz +0 dB 3 Signal-to-Noise ratio (IHF A network, short circuit) ........................................................................................ 118 dB
Power Supply/ Miscellaneous
Power requirements ...................... AC 220 230 Volts, 50/ 60 Hz Power consumption ............................................................. 220 W Power Consumption in standby mode ................................... 1 W Dimensions ................................ 420 (W) × 319 (D) × 128 (H) mm (including knobs and other protruding parts) Weight (without package) ................................................... 7.6 kg
Accessories
Operating instructions ................................................................. 1 Power cord (Rated current 2.5 A) ................................................ 1 Remote control cord .................................................................... 1 Warranty card ............................................................................... 1
NOTE: Specifications and design subject to possible modification without notice, due to improvements.
* Measured by Audio Spectrum Analyzer.
NOTE: Specifications and design subject to possible modification without notice, due to improvements. * M e a s u r e d p u r s u a n t t o t h e F e d e r a l Tr a d e Commission's Trade Regulation rule on Power Output Claims for Amplifiers. ** Measured by Audio Spectrum Analyzer.
22