Text preview for : Yamaha-CDS1000 cd.pdf part of Yamaha CDS1000 cd



Back to : Yamaha-CDS1000 cd.part1.r | Home

SUPER AUDIO CD PLAYER




CD-S1000
CD-S1000 SERVICE MANUAL




IMPORTANT NOTICE
This manual has been provided for the use of authorized YAMAHA Retailers and their service personnel.
It has been assumed that basic service procedures inherent to the industry, and more specifically YAMAHA Products, are already
known and understood by the users, and have therefore not been restated.
WARNING: Failure to follow appropriate service and safety procedures when servicing this product may result in personal
injury, destruction of expensive components, and failure of the product to perform as specified. For these reasons,
we advise all YAMAHA product owners that any service required should be performed by an authorized
YAMAHA Retailer or the appointed service representative.
IMPORTANT: The presentation or sale of this manual to any individual or firm does not constitute authorization, certification or
recognition of any applicable technical capabilities, or establish a principle-agent relationship of any form.
The data provided is believed to be accurate and applicable to the unit(s) indicated on the cover. The research, engineering, and
service departments of YAMAHA are continually striving to improve YAMAHA products. Modifications are, therefore, inevitable
and specifications are subject to change without notice or obligation to retrofit. Should any discrepancy appear to exist, please
contact the distributor's Service Division.
WARNING: Static discharges can destroy expensive components. Discharge any static electricity your body may have
accumulated by grounding yourself to the ground buss in the unit (heavy gauge black wires connect to this buss).
IMPORTANT: Turn the unit OFF during disassembly and part replacement. Recheck all work before you apply power to the unit.




I CONTENTS
TO SERVICE PERSONNEL ...................................... 2­3 DISPLAY DATA ........................................................... 25
PREVENTION OF ELECTROSTATIC DISCHARGE .... 4 IC DATA ................................................................. 26­28
FRONT PANEL .............................................................. 5 PIN CONNECTION DIAGRAMS ............................ 29­30
REAR PANELS .......................................................... 5­7 BLOCK DIAGRAM ....................................................... 31
REMOTE CONTROL PANEL ........................................ 8 PRINTED CIRCUIT BOARDS ................................ 32­40
SPECIFICATIONS / ...................................... 8­9 SCHEMATIC DIAGRAMS ...................................... 41­45
INTERNAL VIEW ........................................................... 9 REPLACEMENT PARTS LIST .............................. 47­56
DISASSEMBLY PROCEDURES ........... 10­16 REMOTE CONTROL .................................................... 57
TEST MODE / .......................................... 17
UPDATING FIRMWARE /
............................................................................ 18­24




101092 Copyright © 2008 All rights reserved.
This manual is copyrighted by YAMAHA and may not be copied or
redistributed either in print or electronically without permission.
P.O.Box 1, Hamamatsu, Japan
'08.05
CD-S1000



I TO SERVICE PERSONNEL AC LEAKAGE
1. Critical Components Information WALL EQUIPMENT TESTER OR
Components having special characteristics are marked s OUTLET UNDER TEST EQUIVALENT
CD-S1000




and must be replaced with parts having specifications equal
to those originally installed.
2. Leakage Current Measurement (For 120V Models Only)
When service has been completed, it is imperative to verify
that all exposed conductive surfaces are properly insulated INSULATING
TABLE
from supply circuits.
G Meter impedance should be equivalent to 1500 ohms shunted G Leakage current must not exceed 0.5mA.
by 0.15µF. G Be sure to test for leakage with the AC plug in both polarities.


WARNING: CHEMICAL CONTENT NOTICE!
This product contains chemicals known to the State of California to cause cancer, or birth defects or other reproductive
harm.
DO NOT PLACE SOLDER, ELECTRICAL/ELECTRONIC OR PLASTIC COMPONENTS IN YOUR MOUTH FOR ANY
REASON WHAT SO EVER!
Avoid prolonged, unprotected contact between solder and your skin! When soldering, do not inhale solder fumes or expose
eyes to solder/flux vapor!
If you come in contact with solder or components located inside the enclosure of this product, wash your hands before
handling food.

About lead free solder /
All of the P.C.B.s installed in this unit and solder joints are
soldered using the lead free solder.
Among some types of lead free solder currently available,
it is recommended to use one of the following types for the
repair work.
· Sn + Ag + Cu (tin + silver + copper)
· Sn + Cu (tin + copper)
· Sn + Zn + Bi (tin + zinc + bismuth)

Caution:
As the melting point temperature of the lead free solder is
about 30°C to 40°C (50°F to 70°F) higher than that of the lead
solder, be sure to use a soldering iron suitable to each solder.


WARNING: Laser Safety
This product contains a laser beam component. This component may emit invisible, as well as visible radiation,
which may cause eye damage. To protect your eyes and skin from laser radiation, the following precautions must be
used during servicing of the unit.
1) When testing and/or repairing any component within the product, keep your eyes and skin more than 30 cm away from
the laser pick-up unit at all times. Do not stare at the laser beam at any time.
2) Do not attempt to readjust, disassemble or repair the laser pick-up, unless noted elsewhere in this manual.
3) CAUTION : Use of controls, adjustments or performance of procedures other than those specified herein may result in
hazardous radiation exposure.


Laser Emitting conditions:
1) When the top cover is removed, and the STANDBY/ON SW is turned to the "ON" position, the laser component will emit
a beam for several seconds to detect if a disc is present. During this time (5-10 sec.) the laser may radiate through the
lens of the laser pick-up unit. Do not attempt any servicing during this period!
If no disc is detected, the laser will stop emitting the beam. When a disc is loaded, you will not be exposed to any laser
emissions.
2) The laser power level can be adjusted with the VR on the pick-up PWB, however, this level has been set by the factory
prior to shipping from the factory. Do not adjust this laser level control unless instruction is provided elsewhere in this
manual. Adjustment of this control can increase the laser emission level from the device.

2
CD-S1000




Laser Diode Properties




CD-S1000
· Material: · Laser Output:
SA-CD Semiconductor laser (AlGaInP) SA-CD 5 mW (max.)
CD Semiconductor laser (AlGaAs) CD 7 mW (max.)
· Wavelength:
SA-CD 650 nm
CD 780 nm




CAUTION - VISIBLE AND / OR INVISIBLE LASER RADIATION WHEN OPEN.
AVOID EXPOSURE TO BEAM.
VARNING - SYNLIG OCH / ELLER OSYNLIG LASERSTRÅLNING NÄR DENNA
DEL ÄR ÖPPNAD. STRÅLEN ÄR FARLIG.
VARO ! AVATTAESSA OLET ALTTIINA NÄKYVÄLLE JA / TAI
NÄKYMÄTÖMÄLLE LASERSÄTEILYLLE. ÄLÄ KATSO SÄTEESEEN.
VARNING - SYNLIG OCH / ELLER OSYNLIG LASERSTRÅLNING NÄR DENNA DEL
ÄR ÖPPNAD. BETRAKTA EJ STRÅLEN.
VORSICHT ! SICHTBARE UND / ODER UNSICHTBARE LASERSTRAHLUNG
WENN ABDECKUNG GEÖFFNET. NICHT DEM STRAHL AUSSETZEN.
ATTENTION - PADIATION VISIBLE ET / OU INVISIBLE LORSQUE L'APPAREIL
EST OUVERT. EVITEZ TOUTE EXPOSITION AU FAISCEAU.




B, G models

CAUTION - CLASS 1M LASER RADIATION WHEN OPEN
DO NOT VIEW DIRECTLY WITH OPTICAL INSTRUMENTS.




Warning for power supply
The primary side of the power supply carries live mains voltage when the player is connected to the mains even when
the player is switched off !
This primary area is not shielded so it is possible to accidentally touch copper tracks and/or components when servicing the
player.
Service personnel have to take precautions to prevent touching this area or components in this area.

Note:
The screws on the DVD mechanism may never be touched, removed or re-adjusted.
Handle the DVD mechanism with care when the unit has to be exchanged!
The DVD mechanism is very sensitive for dropping or giving shocks.

3
CD-S1000



I PREVENTION OF ELECTROSTATIC DISCHARGE
Some semiconductor (solid state) devices can be damaged easily by static electricity. Such components commonly are called
Electrostatically Sensitive (ES) Devices. Examples of typical ES devices are integrated circuits and some field-effect transis-
CD-S1000




tors and semiconductor "chip" components. The following techniques should be used to help reduce the incidence of compo-
nent damage caused by electro static discharge (ESD).
1. Immediately before handling any semiconductor component or semiconductor-equipped assembly, drain off any ESD on
your body by touching a known earth ground. Alternatively, obtain and wear a commercially available discharging ESD wrist
strap, which should be removed for potential shock reasons prior to applying power to the unit under test.
2. After removing an electrical assembly equipped with ES devices, place the assembly on a conductive surface such as
aluminum foil, to prevent electrostatic charge buildup or exposure of the assembly.
3. Use only a grounded-tip soldering iron to solder or unsolder ES devices.
4. Use only an anti-static solder removal device. Some solder removal devices not classified as "anti-static (ESD protected)"
can generate electrical charge sufficient to damage ES devices.
5. Do not use freon-propelled chemicals. These can generate electrical charges sufficient to damage ES devices.
6. Do not remove a replacement ES device from its protective package until immediately before you are ready to install it. (Most
replacement ES devices are packaged with leads electrically shorted together by conductive foam, aluminum foil or compa-
rable conductive material).
7. Immediately before removing the protective material from the leads of a replacement ES divice, touch the protective mate-
rial to the chassis or circuit assembly into which the device will be installed.
CAUTION: Be sure no power is applied to the chassis or circuit, and observe all other safety precautions.
8. Minimize bodily motions when handling unpackaged replacement ES devices. (Otherwise harmless motion such as brush-
ing together of your fabric clothes or lifting of your foot from a carpeted floor can generate static electricity (ESD) sufficient
to damage an ES device).


Grounding for electrostatic breakdown prevention
1. Human body grounding.
Use the antistatic wrist strap to discharge the static electricity from your body.
2. Work table grounding.
Put a conductive material (sheet) or steel sheet on the area where the optical pickup is placed and ground the sheet.


Caution:
The static electricity of your clothes will not be grounded through the wrist strap. So take care not to let your clothes touch the
optical pickup.




Anti-static wrist strap
1M-ohms
Conductive material
(sheet) or steel sheet




4
CD-S1000



I FRONT PANEL
CD-S1000 (U, C, R, T, K, A, B, G, L, J models)




CD-S1000
I REAR PANELS
CD-S1000 (U, C models)




CD-S1000 (R model)




5
CD-S1000




CD-S1000 (T model)
CD-S1000




CD-S1000 (K model)




CD-S1000 (A model)




6
CD-S1000




CD-S1000 (B, G models)




CD-S1000
CD-S1000 (L model)




CD-S1000 (J model)




7
CD-S1000



I REMOTE CONTROL PANEL I SPECIFICATIONS /
CDX5 I Audio Section /
Frequency Response /
CD-S1000




SA-CD .......................................................... 2 Hz to 50 kHz (-3 dB)
CD ............................................................................. 2 Hz to 20 kHz
Total Harmonic Distortion (1 kHz) /
................................................................................. 0.002 % or less
Signal to Noise Ratio / (IHF-A Network)
................................................................................. 113 dB or more
Dynamic Range /
SA-CD ...................................................................... 105 dB or more
CD ............................................................................ 100 dB or more
Output Level (1 kHz, 0 dB) /
........................................................................................ 2.0 ± 0.3 V

I General /
Power Supply /
U, C models .......................................................... AC 120 V, 60 Hz
R, L models ........................ AC 110/120/220/230-240 V, 50/60 Hz
T model ................................................................. AC 220 V, 50 Hz
K model ................................................................. AC 220 V, 60 Hz
A model ................................................................. AC 240 V, 50 Hz
B, G models .......................................................... AC 230 V, 50 Hz
J model ........................................................... AC 100 V, 50/60 Hz
Power Consumption
U, C, R, T, K, A, B, G, L models ............................................. 30 W
J model .................................................................................... 25 W
Off-state Power Consumption
................................................................................................... 0 W
Dimensions (W x H x D)
.......................... 435 x 137 x 440 mm (17-1/8" x 5-3/8" x 17-5/16")
Weight
......................................................................... 15 kg (33 lbs. 1 oz.)
Finish
Black color ................................ U, C, R, T, K, A, B, G, L, J models
Silver color ................................ U, C, R, T, K, A, B, G, L, J models
Accessories
Remote control x 1, Battery (R6, AA, UM-3) x 2, Audio pin cable (1.5 m)
x 1, Power cable (2 m) x 1


* Specifications are subject to change without notice due to product
improvements.




U .......... U.S.A. model A .......... Australian model
C .......... Canadian model B .......... British model
R .......... General model G .......... European model
T .......... Chinese model L .......... Singapore model
K .......... Korean model J ........... Japanese model




8
CD-S1000




(5/16")
· DIMENSIONS /




8




CD-S1000
418 (16-7/16")

440 (17-5/16")
362 (14-1/4")

14
(9/16")
120 (4-3/4")

137 (5-3/8")
17
(11/16")
371 (14-5/8")
Unit: mm (inch)
435 (17-1/8")




I INTERNAL VIEW
1 2 3 4 5 6 1 POWER TRANSFORMER
2 POWER (2) P.C.B. (R, L models)
3 POWER (1) P.C.B.
4 LOADER UNIT
5 AUDIO P.C.B.
6 DIGITAL (1) P.C.B.
7 DIGITAL (5) P.C.B.
8 POWER (3) P.C.B.
9 DIGITAL (4) P.C.B.
0 DIGITAL (3) P.C.B.
A DIGITAL (2) P.C.B.




8 7
9 0 A




9
CD-S1000



I DISASSEMBLY PROCEDURES /
(Remove parts in the order as numbered.)
Disconnect the power cable from the AC outlet.
CD-S1000




1. Removal of Panel Side L/R
a. Remove 2 screws (1), coned disc spring L and washer 1
side. (Fig. 1)
b. Lift the panel side L a little, release hooks at 3 locations
and then remove the panel side L. (Fig. 1)
c. Remove 2 screws (2) and then remove 2 washers. 2
(Fig. 1)
d. Lift the panel side R a little, release hooks at 3 loca-
tions and remove the panel side R. (Fig. 1)

2. Removal of Top Cover
a. Remove 7 (U, C models) / 5 (R, T, K, A, B, G, L models) 3 4 5
screws (3), 2 screws (4) and 2 screws (5). (Fig. 1)
b. Remove the top cover. (Fig. 1)




Panel side L

Top cover

Coned disc spring L
Hook



3
1 4 5
3

Hook
3 U, C models
Washer side
3
Panel side R

"POWER ON / OFF" switch




Hook
7



7 Coned disc spring L


Lid Front panel
2
Washer side
6


Fig. 1




10
CD-S1000




3. Removal of Front Panel
a. Using a flatblade screwdriver, move the slider at the bot-




CD-S1000
tom in the direction of the arrow shown below. (Fig. 2)
* Tray lock will be released but will not come out.
b. Push out the tray by pushing its rear. (Fig. 3)
c. Using a phillips screwdriver, remove 2 screws (6) and 6
then remove the lid. (Fig. 1)
d. Close the tray by pushing its front.
e. Remove 8 screws (7). (Fig. 1) 7
f. Set the "POWER ON/OFF" switch to the ON position.
g. Remove the front panel forward gradually, using care
not to cause any damage to the "POWER ON/OFF"
switch. (Fig. 1)




Flatblade screwdriver



Fig. 2




Tray




Fig. 3




11
CD-S1000




4. Removal of Front Frame ass'y
a. Remove 4 screws (8), 2 screws (9) (B, G models) and 8 9
CD-S1000




then remove the frame top. (Fig. 4)
b. Remove 9 screws (0). (Fig. 4) 0
c. Remove CB601 and CB902. (Fig. 4)
d. Remove the front frame ass'y. (Fig. 4)

5. Removal of AUDIO P.C.B.
a. Remove 6 screws (A). (Fig. 4) A
b. Remove 4 screws (B). (Fig. 5) B
c. Remove CB1-2 and CB5-6. (Fig. 4)
* When installing CB5 and CB6, be sure to con-
nect the Blue/Black color cable to CB5 and the
Red/Black cable to CB6. Both connectors have
same shape.
d. Lift the front of AUDIO P.C.B. and then remove it. (Fig. 4)



8
Frame top


9
8 (B, G, J models)
Frame mecha L Loader unit
AUDIO P.C.B.
E
G
A CB1
CB2
A
CB5
F C
Support AUDIO

CB6
Frame mecha R



Push rivet


Support F D



Front frame ass'y CB612


CB301
CB601 C
D CB302
0




CB903 CB902
0
Support F Push rivet

0
0

Fig. 4

12
CD-S1000




B 6. Removal of Loader Unit
a. Remove 4 screws (C) and then remove the support C
audio. (Fig. 4)
b. Remove CB301-302, CB612 and CB903. (Fig. 4)
c. Remove 4 screws (D). (Fig. 4) D
d. Remove 2 push rivets and then remove support F on
both sides of the loader unit. (Fig. 4)
e. Remove 2 screws (E) and then the frame mecha L. E
(Fig. 4)
f. Remove 2 screws (F) and then remove the frame F
mecha R. (Fig. 4)
g. Remove 2 screws (G) and then remove the loader G
Fig. 5
unit. (Fig. 4)

G When installing the Loader Unit:
When installing the loader unit, adjust the clearance be-
tween the front panel and lid so that it becomes equal at
the top, bottom, right and left.
1. Loosen 2 screws (H) and 2 screws (I). (Fig. 7) H I
When checking the AUDIO P.C.B.:
2. Position the support F on both sides with its flat
· Put the rubber sheet and cloth over this unit. Then portion facing upward. (Fig. 7)
place the P.C.B.s upside down on the cloth and 3. Viewing from the front, confirm the lid position. (Fig. 7) I
check it. (Fig. 6) 4. Tighten the screws on the side with higher lid inclina-
· Reconnect all cables (connectors) that have been tion (screws (I) in the case shown below). (Fig. 7)
disconnected. 5. Turn the support F on the side with lower lid inclina-
Use to use the extension cable before connection the tion clockwise gradually until the lid is positioned
following connectors. horizontally. (Fig. 7) H
AUDIO P.C.B. CB2­DIGITAL P.C.B. CB303 6. With the lid adjusted at the horizontal position,
12P, 450mm P=1.25 (MF112450) tighten other screws (screws (H) in the case I
· When connecting the flexible flat cable, be careful shown below). (Fig. 7) To change the position up-
with polarity. ward at this time, loosen screws (I) and then turn
· In this unit, the ground of P.C.B.s shown below is the support F clockwise gradually.
connected to the rear panel and chassis. When these * Be sure to make adjustment from either side only.
P.C.B.s are removed from the rear panel, connect the 7. Repeat opening and closing the tray some times
ground point to the rear panel or chassis, using a and confirm to make sure that the same clearance
ground lead wire or the like. (Fig. 6) between the front panel and lid is obtained at the
top, bottom, right and left.

H Flat portion

AUDIO P.C.B.
Ground lead
Rubber sheet and cloth ST1

Support F H




CB2 I Flat portion
FG

DIGITAL P.C.B.
MF112450
Support F I
CB303 Lid




Ground lead


Fig. 6
Fig. 7
13
CD-S1000




7. Removal of DIGITAL P.C.B. L
R, L models
a. Remove 3 screws (J). (Fig. 8) J
b. Remove 4 screws (K). (Fig. 9) K
c. Remove CB610-611 and CB901. (Fig. 8)
d. Remove the DIGITAL P.C.B.. (Fig. 8)

8. Removal of POWER (2) P.C.B.
M
(R and L models)
N O
a. Remove 2 screws (L). (Fig. 9)
b. Remove the POWER (2) P.C.B.. (Fig. 8)
K N O
9. Removal of POWER (1) P.C.B.
c. Remove 4 screws (M). (Fig. 8) Fig. 9
b. Remove 2 screws (N) and 2 screws (O). (Fig. 9)
c. Remove CB603, CB606-607, CB615 and CB604 (R, L
models). (Fig. 8)
d. Remove the POWER (1) P.C.B.. (Fig. 8)

G Disassembly of Loader Unit

1. Removal of Module Board
POWER (2) P.C.B. (R, L models) a. Remove CN102 and CN103. (Fig. 10) 10
b. Unlock CN101 and then disconnect the flexible flat
POWER (1) P.C.B. cable, and ground the terminal face of the flexible
M
flat cable with a clip or the like. (Fig. 10) 10
CB603
c. Remove 5 screws (P). (Fig. 10) P 10
CB607 CB610 d. Remove the module board. (Fig. 10) 10
M

DIGITAL P.C.B.
CB604 (R, L models) J

Locked
CB606
CB611

J
Flexible flat cable


CN101

Unlocked
Module board 13 mm
(1/2")

Flexible flat cable Terminal side


CN103
Clip

CB615
P CN101
CN102 Use a clip or other item to ground
the unit.
CN101
P
CB901

Fig. 10
Fig. 8




14
CD-S1000




2. Removal of DVD Traverse Mechanism and
Stepping Motor.




CD-S1000
* When installing a new DVD traverse mecha-
nism, remove the solder from the shorted
point of pick up unit using an electrostatic
shielding soldering iron.
a. Remove 6 screws (Q) and then remove the clamp Q
ass'y. (Fig. 11)
b. Push out the tray by pushing its rear. (Fig. 11)
c. Remove 2 screws (R). (Fig. 11)
d. Remove the DVD traverse mechanism together R
with the holder PU/SA-CD. (Fig. 11)
e. Remove 4 screws (S) and then remove the DVD
traverse mechanism. (Fig. 11) S
f. Remove 2 screws (T) and then remove the step-
ping motor. (Fig. 11) T




Clamp ass'y T Stepping motor


Q Q
S


DVD traverse mechanism

R



Holder PU/SA-CD




Tray




Fig. 11




15
CD-S1000




· When installing a new Stepping Motor:
Before installing a new stepping motor, apply
CD-S1000




grease to its screw.
Recommended grease:
PN-397 (Part No.: AAX89650)
a. Apply grease to the screw at 3 points as shown
below. (Fig. 12)
* Amount of grease to be applied:
3mg ± 1mg at 3 points
b. After applying grease, spread it evenly between
A and B of the screw of the stepping motor.
(Fig. 13)
* While spreading grease evenly, use full
care not to cause damage to the screw.
* If waste thread, dust, etc. is attached, re-
move it.
c. Apply grease to the DVD traverse mechanism
as shown below. (Fig. 14)
* Amount of grease to be applied:
2 mg ± 1mg at 1 point

· Operation check after installing a new stepping
motor
After installing all parts, turn on the power and
check for proper operation.
1. Load CD, repeat the search function between
the first number and the last one some times so
that the grease is settled.
2. Perform random playback and check for proper
operation.




Fig. 12




Fig. 13




Fig. 14


16
CD-S1000



I TEST MODE /
G Starting Test Mode




CD-S1000
To activate the TEST mode, set the "POWER ON/
OFF" switch to the ON position while pressing the
keys of this unit as shown below at the same time.




"POWER ON/OFF" switch "PLAY" key "STOP" key


When the power is ON Starting TEST mode




T E S T X0012
Release the "PLAY" and "STOP keys.


Firmware version of microprocessor is displayed. /




G Operating Test Mode
Press the "DISPLAY" key on the remote control, and
the display changes in the order as shown below.


Initial display /
T E S T X0012

The firmware version of the module board is displayed. /
7 1 6 2 1_14
The firmware version /


The firmware version of the microprocessor and its updated data are displayed. /
X0012 071001
The firmware version / The updating data /


All segments ON (dimmer 100 %) /
TEST X0012

All segments OFF /
TEST X0012

(Not applied to this model / )
XXXXXXXXXX

17
CD-S1000



I UPDATING FIRMWARE /
Writing to the microprocessor
CD-S1000




After replacing the following parts update the latest firm-
ware according to the following procedure.

DIGITAL P.C.B.
Microprocessor (IC302) of DIGITAL P.C.B.



G Required tools
· Program downloader programs
................................................... FlashSta.exe
· Firmware
.................................................. CDS1000xx.S
................................................. CDS1000xx.id
· RS232C cross cable "D-sub 9 pin female"
(Specifications)




· RS232C conversion jig (Part No.: AAX88050)

G Preparation and precautions before starting
the operation
· Download firmware downloader program and
firmware from the specified source to the same
folder of the PC.
· Prepare the above specified RS232C cross
cable.
· While writing, keep the other application software
on the PC closed.
It is also recommended to keep the software on
the task tray closed as well.




18
CD-S1000




CD-S1000
G Operation Procedures
1. Turn off the power of this unit and disconnect the
power cable from the AC outlet.
2. Remove 2 screws (1). (Fig. 1) 1
3. Lift the panel side R a little, release hooks at 3 loca-
tions and then remove the panel side R. (Fig. 1)
4. Connect the writing port of this unit to the serial port
(RS232C) of the PC with RS232C cross cable, RS232C
conversion jig and flexible flat cable as shown below.
(Fig. 1)



Writing port




Flexible flat cable 8P



Hook Reset switch


RS232C conversion jig



RS232C cross cable
Panel side R
Coned disc spring L


1
Washer side




"POWER ON/OFF" switch



Fig. 1



5. Connect the power cable of this unit to the AC outlet.
(Fig. 1)
6. While pressing the reset switch of RS232C conver-
sion jig, set the "POWER ON/OFF" switch of this unit
to the ON position. (Fig. 1)
19
CD-S1000
CD-S1000




7. Start up FlashSta.exe, the screen will appear as
shown below. (Fig. 2)




Select Internal flash memory




Select the port of RS-232C




Fig. 2




8. Select the port and data to be transmitted. (Fig. 2)
· Select Program
Select Internal flash memory
· RS232C
Select the port of RS-232C
* For selection of the port, COM1 to 4 can be
used.
As COM5 or higher port cannot be used, select
out of COM 1 to 4 of the setting on the PC side.
9. Click [Refer...]. And select the firmware name. (Fig. 3)

* The ID code and MCU type are
loaded automatically when the
file is selected. (Fig. 3)
Click [OK]. (Fig. 3)




Click to open the window




Fig. 3




20
CD-S1000




CD-S1000
10. Click [E.P.R.], the screen appears as shown below.
(Fig. 4)
Click [OK] to start writing. (Fig. 4)




Writing being executed.




Fig. 4



11. When the program transmission is completed, the
screen appears as shown below. (Fig. 5)
Click [OK] to end the procedure. (Fig. 5)




Fig. 5




21
CD-S1000
CD-S1000




12. Set the "POWER ON/OFF" switch of this unit to the
OFF position.
13. Disconnect the power cable of this unit from the AC
outlet.
14. End "FlashSta. exe."
15. Disconnect the RS232C cross cable, RS232C conver-
sion jig and flexible flat cable.

· Confirmation of firmware version
Confirm the firmware is updated successfully from the
test mode.
For more information, refer to "TEST MODE".

1. Connect the power cable of this unit to the AC outlet.
2. While pressing the "PLAY" and "STOP" keys of this
unit, set the "POWER ON/OFF" switch to the ON posi-
tion. Test mode is activated. (Fig. 6)
3. Press the "DISPLAY" key on the remote control, select
the function to display the firmware version of the mi-
croprocessor. Check that the displayed firmware ver-
sion is the same as written firmware version.




Key of this unit /

Set the "POWER ON/OFF" switch to the
ON position while pressing these keys.




"POWER ON/OFF" switch "PLAY" key "STOP" key


The updating data /


X0012 071001
The firmware version /



Fig. 6



* When the displayed firmware version is different
from written firmware version, follow the steps
from 1 to 15 of operation procedures again.


22
CD-S1000




Writing to the Module Board




CD-S1000
After replacing the Module board with the replacement part,
be sure to write the latest firmware.

G Required Tools
Firmware CD
* To make the firmware CD, download the latest firm-
ware from the specified download source to PC.
Firmware: S5JAxxx6.BIN


G Operation Procedures
CAUTION: Do not turn off the power while updat-
ing the firmware.
1. Connect the power cable of this unit to the AC out-
let.
2. Set the "POWER ON/OFF" switch of this unit to
the ON position. (Fig. 7)
3. Press the "OPEN/CLOSE" key of this unit to open
the tray. (Fig. 7)




"POWER ON/OFF" switch "OPEN/CLOSE" key "PLAY" key



Fig. 7



4. Put the firmware CD on the tray and close the
tray.
Then "UPGRADE?" is displayed.



UPGRADE?

5. Press the "PLAY" key of this unit, and then writing
of the firmware is started and "UPGRADE" flashes.



Flashing /




23
CD-S1000
CD-S1000




6. After about 5 seconds, the tray opens automati-
cally.
Remove the firmware CD.
* At this time, do not turn off the power as writ-
ing of the firmware is going on in this unit.
* Writing takes about 1 minute.
7. When writing is completed, the tray closes auto-
matically.
8. After "NO DISC" is displayed, set the "POWER
ON/OFF" switch to the OFF position.

· Confirmation of firmware version
Confirm the firmware is updated successfully from the
test mode.
For more information, refer to "TEST MODE".
1. Connect the power cable of this unit to the AC outlet.
2. While pressing the "PLAY" and "STOP" keys of this
unit, set the "POWER ON/OFF" switch to the ON posi-
tion. Test mode is activated. (Fig. 8)
3. Press the "DISPLAY" key on the remote control, select
the function to display the firmware version of the mod-
ule board. Check that the displayed firmware version is
the same as written firmware version.




Key of this unit /

Set the "POWER ON/OFF" switch to the ON position while pressing these keys.




"POWER ON/OFF" switch "PLAY" key "STOP" key




7 1 6 2 1_14
The firmware version /



Fig. 8



* When the displayed firmware version is different
from written firmware version, follow the steps
from 1 to 8 of operation procedures again.


24
CD-S1000



I DISPLAY DATA
G V800 : 13-ST-81GINK (DIGITAL (2) P.C.B.)