Text preview for : Sony-STS5 tun.pdf part of Sony STS5 tuner
Back to : Sony-STS5 tun.rar | Home
ST-S5
SERVICE MANUAL
Ver 1.0 2001.04
AEP Model UK Model E Model Australian Model
ST-S5 is the tuner section in MHC-S7AV.
SPECIFICATIONS
Tuner section
FM stereo, FM/AM superheterodyne tuner
FM tuner section
Tuning range Antenna Antenna terminals Intermediate frequency
AM tuner section
87.5 108.0 MHz FM lead antenna 75 ohm unbalanced 10.7 MHz
Tuning range AEP, UK models: Other models:
Antenna Antenna terminals Intermediate frequency Dimensions (w/h/d) Mass
531 1,602 kHz (with the interval set at 9 kHz) 531 1,602 kHz (with the interval set at 9 kHz) 530 1,710 kHz (with the interval set at 10 kHz) AM loop antenna External antenna terminal 450 kHz Approx. 280 x 108 x 340 mm Approx. 2.1 kg
Design and specifications are subject to change without notice.
FM STEREO/FM-AM SUPERHETERODYNE TUNER
9-873-832-11
2001D0500-1 C 2001.4
Sony Corporation
Home Audio Company Shinagawa Tec Service Manual Production Group
ST-S5
TABLE OF CONTENTS 1. 2. SERVICING NOTES ................................................ 3 GENERAL
Location of Controls ....................................................... 4 Setting the Time .............................................................. 5
Notes on chip component replacement · Never reuse a disconnected chip component. · Notice that the minus side of a tantalum capacitor may be damaged by heat.
SAFETY-RELATED COMPONENT WARNING!! COMPONENTS IDENTIFIED BY MARK 0 OR DOTTED LINE WITH MARK 0 ON THE SCHEMATIC DIAGRAMS AND IN THE PARTS LIST ARE CRITICAL TO SAFE OPERATION. REPLACE THESE COMPONENTS WITH SONY PARTS WHOSE PART NUMBERS APPEAR AS SHOWN IN THIS MANUAL OR IN SUPPLEMENTS PUBLISHED BY SONY.
3.
3-1. 3-2. 3-3. 3-4. 3-5. 3-6. 3-7.
DISASSEMBLY
Disassembly Flow ........................................................... Cover ............................................................................... Front Panel Section ......................................................... PANEL Board, SIRCS Board ......................................... Tuner pack (FM/AM) ...................................................... MAIN Board ................................................................... DSP Board ....................................................................... 6 7 7 8 8 9 9
4. 5.
TEST MODE .............................................................. 10 DIAGRAMS
11 12 13 14 15 16 17 18 19 21
5-1. Note for Printed Wiring Boards and Schematic Diagrams ....................................................... 5-2. Schematic Diagram MAIN Board (1/2) .................. 5-3. Schematic Diagram MAIN Board (2/2) .................. 5-4. Printed Wiring Board MAIN Board ........................ 5-5. Printed Wiring Board DSP Board ............................ 5-6. Schematic Diagram DSP Board (1/2) ..................... 5-7. Schematic Diagram DSP Board (2/2) ..................... 5-8. Printed Wiring Boards PANEL Section .................. 5-9. Schematic Diagram PANEL Section ....................... 5-10. IC Pin Function Description ...........................................
6.
EXPLODED VIEWS
6-1. Cover, Front Panel Section ............................................. 28 6-2. Chassis Section ............................................................... 29
7.
ELECTRICAL PARTS LIST ............................... 30
2
ST-S5 SECTION 1 SERVICING NOTES
This set is a component of the MHC-S7AV. The MHC-S7AV system configuration is as shown below, and therefore it does not operate normally unless all four components are connected. In performing the repair, connect all components with the system cables. Note: The precaution to the users is described on the label stuck on the back panel (CD player) and in the troubleshooting section in the Operation Manual. System Configuration: · MODEL IDENTIFICATION Rear Panel
PART No.
TA
POWER SUPPLY
AC IN
MODEL AEP and UK models Australian model Mexican model Korean model
PART No. 4-232-327-0[] 4-232-327-1[] 4-232-327-4[] 4-232-327-9[]
ST
SYSTEM & CD µcon DISPLAY
CDP TC
TC µcon
3
ST-S5 SECTION 2 GENERAL
LOCATION OF CONTROLS
Front Panel This section is extracted from instruction manual.
qh
qjqk ql w;
+ +
wh
wg wf
wd ws wa
CLOCK/TIMER wg (13, 21, 29) DISPLAY qh (13, 16, 18, 29, 35) ENTER w; (17, 18) IR receptor wh PRESET +/ ws (17, 18) PTY (AEP, UK models only) wa (18) STEREO/MONO qj (17) TIMER SELECT wf (22, 30) TUNER/BAND wd (17) TUNER MEMORY qk (17) TUNING +/ ql (17)
Rear Panel
1
1 ANTENNA terminal 2 SYSTEM CONTROL 1 connector (TO TA-S7AV) 3 SYSTEM CONTROL 2 connector (TO TA-S7AV) 4 SYSTEM CONTROL 3 connector (FROM CDP-S3) 5 OPTICAL IN terminal 6 OPTICAL IN terminal (FROM CDP-S3) 7 SYSTEM CONTROL 4 connector (TO TC-S3) 8 OPTICAL OUT terminal 9 SUB WOOFER OUT jack
2 3
4
5 6 7 8 9 0 qa
0 MD IN/OUT jack qa VIDEO (AUDIO) IN jack
4
ST-S5
Remote Control
Setting the time
1 2
Turn on the system. Press CLOCK/TIMER (or CLOCK/TIMER SET on the remote).
1 2 3
When you set the time for the first time, proceed to step 5.
es ea e; wl wk wj wh wg wf wd ws wa w; ql qk
H hH hH
. m
> M
x X
O P o p
4 5 6 7 8 9 q; qa qs qd qf qg qh qj
3 4 5 6 7 8
Tip
Press O or o repeatedly to select "CLOCK SET". Press ENTER (A/V amplifier or remote). Press O or o repeatedly to set the hour. Press ENTER (A/V amplifier or remote). Press O or o repeatedly to set the minutes. Press ENTER (A/V amplifier or remote).
If you have made a mistake or want to change the time, start over from step 2.
Note
The clock settings are canceled when you disconnect the power cord or if a power failure occurs.
CD H es (14, 15) CHECK 5 (15) CLEAR 6 (15) CLOCK/TIMER SELECT qj (30) CLOCK/TIMER SET qk (13, 21, 29) DBFB qg (23) DISPLAY ws (13, 16, 18, 29, 35) D.SKIP 4 (14) ENTER wg (10, 12, 13, 15, 17, 18, 21, 22, 2630) EQ qd (27) EQ ON/OFF qf (10, 28) FUNCTION wf (10, 14, 15, 20, 21, 31) GROOVE wa (23) SET UP qs (10, 12, 26, 28, 29) SLEEP 7 (29) SUR wd (25) TAPE A hH ea (19, 35) TAPE B hH e; (19, 20, 35)
TUNER/BAND wl (17) TUNING + 9 (17) TUNING wh (17) TV CH +/ ql TV VOL +/ w; TV @/1 2 TV/VIDEO 1 VOL +/ qh BUTTON DESCRIPTIONS @/1 (power) 3 X (pause) q; x (stop) 8 . (go back) wk > (go forward) wj m (rewind) wh M (fast forward) 9 O/o/P/p qa
5
ST-S5 SECTION 3 DISASSEMBLY
· This set can be disassembled in the order shown below.
3-1.
DISASSEMBLY FLOW
SET
3-2. COVER (Page 7)
3-3. FRONT PANEL SECTION (Page 7)
3-5. TUNER PACK (FM/AM) (Page 8)
3-7. DSP BOARD (Page 9)
3-4. PANEL BOARD, SIRCS BOARD (Page 8)
3-6. MAIN BOARD (Page 9)
6
ST-S5
Note: Follow the disassembly procedure in the numerical order given.
3-2.
COVER
3 cover 1 screw (+BVTT3 × 6 (S))
2 two screws (case 3 TP2)
2 two screws (case 3 TP2)
3-3.
FRONT PANEL SECTION
1 wire (flat type) (19 core) (CN502)
3 two claws 4 front panel section
3 two claws 3 claw
2 three screws (BVTP3 × 8)
7
ST-S5
3-4.
PANEL BOARD, SIRCS BOARD
2 two screws (BVTP2.6 × 8) 6 SIRCS board 4 PANEL board 2 four screws (BVTP2.6 × 8)
5 two claws
2 screw (BVTP2.6 × 8) (AEP, UK models)
1 wire (flat type) (19 core) (CN602)
3 two claws
3-5.
TUNER PACK (FM/AM)
3 tuner pack (FM/AM)
1 wire (flat type) (11 core) (Korean, Mexican and Australian models) wire (flat type) (15 core) (AEP, UK models) (CN506)
2 two screws (BVTP3 × 8)
8
ST-S5
3-6.
MAIN BOARD
1 wire (flat type) (23 core) (CN508) 1 wire (flat type) (21 core) (CN509)
2 five connectors (CN510, 5031, 5032, 5041, 5042)
6 MAIN board 4 screw (BVTP3 × 8) 4 two screws (BVTP3 × 8)
1 wire (flat type) (19 core) (CN502) 3 three screws (BVTP3 × 8)
5 PC board holder 2 connector (CN601)
3-7.
DSP BOARD
1 wire (flat type) (23 core) (CN603) 4 three screws (BVTP3 × 8)
6 DSP board 3 three screws (BVTP3 × 8)
1 wire (flat type) (21 core) (CN602)
2 connector (CN601)
5 PC board holder
9
ST-S5 SECTION 4 TEST MODE
Note: Use flowing buttons in the test mode. no mark : Button of tuner unit (ST-S5) *1 : Button of amplifier unit (TA-S7AV) *2 : Button of CD unit (CDP-S3)
[MC Cold Reset] · The cold reset clears all data including preset data stored in the RAM to initial conditions. Execute this mode when returning the set to the customer. Procedure 1: 1. Press the ?/1 *1 button to turn the power ON. 2. While pressing the [DIGITAL] * 1 button, press the [DISPLAY] button. 3. The set is reset, and becomes standby state. Procedure 2: 1. Press the ?/1 *1 button to turn the power ON. 2. While pressing the both [PLAY MODE]*2 and x *2 buttons, press the M *2 button. 3. The set is reset, and becomes standby state. [MC Hot Reset] · This mode resets the set with the preset data kept stored in the memory. The hot reset mode functions same as if the power cord is plugged in and out. Procedure 1: 1. Press the ?/1 *1 button to turn the power ON. 2. While pressing the both [STEREO/MONO] and [CINEMA STUDIO C]*1 buttons, press the [TIMER SELECT] button. 3. The set is reset, and becomes standby state. Procedure 2: 1. Press the ?/1 *1 button to turn the power ON. 2. While pressing the both [PLAY MODE]*2 and x *2 buttons, press the m *2 button. 3. The set is reset, and becomes standby state. [Change-over the AM Tuning Interval] (EXCEPT AEP and UK models) · The AM tuning interval can be changed over 9 kHz or 10 kHz. Procedure: 1. Press the ?/1 *1 button to turn the power ON. 2. Turn the [FUNCTION] *1 knob to select "TUNER", and press the [TUNER/BAND] button to select the BAND "AM". 3. Press the ?/1 *1 button to turn the power OFF. 4. While pressing the [ENTER] button, press the ?/1 *1 button, and the display on the fluorescent indicator tube changes to "AM 9 K STEP" or "AM 10 K STEP", and thus the tuning interval is changed over. [Change-over of VACS ON/OFF] 1. Press the ?/1 *1 button to turn the power ON. 2. While pressing the both [STEREO/MONO] and [CINEMA STUDIO C]*1 buttons, press the [CINEMA STUDIO B] button, and VACS ON/OFF is change over.
[GC Test Mode] Enter the GC Test Mode mode Procedure 1: 1. Press the ?/1 *1 button to turn the power ON. 2. While pressing the both [STEREO/MONO] and [CINEMA STUDIO C]*1 buttons, press the [CLOCK/TIMER] button. 3. LEDs and fluorescent indicator tube are all turned on of all units. Procedure 2: 1. Press the ?/1 *1 button to turn the power ON. 2. While pressing the both [PLAY MODE]*2 and x *2 buttons, press the Z (DISC 1)*2 button. 3. LEDs and fluorescent indicator tube are all turned on of all units. Version Display Mode Procedure: 1. Enter the GC test mode. 2. Each time the [TUNER MEMORY] or [DISC 1]*2 button is pressed, microcomputer or mechanism deck version is displayed of each unit. 3. Press the [TUNING +] or [DISC 3]*2 button to detail is displayed the version. Key Check Mode Procedure: 1. Enter the GC test mode. 2. Press the [TUNING -- ] or [DISC 2]*2 button to set the key check mode. 3. In the key check the mode, the fluorescent indicator tube displays "K 0 J 0 V 0" . Each time a button is pressed, "K" value increases. However, once a button is pressed, it is no longer taken into account. VACS Level Display Mode Procedure: 1. Enter the GC test mode. 2. Press the [TUNING +] or [DISC 3]*2 button to display VACS level on the fluorescent indicator tube. Segment Check Mode Procedure: 1. Enter the GC test mode. 2. Press the [ENTER] or x *2 button to set the segment check mode. 3. In the segment check the mode. Each [ENTER] or x *2 button is pressed, the fluorescent indicator tube displays is switching variously. Releasing the GC Test Mode · To release from this mode, press three buttons in the same manner as entering this mode or disconnect the power cord.
10
ST-S5 SECTION 5 DIAGRAMS
5-1. NOTE FOR PRINTED WIRING BOARDS AND SCHEMATIC DIAGRAMS
Note on Schematic Diagram: · All capacitors are in µF unless otherwise noted. pF: µµF 50 WV or less are not indicated except for electrolytics and tantalums. · All resistors are in and 1/4 W or less unless otherwise specified. f : internal component. · · 5 : fusible resistor. · C : panel designation. Note: The components identified by mark 0 or dotted line with mark 0 are critical for safety. Replace only with part number specified. · A : B+ Line. · B : B Line. · Voltages and waveforms are dc with respect to ground under no-signal (detuned) conditions. no mark : TUNER (FM/AM) ( ) : CD PLAY : AC OFF : Impossible to measure · Voltages are taken with a VOM (Input impedance 10 M). Voltage variations may be noted due to normal production tolerances. · Waveforms are taken with a oscilloscope. Voltage variations may be noted due to normal production tolerances. · Signal path. F : TUNER (FM/AM) E : TAPE PLAY G : RECORD J : CD PLAY c : DIGITAL INPUT N : MIC INPUT · Abbreviation AUS : Australian model KR : Korean model MX : Mexican model
· Circuit Boards Location
DSP board
Note on Printed Wiring Board: · X : parts extracted from the component side. · Y : parts extracted from the conductor side. · : Pattern from the side which enables seeing. (The other layers' patterns are not indicated.) Caution: Pattern face side: (Conductor Side) Parts face side: (Component Side)
TUNER PACK
Parts on the pattern face side seen from the pattern face are indicated. Parts on the parts face side seen from the parts face are indicated.
· Indication of transistor.
C Q B E These are omitted.
Q B C E These are omitted.
SIRCS board MAIN board
Q B C E These are omitted.
PANEL board
11
11
ST-S5
5-2. SCHEMATIC DIAGRAM MAIN Board (1/2)
(1/2)
CN5031 5P M(A)-GND EVER+5V D-GND D+5V NO901 3P NO991 3P C991 0.1 G
I +15V REGULATOR O IC991 NJM7815FA
(Page 13)
CN5041 10P MIC-SIG MIC-GND FL-OUT FRONT-GND AA4 FR-OUT AA3 CENTER-OUT CENTER-GND (A-GND) AA5 AA6
C992 0.1
(Page 13)
AA2 SL-OUT S-GND AA1 SR-OUT 1 2 3 OPTICAL RECEIVER VCC C955 10000p GND R951 470 4 5 6
OPTICAL IN (FROM CDP-S3)
OUT IC951 TORX178B
OPTICAL RECEIVER VCC OPTICAL IN GND
C957 10000p
OUT IC952 TORX178B R952 470 L951 220µH 7 8 (CHASSIS) NO507 4P C916 10000p 9
AB20
C964 10000p
C956 10 50V
AB21
10
(Page 16)
REC OUT-R PB-R TC A-GND PB-L
CN510 5P
BB1 BB2
BB3 BB4
REC OUT-L C977 10 50V +10V REGULATOR DD1 DD2 VCD L-IN BB3 TC L-IN BB4 TC REC L-OUT A-GND BB1 TC REC R-OUT BB2 TC R-IN DD3 VCD R5-IN C978 10 50V TUNER R-IN A+10V AA6 MIC-IN A-GND AA5 FL-OUT C966 10000p C905 470 16V C904 3300 16V C952 4700 25V DD4 D901 D3SBA20 C953 0.1 R943 3.3k C941 10 50V D942 1SS133T R942 1k D941 1SS133T R941 1k L955 470µH IC903 NJM7810FA O G I 11
SYSTEM CONTROL 4 (TO TC-S3) TUNER L-IN CN508 23P
(Page 13)
(Page 17)
F-GND AA4 FR-OUT A-GND AA2 +5V REGULATOR IC904 µPC7805AHF
DBFB FEEDBACK
LS-OUT S-GND AA1 RS-OUT C-GND AA3 C-OUT LINE-MUTE DBFB FEEDBACK
O G
I
D922 11ES2
C907 220 10V
D903 11ES2 C906 0.1 D904 11ES2
D923 11ES2 CN509 21P D-GND D-OUT D-GND E8 DSP-DECODE E7 DSP-CS E9 AMP-DATA E6 DSP-ACK AMP-CLK E5 CODEC-SMUTE E11 AMP-LAT E4 DIR-Rx E12 DIG-Tx I G E3 DIR-XSTATE E13 DSP-Rx E2 DIR-CS E14 DIG-CLK DIR-UNLOCK D-GND D+5V C968 10000p A-GND A+5V R912 510 C903 10 50V C918 470 10V C551 10 50V C552 0.1 R553 47k D552 1SS133T 13 E1 C971 10000p R911 220 Q551 2SC2603 RESET SWITCH O Q902 2SC2001-K1K2 +3.3V REGULATOR RESET SIGNAL GENERATOR IC551 M51943BSL E10 C902 470 10V 12 D920 11ES2-NTA2 +7V REGULATOR IC901 TA78057S O G I R551 470 R552 10k R555 4.7k
D551 1SS133T-72
C553 0.1
R554 47k
(Page 16)
C970 10000p
14 15 16 17
12
12
ST-S5
5-3. SCHEMATIC DIAGRAM MAIN Board (2/2) · See page 20 for Waveforms.
(2/2)
CN506 15P (AEP,UK) 11P (E,AUS) CL (AEP,UK) MC D0 ST-DOUT MC D1 COAXIAL FM 75 CE A+10V R958 100 TUNED R959 100 FM ANTENNA 75 FM/AM TUNER UNIT * (E,AUS) ANALOG-GND R962 2.2k R-CH ST-MUTE MUTE AM D+5V N.C RDS-INT RDS-INT RDS-DATA RDS-DATA (AEP,UK) 1 I-CLK BLOCK 2 I-DAT 3 4 M-RESET 5 6 MRESET EVER+5V CD D(M)-GND R966 100 I2C-DATA V-MUTE R965 100 I2C-CLK JW95 UNREG TC D-GND SYSTEM CONTROL 3 (FROM CDP-S3) (AEP,UK) TC M-GND TC M-GND * SUPPLIED WITH THE ASSEMBLED D902 11ES2-NTA2 DD3 VCD R-IN HAKO-GND R963 5.6k DD4 DD2 CN505 17P VCD L-IN CD A-GND STEREO R961 2.2k L-CH STE C961 0.1 TUN C962 10 50V ST-CE R957 100 ST-DIN ST-CLK
R964 5.6k
DD1
D921 1SS133T-72
C909 100 50V
C915 100 35V R908 1k
D912 MTZJ-T72-30B
C910 10 50V
R904 10k
R905 100
CD D(M)-GND AB1 AC-LOW AB2 AC-LOW
D913 MTZJ-T-72-5.6B
R906 100
C937 0.1
D911 11ES2 -NTA2
R903 10
Q901 2SB734-3 -28V REGULATOR
CN502 19P DISPLAY/STANDBY KEY VF VF -VP
7 JOG2-B 8 JOG2-A 9 POWER KEY JOG1-B
D-GND JOG2-B JOG2-A JOG1-B JOG1-A JOG1-A R549 3.3k D943 1SS133T VOLA VOLA VOLB VOLB C506 4.7 50V M-RESET R558 1M R550 100k D944 1SS133T Q502 BN1A4M MUTING CONTROL SWITCH Q503 BN1A4M AC OFF C510 4.7 50V MUTING R557 22k DRIVER R532 47k C942 470 6.3V C943 0.1 SIRCS SIRCS R524 47k RESET I-DAT IIC-DATA I-CLK IIC-CLK KEY1 KEY1 D+3.3V D-GND EVER+5V(SIRCS)
10
(Page 19)
D945 1SS133T 11
EX-CLK
EX-OUT
EX-LAT
EX-IN
DBFB FEEDBACK
CN5042 9P DBFB FEEDBACK HAKO-GND
SYSTEM CONTROL 2 (TO TA-S7AV)
R534 100 E2
R537 100 E5
R536 100 E4
R535 100 E3
R533 100 E1
E6
R531 100
R556 47k
POWER KEY C561 0.1 EPT901 EX-CLK EXP-CLK EX-LAT EXP-LAT EX-OUT R956 100 EXP-OUT DATA EX-IN EXP-IN DATA KEY1 KEY0 TA POWER KEY
R528 100
R527 100
R538 100
R530 100
(Page 12)
DISPLAY KEY CODEC DIR-XSTATE -SMUTE DIR-UNLOCK POWER KEY DIR-RX DIR-CS LINE-MUTE VSS SOFT-TEST VCC EXP-CLK EXP-OUT DATA EXP-IN DATA EXP-LAT
DSP-ACK R539 100 DSP-CS E8 DSP-DECODE R540 100 E7
R526 100
UNREG
NO-USE
JOG2-B JOG2-A
CN5032 15P JOG2-B(F-SELECT) JOG2-A(F-SELECT)
(CHASSIS)
(Page 12)
SYSTEM CONTROL 1 (TO TA-S7AV)
JOG1-B R541 47k STE STEREO TUN R542 47k TUNED R522 10k R544 4.7k * R545 10k (AEP,UK) 4.7k (KR,AUS) 1k (MX) * R546 150 (KR,AUS) 4.7k (MX) C508 10 50V 12 R548 4.7k C509 0.1 VREF R546 * (E,AUS) R545 * V-MUTE AVSS CC2 NO-USE CC3 NO-USE CC4 CT R543 150 SYSTEM CONTROLLER MODEL-IN SPEC-IN IC501 M30622MGA-A39FP M-RESET C562 10000p AB2 AB1 AC LOW VP VF VF CT C972 0.1 AC LOW AB20 AC HIGH AB21 AC HIGH R523 100 JOG1-B(FUNCTION) JOG1-A JOG1-A(FUNCTION) VOLA VOLA M-RESET VOLB VOLB
AMP-DATA
RDS-DATA
AVCC ACCUT
NO-USE
EPT902 CC1 C928 0.1 C927 0.1
(Page 12)
(CHASSIS)
AMP-CLK
AMP-LAT
ST-MUTE
ST-DOUT
RDS-INT
DIG-CLK
DSP-RX
ST-CLK
ST-DIN
XCOUT
VCC
ST-CE
NMI
IIC CLK
DIG-TX
CNVSS
NO-USE
RESET
SIRCS
GND
XCIN
XOUT
VSS
XIN
IIC DATA CN503 10P GND CC1 TXD1/CAN'T USE C519 100p CC2 RTS1 NC
R509 330k
R502 100
R503 100
R504 100
R505 100
R506 100
R507 100
R512 100
R513 100
R514 100
32.768 kHz
(E,AUS)
R510 330
R511 10k
R515 1k
R516 100
R517 100
R518 100
R519 10k R520 10k
+5V CC3 CC4 CC5 CNVSS CC6 R521 100 RESET GND R525 100 CLK1/SQ-CLK R529 100 RXD1/SQ-DATA-IN (FOR TEST)
X501
X502 16MHz
R508 10k
RDS-DATA
C501 18p
C502 15p
I-CLK
I-DAT
E11
E10
E12
E13
E14
C504 0.1
JW501 JW502
R501 100
C503 0.1
ST-MUTE
RDS-INT
ST-DOUT
SIRCS 13
ST-CE
C505 1000 6.3V
ST-CLK
ST-DIN
C520 100p
E9
CN501 4P D-GND D+5V I-CLK (FOR TEST) IIC-CLK IIC-DATA
14 CC5 15 16 17 CC6 I-DAT
(CHASSIS)
13
13
ST-S5
5-4. PRINTED WIRING BOARD MAIN Board · See page 11 for Circuit Boards Location.
· Semiconductor Location
Ref. No. D551 D552 D901 D902 D903 D904 D911 D912 D913 D920 D921 D922 D923 D941 D942 D943 D944 D945 IC501 IC551 IC901 IC903 IC904 IC951 IC952 IC991 Q502 Q503 Q551 Q901 Q902 Location D-4 D-4 C-8 C-7 E-4 E-5 C-6 C-5 C-5 F-4 E-5 D-5 D-5 C-7 C-7 E-4 E-3 E-4 C-2 D-4 E-6 D-6 G-4 G-10 F-10 H-8 E-3 E-4 D-4 C-5 F-4
1
2
3
4
5
6
7
8
ANTENNA
9
10
(E, AUS)
A
SYSTEM CONTROL 1 (TO TA-S7AV)
(AEP, UK)
COAXIAL FM 75
FM 75
AM
FM/AM TUNER UNIT *
MAIN BOARD
R524
* SUPPLIED WITH THE ASSEMBLED BLOCK
(CHASSIS)
R523 EPT901
JW108
JW971
C561 R531 R556 R542 R541 R530 C943 R533 R534 R526 R532 R528 R515 C562 R522
10
(FOR TEST) 1
JW921
B
R527
EPT902 R958 CN5042
(AEP, UK)
(CHASSIS)
JW34
JW104
JW53
JW47
R957
C961
(AEP, UK)
R956
1
CN503 CN5032 R525 Q901 C909
C B 1
R959 D902 C941 CN506 R962
JW41
JW40
JW42
JW91
JW90
R513
JW50
JW51
E
JW116 D911 C972 C927 R943 D941 D942 JW959
4
JW89
SYSTEM CONTROL 2
JW98
(TO TA-S7AV)
R529
R961 R942
9
JW43
C
R535 R536 R537 R538 R511 R539 R540 JW32 C504
R903 R906 D913 R908
IC501
R516
R514
(E, AUS)
R512 JW502 JW501 JW39 R517
1
R964
R963
JW500
C505
JW38
4 CN501 (FOR TEST) C552 D551 1
R519 R520 C520 R905 R904 C910 D912 C915
JW25
C928
JW958 CN5031
R941 C953
R966
JW44
R518
JW118
JW92
C962
CN5041
C519
C937
1
JW88 JW107 D901
1
JW87 R965
15
5
1
D
R543 R545 C509 R544 R546 (E, AUS) JW21 C508 X501
X502 R510 R509 C502 R508 C503 JW30 JW29 C501 JW503 JW96 C510 JW27 JW26 JW113 R558 R506 R557
R521
E
3
IC551
D552
R551 C551
R552 C553
JW115
D923 D922
10
Q551 R553
JW84
3 1
R554 R555
JW55 C942
E
D903
JW119
IC903
D921
JW94 JW106 JW100 JW80 JW81
SYSTEM CONTROL 3
JW19
R548 R502 R504
D944 E
D945
JW920
E
JW17 JW18 JW35
D904
JW83
D943 C506 R549 R550 Q502 Q503
C905
C904
CN505
FROM CDP-S3
1
JW37
D
PANEL BOARD CN602
JW13
3 3 1
C952
JW78 JW76
JW79 JW77
R501
R503
R505
R507 JW28
C918
C903
JW952
NO901
IC901
JW65 JW56
JW917 JW70 CLP101 JW68 JW71 C902
JW16 CN502 JW15 JW14 R912
E
F
JW209 JW208 JW207 JW206 JW205 JW204 JW203 C970 CN509 JW93
Q902
R911 D920
JW97
JW69
(Page 18)
IC952
C957
JW918
JW67
3
JW86
IC952 OPTICAL IN
JW62
3
1
JW117 JW85 C978
C956 C916
1
IC904
JW99
JW60 R952
IC951
3
IC951 OPTICAL IN (FROM CDP-S3)
JW957
JW954
JW956
G
JW112
JW202 JW201
CN508
JW64 C977 JW110 C964
L951 C955
C968 C971
C907
C906 L955 C966 JW75
1
JW111 CN510
5 1
NO507
1 4
R951
1-680-695DSP BOARD CN601
11 (11)
C
DSP BOARD CN602
B
DSP BOARD CN603
C992
(Page 15)
(Page 15)
3 1
IC991
3 SYSTEM CONTROL 4 (TO TC-S3) 1
A
(Page 15)
H
NO991 C991
(INCLUDED IN MAIN BOARD)
14
14
ST-S5
5-5. PRINTED WIRING BOARD DSP Board · See page 11 for Circuit Boards Location.
1
2
3
4
5
6
7
8
J601 MD
9
VIDEO (AUDIO) IN
R L R
· Semiconductor Location
Ref. No. D601 D604 D605 D607 D608 D609 D610 IC601 IC602 IC603 IC604 IC605 IC606 IC607 IC608 IC609 IC610 Q601 Q602 Q603 Q604 Q605 Q606 Q607 Q608 Q609 Q610 Q611 Q612 Q613 Location C-8 D-7 D-7 E-2 E-2 E-1 E-1 C-4 C-6 E-4 C-2 D-3 E-7 F-2 C-2 B-6 C-7 C-8 F-6 F-7 E-9 D-9 G-8 G-9 E-8 F-8 F-8 C-9 E-6 D-8
A
DSP BOARD DSP BOARD (COMPONENT SIDE)
(CONDUCTOR SIDE)
IC609 OPTICAL OUT
J602 SUB WOOFER OUT
OUT L R L
IN
(CHASSIS) EP604
3
1
C719 C717
EP603 (CHASSIS)
IC609
R734 C720 C634 C712 C711
B
R743 R746 R739 R781 R756 R757
C732 R742 R738 R735 R779 R780 C631 C630 C611
C735 C714 R750
FB603
C713 R749 C633
C715 R752
C716 R751 C709
R748 R747 C659
IC610
3
E
C665
IC608
R668 R669 C632 R678 C627
36 37 25 24
C610 C629 R667 C626 R692 C625 X601 C612 C740 1 C601 C603 C604 R602
JR622
120
91 90
C661
D601
FB601
C660
1 C664 Q601
C710 C666 C706 R682 E Q611 R733 R731 C622 R677 R674 R675 R676 C704 C695 R701
R703
C
R670 R671 R672 C628 R673
IC601
FB602 C609 C614 C608
30 31 60 61
C739 C662 R623 R601 R688 C623 C621 R683 C620 C694 C730 Q613 C741 D604 R629 R664 R628 C615 R656 R630 R665 C656 C645 C655 C637 C636 C639 C658 C635 C731 JR621 C641 C685 C693 C638 C640 R721 C684
E
C705 C707
IC604
48 1 12 13
R690 C602 R689
R691 R687 R684 R686 R685
R634
C624
R603 R604 R605 R606
C613
R730
C617 C618 R681
C708
R640
R637
R639
R611 R612 R613 R636 R635
C646
C606
C607
R618
IC602
C738 R621 R620 R619 D605 R610
R607 R608
R679 C619
R616 R617
D
R641
R638
1
C742
11
R771 E R699
R614
12
44
C736
R615
R654
R696 C692 R702
R698
E Q605
JR620
IC605
22 34
R647
R653 C644 C657
D610 D608 R643
R644 R645
R706 R758 R760 R762 R707
23
33
R648
IC603
R666 R657
R697 R700
R646 D609 D607
(E, AUS)
C642 C643 R642
C686 C687
C724
E
R772
FB608
Q612 E
C647 C651 C702 R725
E
R720 R719 R729
C722
E
R765 R769
R658 R660 R631 C653 C654 R633 R661 C701 C683 R632 R655 R680 C650 C652 R662 R659 C616
IC606
Q604 C726
Q608 C723
C725
C727 C728
FB607
R768
E Q609
C729 R784
IC607
C682 C649 R663 R754 Q602
R775
FB604 C648
C703 R727
R723 E R728
R724
F
R713 R717
C681 C721 JR603 JR601
B
R709 C699 D606
E
FB605 C680 C679
1
Q610 C689 C691 R649
4
E
MAIN BOARD CN508
(Page 14)
CN603
E
A
C676 R715 C677 R716 R711 R712 R759 C675
MAIN BOARD NO507
R650 C690 Q603
R777 R776
CN601
R755 C673 C674
C678 R651 R652 FB606
(Page 14)
Q606
C700
Q607 R778 (E, AUS)
C672
C671
C670
C669 R693 R695 R694
R770 R773 R766 R763 R767
(CHASSIS)
EP602
G
R761
CN602
11 1-680-319(11)
R774 C668 C667 C733
1-680-319-
11 (11)
C
MAIN BOARD CN509
(Page 14)
15
15
ST-S5
5-6. SCHEMATIC DIAGRAM DSP Board (1/2) · See page 20 for Waveforms. · See page 20 for IC Block Diagram.
1 2 3
R665 100 E1
E2
C657 1000p
4 C656 220 10V
R666 100
R664 100
C655 0.1
CN602 21P A+5V A-GND D+5V D-GND DIR-UNLOCK DIG-CLK DIR-CS DSP-Rx DIR-XSTATE DIG-Tx DIR-Rx AMP-LAT CODEC-SMUTE B1 C616 220 10V C2 B3 C615 0.1 FB604 0 C648 220 10V C3 C5 C4 E2 C2 R633 100 R628 100 C5 R632 100 R629 100 C6 E1 C1 R631 100 Q612 FN1F4M MUTING LEVEL SHIFT R630 100 CONTROL SWITCH C4 F3 C6 F2 C3 F1 R655 10k H3 H7 H2 TP619 D4 R656 10k R657 100 R658 100 R659 100 6 IC603 TC74HCT7007AF FB605 0 R662 100 Q602 2SC1623 R660 330 JR603 0 C653 0.1 C654 0.01 FB607 FB608 R680 3.3k DIGITAL FILTER, D/A CONVERTER IC606 PCM1748E/2K JR621 0 5
(Page 12)
AMP-CLK DSP-ACK AMP-DATA DSP-CS DSP-DECODE D-GND D-OUT
B2
C651 0.1
E1
E2
+3.3V REGULATOR R663 470 C649 0.1 C650 220 10V
C1
R661 330 7 C652 0.1
R617 100
R616 100
R615 100
R614 100
D-GND
R619 100
N1
N2
N3
N4
N5
N6
N7
N8
R618 100 R620 100 C738 0.001 C607 0.1
C647 220 10V
A2
A1
C606 0.1
R649 470 R652 470 R651 470 R650 470
N10
N9
8
TP621 PAGE0
TP623 PAGE1
R648 330
R647 330
R646 330
R645 330
R644 330
R643 330
C641 0.01
C640 0.01
C639 0.01
C638 0.01
C637 0.01
C642 0.001
D604 1SS355 C643 0.001 R613 100 R612 100 R611 100 A3 A4 A5 R621 100 R610 100 R608 100 R607 100 R606 100 G6 C608 0.1 CN601 4P A6 D0 A7 A8 D1 R754 100 A9 AUDIO DIGITAL SIGNAL PROCESSOR A10 A11 C721 220 10V A12 A13 C609 0.1 A14 A15 A16 A17 S-RAM TP601 TDO TP602 MS TP622 PLOCK C601 0.1 C602 0.01 C603 0.1 G5 IC601 CXD9617R R602 1k C604 0.1 R605 100 R604 100 JR622 0 G4 G2 G3 C658 0.1 D605 1SS355
C636 0.01
H7 H6 H5 H4 G1
(Page 17)
C645 220 10V C644 0.1
H3 H2 H1
R653 10k A/D,D/A CONVERTER IC605 AK4527
R642 100 9 C635 0.1
R755 100
R603 100 C646 0.01 R654 10k
(Page 12)
C736 0.1
A13
A11
A12
A10
A19
A18
A17
A16
A15
A14
A8
A9
A5
A3
A4
A2
A6
A7
A1
R636 100
TP604 TCK TP605 TDI C740 0.1 R601 100 TP614 BCK TP615 LRCK TP618 D2 TP617 D3 TP611 Q613 FA1A4M RESET SWITCH R634 100 BCK
IC602 IS61LV6416-15T
R637 100
R638 100
R639 100
R640 100
C613 0.1
TP603 XTRST
R623 10k
R635 100
R641 100
TP616 DOUT
H2
H3
H4
H5
H6
H1
10 11 12 13
C612 0.1
C739 0.001
C742 0.001
R771 10k 14
C610 0.1 C614 0.1
C611 0.1 C659 220 10V +2.6V REGULATOR G O IC610 NJM2391DL1-26TE1 I 16 17 18 19 15
A23
A22
A21
A24
A20
EP604 C735 GND 0.1 (CHASSIS)
A34
A33
A32
A31
A30
A29
A28
A27
A26
A25
A18
A19
A20
A21
A22
A23
A24
A25
A26
A27
A28
A29
A30
16
A31
A32
A33
A34
FB601 0
16
ST-S5
5-7. SCHEMATIC DIAGRAM DSP Board (2/2) · See page 20 for Waveforms. · See page 20 for IC Block Diagram.
1 2 3 Q603
K6 K9 K7 K8 K2 K3 K1 J1 R766 1k R765 1k R763 1k J3
+5V REGULATOR
Q603 2SC1623
4 C690 220 10V
(E,AUS) R778 1k C691 0.1
R776 10k
J2 J4
R777 10k
R768 10k
R775 10k
R774 1k
R773 1k
R772 1k
R770 1k
R769 1k
R767 1k
R762 1k
FB606 47 C689 100 16V
INPUT SELECT SWITCH, GRAPHIC EQUALIZER CONTROL, ELECTRICAL VOLUME 5 IC607 M61512FP
R761 1k JR601 0 R760 1k C667 C668 6 N1 N2 N3 N4 7 N5 N6 N7 N8 N9 N10 C669 C670 C671 C672 C673 C674 10 50V 10 50V 10 50V 10 50V 10 50V 10 50V C687 100 16V C686 100 16V C722 0.1 C723 10 50V C724 0.1 C725 C726 10 0.1 50V C727 10 50V
C728 0.1 10 50V
K4 J5 K5 J6
10 50V 10 50V
R759 1k R758 1k
C729
C733 0.1
EP602 GND CN603 23P
C675 1 50V C676 1 50V C677 1 50V C678 10 50V R693 100 R694 100 R695 100 R699 470k C685 10 50V
R697 1.8k C692 0.1 C699 R711 10 1k 50V Q606 R713 2SC3624 1k MUTING
I2 K1 K2 K3 K4
(CHASSIS)
TUNER L-IN VCD L-IN TC L-IN TC REC L-OUT A-GND
B3 8 B2 B1
R698 470k
C693 0.1 R702 1M R703 1M R700 10k
R712 47k
K5 Q604 2SC1623 R707 47k K6 K7 R709 D606 0 0 K8 I6 K9 Q604,605 DBFB CONTROL/ I1 I1
R717 1k
TC REC R-OUT TC R-IN VCD R5-IN TUNER R-IN A+10V MIC-IN A-GND TP606 FL FL-OUT F-GND I2 TP607 FR FR-OUT A-GND I3 TP608 SL LS-OUT S-GND I4 TP609 SR RS-OUT C-GND I5 TP610 C C-OUT LINE-MUTE
C684 10 50V
R701 10k
C694 0.1
R706 47k Q605 2SC1623
C741 0.1
C695 0.1
R696 1.8k C700 10 50V
FEED BACK SWITCH
FB602 0
C618 0.01
C679 0.1
R715 1k
(Page 12)
D607 RB501V
D608 RB501V
(Page 16)
FB603 Q601 2SD1387 +3.3V REGULATOR 9 C623 220 10V R692 100 C665 0.1 C666 220 10V
Q607 2SC3624 R677 5.6k D609 RB501V R679 4.7k
M1 M3 M2
R716 47k D610 RB501V C730 10 50V L4 C701 1 50V R719 1k C731 0.1
MUTING
(E,AUS) C680 10 50V L1 C681 1 50V L2 C682 1 50V L3 C683 1 50V L4 I4
R676 100
C619 0.1 R681 33k C621 0.01
R683 100
R721 1k Q608 2SC3624
I6 JR620 0
DBFB FEEDBACK
R682 100
R675 100
R720 47k R674 100 L3 C702 1 50V R723 1k
MUTING I3 R725 1k Q609 2SC3624 J1 C710 10 50V R752 47k C716 220p C715 220p C709 10 50V R751 47k R742 15k C708 10 50V R750 12k C714 220p R739 15k C707 10 50V R749 12k C713 220p R738 1k C706 10 50V R748 100k C712 470p R735 1k C711 470p C705 10 50V R746 10k R743 10k
TP624 A.GND
C620 0.1 C622 0.1
C660 220 10V C661 220 10V
C662 0.1
C664 0.1 D601 RD3.9SB2
C617 0.1 L2 C703 1 50V
J601 6P L
R724 47k
MUTING I5 J2
VIDEO (AUDIO)
R727 1k Q610 2SC3624
R729 1k J3
R
IN
TP620 BCK
TP613 DATA
TP612 LRCK
L IN R MD L OUT R
G1 G2 G3 G4
R684 100 R685 100 R686 100 R687 100 R688 100 C624 0.1 L1 R673 100
C704 2.2 50V
R728 47k
MUTING
J4 R731 4.7k Q611 2SC3624 MUTING R733 1k
R730 22k DIGITAL AUDIO INTERFACE RECEIVER IC604 LC89056W-E R672 100 INVERTER IC608 SN74LVU04APWR M1 R756 47k R757 47k R781 47k
J5
G5
R689 1k
J6 R780 47k R779 47k C631 0.01
R747 100k R734 1k
J602 1P SUB WOOFER OUT
G6
R667 100
R690 1M
E1
M2
D1 C720 220p D0 C717 0.1 C719 0.1 C718 NO MT EP603 GND
10 11 12 13
R691 0
R671 100
M3
C630 0.01
X601 13.5MHz R678 10k C625 10p C626 10p C628 0.1 C629 0.1 C627 0.1
F1
(CHASSIS) C732 0.1 OPTICAL TRANSCEIVER IC609 TOTX178A C632 0.1 C633 220 10V C634 0.1 D.GND OPTICAL VCC OUT
14
R668 100
R669 100
R670 100
15 16 17 18 19
E2
F3
D.OUT F2
17
17
ST-S5
5-8.
PRINTED WIRING BOARDS PANEL Section
· See page 20 for Circuit Boards Location.
1
PANEL BOARD
2
3
4
5
6
7
8
9
10
A
C610 JW24
R603 JW11 C649 S611 C650 JW1
STEREO/MONO
C601 C651 C664 C653 C655 C657 C659 C661
FL601 FLUORESCENT INDICATOR TUBE S601
B
R623 R624 R625
C665
C666 R601 R602 R638 R636 R639 R637 R635 R633 R631 R629 R605 C614
R626
C652 C663 R616
C654
C656
C658
C660
C662
JW31 JW33 JW36
S607
ENTER
S608
S609
PRESET +
S610
TUNER MEMORY
R634 R632 R630 R628
JW57
IC601
DISPLAY
SIRCS BOARD
C101 S602
CLOCK/TIMER
C603
R622
R621
R620
C
S606
D601
C607
C608 JW601
JW114 JW3 3 R618 C605 JW4 S603
TIMER SELECT
IC101
1 R102 C606
JW602
S605
TUNING +
S604
TUNER/BAND
JW8 JW10
R604
C615
R677
JW5 R617
X601 R607
R627 R619 C669 R606 R608 JW45 S601 612
MAIN BOARD CN502
JW6
(AEP, UK) (AEP, UK)
CN602
NO601
1 3
NO101 1 3 R101
S612
D
PTY
D
1-680-69611 (11)
1-680-69711 (11)
(Page 14)
· Semiconductor Location
Ref. No. D601 IC101 IC601 Location C-5 C-10 B-5
18
18
ST-S5
5-9.
SCHEMATIC DIAGRAM PANEL Section
· See page 20 for Waveform.
FL601 FLUORESCENT INDICATOR TUBE
100
47
46
45
44
43
41
40
39
38
37
36
35
34
33
32
31
30
29
C610 10 50V
100p 100p 100p 100p 100p 100p 100p 100p 100p 100p 100p C661 100p C662
12
30
29
28
27
26
25
24
22
21
20
19
18
17
16
15
14
13
10
9
8
7
6
5
4
3
2
1
C651
C652
C653
C654
C655
C656
C657
C658
C659
(AEP,UK) S612 PTY R627 5.6k
VDD FOR VFT A22 A21 A20 A19 A18 A17 A16 A15 A14 A13 A12 A11 A10 A9 A8 A7 VSS FOR IO A6 A5 G1 G2 G3 G4 G5 G6 A4 A3 A2 A1
R616 100k CN602 19P DISP/STANDBY KEY VF VF G7 100 G7 99 G8 98 A26 G9 97 A27 36 A28 37 A29 G12 B6 A30 39 A31 40 A32 41 A33 VSS FOR IO 43 A34 G12 B7 IIC-DATA DISPLAY CONTROLLER IC601 MB90M407PF-G-102 -BND B8 IIC-CLK B9 KEY1 D+3.3V D-GND C669 0.1 EVER+5V(SIRCS) SIRCS RESET G12 VOLB 38 G11 101 B5 VOLA G10 96 B4 JOG1-A B3 JOG1-B B2 JOG2-A B1 JOG2-B D-GND -VP
31 A23 S611 STEREO/ MONO 34 S610 TUNER MEMORY R626 3.9k 35 32 A24 33 A25
S609 + PRESET
R625 2.7k
C660
101
10
12
13
14
28
27
26
25
24
22
21
20
19
18
17
16
15
6
5
99
4
98
9
3
97
8
2
96
7
1
(Page 13)
S608 -
R624 2.2k
S607 ENTER
R623 1.5k
44 A35 45 A36 A37
D601 1SS133T-72
46 S606 TP601
C649 10000p
R622 1.2k
A38 VKK FOR VFT MODE0
MODE2 JOG2B JOG2A JOG1B JOG1A I2C CLK
AVSS FOR ANALOG
AVCC FOR ANALOG
47
VCC FOR CPU XOUT XIN VSS FOR CPU
RESET
X601 4MHz
S605 +
R621 1k
R601 10k
MODE1
I2C DATA
TUNING
TP602
VOLA VOLB
KEY0
S604 TUNER/BAND
R620 820 C663 10000p
R602 10k
KEY1
C608 0.1
R677 1k
S601 DISPLAY R603 10k
TP603
S603 TIMER SELECT
R619 560
C664 0.1
NO601 3P GND +5V
NO101 3P GND +5V OUT R101 47
C101 47 16V
IC101 GP1U28X
C601 10000p
TP604
TP606
C650 10000p
TP608 OUT
TP607 TP605
S602 CLOCK/TIMER
R618 470
C615 220p
C614 220p
R102 47
REMOTE CONTROL RECEIVER
R639 1k
R637 1k
R635 1k
R633 1k
R631 1k
C665 47 50V
R629 1k
B7 R604 100
B8 R605 100
C666 47 50V
B1
B2
B3
B4
B5
B6
B9
R638 10k
R636 10k
R634 10k
R632 10k
R630 10k
R628 10k
R617 270
R606 10k
R607 10k
R608 10k C607 100 6.3V C606 10 50V
C667 0.1
C668 0.1
C605 10000p
C603 0.1
19
19
ST-S5
· Waveforms MAIN Board
1 IC501 qa (XCOUT)
DSP Board
1 IC601 9 (MCLK1), IC604 w; (XMCK), wa (XOUT) 5 IC601 ws (KFSIO), IC604 qd (CKOUT)
· IC Block Diagrams DSP Board IC604 LC89056W-E
DI DO ERROR BPSYNC ERR9P DGND VF F2 F1 F0 CSFLAG XSEL
36 35 34 33 32 31
30
29 28 27 26 25
2.6 Vp-p
4 Vp-p
4.4 Vp-p
CE 37 CL 38 XSEL 39 MODE0 40 MICROCOMPUTER INTERFACE SAMPLING FREQUENCY 22 21 20 19 18 17 16 15 14 13 XIN XOUT XMCK DVDD DGND XSTATE DATAO LRCK BCK CKOUT C BIT DETECT PA/PB DETECT 24 AUDIO 23 EMPHA
30.5 µs
88.6 ns 74.1 ns
MODE1 41 DGND 42 DVDD 43
LOCK DETECT
X' TAL
2 IC501 qd (XOUT)
2 IC601 qf (SCKOUT)
6 IC601 wk (LRCKI2), IC604 qg (LRCK)
DOSEL0 44 DOSEL1 45 CKSEL0 46 CKSEL1 47 DATA DEMODULATOR TIMING
2.7 Vp-p
4.6 Vp-p
3.9 Vp-p
XMODE 48
INPUT CIRCUIT
PLL
1
DISEL
2 3
DOUT DINO
4
DINI
5
DIN2
6 7
DGND DVDD
8 9 10
R VIN LPF
11 12
AVDD AGND
62.5 ns
74.1 ns
22.7 µs 7 IC601 wl (BCKI2), IC604 qf (BCK)
3 IC601 ql (LRCKO), IC605 5 (LRCK), IC606 3 (LRCK (I))
IC605
4 Vp-p
3.8 Vp-p
AK4527
LOOP1 LOOP0/SDA/CDTI DIF1/SCL/CCLK DIF0/CSN P/SN MCLK DZF1 AVSS AVDD VREFH VCOM
44 43 42 41 40 39 38 37 36 35 34
354 ns
PANEL Board
1 IC601 id (XOUT)
22.7 µs 4 IC601 w; (BCKO), IC605 4 (BCK), IC606 1 (BCK (I)) 8 IC606 qh (MCLK (I))
SDOS I2C SMUTE BICK LRCK SDTI1 SDTI2 SDTI3
1 2 3 4 5 6 7 8
INPUT CIRCUIT
AUDIO INTERFACE
OUTPUT CIRCUIT
33 32 31 30 29 28 27 26 25 24 23
DZF2 RIN+ RIN LIN+ LIN ROUT1 LOUT1 ROUT2 LOUT2 ROUT3 LOUT3
3.5 Vp-p
3.7 Vp-p
SDTO 9 DAUX 10 DFS 11 FORMAT CONVERTER 12 13 14 15 16 17 18 19 20 21 22
DEM1 DEM0 TVDD DVDD DVSS PDN ICKS2 ICKS1 ICKS0 CAD1 CAD0
3.6 Vp-p
250 ns
74.1 ns
354 ns
20
20
ST-S5
5-10.
IC PIN FUNCTION DESCRIPTION
Pin Name AMP-DATA AMP-CLK AMP-LAT SIRCS DIG-TX DSP-RX DIG-CLK GND CNVSS XCIN XCOUT RESET XOUT VSS XIN VCC NMI RDS-INT -- RDS-DATA ST-MUTE ST-CE ST-DOUT -- ST-DIN -- ST-CLK -- IIC CLK IIC DATA NO-USE -- M-RESET -- NO-USE -- EXP-IN DATA EXP-OUT DATA EXP-LAT EXP-CLK VCC SOFT-TEST I/O O O O I O I O -- -- I O I O -- I -- I I -- I O O O -- I -- O -- I/O I/O -- -- O -- -- -- I O O O -- I Description Serial data output to the M61512FP (IC607) Serial data transfer clock signal output to the M61512FP (IC607) Serial data latch pulse signal output to the M61512FP (IC607) Remote control signal input from the remote control receiver (IC101) Serial data output to the CXD9617R (IC601), digital audio interface receiver (IC604) and digital filter (IC606) Serial data input from the digital audio interface receiver (IC604) Serial data transfer clock signal output to the CXD9617R (IC601), digital audio interface receiver (IC604) and digital filter (IC606) Ground terminal Not used Sub system clock input terminal (32.768 kHz) Sub system clock output terminal (32.768 kHz) System reset signal input from the reset signal generator (IC551) "L": reset For several hundreds msec. after the power supply rises, "L" is input, then it changes to "H" Main system clock output terminal (16 MHz) Ground terminal Main system clock input terminal (16 MHz) Power supply terminal (+5V) Non-maskable interrupt input terminal Fixed at "H" in this set Serial data transfer clock signal from the RDS decoder on the FM/AM tuner unit Not used (open) Serial data input from the RDS decoder on the FM/AM tuner unit Tuner muting on/off control signal output to the FM/AM tuner unit "L": muting on Chip enable signal output to the FM/AM tuner unit Serial data output to the FM/AM tuner unit Not used (open) Serial data input from the FM/AM tuner unit Not used (open) Serial data transfer clock signal output to the FM/AM tuner unit Not used (open) Communication data reading clock signal input or transfer clock signal output with the display controller (IC601) and CDP-S3 Communication data bus with the display controller (IC601) and CDP-S3 Not used Not used (open) Reset signal output to the display controller (IC601) "L": reset Not used (open) Not used Not used (open) Serial data input from the I/O expander in the TA-S7AV Serial data output to the I/O expander in the TA-S7AV Serial data latch pulse signal output to the I/O expander in the TA-S7AV Serial data transfer clock signal output to the I/O expander in the TA-S7AV Power supply terminal (+5V) Soft test output terminal Not used (open)
· MAIN BOARD IC501 M30622MGA-A39FP (SYSTEM CONTROLLER) Pin No. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 to 34 35 to 40 41 42 to 50 51 52 to 57 58 59 60 61 62 63
21
ST-S5
Pin No. 64 65 to 70 71 72 73 74 75 76 77 78 79 80 81 82 83 to 86 87 88 89 to 91 92 93 94 95 96 97 98 99 100
Pin Name VSS -- LINE-MUTE -- DISPLAY KEY POWER KEY DIR-UNLOCK DIR-CS DIR-XSTATE DIR-RX CODEC-SMUTE DSP-ACK DSP-CS DSP-DECODE -- STEREO TUNED -- MODEL-IN SPEC-IN -- V-MUTE AVSS -- VREF AVCC AC-CUT
I/O -- -- O -- I I I O I I O I O O -- I I -- I I -- O -- -- I -- I Ground terminal Not used (open)
Description
Audio line muting on/off control signal output to the audio line circuit "L": muting on Not used (open) DISPLAY switch (S601) input terminal Power on/off switch in the TA-S7AV input terminal PLL lock error and data error flag input from the digital audio interface receiver (IC604) Chip enable signal output to the digital audio interface receiver (IC604) Source clock switching monitor input from the digital audio interface receiver (IC604) Read data input from the digital audio interface receiver (IC604) Soft muting on/off control signal output to the A/D, D/A converter (IC605) "L": muting on Acknowledge signal input from the CXD9617R (IC601) Chip select signal output to the CXD9617R (IC601) Decode signal input from the CXD9617R (IC601) Not used (open) FM stereo detection signal input from the FM/AM tuner unit "L": stereo Tuning detection signal input from the FM/AM tuner unit "L": tuned Not used (open) Model setting terminal Specification setting terminal Not used (open) Video muting on/off control signal output terminal "L": muting on Not used (open) Ground terminal Not used (open) Reference voltage (+5V) input terminal Power supply terminal (+5V) AC cut on/off detection signal input from the reset signal generator (IC551) "L": AC cut on, "H": AC cut off or checked
22
ST-S5
· DSP BOARD IC601 CXD9617R (AUDIO DIGITAL SIGNAL PROCESSOR) Pin No. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 to 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 Pin Name VSS XRST EXTIN FS2 VDDI FS1 PLOCK VSS MCLK1 VDDI VSS MCLK2 MS SCKOUT LRCKI1 VDDE BCKI1 SDI1 LRCKO BCKO VSS KFSIO SDO1 to SDO3 SDO4 SPDIF LRCKI2 BCKI2 SDI2 VSS HACN HDIN HCLK HDOUT HCS SDCLK CLKEN RAS VDDI VSS CAS DQM CS0 WE0 VDDE WMD1 I/O -- I I I -- I O -- I -- -- O I O I -- I I O O -- I O O O I I I -- O I I O I O O O -- -- O O O O -- I Ground terminal Reset signal input from the M61512FP (IC607) "L": reset Master clock signal input terminal Power supply terminal (+2.6V) Sampling frequency selection signal input terminal Internal PLL lock signal output terminal Ground terminal Oscillation clock signal input from the digital audio interface receiver (IC604) Power supply terminal (+2.6V) Ground terminal Oscillation clock signal output terminal Not used (open) Master/slave selection signal input terminal "L": slave, "H": master (fixed at "L" in this set) Internal system clock signal output to the digital filter (IC606) L/R sampling clock signal (44.1 kHz) input terminal Power supply terminal (+3.3V) Bit clock signal (2.8224 MHz) input terminal Not used (open) Audio serial data input from the D/A, A/D converter (IC605) L/R sampling clock signal (44.1 kHz) output to the D/A, A/D converter (IC605) and digital filter (IC606) Bit clock signal (2.8224 MHz) output to the D/A, A/D converter (IC605) and digital filter (IC606) Ground terminal Audio clock signal input from the digital audio interface receiver (IC604) Audio serial data output to the A/D, D/A converter (IC604) Audio serial data output to the digital filter (IC606) S/PIDF signal output terminal Not used (open) L/R sampling clock signal (44.1 kHz) input from the digital audio interface receiver (IC604) Bit clock signal (2.8224 MHz) input from the digital audio interface receiver (IC604) Audio serial data input from the digital audio interface receiver (IC604) Ground terminal Acknowledge signal output to the system controller (IC501) Write data input from the system controller (IC501) Clock signal input from the system controller (IC501) Read data output to the system controller (IC501) Chip select signal input from the system controller (IC501) Clock signal output terminal Not used (open) Not used (open) Not used (open) Clock enable signal output terminal Power supply terminal (+2.6V) Ground terminal Column address strobe signal output terminal Output terminal of data input/output mask Not used (open) Not used (open) Not used (open) Not used (fixed at "L") Not used (open) Not used (fixed at "L") Not used (fixed at "L") Sampling frequency selection signal input terminal Description
Row address strobe signal input terminal
Chip select signal output to the S-RAM (IC602) Write enable signal output to the S-RAM (IC602) Power supply terminal (+3.3V) S-RAM wait mode setting terminal Fixed at "H" in this set
23
ST-S5
Pin No. 48 49 50 51 52, 53 54 55 56 57 58 59 60 61 62, 63 64 to 66 67 68 69 70 71 72 to 75 76 77 to 80 81 82 to 85 86 87 88 89 90 91 92 to 97 98, 99 100 101 102 to 105 106 107, 108 109, 110 111 112 113 114, 115 116 117 to 119 120
Pin Name VSS WMD0 PAGE2 VSS PAGE1, PAGE0 BOOT BTACT BST MOD1 MOD0 EXLOCK VDDI VSS A17, A16 A15 to A13 GP10 DECODE AUDIO VDDI VSS D15 to D12 VDDE D11 to D8 VSS A9, A12 to A10 TDO TMS XTRST TCK TDI VSS A8 to A3 D7, D6 VDDI VSS D5 to D2 VDDE D1, D0 A2, A1 VSS A0 PM SDI3, SDI4 SYNC VSS VDDI
I/O -- I O -- O I I I I I I -- -- O O O O I -- -- I/O -- I/O -- O O I I I I -- O I/O -- -- I/O -- I/O O -- O I I I -- -- Ground terminal
Description S-RAM wait mode setting terminal Fixed at "L" in this set Page selection signal output terminal Not used (open) Ground terminal Page selection signal output terminal Not used (open) Boot mode control signal output terminal Not used (fixed at "L") Boot mode state display signal output terminal Not used (open) Boot trap signal input from the M61512FP (IC607) PLL input frequency select terminal Mode setting terminal "L": 384fs, "H": 256fs (fixed at "H" in this set) "L": single chip mode, "H": use prohibition (fixed at "L" in this set)
PLL lock error and data error flag input from the digital audio interface receiver (IC604) Power supply terminal (+2.6V) Ground terminal Address signal output terminal Not used (open) Address signal output to the S-RAM (IC602) L/R sampling clock signal (44.1 kHz) output to the D/A, A/D converter (IC605) and digital filter (IC606) Decode signal output to the system controller (IC501) Bit 1 input terminal of channel status from the digital audio interface receiver (IC604) Power supply terminal (+2.6V) Ground terminal Two-way data bus with the S-RAM (IC602) Power supply terminal (+3.3V) Two-way data bus with the S-RAM (IC602) Ground terminal Address signal output to the S-RAM (IC602) Simple emulation data output terminal Not used (open) Simple emulation data input start/end detection signal input terminal Not used (open) Simple emulation asychronous break input terminal Not used (open) Simple emulation clock signal input terminal Not used (open) Simple emulation data input terminal Not used (open) Ground terminal Address signal output to the S-RAM (IC602) Two-way data bus with the S-RAM (IC602) Power supply terminal (+2.6V) Ground terminal Two-way data bus with the S-RAM (IC602) Power supply terminal (+3.3V) Two-way data bus with the S-RAM (IC602) Address signal output to the S-RAM (IC602) Ground terminal Address signal output to the S-RAM (IC602) PLL reset signal input from the M61512FP (IC607) "L": reset Audio serial data input terminal Not used (fixed at "L") Synchronous/asychronous selection signal input terminal "L": Synchronous, "H": asynchronous (fixed at "H" in this set) Ground terminal Power supply terminal (+2.6V)
24
ST-S5
· DSP BOARD IC604 LC89056W-E (DIGITAL AUDIO INTERFACE RECEIVER) Pin No. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 to 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 Pin Name DISEL DOUT DIN0 DIN1 DIN2 DGND DVDD R VIN LPF AVDD AGND CKOUT BCK LRCK DATAO XSTATE DGND DVDD XMCK XOUT XIN EMPHA AUDIO CSFLAG F0 to F2 VF DVDD DGND ERR9P BPSYNC ERROR DO DI CE CL XSEL MODE0 MODE1 DGND DVDD DOSEL0 DOSEL1 CKSEL0 CKSEL1 XMODE I/O I O I I I -- -- I I O -- -- O O O O O -- -- O O I O O O O O -- -- O O O O I I I I I I -- -- I I I I I Description Selection terminal of data input terminal Fixed at "L" in this set Digital data output to the optical transceiver (IC609) Digital data input from the optical receiver (IC952) (for CDP-S3) Digital data input from the optical receiver (IC951) (for external input) Digital data input terminal Not used (fixed at "L") Ground terminal (digital system) Power supply terminal (+3.3V) (digital system) VCO gain control input terminal VCO free run frequency setting input terminal PLL loop filter setting output terminal Power supply terminal (+3.3V) (analog system) Ground terminal (analog system) Audio clock signal output to the CXD9617R (IC601) Bit clock signal (2.8224 MHz) output to the CXD9617R (IC601) L/R sampling clock signal (44.1 kHz) output to the CXD9617R (IC601) Audio serial data output to the CXD9617R (IC601) Source clock switching monitor output to the system controller (IC501) Ground terminal (digital system) Power supply terminal (+3.3V) (digital system) Oscillation clock signal output to the CXD9617R (IC601) System clock output terminal (13.5 MHz) System clock input terminal (13.5 MHz) Emphasis information of channel status output terminal Not used (open) Bit 1 output terminal of channel status to the CXD9617R (IC601) Top 40 bit renovation flag output terminal of channel status Not used (open) Input frequency calculation result output terminal Not used (open) Validity flag output terminal Not used (open) Power supply terminal (+3.3V) (digital system) Ground terminal (digital system) Nine times continuance data transmission error flag output terminal Not used (open) Non-PCM burst and preamble sync signal output terminal Not used (open) PLL lock error and data error flag output to the system controller (IC501) Read data output to the system controller (IC501) Write data input from the system controller (IC501) Chip enable signal input from the system controller (IC501) Clock signal input from the system controller (IC501) Selection input terminal of vibrator frequency terminal Fixed at "H" in this set Mode setting input terminal Fixed at "H" in this set Mode setting input terminal Fixed at "H" in this set Ground terminal (digital system) Power supply terminal (+3.3V) (digital system) Output data format selection signal input terminal Fixed at "L" in this set Output data format selection signal input terminal Fixed at "L" in this set Output clock selection signal input terminal Fixed at "L" in this set Output clock selection signal input terminal Fixed at "L" in this set System reset signal input from the M61512FP (IC607)
25
ST-S5
· DSP BOARD IC605 AK4527 (A/D, D/A CONVERTER) Pin No. 1 2 3 4 5 6 to 8 9 10 11 12 13 14 15 16 17 21, 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43, 44 Pin Name SDOS I2C SMUTE BICK LRCK SDTI1 to SDIT3 SDTO DAUX DFS DEM1 DEM0 TVDD DVDD DVSS PDN CAD1, CAD0 LOUT3 ROUT3 LOUT2 ROUT2 LOUT1 ROUT1 LIN LIN+ RIN RIN+ DZF2 VCOM VREFH AVDD AVSS DZF1 MCLK P/S DIF0 DIF1 LOOP0, LOOP1 I/O I I I I I I O I I I I -- -- -- I I I O O O O O O I I I I O O I -- -- O I I I I I Description Audio serial data source selection signal input terminal "L": internal ADC output, "H": DAUX input (fixed at "L" in this set) Serial control mode selection signal input terminal "L": 3-wire serial, "H": I2C bus Soft muting on/off signal input from the system controller (IC501) "L": muting on Bit clock signal (2.8224 MHz) input from the CXD9617R (IC601) L/R sampling clock (44.1 kHz) signal input from the CXD9617R (IC601) Audio serial data input from the CXD9617R (IC601) Audio serial data output to the CXD9617R (IC601) Audio serial data input terminal Not used (fixed at "L") Double speed sampling mode signal input terminal "L": normal speed, "H": double speed (fixed at "L" in this set) De-emphasis signal input terminal Fixed at "L" in this set De-emphasis signal input terminal Fixed at "H" in this set Power supply terminal (+5V) (for output buffer ) Power supply terminal (+5V) (digital system) Ground terminal (digital system) Power down and reset signal input from the M61512FP (IC607) "L": power down and reset Input clock signal selection terminal Fixed at "L" in this set Chip address signal input terminal Not used (fixed at "L") Analog signal output for center to the M61512FP (IC607) Analog signal output for sub woofer to the M61512FP (IC607) Analog signal output for surround L-ch to the M61512FP (IC607) Analog signal output for surround R-ch to the M61512FP (IC607) Analog signal output for front L-ch to the M61512FP (IC607) Analog signal output for front R-ch to the M61512FP (IC607) L-ch analog signal negative input from the M61512FP (IC607) L-ch analog signal positive input from the M61512FP (IC607) R-ch analog signal negative input from the M61512FP (IC607) R-ch analog signal positive input from the M61512FP (IC607) Zero input detection terminal Not used (open)
18 to 20 ICKS2 to ICKS0
Common voltage output terminal Large external capacitor is used to reduce power supply noise Reference voltage (+5V) input terminal Power supply terminal (+5V) (analog system) Ground terminal (analog system) Zero input detection terminal Not used (open) Master clock signal input from the CXD9617R (IC601) Parallel/serial selection signal input terminal "L": serial control mode, "H": parallel control mode (fixed at "H" in this set) Audio data interface format terminal Fixed at "L" in this set Audio data interface format terminal Fixed at "H" in this set Loop back mode setting terminal Fixed at "L" in this set
26
ST-S5
· PANEL BOARD IC601 MB90M407PF-G-102-BND (DISPLAY CONTROLLER) Pin No. 1 to 6 7 to 10 11 12 to 22 23 24 to 41 42 43 to 47 48 49 50 51 52 53 54 55 56 57 58, 59 60 61 62 63 Pin Name G6 to G1 A1 to A4 VSS FOR IO A5 to A15 VDD FOR VFT A16 to A33 VSS FOR IO A34 toA38 VKK FOR VFT MODE0 MODE1 MODE2 JOG2B JOG2A JOG1B JOG1A VOLA VOLB -- I2C DATA I2C CLK AVCC FOR ANALOG AVSS FOR ANALOG KEY0 KEY1 -- RESET -- VSS FOR CPU XIN XOUT VCC FOR CPU -- G12 G11 to G8 G7 I/O O O -- O -- O -- O -- -- -- -- I I I I I I -- I/O I/O -- -- Description Grid drive signal output to the fluorescent indicator tube (FL601) Segment drive signal output to the fluorescent indicator tube (FL601) Ground terminal (for I/O) Segment drive signal output to the fluorescent indicator tube (FL601) Power supply terminal (+3.3V) (for VFT) Segment drive signal output to the fluorescent indicator tube (FL601) Ground terminal (for I/O) Segment drive signal output to the fluorescent indicator tube (FL601) Power supply terminal (28V) (for VFT) Chip mode selection terminal Chip mode selection terminal Chip mode selection terminal Not used (fixed at "H") Not used (fixed at "H") Not used (fixed at "L")
Jog dial pulse input from the rotary encoder (for sound) in the TA-S7AV (B phase input) Jog dial pulse input from the rotary encoder (for sound) in the TA-S7AV (A phase input) Jog dial pulse input from the rotary encoder (for function) in the TA-S7AV (B phase input) Jog dial pulse input from the rotary encoder (for function) in the TA-S7AV (A phase input) Jog dial pulse input from the rotary encoder (for volume) in the TA-S7AV (A phase input) Jog dial pulse input from the rotary encoder (for volume) in the TA-S7AV (B phase input) Not used (open) Communication data bus with the system controller (IC501) and CDP-S3 Communication data reading clock signal input or transfer clock signal output with the system controller (IC501) and CDP-S3 Power supply terminal (+3.3V) (for analog) Ground terminal (for analog) Key input terminal (A/D input) CLOCK/TIMER, TIMER SELECT, TUNER/BAND, TUNING +/, ENTER, PRESET +/, TUNER MEMORY, STEREO/MONO, PTY (S602 to S612) keys input PTY (S612) key: Used for the AEP and UK models only Key input terminal for TA-S7AV (A/D input) Not used (open) Reset signal input from the system controller (IC501) "L": reset Not used (open) Ground terminal (for CPU) System clock input terminal (4 MHz) System clock output terminal (4 MHz) Power supply terminal (+3.3V) Not used (open) Grid drive signal output to the fluorescent indicator tube (FL601) Grid drive signal output to the fluorescent indicator tube (FL601) Grid drive signal output to the fluorescent indicator tube (FL601)
64 65 66 to 76 77 78 to 80 81 82 83 84 85 to 91 92 to 94 95 to 98 99, 100
I I -- I -- -- I O -- -- O O O
27
ST-S5 SECTION 6 EXPLODED VIEWS
NOTE: · -XX and -X mean standardized parts, so they may have some difference from the original one. · Color Indication of Appearance Parts Example: KNOB, BALANCE (WHITE) . . . (RED) Parts Color Cabinet's Color · Abbreviation AUS : Australian model KR : Korean model MX : Mexican model · Items marked "*" are not stocked since they are seldom required for routine service. Some delay should be anticipated when ordering these items. · The mechanical parts with no reference number in the exploded views are not supplied.
6-1. COVER, FRONT PANEL SECTION 8
#2
7
1
4
5 6 5 7
AEP, UK
3 5
2
#1
Ref. No. 1 1 2 3 4 5
Part No. X-4953-451-1 X-4953-452-1 1-773-114-11 4-232-351-01 1-680-697-11
Description
Remark
Ref. No. 6 6 7 8 #1 #2
Part No. A-4476-267-A A-4476-269-A 3-363-099-21 4-233-134-31 7-685-646-79
Description
Remark
PANEL ASSY (ST), FRONT (AEP, UK) PANEL ASSY (ST), FRONT (KR, MX, AUS) WIRE (FLAT TYPE) (19 CORE) FILTER (FL) SIRCS BOARD
PANEL BOARD, COMPLETE (AEP, UK) PANEL BOARD, COMPLETE (KR, MX, AUS) SCREW (CASE 3 TP2) COVER SCREW +BVTP 3X8 TYPE2 N-S
4-951-620-01 SCREW (2.6X8), +BVTP
7-685-871-01 SCREW +BVTT 3X6 (S)
28
ST-S5
6-2. CHASSIS SECTION
56 55 54
#1
57
#1 #1 #1
53 63
#1
58 52
not supplied A (Including A) #1 #1
#1
61
59
60
51
not supplied not supplied
62
Ref. No. * 51 52 52 52 53 53 53 54 55 56 57 58
Part No. 4-924-098-01 A-2007-939-A A-4476-193-A A-4476-203-A A-4476-199-A A-4476-646-A A-4726-352-A 1-757-599-11 1-757-600-11 1-757-629-11
Description HOLDER, PC BOARD MAIN BOARD, COMPLETE (MX) MAIN BOARD, COMPLETE (AEP, UK) MAIN BOARD, COMPLETE (KR, AUS) DSP BOARD, COMPLETE (AEP, UK) DSP BOARD, COMPLETE (MX) DSP BOARD, COMPLETE (KR, AUS) WIRE (FLAT TYPE) (21 CORE) WIRE (FLAT TYPE) (23 CORE) CORD (WITH CONNECTOR) 5P
Remark
Ref. No. 59 59 59 59 60 60 61 61 61 62 63 #1
Part No. 4-232-327-01 4-232-327-11 4-232-327-41 4-232-327-91 1-769-940-11 1-773-004-11 1-693-529-11 1-693-531-71 1-693-538-11 4-965-822-01
Description
Remark
PANEL (ST), BACK (AEP, UK) PANEL (ST), BACK (AUS) PANEL (ST), BACK (MX) PANEL (ST), BACK (KR) WIRE (FLAT TYPE) (11 CORE) (KR, MX, AUS) WIRE (FLAT TYPE) (15 CORE) (AEP, UK) TUNER PACK (FM/AM) (AEP, UK) TUNER PACK (FM/AM) (MX, AUS) TUNER PACK (FM/AM) (KR) FOOT
1-757-631-11 CORD (WITH CONNECTOR) 20P 1-757-630-11 CORD (WITH CONNECTOR) 19P
3-970-608-01 SUMITITE (B3), +BV 7-685-646-79 SCREW +BVTP 3X8 TYPE2 N-S
29
ST-S5 DSP
NOTE: · Due to standardization, replacements in the parts list may be different from the parts specified in the diagrams or the components used on the set. · -XX and -X mean standardized parts, so they may have some difference from the original one. · RESISTORS All resistors are in ohms. METAL: Metal-film resistor. METAL OXIDE: Metal oxide-film resistor. F: nonflammable · Abbreviation AUS : Australian model KR : Korean model MX : Mexican model Ref. No. Part No. Description
SECTION 7 ELECTRICAL PARTS LIST
· Items marked "*" are not stocked since they are seldom required for routine service. Some delay should be anticipated when ordering these items. · SEMICONDUCTORS In each case, u: µ, for example: uA. . : µA. . uPA. . : µPA. . uPB. . : µPB. . uPC. . : µPC. . uPD. . : µPD. . · CAPACITORS uF: µF · COILS uH: µH The components identified by mark 0 or dotted line with mark 0 are critical for safety. Replace only with part number specified. When indicating parts by reference number, please include the board.
Remark
Ref. No. C640 C641 C642 C643 C644 C645 C646 C647 C648 C649 C650 C651 C652 C653 C654 C655 C656 C657 C658 C659 C660 C661 C662 C664 C665 C666 C667 C668 C669 C670 C671 C672 C673 C674 C675 C676 C677 C678 C679 C680 C681 C682 C683
Part No.
Description 0.01uF 0.01uF 0.001uF 0.001uF 0.1uF 220uF 0.01uF 220uF 220uF 0.1uF 220uF 0.1uF 0.1uF 0.01uF 0.01uF 0.1uF 220uF 0.001uF 0.1uF 220uF 220uF 220uF 0.1uF 0.1uF 0.1uF 220uF 10uF 10uF 10uF 10uF 10uF 10uF 10uF 10uF 1uF 1uF 1uF 10uF 0.1uF 10uF 1uF 1uF 1uF 10% 10% 10% 10% 20% 10% 20% 20% 20%
Remark 25V 25V 50V 50V 25V 10V 25V 10V 10V 16V 10V 16V 16V 25V 25V 16V 10V 50V 25V 10V 10V 10V 25V 25V 25V 10V 50V 50V 50V 50V 50V 50V 50V 50V 50V 50V 50V 50V 25V 50V 50V 50V 50V
A-4476-199-A DSP BOARD, COMPLETE (AEP, UK) A-4476-646-A DSP BOARD, COMPLETE (MX) A-4726-352-A DSP BOARD, COMPLETE (KR, AUS) ******************** < CAPACITOR > C601 C602 C603 C604 C606 C607 C608 C609 C610 C611 C612 C613 C614 C615 C616 C617 C618 C619 C620 C621 C622 C623 C624 C625 C626 C627 C628 C629 C630 C631 C632 C633 C634 C635 C636 C637 C638 C639 1-164-156-11 1-162-970-11 1-164-156-11 1-164-156-11 1-164-156-11 1-164-156-11 1-164-156-11 1-164-156-11 1-164-156-11 1-164-156-11 1-164-156-11 1-164-156-11 1-164-156-11 1-164-156-11 1-126-934-11 1-164-156-11 1-162-970-11 1-164-156-11 1-164-156-11 1-162-970-11 1-164-156-11 1-126-934-11 1-164-156-11 1-162-915-11 1-162-915-11 1-164-156-11 1-164-156-11 1-164-156-11 1-162-970-11 1-162-970-11 1-164-156-11 1-126-934-11 1-164-156-11 1-164-156-11 1-162-970-11 CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP ELECT CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP ELECT CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP ELECT CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP 0.1uF 0.01uF 0.1uF 0.1uF 0.1uF 0.1uF 0.1uF 0.1uF 0.1uF 0.1uF 0.1uF 0.1uF 0.1uF 0.1uF 220uF 0.1uF 0.01uF 0.1uF 0.1uF 0.01uF 0.1uF 220uF 0.1uF 10PF 10PF 0.1uF 0.1uF 0.1uF 0.01uF 0.01uF 0.1uF 220uF 0.1uF 0.1uF 0.01uF 0.01uF 0.01uF 0.01uF 25V 25V 25V 25V 25V 25V 25V 25V 25V 25V 25V 25V 25V 25V 10V 25V 25V 25V 25V 25V 25V 10V 25V 50V 50V 25V 25V 25V 25V 25V 25V 10V 25V 25V 25V 25V 25V 25V
1-162-970-11 CERAMIC CHIP 1-162-970-11 CERAMIC CHIP 1-162-971-11 1-162-971-11 1-164-156-11 1-126-934-11 1-162-970-11 1-126-934-11 1-126-934-11 1-164-360-11 1-126-934-11 1-164-360-11 1-164-360-11 1-162-970-11 1-162-970-11 1-164-360-11 1-126-934-11 1-162-971-11 1-164-156-11 1-126-934-11 1-126-934-11 1-126-934-11 1-164-156-11 1-164-156-11 1-164-156-11 1-126-934-11 1-126-964-11 1-126-964-11 1-126-964-11 1-126-964-11 1-126-964-11 1-126-964-11 1-126-964-11 1-126-964-11 1-126-193-11 1-126-193-11 1-126-193-11 1-126-964-11 1-164-156-11 1-126-964-11 1-126-193-11 1-126-193-11 CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP ELECT CERAMIC CHIP ELECT ELECT CERAMIC CHIP ELECT CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP ELECT CERAMIC CHIP CERAMIC CHIP ELECT ELECT ELECT CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP ELECT ELECT ELECT ELECT ELECT ELECT ELECT ELECT ELECT ELECT CHIP ELECT CHIP ELECT CHIP ELECT CERAMIC CHIP ELECT ELECT CHIP ELECT CHIP
10%
10% 10% 20% 10% 20% 20% 20%
20%
10%
10%
20% 20% 20% 20% 20% 20% 20% 20% 20% 20% 20% 20% 20% 20% 20% 20% 20%
20% 0.5PF 0.5PF
10% 10%
20%
10% 10% 10% 10%
1-162-970-11 CERAMIC CHIP 1-162-970-11 CERAMIC CHIP 1-162-970-11 CERAMIC CHIP
1-126-193-11 ELECT CHIP
30
ST-S5 DSP
Ref. No. C684 C685 C686 C687 C689 C690 C691 C692 C693 C694 C695 C699 C700 C701 C702 C703 C704 C705 C706 C707 C708 C709 C710 C711 C712 C713 C714 C715 C716 C717 C719 C720 C721 C722 C723 C724 C725 C726 C727 C728 C729 C730 C731 C732 C733 C735 C736 C738 C739 C740 C741 C742 Part No. 1-126-964-11 1-126-964-11 1-126-933-11 1-126-933-11 1-126-933-11 1-126-934-11 1-164-156-11 1-136-165-00 1-136-165-00 1-136-165-00 1-136-165-00 1-126-964-11 1-126-964-11 1-126-193-11 1-126-960-11 1-126-960-11 1-126-961-11 1-126-964-11 1-126-964-11 1-126-964-11 1-126-964-11 1-126-964-11 1-126-964-11 1-162-962-11 1-162-962-11 1-162-957-11 1-162-957-11 1-162-957-11 1-162-957-11 1-164-156-11 1-164-156-11 1-162-957-11 1-126-934-11 1-164-156-11 1-126-964-11 1-164-156-11 1-126-964-11 1-164-156-11 1-126-964-11 1-164-156-11 1-126-964-11 1-126-964-11 1-164-156-11 1-164-156-11 1-164-156-11 1-164-156-11 1-164-156-11 1-164-357-11 1-164-357-11 Description ELECT ELECT ELECT ELECT ELECT ELECT CERAMIC CHIP MYLAR MYLAR MYLAR MYLAR ELECT ELECT ELECT CHIP ELECT ELECT ELECT ELECT ELECT ELECT ELECT ELECT ELECT CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP ELECT CERAMIC CHIP ELECT CERAMIC CHIP ELECT CERAMIC CHIP ELECT CERAMIC CHIP ELECT ELECT CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP 10uF 10uF 100uF 100uF 100uF 220uF 0.1uF 0.1uF 0.1uF 0.1uF 0.1uF 10uF 10uF 1uF 1uF 1uF 2.2uF 10uF 10uF 10uF 10uF 10uF 10uF 470PF 470PF 220PF 220PF 220PF 220PF 0.1uF 0.1uF 220PF 220uF 0.1uF 10uF 0.1uF 10uF 0.1uF 10uF 0.1uF 10uF 10uF 0.1uF 0.1uF 0.1uF 0.1uF 0.1uF 0.001uF 0.001uF 0.1uF 0.1uF 0.001uF 20% 20% 20% 20% 20% 20% 5% 5% 5% 5% 20% 20% 20% 20% 20% 20% 20% 20% 20% 20% 20% 20% 10% 10% 5% 5% 5% 5% Remark 50V 50V 16V 16V 16V 10V 25V 50V 50V 50V 50V 50V 50V 50V 50V 50V 50V 50V 50V 50V 50V 50V 50V 50V 50V 50V 50V 50V 50V 25V 25V 50V 10V 25V 50V 25V 50V 25V 50V 25V 50V 50V 25V 25V 25V 25V 25V 50V 50V 25V 25V 50V Ref. No. Part No. Description < DIODE/RESISTOR > D601 D604 D605 D606 D607 D608 D609 D610 8-719-158-02 8-719-988-61 8-719-988-61 1-216-864-11 8-719-058-24 DIODE RD3.9SB2 DIODE 1SS355TE-17 DIODE 1SS355TE-17 METAL CHIP 0 5% DIODE RB501V-40TE-17 (E, AUS) Remark
1/16W
8-719-058-24 DIODE RB501V-40TE-17 (E, AUS) 8-719-058-24 DIODE RB501V-40TE-17 (E, AUS) 8-719-058-24 DIODE RB501V-40TE-17 (E, AUS) < GROUND TERMINAL >
* EP602 * EP603 * EP604
1-537-738-21 TERMINAL, EARTH 1-537-738-21 TERMINAL, EARTH 1-537-738-21 TERMINAL, EARTH < FERRITE BEAD/RESISTOR >
FB601 FB602 FB603 FB604 FB605 FB606 FB607 FB608
1-216-864-11 1-216-864-11 1-500-445-21 1-216-864-11 1-216-864-11
METAL CHIP METAL CHIP FERRITE METAL CHIP METAL CHIP
0 0 0uH 0 0 47 0uH 0uH
5% 5% 5% 5% 5%
1/16W 1/16W 1/16W 1/16W 1/16W
1-216-805-11 METAL CHIP 1-500-445-21 FERRITE 1-500-445-21 FERRITE < IC >
IC601 IC602 IC603 IC604 IC605 IC606 IC607 IC608 IC609 IC610
8-759-698-76 8-759-827-81 8-759-238-47 8-759-825-15 8-759-657-47 8-759-825-13 8-749-018-85 8-759-549-25 8-749-923-04 8-759-835-63
IC IC IC IC IC IC IC IC IC IC
CXD9617R IS61LV6416-15T (T&R) TC74HCT7007AF (EL) LC89056W-E AK4527 PCM1748E/2K M61512FP SN74LVU04APWR TOTX178A (OPTICAL OUT) NJM2391DL1-26-TE1
5% 20%
20% 20% 20%
< JACK > J601 J602 1-774-411-11 JACK, PIN 6P (VIDEO (AUDIO) IN, MD IN/OUT) 1-774-785-11 JACK, PIN 1P (SUB WOOFER OUT) < JUNPER RESISTOR > JR601 JR603 JR620 JR621 JR622 1-216-864-11 1-216-864-11 1-216-864-11 1-216-864-11 1-216-864-11 METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP < TRANSISTOR > Q601 Q602 Q603 Q604 Q605 Q606 Q607 Q608 Q609 8-729-801-93 8-729-120-28 8-729-120-28 8-729-120-28 8-729-120-28 8-729-141-73 8-729-141-73 8-729-141-73 8-729-141-73 TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR