Text preview for : Studer-970 mix.pdf part of Studer 970 mixer
Back to : Studer-970 mix.part01.rar | Home
Professional Audio System Components
CONTENTS
1 2 Introduction.................................................................................................................................................................................3 MSC System................................................................................................................................................................................4 2.1 Modular Sub-Cards (MSCs).............................................................................. .................................................................5 2.1.1 Motherboard for 1 MS-Card ....................................................................1.914.500................................................5 2.1.2 Breadboarding Card ..................................................................................1.914.529................................................5 2.1.3 Line Output Amplifier ..............................................................................1.914.501................................................6 2.1.4 High-Level Input Amplifier .....................................................................1.914.502/504 ........................................8 2.1.5 Loudspeaker Amplifier .............................................................................1.914.505..............................................10 2.1.6 Microphone Pre-Amplifiers .....................................................................1.914.506/507 ......................................11 2.1.7 VCA with Electronically Balanced Connections ....................................1.914.515..............................................13 2.1.8 VCA with 1 or 3 Control Ports ...............................................................1.914.518/528 ......................................15 2.1.9 Limiter Voltage Processor .......................................................................1.914.519..............................................17 2.1.10 1900 Hz Signal Generator .......................................................................1.914.520..............................................19 2.1.11 Call Decoder 20...60 Hz ..........................................................................1.914.521..............................................20 2.1.12 Call Decoder 1900 Hz .............................................................................1.914.522..............................................21 2.1.13 Relay Sub-Cards .......................................................................................1.914.523/524/525/526 ......................22 2.1.14 0- Input Amplifier with PFL Facility ...................................................1.914.530..............................................23 2.1.15 High Level Input with PFL Facility .........................................................1.914.531..............................................24 2.1.16 Flip-flop Unit ............................................................................................1.914.532..............................................25 2.1.17 90° Filter ...................................................................................................1.914.533..............................................26 2.1.18 Dual Vox Detector ...................................................................................1.914.534..............................................28 2.1.19 Microphone Amplifier with Limiter ........................................................1.914.539..............................................29 2.1.20 Dual Fader/VCA Control Voltage Interface ...........................................1.914.540 /541 .....................................31 2.2 Euro-Cards......................................................................................................... ...............................................................32 2.2.1 Motherboard for 4 MS-Cards ..................................................................1.915.770..............................................32 2.2.2 Power Supply ............................................................................................1.915.100..............................................33 2.2.3 Audio Generator .......................................................................................1.915.200..............................................35 2.2.4 Monitor Amplifier and Switching Relays (Studio/CR) .........................1.915.304..............................................37 2.2.5 Distribution Amplifier .............................................................................1.915.307/308 ......................................39 2.2.6 5 W Power Amplifier ...............................................................................1.915.410/415 ......................................41 2.2.7 40 W Power Amplifier .............................................................................1.915.440/441 ......................................43 2.2.8 Monitor Switching Relays ........................................................................1.915.601/602 ......................................45 2.2.9 Transistor-Driven Relays (7+2) ...............................................................1.915.603..............................................47 2.2.10 Dual Limiter .............................................................................................1.915.700..............................................49 2.2.11 Telephone Hybrid .....................................................................................1.915.760/764 ......................................51 2.2.12 Line Equalizer ...........................................................................................1.915.776/777/779 ..............................53 2.2.13 Dual Balancing Unit/Dual Line Amplifier ..............................................1.915.904..............................................56 2.3 Racks and Frames .............................................................................................. ...............................................................59 2.3.1 19" Mounting Frame for 3 Euro-Cards ..................................................1.918.100..............................................59 2.3.2 19" Ventilation Unit/19" Blank Panels .................................................1.918.119/0XX.....................................61 2.3.3 19" Euro-Card Mounting Frames ...........................................................1.918.318/319 ......................................62 2.3.4 19" Euro-Card Mounting Accessories .................................................... ...............................................................63
Date printed: 29.11.01
E1
Professional Audio System Components
1
INTRODUCTION
The individual descriptions and application notes contained in this brochure are intended to acquaint designers and project engineers with the Studer Audio System Components. They allow to realize custom-tailored signal distribution, signal switching and amplifying systems to satisfy almost any individual requirement. Euro-Cards (1.915....) The backbone of the system is the so-called Euro-card, a circuit board measuring 100 × 160 mm, which comes in a great variety of different circuit configurations. Furthermore, there are the Modular Sub-Cards, small plug-in cards. Four of them can be accommodated on one Euro-size motherboard, allowing to make up a system which provides the ultimate in flexibility. Matching 19" mounting frames and 19" sub-racks for Euro-cards with or without power supply are available as well as installation hardware. For prices please consult your local Studer distributor or contact: Studer Professional Audio GmbH Althardstrasse 30 CH-8105 Regensdorf Switzerland Phone: +41 44 870 75 11 Fax: +41 44 870 71 34 e-mail: [email protected] We reserve the right to change the design and the performance specifications of the products listed here as technical progress may warrant.
Modular Sub-Cards (1.914....)
Racks, Frames (1.918....)
Date printed: 29.11.01
E3
Professional Audio System Components
2
MSC SYSTEM
To provide highest possible flexibility for the designer of professional sound systems, Studer engineers have pursued a completely new concept. The Euro-card is a convenient circuit board as far as its size and its plug-in features are concerned. However, it often offers excess space for a particular circuit. This has triggered the idea to utilize the Euro-card simply as a carrier ("motherboard", order no. 1.915.770) for four smaller plug-in circuit boards, the "Modular Sub-Cards" (MSC). The 32 connections of the Euro-card are divided into 6 supply lines common to the modular sub-cards, and 4 × 6 individual lines joining the plugin sockets for each sub-card. The remaining 2 connections are used as separate bus lines, one of them leading to sub-cards 1 and 2, the other one to sub-cards 3 and 4, resulting in a total of 13 connections to each MSC. A small motherboard for only one MSC is available as well (order no. 1.914.500).
· · · · · · · · · · · · ·
A great variety of different circuits is available in form of MSCs, such as Balancing amplifiers Microphone pre-amplifiers Speaker amplifiers 0- input amplifiers Limiters Voltage controlled amplifiers (VCAs) Relay sub-cards High level input amplifiers Line output amplifiers 1900 Hz signal generator/decoder 90° filter, stereo/mono Flip-flop Breadboarding card (0.1"/2.54 mm grid) To meet the requirements of a system concept, a designer will be able to build individual circuits similar to working with a construction set: He either selects from the available circuits on Euro-cards or makes up his own Euro-card by simply arranging the most suitable combination of Modular Sub-Cards on the motherboard.
E4
Date printed: 29.11.01
Professional Audio System Components
2.1
2.1.1
Modular Sub-Cards (MSCs)
Motherboard for 1 MS-Card
1.914.500
Note:
If only one MS-card is used, this motherboard is helpful for both mechanical and electrical interfacing. It consists of an aluminium mounting base (135 × 36 mm) and a small PCB with a connector for the MS-card; for wiring, this PCB contains solder terminals. For installation of up to four MS-cards, there is a second, Euro-card format motherboard available (1.915.770) that can be installed into an Eurocard rack. Please refer to chapter 2.2.1.
Ordering Information
Motherboard for 1 MS-card
1.914.500.xx
2.1.2
Breadboarding Card
1.914.529
This experimental board is an empty plug-in PCB compatible with the MSC system. It offers a punched 0.1" grid (2.54 × 2.54 mm) for individual component placement.
Ordering Information:
Breadboarding card
1.914.529.xx
Date printed: 29.11.01
E5
Professional Audio System Components
2.1.3
Line Output Amplifier
1.914.501
Designed for operation at a nominal line level of +6 dBu (1.55 Vrms), this amplifier can handle levels of up to +24 dBu (12.3 Vrms), providing an excellent overload margin without the risk of clipping. A unique circuit around the primary of the amplifier's output transformer ensures excellent frequency response performance throughout the audible range. Fine and coarse gain adjustment is provided which allows to accommodate input levels in the range from 22...+8 dBu for a nominal +6 dBu output.
E6
Date printed: 29.11.01
Professional Audio System Components
Technical Specifications Input: Impedance Overload point Impedance Minimum load Maximum level Gain Frequency response THD Equivalent input noise > 10 k, electronically balanced (transformerless) +24 dBu < 50 , balanced and floating 200 +24 dBu 2 dB...+28 dB; adjustment: coarse 0 or 15 dB/fine 2 dB...+13 dB ±0.2 dB, 30 Hz...16 kHz < 0.01%, 30 Hz...16 kHz < 106 dB, linear, at 6 dB gain ±15 V (25 mA idling; max. 170 mA at +24 dBu into 200 ) MS-card, 34 × 85 mm Line output amplifier 1.914.501.xx
Output:
Supply: Dimensions: Ordering Information:
Date printed: 29.11.01
E7
Professional Audio System Components
2.1.4
High-Level Input Amplifier
1.914.502/504
Basically, this is an amplifier with near 0 dB gain for high-level applications, yet with additional features, such as remote muting facility, RF input filter, and choice of two input and output impedances. The input configuration is balanced, whereas the output is unbalanced. Jumpers in the primary of the input circuit permit selection of either high-impedance operation with RF filter or a 0- input without filter, for summing-bus applications. The combining (mixing) resistors have to be added externally. By switching pin3 of the amplifier's 13-pin plug to ground (via a corresponding connection on the motherboard) the amplifier may be muted from a remote point. If only 20 dB level reduction is desirable instead of muting, this can be programmed by connecting a resistor across two solder points.
E8
Date printed: 29.11.01
Professional Audio System Components
The amplifier may be used, for example, to work into a 600 load, or into the input of a 0- input amplifier of another summing circuit. If transformerless yet balanced input configuration is desired, an MSC amplifier with basically the same performance characteristics is available as well. Refer to the ordering information below. Technical Specifications Input: Impedance Common mode rejection Overload point Output: Impedance Minimum load Maximum level Impedance Maximum gain Maximum attenuation Frequency response THD Equivalent input noise Programmable attenuation > 10 k (transformer- or electronically balanced versions available; input with RF filter; 0- input selectable with jumpers) > 50 dB +24 dBu (12.3 Vrms) 33 (pin1), unbalanced 600 +20 dBu (7.75 Vrms) 3.3 k (pin2), unbalanced, for 0- operation 1 dB 30 dB ±0.3 dB, 30 Hz...16 kHz < 0.03%, 30 Hz...16 kHz 100 dBu, unweighted, at 6 dB attenuation 20 dB (resistor 33 k across muting circuit) ±15 V (11 mA idling) MS-card, 34 × 85 mm High level input amp with transformer-balanced input High level input amp with electronically balanced input 1.914.502.xx 1.914.504.xx
Supply: Dimensions: Ordering Information:
Date printed: 29.11.01
E9
Studer Audio Components
HL Input Amp, transformer-balanced 1.914.502.81 ( 1)
Idx. Pos. 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 1 C1 C2 C3 C5 C6 C 11 C 12 C 13 C 14 C 15 C 16 C 17 C 18 C 19 D1 D2 D3 IC 1 IC 2 J1 J2 J3 P1 P2 Q1 Q2 R1 R2 R3 R4 R5 R6 R7 R8 R 11 R 12 R 13 R 14 R 15 R 16 R 17 R 18 R 19 R 20 R 21 R 22 R 23 R 24 R 25 R 26 R 27 R 28 T1 W1 W2 Part No. Qty. Type/Val. Description Idx. Pos. Part No. Qty. Type/Val. Description 59.05.1681 59.05.1681 59.06.5682 59.34.5391 59.34.2220 59.26.0470 59.32.4102 not used 59.26.0470 59.06.0102 59.26.0470 59.26.2689 59.26.2689 59.06.0102 50.04.0125 50.04.0125 50.04.0125 50.05.0244 50.09.0106 54.01.0021 54.01.0021 54.01.0021 54.01.0273 54.01.0020 11 pcs 50.03.0350 50.03.0350 57.11.3152 57.11.3392 57.11.3152 57.11.3392 57.11.3392 57.11.3472 57.11.3432 57.11.3101 57.11.3104 57.11.3332 57.11.3223 not used 57.11.3104 57.11.5106 57.11.5335 57.11.5335 57.11.3151 57.11.3821 58.01.9202 57.11.3561 57.11.3104 57.11.3330 57.11.3332 57.99.0206 57.99.0206 57.11.3104 1.022.451.00 57.11.3000 64.01.0106 680p PP, 1%, 630V 680p PP, 1%, 630V 6n8 PETP, 63V, 5%, RM5 390p CER 63V, 5%, N1500 22p CER 63V, 5%, N150 47u SAL 6.3V 20% 1n0 CER 20%, 50V 1n0 PETP, 63V, 10%, RM5 47u SAL 6.3V 20% 1n0 PETP, 63V, 10%, RM5 47u SAL 6.3V 20% 6u8 SAL 16V 20% 6u8 SAL 16V 20% 1n0 PETP, 63V, 10%, RM5 1N4448 75V, 150mA, 4ns, DO-35 1N4448 75V, 150mA, 4ns, DO-35 1N4448 75V, 150mA, 4ns, DO-35 5534A Single Op-amp, low noise 5532A Dual Op-Amp, low noise Jumper 0.63*0.63mm, Au Jumper 0.63*0.63mm, Au Jumper 0.63*0.63mm, Au 13p Stecker CIS parallelsteck 1p Pin, 1reihig, gerade J112 JFET N-Channel J112 JFET N-Channel 1k5 MF, 1%, 0207 3k9 MF, 1%, 0207 1k5 MF, 1%, 0207 3k9 MF, 1%, 0207 3k9 MF, 1%, 0207 4k7 MF, 1%, 0207 4k3 MF, 1%, 0207 100R MF, 1%, 0207 100k MF, 1%, 0207 3k3 MF, 1%, 0207 22k MF, 1%, 0207 33k MF, 1%, 0207 optional (20 dB attenuation) 100k MF, 1%, 0207 10M MF, 5%, 0207 3M3 MF, 5%, 0207 3M3 MF, 5%, 0207 150R MF, 1%, 0207 820R MF, 1%, 0207 2k0 Cermet, 10%, 0.5W, vertical 560R MF, 1%, 0207 100k MF, 1%, 0207 33R MF, 1%, 0207 3k3 MF, 1%, 0207 50R PTC, 25V, 0.5W 50R PTC, 25V, 0.5W 100k MF, 1%, 0207 1:0.62 EINGANGSTRAFO 1 : 0,62 0R0 MF, 0207 0.6mm Schaltdraht Cu
Page: 1 of 1
End of List Comments: (01) W1, W2 added
Date printed: 06.11.2006
Studer Audio Components
HL Input Amp, electronically balanced 1.914.504.81 ( 1)
Idx. Pos. 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 1 1 C1 C2 C3 C4 C5 C6 C7 C 11 C 12 C 14 C 15 C 16 C 17 C 18 C 19 D1 D2 D3 IC 1 IC 2 J1 J2 J3 P1 P2 Q1 Q2 R1 R2 R3 R4 R5 R6 R7 R8 R 11 R 12 R 13 R 14 R 15 R 16 R 17 R 18 R 19 R 20 R 21 R 22 R 23 R 24 R 25 R 26 R 27 R 28 W1 W2 Part No. Qty. Type/Val. Description Idx. Pos. Part No. Qty. Type/Val. Description 59.05.1681 59.05.1681 59.26.0470 59.26.0470 59.34.2101 59.34.2220 59.34.2101 59.26.0470 59.32.4102 59.26.0470 59.06.0102 59.26.0470 59.26.2689 59.26.2689 59.06.0102 50.04.0125 50.04.0125 50.04.0125 50.05.0244 50.09.0106 54.01.0021 54.01.0021 54.01.0021 54.01.0273 54.01.0020 9 pcs 50.03.0350 50.03.0350 57.11.3152 57.11.3392 57.11.3152 57.11.3392 57.11.3104 57.11.3104 57.11.3332 57.11.3332 57.11.3104 57.11.3332 57.11.3223 not used 57.11.3104 57.11.5106 57.11.5335 57.11.5335 57.11.3151 57.11.3821 58.01.9202 57.11.3471 57.11.3104 57.11.3330 57.11.3332 57.99.0206 57.99.0206 57.11.3104 57.11.3000 64.01.0106 680p PP, 1%, 630V 680p PP, 1%, 630V 47u SAL 6.3V 20% 47u SAL 6.3V 20% 100p CER 63V, 5%, N150 22p CER 63V, 5%, N150 100p CER 63V, 5%, N150 47u SAL 6.3V 20% 1n0 CER 20%, 50V 47u SAL 6.3V 20% 1n0 PETP, 63V, 10%, RM5 47u SAL 6.3V 20% 6u8 SAL 16V 20% 6u8 SAL 16V 20% 1n0 PETP, 63V, 10%, RM5 1N4448 75V, 150mA, 4ns, DO-35 1N4448 75V, 150mA, 4ns, DO-35 1N4448 75V, 150mA, 4ns, DO-35 5534A Single Op-amp, low noise 5532A Dual Op-Amp, low noise Jumper 0.63*0.63mm, Au Jumper 0.63*0.63mm, Au Jumper 0.63*0.63mm, Au 13p Stecker CIS parallelsteck 1p Pin, 1reihig, gerade J112 JFET N-Channel J112 JFET N-Channel 1k5 MF, 1%, 0207 3k9 MF, 1%, 0207 1k5 MF, 1%, 0207 3k9 MF, 1%, 0207 100k MF, 1%, 0207 100k MF, 1%, 0207 3k3 MF, 1%, 0207 3k3 MF, 1%, 0207 100k MF, 1%, 0207 3k3 MF, 1%, 0207 22k MF, 1%, 0207 33k MF, 1%, 0207 optional (20 dB attenuation) 100k MF, 1%, 0207 10M MF, 5%, 0207 3M3 MF, 5%, 0207 3M3 MF, 5%, 0207 150R MF, 1%, 0207 820R MF, 1%, 0207 2k0 Cermet, 10%, 0.5W, vertical 470R MF, 1%, 0207 100k MF, 1%, 0207 33R MF, 1%, 0207 3k3 MF, 1%, 0207 50R PTC, 25V, 0.5W 50R PTC, 25V, 0.5W 100k MF, 1%, 0207 0R0 MF, 0207 0.6mm Schaltdraht Cu
Page: 1 of 1
End of List Comments: (01) R28, W1, W2 added
Date printed: 06.11.2006
Professional Audio System Components
2.1.5
Loudspeaker Amplifier
1.914.505
This low-power amplifier on a modular sub-card is designed to drive a 10...15 speaker. Power output is about 2...3 W. As can be concluded from this specification, the amplifier is not intended for high-quality monitoring. It will be ideally suited, however, for pre-fader listening and similar applications. The amplifier's input is balanced and floating, with adjustable gain.
Technical Specifications Input impedance Nominal power output Power output Distortion S/N Frequency response High pass filter Supply: Dimensions: Ordering Information: > 10 k, balanced and floating (with transformer) 2 W into 15 25 mW...2.5 W into 15 , with 0 dBu input < 0.5% at 2 W < 0.15% at 500 mW 99 dB, ref. to 2 W at max. gain 0.5 dB at 15 kHz 150 Hz, 12 dB/oct. 24 V (40 mA idling, max. 220 mA fully driven) MS-card, 34 × 85 mm Loudspeaker amplifier 1.914.505.xx
E10
Date printed: 29.11.01
Professional Audio System Components
2.1.6
Microphone Pre-Amplifiers
1.914.506/507
Two different microphone pre-amplifiers are available, for dynamic or condenser microphones, and for electret microphones. Both offer high gain and low noise, as is required for microphone pre-amplification. 1.914.506 features a balanced and floating input. It is designed for dynamic or condenser microphones with a source impedance of 200 or less. An RF filter is incorporated at the input transformer's primary. Furthermore, the input is equipped with the resistors required for phantom powering of condenser microphones. 1.914.507 is designed for unbalanced electret microphones requiring a 12 V supply. A wide range of input levels can be accommodated (see level diagram).
By using the same solid-state switching circuit as can be found in the line and high-level amplifiers, remote muting or activation of a fixed amount of attenuation are possible as well. The amplifier's two outputs are unbalanced, with impedances of 3.3 k or 33 , respectively.
Date printed: 29.11.01
E11
Professional Audio System Components
Technical Specifications Input: Impedance Max. input level Common mode rejection Output: Max. level Nominal level Impedance Minimum load Max. gain Frequency response THD Noise figure, linear Supply: Transformer-balanced and floating, with RF filter (1.914.506) Unbalanced, with RF filter and electret supply (1.914.507) > 1 k, for microphones with an impedance of 200 or less. 2 dBu (615 mVrms); THD at 30 Hz: approx. 1% > 60 dB, unbalanced, to ground +20 dBu (7.75 Vrms) 0 dBu (0.775 Vrms) 33 (pin1) 3.3 k (pin2; to a 0- amp.) 600 71 dB (see level diagram) ±0.5 dB, 30 Hz...16 kHz < 0.3%, 30 Hz...16 kHz at 20 dB gain < 4.5 dB, input terminated with 200 ±15 V (11 mA idling) +48 V (1.914.506, only if phantom powering required) MS-card, 34 × 85 mm · · Microphone pre-amplifier for dynamic microphones Microphone pre-amplifier for electret microphones 1.914.506.xx 1.914.507.xx
Dimensions: Ordering Information:
E12
Date printed: 29.11.01
Professional Audio System Components
2.1.7
VCA with Electronically Balanced Connections
1.914.515
In contrast to the VCA 1.914.518/528 (chapter 2.1.8), this assembly features an electronically balanced input and output.
It is intended for use in balanced audio systems for a variety of applications, especially when gain is to be controlled from a remote point. It will be useful in audio-video post-production work where suitable DC ramps can control cross-fades, voice-overs, etc. Its high overload margin and its exceptionally low noise and distortion performance make it the perfect choice for high-quality audio applications. By connecting the gain control terminals of a number of VCAs to a common potentiometer or fader, several audio channels may thus be controlled simultaneously.
Two control inputs provide VCA gain control from two different remote points
Date printed: 29.11.01
E13
Professional Audio System Components
Technical Specifications Input: Impedance Clipping point 10 k, electronically balanced +24 dBu Electronically balanced 2 k +24 dBu 0.5 dB, 30 Hz...15 kHz +40...100 dB, with ext. control 0 V = unity gain; 1 dB/µA; jumper 1-2 20 dB/V; jumper 2-3 10 dB/V; jumper 3-4 10 dB/V < 0.1% 93 dBu @ unity gain ±15 V (25 mA) MS-card, 34 × 85 mm VCA with electronically balanced input and output 1.914.515.xx
Output: Recommended load Maximum level Frequency response Gain/attenuation range Control input: pin1; gain tracking
Control input: pin10; gain tracking THD Equivalent input noise Supply: Dimensions: Ordering Information:
E14
Date printed: 29.11.01
Professional Audio System Components
2.1.8
VCA with 1 or 3 Control Ports
1.914.518/528
Within the range of modular sub-cards, two more VCAs are available. Voltage controlled amplifiers are ideally suited for applications such as remote level control, level limiting (in combination with the voltage processor 1.914.519) or for automatic "voice-over" circuits, when driven by suitable ramp generators. These VCAs offer outstandingly low noise and harmonic distortion.
For best performance, they should be operated at a level of 0 dBu. Gain pre-selection is possible on the 1.914.518 version, allowing gain/attenuation ranges either from +10 to 90 dB or from +40 to 70 dB, using an external potentiometer. The 1.914.528 VCA card differs in that it is equipped with three external control inputs, providing gain control from three different locations.
Date printed: 29.11.01
E15
Professional Audio System Components
Technical Specifications Input: Impedance Clipping point Impedance Max. level Recommended load Frequency response External gain control Gain/attenuation range (pot. meter) Gain tracking THD Equivalent input noise Supply: Dimensions: Ordering Information: > 3 k +20 dBu 33 or 3.3 k, selectable +20 dBu 2 k 0.5 dB, 30 Hz...16 kHz +40...90 dB (1.914.518.xx) +40...100 dB (1.914.528.xx) +40...60 dB / +10...70 dB / +10...90 dB (1.914.518.xx only, jumperselectable) 10 dB/V < 0.1% 102 dBu ±15 V (40 mA) MS-card, 34 × 85 mm Voltage controlled amplifier with 1 control port Voltage controlled amplifier with 3 control ports 1.914.518.xx 1.914.528.xx
Output:
E16
Date printed: 29.11.01
Professional Audio System Components
2.1.9
Limiter Voltage Processor
1.914.519
Together with this voltage processor, the VCAs 1.914.518/528 can perform as signal level limiters.
The processor's threshold can be set within a wide range of levels, so that limiting action becomes effective at a desired level within a range of 15 to +15 dBu. Limiting action attacks within 1 ms, whereas release can vary from 50 ms to 5 s, depending on the program's energy content. This means that no audible "pumping" action which is often associated with such a device will occur. After the cessation of loud passages, amplification will recover only slowly. For stereo applications, a two-channel setup (VCAs and voltage processor) can be linked, so that identical amounts of gain reduction will take place simultaneously in both channels.
The input of the voltage processor has to be wired to the output of the VCA. The processor's output, when connected to the VCA's control terminal, will effect the necessary gain reduction so that a limiting characteristic is obtained. The limiting threshold is adjustable in a wide range. Remote on/off switching of the limiter function is possible.
Date printed: 29.11.01
E17
Professional Audio System Components
Technical Specifications Limiter: Input impedance Max. input level Frequency range Output voltage Threshold level Attack time Release time Compression ratio 10 k +20 dBu 30 Hz...16 kHz 0...13 VDC 15 dBu...+15 dBu 1 ms 50 ms...5 s, program-depending 20:1, in conjunction with a VCA ±15 V (10 mA) MS-card, 34 × 85 mm Limiter voltage processor 1.914.519.xx
Supply: Dimensions: Ordering Information:
E18
Date printed: 29.11.01
Professional Audio System Components
2.1.10
1900 Hz Signal Generator
1.914.520
This signal generator produces a stable frequency of 1900 Hz to establish communication on outside broadcast lines, as specified in the EBU/CCIR recommendations.
Technical Specifications Frequency Distortion Output level Output Output Impedance, out 1 out 2 Minimum load Supply: Dimensions: Ordering Information: 1900 Hz (adjustable) < 1% 15...+6 dBu (adjustable) balanced and floating < 15 600 200 ±15 V (20 mA) MS-card, 34 × 85 mm 1900 Hz signal generator 1.914.520.xx
Date printed: 29.11.01
E19
Professional Audio System Components
2.1.11
Call Decoder 20...60 Hz
1.914.521
This assembly features a call receiver for the ringing frequency on telephone lines (20...60 Hz). The receiver can activate an optical and/or an acoustical signal generated by an external buzzer (not supplied). In normal mode the buzzer will be on until reset. In linked mode the signal lasts only as long as a call is detected.
Technical Specifications Input: Impedance Frequency Min. level Nominal level Supply: Dimensions: Ordering Information: balanced, floating; no DC > 20 k 20...60 Hz 17 Vrms 70 Vrms +15 V (5 mA); 15 V (10 mA); 6 V (2 mA) MS-card, 34 × 85 mm Call decoder 20...60 Hz 1.914.521.xx
E20
Date printed: 29.11.01
Professional Audio System Components
2.1.12
Call Decoder 1900 Hz
1.914.522
This card contains a call receiver for the standardized 1900 Hz call frequency on OB lines. It is tuned to respond to 1900 Hz ±1 %. The receiver can be switched either to activate an optical or an acoustical signal for the duration of the 1900 Hz call (linked mode), or the acoustical signal can be selected to remain activated until reset (normal mode). The acoustical signal can be generated by an external buzzer (not supplied).
Technical Specifications Input: Frequency Impedance Min. level Nominal level Supply: Insulation rating Dimensions: Ordering Information: balanced, floating; no DC 1900 Hz, ±1% > 10 k 30 dBu +24 dBu +15 V (5 mA); 15 V (10 mA); 6 V (2 mA) 500 VDC MS-card, 34 × 85 mm Call decoder 1900 Hz 1.914.522.xx
Date printed: 29.11.01
E21
Studer Audio Components
Call Decoder 1900 Hz 1.914.522.00 ( 1)
Idx. Pos. 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 0 0 1 0 0 0 0 0 0 0 0 C2 C3 C4 C5 C6 C7 C8 C9 C 10 C 11 C 12 C 13 C 14 D3 D4 D5 D6 D7 IC 1 IC 2 IC 3 P1 Q1 Q2 R1 R2 R3 R4 R5 R7 R8 R9 R 10 R 11 R 12 R 13 R 14 R 15 R 16 R 17 R 18 R 19 R 20 R 21 R 22 R 23 R 24 R 25 R 26 T1 Part No. 59.06.0102 59.06.0102 59.06.0222 59.05.2472 59.34.4121 59.06.0103 59.26.5229 59.06.0224 59.06.5474 59.26.2689 59.26.2689 59.26.2689 59.26.2689 50.04.0125 50.04.0125 50.04.0125 50.04.0125 50.04.1117 50.09.0101 50.07.0032 50.07.1011 54.01.0273 50.03.0515 50.03.0436 57.11.3562 57.11.3562 57.11.3123 57.11.3104 57.11.3392 57.11.5155 58.01.8203 57.11.3154 57.11.3104 57.11.3104 57.11.3103 57.11.3103 57.11.5225 57.11.3104 57.11.5225 57.11.3105 57.11.3104 57.11.5225 57.11.3105 57.11.3104 57.11.3220 57.99.0206 57.99.0206 57.99.0206 57.11.3391 1.022.218.00 Qty. Type/Val. 1n0 1n0 2n2 4n7 120p 10n 2u2 220n 470n 6u8 6u8 6u8 6u8 1N4448 1N4448 1N4448 1N4448 12V TL072 FX101 4011 13p BC307B BC237B 5k6 5k6 12k 100k 3k9 1M5 20k 150k 100k 100k 10k 10k 2M2 100k 2M2 1M0 100k 2M2 1M0 100k 22R 50R 50R 50R 390R 1:1 Description PETP, 63V, 10%, RM5 PETP, 63V, 10%, RM5 PETP, 63V, 10%, RM5 PP, 2.5%, 63V CER 63V, 5%, N750 PETP, 63V, 10%, RM5 SAL, 20%, 25V PETP, 63V, 10%, RM5 PETP, 63V, 5%, RM5 SAL 16V 20% SAL 16V 20% SAL 16V 20% SAL 16V 20% 75V, 150mA, 4ns, DO-35 75V, 150mA, 4ns, DO-35 75V, 150mA, 4ns, DO-35 75V, 150mA, 4ns, DO-35 Zener, 5%, 0.5W, DO-35 Dual op-amp biFET IC FX-101 L, ,A Quad 2-inp NAND Stecker CIS parallelsteck PNP 100mA 45V NPN 100mA 45V MF, 1%, 0207 MF, 1%, 0207 MF, 1%, 0207 MF, 1%, 0207 MF, 1%, 0207 MF, 5%, 0207 Cermet, 10%, 0.5W, horizontal MF, 1%, 0207 MF, 1%, 0207 MF, 1%, 0207 MF, 1%, 0207 MF, 1%, 0207 MF, 5%, 0207 MF, 1%, 0207 MF, 5%, 0207 MF, 1%, 0207 MF, 1%, 0207 MF, 5%, 0207 MF, 1%, 0207 MF, 1%, 0207 MF, 1%, 0207 PTC, 25V, 0.5W PTC, 25V, 0.5W PTC, 25V, 0.5W MF, 1%, 0207 EINGANGSTRAFO 1 : 1 Idx. Pos. Part No. Qty. Type/Val. Description
Page: 1 of 1
End of List Comments: (01) IC3, R16, R19 changed
Date printed: 06.11.2006
Professional Audio System Components
2.1.13
Relay Sub-Cards
1.914.523/524/525/526 Audio signal routing or enabling/disabling of certain circuit sections is often effected best using relays. The Modular Sub-Card System, therefore, offers a selection of four relays on individual circuit boards. Because only one relay can be accommodated on one MS-Card, several cards (or a card from the Euro-card range) will be required if more complex switching has to be realized.
The relays offer double pole/double throw switching with non-shorting contacts, and coils rated for either 6 VDC or 24 VDC operation. A diode is wired across the relay coil in all versions to suppress interfering backEMF when de-energizing the relay. For studio applications where the mechanical click produced by the relay's armature is objectionable, a low-noise type is available.
No. Coil 1.914.523 6 VDC / 137 1.914.524 24 VDC / 2.0 k * 1.914.525 5 VDC / 135 * 1.914.526 24 VDC / 2.6 k * Low-noise relays Contact Rating 220 V / 2 A / 60 W 220 V / 2 A / 60 W 100 V / 0.5 A / 30 W (R1 = 27 for 6 V operation) 100 V / 0.5 A / 30 W (R1 = 0 )
Dimensions: Ordering Information:
MS-card, 34 × 85 mm MSC relay 6 VDC MSC relay 24 VDC MSC relay 6 VDC; low-noise MSC relay 24 VDC; low-noise 1.914.523.xx 1.914.524.xx 1.914.525.xx 1.914.526.xx
E22
Date printed: 29.11.01
Professional Audio System Components
2.1.14
0- Input Amplifier with PFL Facility
1.914.530
This amplifier with its characteristic input impedance of less than 1 finds its application as a summing amplifier. A multitude of unbalanced sources can thus be mixed with a high degree of effective isolation between the individual inputs.
When using 3.3 k resistors as combining (mixing) resistors in series with each source feeding the summing bus, gain will be unity (0 dB), i.e., the amplifier's output level will be equal to the level of the signal source ahead of the combining resistor. The amplifier's output is unbalanced, with low impedance. Additional outputs for monitoring (or pre-listening) can be activated via solid-state switches by remote control.
Technical Specifications Input: Max. current Current for 0 dBu Impedance Max. output swing Load Frequency response THD Noise voltage at the output Noise figure, 12 inputs 2.5 mArms for max. output swing 234.2 µA; 0 dBu output (= 3.3 k at the input for unity gain) 33 +20 dBu 600 @ max. output swing ±0.3 dBu, 30 Hz...16 kHz < 75 dB, 30 Hz...16 kHz 110 dBu, input terminated with 3.3 k, bandwidth 23 kHz F < 2 dB = RS = 275 +15 V (11 mA idling); 15 V (7 mA idling) MS-card, 34 × 85 mm Zero- input amplifier (PFL facility) 1.914.530.xx
E23
Output:
Supply: Dimensions: Ordering Information:
Date printed: 29.11.01
Professional Audio System Components
2.1.15
High-Level Input with PFL Facility
1.914.531
This compact high-level input amplifier features a balanced and floating input stage. The output is unbalanced, with low impedance and low distortion up to +24 dBu. An additional PFL monitoring facility is electronically switchable (FET).
Technical Specifications Input: Impedance Max. level CMRR Balanced and floating > 10 k +26 dBu > 110 dB @ 50 Hz > 110 dB @ 16 kHz Unbalanced 33 600 @ max. output swing +20 dBu 1.4...17.8 dB ±0.3 dB, 30 Hz...16 kHz < 85 dB, 30 Hz...16 kHz < 107 dBu, gain 6 dB, bandwidth 23 kHz ±15 V (10 mA idling) MS-card, 34 × 85 mm HL input with PFL 1.914.531.xx
Output: Impedance Load Max. output swing Gain Frequency response THD Noise voltage Supply: Dimensions: Ordering Information:
E24
Date printed: 29.11.01
Professional Audio System Components
2.1.16
Flip-flop Unit
1.914.532 The Flip-flop Unit consists of a relay with two DPDT contacts and a flipflop circuit with a control input (opto-coupler). A ground pulse from a non-latching switch applied to the input activates the relay. A next ground pulse will deactivate it again.
Technical Specifications Input: Relay contacts: Supply: Max. rating floating, with opto-coupler 100 V/0.5 A/30 W 6 V for logic 24 V for opto-coupler MS-card, 34 × 85 mm Flip-flop unit 1.914.532.xx
Dimensions: Ordering Information:
Date printed: 29.11.01
E25
Professional Audio System Components
2.1.17
90° Filter
1.914.533 This active 90° filter is used to form a monophonic signal from the left and right channel of stereo signals. Simple mixing of the left and right channel will not produce a mono signal of satisfactory quality, but results in an emphasis of the center information. By summing the stereo signals in a 90° phase-shifted manner, this undesirable effect can be avoided.
The 90° filter consists of two all-pass filter chains, producing a uniform 90° phase difference across the whole audio range. The left and the right stereo signals are each passed through one of these filters and added at the filter's output. Doubling of equally-phased signal components as well as canceling of opposite-phased components is thus avoided.
The filter circuits are of unbalanced configuration. For this reason a summing circuit usually consists of two high-level amplifiers with balanced inputs (1.914.502), one 90° filter, and one high-level output amplifier (1.914.501), all accommodated on one MSC motherboard, as shown in the diagram above. The gain of this combination can be adjusted. A correlated stereo input of equal level in both channels will provide a mono signal of identical level. With only one input channel (left or right), the mono output level will be lower by 3 dB. Since the 90° filter with its input and output cards can be realized on a single, Euro-card size MSC motherboard, it can possibly be combined with other Audio Components, such as limiters and isolation amplifiers. Such stereo-to-mono combinations are in use at various radio stations to feed the stereo programs to the monophonic AM-transmitter in a correctly summed manner.
E26
Date printed: 29.11.01
Professional Audio System Components
Technical Specifications Input: Max. level Impedance Max. level Impedance Frequency response Phase THD Noise +20 dBu 4 k +20 dBu 6.8 k 30 Hz...16 kHz, ±0.3 dB 90° ±3°; 30 Hz...16 kHz 80 dB < 95 dBu ±15 V (18 mA idling) MS-card, 34 × 85 mm 90° filter stereo/mono 1.914.533.xx
Output:
Supply: Dimensions: Ordering Information:
Date printed: 29.11.01
E27
Professional Audio System Components
2.1.18
Dual Vox Detector
1.914.534
The Dual Vox Detector card contains two adjustable threshold level detector circuits. Threshold level (22 dBu...+16 dBu) and release time (0.2 s...10 s) are separately adjustable for two audio channels. These adjustments are effected very precisely with multi-turn trimmer potentiometers.
The high-impedance audio input is balanced. The open-collector output is prepared to activate a relay or an alarm device. A possible application of this card would be to detect incoming modulation.
Technical Specifications Inputs: Impedance Max. level Frequency response Threshold level Attack time Release time Hysteresis Outputs: Supply: Dimensions: Ordering Information: Electronically balanced 10 k +24 dBu (0 dBu = 0,775 Vrms) 75 Hz...12 kHz, 3 dB 22 dBu...+16 dBu 100 ms 200 ms...10 s 1 dB Open-collector; UCE +45 V; Imax 100 mA ±15 V ( 15 mA / 4 mA idling) MS-card, 34 × 85 mm Dual vox detector 1.914.534.xx
E28
Date printed: 29.11.01
Professional Audio System Components
2.1.19
Microphone Amplifier with Limiter
1.914.539
This assembly combines a microphone amplifier and a VCA limiter circuit with adjustable threshold level and program-depending release time. The input is balanced and floating, the output is unbalanced and with low impedance. Gain control is effected internally with a trimmer potentiometer, or externally with a gain-control DC voltage. A jumper-selectable pad reduces the input level by 21 dB.
The operation of the limiter circuit can be monitored at the gain reduction output, if an appropriate instrument (GRM) is connected. This card is ideally suited for talkback applications.
Date printed: 29.11.01
E29
Professional Audio System Components
Technical Specifications Input: Impedance Max. level Pad (attenuation) CMRR Source impedance Output: Max. level Impedance Load Gain adjust (v1) > 1 k, balanced, floating 2 dBu (THD at 30 Hz 1%) +19 dBu, pad on 21 dB, jumper-selectable > 60 dB @ 16 kHz 200 +20 dBu 33 2 k min. +10 dB, VCA = 0 dB; pad off max. +37 dB, VCA = 0 dB; pad off min. 11 dB, VCA = 0 dB; pad on max. +16 dB, VCA = 0 dB; pad on 10 dB/V 10...+6 V, pin3: gain control input vtot = v1 + v2 > 90 dB ±0.5 dB, 30 Hz...16 kHz 50 dB, 20 dB gain; 30 Hz...16 kHz 95 dBu, pad on; 0 dB gain F ~ 10 dB, bandwidth = 23 kHz; 60 dB gain; Rs = 200 ; pad off 7...+20 dBu 0.5 ms 50 ms...1 s, program-dependent 10:1 @ 1 kHz ±15 V (25 mA) Microphone amplifier with limiter 1.914.539.xx
Gain control characteristics (v2) DC range Total gain Max. attenuation General: Frequency response THD Noise voltage Noise figure Threshold level Attack time Release time Compression ratio
Limiter:
Supply: Ordering Information:
E30
Date printed: 29.11.01
Professional Audio System Components
2.1.20
Dual Fader/VCA Control Voltage Interface
1.914.540 /541
These interfaces are used to convert the voltage of a linear fader to the non-linear dB scale of a Studer VCA. One card processes two channels. It is available in two versions: 540.xx (0...+10 VDC control voltage), and 541.xx (+5...0 VDC control voltage). A regulated +10 VDC reference voltage is generated on-board. The DC from the fader's wiper is connected to the input. Offset and scale alignment is performed with on-board trimmer potentiometers for matching the VCA gain to the dB scale of the fader.
Technical Specifications Input: Impedance Level range Impedance Control range 1.914.540.xx > 1 M, unbalanced 0...+10 V 33 , unbalanced +1 V...10 V ±15 V (15 mA) MS-card, 34 × 85 mm Fader/VCA control interface Fader/VCA control interface 1.914.540.xx 1.914.541.xx
E31
1.914.541.xx 100 k, unbalanced +5...0 V 33 , unbalanced +1 V...10 V
Output:
Supply: Dimensions: Ordering Information:
Date printed: 29.11.01
Studer Audio Components
Dual Fader/VCA Control Voltage IF 1.914.541.00 ( 0)
Idx. Pos. 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 C1 C2 C3 C4 C5 C6 C7 C8 C9 IC 1 IC 2 IC 3 IC 4 MP 1 MP 2 MP 3 P1 Q1 Q2 Q3 Q4 Q5 Q6 Q7 Q8 Q9 Q 10 R1 R2 R3 R4 R5 R6 R7 R8 R9 R 10 R 11 R 12 R 13 R 14 R 15 R 16 R 17 R 18 R 19 R 20 R 21 R 22 R 23 R 24 R 25 R 26 R 27 R 28 R 29 R 30 R 31 R 32 R 33 R 34 R 35 R 36 RA 1 RA 2 RA 3 RA 4 Part No. 59.60.3325 59.60.2249 59.60.2373 59.60.3337 59.60.3337 59.60.2249 59.68.0065 59.60.2373 59.60.3325 50.61.0201 50.10.0106 50.61.0201 50.61.0201 1.914.541.11 1.914.541.04 43.01.0108 54.01.0273 50.60.0002 50.60.0002 50.60.1002 50.60.1002 50.60.1002 50.60.1002 50.60.0002 50.60.0002 50.60.1002 50.60.1002 57.60.1101 57.60.1223 57.60.1113 not used 57.60.1104 57.60.1204 57.60.1113 57.60.1333 57.60.1223 57.60.1223 57.60.1223 57.60.1393 57.60.1241 57.60.1393 57.60.1223 57.60.1330 57.92.1820 57.92.1820 57.60.1681 57.60.1223 57.60.1223 57.60.1223 57.60.1223 57.60.1393 57.60.1223 57.60.1223 57.60.1113 not used 57.60.1104 57.60.1204 57.60.1241 57.60.1393 57.60.1223 57.60.1330 57.60.1684 57.60.1684 58.01.9103 58.01.9101 58.01.9103 58.01.9101 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 Qty. pce pce pce pce pce pce pce pce pce pce pce pce pce pce pce pce pce pce pce pce pce pce pce pce pce pce pce pce pce pce pce pce pce pce pce pce pce pce pce pce pce pce pce pce pce pce pce pce pce pce pce pce pce pce pce pce pce pce pce pce pce pce pce pce pce pce pce Type/Val. 10n 100p 1n0 100n 100n 100p 10u 1n0 10n TL062 TL431 TL062 TL062 Description CER 50V, 10%, X7R, 0805 CER 50V, 5%, C0G, 0603 CER 50V, 5%, C0G, 0805 CER 50V, 10%, X7R, 0805 CER 50V, 10%, X7R, 0805 CER 50V, 5%, C0G, 0603 EL 16V, 4.0*5.7 CER 50V, 5%, C0G, 0805 CER 50V, 10%, X7R, 0805 Dual FET Op-Amp Shunt regulator Dual FET Op-Amp Dual FET Op-Amp FADER/VCA INTERFACE2 PCB NR.-ETIKETTE 5 * 20 ESE-Warnschild Stecker CIS parallelsteck NPN 45V 100mA SOT 23 NPN 45V 100mA SOT 23 PNP 45V 100mA SOT 23 PNP 45V 100mA SOT 23 PNP 45V 100mA SOT 23 PNP 45V 100mA SOT 23 NPN 45V 100mA SOT 23 NPN 45V 100mA SOT 23 PNP 45V 100mA SOT 23 PNP 45V 100mA SOT 23 MF, 1%, 0204, E24 MF, 1%, 0204, E24 MF, 1%, 0204, E24 MF, 1%, 0204, E24 MF, 1%, 0204, E24 MF, 1%, 0204, E24 MF, 1%, 0204, E24 MF, 1%, 0204, E24 MF, 1%, 0204, E24 MF, 1%, 0204, E24 MF, 1%, 0204, E24 MF, 1%, 0204, E24 MF, 1%, 0204, E24 MF, 1%, 0204, E24 MF, 1%, 0204, E24 MF, 1%, 0204, E24 PTC 60V PTC 60V MF, 1%, 0204, E24 MF, 1%, 0204, E24 MF, 1%, 0204, E24 MF, 1%, 0204, E24 MF, 1%, 0204, E24 MF, 1%, 0204, E24 MF, 1%, 0204, E24 MF, 1%, 0204, E24 MF, 1%, 0204, E24 MF, 1%, 0204, E24 MF, 1%, 0204, E24 MF, 1%, 0204, E24 MF, 1%, 0204, E24 MF, 1%, 0204, E24 MF, 1%, 0204, E24 MF, 1%, 0204, E24 MF, 1%, 0204, E24 MF, 1%, 0204, E24 Cermet, 10%, 0.5W, vertical Cermet, 10%, 0.5W, vertical Cermet, 10%, 0.5W, vertical Cermet, 10%, 0.5W, vertical Idx. Pos. Part No. Qty. Type/Val. Description
Page: 1 of 1
Label 13p BC850C BC850C BC860C BC860C BC860C BC860C BC850C BC850C BC860C BC860C 100R 22k 11k 22k 100k 200k 11k 33k 22k 22k 22k 39k 240R 39k 22k 33R 94mA 94mA 680R 22k 22k 22k 22k 39k 22k 22k 11k 22k 100k 200k 240R 39k 22k 33R 680k 680k 10k 100R 10k 100R
End of List Comments:
Date printed: 06.11.2006
Professional Audio System Components
2.2
2.2.1
Euro-Cards
Motherboard for 4 MS-Cards
1.915.770
The Modular Sub-Cards require a mounting base for mechanical and electrical installation. This motherboard for four MS-cards in standard Euro-card size easily integrates into the Studer audio components system; it carries 32 printed tracks from its edge connector to four small plug-in sockets. Each socket has 13 contacts; six of them are common supply lines, while another six are individual to each socket. Then there is a separate bus line for circuits 1 and 2, and another bus line for circuits 3 and 4. A motherboard for only one MS-card is available as well, refer to chapter 2.1.1.
Dimensions: Connectors:
Euro-card 1 × Euro connector 4 × CIS connector
100 × 160 mm 32-pin, DIN 41612 13-pin, plug-in socket for MSC MSC motherboard 1.915.770.xx
Ordering Information:
E32
Date printed: 29.11.01
Professional Audio System Components
2.2.2
Power Supply
1.915.100 This power supply provides a regulated output of ±15 VDC at a maximum load of 1.5 A for audio circuits, plus a regulated 48 VDC output for the phantom powering of microphones. In addition, 30 V of unregulated DC are available as well. If a regulated 24 VDC supply is required, the stabilizer card 1.915.105.xx can be connected to the 30 VDC output. Each of the output voltages is derived from a separate secondary winding of the mains transformer and can be fine-adjusted.
The ±15 VDC supply is fully short-circuit proof and is protected against overvoltage and excess temperature. Short-circuit-protection is also effective in the 48 VDC section. The power supply has no on/off switch in the primary circuit. Such a switch, if needed, will have to be fitted separately.
OVER VOLTAGE U.I.T. SENSE STAB1 15 V 1.5 A U.I.T. SENSE STAB2 +15 V 1.5 A
~
2.5 A slow 1 A @ 200...240 V 2 A @ 100...140 V
(OPTION)
CROW BAR OVER VOLTAGE
STAB
100 V 240 V
2.5 A slow
CROW BAR
STAB
315 mA slow STAB
+48 V 0.2 A
0.8 A slow
30 V 0.5 A
Mains transformer and regulator electronics are housed in one rectangular unit fitting into the 19" Euro-card frame (1.918.318/319), occupying the space of 28M widths. For this purpose, a mounting kit 1.918.316 is recommended (see chapter 2.3.4).
Date printed: 29.11.01
E33
Professional Audio System Components
Technical Specifications Primary: Voltage selector Fuse Power consumption Secondary: Audio supply: Ripple Fuses Phantom supply: Ripple Fuse Unregulated DC: Fuse W×H×D Weight 100/120/140/200/220/240 VAC ±10% T 2 A (slow), 100...140 V T 1 A (slow), 200...240 V < 120 W (190 VA) ±15 V/1.5 A max., regulated voltage 100 µV 2 × T 2.5 A (slow) 48 V/200 mA max., regulated voltage, according to DIN 45596 100 µV T 315 mA (slow) 30 V/0.5 A max. T 0.8 A (slow) 140 × 100 × 160 mm, Euro-card/28M units 2.75 kg Power supply Mounting kit for installation in ELMA frame (1.918.318) 1.915.100.xx 1.918.316.xx
Dimensions:
Ordering Information:
E34
Date printed: 29.11.01
Professional Audio System Components
2.2.3
Audio Generator
1.915.200 This oscillator circuit provides a convenient source of 9 fixed audio frequencies with stable signal level, accommodated on one Euro-card. It is well suited for quick frequency-response measurements or for other calibration work in an audio system.
Two three-position rocker switches allow the selection of the 9 frequencies, a third switch permits changeover to an external Wien-bridge, if external frequency control should be desired. An output amplifier with level control on its input is also implemented, providing three different outputs, as far as levels and balanced/unbalanced configurations are concerned.
Date printed: 29.11.01
E35
Professional Audio System Components
Technical Specifications General: Frequencies Settling time Level accuracy Operating temperature Supply Output 1: balanced and floating Output level range Level uniformity vs. frequency THD Output impedance Minimum load Output 2: unbalanced Output level range Level uniformity vs. frequency THD Minimum load Output 3: balanced and floating Output level range Level uniformity vs. frequency THD Output impedance Minimum load Euro-card Weight 30 / 100 / 150 / 300 Hz / 1 / 1.5 / 3 / 10 / 15 kHz, fixed (accuracy ±5%) < 5 s (30 Hz) < 1 s (1 kHz) +0.1/0.2 dB (0...50° C) 10...+55° C ±15 V, regulated within ±0.2 V (< 25 mA) separately adjustable ...+10 dBu (0...2.45 Vrms) ±0.1 dB (20° C) < 0.25%, 30 Hz...15 kHz < 0.1%, 100 Hz...10 kHz < 30 200 separately adjustable ...+15 dBu (0...4.4 Vrms) ±0.2 dB (20° C) < 0.15%, 30 Hz...15 kHz < 0.1%, 100 Hz...10 kHz 200 separately adjustable ...50 dBu (0...2.5 mVrms) ±0.2 dB (20° C) < 0.2%, 30 Hz...15 kHz 12 200 100 × 160 mm, 7M units wide approx. 350 g Audio generator 30 Hz...15 kHz 1.915.200.xx
Dimensions:
Ordering Information:
E36
Date printed: 29.11.01
Professional Audio System Components
2.2.4
Monitor Amplifier and Switching Relays (Studio/CR)
1.915.304
The circuit on this Euro-card is designed to form part of an audio monitoring system. The card is narrower than most others, i.e., 4 M units only. It contains four amplifiers, each presenting a 0- input impedance, two metering amplifiers, and four relays for audio switching.
Two stereo signal inputs from a combination of sources (with suitable isolation resistors at the output of each source) can thus be summed for Control Room (CR) and Studio Monitoring, for example. In addition, the signal from the stereo master can be assigned to either monitor line and, if needed, CR monitoring and studio monitoring can be paralleled. A further circuit permits switchover of level meters from the master bus to the CR monitor line. The relays are designed for 6 VDC operation.
Date printed: 29.11.01
E37
Professional Audio System Components
Technical Specifications Inputs: Impedance Maximum level Outputs: Impedance Maximum level Maximum load Meter outputs: Maximum level Frequency response THD S/N Supply: Dimensions: Euro-card Connector system Weight balanced and floating (for CR monitor and studio monitor) > 10 k +24 dBu unbalanced (for CR monitor and studio monitor) <3 +20 dBu into 1 k 1 k push-pull +24 dBu ±0.5 dB, 30 Hz...16 kHz < 0.1%, @ +6 dBu input, 30 Hz...16 kHz 105 dB, 20 Hz...23 kHz ±15 V (20 mA) 100 × 160 mm, 4M units wide (19 mm) DIN 41612, type B approx. 270 g Monitor amplifier and switching relay 1.915.304.xx
Ordering Information:
E38
Date printed: 29.11.01
Studer Audio Components
Monitor Amp 1.915.304.00 ( 0)
Idx. Pos. 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 C1 C2 C3 C4 C5 C6 C7 C8 C9 C 10 D1 D2 D3 D4 IC 1 IC 2 IC 3 K1 K2 K3 K4 R1 R2 R4 R5 R7 R8 R9 R 10 R 11 R 12 R 13 R 14 R 15 R 16 R 17 R 18 R 19 R 20 R 21 R 22 R 23 R 24 R 25 R 26 R 27 R 28 R 29 R 30 T1 T2 T3 T4 Part No. 59.32.4471 59.25.4101 59.32.4471 59.25.4101 59.32.4471 59.25.4101 59.25.4101 59.25.4101 59.32.4471 59.25.4101 50.04.0125 50.04.0125 50.04.0125 50.04.0125 50.09.0107 50.09.0107 50.09.0107 56.04.0146 56.04.0146 56.04.0146 56.04.0146 57.11.3682 57.11.3393 57.11.3682 57.11.3393 57.11.3562 57.11.3562 57.11.3562 57.11.3562 57.11.3334 57.11.3562 57.11.3334 57.11.3562 57.11.3682 57.11.3393 57.11.3562 57.99.0206 57.99.0206 57.11.3682 57.11.3393 57.11.3562 57.11.3562 57.11.3562 57.11.3562 57.11.3562 57.11.3562 57.11.3562 57.11.3562 57.11.3562 1.022.419.00 1.022.419.00 1.022.419.00 1.022.419.00 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 Qty. pce pce pce pce pce pce pce pce pce pce pce pce pce pce pce pce pce pce pce pce pce pce pce pce pce pce pce pce pce pce pce pce pce pce pce pce pce pce pce pce pce pce pce pce pce pce pce pce pce pce pce pce pce Type/Val. 470p 100u 470p 100u 470p 100u 100u 100u 470p 100u 1N4448 1N4448 1N4448 1N4448 4559 4559 4559 4*u 4*u 4*u 4*u 6k8 39k 6k8 39k 5k6 5k6 5k6 5k6 330k 5k6 330k 5k6 6k8 39k 5k6 50R 50R 6k8 39k 5k6 5k6 5k6 5k6 5k6 5k6 5k6 5k6 5k6 Description CER , 20%, 50V EL 25V 20% axial CER , 20%, 50V EL 25V 20% axial CER , 20%, 50V EL 25V 20% axial EL 25V 20% axial EL 25V 20% axial CER , 20%, 50V EL 25V 20% axial 75V, 150mA, 4ns, DO-35 75V, 150mA, 4ns, DO-35 75V, 150mA, 4ns, DO-35 75V, 150mA, 4ns, DO-35 Dual Op-Amp Dual Op-Amp Dual Op-Amp 6V, 220V/2A, PCB 6V, 220V/2A, PCB 6V, 220V/2A, PCB 6V, 220V/2A, PCB MF, 1%, 0207 MF, 1%, 0207 MF, 1%, 0207 MF, 1%, 0207 MF, 1%, 0207 MF, 1%, 0207 MF, 1%, 0207 MF, 1%, 0207 MF, 1%, 0207 MF, 1%, 0207 MF, 1%, 0207 MF, 1%, 0207 MF, 1%, 0207 MF, 1%, 0207 MF, 1%, 0207 PTC, 25V, 0.5W PTC, 25V, 0.5W MF, 1%, 0207 MF, 1%, 0207 MF, 1%, 0207 MF, 1%, 0207 MF, 1%, 0207 MF, 1%, 0207 MF, 1%, 0207 MF, 1%, 0207 MF, 1%, 0207 MF, 1%, 0207 MF, 1%, 0207 EINGANGSTRAFO 1:1 EINGANGSTRAFO 1:1 EINGANGSTRAFO 1:1 EINGANGSTRAFO 1:1 Idx. Pos. Part No. Qty. Type/Val. Description
Page: 1 of 1
End of List Comments:
Date printed: 06.11.2006
Professional Audio System Components
2.2.5
Distribution Amplifier
1.915.307/308
The distribution amplifier cards offer splitting of one input to four or six individually adjustable outputs (versions 1.915.308 or 1.915.307, respectively). The input and all outputs are transformer-balanced and floating. These cards satisfy any complex requirement of signal routing and distribution.
Date printed: 29.11.01
E39
Professional Audio System Components
Technical Specifications General: Frequency range Frequency response 31.5 Hz...16 kHz +0.2/0.5 dB, RL = 300 balanced and floating 10 k 60 dB 20...+10 dB (Jumper 2-3: +6 dB Gain) balanced and floating 40 +24 dBu, RL = 600 /THD < 1% +21 dBu, RL = 200 /THD < 1% 0.02%, +6 dBu/300 100 dBu, 0 dB gain ±15 VDC (90 mA, all outputs +6 dBu, without load; 180 mA, all outputs +24 dBu into 300 ) Euro-card Weight 100 × 160 mm, 7 M units wide 500 g (1.915.308) 600 g (1.915.307)
Input: Impedance Symmetry Gain, adjustable Outputs: Impedance Maximum level THD Output noise voltage Supply:
Dimensions:
Ordering Information: Euro-cards: 19"/1U standard products:
· · · · ·
Distribution amplifier 1 to 6 Distribution amplifier 1 to 4 Distribution unit 2 × 1 in/4 out on XLR Distribution unit 3 × 1 in/4 out on XLR Distribution unit 2 × 1 in/6 out on XLR
1.915.307.xx 1.915.308.xx 75.700.89301 75.700.89302 75.700.89303
E40
Date printed: 29.11.01
Professional Audio System Components
2.2.6
5 W Power Amplifier
1.915.410/415
This amplifier on one Euro-card is designed for operation on a ±15 V supply. It is capable of providing a power output of 5 W into a load of 8 . With its low-to-medium power level, this amplifier is ideally suited for applications such as pre-listening or talkback speaker operation. Its output stage is protected by instantaneous output power limiting.
· · · · ·
The standard version has an electronically balanced (transformerless) input. It is also available with the following options: Input balancing transformer Remote muting Remote gain control (VCA) Input balancing transformer plus remote muting Input balancing transformer plus remote gain control (VCA).
Date printed: 29.11.01
E41
Professional Audio System Components
Technical Specifications Audio: Power output 4 W/15 5 W/8 2.5 W/4 , continuous, sine wave < 0.1% @ rated output, 30 Hz...16 kHz ±0.5 dB, 30 Hz...16 kHz 10 k, balanced 17...+16 dBu (0.11...4.9 Vrms) for rated output +24 dBu (12.3 Vrms) clipping point 100 dB, linear to 23 kHz at normal operating gain (input +6 dBu) 85 dB, at maximum gain ±15 V DC (40 mA idling; 400 mA @ 5 W/8 ) 23 mA 100 × 160 mm, 7M units wide approx. 210 g
THD Frequency response Input impedance Sensitivity Maximum input level S/N
Supply: Output stage quiescent current Dimensions: Euro-card Weight
Ordering Information: 5 W amplifier with
· · · · · ·
transformerless input input transformer transformerless input and remote muting facility input transformer and remote muting facility transformerless input and remote gain control (VCA) input transformer and remote gain control (VCA)
1.915.410.xx 1.915.411.xx 1.915.412.xx 1.915.413.xx 1.915.414.xx 1.915.415.xx
E42
Date printed: 29.11.01
Professional Audio System Components
2.2.7
40 W Power Amplifier
1.915.440/441
For applications where higher power level is needed, a 40 W amplifier has been realized on a Euro-card. Its width is 32 mm, which equals 7M widths approximately.
Power is supplied from a separate 45 VDC source, as is contained in the 19" mounting frame 1.918.120.xx. Two amplifier cards will fit into that frame, making it suitable for applications where stereophonic monitoring is required. Special Features · · · · · · · Transformerless version with electronically balanced inputs standard Version with balanced and floating inputs available Output stage protected from overload by momentary power limiting Temperature sensing avoids thermal overload High-end frequency response limited to prevent transient intermodulation distortion Low distortion performance, even at low power output Operation with output transformer possible
Date printed: 29.11.01
E43
Professional Audio System Components
Technical Specifications Audio: Power output THD Output impedance Input impedance Common mode rejection Input sensitivity Frequency response S/N 40 W/4 , continuous, sine-wave, < 0.1 %, 30 Hz...15 kHz (up to rated output) 0.1 10 k > 50 dB, 30 Hz...16 kHz (with input transformer) 12...+18 dBu (0.195...6.2 Vrms) for rated output (adjustable with jumper in three 10 dB-increments, plus fine-trim range of 12 dB) +0.5/1 dB, 30 Hz...15 kHz 105 dB @ maximum gain 90 dB @ minimum gain 45 VDC (70 mA idling, 1.5 A @ 40 W/4 ) Euro-card 100 × 160 mm, 7M units wide
Supply: Dimensions: Ordering Information: Euro-cards 19"/1U standard products 40 W power amplifier
· · · · ·
40 W power amplifier with transformerless input 40 W power amplifier with input transformer Mono version, 19"/1U Stereo version, 19"/1U 19"/1U mounting frame (without amplifier cards)
1.915.440.xx 1.915.441.xx 75.700.80311 75.700.80322 1.918.120.xx
E44
Date printed: 29.11.01
Professional Audio System Components
2.2.8
Monitor Switching Relays
1.915.601/602
Two different monitor circuit switching cards are available. They are equipped with either five or eight relays for switching of a corresponding number of stereo sources to one or two stereo outputs in monitor circuits.
The relays are available with coil ratings of 6 VDC or 24 VDC, depending on the user's requirement. Click-suppressing diodes are wired across each relay coil. The relays are equipped with four double throw (change-over) contacts each.
Isolation of the monitor lines from external circuitry is achieved by 5.6 k resistors in the "a" and "b" legs of each stereo line, thus a high impedance (bridging) load is presented to the outside source, even in deenergized (non-selected) status, when the respective pair of relay contacts shorts the lines after the respective isolation resistors. With a relay energized, the corresponding stereo pair is routed to a stereo bus available on four pins of the 32-contact edge connector (in case of the 5-input card 1.915.601.xx).
Date printed: 29.11.01
E45
Professional Audio System Components
Card 1.915.602.xx features a similar circuit configuration with eight relays, to switch one unbalanced and three balanced stereo inputs. Two stereo buses appear on eight pins of the edge-connector; in this way, the four inputs can be switched to either one or to both outputs, such as may be the case with separate monitor circuits in the control room and in the studio.
Dimensions:
Euro-card Weight · ·
100 × 160 mm, 4 M units wide approx. 250 g Relay card, 5 IN/1 OUT Relay card, 4 IN/2 OUT 1.915.601.xx 1.915.602.xx
Ordering Information:
E46
Date printed: 29.11.01
Professional Audio System Components
2.2.9
Transistor-Driven Relays (7+2)
1.915.603
This Euro-card is supplied with nine transistor-driven relays with singlepole, double-throw (SPDT) contacts. For two of the relays, both normally-open and normally-closed contacts are routed to the edge connector; for the remaining seven it is jumper-selectable whether the normally-open or the normally-closed contact is used.
The relays are designed for operation on 6 VDC, and each relay coil is bridged with a click-suppressing diode. PNP transistors in series with the coils are blocking the current flow, because each transistor is normally biased off. By applying the output from the gate of an external control logic to the base of a transistor, it is switched into saturation, thereby energizing the respective relay. This arrangement of nine relays was designed for use in signaling systems within a studio installation; however, it may find its use for other applications as well.
MAKE OR BREAK CONTACTS (7 ×) CHANGE-OVER CONTACTS (2 ×)
4k7 10k 10k
4k7
6V
6V
Polarity of the relay's supply voltage must be observed when utilizing this circuit.
Date printed: 29.11.01
E47
Professional Audio System Components
Technical Specifications Contact Ratings: Note: Switching power max. 1 A/30 VDC or 0.3 A/125 VAC In this application 48 V must not be exceeded to avoid shock hazard. 60 VA (AC) 100 W (DC) 100 × 160 mm, 4 M units wide Transistor-driven relays 1.915.603.xx
Dimensions: Ordering Information:
Euro-card
E48
Date printed: 29.11.01
Professional Audio System Components
2.2.10
Dual Limiter
1.915.700 In sound work there are numerous situations where the signal amplitude has to be limited to a pre-determined level in order to prevent overloading of succeeding equipment, such as light modulators in film work, or radio transmitters. With this limiter, excessive levels are automatically reduced to a preset level, and, since regulation is controlled by the program's energy content, the performance of this limiter is free of any "pumping" effects. Gain reduction is achieved with a Studer Voltage Controlled Amplifier (VCA) which ensures low noise performance and negligible distortion.
Two identical, independent limiter circuits are contained on one Eurocard, plus additional, separate gain stages to drive peak program meters. The perfect tracking of the two VCAs makes this Dual Limiter suitable for stereo work as well, in which case a simple electrical connection is needed to link the units.
Note:
Date printed: 29.11.01
Gain reduction meters (not supplied) can be connected to the LINK outputs as well, if required.
E49
Professional Audio System Components
Technical Specifications Input: Impedance Overload point Output: Impedance Frequency response Gain Output noise level Limiting ratio Threshold Limited output level Attack time Release time PPM Section: Output impedance Maximum output level Gain Frequency response Supply: Dimensions: Ordering Information: Euro-card 5.4 k, balanced configuration 2.7 k, unbalanced configuration +20 dBu (7.75 Vrms) < 50 , unbalanced +0/0.5 dB, 30 Hz...15 kHz +0/3 dB, 2 Hz...200 kHz 0 dB, limiter off 102 dBu, Limiter on 106 dBu, Limiter off 20:1 15 dBu...+3 dBu, adjustable 14 dBu...+4 dBu, depending on threshold setting 1 ms 50 ms...5 s, program-dependent < 50 , unbalanced +20 dBu 2.5 dB...27 dB, adjustable +0/3 dB, 2 Hz...200 kHz ±15 V (100 mA) 100 × 160 mm, 7 M units wide Dual limiter 1.915.700.xx
E50
Date printed: 29.11.01
Professional Audio System Components
2.2.11
Telephone Hybrid
1.915.760/764
In order to record or transmit a conversation between the announcer in the studio and a person outside the studio being interviewed by telephone, the telephone line must be connected to the mixing console. In such a case, the full conversation is transmitted, since both voice signals are carried on normal 2-wire telephone lines. However, also the voice of the announcer in the studio is then transmitted in telephone quality (300... 3400 Hz). By mixing the microphone signal of the announcer (in studio quality) to the conversation, the addition of the "good" and "poor" signals results in a distorted and untrue signal.
Principle of a telephone transmission via a mixing console
The telephone hybrid allows to greatly improve the quality of a telephone transmission by selectively suppressing the undesired "poor" announcer signal (side-tone attenuation). This side-tone attenuation is done in principle by a hybrid circuit which is a familiar feature in telephony.
Date printed: 29.11.01
E51
Professional Audio System Components
The Studer telephone hybrid permits high-quality transmission of telephone conversations with the announcer in the studio. Apart from connecting it to the telephone line, the hybrid works automatically. Maximum side-tone attenuation of the studio voice signal in the receiver line is achieved by automatically constituting a dummy load for the telephone line. This adjustment is performed electronically, the rea