Text preview for : PN-2475F.pdf part of Clarion PN-2474B-A.2475F-A.F-B.D-A Clarion



Back to : PN-2475F.pdf | Home

Clarion Co., Ltd. Published by Service Dept.
5-35-2, Hakusan, Bunkyouku, Tokyo, 112-8608 Japan 298-5977-00 May.2002 P
Service Dept.- 50 kamitoda,Toda-shi,Saitama,335-8511 Japan Tel: 048-443-1111 FAX:048-433-6996 Printed in Japan




Service Manual
NISSAN Automobile Genuine
6 Disc CD Changer

Model PN-2474B-A
(Genuine No.28184 CR000)

Model PN-2475D-A
(Genuine No.28184 6Y300)
PN-2474B


Model PN-2475F-A
(Genuine No.28184 AV700)
(Horizontal type)

PN-2475D/F Model PN-2475F-B
(Genuine No.28184 AV710)
(Vertical type)




SPECIFICATIONS COMPONENTS
Frequency response: 17Hz to 20kHz( 2dB) PN-2474B-A/PN-2475D-A/F-A/F-B
Channel separation: More than 70dB(1kHz,20kHz LPF) Main unit 1
Total harmonic distortion: Lock pin 335-0594-21 3
Less than 0.02 (20kHz LPF)
Output level: 3V 2dB(1kHz,0dB)
Power supply voltage: 13.2V DC
(10.8 to 15.6V allowable)
Ground: Negative To engineers in charge of repair or
Current consumption: 1A
Dimensions(mm):
inspection of our products.
PN-2474 225(W) 67(H) 161(D) Before repair or inspection, make sure to follow
PN-2475 225(W) 64(H) 172(D) the instructions so that customers and Engineers
Weight: 1.85kg(PN-2474) in charge of repair or inspection can avoid suf-
1.65kg(PN-2475)
fering any risk or injury.
1. Use specified parts.
NOTES The system uses parts with special safety features against
Do not play heart-shaped, octagonal, or other specially fire and voltage. Use only parts with equivalent charac-
shaped CDs. teristics when replacing them.
We cannot supply PWB with component parts in prin- The use of unspecified parts shall be regarded as re-
ciple. When a circuit on PWB has failure , please repair modeling for which we shall not be liable. The onus of
it by component parts base. Parts which are not men- product liability (PL) shall not be our responsibility in cases
tioned in service manual are not supplied. where an accident or failure is as a result of unspecified
Specifications and design are subject to change without parts being used.
notice for further improvement.




-1- PN-2474B
PN-2475D/F
2. Place the parts and wiring back in their original positions 9-2. Actuator
after replacement or re-wiring. The actuator has a powerful magnetic circuit. If a
For proper circuit construction, use of insulation tubes, magnetic material is put close to it. Its characteris-
bonding, gaps to PWB, etc, is involved. The wiring con- tics will change. Ensure that no foreign sub-
nection and routing to the PWB are specially planned stances enter through the ventilation slots in the
using clamps to keep away from heated and high voltage cover.
parts. Ensure that they are placed back in their original 9-3. Cleaning the lens
positions after repair or inspection. Dust on the optical lens affects performance. To
If extended damage is caused due to negligence during clean the lens, apply a small amount of isopropyl
repair, the legal responsibility shall be with the repairing alcohol to lens paper and wipe the lens gently.
company.
3. Check for safety after repair.
Check that the screws, parts and wires are put back se-
CAUTIONS
curely in their original position after repair. Ensure for Use of controls,adjustment or performance of procedures
safety reasons there is no possibility of secondary other than those specified herein,may result in hazardous
ploblems around the repaired spots. radiation exposure.
If extended damage is caused due to negligence of re- The COMPACT DISC player and MINI DISC player should
pair, the legal responsibility shall be with the repairing not be adjusted or repaired by anyone except properly quali-
company. fied service personnel.
4. Caution in removal and making wiring connection to the This appliance contains a laser system and is classified as
parts for the automobile. a "CLASS 1 LASER PRODUCT".To use this model
Disconnect the battery terminal after turning the ignition properly,read this Owner's Manual carefully and keep this
key off. If wrong wiring connections are made with the manual for your future reference.In case of any trouble with
battery connected, a short circuit and/or fire may occur. this player,please contact your nearest"AUTHORIZED ser-
If extensive damage is caused due to negligence of re- vice station".To prevent direct exposure to the laser beam,do
pair, the legal responsibility shall be with the repairing not to open the enclosure.
company.
5. Cautions regarding chips.
Do not reuse removed chips even when no abnormality
is observed in their appearance. Always replace them
with new ones. (The chip parts include resistors, capaci-
tors, diodes, transistors, etc). The negative pole of tanta-
lum capacitors is highly susceptible to heat, so use spe-
cial care when replacing them and check the operation
afterwards.
6. Cautions in handling flexible PWB
Before working with a soldering iron, make sure that the
iron tip temperature is around 270 . Take care not to
apply the iron tip repeatedly(more than three times)to the
same patterns. Also take care not to apply the tip with
force.
7. Turn the unit OFF during disassembly and parts replace-
ment. Recheck all work before you apply power to the
unit.
8. Cautions in checking that the optical pickup lights up.
The laser is focused on the disc reflection surface through
the lens of the optical pickup. When checking that the
laser optical diode lights up, keep your eyes more than
30cms away from the lens. Prolonged viewing of the la-
ser within 30cms may damage your eyesight.
9. Cautions in handling the optical pickup
The laser diode of the optical pickup can be damaged by
electrostatic charge caused by your clothes and body.
Make sure to avoid electrostatic charges on your clothes
or body, or discharge static electricity before handling the
optical pickup.
9-1. Laser diode
The laser diode terminals are shorted for transpor-
tation in order to prevent electrostatic damage.
After replacement, open the shorted circuit. When
removing the pickup from the mechanism, short
the terminals by soldering them to prevent this
damage.

PN-2474B -2-
PN-2475D/F
LOADING UNIT MAIN PWB CONN FPC
CONNECTOR

DRIVE UNIT

IC1
BLOCK DIAGRAM




IC4
RF AMP IC9 Q11,12
DSP&DAC IC6 L +/-
TA2157F B.T.L. Q18,19
PICK-UP UNIT TC94A14FA LPF
NJM4556 MUTE
NJM4556 2SD1306 R +/-


IC2
16PIN
SERVO DRIVER CONNECTOR
SPINDLE BD7961FM
DRIVE FPC
MOTOR
TXD
RXD
SLED REQ
LIMIT SW BUS BUFFER
MOTOR IC5




-3-
3.3V SYSTEM CONTROLLER
REG uPD780065
ACC-DET ACC
LOADING FPC MOTOR 5V
DRIVER REG
IC8
RESET
B/U 12V
LOADING MOTOR S-80140AN


VDD-REF
LOAD-END SW 5V VDD 5V



HOLDER-IN SW



12/8-DISC SENSOR
IC7
CD 9V
BA09ST
S2 IC3
S3 S1 DISC No. TR
EJECT SW MAGAZINE SW POSITION SW GP1S94
UP/DOWN MOTOR




PN-2474B
PN-2475D/F
EXPLANATION OF IC pin 62: NU : - : Not in use.
052-5050-01 uPD780065GC-710-8BT System controller pin 63: TEST 1 : IN : For the test.
pin 64: TEST 2 : IN : For the test.
1.Terminal Description pin 65: TEST 3 : IN : For the test.
pin 1: NU : - : Not in use. pin 66: TEST 4 : IN : For the test.
pin 2: NU : - : Not in use. pin 67: NU : - : Not in use.
pin 3: NU : - : Not in use. pin 68: REQ O : O : Transmit request signal output.
pin 4: NU : - : Not in use. pin 69: TXD : O : The serial data output.
pin 5: NU : - : Not in use. pin 70: RXD : IN : The serial data input.
pin 6: NU : - : Not in use. pin 71: NU : - : Not in use.
pin 7: NU : - : Not in use. pin 72: A MUTE : O : The audio mute signal output.
pin 8: NU : - : Not in use. pin 73: PON 1 : O : Power ON signal output.
pin 9: A Vref : IN : Reference voltage for ADC. pin 74: NU : - : Not in use.
pin 10: RESET : IN : Reset signal input. pin 75: NU : - : Not in use.
pin 11: NU : - : Not in use. pin 76: NU : - : Not in use.
pin 12: NU : - : Not in use. pin 77: SCK : IN : The clock pulse input.
pin 13: CONN GND : - : Connect to the ground. pin 78: SO : O : Serial data output.
pin 14: X 1 : - : Crystal connection. pin 79: SI : IN : Serial data input.
pin 15: X 2 : - : Crystal connection. pin 80: A VSS : - : Analog ground.
pin 16: VDD : - : Positive supply voltage.
pin 17: VSS : - : Negative supply voltage.
pin 18: NU : - : Not in use. Table 1. Up/down motor control signal
Up Down Brake Stop
pin 19: NU : - : Not in use.
UD CCW (pin 50) L H H L
pin 20: NU : - : Not in use.
UD CW (pin 49) H L H L
pin 21: SBSY : IN : Sub code block sync input.
pin 22: ACC CNT : IN : ACC ON signal input.
pin 23: MAG SW : IN : The inserted flag input for the magazine. Table 2. Loading motor control signal
pin 24: MAG EJ : IN : The eject key input. Load Unload Brake Stop

pin 25: NU : - : Not in use. LD CCW (pin 52) L H H L
LD CW (pin 51) H L H L
pin 26: NU : - : Not in use.
pin 27: NU : - : Not in use.
pin 28: NU : - : Not in use.
pin 29: NU : - : Not in use.
pin 30: NU : - : Not in use.
pin 31: NU : - : Not in use.
pin 32: NU : - : Not in use.
pin 33: NU : - : Not in use.
pin 34: NU : - : Not in use.
pin 35: NU : - : Not in use.
pin 36: NU : - : Not in use.
pin 37: NU : - : Not in use.
pin 38: TCLK : O : The test clock output.
pin 39: Disk No Tr : IN : The photo transistor signal input for the
disk number detection.
pin 40: 8cm DISC : IN : 8cm disk = "L", 12cm disk = "H".
pin 41: POS SW : IN : Datum point signal input to detect the disc
number.
pin 42: LIMIT : IN : Inside limit switch signal input for the disk.
pin 43: HOLDER IN : IN : "L" = Holder has been placed in the mag-
azine.
pin 44: LOAD END : IN : "L" = Holder has been removed from the
magazine.
pin 45: VSS : - : Negative supply voltage.
pin 46: VDD : - : Positive supply voltage.
pin 47: PON 2 : O : Power ON signal output.
pin 48: PON 1 INV : O : The inverted signal of PON 1(pin 73).
pin 49: UD CW : O : Up/down motor control signal output.
Refer Table 1.
pin 50: UD CCW : O : Up/down motor control signal output.
Refer Table 1.
pin 51: LD CW : O : Loading motor control signal output.
Refer Table 2.
pin 52: LD CCW : O : Loading motor control signal output.
Refer Table 2.
pin 53: DR MUTE : O : Drive mute signal output to the CD IC.
pin 54: GV SW :I/O: Gain select signal input/output.
pin 55: RESET : O : Reset signal output.
pin 56: CCE : O : The chip enable signal output.
pin 57: BUC CLOCK : O : CD IC clock pulse output.
pin 58: BUS 3 :I/O: CD IC Data input / output.
pin 59: BUS 2 :I/O: CD IC Data input / output.
pin 60: BUS 1 :I/O: CD IC Data input / output.
pin 61: BUS 0 :I/O: CD IC Data input / output.

PN-2474B -4-
PN-2475D/F
EXPLODED VIEW PARTS LIST
Main section / PN-2474B



B6
13
B4
3 18
16 17 5
B2

B5
B3 B6 2 B4


B1 B5 18 B3
15
1 A4
20
11
A3 18

9 10
19
C1



A4
C2
14
22 A2
23
C1 18
21 B2 A3
12
A1
16
B1
A2

7
4
8 C2 A1
6 18




NO. PART NO. DESCRIPTION Q'TY NO. PART NO. DESCRIPTION Q'TY
1 CD CHANGER MECHANISM 1 12 620-1097-20 DMP-P-SALOON R 1
(027020)
13 620-1099-20 CONNECT HOLDER 1
2 039-2030-21 FLEXIBLE PWB 1
(WITHOUT COMPONENT) 14 622-1545-20 FL PIN R 1
3 074-1087-02 OUTLET SOCKET(16P) 1 15 622-1546-20 FL PIN L 1
4 286-9907-01 SET PLATE 1 16 629-0080-00 DAMPER 4
5 310-1749-21 UPPER CASE 1 17 716-0484-00 SCREW(M2 2.5) 1
6 311-1846-21 LOWER CASE 1 18 716-1716-00 SCREW 9
7 320-0590-20 DUSTPROOF COVER 1 19 750-3459-21 FL-SPRING R 1
8 341-1774-20 SHAFT 1 20 750-3460-21 FL-SPRING L 1
9 371-5715-21 TRIM PLATE 1 21 750-6707-20 SPRING 1
10 382-6254-20 BUTTON 1 22 716-3486-00 SCREW 2
11 620-1096-20 DMP-P-SALOON L 1 23 746-0767-00 WASHER 2



-5- PN-2474B
PN-2475D/F
Main section / PN-2475F-A/F-B/D-A




B6
14
3
B4 18
17 19 7 5
B2
4
B5
B3 2 B4
B6


B1 B5
19
B3
16
A4
1
21
13
19
A3
10
11
20



A4

22 15
8
A2

19 B2 A3

12 17
A1


B1
A2



6
9
A1
19




Note) Some parts depend on each model.
The model name is specified in the description.
NO. PART NO. DESCRIPTION Q'TY NO. PART NO. DESCRIPTION Q'TY
1 CD CHANGER MECHANISM 1 11 382-6254-20 BUTTON 1
(027120)
12 620-0996-21 DAMPER PLATE R 1
2 039-2030-21 FLEXIBLE PWB 1
(WITHOUT COMPONENT) 13 620-1095-20 DAMPER PLATE L 1
3 074-1087-02 OUTLET SOCKET(16P) 1 14 620-1099-20 CONNECT HOLDER 1
4 286-6088-00 SETPLATE(PN-2475F-A) 1 15 622-1545-20 FL PIN R 1
286-6088-01 SETPLATE(PN-2475F-B)
286-6077-00 SETPLATE(PN-2475D-A) 16 622-1546-20 FL PIN L 1
5 310-1748-21 UPPER CASE 1 17 629-0080-00 DAMPER 4
6 311-1844-22 LOWER CASE 1 18 716-0484-00 SCREW(M2 2.5) 1
7 335-5993-00 LOCK FASTENER(D-A) 1 19 716-1716-00 SCREW 9
8 746-0767-00 WASHER 2 20 750-3459-21 FL-SPRING R 1
9 940-7993-11 ESCUTCHEON ASSY 1 21 750-3460-21 FL-SPRING L 1
10 371-5693-23 TRIM PLATE 1 22 716-3486-00 SCREW 2


PN-2474B -6-
PN-2475D/F
Changer mechanism section
55
B3 10
B3
55
55
36

A7 B2
B2
A4
B10 62
62
A6 55 55 B7 B6
B1 B1
B7 B6 A5
B5 B8
A3
C1 55
B5
B10
67 B4
A2
33 B9
C2 64
71 C3 B4
D2 30
19
44
12 32 34

D1


B8
A10 31
55 N1
A11 B9
A14 E1
A1 67
E


A7 12 1
2
3
55
4
5
6




A10
A6 A14 A4
A13
A12 A9 62
9
A5
A3 55
A8

8
E

A2
1
2
3
4
5
6
A9
51 A1
A13
65 45 57
65
69 N1 68
A8
12
54
A12
57

C1 57 16

11 A11
59
63
D2


NO. PART NO. DESCRIPTION Q'TY NO. PART NO. DESCRIPTION Q'TY
1 966-0582-23 DRIVE-P-ASSY 1 12 966-0594-24 V-CHASSIS ASSY 1
2 966-0583-20 DISC HOLD ASSY 1 13 966-0454-00 SH-RACK-ASSY 1
3 966-0584-23 CLAMP-P-ASSY F 1 14 966-0623-23 L-LOWER-P-ASSY 1
4 966-0585-22 CAM GEAR ASSY 1 15 969-0061-30 PICK UP-ASSY 1
5 966-0586-22 MOTOR-P-ASSY 1 16 039-2063-21 MAIN PWB 1
(WITHOUT COMPONENT)
6 966-0588-22 HOLDER-L-ASSY 1
17 001-0563-00 LED 1
7 966-0589-24 L-UPPER-P-ASSY 1
18 013-7413-50 DETECTOR SWITCH 3
8 966-0590-20 MG-LO-P-ASSY 1
19 SMA-180-100 MOTOR ASSY(UP/DOWN) 1
9 966-0591-21 REAR PANEL ASSY 1
20 SMA-181-100 MOTOR ASSY(SLED) 1
10 966-0592-20 UP-PLATE ASSY(PN-2475) 1
966-0626-21 UP-PLATE ASSY(PN-2474) 21 SMA-179-100 MOTOR ASSY(SPINDLE) 1
11 966-0593-20 UD-GEAR-P-ASSY 1 22 039-1949-20 DRIVE PWB 1
(WITHOUT COMPONENT)

-7- PN-2474B
PN-2475D/F
35
29
O1
65
65 4 F2

F1

66 O1 70 H1
K2
G2
G1 C2
28
G1
7
26 C3 H2 46
I1 F2
2 F1
I1 N2 M1 M2


47 55
52 6
J1
F4 H1
G2
D1
F5 41
K2
60
3
55
60 57
18 E1 65
L1
24 65 49 1
17 K3 P1 43
K1 57 20 50
48 27 61
72
57 J2
38
N1 42
J4 N2 57 21
N1
F4
J4 L1
Q1
61 58
23 K1 37
64 55 65 13
55 H2 M2 57 39
63 J1
F5 25
J2
J3
55 M1 56 15
5 40
P1
55 K3
55
14 Q1
J3
53
55 22
57
18

NO. PART NO. DESCRIPTION Q'TY NO. PART NO. DESCRIPTION Q'TY
23 039-1950-20 LOADING PWB 1 40 621-0590-20 LS GEAR 1
(WITHOUT COMPONENT)
41 621-0591-20 PICK UP GUIDE 1
24 060-0252-01 PHOTO-TR 1
42 621-0592-21 LS-HOLDER 1
25 620-0999-21 LS-SPRING 1
43 621-0593-21 LS GUIDE 1
26 620-1575-21 SWITCH PLATE 1
44 802-4906-60 VINYL-COAT-WIRE(RED) 1
27 620-1007-22 CLAMP PLATE M 1
45 621-0597-20 V-GEAR A 1
28 620-1008-24 CLAMP PLATE R 1
46 621-0630-22 HOLDER-G-RAIL R 1
29 620-1009-22 CLAMPER PLATE 1
47 621-0631-21 HOLDER-G-RAIL L 1
30 620-1016-20 GAP PLATE R 1
48 621-0703-20 L-GEAR A 1
31 620-1017-20 GAP PLATE F 1
49 621-0633-20 L-GEAR B 1
32 620-1018-20 MG EJECT PLATE 1
50 805-4912-60 VINYL-COAT-WIRE(GRN) 1
33 620-1019-20 SLIDE PLATE R 1
51 621-0635-20 V-HELICAL GEAR 1
34 620-1020-21 SLIDE PLATE F 1
52 621-0636-21 CLAMPER RING 1
35 620-1031-21 LOADING ARM 1
53 624-3022-00 LEAD SCREW 1
36 620-1034-24 SIDE PANEL 1
54 629-0061-00 GEAR DAMPER 1
37 621-0587-21 SCREW HOLD BASE 1
55 716-0484-00 SCREW(M2 2.5) 23
38 801-4912-60 VINYL-COAT-WIRE(BRN) 1
56 716-0675-00 SCREW(M2 5.5) 1
39 621-0589-20 SECOND GEAR 1
PN-2474B -8-
PN-2475D/F
NO. PART NO. DESCRIPTION Q'TY NO. PART NO. DESCRIPTION Q'TY
57 716-1716-00 SCREW(M2 3) 10 65 746-0761-00 WASHER 7
58 716-3469-00 SCREW 2 66 750-3461-21 DISC-H-SPRING 1
59 735-2006-11 D-SEMS-SCREW(M2 6) 1 67 750-3462-21 GAP SPRING 2
60 739-1722-17 SCREW(M1.7 2.2) 2 68 750-3463-20 MG LOCK SPRING 1
61 739-2022-17 SCREW(M2 2.2) 2 69 750-3464-20 MG EJECT SPRING 1
62 743-1500-10 E-RING 3 70 750-3492-22 CLAMPER SPRING 1
63 743-2000-10 E-RING 2 71 800-4906-60 VINYL-COAT-WIRE(BLK) 1
64 745-0789-01 DRIVE WASHER 2 72 SMA-188-100 MOTOR ASSY(LOADING) 1


ELECTRICAL PARTS LIST Note) Several different parts of the same reference number are alternative parts.
Main PWB(B1) section One of those parts is used in the set.
REF No. PART No. DESCRIPTION REF No. PART No. DESCRIPTION REF No. PART No. DESCRIPTION
C1 183-1073-17 6.3V100uF C58 183-1073-17 6.3V100uF Q2 191-1237-50 2SB1237QR
C2 046-1032-78 0.01uF C59 168-1042-78 0.1uF Q3 191-1237-50 2SB1237QR
C3 043-0533-50 0.047uF C60 042-0452-81 10V220uF Q4 125-0014-92 DTA114
C4 042-0426-31 6.3V100uF C61 045-2201-50 22pF Q5 190-1048-50 2SA1048Y/GR
C5 046-6822-58 6800pF C62 042-0452-81 10V220uF Q6 125-2004-92 RN1402
C6 168-1042-78 0.1uF C63 173-1021-18 1000pF Q7 193-1858-50 2SD1858QR
C7 178-1052-78 1uF C64 184-4773-31 16V470uF Q8 125-2004-92 RN1402
C8 183-3363-27 10V33uF C65 045-2201-50 22pF Q9 125-0014-92 DTA114
C9 183-3363-27 10V33uF C66 042-0452-81 10V220uF Q10 192-2712-51 2SC2712GL
C10 168-1042-78 0.1uF C67 042-0452-81 10V220uF Q11 193-1306-00 2SD1306
C11 168-1042-78 0.1uF C68 183-1063-39 16V10uF Q12 193-1306-00 2SD1306
C12 045-5096-50 5pF C69 168-5632-78 0.056uF Q13 192-2712-51 2SC2712GL
C13 183-3363-27 10V33uF C70 168-5632-78 0.056uF Q14 192-2712-51 2SC2712GL
C14 178-1052-78 1uF C71 168-5632-78 0.056uF Q15 125-0014-92 DTA114
C15 046-1032-78 0.01uF C72 168-5632-78 0.056uF Q16 192-2712-51 2SC2712GL
C16 178-1052-78 1uF C73 168-1042-78 0.1uF Q17 125-2004-92 RN1402
C17 045-5601-50 56pF C74 178-1052-78 1uF Q18 193-1306-00 2SD1306
C18 168-1032-55 0.01uF C75 178-1052-78 1uF Q19 193-1306-00 2SD1306
C19 043-0533-50 0.047uF C76 178-1052-78 1uF R1 033-1041-15 1/16W 100k
C20 046-1532-78 0.015uF C77 178-1052-78 1uF R2 033-1041-15 1/16W 100k
C21 045-4701-50 47pF C78 168-4722-55 4700pF R3 033-1041-15 1/16W 100k
C22 043-0533-50 0.047uF C79 168-4722-55 4700pF R4 033-1041-15 1/16W 100k
C23 046-1522-58 1500pF C80 168-4722-55 4700pF R5 033-1041-15 1/16W 100k
C24 046-4722-58 4700pF C81 168-4722-55 4700pF R6 033-1041-15 1/16W 100k
C25 046-1032-78 0.01uF D1 001-0516-90 MA111 R7 033-2211-15 1/16W 220
C26 043-0533-50 0.047uF D2 001-1304-90 DAN202U R8 111-2711-94 1/4WS 270
C27 046-3332-78 0.033uF D3 001-0504-33 HZS6B2L R9 033-6831-15 1/16W 68k
C28 046-3332-78 0.033uF D4 001-0516-90 MA111 R10 111-2201-94 1/4WS 22
C29 046-4712-58 470pF D5 001-0422-38 MTZJ36 R11 111-2201-94 1/4WS 22
C30 045-4701-50 47pF D6 001-0422-38 MTZJ36 R12 119-1031-15 1/16W 10k
C31 168-1032-55 0.01uF D7 001-0516-90 MA111 R13 119-2231-15 1/16W 22k
C32 043-0533-50 0.047uF D9 001-0516-90 MA111 R14 033-8211-15 1/16W 820
C33 043-0533-50 0.047uF D10 001-0466-90 S5688B R15 111-1001-94 1/4WS 10
C34 168-1032-55 0.01uF D11 001-0516-90 MA111 R16 119-1031-15 1/16W 10k
C35 168-1042-78 0.1uF FIL1 060-3113-95 1000pF R17 119-1531-15 1/16W 15k
C36 166-1011-50 100pF FIL2 060-3113-95 1000pF R18 033-2721-15 1/16W 2.7k
C37 166-1501-50 18pF FIL3 060-3113-95 1000pF R19 033-6831-15 1/16W 68k
C38 166-1501-50 18pF IC1 051-5710-90 TA2157F R20 033-6831-15 1/16W 68k
C39 046-1032-78 0.01uF IC2 051-6060-08 BD7961FM R21 033-1011-15 1/16W 100
C40 168-1042-78 0.1uF IC3 051-5806-00 GP1S94 R22 033-1021-15 1/16W 1k
C41 168-1032-55 0.01uF IC4 051-6376-00 TC94A14FA R23 033-1031-15 1/16W 10k
C42 046-1032-78 0.01uF IC5 052-5050-01 UPD780065GC-710- R24 033-1831-15 1/16W 18k
C43 183-3363-27 10V33uF 8BT R25 111-2711-94 1/4WS 270
C44 046-1032