RoadStar_CTV1015.pdf part of CTV1015 RoadStar_CTV1015.pdf, ServiceManual text manual preview

Text preview for : RoadStar_CTV1015.pdf part of CTV1015 ServiceManual

Back to : RoadStar_CTV1015.pdf | Home

CTV-1015
R

Service Manual - CTV-1015

SAFETY PRECAUTION
X-RAY RADIATION PRECAUTION
1. Excessive high voltage can produce potentially hazardous X-RAY RADIATION. To avoid such hazards, the high voltage must not be above the specified limit. The normal value of the high voltage in this receiver is 18KV. The high voltage must not exceed 25KV. Each time a receiver requires servicing, the high voltage should be checked according to the high voltage check procedure on this manual. It is recommended that the reading of the high voltage be recorded as a part of the service record. It is important to use an accurate and reliable high voltage meter. 2. The only source of X-RAY RADIATION in this television is the picture tube. For continued X-RAY RADIATION protection, the replacement of tube must be exactly the same type tube as specified in the parts list. 3. Some parts in this television have special safety-related characteristics for X-RAY RADIATION protection. For continued safety, parts replacement should be undertaken only after referring to the PRODUCT SAFETY NOTICE below. 4. Serviceman - WARNING : To Reduce the Risk of Possible Exposure to X-Radiation, take X-Radiation Protective Measures(See Service Manual) For Personnel During Servicing.
CAUTION : SHORT ANODE LEAD ONLY TO CHASSIS. DO NOT PLACE THIS PRODUCT ON AN UNSTABLE CART, STAND, TRIPOD, BRACKET, OR TABLE. THE PRODUCT MAY FALL, CAUSING SERIOUS PERSONAL INJURY AND SERIOUS DAMAGE TO THE PRODUCT. USE ONLY WITH A CART, STAND, TRIPOD, BRACKET, OR TABLE RECOMMENDED BY THE MANUFACTURER, OR SOLD WITH THE PRODUCT. FOLLOW THE MANUFACTURER'S INSTRUCTIONS WHEN INSTALLING THE PRODUCT AND USE MOUNTING ACCESSORIES RECOMMENDED BY THE NUFACTURER. A PRODUCT AND CART COMBINATION SHOULD BE MOVED WITH CARE. QUICK STOPS, EXCESSIVE FORCE, AND UNEVEN SURFACES MAY CAUSE THE PRODUCT AND CART COMBINATION TO OVERTURN.

SAFETY PRECAUTION
WARNING : Service should not be attempted by anyone unfamiliar with the necessary precautions on this television. The followings are the necessary precautions to be observed before servicing. 1. Since the chassis of this television is directly connected to the AC power line (Hot chassis),an isolation transformer should be used during any dynamic service to avoid possible shock hazard. 2. Always discharge the picture tube anode to the CRT conductive coating before handing the picture tube. The picture tube is highly evacuated and, if broken, glass fragments will beviolently expelled. Use shatterproof goggles and keep picture tube away from the body while handing. 3. When replacing a chassis in the cabinet, always be certain that all the protective devices are put back in place, such as non-metallic control knobs, insulating covers, shields isolation resistor-capacitor network, etc. 4. Before returning the set to the customer, always perform an AC leakage current check on the exposed metallic parts of the cabinet such as terminals, screwheads, metal overlays control shafts, etc. to insure that the set is safe to operate without danger of electrical shock. 5. Plug the AC line cord directly into a AC 230V AC outlet. (do not use a line isolation transformer during this check) Use an AC voltmeter having 5,000 ohm per volt or more sensitivity in the following manner, Connect a 1,500 ohm 10 watts resistor, paralleled by a 0.15uF, AC type capacitor, between a known good earth ground (water pipe, conduit, etc.) and the exposed metallic parts, one at a time.

Measure the AC voltage across the combination of 1,500 ohm resistor and 0.15uF capacitor. Reverse the AC plug at the AC outlet and repeat. AC voltage measurements for each exposed metallic part. Voltage measured must not exceed 0.75 volts RMS. This corresponds to 0.5 milliamp AC. Any value exceeding this limit constitutes a potential shock hazard and must be corrected immediately.
AC VOLTMETER

Good earth ground such as a water pipe, conduit etc

0.15uF Place this probe on each exposed metal part

1500 ohm 10 watt

PRODUCT SAFETY NOTICE
Many electrical parts in this chassis have special safety-related characteristics. These characteristics are often passed unnoticed by a visual inspection and the protection afforded by them cannot necessarily be obtained by using replacement, rated for higher voltage, wattage, etc. Replacement parts which have these special safety characteristics are identified in this manual and its parts list. Before replacing any of these components, read the parts list in this manual carefully. The use of substitute replacement parts which do not have the same safety characteristics as specified in the parts list may create shock, fire, x-ray radiation or other hazards.

DIRECTION FOR GENERAL USE
1. In the majority of cases, a color television receiver will need only slight touch-up adjustment upon installation. Check the basic characteristics such as height, vertical sync, horizontal sync and focus. Observe the picture for good black and white objectionable color shading. If color shading is evident, demagnetize the receiver. If color shading still persists, perform purity and convergence adjustments. This should be all that is necessary for optimum receiver performance. 2. THIS RECEIVER TRANSISTORIZED AND SPECIAL CARE MUST BE TAKEN. READ THE FOLLOWING NOTES BEFORE ATTEMPTING ALIGNMENT. 1) Alignment requires an exacting procedure and should be undertaken only when necessary. 2) An isolation transformer must be used to prevent a shock hazard. 3) The test equipment specified or its equivalent is required to perform the alignment properly. Any use of equipment which does not meet these requirements may result in an improper alignment. 4) A correct matching of the equipment is essential. A failure to use proper matching will result in responses which cannot represent the true operation of the receiver. 5) An use of excessive signal from a sweep generator can cause overloading of receiver circuit. It should be avoided to obtain a true response curve. Insertion of markers from the maker generator should not cause distortion of the responses. 6) Connect the TV only to an AC power source with voltage and frequency as specified on the backcover nameplate. 7) Do not attempt to connect or disconnect any wire while the receiver is in operation. Make sure the power cord is disconnected before replacing any part in the receiver.

AUTOMATIC DEGAUSSING
A degaussing coil is mounted around the picture tube so that external degaussing after moving the TV should be unnecessary. But the receiver must be properly degaussed upon installation. The degaussing coil operates for about 1 second after the power is switched ON. If the set is moved or turned in a different direction, the power should be OFF for at least 15 minutes. If the chassis or parts of the cabinet become magnetized, it will result in a poor color purity. If this happens, use an external degaussing coil. Slowly move the degaussing coil around the faceplate of the picture tube and the sides and front of the receiver. Slowly withdraw the coil to a distance of about 6 feet before turning power OFF. If color shading persists, perform the following Color Purity and Convergence adjustments.

HIGH VOLTAGE CHECK
CAUTION : There is no high voltage adjustment on this chassis. The +B power supply should be +9 volts (with full color-bar input and normal picture level). 1. Connect an accurate high voltage meter to the second anode of the picture tube. 2. Turn on the receiver. Set bright and contrast controls to the minimum (zero beam current). 3. The high voltage must be measured below 29KV under any conditions. 4. Set sub-Bright DATA(SBR) minimum in FACTORY 1 MODE to ensure that the high voltage does not exceed the limit under any conditions.

Purity Adjustment
1. Warm up the receiver for at least 30 minutes. 2. Plug in the CRT deflection yoke. Tighten the clamp screw. 3. Plug the convergence yoke into the CRT and set it as shown in Fig. B-1. 4. Input a black and white signal. 5. Fully demagnetize the receiver by using an external degaussing coil. 6. Turn the CONTRAST and BRIGHTNESS controls to maximum. 7. Loosen the clamp screw holding the yoke. Slide the yoke backward or forward to produce a vertical green belt. (Fig. B-2) 8. Tighten the convergence yoke. 9. Slowly move the deflection yoke forward. Adjust for the best overall green screen. 10. Temporarily tighten the deflection yoke. 11. Produce blue and red rasters by adjusting the-low-light controls. Check for good purity in each field. 12. Tighten the deflection yoke.

Center Convergence Adjustment
1. Warm up the receiver for at least 30 minutes. 2. Adjust the two tabs of the 4-pole magnets Change the angle between them. Superimpose the red and blue vertical lines in the center area of the screen. 3. Adjust the BRIGHTNESS and CONTRAST controls for a well-defined picture. 4. Adjust the two tabs of the 4-pole magnets, and change the angle between them. Superimpose the red and the blue vertical lines in the center area of the screen. 5. Turn both tabs at the same time, keeping the angle constant, and superimpose the red and blue horizontal lines in the center of the screen. 6. Adjust two-tabs of 6-pole magnets to superimpose the red and blue lines onto the green. Adjusting the angle affects the vertical lines, and rotating both magnets affects the horizontal lines. 7. Repeat adjustments 2-6, if necessary. 8. Since the 4-pole and 6-pole magnets interact, the dot movement is complex(fig B-3).

FIG. B-1 CONVERGENCE MAGNET ASSEMBLY

Vertical Green Belt

ADJUST

FIG. B-2 CENTER CONVERGENCE ADJUSTMENT

BLUE

RED

BLUE

RED

BLUE

BLUE/RED

RED

GREEN

4-POLE MAGINETS MOVEMENT

6-POLE MAGINETS MOVEMENT

FIG. B-3 CENTER CONVERGENCE ADJUSTMENT

SPECIFICATIONS

RECEPTION SYSTEM POWER SOURCE

PAL SECAM BG/DK I L & NTSC Playback AC 90-250V~ 50/60Hz, 45W DC 12-24V , 40W

SOUND OUTPUT POWER ANTENNA IMPEDANCE OPERATING FREQUENCIES

1.0W 75 OHM UNBALANCED TYPE VIDEO IF 38.9MHz SOUND IF 33.4MHz

RECEIVING CHANNELS

VHFL CH : 2 TO 4 VHFH CH : 5 TO 12 UHF CH : 21 TO 69 Hyper Band : S1 to S41

LOCATION OF CONTROLS

FRONT
3 4 5 6 7 8

1 2

BACK
9

12 10 11 13

1. STAND-BY LAMP 2. Remote Control Sensor 3. Power Switch 4. TV/ VIDEO Key 5. Speaker 6. Program Up ( )Down( )Key 7. Volume Up ( )Down( )Key

8. Earphone Jack 9. Antenna Holder 10. Antenna Jack(75 ohm) 11. Scart Jacks 12. AC Input Jack(Mains Power Socket) 13. DC Power Jack

REMOTE CONTROL USE
BATTERY INSTALLATION
Replace two batteries in the battery compartment at the same time. lnsert "AAA" batteries, observing the polarity ( or ) marked on the unit. Batteries should last about a year under normal use. lf the operation is unstable(either channel or volume does not change), replace the batteries. When the hand unit is not used for a long, or when the batteries are used up, take out the batteries to prevent possible leakage. To avoid any malfunction of the remote control, press only one button at a time.

Remocon depends on the option of model

BASIC REMOTE CONTROL OPERATION

1. Power button
At Stand-by mode, the LED stand-by indicator is in RED color. By pressing the power button, the TV will be turned ON, and the LED stand-by indicator will be turned OFF.

2. TV/Video button
Select either TV or VIDEO mode.

3. 10 digit keys
It is used to directry select desired channel program number.

4. Two digit keys
1) -/-- key selects one-digit(0 to 9) or two-digit program number (10 to 99). 2) (-) or (--) is displayed by turns on the upper right position if you press this key repeatedly. 3) You can choose one-digit program number if (-) is shown and two-digit program number if (--) shown. ex1) Press 7 if you'd like to watch program number 7. ex2) Press -/-1 7 if you'd like to watch program number 17. If you want to watch program number 7 while (--) is already on, press -/-7 or 0 7.

5. Mute button
Switch the sound output either ON or OFF.

6,7. Program up( )/down( ) button
1) It is used to select the channel you want to watch on either upward or downward direction. 2) It makes the cursor to move while in main MENU, DVD MENU.

8,9. Volume up(+)/down(-) button
1) It adjusts the volume level of sound. 2) It is used to choose a specified mode in the main MENU by pressing VOL(+) button. 3) It controls the increase or decrease of each mode you selected. 4) It makes the cursor to move while in DVD MENU.

BASIC REMOTE CONTROL OPERATION
10. Menu button
It displays all the functions that user can control.

11. Sleep button
The television is automatically turned off after an elapse of the set sleep time. 1) The set time ranges from 10 to 180 minutes, which is repeated in sequence each time you press. SLEEP OFF 10 30 60 90 120 150 180

2) If you'd like to check the remaining SLEEP TIME after OSD disappears, press DISPLAY button.

12. Skip button
1) It can be used so that the unnecessary program number may not be displayed. 2) If you press this at a specific program number, OSD color of the current program number will change from green to magenta. 3) If you want to watch the skipped program number, use 10 digit key to view it, then press SKIP button, or operate AUTO PROGRAM in set up.

13. Wide button
This function lets you select one between wide and normal screen. Wide ON Wide OFF 16 : 9 4 : 3 screen screen

14. Display button
Displays the current channel number, picture and sound state, sleep and clock.

15. Quick view button
Switches the current channel to the previously viewed channel.

16. Sound standard button
By pressing this, the sound output becomes 30 level.

GENERAL FEATURES AND ADJUSTMENTS
1. NOTE
Because this is not a hot chassis, it is not necessary to use an isolation transfromer. However, the use of isolation transformer will help protect test instrunents. Adjustment must be done in the correct order. Supply AC 90-250V~ 50/60Hz, 45W, DC 12-24V , 40W in general. Most of this chassis is designed to operate in the wide range of power supply. Automatic degaussing The degaussing circuit operates for about 1 secord after the power is switched on. If you change the direction of the TV set in a state of Power-On, any color-blur may happen. In that case, plug it off and plug it on after 1 more hour. If color shading still persists, perform purity and convergence adjustments.

2. EEPROM(IC01) REPLACEMENT
When IC01 is replaced, all values are reset to INITAL MICRO-CONTROLLER DATA. Because the pre-set data is reset after the replacement, above all, select factory mode and write down all the pre-set data befote the replacement. After the replacement, select factory mode and set the initial data referring to the written-down data. If you fogot to write down all the pre-set data or you can t turn on TV, re-adjust the initial data according to the adjustment manual, follow the below procedure. Replace the defective IC01 with a new one. In the ON mode, Press DISPLAY + 1 + 1 + TV/VIDEO button on the romote controller in sequence. And then, factory mode will be displayed on the screen. Input the signal like a color-bar pattern into antenna terminal, or input the current broadcasting signal into antenna terminal.

3. WHEN CRT IS REPLACED
Do the following adjustments in the factory made. SCREEN adjustment(SCREEN VOLTAGE) W.BAL adjustment (R-Cut, G-Cut, R-DRV, G-DRV, B-DRV) PICTURE adjustment (HRS(50), HRS(60), HEIGHT)

NOTE
You don t need to select 8.EEPROM Rest and 9.UOC Control. Two items are critical to the system operation. Press TV/VIDEO or MTS button when you want to finish the factory adjustments. TV/VIDEO button:the early state that you bought TV sets. MTS button:the previous state before you enter the factory mode.

FACTORY/SERVICE ADJUSTMENTS
1. Procedure for the factory adjustment mode
In the ON mode, the factory(Service) mode is activated by pressing the DISPLAY + 1 + 1 + TV/Video button in sequence on the remote controller. The menu of the factory mode will be displayed. The factory mode consists of 9 componets: 1. SCREEN 2. W.BAL 3. PICTURE 4. SERVICE1 ;You do not need to Select it. 5. VOLUME TEST ;You do not need to Select it. 6. DEVICE CHECK ;You do not need to Select it. 7. OPTION 8. EEPROM RESET ;You do not neet to Select it 9. UOC CONTROL ;You do not need to Select it. 10. V-CHIP TEST ;You do not need to Select it. Select each adjustment mode by pressing CH up( )or CH down( ) button. And access it by pressing vol up(+)or vol down(-) button. NO 1 2 PART SCREEN W.BAL (WHITE BALANCE) OSD R-CUT G-CUT R-DRV G-DRV B-DRV HRS(50) HRS(60) VRS HEIGHT V-SLOPE S-C W-HEIGHT TEXT RANGE 0~63 0~63 0~63 0~63 0~63 0~63 0~63 0~63 0~63 0~63 0~63 0~63 ARABIC/ENG FARSI/ENG WEST EURO CYL/ENG EAST EURO ON/OFF WITH ARABIC W/O ARABIC ON/OFF ON/OFF INITIAL DATA 32 32 32 32 32 40 48 24 17 32 24 6 COMMENT

3

WHITE PICTURE

NTSC M/PAL M

4

SERVICE 1

NTSC LANGUAGE AUTO P.OFF SECAM L

OFF W/O ARABIC ON ON

FACTORY/SERVICE ADJUSTMENTS
NO 5 PART SERVICE 2 OSD CONTRAST BRIGHT COLOR SHARPNESS TINT AGC UOC EEPROM MSP34XX TUNER SDA9489X TDA9859 ETC 00002 ETC 00003 RANGE 0~63 0~63 0~63 0~63 0~63 0~63 MIN / MAX INITIAL DATA 0 35 55 0 30 50 0 28 63 0 24 48 0 32 63 33 MIN Connected Connected Disconnected Connected Disconnected Disconnected Disconnected Disconnected COMMENT Min Cnt Max

6 7

VOLUME TEST Device Check

8 9

EEPOM Reset UOC Control

Don't select it Don't select it

2. SCREEN Voltage Adjustment Turn the TV set to receive a color bar pattern.(Standard picture) Connect the probe of oscilloscope to the RK (Red Cathode) of CPT Board. Adjust Screen Volume of FBT so that the waveform is the same as below figure.
Horizontal FlyBack Time Black level

145Vp-p

White level 1H-LINE GND for dc

The waveform of RK(Red Cathode) of CPT Board

FACTORY/SERVICE ADJUSTMENTS
3. Deflection Adjustments
HRS(50) adjustment : Tune the TV set to a LION HEAD pattern signal with 50Hz of vertical frequency. HRS(60) adjustment : Tune the TV set to a LION HEAD pattern Signal with 60Hz of vertical ferquency. HEIGHT adjustment : Tune the TV set to a LION HEAD pattern Signal and adjust the vertical amplitude to 4 bars both the Top and the bottom.

4. WHITE BALANCE Adjustments(manual)
Input PURE WHITE pattern into antenna terminal or into Video input terminal. Keep TV on for about 30 minutes prior to white balance adjustment. Screen Voltage Adjustment (page 14) Place the probe of CRT Analyzer at the center Position of picture screen. Adjust CONTRAST & BRIGHTNESS until Y value of CRT analyzer becomes 35FL above roughly. Select 2.W.BAL and press Vol(+) button. And then R-CUT 32 will be displayed. 1 button : R-CUT 5 button : G-CUT 9 button : R-DRV 0 button : G-DRV -/-- button : B-DRV Select R-DRV & G-DRV and adjust them to get the color coordinates below in the high light state. In this case, fix the reference color(B-DRV) as possible as.

X COORDINATE 0.261

Y COORDINATE 0.268

5. Focus ADJUSTMENT
Input CROSS DOT pattern into antenna terminal on video input terminal. Rotate the variable resistor of FOCUS terminal on the flyback transformer until the horizontal and vertical line becomes slim. Check the surrounding FOCUS in the lion head pattern.

6+6W STEREO AMPLIFIER
TDA 2007A
DESCRIPTION
The TDA2007A is a class AB dual Audio power amplifier assembled in single in line 9 pins package, specially designed for stereo application in music centers TV receivers and portable radios.

Features
HIGH OUTPUT POWER HIGH CURRENT CAPABILITY AC SHORT CIRCUIT PROTECTION THERMAL OVERLOAD PROTECTION

Package Dimension
SIP 9

unit : mm

D

C

L1

N P

M

L3

c2

d1

L4

L2

a1

1

9

L

b1 b3 e3 B B3
SIP9

e

c

A

1

0016107 D

6+6W STEREO AMPLIFIER
TDA2007A
ABSOLUTE MAXIMUM RATINGS
Symbol VS IO IO Ptot Tstg, Tj Supply Voltage Output Peak Current (repetitive f 20Hz) Output Peak Current (non repetitive t = 100�s) Power Dissipation at Tcase = 70�C Storage and Junction Temperature 1 Parameter Value 28 3 3.5 0 - 40 to 150 Unit V A A W �C

ELECTRICAL CHARACTERISTICS (refer to the stereo application circuit, Tamb = 25�C, VS = 18V, GV = 36dB, unless otherwise specified)
Symbol VS VO Id PO Parameter Supply Voltage Quiescent Output Voltage Total Quiescent Drain Curent Output Power (each channel) f = 100Hz to 6KHz d = 0.5% VS = 18V RL = 4 VS = 22V RL = 8W f = 1KHz, VS = 18V, RL = 4 PO = 100mW to 3W f = 1KHz, VS = 22V, RL = 8 PO = 100mW to 3W RL = , Rg = 10K f = 1KHz f = 10KHz f = 1KHz RL = 4, C10 = C11 = 2200�F f = 1KHz Rg = 10k ( ) Rg = 10k (oo ) Rg = 10K fripple = 100Hz, Vripple = 0.5V
o

Test Condition

Min. 8

Typ. 8.5 50

Max. 26 90

Unit V V mA

5.5 5.5

6 6 0.1 0.05

W W % %

d

Distortion (each channel)

CT

Cross Talk (

ooo

)

50 40 300 70

60 50 200 40 80 36 0.5 1.5 2.5 55 145 8 36.5

dB dB mV K Hz KHz dB dB �V �V dB �C

Vi Ri fL fH GV GV eN SVR Tj

Input Saturation Voltage (rms) Input Resistance Low Frequency Roll Off (- 3dB) Low Frequency Roll Off (- 3dB) Voltage Gain (closed loop) Closed Loop Gain Matching Total Input Noise Voltage Supply Voltage Rejection (each channel) Thermal Shut-down Junction Temperature
(��) 22Hz to 22KHz.

35.5

(�) Curve A.

PIN CONNECTION (top view)

Power Switching Regulator
STR-G5653
DESCRIPTION
STR-G 5653 is a hybrid IC with a built-in MOS FET and control IC, designed for a primary side regulation. MANY PROTECTION FUNCTIONS OVP(over voltage protection circuit) OCP(over current protection circuit) TSD(Thermal shutdown circuit) BLOCK DIAGRAM

PIN CONFIGURATION

PIN
1 2 3 4 5

SYMBOL
D S GND VIN O.C.P / F.B

Description
Drain Terminal Source Terminal Ground Terminal

Functions
MOS FET DRAIN MOS FET SOURCE GROUND

Power supply Terminal Input of power supply for control circuit over current / Feedback terminal Input of over current detection signal and constant voltage control signals

Full bridge vertical deflection output circuit in LVDMOS
TDA8357J FEATURES
Few external components required High efficiency fully DC coupled vertical bridge output circuit Vertical flyback switch with short rise and fall times Built-in guard circuit Thermal protection circuit Improved EMC performance due to differential inputs.

GENERAL DESCRIPTION
The TDA8357J is a power circuit for use in 90� and 110� colour deflection systems for 25 to 200 Hz field frequencies, and for 4 : 3 and 16 : 9 picture tubes. The IC contains a vertical deflection output circuit, operating as a high efficiency class G system. The full bridge output circuit allows DC coupling of the deflection coil in combination with single positive supply voltages. The IC is constructed in a Low Voltage DMOS (LVDMOS) process that combines bipolar, CMOS and DMOS devices. DMOS transistors are used in the output stage because of absence of second breakdown.

QUICK REFERENCE DATA
SYMBOL Supplies
VP VFB Iq(P)(av) Iq(FB)(av) Ptot supply voltage flyback supply voltage average quiescent supply current average quiescent flyback supply current total power dissipation during scan during scan 7.5 2VP 12 45 10 18 66 15 10 8 V V mA mA W

PARAMETER

CONDITIONS

MIN.

TYP.

MAX.

UNIT

Inputs and outputs
Vi(p-p) Io(p-p) input voltage (peak-to-peak value) output current (peak-to-peak value) 1000 1500 2.0 mV A

Flyback switch
Io(peak) maximum (peak) output current t 1.5 ms 1.2 A

Thermal data; in accordance with IEC 747-1
Tstg Tamb Tj storage temperature ambient temperature junction temperature 55 25 +150 +85 150 �C �C �C

ORDERING INFORMATION
TYPE NUMBER
TDA8357J

PACKAGE NAME
DBS9P

DESCRIPTION
plastic DIL-bent-SIL power package; 9 leads (lead length 12/11 mm); exposed die pad

VERSION
SOT523-1

Full bridge vertical deflection output circuit in LVDMOS
TDA8357J
BLOCK DIAGRAM

TUNER
TECC2949PG35E 1. APPLICATIONS
Reciving System : CCIR Standard system Channel : VHF Low band : NZ1 (45.25MHz) ~ S6 (140.25MHz) VHF High band : S7 (147.25MHz) ~ S36 (423.25MHz) UHF band : S37 (431.25MHz) ~ E69 (855.25MHz)

Intermediate Frequency PIF : ( 38.90 )MHz CIF : ( 34.47 )MHz SIF : ( 33.40 )MHz Input Impedance : UHF/VHF Terminal (75) , Unbalanced Output Impedance : (1)k , Balanced Band Change Over System : (PLL System) Tuning System : (PLL System)

2. RATINGS AND TEST CONDITIONS
Measurement must be executed under the ambient conditions of the room temperature and humidity. (Temp. 25 2 , Humidity 65 5% RH) The following conditions shall be applied for the measurement of electrical characteristics. Voltage & Current at Each Terminal and Operation Guaranteed Voltage SUPPLY VOLTAGE FOR OPERATION BP AGC BT Permissble ripple (note #1) Note #1 : Ripple in the spectrum form 20Hz to 500KHz Temperature Storage Temperature : -20 ~ +70 ~ +65 Operation Temperature : -10 5.0V 5% LIMITED UNIT FOR OPERATION 5.0V 10% CURRENT

110mA Max. -

4.0V Max 0.5V ~ 30V -

4.5V Max 0.5V ~ 33V 5mVp-p Max

TUNER
TERMINAL FOR EXTERNAL CONNECTION

ELECTRICAL CHARACTERISTICS

TUNER
RECEIVING CHANNEL FREQUENCY TABLE

TUNER
RECEIVING CHANNEL FREQUENCY TABLE

TUNER
RECEIVING CHANNEL FREQUENCY TABLE

TV Signal processor- Teletext decoder with embedded -controller
TDA935X/6X/8X PS/N2 Series
General description & features TDA 9361/9381 PS/N2 combine the functions of a TV signal processor together with a -controller and US Closed Caption Decoder. TDA 9361 has a Teletext decoder on board. The Teletext decoder has an internal RAM memory for 10 page text. Multi-standard vision IF circuit with alignment-free PLL demodulator Internal(switchable)time-constant for the IF-AGC circuit A choice can be made between versions with mono intercarrier sound FM demodulator and version with QSS IF amplifier The mono intercarrier sound versions have a selective FM-PLL demodulator which can be switched to the different FM sound frequencies(4.5/5.5/6.0/6.5MHz) The quality of this system is such that the external band-pass filters can be omitted Source selection between `internal' CVBS and external CVBS or Y/C signals Intergrated chrominance trap circuit Intergrated luminance delay line with adjustable delay time Picture improvement features with peaking (with variable centre frequency and positive/negative overshoot ratio)and black stretching Integrated chroma band-pass filter with switchable centre frequency Only one reference(12MHz)crystal required for the -Controller, Teletext and the colour decoder PAL/NTSC or multi-standard colour decoder with automatic search system Internal base-band delay line RGB control circuit with `continuous Cathode Calibration', white point and black level offset adjustment so that the colour temperature of the dark and the light parts of the screen can be chosen independently Linear RGB or YUV input with fast blanking for external RGB/YUV sources The text/OSD signals are internally supplied from the -controller/Teletext decoder Contrast reduction possibility during mixde-mode of OSD and Text signals Horizontal synchronization with two control loops and alignment-free horizontal oscillator Vertical count-down circuit Vertical driver optimized for DC-coupled vertical output stages Low-power start-up of the horizontal drive circuit

SNDIF

RESET

SOUND TRAP SCL SDA +3.3 V VPE VST OUT AUDEXT AUDOUT

LED OUT (2x)

TUNERAGC 10/11 (20) 29 28 (32) 35 1+62-64 DEEMPHASIS ENHANCED 1/10 PAGE MEMORY 80C51 CPU VST PWM-DAC I/O PORTS AUDIO SWITCH (AVL) VOLUME CONTROL I2C-BUS TRANSCEIVER 5-8 (32) 31 60 55 59 58 57 3 4 9 44 2 12 54 56 61

27

37

38

BLOCK DIAGRAM

23

IFIN

24

VISION IF ALIGNMENT-FREE PLL DEMOD. AGC/AFC VIDEO AMP.

ADC IN (4x)

I/O PORTS (4x)

40 CVBS ROM/RAM ACQUISITION V DISPLAY TELETEXT TELETEXT/OSD

VIDEO SWITCH

H

CVBS/Y

42

VIDEO IDENT.

CHROMA 43 SYNC COR R G REF BASE-BAND DELAY LINE LUMA DELAY PEAKING BLACK STRETCH

VIDEO FILTERS

AGC CIRCUIT NARROW BAND PLL DEMODULATOR B BL 51 52 53 WHITE-P. ADJ. R G B H-DRIVE V-DRIVE + V GEOMETRY (EW GEOMETRY) U V 34 16 33 25 26 22 21 36 (20) 46 47 48 45 2nd LOOP H H-SHIFT RGB/YUV INSERT Y RGB/YUV MATRIX SATURATION YUV/RGB MATRIX 49 50

REF

13

CONTR/BRIGHTN OSD/TEXT INSERT CCC

RO GO B0 BCLIN BLKIN

PAL/SECAM/NTSC DECODER (32)

30

41

18

+8V

39

H/V SYNC SEP.

14

H-OSC. + PLL

19

TV Signal processor- Teletext decoder with embedded -controller

15

17

TDA935X/6X/8X PS/N2 Series

HOUT

V-DRIVE

EHTO

EWD

R/V G/Y B/U BL

TV Signal processor- Teletext decoder with embedded -controller
PINNING
SYMBOL
P1.3/T1 P1.6/SCL P1.7/SDA P2.0/TPWN P3.0/ADC0 P3.1/ADC1 P3.2/ADC2 P3.3/ADC3 VSSC/P P0.5 P0.6 VSSA SECPLL VP2 DECDIG PH2LF PH1LF GND3 DECBG AVL/EWD(1) VDRB VDRA IFIN1 IFIN2 IREF VSC TUNERAGC AUDEEM/SIFIN1

TDA935X/6X/8X PS/N2 Series
PIN
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64

DESCRIPTION
Power(ACTINE LOW) ON:LOW, STAND-BT:HIGH Serial CLOCK Serial DATA SVHS MODE DETECTION INPUT(ACTIVE LOW) NTSC SYSTEM CONVERSION OUTPUT(ACTIVE LOW) AUDIO/VIDEO MODE SWITCH 1 CONTROL BUTTON KEY INPUT 1 CONTROL BUTTON KEY INPUT 2 digital ground for -Controller core and periphery AUDIO/VIDEO MODE SWITH 2 Swith Signal Video (status) input analog ground of Teletext decoder and digital ground of TV-Processor SECAM PLL decoupling 2nd supply voltage TV-processor(+8V) decoupling digital supply of TV-processor phase-2 filter phase-1filter ground 3 for TV-processor bandgap decoupling Automatic Volume Levelling/East-West drive output vertical drive B output vertical drive A output IF input 1 IF input 2 reference current input vertical sawtooth capacitor tuner AGC output audio deemphasis of SIF input 1 decoupling sound demodulator of SIF input 2 ground 2 for TV processor narrow band PLL filter/AGC sound IF Automatic Volume Levelling/sound IF input/subcarrier reference output/AM output (non controlled) horizontal output flyback input/sandcastle output external audio input/QSS intercarrier out/AM audio output(non controlled) EHT/overvoltage protection input IF-PLL loop filter IF video output/selected CVBS output main supply voltage TV-processor(+8V) internal CVBS input ground 1 for TV-processor external CVBS/Y input chrominance input (SVHS) audio output /AM audio output(volume controlled) 2nd RGB/YUV insertion input 2nd R input /V(R-Y)input 2nd G input/Y input 2nd B input/U(B-Y)input beam current limiter input/(V-guard input, note 2) black current input/(V-guard input, note2) Red output Green output Blue output analog supply of Teletext decoder and digital suppply of TV-processor(3.3V) OTP Programming Voltage digital supply to core(3.3V) oscillator gorund supply crystal oscillator input crystal oscillator output reset digital supply to periphery(+3.3V) Remote key matrix input 2 I C BUS STOP CONTROL PIN(LOW:BUS STOP) MUTE OUTPUT(ACTIVE HIGH)

TV sound AM-demodulator and audio source switch
TDA9830

TV sound AM-demodulator and audio source switch
TDA9830

TV sound AM-demodulator and audio source switch
TDA9830

Triple Video Output Amplifier
TDA6107Q
GENERAL DESCRIPTION
The TDA6107Q includes three video output amplifiers in one plastic DIL-bent-SIL9-pin medium power(DBS9MPF) package (SOT111-1), using high-voltage DMOS technology, and is intended to drive the three cathodes of a colour CRT directly. To obtain maximum performance, the amplifier should be used with black-current control.

FEATURES
Typical bandwidth of 5.5 MHz for an output signal of 60V (p-p) High slew rate of 900 V/ No external components required Very simple application Single supply voltage of 200 V Internal reference voltage of 2.5V Fixed gain of 50 Black-Current Stabilization (BCS) circuit Thermal protection

BLOCK DIAGRAM
VDD 6 MIRROR 1 MIRROR 5

handbook, full pagewidth

TDA6107Q

CASCODE 1

MIRROR 4 CURRENT SOURCE 1� THERMAL PROTECTION CIRCUIT Vi(1), Vi(2), Vi(3)

3�
1� 9, 8, 7 Voc(3), Voc(2), Voc(1)

Rf VIP REFERENCE DIFFERENTIAL STAGE

1, 2, 3 Ri Ra

MIRROR 3

5

Io(m)

3�

CASCODE 2

MIRROR 2 4
MGK278

Triple Video Output Amplifier
TDA6107Q

SYMBOL PIN Vi(1) Vi(2) Vi(3)
GND Iom VDD Voc(3) Voc(2) Voc(1)

DESCRIPTION incerting input 1 incerting input 2 incerting input 3 ground (fin) black-current measurement output supply voltage cathode output3 cathode output2 cathode output1

1 2 3 4 5 6 7 8 9

TROUBLE SHOOTING
1. NO POWER (The secondary of the SMPS transformer)

START

Check the output voltage of IC52, IC83. Check the cathode voltage of D803. OK? NO Check all the electric leakage in each voltage with multi-meter. OK? NO Fix all the short circuits. Is there low or abnormal voltage nevertheless? YES Check the pin 4 voltage of IC88. Check the waveform between pin 5 and GROUND. Check the voltage of C887. OK? NO Check the short circuits of D881, D882, D883 and D884. Check the open circuits of R882 OK? NO Check F801(fuse). In AC 90-250V INPUT, replace it with 250V 3.15A NO

YES

MAIN PCB IC52 IC83 D803

STAND-BY 3.3V 4.97V 16.2V

ON 3.3V 4.97V 16.2V

MAIN PCB

STAND-BY 32V 1.19V 301V

ON 32V 1.93V 296V

YES

pin 4 of Q801 pin 5 of Q801
C887

END

TROUBLE SHOOTING
2. NO RASTER (The power is normal but the heater voltage is "LOW")

START

Check the voltage between pin 1 of IC51 and GROUND. Is it Low ?

NO

Check the output voltage of IC52, IC83, and IC53. Check the waveform of X001(12MHZ).

YES
HOUT Check the waveform of pin 33 of IC51. OK?
2.5Vpp

YES NO
Check the voltage of C481 + (ST-BY:11.5V, ON:5.9V). Check the open circuit of R481. Check the short circuit of Q402.

Check the BASE waveform of Q404. OK?

YES
Check the COLLECTOR waveform of Q404.

NO
Replace it with new one!

OK? YES

Check the open circuits of R911, R912,D911 in CPT PCB. Is there No Picture?

YES
Replace IC91 with new one. Replace C904 with new one. Check the short circuits of D281. Check the open circuits of R281.

Check the pin 1,2,3 waveforms of IC91 in CPT PCB! Check the pin 7,8,9 waveforms of IC91. Check the pin 6 voltage of IC91.

NO

OK? YES

END

TROUBLE SHOOTING
3. NO PICTURE (SOUND is OK)

START

Check pin 7,8,9 of IC91 in CPT PCB. Check the pin 1,2,3 of IC91. OK? NO Check pin 51,52,53 waveforms of IC51. OK? NO

Check pin 38 waveforms of IC51. Check the pin 40 waveforms of IC51. OK?

NO

Check pin 1,4,5 waveforms of Z101. OK? NO

Check the waveform of IF pin of TU01. OK? YES

NO Replace TU01 with new one.

END

TROUBLE SHOOTING
4. NO SOUND (PICTURE is "OK")

START

See that the sound state is MUTE Check the waveform between pin 9 of IC61 and GROUND. OK?

NO
Check the waveform between pin 1 of IC61 and GROUND See that the mode state (pin 3 of IC62 is HIGH ) (MUTE:LOW, normal:HIGH) OK?

YES Replace IC61 with new one.

NO
FM MONO Check the waveform of Aout at pin 44 of IC51. See that there is no signal in the IF output of TU01, Z101.

END

TROUBLE SHOOTING
5. Vertical Line

START

Check the Supply voltage at pin 3 of IC31 OK? YES

NO V2=DC13.7V Check D382.

Check the waveform at pin 4 & 7 of IC31. OK?

NO

Check the waveform of the posive sawtooth(pin1) and negative sawtooth(pin2) of IC31. YES Check IC31 and Peripheral parts.

OK? NO

Check the waveform at pin 21 and 22 of IC51.

END

BLOCK DIAGRAM

ELECTRICAL PARTS LIST
P / No. A001 A001A AA01U AA01A C020 C057 C060 C061 C067 C161 C162 C182 C512 C519 C521 C522 C533 C536 C546 C547 C548 C550 C569 C591 C592 C593 C608 C623 C644 CN101 CR08 CV51 CV55 CV57 D101 D232 D281 D381 D382 D402 D433 D514 D534 D550 D570 D651 D881 D882 D883 D884 D885 D886 D887 D888 DR01 DR02 DR03 DV51 DV52 DZ181 DZ182 DZ301 DZ801 ITEM No. 150032377 150032378 150130995 150231088 12477104T 12474102T 12474102T 12497223T 12474102T 12497103T 12497103T 12497223T 12497223T 12477104T 12474102T 12474102T 12477104T 12474102T 12477104T 12477104T 12477104T 12474102T 12477104T 12474101T 12474101T 12474101T 12477104T 12474222T 12477104T 12497103T 12474101T 12473680T 12474471T 12474102T 11115024T 11115641T 11115014T 11115014T 11115014T 11115014T 11115638T 11115638T 11115638T 11115635T 11115024T 11115641T 11115464T 11115464T 11115464T 11115464T 11115542T 11115542T 11115542T 11115542T 11115641T 11115641T 11115641T 11115641T 11115641T 11115623T 11115686T 11115651T 11115686T ITEM NAME "MAIN, PAL PTQM03 I10JQ6RST" "MAIN, PAL PTQM03-1 I10JQ6RST" "MAIN, AUTO PTQM03-1 I10JQ6RST" "MAIN, AXIAL PTQM03-1 I10JQ6RST" "CERAMIC CAP, F 50V 0.1MF Z AXIAL" "CERAMIC CAP, B 50V 1000PF K AXIAL" "CERAMIC CAP, B 50V 1000PF K AXIAL" "CERAMIC CAP, F 25V 0.022MF Z AXIAL" "CERAMIC CAP, B 50V 1000PF K AXIAL" "CERAMIC CAP, F 25V 0.01MF Z AXIAL" "CERAMIC CAP, F 25V 0.01MF Z AXIAL" "CERAMIC CAP, F 25V 0.022MF Z AXIAL" "CERAMIC CAP, F 25V 0.022MF Z AXIAL" "CERAMIC CAP, F 50V 0.1MF Z AXIAL" "CERAMIC CAP, B 50V 1000PF K AXIAL" "CERAMIC CAP, B 50V 1000PF K AXIAL" "CERAMIC CAP, F 50V 0.1MF Z AXIAL" "CERAMIC CAP, B 50V 1000PF K AXIAL" "CERAMIC CAP, F 50V 0.1MF Z AXIAL" "CERAMIC CAP, F 50V 0.1MF Z AXIAL" "CERAMIC CAP, F 50V 0.1MF Z AXIAL" "CERAMIC CAP, B 50V 1000PF K AXIAL" "CERAMIC CAP, F 50V 0.1MF Z AXIAL" "CERAMIC CAP, B 50V 100PF K AXIAL" "CERAMIC CAP, B 50V 100PF K AXIAL" "CERAMIC CAP, B 50V 100PF K AXIAL" "CERAMIC CAP, F 50V 0.1MF Z AXIAL" "CERAMIC CAP, B 50V 2200PF K AXIAL" "CERAMIC CAP, F 50V 0.1MF Z AXIAL" "CERAMIC CAP, F 25V 0.01MF Z AXIAL" "CERAMIC CAP, B 50V 100PF K AXIAL" "CERAMIC CAP, SL 50V 68PF J AXIAL" "CERAMIC CAP, B 50V 470PF K AXIAL" "CERAMIC CAP, B 50V 1000PF K AXIAL" "SILICON DIODE, 1N4148" "ZD, MTZJ9.1B (VZ8.57-9.01) 0.5W" "SILICON DIODE, RGP10J" "SILICON DIODE, RGP10J" "SILICON DIODE, RGP10J" "SILICON DIODE, RGP10J" "ZD, MTZJ8.2B (VZ7.78-8.19) 0.5W" "ZD, MTZJ8.2B (VZ7.78-8.19) 0.5W" "ZD, MTZJ8.2B (VZ7.78-8.19) 0.5W" "ZD, MTZJ7.5B (VZ7.07-7.45) 0.5W" "SILICON DIODE, 1N4148" "ZD, MTZJ9.1B (VZ8.57-9.01) 0.5W" "DIODE, RECTIFIER 1N5398E" "DIODE, RECTIFIER 1N5398E" "DIODE, RECTIFIER 1N5398E" "DIODE, RECTIFIER 1N5398E" "DIODE, FAST RECOVERY EU1ZV1" "DIODE, FAST RECOVERY EU1ZV1" "DIODE, FAST RECOVERY EU1ZV1" "DIODE, FAST RECOVERY EU1ZV1" "ZD, MTZJ9.1B (VZ8.57-9.01) 0.5W" "ZD, MTZJ9.1B (VZ8.57-9.01) 0.5W" "ZD, MTZJ9.1B (VZ8.57-9.01) 0.5W" "ZD, MTZJ9.1B (VZ8.57-9.01) 0.5W" "ZD, MTZJ9.1B (VZ8.57-9.01) 0.5W" "ZD, MTZJ5.1B (VZ4.94-5.20) 0.5W" "ZD, MTZJ33B (VZ30.32-31.88) 0.5W" "ZD, MTZJ12B (VZ11.44-12.03) 0.5W" "ZD, MTZJ33B (VZ30.32-31.88) 0.5W" P / No. ITEM No. EL03 11061303 EL04 11061303 EL05 11061303 EL08 11061303 EL11 11061303 EL12 11061303 EL13 11061303 EL14 11061303 EL15 11061303 EL16 11061303 EL19 11061303 EL20 11061303 EL21 11061303 EL22 11061303 EL23 11061303 EL24 11061303 EL25 11061303 EL26 11061303 ES01 11061202 ES03 11061202 ES04 11061202 ES05 11061202 ES06 11061202 ES07 11061202 ES08 11061202 ES09 11061202 ES10 11061202 ES11 11061202 ES12 11061202 ES13 11061202 ES14 11061202 ES16 11061202 ES17 11061202 ES18 11061202 ES19 11061202 ES20 11061202 ES21 11061202 ES22 11061202 ES23 11061202 ES24 11061202 ES25 11061202 ES26 11061202 ES27 11061202 ES28 11061202 ES29 11061202 ES30 11061202 ES31 11061202 J001 11183004 J002 11183004 J003 11183004 J004 11183004 J005 11183004 J006 11183004 J007 11183004 J008 11183004 J009 11183004 J010 11183004 J011 11183004 J012 11183004 J013 11183004 J014 11183004 J015 11183004 J016 11183004 ITEM NAME "EYELET, HTR 2.80*2.9 SNI" "EYELET, HTR 2.80*2.9 SNI" "EYELET, HTR 2.80*2.9 SNI" "EYELET, HTR 2.80*2.9 SNI" "EYELET, HTR 2.80*2.9 SNI" "EYELET, HTR 2.80*2.9 SNI" "EYELET, HTR 2.80*2.9 SNI" "EYELET, HTR 2.80*2.9 SNI" "EYELET, HTR 2.80*2.9 SNI" "EYELET, HTR 2.80*2.9 SNI" "EYELET, HTR 2.80*2.9 SNI" "EYELET, HTR 2.80*2.9 SNI" "EYELET, HTR 2.80*2.9 SNI" "EYELET, HTR 2.80*2.9 SNI" "EYELET, HTR 2.80*2.9 SNI" "EYELET, HTR 2.80*2.9 SNI" "EYELET, HTR 2.80*2.9 SNI" "EYELET, HTR 2.80*2.9 SNI" "EYELET, HTR 2.11*2.8 SNI" "EYELET, HTR 2.11*2.8 SNI" "EYELET, HTR 2.11*2.8 SNI" "EYELET, HTR 2.11*2.8 SNI" "EYELET, HTR 2.11*2.8 SNI" "EYELET, HTR 2.11*2.8 SNI" "EYELET, HTR 2.11*2.8 SNI" "EYELET, HTR 2.11*2.8 SNI" "EYELET, HTR 2.11*2.8 SNI" "EYELET, HTR 2.11*2.8 SNI" "EYELET, HTR 2.11*2.8 SNI" "EYELET, HTR 2.11*2.8 SNI" "EYELET, HTR 2.11*2.8 SNI" "EYELET, HTR 2.11*2.8 SNI" "EYELET, HTR 2.11*2.8 SNI" "EYELET, HTR 2.11*2.8 SNI" "EYELET, HTR 2.11*2.8 SNI" "EYELET, HTR 2.11*2.8 SNI" "EYELET, HTR 2.11*2.8 SNI" "EYELET, HTR 2.11*2.8 SNI" "EYELET, HTR 2.11*2.8 SNI" "EYELET, HTR 2.11*2.8 SNI" "EYELET, HTR 2.11*2.8 SNI" "EYELET, HTR 2.11*2.8 SNI" "EYELET, HTR 2.11*2.8 SNI" "EYELET, HTR 2.11*2.8 SNI" "EYELET, HTR 2.11*2.8 SNI" "EYELET, HTR 2.11*2.8 SNI" "EYELET, HTR 2.11*2.8 SNI" "PLATING WIRE, 0.6MM" "PLATING WIRE, 0.6MM" "PLATING WIRE, 0.6MM" "PLATING WIRE, 0.6MM" "PLATING WIRE, 0.6MM" "PLATING WIRE, 0.6MM" "PLATING WIRE, 0.6MM" "PLATING WIRE, 0.6MM" "PLATING WIRE, 0.6MM" "PLATING WIRE, 0.6MM" "PLATING WIRE, 0.6MM" "PLATING WIRE, 0.6MM" "PLATING WIRE, 0.6MM" "PLATING WIRE, 0.6MM" "PLATING WIRE, 0.6MM" "PLATING WIRE, 0.6MM"

ELECTRICAL PARTS LIST
P / No. J017 J018 J019 J020 J021 J022 J023 J024 J025 J026 J027 J028 J029 J030 J031 J032 J033 J034 J035 J036 J037 J038 J040 J042 J043 J044 J045 J046 J047 J048 J049 J050 J051 J052 J053 J054 J055 J056 J057 J058 J059 J062 J063 J064 J065 J066 J067 J068 J069 J070 J071 J072 J073 J075 J076 J077 J078 J080 J081 J082 J083 J103 J104 ITEM No. 11183004 11183004 11183004 11183004 11183004 11183004 11183004 11183004 11183004 11183004 11183004 11183004 11183004 11183004 11183004 11183004 11183004 11183004 11183004 11183004 11183004 11183004 11183004 11183004 11183004 11183004 11183004 11183004 11183004 11183004 11183004 11183004 11183004 11183004 11183004 11183004 11183004 11183004 11183004 11183004 11183004 11183004 11183004 11183004 11183004 11183004 11183004 11183004 11183004 11183004 11183004 11183004 11183004 11183004 11183004 11183004 11183004 11183004 11183004 11183004 11183004 11183004 11183004 ITEM NAME "PLATING WIRE, 0.6MM" "PLATING WIRE, 0.6MM" "PLATING WIRE, 0.6MM" "PLATING WIRE, 0.6MM" "PLATING WIRE, 0.6MM" "PLATING WIRE, 0.6MM" "PLATING WIRE, 0.6MM" "PLATING WIRE, 0.6MM" "PLATING WIRE, 0.6MM" "PLATING WIRE, 0.6MM" "PLATING WIRE, 0.6MM" "PLATING WIRE, 0.6MM" "PLATING WIRE, 0.6MM" "PLATING WIRE, 0.6MM" "PLATING WIRE, 0.6MM" "PLATING WIRE, 0.6MM" "PLATING WIRE, 0.6MM" "PLATING WIRE, 0.6MM" "PLATING WIRE, 0.6MM" "PLATING WIRE, 0.6MM" "PLATING WIRE, 0.6MM" "PLATING WIRE, 0.6MM" "PLATING WIRE, 0.6MM" "PLATING WIRE, 0.6MM" "PLATING WIRE, 0.6MM" "PLATING WIRE, 0.6MM" "PLATING WIRE, 0.6MM" "PLATING WIRE, 0.6MM" "PLATING WIRE, 0.6MM" "PLATING WIRE, 0.6MM" "PLATING WIRE, 0.6MM" "PLATING WIRE, 0.6MM" "PLATING WIRE, 0.6MM" "PLATING WIRE, 0.6MM" "PLATING WIRE, 0.6MM" "PLATING WIRE, 0.6MM" "PLATING WIRE, 0.6MM" "PLATING WIRE, 0.6MM" "PLATING WIRE, 0.6MM" "PLATING WIRE, 0.6MM" "PLATING WIRE, 0.6MM" "PLATING WIRE, 0.6MM" "PLATING WIRE, 0.6MM" "PLATING WIRE, 0.6MM" "PLATING WIRE, 0.6MM" "PLATING WIRE, 0.6MM" "PLATING WIRE, 0.6MM" "PLATING WIRE, 0.6MM" "PLATING WIRE, 0.6MM" "PLATING WIRE, 0.6MM" "PLATING WIRE, 0.6MM" "PLATING WIRE, 0.6MM" "PLATING WIRE, 0.6MM" "PLATING WIRE, 0.6MM" "PLATING WIRE, 0.6MM" "PLATING WIRE, 0.6MM" "PLATING WIRE, 0.6MM" "PLATING WIRE, 0.6MM" "PLATING WIRE, 0.6MM" "PLATING WIRE, 0.6MM" "PLATING WIRE, 0.6MM" "PLATING WIRE, 0.6MM" "PLATING WIRE, 0.6MM" P / No. ITEM No. J105 11183004 J106 11183004 J111 11183004 J112 11183004 J113 11183004 J114 11183004 L054 11237100T L056 11237100T L061 11237100T L101 11237109T L162 11237100T L201 11237569T L202 11237569T L322 11183004 L323 11183004 L404 11103041T L421 11248331T L623 11103041T L651 11237100T L652 11103041T L802 11103041T L810 11103041T L881 11103041T LV53 11237101T R001 12368101T R002 12368101T R003 12368101T R005 12368101T R007 12368101T R008 12368101T R010 12368513T R011 12368154T R012 12368332T R013 12368472T R014 12368472T R015 12368332T R016 12368332T R017 12368332T R020 12368393T R063 12368101T R064 12368101T R065 12368332T R067 12368332T R101 12368103T R102 12368101T R103 12368104T R104 12368203T R105 12368101T R106 12368101T R107 12368390T R111 12368101T R112 12368101T R161 12368122T R162 12368472T R163 12368471T R164 12368270T R165 12368121T R181 12321390T R182 12321202T R201 12368121T R202 12368121T R203 12368151T R204 12368181T ITEM NAME "PLATING WIRE, 0.6MM" "PLATING WIRE, 0.6MM" "PLATING WIRE, 0.6MM" "PLATING WIRE, 0.6MM" "PLATING WIRE, 0.6MM" "PLATING WIRE, 0.6MM" "COIL, AXIAL LAL02TB 10UH K" "COIL, AXIAL LAL02TB 10UH K" "COIL, AXIAL LAL02TB 10UH K" "COIL, AXIAL LAL02TB 1UH K" "COIL, AXIAL LAL02TB 10UH K" "COIL, AXIAL LAL02TB 5.6UH K" "COIL, AXIAL LAL02TB 5.6UH K" "PLATING WIRE, 0.6MM" "PLATING WIRE, 0.6MM" "B-CORE, BF40 BTL3.5*7B (BFS 3565AO)" "COIL, AXIAL LAL03TB 330UH K" "B-CORE, BF40 BTL3.5*7B (BFS 3565AO)" "COIL, AXIAL LAL02TB 10UH K" "B-CORE, BF40 BTL3.5*7B (BFS 3565AO)" "B-CORE, BF40 BTL3.5*7B (BFS 3565AO)" "B-CORE, BF40 BTL3.5*7B (BFS 3565AO)" "B-CORE, BF40 BTL3.5*7B (BFS 3565AO)" "COIL, AXIAL LAL02TB 100UH J" "CARBON RESISTOR, SB 1/6W 100 OHM J" "CARBON RESISTOR, SB 1/6W 100 OHM J" "CARBON RESISTOR, SB 1/6W 100 OHM J" "CARBON RESISTOR, SB 1/6W 100 OHM J" "CARBON RESISTOR, SB 1/6W 100 OHM J" "CARBON RESISTOR, SB 1/6W 100 OHM J" "CARBON RESISTOR, SB 1/6W 51K OHM J" "CARBON RESISTOR, SB 1/6W 150K OHM J" "CARBON RESISTOR, SB 1/6W 3.3K OHM J" "CARBON RESISTOR, SB 1/6W 4.7K OHM J" "CARBON RESISTOR, SB 1/6W 4.7K OHM J" "CARBON RESISTOR, SB 1/6W 3.3K OHM J" "CARBON RESISTOR, SB 1/6W 3.3K OHM J" "CARBON RESISTOR, SB 1/6W 3.3K OHM J" "CARBON RESISTOR, SB 1/6W 39K OHM J" "CARBON RESISTOR, SB 1/6W 100 OHM J" "CARBON RESISTOR, SB 1/6W 100 OHM J" "CARBON RESISTOR, SB 1/6W 3.3K OHM J" "CARBON RESISTOR, SB 1/6W 3.3K OHM J" "CARBON RESISTOR, SB 1/6W 10K OHM J" "CARBON RESISTOR, SB 1/6W 100 OHM J" "CARBON RESISTOR, SB 1/6W 100K OHM J" "CARBON RESISTOR, SB 1/6W 20K OHM J" "CARBON RESISTOR, SB 1/6W 100 OHM J" "CARBON RESISTOR, SB 1/6W 100 OHM J" "CARBON RESISTOR, SB 1/6W 39 OHM J" "CARBON RESISTOR, SB 1/6W 100 OHM J" "CARBON RESISTOR, SB 1/6W 100 OHM J" "CARBON RESISTOR, SB 1/6W 1.2K OHM J" "CARBON RESISTOR, SB 1/6W 4.7K OHM J" "CARBON RESISTOR, SB 1/6W 470 OHM J" "CARBON RESISTOR, SB 1/6W 27 OHM J" "CARBON RESISTOR, SB 1/6W 120 OHM J" "OXIDE RESISTOR, B 1/2W 39 OHM J" "OXIDE RESISTOR, B 1/2W 2K OHM J" "CARBON RESISTOR, SB 1/6W 120 OHM J" "CARBON RESISTOR, SB 1/6W 120 OHM J" "CARBON RESISTOR, SB 1/6W 150 OHM J" "CARBON RESISTOR, SB 1/6W 180 OHM J"

ELECTRICAL PARTS LIST
P / No. R205 R221 R222 R223 R224 R225 R301 R302 R303 R304 R305 R306 R307 R308 R381 R401 R402 R405 R421 R430 R431 R432 R433 R434 R514 R517 R521 R522 R527 R531 R536 R537 R538 R539 R544 R545 R546 R547 R548 R550 R551 R552 R553 R567 R570 R571 R572 R581 R605 R611 R612 R613 R614 R617 R619 R651 R661 R801 R811 R881 R885 R886 R887 ITEM No. 12368331T 12368153T 12368223T 12368102T 12368220T 12368750T 12328222T 12328222T 12321229T 12368274T 12368123T 12368272T 12321220T 12321331T 12321683T 12368472T 12368101T 12368270T 12321109T 12368102T 12368302T 12368101T 12368183T 12368471T 12368109T 12368153T 12368102T 12368102T 12368681T 12368392T 12368331T 12368391T 12368122T 12368109T 12368822T 12368101T 12368101T 12368101T 12368101T 12368103T 12368101T 12368101T 12368101T 12368104T 12368104T 12368272T 12368243T 12321189T 12368122T 12368390T 12368390T 12368152T 12368202T 12368109T 12368109T 11237100T 12368201T 12321220T 11183004 12919105T 12368472T 12368681T 12977248T ITEM NAME "CARBON RESISTOR, SB 1/6W 330 OHM J" "CARBON RESISTOR, SB 1/6W 15K OHM J" "CARBON RESISTOR, SB 1/6W 22K OHM J" "CARBON RESISTOR, SB 1/6W 1K OHM J" "CARBON RESISTOR, SB 1/6W 22 OHM J" "CARBON RESISTOR, SB 1/6W 75 OHM J" "METAL RESISTOR, K 1/6W 2.2K OHM F" "METAL RESISTOR, K 1/6W 2.2K OHM F" "OXIDE RESISTOR, B 1/2W 2.2 OHM J" "CARBON RESISTOR, SB 1/6W 270K OHM J" "CARBON RESISTOR, SB 1/6W 12K OHM J" "CARBON RESISTOR, SB 1/6W 2.7K OHM J" "OXIDE RESISTOR, B 1/2W 22 OHM J" "OXIDE RESISTOR, B 1/2W 330 OHM J" "OXIDE RESISTOR, B 1/2W 68K OHM J" "CARBON RESISTOR, SB 1/6W 4.7K OHM J" "CARBON RESISTOR, SB 1/6W 100 OHM J" "CARBON RESISTOR, SB 1/6W 27 OHM J" "OXIDE RESISTOR, B 1/2W 1 OHM J" "CARBON RESISTOR, SB 1/6W 1K OHM J" "CARBON RESISTOR, SB 1/6W 3K OHM J" "CARBON RESISTOR, SB 1/6W 100 OHM J" "CARBON RESISTOR, SB 1/6W 18K OHM J" "CARBON RESISTOR, SB 1/6W 470 OHM J" "CARBON RESISTOR, SB 1/6W 1 OHM J" "CARBON RESISTOR, SB 1/6W 15K OHM J" "CARBON RESISTOR, SB 1/6W 1K OHM J" "CARBON RESISTOR, SB 1/6W 1K OHM J" "CARBON RESISTOR, SB 1/6W 680 OHM J" "CARBON RESISTOR, SB 1/6W 3.9K OHM J" "CARBON RESISTOR, SB 1/6W 330 OHM J" "CARBON RESISTOR, SB 1/6W 390 OHM J" "CARBON RESISTOR, SB 1/6W 1.2K OHM J" "CARBON RESISTOR, SB 1/6W 1 OHM J" "CARBON RESISTOR, SB 1/6W 8.2K OHM J" "CARBON RESISTOR, SB 1/6W 100 OHM J" "CARBON RESISTOR, SB 1/6W 100 OHM J" "CARBON RESISTOR, SB 1/6W 100 OHM J" "CARBON RESISTOR, SB 1/6W 100 OHM J" "CARBON RESISTOR, SB 1/6W 10K OHM J" "CARBON RESISTOR, SB 1/6W 100 OHM J" "CARBON RESISTOR, SB 1/6W 100 OHM J" "CARBON RESISTOR, SB 1/6W 100 OHM J" "CARBON RESISTOR, SB 1/6W 100K OHM J" "CARBON RESISTOR, SB 1/6W 100K OHM J" "CARBON RESISTOR, SB 1/6W 2.7K OHM J" "CARBON RESISTOR, SB 1/6W 24K OHM J" "OXIDE RESISTOR, B 1/2W 1.8 OHM J" "CARBON RESISTOR, SB 1/6W 1.2K OHM J" "CARBON RESISTOR, SB 1/6W 39 OHM J" "CARBON RESISTOR, SB 1/6W 39 OHM J" "CARBON RESISTOR, SB 1/6W 1.5K OHMJ" "CARBON RESISTOR, SB 1/6W 2K OHM J" "CARBON RESISTOR, SB 1/6W 1 OHM J" "CARBON RESISTOR, SB 1/6W 1 OHM J" "COIL, AXIAL LAL02TB 10UH K" "CARBON RESISTOR, SB 1/6W 200 OHM J" "OXIDE RESISTOR, B 1/2W 22 OHM J" "PLATING WIRE, 0.6MM" "CARBON RESISTOR, SB 1/2W 1M OHM J" "CARBON RESISTOR, SB 1/6W 4.7K OHM J" "CARBON RESISTOR, SB 1/6W 680 OHM J" "RES, NKN1WSJT-52 0R24 OHM (PRN)" P / No. ITEM No. R890 12005475T R891 12005475T R930 12321109T RN05 12368103T RN06 12368472T RN07 12368472T RR01 12368750T RR02 12368750T RR03 12368750T RR06 12368102T RR07 12368750T RR08 12368102T RS10 12368332T RS11 12368101T RV51 12368750T RV52 12368102T RV53 12368102T RV61 12368102T RV62 12368471T RV63 12368221T RV64 12368302T U111 11893282 C056 12793101T C058 12353220T C059 12353220T C063 12793101T C081 12793221T C101 12794100T C181 12793471T C183 12797100T C221 12794101T C301 12692473T C302 12692473T C303 12693473T C382 12692104T C383 12795221T C384 12692104T C402 12692333T C421 12797330T C430 12692473T C481 12794470T C511 12692224T C513 12793101T C514 12797229T C515 12692222T C516 12692222T C517 12797109T C518 12797100T C520 12797109T C527 12692332T C528 12692103T C529 12797100T C531 12692122T C532 12436331T C535 12797229T C537 12692104T C539 12793101T C540 12692473T C544 12692473T C549 12797339T C581 12683471T C582 12683471T C605 12692103T ITEM NAME "SURGE RES(VDE),1/2W 4.7M OHM" "SURGE RES(VDE),1/2W 4.7M OHM" "OXIDE RESISTOR, B 1/2W 1 OHM J" "CARBON RESISTOR, SB 1/6W 10K OHM J" "CARBON RESISTOR, SB 1/6W 4.7K OHM J" "CARBON RESISTOR, SB 1/6W 4.7K OHM J" "CARBON RESISTOR, SB 1/6W 75 OHM J" "CARBON RESISTOR, SB 1/6W 75 OHM J" "CARBON RESISTOR, SB 1/6W 75 OHM J" "CARBON RESISTOR, SB 1/6W 1K OHM J" "CARBON RESISTOR, SB 1/6W 75 OHM J" "CARBON RESISTOR, SB 1/6W 1K OHM J" "CARBON RESISTOR, SB 1/6W 3.3K OHM J" "CARBON RESISTOR, SB 1/6W 100 OHM J" "CARBON RESISTOR, SB 1/6W 75 OHM J" "CARBON RESISTOR, SB 1/6W 1K OHM J" "CARBON RESISTOR, SB 1/6W 1K OHM J" "CARBON RESISTOR, SB 1/6W 1K OHM J" "CARBON RESISTOR, SB 1/6W 470 OHM J" "CARBON RESISTOR, SB 1/6W 220 OHM J" "CARBON RESISTOR, SB 1/6W 3K OHM J" "PCB, MAIN PTQM03 FR-1" "CHEMICON, 10V 100MF 85C 5*11" "CERAMIC CAPACITOR, CH 50V 22PF J" "CERAMIC CAPACITOR, CH 50V 22PF J" "CHEMICON, 10V 100MF 85C 5*11" "CHEMICON, 10V 220MF 85C 6.3*11" "CHEMICON, 16V 10MF 85C 5*11" "CHEMICON, 10V 470MF 85C 8*12" "CHEMICON, 50V 10MF 85C 5*11" "CHEMICON, 16V 100MF 85C 6.3*11" "PLASTIC CAPACITOR, M 50V 0.047MF J" "PLASTIC CAPACITOR, M 50V 0.047MF J" "PLASTIC CAPACITOR,M 100V 0.047MF J" "PLASTIC CAPACITOR, M 50V 0.1MF J" "CHEMICON, 25V 220MF 85C 8*12" "PLASTIC CAPACITOR, M 50V 0.1MF J" "PLASTIC CAPACITOR, M 50V 0.033MF J" "CHEMICON, 50V 33MF 85C 6.3*11" "PLASTIC CAPACITOR, M 50V 0.047MF J" "CHEMICON, 16V 47MF 85C 5*11" "PLASTIC CAPACITOR, M 50V 0.22MF J" "CHEMICON, 10V 100MF 85C 5*11" "CHEMICON, 50V 2.2MF 85C 5*11" "PLASTIC CAPACITOR, M 50V 2200PF J" "PLASTIC CAPACITOR, M 50V 2200PF J" "CHEMICON, 50V 1MF 85C 5*11" "CHEMICON, 50V 10MF 85C 5*11" "CHEMICON, 50V 1MF 85C 5*11" "PLASTIC CAPACITOR, M 50V 3300PF J" "PLASTIC CAPACITOR, M 50V 0.01MF J" "CHEMICON, 50V 10MF 85C 5*11" "PLASTIC CAPACITOR, M 50V 1200PF J" "CERAMIC CAPACITOR, SL 50V 330PF J" "CHEMICON, 50V 2.2MF 85C 5*11" "PLASTIC CAPACITOR, M 50V 0.1MF J" "CHEMICON, 10V 100MF 85C 5*11" "PLASTIC CAPACITOR, M 50V 0.047MF J" "PLASTIC CAPACITOR, M 50V 0.047MF J" "CHEMICON, 50V 3.3MF 85C 5*11" "CHEMICON, 16V 470MF SHL,SD (8*11.5)" "CHEMICON, 16V 470MF SHL,SD (8*11.5)" "PLASTIC CAPACITOR, M 50V 0.01MF J"

ELECTRICAL PARTS LIST
P / No. C609 C611 C612 C613 C614 C615 C617 C619 C620 C622 C677 C805 C889 C890 C891 CV31 L405 Q161 Q201 Q202 Q221 Q402 Q601 QN01 QN11 QN12 QV61 X102 X103 Z201 Z202 Z203 C021 C281 C381 C403 C411 C412 C422 C801 C820 C821 C880 C881 C883 C885 C886 C887 C887 C888 C892 C893 C894 C895 C896 C899 D801 D802 D803 D803A D803B D803C D822 ITEM No. 12794471T 12797229T 12794221T 12797220T 12794221T 12797229T 12692104T 12692104T 12794101T 12794471T 12797109T 12793471T 12797470T 12436471T 12212102T 12794100T 11261021T 11114066T 11114045T 11114045T 11114119T 11114225T 11114056T 11114056T 11114045T 11114119T 11114056T 11107241T 11107241T 11107135T 11107031T 11107013T 12828104B 12700100T 12797331T 12796331T 12834823B 12820103B 12085049S 12703222S 12796331T 12796331T 12095206B 12094210T 12094210T 12095247C 12095246C 12086026 C2086026 12094216T 12820103B 12094123A 12094123A 12794222T 12095206B 12094123A 11115753 11115753 11115748 11865889 11032381 11971010 11115584 ITEM NAME "CHEMICON, 16V 470MF 85C 10*13" "CHEMICON, 50V 2.2MF 85C 5*11" "CHEMICON, 16V 220MF 85C 8*12" "CHEMICON, 50V 22MF 85C 5*11" "CHEMICON, 16V 220MF 85C 8*12" "CHEMICON, 50V 2.2MF 85C 5*11" "PLASTIC CAPACITOR, M 50V 0.1MF J" "PLASTIC CAPACITOR, M 50V 0.1MF J" "CHEMICON, 16V 100MF 85C 6.3*11" "CHEMICON, 16V 470MF 85C 10*13" "CHEMICON, 50V 1MF 85C 5*11" "CHEMICON, 10V 470MF 85C 8*12" "CHEMICON, 50V 47MF 85C 6.3*11" "CERAMIC CAPACITOR, SL 50V 470PF J" "CERAMIC CAPACITOR, B 50V 1000PF K" "CHEMICON, 16V 10MF 85C 5*11" "COIL, ELC0607RA-1R0K (KRF9229)" "TR, KTC388A-TM (KTC3197)" "TR, KTA562TM-Y (KTA1270-Y)" "TR, KTA562TM-Y (KTA1270-Y)" "TR, KTC200-Y" "TR, KTC2383-Y (KTC3228-Y)" "TR, KTC1815-Y (KTC3198-Y)" "TR, KTC1815-Y (KTC3198-Y)" "TR, KTA562TM-Y (KTA1270-Y)" "TR, KTC200-Y" "TR, KTC1815-Y (KTC3198-Y)" "C/TRAP, MKTG40M4AAHP00A03 MURATA" "C/TRAP, MKTG40M4AAHP00A03 MURATA" "C/TRAP,TPSRA6M50B00-A0 (MURATA)" "C/TRAP,TPSRA5M50B00-A0( MURATA)" "C/TRAP,TPSRA4M50C00-A0( MURATA)" "P/ CAP, T 200V 0.1MF J PFU" "CHEMICON, 250V 10MF SMS,SG (10*20" "CHEMICON, 50V 330MF 85C 10*20" "CHEMICON, 35V 330MF 85C 10*16" "P/ CAP, T 400V 0.082MF K PFU" "P/ CAP, T 630V 0.01MF J" "CHEMICON,KSA 105C 50V 4.7UF 16*35.5" "CHEMICON, 35V 2200MF KMG,RD 16*25" "CHEMICON, 35V 330MF 85C 10*16" "CHEMICON, 35V 330MF 85C 10*16" "CERA-CAPA, DA2GYB102MK617 NK" "CERA-CAPA, DM3DYB222K725 (2KV2200)" "CERA-CAPA, DM3DYB222K725 (2KV2200)" "PLASTIC CAP, LE-334C AC275V0.33MF K" "PLASTIC CAP,LE-224C AC275V 0.22MF K" "CHEMICON, HC 400V 150MF(22*35)" "CHEMI CON, 69W 400V 150MF(22*35)" "CERA-CAPA, DG3DHR471K825 (2KV470)" "P/ CAP, T 630V 0.01MF J" "CERA-CAPA, AC400V B 470PF K AD" "CERA-CAPA, AC400V B 470PF K AD" "CHEMICON, 16V 2200MF 85C 13*25" "CERA-CAPA, DA2GYB102MK617 NK" "CERA-CAPA, AC400V B 470PF K AD" "DIODE, RK-46(LF015-304) SANKEN" "DIODE, RK-46(LF015-304) SANKEN" "DIODE, UFR FML22S" HEAT SINK 10GN "SCREW, TTB 3*8 SZN" "COMPOUND SILICON, YG6260" "DIODE, FAST-RECTI RU4YX(LF015-304)" P / No. ITEM No. ITEM NAME D823 11115748 "DIODE, UFR FML22S" D823A 11865602 "HEAT SINK, 20LX (45MM)" D823B 11032381 "SCREW, TTB 3*8 SZN" D823C 11971010 "COMPOUND SILICON, YG6260" F801 11144204 "FUSE,250V T3.15A 218 K/S/V/R/B/T/C" F801A 11165037T "HOLDER, FUSE 5.2 (TAPPING)" IC01 11118502 "IC, EEPROM-8K AT24C08A-10PI-2.7" IC01 11118078A "IC, EEPROM-8K M24C08-10PC (8P3)" IC01 11118502 "IC, EEPROM-8K AT24C08A-10PI-2.7" IC31 11118507 "IC, VERTICAL OUT TDA8357J/N2" IC31A 11865887 "HEAT SINK, 10GN (60MM)" IC31B 11032381 "SCREW, TTB 3*8 SZN" IC31C 11971010 "COMPOUND SILICON, YG6260" IC51 11118468 IC. UOC TDA9361PS/N2/5I (OTP/128K) IC52 11118370A "IC, KIA78R33API 1A/3.3V PIN4 KEC" IC53 11118426 "IC, KIA78R08API 1A/8V 4PIN KEC" IC61 11119585 "IC, TDA2007A (SIP9) AUDIO(6+6W) STM" IC83 11119282 "IC, REGU. 1[A] KIA7805PI(7805API)" IC88 11118487 IC SMPS STR-G5653 (LF1129) IC88A 11865673 "HEAT SINK, 14LM" IC88B 11032381 "SCREW, TTB 3*8 SZN" IC88C 11971010 "COMPOUND SILICON, YG6260" JD81 11163079A "JACK, DC TC18-013-12" JD81A 11865460 "BRACKET, DC JACK" JV201 11163084A "SOCKET, RGB 21P(SCART JACK)" JW01 3100015AG "WIRE, UL1007 AWG24 BLU 150MM(5-5)" L422 11222001 "COIL, LIN KLN2035 4.8UH (DR 8*11)" N101 11961024 "SOLDER WIRE, ENERGIZED 63SN 1.2MM" N102 11961013 "SOLDER BAR, 63SN S63S" N102 11961025 "SOLDER WIRE, 63SN 3.0MM" N103 11964033 "SOLVENT, IPA4520" N104 11961020 "FLUX, JS-64T-3" P001 11164122 "PLUG, 3P 5267-03AX" P002 11164123 "PLUG, 4P 5267-04AX" P401 11164391 "PLUG, YFW500-04" P501A 11164125 "PLUG, 6P 5267-06AX" P501B 11164122 "PLUG, 3P 5267-03AX" P601 11164122 "PLUG, 3P 5267-03AX" P661 11164121 "PLUG, 2P 5267-02AX" P801A 11164034 "PLUG, 2P LARGE 5289-2A 7.5MM" P802A 11164034 "PLUG, 2P LARGE 5289-2A 7.5MM" P803A 11164034 "PLUG, 2P LARGE 5289-2A 7.5MM" P890 11164123 "PLUG, 4P 5267-04AX" P891 11116335 "WAFER, 2P YDW236-02W" P892 11164654 "PLUG, YW396-03AV" PF001 11164124 "PLUG, 5P 5267-05AX" PT01 11160001 "TERMINAL, PIN R93-31" PT02 11160001 "TERMINAL, PIN R93-31" Q404 11114223 "TR, HORIZONTAL BU406TU (TO-220) FSC" Q404A 11865889 HEAT SINK 10GN Q404B 11032382 "SCREW, TTB 3*10 SZN" Q404C 11971010 "COMPOUND SILICON, YG6260" R481 12323470S "OXIDE RESISTOR, B 2W 47 OHM J" R608 12322109S "OXIDE RESISTOR, B 1W 1 OHM J" R882 12007046 "CEMENT RES, RWR 5W 1 OHM J PL" R883 12323224S "OXIDE RESISTOR, B 2W 220K OHM J" R884 12322220S "OXIDE RESISTOR, B 1W 22 OHM J" R892 12323823S "OXIDE RESISTOR, B 2W 82K OHM J" S801 11145253A "S/W,JPP-1197B-3" T401 11224037 "TRANS, H.D.T KLN-2023" T461 11226246B "FBT, MCK-10A004 10JQ" T881 11211049 "COIL, LINEFILTER KRF-3026" T881 11211049A "COIL, LINEFILTER KRF-3026"

ELECTRICAL PARTS LIST
P / No. T882 TU01 TU01 X001 Z101 Z101 A001B AB01U AB01A D901 D902 D903 D907 D908 D909 D910 D911 D917 D918 D919 D992 DZ901 DZ902 EL06 EL10 EL17 EL18 J901 J902 J903 J904 J905 J906 J907 J908 J909 J910 J911 N201A N201B R901 R902 R903 R907 R908 R909 R910 R917 R918 R919 R931 R992 C992 L901 SG001 SG002 SG003 SG004 C901 C902 C903 C904 C991 ITEM No. 11213401A 11121229A 11121238 11153025A 11107144 11107220 150032379 150130996 150231089 11115024T 11115024T 11115024T 11115710T 11115710T 11115710T 11115003T 11115444T 11115710T 11115710T 11115710T 11115444T 11115635T 11115651T 11061303 11061303 11061303 11061303 11183004 11183004 11183004 11183004 11183004 11183004 11183004 11183004 11183004 11183004 11183004 11965057 11965058 12368101T 12368101T 12368101T 12368101T 12368101T 12368101T 12919225T 12919152T 12919152T 12919152T 12368102T 12368103T 12797100T 11261020T 11140027T 11140027T 11140027T 11140027T 12700479T 12095062T 12700479T 12094210T 12095133B ITEM NAME "TRANS, SMPS KPW-1180 10GN" "TUNER, TECC2949PG35F IIC DIN" "TUNER, TAEM-G104D" "CRYSTAL, 12.000000MHZ 16PF-FD HC 13" "SAW FILTER, OFWK2950M (SIEMENS)" "SAW FILTER, K2955M (BG/DK) SIP5K" "CRT, PAL PTQM03-2 I10JQ6RST" "CRT, AUTO PTQM03-2 I10JQ6RST" "CRT, AXIAL PTQM03-2 I10JQ6RST" "SILICON DIODE, 1N4148" "SILICON DIODE, 1N4148" "SILICON DIODE, 1N4148" "DIODE, BAV21 (AMMO-52MM) PHILIPS" "DIODE, BAV21 (AMMO-52MM) PHILIPS" "DIODE, BAV21 (AMMO-52MM) PHILIPS" "SILICON DIODE, 1N4004" "DIODE, RGP15J" "DIODE, BAV21 (AMMO-52MM) PHILIPS" "DIODE, BAV21 (AMMO-52MM) PHILIPS" "DIODE, BAV21 (AMMO-52MM) PHILIPS" "DIODE, RGP15J" "ZD, MTZJ7.5B (VZ7.07-7.45) 0.5W" "ZD, MTZJ12B (VZ11.44-12.03) 0.5W" "EYELET, HTR 2.80*2.9 SNI" "EYELET, HTR 2.80*2.9 SNI" "EYELET, HTR 2.80*2.9 SNI" "EYELET, HTR 2.80*2.9 SNI" "PLATING WIRE, 0.6MM" "PLATING WIRE, 0.6MM" "PLATING WIRE, 0.6MM" "PLATING WIRE, 0.6MM" "PLATING WIRE, 0.6MM" "PLATING WIRE, 0.6MM" "PLATING WIRE, 0.6MM" "PLATING WIRE, 0.6MM" "PLATING WIRE, 0.6MM" "PLATING WIRE, 0.6MM" "PLATING WIRE, 0.6MM" "TAPE, YW-5006 6.2MM*2000M ROLL" "TAPE, TESAKREPP-4387 6.0MM*2000M" "CARBON RESISTOR, SB 1/6W 100 OHM J" "CARBON RESISTOR, SB 1/6W 100 OHM J" "CARBON RESISTOR, SB 1/6W 100 OHM J" "CARBON RESISTOR, SB 1/6W 100 OHM J" "CARBON RESISTOR, SB 1/6W 100 OHM J" "CARBON RESISTOR, SB 1/6W 100 OHM J" "CARBON RESISTOR, SB 1/2W 2.2M OHM J" "CARBON RESISTOR, SB 1/2W 1.5K OHM J" "CARBON RESISTOR, SB 1/2W 1.5K OHM J" "CARBON RESISTOR, SB 1/2W 1.5K OHM J" "CARBON RESISTOR, SB 1/6W 1K OHM J" "CARBON RESISTOR, SB 1/6W 10K OHM J" "CHEMICON, 50V 10MF 85C 5*11" "COIL, ELC0607RA-180K(KRF9200)" "SPARK GAP, 1.5KV SSG-152-A1" "SPARK GAP, 1.5KV SSG-152-A1" "SPARK GAP, 1.5KV SSG-152-A1" "SPARK GAP, 1.5KV SSG-152-A1" "CHEMICON, 250V 4.7MF SMS,SG (10*13" "P/ CAP, 250V 0.1MF J TNU" "CHEMICON, 250V 4.7MF SMS,SG (10*13" "CERA-CAPA, DM3DYB222K725 (2KV2200)" "P/ CAP, 250V 4.4MF TNU" P / No. ITEM No. ITEM NAME C993 12794102T "CHEMICON, 16V 1000MF 85C 10*20" D991 11114647 THYRISTOR TF361M H501 300924032B"HARNESS,9P (320MM)" IC91 11118138B "IC, VIDEO AMP TDA6107JF/N3 PHILIPS" IC91A 11865543 "HEAT SINK,(PLATE) (30MM)" IC91B 11032381 "SCREW, TTB 3*8 SZN" IC91C 11971010 "COMPOUND SILICON, YG6260" JW91 300104125J "HARNESS, 1P 250MM" P991 11164595 "PLUG, 2P YPW500-2" R911 12323120S "OXIDE RESISTOR, B 2W 12 OHM J" R912 12323120S "OXIDE RESISTOR, B 2W 12 OHM J" R990 12323153S "OXIDE RESISTOR, B 2W 15K OHM J" R991 12323183S "OXIDE RESISTOR, B 2W 18K OHM J" R993 12323123S "OXIDE RESISTOR, B 2W 12K OHM J" R994 12323153S "OXIDE RESISTOR, B 2W 15K OHM J" V901A 11116392 "SOCKET CRT, PCS633A 14" 28MM" V901A C1116392 "SOCKET CRT, GZS8-6-FD(14) 28MM" A001C 150032380 "CONTROL, PAL PTQM03-3 I10JQ6RST" AC01U 150130997 "CONTROL, AUTO PTQM03-3 I10JQ6RST" AC01A 150231090 "CONTROL, AXIAL PTQM03-3 I10JQ6RST" RC01 12368102T "CARBON RESISTOR, SB 1/6W 1K OHM J" RC02 12368162T "CARBON RESISTOR, SB 1/6W 1.6K OHM J" RC03 12368242T "CARBON RESISTOR, SB 1/6W 2.4K OHM J" RC04 12368102T "CARBON RESISTOR, SB 1/6W 1K OHM J" SC01 11145067T "SWITCH, TACT KPT-1115AM(TAP)" SC02 11145067T "SWITCH, TACT KPT-1115AM(TAP)" SC03 11145067T "SWITCH, TACT KPT-1115AM(TAP)" SC04 11145067T "SWITCH, TACT KPT-1115AM(TAP)" SC05 11145067T "SWITCH, TACT KPT-1115AM(TAP)" SC06 11145067T "SWITCH, TACT KPT-1115AM(TAP)" M001 300322925A"HARNESS, 3P 250MM (5264-35022)" A001D 150032381 "MODULE, PAL PTQM03-4 I10JQ6RST" AD01U 150130998 "MODULE, AUTO PTQM03-4 I10JQ6RST" AD01A 150231091 "MODULE, AXIAL PTQM03-4 I10JQ6RST" CM002 12477473T "CERAMIC CAP, F 50V 0.047MF Z AXIAL" RL001 12368561T "CARBON RESISTOR, SB 1/6W 560 OHM J" RM001 12368101T "CARBON RESISTOR, SB 1/6W 100 OHM J" RM002 12368109T "CARBON RESISTOR, SB 1/6W 1 OHM J" CM001 12793101T "CHEMICON, 10V 100MF 85C 5*11" QL001 11114056T "TR, KTC1815-Y (KTC3198-Y)" DL01 11113005 "LED, SLR114 RED�'5 DIFF. STOPPER" M002 300424025I "HARNESS, 4P 250MM (5264-5395)" ZM001 11132044 "RX MODULE, ROM-N338THC" A001E 150032382 "E/JACK, PAL PTQM03-5 I10JQ6RST" AE01A 150231092 "E/JACK, AXIAL PTQM03-5 I10JQ6RST" M662 300324025A"HARNESS, 3P 250MM (5264-5395)" P662 11163129 "E/JACK, TC38-035-01-T (THREAD+NUT)" A002 150032383 "SECAM, PAL PTQZ05 I10JQ6RST" A002U 150130999 "SECAM, AUTO PTQZ05 I10JQ6RST" A002A 150231093 "SECAM, AXIAL PTQZ05 I10JQ6RST" CS01 12497103T "CERAMIC CAP, F 25V 0.01MF Z AXIAL" CS13 12497103T "CERAMIC CAP, F 25V 0.01MF Z AXIAL" JS01 11183004 "PLATING WIRE, 0.6MM" JS02 11183004 "PLATING WIRE, 0.6MM" JS03 11183004 "PLATING WIRE, 0.6MM" JS04 11183004 "PLATING WIRE, 0.6MM" JS05 11183004 "PLATING WIRE, 0.6MM" RS05 12368104T "CARBON RESISTOR, SB 1/6W 100K OHM J" RS06 12368203T "CARBON RESISTOR, SB 1/6W 20K OHM J" RS07 12368132T "CARBON RESISTOR, SB 1/6W 1.3K OHMJ" RS08 12368181T "CARBON RESISTOR, SB 1/6W 180 OHM J" RS09 12368112T "CARBON RESISTOR, SB 1/6W 1.1K OHMJ" U112 11893283A "PCB, SECAM PTQZ05 FR-1"

ELECTRICAL PARTS LIST
P / No. CS03 CS04 CS06 CS07 CS08 CS09 CS14 QS01 ICS01 JW02 N201 N202 N202 N203 N204 PS02 ZS01 A003 A003U A003A C808 C810 D805 D806 EL81 EL82 EL83 EL84 EL85 EL86 EL87 EL88 ES81 ES82 ES83 ES84 J801 J802 J803 J804 J805 J806 R811 R812 U113 C802 C803 C806 C807 Q801 Q802 B801A B801B IC81 IC81A IC81B IC81C IC82 IC82A IC82B IC82C L801 L802 ITEM No. ITEM NAME 12797479T "CHEMICON, 50V 4.7MF 85C 5*11" 12797479T "CHEMICON, 50V 4.7MF 85C 5*11" 12692224T "PLASTIC CAPACITOR, M 50V 0.22MF J" 12692104T "PLASTIC CAPACITOR, M 50V 0.1MF J" 12797100T "CHEMICON, 50V