Sony CDP-XE400.pdf part of SONY CDP-XE400 CDP- XE500 Sony CDP-XE400.pdf, SONY CDP-XE400 CDP-XE500 text manual preview

Text preview for : Sony CDP-XE400.pdf part of SONY CDP-XE400 CDP- XE500 SONY CDP-XE400 CDP-XE500

Back to : Sony CDP-XE400.pdf | Home

CDP-XE400/XE500
SERVICE MANUAL
US Model
CDP-XE400/XE500

AEP Model UK Model E Model Australian Model Chinese Model
CDP-XE500

Photo: CDP-XE500

Model Name Using Similar Mechanism CD Mechanism Type Base Unit Name

CDP-261/361 CDM14-5BD20 BU-5BD20

SPECIFICATIONS

COMPACT DISC PLAYER
MICROFILM

1

The laser component in this product

SAFETY CHECK-OUT
After correcting the original service problem, perform the following safety check before releasing the set to the customer: Check the antenna terminals, metal trim, "metallized" knobs, screws, and all other exposed metal parts for AC leakage. Check leakage as described below. LEAKAGE TEST The AC leakage from any exposed metal part to earth ground and from all exposed metal parts to any exposed metal part having a return to chassis, must not exceed 0.5 mA (500 microampers). Leakage current can be measured by any one of three methods. This appliance is classified as a CLASS 1 LASER product. The CLASS 1 LASER PRODUCT MARKING is located on the rear exterior. 1. A commercial leakage tester, such as the Simpson 229 or RCA WT-540A. Follow the manufacturers' instructions to use these instruments. 2. A battery-operated AC milliammeter. The Data Precision 245 digital multimeter is suitable for this job. 3. Measuring the voltage drop across a resistor by means of a VOM or battery-operated AC voltmeter. The "limit" indication is 0.75 V, so analog meters must have an accurate low-voltage scale. The Simpson 250 and Sanwa SH-63Trd are examples of a passive VOM that is suitable. Nearly all battery operated digital multimeters that have a 2V AC range are suitable. (See Fig. A)

is capable of emitting radiation exceeding the limit for Class 1.

The following caution label is located inside of the unit.

CAUTION
Use of controls or adjustments or performance of procedures other than those specified herein may result in hazardous radiation exposure.

Notes on Chip Component Replacement · Never reuse a disconnected chip component. · Notice that the minus side of a tantalum capacitor may be damaged by heat.

To Exposed Metal Parts on Set

MODEL IDENTIFICATION
0.15µF 1.5k

Back Panel

AC voltmeter (0.75V)

Earth Ground

Fig. A. Using an AC voltmeter to check AC leakage.

CDP-XE400 US Model CDP-XE500 US Model E Model Australian Model Chinese Model AEP, German, East European Model UK Model

: 4-977-587-5 : 4-977-587-1 : 4-977-587-3 : 4-977-587-4 : 4-977-587-9 : 4-978-388-0 : 4-978-388-1

2

NOTES ON HANDLING THE OPTICAL PICK-UP BLOCK OR BASE UNIT The laser diode in the optical pick-up block may suffer electrostatic breakdown because of the potential difference generated by the charged electrostatic load, etc. on clothing and the human body. During repair, pay attention to electrostatic breakdown and also use the procedure in the printed matter which is included in the repair parts. The flexible board is easily damaged and should be handled with care. NOTES ON LASER DIODE EMISSION CHECK The laser beam on this model is concentrated so as to be focused on the disc reflective surface by the objective lens in the optical pick-up block. Therefore, when checking the laser diode emission, observe from more than 30 cm away from the objective lens. LASER DIODE AND FOCUS SEARCH OPERATION CHECK 1. Make POWER switch on with no disc inserted and disc table closed. 2. Confirm that the following operation is performed while observing the objective lens.

TABLE OF CONTENTS 1. GENERAL
Identifying the Parts .................................................................. 4 Playing a CD .............................................................................. 5

2. DISASSEMBLY
2-1. Front Panel .............................................................................. 6 2-2. Base Unit Block ...................................................................... 6

3. ELECTRICAL BLOCK CHECKING ............................. 7 4. DIAGRAMS
4-1. IC Pin Functions ...................................................................... 9 4-2. Printed Wiring Board BD Section ................................... 13 4-3. Schematic Diagram BD Section ...................................... 15 4-4. Printed Wiring Boards Main Section .............................. 17 4-5. Schematic Diagram Main Section ................................... 21

5. EXPLODED VIEWS
5-1. Case Section .......................................................................... 5-2. Back Panel Section ................................................................ 5-3. CD Mechanism Section ......................................................... 5-4. Base Unit Section .................................................................. 28 29 30 31

6. ELECTRICAL PARTS LIST .......................................... 32

SAFETY-RELATED COMPONENT WARNING!! COMPONENTS IDENTIFIED BY MARK ! OR DOTTED LINE WITH MARK ! ON THE SCHEMATIC DIAGRAMS AND IN THE PARTS LIST ARE CRITICAL TO SAFE OPERATION. REPLACE THESE COMPONENTS WITH SONY PARTS WHOSE PART NUMBERS APPEAR AS SHOWN IN THIS MANUAL OR IN SUPPLEMENTS PUBLISHED BY SONY.

3

IDENTIFYING THE PARTS
Front Panel/Remote Commander

1

2

3 4

5

6

7

8 90

!¡

· · · · · · · · · ·

· ·

· · · · · ·

!ª

!· !¶

!§

!

!¢ !£

!TM

SECTION 1 GENERAL

4
· · !¢ · · · · 9 8 @ !£

RM-D420 (CDP-XE500 only)

1 2 3 4 5 6 7 8 9 0 !¡ !TM !£ !¢ ! !§ !¶ !· !ª @º

@º

@¡

·

@TM @£ 3 ! @¢

· ·

@¡ @TM @£ @¢ @

POWER switch PLAY MODE button REPEAT button TIME button Disc tray § OPEN/CLOSE button 0/) (manual search) button CHECK (program check) button CLEAR (program clear) button ENTER button AMS ± (AMS*) control PHONES Jack p (Stop) button P (Pause) button · (Play) button Display MUSIC SCAN button PEAK SEARCH button EDIT/TIME button Play Mode buttons CONTINUE button SHUFFLE button PROGRAM button Numeric buttons >10 (over 10) button TIME button =/+ (AMS*) button FADER button *AMS is the abbreviation of Automatic Music Sensor.

7

5

SECTION 2 DISASSEMBLY
Note : Follow the disassembly procedure in the numerical order given.

2-1. FRONT PANEL
· When removing the front panel assembly on electric power failure, first open the loading block by turning cam with a screwdriver as shown in the figure, next pull out the loading block with hand, and remove the loading panel as shown in the figure, then remove the front panel assembly.
3 Remove loading panel in the arrow direction.

bottom of chassis
1Turn in the direction of the arrow.

2 Pull out disc table.

2-2. BASE UNIT BLOCK
1 Turn the cam to direction of arrow (Counter clockwise) by minus screw driver. 2 Take off the disc table. 3 Remove the yoke bracket. 4 Remove the MD (BU-5BD20) to the direction of arrow.

4 BU-5BD20

3 yoke bracket

1 cam

2 disc table

6

SECTION 3 ELECTRICAL BLOCK CHECKING
Note : 1. CD Block is basically designed to operate without adjustment. Therefore, check each item in order given. 2. Use YEDS-18 disc (3-702-101-01) unless otherwise indicated. 3. Use an oscilloscope with more than 10M impedance. 4. Clean the objective lens using an applicator with neutral detergent when the signal level is low than specified value with the following checks. S Curve Check
oscilloscope BD board TP (FE) TP (VC)

3. Put disc (YEDS-18) in and playback. 4. Confirm that oscilloscope waveform is clear and check if RF signal level is correct or not. Note : A clear RF signal waveform means that the shape " " can be clearly distinguished at the center of the waveform.
RF signal waveform VOLT/DIV : 200mV TIME/DIV : 500nS

level : 1.2 0.20 Vp-p

+0.25

E-F Balance (1 Track Jump) Check Procedure : 1. Connect oscilloscope to test point TP (FE) on BD board. 2. Connect between test point TP (FEI) and TP (VC) by lead wire. 3. Turn Power switch on. 4. Put disc (YEDS-18) in and turn Power switch on again and actuate the focus search. (Actuate the focus search when disc table is moving in and out.) 5. Check if the oscilloscope waveform (S-curve) is symmetrical between A and B. And confirm peak to peak level within 3±1 Vp-p.
S-curve waveform symmetry oscilloscope (DC range) BD board TP (TE) TP (VC)

Procedure : 1. Connect oscilloscope to test point TP (TE) on BD board . 2. Turn Power switch on. 3. Put disc (YEDS-18) in to play the number five track. 4. Press the "P (pause)" button. (Becomes the 1 track jump mode.) 5. Check the level B of the oscilloscope's waveform and the A (DC voltage) of the following : A/B×100 = less than ± 20%.
1 track jump waveform

A B

within 3±1 Vp-p

Center of the waveform

6. After check, remove the lead wire connected in step 2. Note : · Try to measure several times to make sure than the ratio of A : B or B : A is more than 10 : 7. · Set sweep time as long as possible and set the brightness to obtain best waveform. RF Level Check
oscilloscope BD board TP (RF) TP (VC)

B A (DC voltage)

level : 1.5±0.7Vp-p

symmetry

RF PLL Free-run Frequency Check Procedure : 1. Connect frequency counter to test point (PLCK) with lead wire.
frequency counter MAIN board TP (PLCK)

Procedure : 1. Connect oscilloscope to test point TP (RF) on BD board. 2. Turn Power switch on.

2. Turn Power switch on. 3. Confirm that reading on frequency counter is 4.3218MHz.

7

Adjustment Location : BD board
BD board (conductor side)

1 IC103 10

20 (RF) 11 (TE) (VC)

(FE) (FEI)

(PLCK) IC101

8

SECTION 4 DIAGRAMS
4-1. IC PIN FUNCTIONS · IC101 CXD2545Q (DIGITAL SERVO & DIGITAL SIGNAL PROCESSOR)
Pin No. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 Pin Name SRON SRDR SFON TFDR TRON TRDR TFON FFDR FRON FRDR FFON VCOO VCOI TEST DVSS TES2 TES3 PDO VPCO VCKI AVD2 IGEN AVS2 ADIO RFC RFDC TE SE FE VC FILO FILI PCO CLTV AVS1 RFAC BIAS ASYI ASYO AVD1 DVDD ASYE PSSL WDCK LRCK DATA BCLK I/O O O O O O O O O O O O O I I -- I I O O I -- I -- I O I I I I I O I O I -- I I I O -- -- I I O O O O Sled drive output (Not used.) Sled drive output Sled drive output (Not used.) Tracking drive output Tracking drive output (Not used.) Tracking drive output Tracking drive output (Not used.) Focus drive output Focus drive output (Not used.) Focus drive output Focus drive output (Not used.) VCO output for analog EFM PLL. (Not used.) VCO input for analog EFM PLL. (Ground) TEST pin connected normally to Ground. Digital Ground TEST pin connected normally to Ground. TEST pin connected normally to Ground. Charge-pump output for analog EFM PLL. (Not used.) Charge-pump output for variable pitch PLL. (Not used.) Clock input from variable pitch external VCO. (Ground) Analog power supply Power supply pin for operational amplifiers. Analog Ground (Not used.) (Not used.) RF signal input Tracking error signal input Sled error signal input Focus error signal input Center voltage input pin Filter output for master PLL. Filter input for master PLL. Charge-pump output for master PLL. Control voltage input for master VCO. Analog Ground EFM signal input Asymmetry circuit constant current input Asymmetry comparate voltage input EFM full swing output Analog power supply Digital power supply Asymmetry circuit ON/OFF Audio data output mode selection input 48-bit slot D/A interface. Word clock 48-bit slot D/A interface. LR clock DA 16 output when PSSL=1. 48-bit slot serial data when PSSL=0. DA 15 output when PSSL=1. 48-bit slot data when PSSL=0. Function

9

Pin No. 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96

Pin Name 64DATA 64BCLK 64LRCK GTOP XUGF XPLCK GFS PFCK C2PO XRAOF MNT3 MNT2 MNT1 MNT0 XTAI XTAO XTSL DVSS FSTI FSTO FSOF C16M MD2 DOUT EMPH WFCK SCOR SBSO EXCK SUBQ SQCK MUTE SENS XRST DIRC SCLK DFSW ATSK DATA XLAT CLOK COUT DVDD MIRR DFCT FOK FSW MON MDP

I/O O O O O O O O O O O O O O O I O I I O O O I O O O O O I O I I O I I I I I I I I O O O O O O O

Function DA 14 output when PSSL=1. 64-bit slot data when PSSL=0. (Not used.) DA 13 output when PSSL=1. 64-bit slot data when PSSL=0. (Not used.) DA 12 output when PSSL=1. 64-bit slot data when PSSL=0. (Not used.) DA 11 output when PSSL=1. GTOP output when PSSL=0. (Not used.) DA 10 output when PSSL=1. XUGF output when PSSL=0. (Not used.) DA 09 output when PSSL=1. XPLCK output when PSSL=0. DA 08 output when PSSL=1. GFS output when PSSL=0. DA 07 output when PSSL=1. RFCK output when PSSL=0. DA 06 output when PSSL=1. C2PO output when PSSL=0. (Not used.) DA 05 output when PSSL=1. XRAOF output when PSSL=0. (Not used.) DA 04 output when PSSL=1. MNT3 output when PSSL=0. DA 03 output when PSSL=1. MNT2 output when PSSL=0. DA 02 output when PSSL=1. MNT1 output when PSSL=0. DA 01 output when PSSL=1. MNT0 output when PSSL=0. X'tal oscillator circuit input X'tal oscillator circuit output (Not used.) X'tal selection input pin (Ground) Digital Ground 2/3 divider input of pins 62 and 63. 2/3 divider output of pins 62 and 63. (Not used.) 16.9344MHz output (Not used.) Digital-out ON/OFF control pin (+5V) Digital-out output pin Playback disc output in emphasis mode. (Not used.) WFCK output Sub-code sync output Sub-P through Sub-W serial output (Not used.) Clock input for SBSO read-out. (Ground) Sub-Q 80-bit output Clock input for SQSO read-out. Muting selection pin SENS output System reset Used in 1-track jump mode (+5V) SENS serial data read-out clock DFCT selection pin (Ground) Input pin for anti-shock. (Ground) Serial data input, supplied from CPU. Latch input, supplied from CPU. Serial data transfer clock input, supplied from CPU. Numbers of track counted signal output. (Not used.) Digital power supply Mirror signal output Defect signal output Focus OK output Output to select spindle motor output filter. (Not used.) Output to control ON/OFF of spindle motor. (Not used.) Output to control spindle motor servo

10

Pin No. 97 98 99 100

Pin Name MDS LOCK SSTP SFDR

I/O O O I O

Function Output to control spindle motor servo. (Not used.) GFS is sampled by 460Hz. H when GFS is H. (Not used.) Input signal to detect disc innermost track. Sled drive output

11

· IC501 CXP82612-021Q (MASTER CONTROL)
Pin No. 1 2 3 4-6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26,27 28 29 30 31 32 33 34-41 42-62 63-70 71 72 73 74 75-77 78 79,80 Pin Name TIMER RM +5V PGML CLK SENSE DATA SQCK SUBQ AMUTE LDON XLT RV+ RVLDOUT LDIN KEY0 KEY1 KEY2 KEY3 KEY4,KEY5 ADJ/AFADJ IN/OUTSW RST EXTAL XTAL VSS S1-S21 1G-7G VFDP(-30V) VDD(+5V) +5V SEL1 SCOR SEL2,SEL3 I/O I O O I O O I O O O O I I I I I I I I O O O I Connected to +5V. Audio bus input Connected to +5V. Not used. (Open) Latch signal output to digital filter (IC201). Serial clock output SENSE signal input Serial data output Read out clock output for subcode Q data. Subcode Q data input Not used. (Open) Analog muting control signal output Optical pick-up laser diode control output Serial data latch signal output Not used. (Open) Not used. (Open) Not used. (Open) Loading motor control signal output Loading motor control signal input Key input (S530) Key input (S520-S527) Key input (S501-S506) Connected to +5V. Key input (S531) ADJ/AFJ test pin Loading IN/OUT switch input Reset signal input Clock input (4MHz) Clock output (4MHz) Ground Not used. (Open) FL segment output FL grid output -30V pin for FL display tube. +5V pin +5V pin Connected to Ground. Connected to Ground. Read out timing signal input for subcode Q data. Connected to +5V. Function

12

SECTION 5 EXPLODED VIEWS
NOTE: · The mechanical parts with no reference number in the exploded views are not supplied. · Items marked "*" are not stocked since they are seldom required for routine service. Some delay should be anticipated when ordering these items. · Abbreviation AUS : Australian model CH : Chinese model G : German model EE : East European model · -XX and -X mean standardized parts, so they may have some difference from the original one. · Color Indication of Appearance Parts Example : KNOB, BALANCE (WHITE) ... (RED) N Parts Color Cabinet's Color N · Hardware (# mark) list and accessories and packing materials are given in the last of this parts list. The components identified by mark ! or dotted line with mark. ! are critical for safety. Replace only with part number specified.

5-1. CASE SECTION 2
#1 CDM14-5BD20

1
#1

4 3 8 9 10 11 12
not supplied

7 5

5 5

2

24

6

5 13 16

5

20

19

not supplied

17
Ref. No. * 1 * 1 2 2 3 4 5 6 * 7 * 8 9 9 10 10 10 Part No. 4-978-901-21 4-978-901-91 3-363-099-01 3-704-366-31 4-956-370-02 1-776-100-11 4-951-620-01 1-776-099-11 A-4673-727-A 1-658-840-11 4-977-589-01 4-977-589-11 4-977-588-01 4-977-588-11 4-977-588-41 Description

18

#1 supplied with J601
Remark Ref. No. 11 11 12 12 12 13 16 17 17 18 * 19 20 20 24 Part No. X-4946-531-1 X-4946-957-1 X-4947-021-1 X-4947-022-1 X-4947-083-1 4-963-404-21 4-977-583-01 4-977-590-01 4-977-590-11 3-354-981-01 1-658-839-11 X-4947-207-1 X-4947-124-1 4-977-584-11 Description Remark

CASE (408226) (BLACK) CASE (408226) (SILVER) SCREW (CASE 3 TP2) (AEP,UK,G,EE) SCREW (CASE) (M3X6) (US,E,AUS,CH) BAND, PLUG FIXED (UK,AUS) WIRE (FLAT TYPE) (23 CORE) SCREW (2.6X8), +BVTP WIRE (FLAT TYPE) (21 CORE) PANEL BOARD, COMPLETE POWER SW BOARD BUTTON (POWER) (BLACK) BUTTON (POWER) (SILVER) PANEL, LOADING (XE500:BLACK) PANEL, LOADING (XE400) PANEL, LOADING (XE500:SILVER)

PANEL ASSY, FRONT (AEP:BLACK,UK,G,EE) PANEL ASSY, FRONT (SILVER) PANEL ASSY, FRONT (XE500:E, AUS, CH) PANEL ASSY, FRONT (XE500:US) PANEL ASSY, FRONT (XE400) EMBLEM (5-A), SONY (US,E,AUS,CH) BUTTON (PLAY) (BLACK) KNOB (AMS) (US,E,AUS,CH) KNOB (AMS) (SILVER) SPRING (SUS), RING H.P BOARD FOOT ASSY (F50150S) (BLACK) FOOT ASSY (F50150S) (SILVER) BUTTON (MODE)

28

5-2. BACK PANEL SECTION

UK Model CNP901

US Model CNP901

AEP, G, EE Model CNP901

E Model

CNP901

55 52
#1 CH Model CNP901

51

#2 #1 #1 T901 #1 AUS Model CNP901

56

53

54

not supplied
The components identified by mark ! or dotted line with mark. ! are critical for safety. Replace only with part number specified.

Ref. No. * * * * * * * * * 51 51 52 52 52 52 52 52 52 53

Part No. 3-703-244-00 3-703-571-11 4-977-587-11 4-977-587-31 4-977-587-41 4-977-587-51 4-977-587-91 4-978-388-01 4-978-388-11 A-4673-738-A

Description BUSHING, CORD (EXCEPT US,E) BUSHING (S) (4516), CORD (US,E) PANEL, BACK (XE500:US) PANEL, BACK (E) PANEL, BACK (AUS) PANEL, BACK (XE400) PANEL, BACK (CH) PANEL, BACK (AEP,G,EE) PANEL, BACK (UK) MAIN BOARD, COMPLETE (XE400)

Remark

Ref. No. * 54 ! 55 ! 56 ! CNP901 ! CNP901 ! CNP901 ! CNP901 ! CNP901 ! CNP901 ! T901 ! T901 ! T901

Part No. 4-954-051-51 1-569-007-11 1-569-008-11 1-558-943-81 1-558-945-21 1-575-651-21 1-696-845-11 1-696-907-11 1-696-966-11 1-423-979-11

Description HOLDER, PC BOARD ADAPTOR, CONVERSION 2P (E) ADAPTOR, CONVERSION 2P (CH) CORD, POWER (E) CORD, POWER (POLAR.SPT-1) (US) CORD, POWER (AEP,G,EE) CORD, POWER (AUS) CORD, POWER (UK) CORD, POWER (CH) TRANSFORMER, POWER (EXCEPT US,E)

Remark

* 53 53 53

A-4673-739-A MAIN BOARD, COMPLETE (E) A-4673-740-A MAIN BOARD, COMPLETE (EXCEPT US,E) A-4673-753-A MAIN BOARD, COMPLETE (XE500:US)

1-426-621-11 TRANSFORMER, POWER (US) 1-426-622-11 TRANSFORMER, POWER (E)

29

5-3. CD MECHANISM SECTION (CDM14-5BD20)

111 110

112

109
BU-5BD20

108 114

113 107 106 104 115

105

#3

103

102

M151

101

Ref. No. * 101 102 102 * 103 104 105 106 107 108

Part No. 1-645-721-11 4-933-111-11 4-933-111-41 4-917-583-21 4-927-649-01 4-933-109-01 4-927-651-01 4-967-268-01 4-933-107-01

Description LOADING BOARD CHASSIS (MD) (AEP,UK,G,EE) CHASSIS (MD) (US,E,AUS,CH) BRACKET, YOKE BELT CAM PULLEY (S) GEAR (C) GEAR (PL)

Remark

Ref. No. 109 110 * 111 112 113 114 115 M151

Part No. 4-933-112-11 4-933-110-41 1-452-538-11 4-933-134-01 4-959-996-01

Description TABLE, DISC HOLDER (MG) MAGNET SCREW (+PTPWH M2.6X6) SPRING (932), COMPRESSION

Remark

4-933-129-01 HOLDER (BU) 4-925-315-31 DAMPER A-4604-363-A MOTOR (L) ASSY (LOADING)

30

5-4. BASE UNIT SECTION (BU-5BD20) 155

rA

156

#4

153
M101 (Including rA)

152 158

152

M102

157

151
#5
The components identified by mark ! or dotted line with mark. ! are critical for safety. Replace only with part number specified.

Ref. No. 151 * 151 152 153 ! 155

Part No. A-4673-509-A A-4673-511-A 4-951-940-01 4-917-565-01 8-848-367-11

Description BD BOARD, COMPLETE (US,E,AUS,CH) BD BOARD, COMPLETE (AEP,UK,G,EE) INSULATOR (BU) SHAFT, SLED PICK-UP BLOCK, OPTICAL KSS-213B/K-N

Remark

Ref. No. 156 157 158 M101 M102

Part No. 4-917-567-21 4-917-564-01 1-769-069-11 X-4917-523-3 X-4917-504-1

Description GEAR (M) GEAR (P), FLATNESS WIRE (FLAT TYPE) (16 CORE) BASE (OUTSERT) ASSY (SPINDLE) MOTOR ASSY (SLED)

Remark

31

BD
NOTE: · Due to standardization, replacements in the parts list may be different from the parts specified in the diagrams or the components used on the set. · -XX and -X mean standardized parts, so they may have some difference from the original one. · RESISTORS All resistors are in ohms. METAL:Metal-film resistor. METAL OXIDE: Metal oxide-film resistor. F:nonflammable

SECTION 6 ELECTRICAL PARTS LIST
· Items marked "*" are not stocked since they are seldom required for routine service. Some delay should be anticipated when ordering these items. · SEMICONDUCTORS In each case, u : µ, for example: uA.. : µA.. uPA.. : µPA.. uPB.. : µPB.. uPC.. : µPC.. uPD.. : µPD.. · CAPACITORS uF : µF · COILS uH : µH The components identified by mark ! or dotted line with mark. ! are critical for safety. Replace only with part number specified. When indicating parts by reference number, please include the board. · Abbreviation AUS : Australian model CH : Chinese model G : German model EE : East European model Description < TRANSISTOR > Q101 470PF 0.1uF 470PF 4.7uF 1uF 1uF 0.047uF 0.0015uF 0.0047uF 100PF 0.1uF 0.1uF 47uF 47uF 100uF 0.001uF 15PF 0.01uF 0.47uF 0.1uF 0.1uF 27PF 0.1uF 0.33uF 27PF 0.0015uF 0.0068uF 0.1uF 10% 10% 10% 50V 25V 50V 16V 16V 16V 50V 50V 50V 50V 25V 25V 4V 4V 4V 50V 50V 50V 25V 25V 25V 50V 25V 25V 50V 50V 50V 25V 8-729-010-08 TRANSISTOR < RESISTOR > R101 R102 R103 R104 R105 R106 R107 R108 R109 R110 1-216-077-00 1-216-097-00 1-216-077-00 1-216-085-00 1-216-097-00 1-216-061-00 1-216-061-00 1-216-073-00 1-216-121-00 1-216-025-00 METAL CHIP METAL GLAZE METAL CHIP METAL CHIP METAL GLAZE METAL CHIP METAL CHIP METAL CHIP METAL GLAZE METAL GLAZE METAL GLAZE METAL CHIP METAL GLAZE METAL GLAZE METAL CHIP 15K 100K 15K 33K 100K 3.3K 3.3K 10K 1M 100 1K 10K 100K 1K 330 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W MSB710-R Remark

Ref. No. *

Part No.

Description

Remark

Ref. No.

Part No.

A-4673-509-A BD BOARD, COMPLETE (US,E,AUS,CH) A-4673-511-A BD BOARD, COMPLETE (AEP,UK,G,EE) ******************* < CAPACITOR > C101 C102 C103 C105 C106 C107 C108 C109 C110 C111 C112 C113 C115 C116 C117 C118 C119 C123 C124 C140 C141 C151 C153 C154 C156 C157 C159 C161 1-163-005-11 1-163-038-00 1-163-005-11 1-135-155-21 1-164-346-11 1-164-346-11 1-163-035-00 1-163-145-00 1-163-017-00 1-163-251-11 1-163-038-00 1-163-038-00 1-126-607-11 1-126-607-11 1-126-209-11 1-163-275-11 1-163-231-11 1-164-232-11 1-164-005-11 1-163-038-00 1-163-038-00 1-163-237-11 1-163-038-00 1-164-336-11 1-163-237-11 CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP TANTALUM CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP ELECT CHIP ELECT CHIP ELECT CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP

5% 5% 5%

20% 20% 20% 5% 5%

R112 1-216-049-11 R123 1-216-073-00 R124 1-216-097-00 R125-127 1-216-049-11 R131 1-216-037-00 R135-138 1-216-295-00 R141 1-216-089-00 R142 1-216-081-00 R143 1-216-103-00 R144 1-216-103-00 R146 R147 R148 R149 R158 R159 R160 R161 R162 1-216-073-00 1-216-081-00 1-216-001-00 1-216-003-11 1-216-111-00 1-216-101-00 1-216-295-00 1-216-308-00 1-216-101-00

5%

CONDUCTOR, CHIP METAL GLAZE METAL CHIP METAL GLAZE METAL GLAZE METAL CHIP METAL CHIP METAL CHIP METAL GLAZE METAL GLAZE

47K 22K 180K 180K 10K 22K 10 12 390K

(2012) 5% 1/10W 5% 1/10W 5% 1/10W 5% 1/10W 5% 5% 5% 5% 5% 1/10W 1/10W 1/10W 1/10W 1/10W

5% 5% 10%

1-163-145-00 CERAMIC CHIP 1-163-019-00 CERAMIC CHIP 1-163-038-00 CERAMIC CHIP < CONNECTOR >

CN101 1-770-072-11 CONNECTOR, FFC 23P CN102 1-770-014-11 CONNECTOR, FFC/FPC 16P < IC > IC101 IC102 IC103 8-752-369-78 IC 8-759-176-09 IC 8-752-072-45 IC CXD2545Q BA6392FP CXA1821M-T6

METAL CHIP 150K CONDUCTOR, CHIP METAL CHIP 4.7 METAL CHIP 150K < SWITCH >

5% 1/10W (2012) 5% 1/10W 5% 1/10W

S101 1-572-085-11 SWITCH, LEAF (LIMIT SW) **************************************************************

32

H.P
Ref. No. * Part No. Description Remark Ref. No. C254 C255 C256 C256 C604 C605 C608 1-162-291-31 CERAMIC 1-162-291-31 CERAMIC 1-164-159-21 CERAMIC < CONNECTOR > C258 * CN601 1-568-941-11 PIN, CONNECTOR 3P < JACK > J601 1-568-519-41 JACK, LARGE TYPE (PHONES) < COIL > L601-603 1-410-397-21 FERRITE BEAD INDUCTOR 1.1uH ************************************************************** * 1-645-721-11 LOADING BOARD ************** < CONNECTOR > * CN151 1-568-943-11 PIN, CONNECTOR 5P < SWITCH > S151 1-572-086-11 SWITCH, LEAF (LOAD OUT) S152 1-572-086-11 SWITCH, LEAF (LOAD IN) ************************************************************** * * * * A-4673-738-A A-4673-739-A A-4673-740-A A-4673-753-A MAIN BOARD, COMPLETE (XE400) MAIN BOARD, COMPLETE (E) MAIN BOARD, COMPLETE (EXCEPT US,E) MAIN BOARD, COMPLETE (XE500:US) ********************* < CAPACITOR > C201 C201 C202 C205 C211 1-101-006-00 CERAMIC 1-161-494-00 CERAMIC 1-162-290-31 CERAMIC 1-104-666-11 ELECT 1-101-006-00 CERAMIC 0.047uF 0.022uF 470PF 220uF 0.047uF 50V (US,E,AUS,CH) 25V (AEP,UK,G,EE) 10% 50V 20% 25V 50V (US,E,AUS,CH) 25V (AEP,UK,G,EE) 10% 50V 50V (US,E,AUS,CH) 25V (AEP,UK,G,EE) 20% 16V C301 C302 C303 C304 C305 C306 C306 C307 C351 C352 C353 C354 C355 C356 C356 1-162-215-31 1-130-479-00 1-126-933-11 1-162-215-31 1-130-472-00 CERAMIC MYLAR ELECT CERAMIC MYLAR C259 C264 C280 1-126-933-11 ELECT 1-162-282-31 CERAMIC 1-164-159-21 CERAMIC 1-161-494-00 CERAMIC 560PF 560PF 0.1uF 10% 10% 50V 50V 50V C257 C258 Part No. Description 1-658-839-11 H.P BOARD ********* < CAPACITOR > 1-161-494-00 CERAMIC 1-126-933-11 ELECT 1-101-006-00 CERAMIC 1-162-199-31 CERAMIC 1-162-199-31 CERAMIC 1-101-006-00 CERAMIC

LOADING
10PF 10PF 0.047uF 0.022uF 100uF 0.047uF 0.022uF 100uF 100PF 0.1uF 47PF 0.0047uF 100uF 47PF 0.0012uF 0.047uF 0.022uF 560PF 47PF 0.0047uF 100uF 47PF 0.0012uF 0.047uF 0.022uF

MAIN
Remark 50V 50V 50V (US,E,AUS,CH) 25V (AEP,UK,G,EE) 20% 16V 50V (US,E,AUS,CH) 25V (AEP,UK,G,EE) 20% 16V 10% 50V 50V 5% 5% 20% 5% 5% 50V 50V 16V 50V 50V 5% 5%

1-101-006-00 CERAMIC 1-161-494-00 CERAMIC 1-162-291-31 CERAMIC 1-162-215-31 CERAMIC 1-130-479-00 MYLAR 1-126-933-11 1-162-215-31 1-130-472-00 1-101-006-00 ELECT CERAMIC MYLAR CERAMIC

50V (US,E,AUS,CH) 25V (AEP,UK,G,EE) 10% 50V 5% 50V 5% 50V 16V 50V 50V 50V (US,E,AUS,CH) 25V (AEP,UK,G,EE) 50V 50V 50V (US,E,AUS,CH) 25V (AEP,UK,G,EE) 30% 16V 10% 20% 20% 5% 5%

1-161-494-00 CERAMIC

C357 C400 C401 C401 C402 C403 C404 C404 C481 C481

1-162-291-31 CERAMIC 1-126-964-11 ELECT 1-101-006-00 CERAMIC 1-161-494-00 CERAMIC 1-162-306-11 CERAMIC 1-104-666-11 ELECT 1-101-006-00 CERAMIC 1-161-494-00 CERAMIC 1-101-006-00 CERAMIC 1-161-494-00 CERAMIC

560PF 10uF 0.047uF 0.022uF 0.01uF 220uF

C211 C251 C252 C252 C253

1-161-494-00 CERAMIC 1-162-282-31 CERAMIC 1-101-006-00 CERAMIC 1-161-494-00 CERAMIC 1-126-933-11 ELECT

0.022uF 100PF 0.047uF 0.022uF 100uF

20% 25V (XE500) 0.047uF 50V (XE500:US,E,AUS,CH) 0.022uF 25V (AEP,UK,G,EE) 0.047uF 50V (US,E,AUS,CH) 0.022uF 25V (AEP,UK,G,EE) 0.047uF 0.022uF 50V (US,E,AUS,CH) 25V (AEP,UK,G,EE)

C601 C601

1-101-006-00 CERAMIC 1-161-494-00 CERAMIC

33

MAIN
Ref. No. C602 C602 C607 C607 C680 Part No. Description 0.047uF 0.022uF 0.047uF 0.022uF 0.047uF Remark 50V (US,E,AUS,CH) 25V (AEP,UK,G,EE) 50V (US,E,AUS,CH) 25V (AEP,UK,G,EE) 50V (US,E,AUS,CH) 25V (AEP,UK,G,EE) 20% 50V 10% 50V 20% 25V 20% 50V 20% 20% 20% 20% 20% 20% 20% 20% 16V 50V 50V 50V 50V Ref. No. D403 D701 D702 D703 D704 D705 D706 D707 D708 D901 D902 D903 D904 D905 Part No. 8-719-010-34 8-719-815-85 8-719-815-85 8-719-815-85 8-719-815-85 8-719-815-85 8-719-815-85 8-719-815-85 8-719-815-85 8-719-200-82 8-719-200-82 8-719-200-82 8-719-200-82 8-719-200-82 Description DIODE DIODE DIODE DIODE DIODE DIODE DIODE DIODE DIODE DIODE DIODE DIODE DIODE DIODE < IC > C706 1-126-933-11 C707 1-124-903-11 C708-710 1-126-964-11 C711 1-124-903-11 C712 1-124-903-11 C901 C902 C903 C904 C904 1-126-939-11 1-126-768-11 1-128-576-11 1-101-006-00 ELECT ELECT ELECT ELECT ELECT ELECT ELECT ELECT CERAMIC 100uF 1uF 10uF 1uF 1uF 10000uF 2200uF 100uF 0.047uF 0.022uF IC201 IC301 IC302 IC401 IC601 IC701 IC801 8-759-362-47 8-759-634-51 8-759-634-51 8-759-822-09 8-759-634-51 IC IC IC IC IC CXD8567AM M5218AP M5218AP LB1641 M5218AP LA5601 GP1F32T (DIGITAL OUT OPTICAL) (XE500) UZ-4.7BSC 1S1585 1S1585 1S1585 1S1585 1S1585 1S1585 (AEP,UK,G,EE) 1S1585 1S1585 (AEP,UK,G,EE) 11ES2 11ES2 11ES2 11ES2 11ES2 Remark 1-101-006-00 CERAMIC 1-161-494-00 CERAMIC 1-101-006-00 CERAMIC 1-161-494-00 CERAMIC 1-101-006-00 CERAMIC

C680 C702 C703 C704 C705

1-161-494-00 CERAMIC 1-126-964-11 1-162-294-31 1-104-666-11 1-126-964-11 ELECT CERAMIC ELECT ELECT

0.022uF 10uF 0.001uF 220uF 10uF

1-161-494-00 CERAMIC

16V 16V 63V 50V (US,E,AUS,CH) 25V (AEP,UK,G,EE) 50V (US,E,AUS,CH) 25V (AEP,UK,G,EE) 50V (US,E,AUS,CH) 50V (AEP,UK,G,EE) 50V (US,E,AUS,CH) 50V (AEP,UK,G,EE) 50V (US,E,AUS,CH) 50V (AEP,UK,G,EE)

8-759-821-93 IC 8-749-921-12 IC

< JACK > J301 1-770-719-11 JACK, PIN 2P (LINE OUT VARIABLE) < COIL >

C905 C905 C906 C906 C907

1-101-006-00 CERAMIC 1-161-494-00 CERAMIC 1-101-006-00 CERAMIC 1-164-159-21 CERAMIC 1-101-006-00 CERAMIC

0.047uF 0.022uF 0.047uF 0.1uF 0.047uF

L201 L205 L206 L211 L220 L251 L253 L254 L254 L701 L702

1-410-322-11 1-410-322-11 1-410-507-11 1-410-507-11 1-410-322-11 1-410-322-11 1-410-322-11 1-410-397-21 1-410-507-11 1-414-223-11

INDUCTOR INDUCTOR INDUCTOR INDUCTOR INDUCTOR

3.3uH (EXCEPT US) 3.3uH (XE500) 6.8uH (XE500) 6.8uH (XE500) 3.3uH

C907 C908 C908

1-164-159-21 CERAMIC 1-101-006-00 CERAMIC 1-164-159-21 CERAMIC

0.1uF 0.047uF 0.1uF

INDUCTOR 3.3uH INDUCTOR 3.3uH FERRITE BEAD INDUCTOR 1.1uH (US) INDUCTOR 6.8uH (EXCEPT US) INDUCTOR 470uH 0uH (US)

1-412-473-21 INDUCTOR

< TRANSISTOR > Q301 Q351 Q400 Q401 Q601 Q602 Q701 Q702 8-729-922-37 8-729-922-37 8-729-230-46 8-729-019-64 8-729-922-37 TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR 2SD2144S 2SD2144S 2SA1048TP-YG 2SB1041 2SD2144S 2SD2144S DTA144ESA-TP DTA144ESA-TP

< CONNECTOR > * CN201 1-568-839-11 SOCKET, CONNECTOR 23P CN202 1-568-838-11 SOCKET, CONNECTOR 21P CN901 1-580-230-11 PIN, CONNECTOR (PC BOARD) 2P (AEP,UK,G,EE) < DIODE > D400 D401 D402 8-719-982-22 DIODE 8-719-815-85 DIODE 8-719-109-97 DIODE MTZJ-30D 1S1585 RD6.8ES-B2

8-729-922-37 TRANSISTOR 8-729-029-56 TRANSISTOR 8-729-029-56 TRANSISTOR

34

MAIN
Ref. No. Part No. Description < RESISTOR > R201 R202 R202 1-249-417-11 CARBON 1-247-807-11 CARBON 1-247-815-00 CARBON 1K 100 220 5% 5% 5% 1/4W 1/4W (US) 1/4W (EXCEPT US) 1/4W 1/4W (US) Remark Ref. No. R702 R703 R704 R705 Part No. 1-249-441-11 1-249-441-11 1-247-807-11 1-249-417-11 Description CARBON CARBON CARBON CARBON < SWITCH > ! S901 100K 100K 100 1K 5% 5% 5% 5%

PANEL
Remark 1/4W 1/4W 1/4W 1/4W

R203-208 1-249-417-11 CARBON R220 1-247-815-00 CARBON R221 R221 R251 R252 R253 1-247-804-11 CARBON 1-249-400-11 CARBON 1-249-436-11 CARBON 1-249-436-11 CARBON 1-249-424-11 CARBON R255 R256 R257 R301 R302 1-249-436-11 1-249-436-11 1-247-807-11 1-249-431-11 1-249-431-11 CARBON CARBON CARBON CARBON CARBON

1K 220 75 39 39K 39K 3.9K 39K 39K 100 15K 15K

5% 5% 5% 5%

1-572-675-11 SWITCH, POWER VOLTAGE CHANGE (VOLTAGE SELECTOR) (E) < TRANSFORMER >

1/4W (US) 1/4W (EXCEPT US) 5% 1/4W 5% 1/4W 5% 5% 5% 5% 5% 5% 1/4W 1/4W 1/4W 1/4W 1/4W 1/4W

! T901 ! T901 ! T901

1-423-979-11 TRANSFORMER, POWER (EXCEPT US,E) 1-426-621-11 TRANSFORMER, POWER (US) 1-426-622-11 TRANSFORMER, POWER (E) < TERMINAL >

* TPT901 1-535-771-11 TERMINAL (US,E,AUS,CH) * TPT902 1-535-771-11 TERMINAL (US,E,AUS,CH) < VIBRATOR > X201 1-579-833-21 VIBRATOR, CRYSTAL (33.8688MHz) (XE400) X201 1-579-834-11 VIBRATOR, CRYSTAL (33.8688MHz) (XE500) ************************************************************** * A-4673-727-A PANEL BOARD, COMPLETE ********************** < CAPACITOR >

R303 R304 R305 R306 R307 R308 R309 R310 R351 R352 R353 R354 R355 R356 R357 R358 R359 R360 R400 R401

1-249-437-11 1-249-419-11 1-249-419-11 1-249-417-11 1-249-437-11 1-249-441-11 1-249-419-11 1-247-807-11 1-249-431-11 1-249-431-11 1-249-437-11 1-249-419-11 1-249-419-11 1-249-417-11 1-249-437-11 1-249-441-11 1-249-419-11 1-247-807-11 1-249-432-11 1-249-432-11

CARBON CARBON CARBON CARBON CARBON CARBON CARBON CARBON CARBON CARBON CARBON CARBON CARBON CARBON CARBON CARBON CARBON CARBON CARBON CARBON

47K 1.5K 1.5K 1K 47K 100K 1.5K 100 15K 15K 47K 1.5K 1.5K 1K 47K 100K 1.5K 100 18K 18K

5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5%

1/4W 1/4W 1/4W 1/4W 1/4W 1/4W 1/4W 1/4W 1/4W 1/4W 1/4W 1/4W 1/4W 1/4W 1/4W 1/4W 1/4W 1/4W 1/4W 1/4W

C501-503 1-161-494-00 CERAMIC C505 1-161-494-00 CERAMIC < CONNECTOR >

0.022uF 0.022uF

25V 25V

* CN501 1-568-864-11 SOCKET, CONNECTOR 21P < FLUORESCENT INDICATOR TUBE > FL501 1-517-297-21 INDICATOR TUBE, FLUORESCENT < IC > IC501 IC502 8-752-869-51 IC CXP82612-021Q 8-741-810-59 IC SBX1810-59 < TRANSISTOR >

R402 R403 R404 R405 R406 R451 R601 R602 R603 R604 R701

1-249-441-11 1-249-425-11 1-249-441-11 1-249-432-11 1-249-427-11 1-249-427-11 1-249-403-11 1-249-403-11 1-249-419-11 1-249-419-11

CARBON CARBON CARBON CARBON CARBON CARBON CARBON CARBON CARBON CARBON

100K 4.7K 100K 18K 6.8K 6.8K 68 68 1.5K 1.5K 2.7K

5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5%

1/4W 1/4W 1/4W 1/4W 1/4W 1/4W 1/4W 1/4W 1/4W 1/4W 1/4W

Q501

8-729-029-67 TRANSISTOR DTC114ESA-TP < RESISTOR >

R501 R502 R503 R504 R505 R506

1-249-427-11 1-249-427-11 1-249-431-11 1-249-427-11 1-249-415-11

CARBON CARBON CARBON CARBON CARBON

6.8K 6.8K 15K 6.8K 680 1K

5% 5% 5% 5% 5% 5%

1/4W 1/4W 1/4W 1/4W 1/4W 1/4W

1-249-417-11 CARBON

1-249-422-11 CARBON

The components identified by mark ! or dotted line with mark. ! are critical for safety. Replace only with part number specified.

35

PANEL
Ref. No. R507 R508 R509 R510 R511 R512 R513 R514 R515 R516 R517 R519 R520 R530 R531

POWER SW
Description CARBON CARBON CARBON CARBON CARBON CARBON CARBON CARBON CARBON CARBON CARBON CARBON CARBON CARBON CARBON < SWITCH > 1.5K 2.2K 3.3K 6.8K 680 1K 1.5K 2.2K 3.3K 6.8K 15K 100K 6.8K 10K 10K 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% Remark 1/4W 1/4W 1/4W 1/4W 1/4W 1/4W 1/4W 1/4W 1/4W 1/4W 1/4W 1/4W 1/4W 1/4W 1/4W Ref. No. Part No. Description MISCELLANEOUS *************** 4 6 ! 55 ! 56 * 111 ! 155 158 ! CNP901 ! CNP901 ! CNP901 ! CNP901 ! CNP901 ! CNP901 M101 M102 1-776-100-11 1-776-099-11 1-569-007-11 1-569-008-11 1-452-538-11 8-848-367-11 1-769-069-11 1-558-943-81 1-558-945-21 1-575-651-21 1-696-845-11 1-696-907-11 1-696-966-11 X-4917-523-3 X-4917-504-1 WIRE (FLAT TYPE) (23 CORE) WIRE (FLAT TYPE) (21 CORE) ADAPTOR, CONVERSION 2P (E) ADAPTOR, CONVERSION 2P (CH) MAGNET PICK-UP BLOCK, OPTICAL KSS-213B/K-N WIRE (FLAT TYPE) (16 CORE) CORD, POWER (E) CORD, POWER (POLAR.SPT-1) (US) CORD, POWER (AEP,G,EE) CORD, POWER (AUS) CORD, POWER (UK) CORD, POWER (CH) BASE (OUTSERT) ASSY (SPINDLE) MOTOR ASSY (SLED) Remark

Part No. 1-249-419-11 1-249-421-11 1-249-423-11 1-249-427-11 1-249-415-11 1-249-417-11 1-249-419-11 1-249-421-11 1-249-423-11 1-249-427-11 1-249-431-11 1-249-441-11 1-249-427-11 1-249-429-11 1-249-429-11

S501 S502 S503 S504 S505 S506 S520 S521 S522 S523 S524 S525 S526 S527 S530 S531

1-554-303-21 1-554-303-21 1-554-303-21 1-554-303-21 1-554-303-21 1-554-303-21 1-554-303-21 1-554-303-21 1-554-303-21 1-554-303-21 1-554-303-21 1-554-303-21 1-554-303-21 1-554-303-21 1-554-303-21

SWITCH, TACTILE (MUSIC SCAN) SWITCH, TACTILE (PEAK SEARCH) SWITCH, TACTILE (EDIT/TIME) SWITCH, TACTILE (PLAY MODE) SWITCH, TACTILE (REPEAT) SWITCH, TACTILE (TIME) SWITCH, TACTILE (·) SWITCH, TACTILE (P) SWITCH, TACTILE (p) SWITCH, TACTILE (ENTER) SWITCH, TACTILE (CLEAR) SWITCH, TACTILE (CHECK) SWITCH, TACTILE ()) SWITCH, TACTILE (0) SWITCH, TACTILE (§ OPEN/CLOSE)

M151 A-4604-363-A MOTOR (L) ASSY (LOADING) ************************************************************** ACCESSORIES & PACKING MATERIALS ******************************** 1-467-880-11 REMOTE COMMANDER (RM-D420) (XE500) 1-558-271-11 CORD, CONNECTION 3-810-322-11 MANUAL, INSTRUCTION (ENGLISH,FRENCH,SPANISH,CHINESE) (E,AUS,CH) 3-810-322-21 MANUAL, INSTRUCTION (ENGLISH) (US) 3-810-322-31 MANUAL, INSTRUCTION (ENGLISH,FRENCH,SPANISH) (UK) 3-810-322-51 MANUAL, INSTRUCTION (GERMAN) (G) 3-810-322-61 MANUAL, INSTRUCTION (SWEDISH,FINNISH) (AEP) 3-810-322-71 MANUAL, INSTRUCTION (ENGLISH,RUSSIAN,POLISH) (EE) 3-948-574-01 SHEET (ROLL), PROTECTION (AEP,UK,G,EE) 4-962-615-01 COVER, BATTERY (FOR REMOTE COMMANDER) (XE500) 4-979-603-01 4-979-603-21 4-979-603-31 4-979-604-01 4-979-605-11 INDIVIDUAL CARTON (XE400) INDIVIDUAL CARTON (XE500:US,AUS) INDIVIDUAL CARTON (E,CH) CUSHION (US,E,AUS,CH) INDIVIDUAL CARTON (AEP,UK,G,EE)

1-473-452-11 ENCODER, ROTARY ( AMS ±) < VIBRATOR > *

X501 1-577-082-11 VIBRATOR, CERAMIC (4MHz) ************************************************************** * 1-658-840-11 POWER SW BOARD **************** < SWITCH > ! S801 1-554-118-00 SWITCH, PUSH (1 KEY) (POWER) ************************************************************** * * * * *

* 4-979-606-01 CUSHION (AEP,UK,G,EE) **************************************************************

The components identified by mark ! or dotted line with mark. ! are critical for safety. Replace only with part number specified.

36

Ref. No.

Part No.

Description ************** HARDWARE LIST **************

Remark

#1 #2 #3 #4 #5

7-685-646-79 7-682-548-04 7-621-775-10 7-621-255-15 7-685-134-19

SCREW +BVTP 3X8 TYPE2 N-S SCREW +BVTT 3X8 (S) SCREW +B 2.6X4 SCREW +P 2X3 SCREW +BTP 2.6X8 TYPE2 N-S

37

CDP-XE400/XE500

Sony Corporation
9-960-515-11
Consumer A&V Products Company Home A&V Products Div.

38

English 96B0491-1 Printed in Japan C1996.2 Published by Home A&V Products Div. Quality Engineering Dept.