Text preview for : AW4416_SM2_E.pdf part of Yamaha AW4416 sound workstation
Back to : Yamaha-AW4416 workstation | Home
AW4416
HARD DISK INSTALLATION
· Hard disks are precision devices. Do not subject them to physical shock or static electricity, etc. · Do not place a hard disk nearby devices that produce a strong magnetic field, or in locations of extreme cold, heat, or moisture. · Before you handle a hard disk, touch your hand to a grounded metallic object to release any static charge that may be present in your body or clothing. If you fail to do so, static electricity may damage the hard disk. · Never attempt to disassemble a hard disk or apply excessive force to it. · The AW4416 is shipped with four screws for attaching a 2.5 inch hard disk, and four screws for attaching a CD-RW drive, making a total of eight included screws of the same type. 1. You will need the following items. · The AW4416 itself · A 2.5 inch IDE hard disk (sold separately) for installation · Four screws included with the AW4416 for attaching the 2.5 inch hard disk (Pan washer head screw 3.0 X 4 VS676500) · A philips (+) screwdriver 2. Make sure that the power of the AW4416 is turned off. For safety's sake, disconnect the power cable from the AC outlet. 3. On the rear panel of the AW4416, remove the two screws that hold the ADP25H (PN-HDD circuit board) 2.5 inch hard disk adapter to the 2.5" HARD DISK DRIVE slot.
ADP25H (2.5 inch hard disk adapter)
35
AW4416
4. Place the hard disk on the ADP25H (PN-HDD circuit board) as shown in the diagram below, align the screw holes of the hard disk and the ADP25H (PN-HDD circuit board), and use your screwdriver to fasten the screws at the four locations shown.
Flat cable
5. Plug the connector of the flat cable (HDD cable assembly VS580600) extending from the ADP25H (PN-HDD circuit board) into the connector of the hard disk.
Flat cable connector
· Even if it is difficult to plug in the connector, do not use excessive pressure to force it in. This may damage the hard disk, or you may injure yourself.
36
AW4416
6. Aligning the ADP25H (with the hard disk attached) with the rails inside the 2.5" HARD DISK DRIVE slot, push it in until it clicks into place. 7. Use the screws that you removed in step 3 to fasten the ADP25H into the 2.5" HARD DISK DRIVE slot.
If you fail to tighten the screws all the way, the hard disk may vibrate and fail to operate correctly.
· Do not turn on the power of the AW4416 until all options have been installed. · When you turn on the power of the AW4416 after installing a new hard disk, formatting of the hard disk will begin automatically.
CD-RW DRIVE INSTALLATION
The SCSI ID of the CD-RW drive
· The SCSI ID of the AW4416 itself is fixed at "6." For this reason, you must set the SCSI ID of the CD-RW drive to "6" before installing it. · In the various screens of the AW4416, the SCSI ID of the internal CD-RW drive has been set to "3" by default. For this reason, you will find it conve-nient to set the ID of the CD-RW to "3." (For details on setting the SCSI ID, refer to the manual for your CD-RW drive.) · If you are installing a CD-RW drive manufactured by Yamaha, the SCSI ID will be set to "3" at the factory, and we recommend that you leave it at this setting.
37
AW4416
Installation procedure
1. You will need the following items. · The AW4416 itself · Internal CD-RW drive (option) · Screws (included with the AW4416) for attaching the CD-RW drive (Pan washer head screw 3.0 X 4 VS676500) · Red and white four conductor cable for CD-RW drive (Connector assembly V564820) · Philips (+) screwdriver · Work surface
· In order to install the CD-RW drive you will need to turn the AW4416 on itsback. Make sure that you have a sufficiently broad work surface. · The AW4416 is shipped with four screws for attaching the 2.5 inch hard disk, and four screws for attaching the CD-RW drive, making a total of eight screws of the same type.
2. Make sure that the power of the AW4416 is turned off. For safety's sake, disconnect the power cable from the AC outlet. 3. Turn the AW4416 upside down on the work surface.
38
AW4416
When turning the AW4416 upside down, we recommend that you use thepack-ing foam from the AW4416's shipping carton as shown in the diagram at above, so that the controls of the top panel are not damaged. If the packing foam is not available, please spread out a soft cloth, and support each of the four corners of the AW4416 with a stack of magazines etc.
4. Remove the CD-RW drive cover from the front panel, and remove the connector cover.
Connector cover CD-RW drive cover
5. Turn the CD-RW drive over, and insert it little by little, stopping whenthe connector end of the CD-RW drive enters the opening in the bottom of the AW4416.
39
AW4416
6. Connect the red and white four-conductor cable (Connector assembly V564820) included with the AW4416 to the internal connector of the AW4416 as shown in the dia-gram. Then connect the cable to the connector of the CD-RW drive.
7.
Plug the connector of the flat cable (Connector assembly V564700) extending from inside the AW4416 into the connector of the CD-RW drive.
8. Align the screw holes in the bottom of the CD-RW drive with the screw holes of the AW4416, and use a screwdriver to fasten the drive with the four included screws.
40
AW4416
9. Re-attach the CD-RW drive cover and the connector cover that you removed in step 3. At this time, remove the CD-RW plate from the CD-RW drive cover.
Connector cover
CD-RW drive cover
CD-RW plate
I/O CARD INSTALLATION
1. Make sure that the power of the AW4416 is turned off. For safety's sake, disconnect the power cable from the AC outlet. 2. From the OPTION I/O slot located on the rear panel of the AW4416, remove the two screws (Bind head screw 4.0 X 2 VB132700) that hold the cover in place.
41
AW4416
Please keep the cover and screws you removed in a safe place.
3. Slide the I/O card along the rails inside the slot until it clicks into place. 4. Tighten the two screws included with the I/O card to fasten the card securely.
Please note that if the screws are loose, the card may not be grounded correctly.
42
AW4416
LSI PIN DESCRIPTION
M66004FP (XT828A00) Display Driver ................................ 43 HD6437042AF28 (XY715A00) CPU HD6437042AF53 (XY721A00) CPU HD6437042AF28 (XW647A00) CPU ..................................... 44 YSS904-F (XV989A00) DSP5 (Digital Signal Processor) .... 45 YSS910-S (XV988A00) DSP6 (Digital Signal Processor) .... 46 CI-DRC (XY629A00) Gate Array .......................................... 47 LR38791 (XY631A00) Gate Array ......................................... 48 LR38792 (XY630A00) Gate Array ......................................... 49 SPC7214F0B (XY625A00) SCSI Control .............................. 50 AK4528VF (XY624A00) ADC/DAC ........................................ 51 MBCG46183-129 (XV833A00) Gate Array ........................... 51 DS12887 (XV618A00) Real Time Clock ................................ 51 SED1335F0B (XQ595A00) LCDC (LCD Controller).............. 52 YM3436DK (XG948E00) DIR2 (Digital Format Interface Receiver) ..................................... 52 YM3437C-F (XM530A00) DIT2 (Digital Format Interface Transmitter) ................................ 53
M66004FP (XT828A00) Display Driver
PIN NAME NO. 1 DIG11 2 DIG10 3 DIG09 4 DIG08 5 DIG07 6 DIG06 7 DIG05 8 DIG04 9 DIG03 10 DIG02 11 DIG01 12 DIG00 13 /RESET /CS 14 SCK 15 16 SDATA 17 P1 18 P0 Vcc1 19 20 XOUT 21 XIN 22 Vss 23 SEG35 24 SEG34 25 SEG33 26 SEG32 27 SEG31 28 SEG30 29 SEG29 30 SEG28 31 SEG27 32 VP I/O O O O O O O O O O O O O I I I I O O O I O O O O O O O O O FUNCTION PIN NO. 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 NAME SEG26 SEG25 SEG24 SEG23 SEG22 SEG21 SEG20 SEG19 SEG18 SEG17 SEG16 SEG15 SEG14 SEG13 SEG12 SEG11 SEG10 SEG09 SEG08 SEG07 SEG06 SEG05 SEG04 SEG03 SEG02 SEG01 SEG00 Vcc2 DIG15 DIG14 DIG13 DIG12 I/O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O FUNCTION
PN-SW: IC601
Digital output
Reset Chip selection Sift clock Serial data Output port 1 Output port 0 Power supply Clock out Clock in Ground
Segment output
Segment output
Power supply Digital output
(-) Power supply
43
AW4416
HD6437042AF28 (XY715A00) CPU HD6437042AF53 (XY721A00) CPU HD6437042AF28 (XW647A00) CPU
PIN NO. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 NAME TIOC4/DACK0/PE14 PE15 VSS A0 A1 A2 A3 A4 A5 A6 A7 A8 A9 A10 A11 A12 A13 A14 A15 A16 VCC A17 VSS /RAS/PB2 /CASL/PB3 /CASH/PB4 VSS /RDWR / PB5 A18//BACK/PB6 A19//BREQ/PB7 A20/PB8 A21/PB9 VSS /RD /WDTOVF /WRH VCC /WRL VSS /CS1 /CS0
/IRQ3/TCLKD/PA9 TCLKC//IRQ2 /PA8
MAIN: IC601,803 SUB-CPU: IC301 PIN NO. 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 105 106 107 108 109 110 111 112 NAME D11 D10 D9 D8 VSS D7 D6 D5 VCC D4 D3 D2 D1 D0 VSS XTAL MD3 EXTAL MD2 NMI VCC MD1 MD0 PLLVCC PLLCAP PLLVSS PA15 / CK /RES PE0/DREQ0 PE1/DRAK0 PE2 PE3 PE4 VSS PF0 / AN0 PF1 / AN1 PF2 / AN2 PF3 / AN3 PF4 / AN4 PF5 / AN5 AVSS PF6 / AN6 PF7 / AN7 AVCC VSS PE5 VCC PE6 PE7 PE8 PE9 PE10 VSS PE11 PE12 /MRES I/O I/O I/O I/O I/O I I/O I/O I/O I I/O I/O I/O I/O I/O I I I I I I I I I I I I O I I/O O O O O I I I I I I I I I I I I O I I/O I/O I/O O O I O O I FUNCTION
I/O I/O O I O O O O O O O O O O O O O O O O O I O I I/O I/O I/O I I/O I/O I/O O O I O O O I O I O O I/O I/O O O I/O O I I/O O I I/O I/O I/O I I/O
FUNCTION MTU I/O / DMA acknowledge / Port E Port E Ground
Data bus Ground Data bus Power supply Data bus Ground Crystal oscillator Mode control Crystal oscillator Mode control Non-maskable interrupt request Power supply Mode control Mode control PLL Power supply PLL capacitor PLL Ground Port A / Clock Power on reset Port E / DMA request Port E / DMA acknowledge Port E Ground Port F / Analog input
Address bus
Power supply Address bus Ground Row address strobe / Port B Column address strobe (low) / Port B Column address strobe (high) / Port B Ground DRAM read / write / Port B Address bus / Bus acknowledge / Port B Address bus / Bus request / Port B Address bus/ Port B Ground Read Watch dog timer overflow High write Power supply Low write Ground Chip select Chip select Interrupt request / Timer clock/ Port A Timer clock / Interrupt request / Port A Chip select Chip select Interrupt request / Port A Data transmission Data reception Interrupt request / Port A Data transmission Data reception Data bus Ground Data bus
Analog ground Port F / Analog input Power supply Ground Port E Power supply Port E Ground Port E Manual reset
/CS3 /CS2 /IRQ1/PA5 TXD1 RXD1 /IRQ0/PA2 TXD0 RXD0 D15 D14 D13 VSS D12
44
AW4416
YSS904-F (XV989A00) DSP5 (Digital Signal Processor)
PIN NO. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 NAME NC NC NC NC Vdd Vss XI XO Vdd /SYNCI /SYNCO Vdd CKI CKO CKSEL Vss MCKD /SSYNC /IC /TEST NC NC NC Vdd Vss /CS /WR /RD CA7 CA6 CA5 CA4 CA3 CA2 CA1 Vss Vdd CD15 CD14 CD13 CD12 CD11 CD10 CD09 CD08 CD07 CD06 Vss NC NC NC NC NC NC NC NC Vdd Vdd CD05 CD04 CD03 CD02 CD01 CD00 /WAIT Vss SIO00 SIO01 SIO02 SIO03 SIO04 SIO05 SIO06 SIO07 Vss Vdd SIO08 SIO09 SIO10 SIO11 SIO12 SIO13 SIO14 SIO15 Vss Vdd SIO16 SIO17 SIO18 SIO19 SIO20 SIO21 SIO22 SIO23 Vss Vdd SIO24 SIO25 SIO26 SIO27 NC NC NC NC I/O FUNCTION Not used Ground Power supply System master clock input (60 MHz or 30 MHz) System master clock output (High or 30 MHz) Ground Sync. signal input Sync. signal output Ground System clock input (30 MHz) System clock output (30 MHz) System master clock select Power supply Serial clock input (256 fs) Serial. signal input Initial clear Test mode setting (0: TEST, 1: Normal) Not used Ground Power supply Chip select Write enable input Read enable input PIN NO. 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 128 129 130 131 132 133 134 135 136 137 138 139 140 141 142 143 144 145 146 147 148 149 150 151 152 153 154 155 156 157 158 159 160 161 162 163 164 165 166 167 168 169 170 171 172 173 174 175 176 177 178 179 180 181 182 183 184 185 186 187 188 189 190 191 192 193 194 195 196 197 198 199 200 201 202 203 204 205 206 207 208 NAME NC NC NC NC SIO28 SIO29 SIO30 SIO31 Vss Vdd SIO32 SIO33 SIO34 SIO35 SIO36 SIO37 SIO38 SIO39 Vss Vdd SIO40 SIO41 SIO42 SIO43 SIO44 SIO45 SIO46 SIO47 Vss SIO48 SIO49 SIO50 SIO51 SIO52 SIO53 SIO54 SIO55 Vss Vdd Vdd SIO56 SIO57 SIO58 SIO59 SIO60 SIO61 SIO62 SIO63 NC NC NC NC NC NC NC NC Vss /POE Vss PIO00 PIO01 PIO02 PIO03 PIO04 PIO05 PIO06 PIO07 Vss Vdd Vdd PIO08 PIO09 PIO10 PIO11 PIO12 PIO13 PIO14 PIO15 Vss NC PIO16 PIO17 PIO18 PIO19 PIO20 PIO21 PIO22 PIO23 Vss Vdd Vdd PIO24 PIO25 PIO26 PIO27 PIO28 PIO29 PIO30 PIO31 Vss NC NC NC NC I/O FUNCTION Not used I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O
MAIN: IC505,509
I O O I O I O I I I I I
Serial data bus Power supply Ground
Serial data bus
Power supply Ground
Serial data bus
I I I I I I I I I I I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O
Power supply
CPU address bus
Serial data bus
Power supply Ground
Power supply Ground I/O I/O I/O I/O I/O I/O I/O I/O
CPU data bus
Serial data bus
Power supply
Not used
Not used
Ground I/O I/O I/O I/O I/O I/O O I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O
I I/O I/O I/O I/O I/O I/O I/O I/O
Power supply Parallel data bus controll signal Power supply
CPU data bus
Parallel data bus
Wait output Power supply
Power supply Ground I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O
Serial data bus
Power supply Ground
Parallel data bus
Serial data bus
Power supply Not used
Power supply Ground
Parallel data bus
Power supply Ground I/O I/O I/O I/O I/O I/O I/O I/O
Serial data bus
Power supply Ground Serial data bus
Parallel data bus
Power supply Not used
Not used
45
AW4416
YSS910-S (XV988A00) DSP6 (Digital Signal Processor)
PIN NO.
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88
MAIN: IC301,306,308,401-403,502 I/O
Ground I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O
NAME
Vdd Vss XI XO Vdd /SYNCI /SYNCO Vdd CKI CKO CKSEL Vss MCKS /SSYNC /IC /TEST BTYP /IRQ TRIG Vdd Vss /CS /WR /RD CA7 CA6 CA5 CA4 CA3 CA2 CA1 Vss Vdd CD15 CD14 CD13 CD12 CD11 CD10 CD09 CD08 CD07 CD06 Vss Vdd Vdd CD05 CD04 CD03 CD02 CD01 CD00 /WAIT Vss SI0 SI1 SI2 SI3 SI4 SI5 SI6 SI7 Vss Vdd SO0 SO1 SO2 SO3 SO4 SO5 SO6 SO7 Vss DB00 DB01 DB02 DB03 DB04 DB05 DB06 DB07 DB08 DB09 DB10 DB11 DB12 Vdd Vdd
I/O
FUNCTION
Power supply (3.3 V) Ground System master clock input (60 MHz or 30 MHz) System master clock output (High or 30 MHz) Power supply (5 V) Sync. signal input Sync. signal output Power supply (5 V) System clock input (30 MHz) System clock output (30 MHz) System master clock select (0: 60 MHz, 1: 30 MHz) Ground Serial I/O master clock input (128 x Fs) Serial I/O Sync. signal output Initial clear Test mode setting (0: Test, 1: Normal) Data bus type select (0: 8 bit, 1: 16 bit) IRQ output Trigger signal input/output Power supply (5 V) Ground chip select signal input Write signal input Read signal input
PIN NO.
NAME
FUNCTION
I O I O I O I I I I I I O I/O I I I I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O
Address bus of internal register
Ground Power supply (3.3 V)
Data bus of internal register
Ground Power supply (3.3 V) Power supply (5 V) I/O I/O I/O I/O I/O I/O O I I I I I I I I O O O O O O O O I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O
Data bus of internal register
WAIT output Ground
Serial data input
Ground Power supply (5 V)
Serial data output
Ground
Parallel data bus
Power supply (5 V) Power supply (3.3 V)
Vss 89 DB13 90 DB14 91 DB15 92 DB16 93 DB17 94 DB18 95 DB19 96 DB20 97 DB21 98 DB22 99 Vss 100 Vdd 101 DB23 102 DB24 103 DB25 104 DB26 105 DB27 106 DB28 107 DB29 108 DB30 109 DB31 110 111 TIMO//DBOE Vss 112 Vdd 113 DA00 114 DA01 115 DA02 116 DA03 117 DA04 118 DA05 119 DA06 120 DA07 121 Vss 122 DA08 123 DA09 124 DA10 125 DA11 126 DA12 127 DA13 128 DA14 129 DA15 130 Vss 131 Vdd 132 (n.c) 133 Vdd 134 DA16 135 DA17 136 DA18 137 DA19 138 DA20 139 DA21 140 DA22 141 DA23 142 Vss 143 DA24 144 DA25 145 DA26 146 DA27 147 DA28 148 DA29 149 DA30 150 DA31 151 Vdd 152 Vss 153 A00 154 A01 155 A02 156 A03 157 A04 158 A05 159 A06 160 A07 161 A08 162 A09 163 Vss 164 Vdd 165 A10 166 A11 167 A12 168 A13 169 A14 170 171 A15/RAS 172 A16/CAS 173 A17/CE /WE 174 /OE 175 Vdd 176
Parallel data bus
Ground Power supply (3.3 V)
Parallel data bus
Timing signal output/ Parallel data bus output/ input Ground Power supply (5 V)
Memory data bus
Ground
Memory data bus
Ground Power supply (3.3 V) Not used Power supply (5 V) I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O O O O O O O O O O O O O O O O O O O O O
Memory data bus
Ground
Memory data bus
Power supply (5 V) Ground
Memory address (SRAM, PSRAM, DRAM)
Ground Power supply (3.3 V) Memory address (SRAM, PSRAM, DRAM) Memory address (SRAM, PSRAM) Memory address (SRAM, PSRAM), /RAS (DRAM) Memory address (SRAM, PSRAM), /CAS (DRAM) Memory address (SRAM), /CE (PSRAM) Memory write enable signal Memory output enable signal Power supply (5 V)
46
AW4416
CI-DRC (XY629A00) Gate Array
PIN NO.
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80
MAIN: IC830
NAME
GND GND GND NC NC NC DD0 DD1 DD2 DD3 DD4 DD5 DD6 DD7 GND DD8 DD9 DD10 DD11 VDD DD12 DD13 DD14 DD15 GND DWE DRAS DCAS DQM SDRCS0 SDRCS1 VDD GND SDRCLK NC NC VDD GND GND GND VDD VDD VDD XD0 XD1 XD2 XD3 XD4 XD5 XD6 XD7 XD8 XD9 GND XD10 XD11 VDD XD12 XD13 XD14 XD15 XDWRN XDRDN XDACKN XDREQN GND CK512FS GND FS SO0 SO1 SO2 SO3 SO4 SO5 SO6 VDD VDD VDD VDD
I/O
FUNCTION
Ground Not used
PIN NO.
81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 128 129 130 131 132 133 134 135 136 137 138 139 140 141 142 143 144 145 146 147 148 149 150 151 152 153 154 155 156 157 158 159 160
NAME
GND GND GND SI0 SI1 SI2 SI3 GND NC DA13 DA12 DA11 DA10 DA9 DA8 DA7 DA6 GND DA5 DA4 DA3 DA2 DA1 DA0 VDD NC TEST SCANENB TESTMOD0 TESTMOD1 VDD GND CA1 CA2 CA3 CA4 CA5 GND GND GND VDD VDD VDD GND CD0 CD1 CD2 CD3 GND CD4 CD5 VDD CD6 CD7 GND CD8 CD9 CD10 CD11 GND VDD CD12 CD13 CD14 CD15 GND CCSN CRDN CWRN CINTN BACKN BREQN IDEGEN VDD GND RESETN GND VDD VDD VDD
I/O
FUNCTION
Ground
I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O O O O O O O O
I I I I O O O O O O O O O O O O O O I I I I I I I I I
Serial data input Ground Not used
DRAM data bus
Ground DRAM data bus Power supply +3.3V DRAM data bus Ground DRAM write DRAM row address strobe DRAM column address strobe DATA MASK DRAM chip select Power supply +3.3V Ground DRAM clock Not used Power supply +3.3V Ground Power supply +5V
DRAM address bus
Ground
DRAM address bus
Power supply +3.3V Not used Test pin Power supply +3.3V
Ground
CPU address bus
Ground Power supply +5V Ground CPU data bus Ground CPU data bus Power supply +5V CPU data bus Ground CPU data bus Ground Power supply +5V CPU data bus Ground CPU chip select CPU read CPU write CPU interrupt request Bus acknowledge Bus request Gate enable Power supply +5V Ground Reset Ground Power supply +3.3V
I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O O O O I I I O O O O O O O
SCSI data bus
I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O I I I O I O O I
Ground SCSI data bus Power supply +5V SCSI data bus Write Read DMA acknowledge DMA request Ground Clock Ground Clock
Serial data output
Power supply +5V Power supply +3.3V
47
AW4416
LR38791 (XY631A00) Gate Array
PIN NO.
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64
SUB-CPU: IC305
NAME
FB17 GND GND VDD VDD SD0 SD1 SD2 SD3 SD4 SD5 SD6 SD7 GND SD8 SD9 SD10 SD11 SD12 SD13 SD14 SD15 VDD SA0 SA1 SA2 XSRD XSWR XCS1 XCS2 XCS3 XRST XFDRST VDD VDD GND GND CKI KD0 KD1 KD2 KD3 KD4 KD5 KD6 KD7 TESTSHM KD8 KD9 KD10 KD11 KD12 KD13 KD14 KD15 GND LED0 LED1 LED2 LED3 LED4 LED5 LED6 LED7
I/O
O
FUNCTION
Fader control Ground Power supply
PIN NO.
65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 128
NAME
LED8 GND GND VDD VDD LED9 LED10 LED11 LED12 LED13 LED14 LED15 TESTO_DC GND RA1 RB1 RA2 RB2 RA3 RB3 RA4 RB4 RA5 RB5 GND FA1 FB1 FA2 FB2 FA3 FB3 FA4 FB4 VDD VDD GND GND FA5 FB5 FA6 FB6 FA7 FB7 FA8 FB8 VDD FA9 FB9 FA10 FB10 FA11 FB11 FA12 FB12 GND FA13 FB13 FA14 FB14 FA15 FB15 FA16 FB16 FA17
I/O
O
FUNCTION
LED control Ground Power supply
I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O I I I I I I I I I I
System data bus
O O O O O O O O I I I I I I I I I I O O O O O O O O
LED control
Ground
Test pin Ground
System data bus
Encoder Input
Power supply System address bus Read Write
Ground
Chip select Reset Fader reset Power supply Ground System clock input
Fader control
Power supply Ground
I I I I I I I I I I I I I I I I I I O O O O O O O O
KEY control
O O O O O O O O O O O O O O O O O O O O O O O O O
Fader control
Power supply
Test pin
Fader control
KEY control
Ground
Ground
LED control
Fader control
48
AW4416
LR38792 (XY630A00) Gate Array
PIN NO.
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64
MAIN: IC710
NAME
SA4 GND GND VDD VDD SD0 SD1 SD2 SD3 SD4 SD5 SD6 SD7 GND SD8 SD9 SD10 SD11 SD12 SD13 SD14 SD15 VDD MTCOUT MTCIN FLSD FLXCS FLSCK GND PA0 PA1 PA2 PA3 VDD VDD GND GND PA4 PA5 PA6 PA7 PB0 PB1 PB2 PB3 PB4 PB5 PB6 PB7 GND PX0 PX1 PX2 PX3 PY0 PY1 PY2 PY3 PY4 PY5 PY6 PY7 FS512 FS256
I/O
I
FUNCTION
System address bus signal Ground Power supply
PIN NO.
65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 128
NAME
FS128 GND GND VDD VDD XFS64 FS64 XSYNC ALRCK WCDIR WCMY1 WCMY2 WCBNC VDD MCK0 XTL45I XTL49I GND VC045I PDOUT45 VDD VC049I PDOUT49 GND SCANEN TESTMODE TEST0_DC XSCS30 XSCS31 XSCS32 XSCS33 XSCS34 XSCS35 VDD VDD GND GND XSCS36 XSCS37A XSCS37B XSCS10 XSCS11 XSCS12 XSCS13 XSCS14 XSCS15 XSCS16 XSCS17 XTCL XRST XCS1 XCS3 XSCS XSRD XSWR VDD SA18 SA19 SA20 SA21 SA0 SA1 SA2 SA3
I/O
O
FUNCTION
Clock Ground Power supply
I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O O I O O O I/O I/O I/O I/O
System data bus
O O O O I I I I O I I I O I O I I O O O O O O O
Clock
Ground
Power supply Clock
Crystal oscilator Ground
System data bus
VCO Power supply
Power supply MTC out MTC in FL data FL chip select FL clock Ground Port A Power supply Ground
VCO Ground
Test pin
Chip select
Power supply Ground
I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O O O O O I/O I/O I/O I/O I/O I/O I/O I/O O O
Port A
Port B
Ground Port X
O O O O O O O O O O O I I I I I I I I I I I I I I I
Chip select
Test pin Reset
Chip select Read Write Power supply
Port Y
Clock
System address bus signal
49
AW4416
SPC7214F0B (XY625A00) SCSI Control
PIN NO.
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50
MAIN: IC820
NAME
LVDD EXCLK Vss OSCIN OSCOUT LVDD CLKSEL0 CLKSEL1 VC XPLLPD PLLCT0 PLLCT1 TESTMON TESTEN DB0 DB1 DB2 DB3 HVDD DB4 DB5 DB6 DB7 AD0 Vss LVDD AD1 AD2 AD3 AD4 XWR XRD XRESET XINT XCS Vss XPDACK XPRD XPWR PDREQ PD15 PD0 PD14 PD1 HVDD PD13 PD2 PD12 PD3 Vss
I/O
I I O I I O I I I O I I/O I/O I/O I/O I/O I/O I/O I/O I
FUNCTION
Power supply +3.3V External clock input Ground Oscillator input Oscillator output Power supply +3.3V Input clock select System clock select Internal VCO control PLL power down input PLL control Test monitor output Test input Data bus Power supply +5V Data bus Address bus Ground Power supply +3.3V
PIN NO.
51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100
NAME
LVDD PD11 PD4 PD10 PD5 PD9 PD6 PD8 PD7 Vss XSIO HVDD XSREQ Vss XSCD XSSEL Vss XSMSG XSRST Vss XSACK HVDD XSBSY NC Vss HVDD XSATN Vss XSDBP HVDD XSDB7 Vss NC XSDB6 HVDD XSDB5 Vss XSDB4 HVDD XSDB3 Vss XSDB2 NC HVDD XSDB1 Vss XSDB0 HVDD NC Vss
I/O
I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O
FUNCTION
Power supply +3.3V
Port DMA data bus
I I I I I I I O I I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O
I/O I/O I/O
Address bus Data write (Low active) Data read (Low active) System reset (Low active) Interrupt request (Low active) Chip select (Low active) Ground Port DMA acknowledge Port read (Low active) Port wright (Low active) Port DMA request (Low active)
I/O I/O I/O I/O I/O
Port DMA data bus Power supply +5v Port DMA data bus Ground
I/O I/O
Ground SCSI I/O signal (Low active) Power supply +5V SCSI REQ signal (Low active) Ground SCSI C/D signal (Low active) SCSI SEL signal (Low active) Ground SCSI MSG signal (Low active) SCSI RST signal (Low active) Ground SCSI ACK signal (Low active) Power supply +5V SCSI BSY signal (Low active) Not used Ground Power supply +5V SCSI ATN signal (Low active) Ground SCSI data parity (Low active) Power supply +5V SCSI data bus (Low active) Ground Not used SCSI data bus (Low active) Power supply +5V SCSI data bus (Low active) Ground SCSI data bus (Low active) Power supply +5V SCSI data bus (Low active) Ground SCSI data bus (Low active) Not used Power supply +5V SCSI data bus (Low active) Ground SCSI data bus (Low active) Power supply +5V Not used Ground
50
AW4416
AK4528VF (XY624A00) ADC/DAC
PIN NO.
1 2 3 4 5 6 7 8 9 10 11 12 13 14
MAIN: IC201, 204, 207, 210
NAME
VCOM AINR+ AINRAINL+ AINLVREF AGND VA P/S MCLK LRCK BICK SDTO SDTI
I/O
O I I I I I
FUNCTION
Common voltage output Rch positive analog input Rch negative analog input Lch positive analog input Lch negative analog input Volatge reference Analog ground Analog power supply Parallel/serial mode select Master clock Input/Output channel clock Audio serial data clock Audio serial data output Audio serial data input
PIN NO.
15 16 17 18 19 20 21 22 23 24 25 26 27 28
NAME
CKS0 CKS1 DIF DFS PDN DEM0 DEM1 VT VD DGND AOUTLAOUTL+ AOUTRAOUTR+
I/O
I I I I I I I
FUNCTION
Master clock select Digital audio interface select Double speed sampling mode Power-down mode De-emphasis control Outpt buffer power supply Digital power supply Digital ground Lch negative analog output Lch positive analog output Rch negative analog output Rch positive analog output
I I I I O I
O O O O
MBCG46183-129 (XV833A00) Gate Array
PIN NO.
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24
MAIN: IC707
NAME
D5 D6 D7 /IRQ0 /IRQ1 Vss /IRQ2 /IRQ3 /RD /WR /CE /ASTB TESTSIO RX0 TX0 RX1 TX1 Vss VDD RX2 TX2/BO2 RX30 TX30 RX31
I/O
I/O I/O I/O I/O I/O I/O I/O I I I I I I O I O
FUNCTION
Data Bus Interrupt Request Port 0 Interrupt Request Port 1 Ground Interrupt Request Port 2 Interrupt Request Port 3 Read Signal Input Wright Signal Input Chip Enable Input Address Strobe (Not used: to ground) Input with Pull-down Resistor (50k) Receive Data 0 Transmit Data 0 Receive Data 1 Transmit Data 1 Ground Power Supply Receive Data 2 Transmit Data 2 Receive Data 30 Transmit Data 30 Receive Data 31
PIN NO.
25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48
NAME
TX31 RX32 TX32 RX33 TX33 /IC Vss XI Vss XO A0 A1 A2 A3 A4 A5 CPUCLK Vss VDD D0 D1 D2 D3 D4
I/O
O I O I I/O I I I/O I I I I I I I
FUNCTION
Transmit Data 31 Receive Data 32 Transmit Data 32 Receive Data 33 Transmit Data 33 Initial Clear Ground Quartz Crystal Input Ground Quartz Crystal Output
Address Bus
I O I O I
I/O I/O I/O I/O I/O
CPU Clock Ground Power Supply
Data Bus
DS12887 (XV618A00) Real Time Clock
PIN NO. 1 2 3 4 5 6 7 8 9 10 11 12 NAME MOT N.C N.C AD0 AD1 AD2 AD3 AD4 AD5 AD6 AD7 GND I/O I I/O I/O I/O I/O I/O I/O I/O I/O FUNCTION Bus type selection PIN NAME NO. 13 /CS 14 AS 15 R//W 16 N.C 17 DS 18 /RESET 19 /IRQ 20 N.C 21 N.C 22 N.C 23 SQW 24 Vcc I/O I I I I I O FUNCTION Chip select Address strobe Read / Write Data strobe Reset Interrupt request
MAIN: IC709
Multiplexed address / Data bus
O
Ground
Square wave Power supply +5 V
51
AW4416
SED1335F0B (XQ595A00) LCDC (LCD Controller)
PIN NO. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 NAME VA5 VA4 VA3 VA2 VA1 VA0 /VWR /VCE /VRD /RES NC NC /RD /WR SEL2 SEL1 XG XD /CS A0 VDD D0 D1 D2 D3 D4 D5 D6 D7 XD3 I/O O O O O O O O O I I I I I I O I I I/O I/O I/O I/O I/O I/O I/O I/O O FUNCTION PIN NO. 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 NAME XD2 XD1 XD0 XECL XSCL Vss LP WF YDIS YD YSCL VD7 VD6 VD5 VD4 VD3 VD2 VD1 VD0 VA15 VA14 VA13 VA12 VA11 VA10 VA9 VA8 VA7 VA6 NC I/O O O O O O O O O O O I/O I/O I/O I/O I/O I/O I/O I/O O O O O O O O O O O FUNCTION Data bus output for 4 bit dot
MAIN: IC602
VRAM address bus
VRAM read/write Memory control Not used Initial clear Not used Not used Read strobe Write strobe Bus select Bus select Clock Clock Chip select Data mode select Power supply
S driver enable, chain clock Data bus shift clock Ground X driver latch pulse Frame signal for X/Y driver Power down signal for displaying off mode Scan start signal Scan shift clock
VRAM data bus
VRAM address bus
Data bus
Data bus output for 4 bit dot
Not used
YM3436DK (XG948E00) DIR2 (Digital Format Interface Receiver)
PIN NO. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 NAME DAUX HDLT DOUT VFL OPT SYNC MCC WC MCB MCA SKSY XI XO P256 I/O I O O O O O O O O O I I O O O O I I I I I FUNCTION Auxiliary input for audio data Asynchronous buffer operation flag Audio data output Parity flag output Fs x 1 Synchronous output signal for DAC Fs x 1 Synchronous output signal for DSP Fs x 64 Bit clock output Fs x 1 Word clock output Fs x 128 Bit clock output Fs x 256 Bit clock output Clock synchronization control input Crystal oscillator connection or external clock input Crystal oscillator connection VCO oscillating clock connection PLL lock flag Logic section power (GND) PLL time constant switching output Data input mode selection Data input mode selection Data output mode selection Data output mode selection Clock mode switching input 1 PIN NO. 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 NAME RSTN VDDA CTLN PCO (NC) CTLP VssA TSTN KM2 KM0 FS1 FS0 CSM EXTW DDIN LR VDD ERR EMP CDO CCK CLD I/O I I O I I I I O O I I I O O O O I I FUNCTION System reset input VCO section power (+5 V) VCO control input N PLL phase comparison output
MAIN: IC507
15 LOCKN 16 Vss 17 TST2 18 DIM1 19 DIM0 20 21 22 DOM1 DOM0 KM1
VCO control input P VCO section power (GND) Test terminal. Open for normal use Clock mode switching input 2 Clock mode switching input 0 Channel status sampling frequency display output 1 Channel status sampling frequency display output 0 Channel status output method selection External synchronous auxiliary input word clock EIAJ (AES/EBU) data input PLL word clock output Logic section power (+5 V) Data error flag output Channel status emphasis control code output 3-wire type microcomputer interface data output 3-wire type microcomputer interface clock input 3-wire type microcomputer interface load input
52
AW4416
YM3437C-F (XM530A00) DIT2 (Digital Format Interface Transmitter)
PIN NO. 1 2 3 4 NAME Vss MCLK DM0 DM1 I/O I I I PIN NAME I/O NO. 9 MUTE Ground I 10 VFL Master clock input I 11 CCK/CCB I DIN/BCLK/WCLK format select DM1,DM0=0,0 DSP,LDSP (64 bit,LSB first) 12 CIN/UDB I DM1,DM0=0,1stereo,DSP (64 bit,MSB first) DM1,DM0=1,0 DSP2 (128 bit,MSB first) DM1,DM0=1,1 BB (64 bit,MSB first) 13 CLD/AUXTN I System reset 14 CNTR/BLKIN I Word clock input 15 Digital audio serial data input CSM I FUNCTION Power supply (+5 V) 16 DOUT O FUNCTION
MAIN: IC508
Mute Validity flag C,U bit clock input/C bit data input C,U bit data input/U bit data input
5 6 7 8
RSTN WCIN DIN VDD
I I I
End of C,U bit input/16,20 bit/24 bit select 32 bit counter reset/Top of block Channel status input mode select CSM=0 Asynchronous mode, CSM=1 Synchronous mode Digital interface formatted data output
53
AW4416
IC BLOCK DIAGRAM
TC74HC02AF (XD600A00) Quad 2 Input NOR
MIAN: IC515
TC74VHC04F EL (XM332A00) 74VHC04SJX (XY871A00) HD74LS06FPEL (XH610A00) Hex Inverter
MIAN: IC613 SUB-FADER: IC120-122
TC74VHC08F (XT014A00) 74VHC08SJX (XY872A00) Quad 2 Input AND
MIAN: IC825
1A 1B 1Y
1 2 3 14 13 12
1Y 1A 1B 2Y 2A 2B Vss
1 2 3
14 13 12
VDD 4Y 4A
VDD 4B 4A 4Y 3B 3A 3Y
1A
4 5 6 7 11 10 9 8
1 2 3 4 5 6 7
14 13 12 11 10 9 8
VDD 2A 6A 2B 6Y 2Y 5A 5Y 4A 4Y VSS
7 8 6 9 5 10 4 11
4B 1Y 3Y 2A 3A 3B 2Y 3A 3Y Vss
TC74VHC11F(EL) (XT812A00) Triple 3 Input AND
MIAN: IC828, 834
TC74VHC14F (XW876A00) HD74HC14FPEL (XL094A00) MM74HC14SJX (XW104A00) Hex Inverter
MIAN: IC827 SUB-CPU: IC203, 310, 311
74VHC32SJX (XY306A00) TC74VHC32FEL (XY537A00) Quad 2 Input OR
MIAN: IC826
1A 1B
1 2 3 14 13 12
1A 1B 2A 2B 2C 2Y VSS
1 2 3
14 13 12
VDD 1C 1Y 3C 3B 3A 3Y
Vcc 4B 4A 4Y 3B 3A 3Y
1A 1Y 2A 2Y 3A 3Y GND
1 2 3 4 5 6 7
14 13 12 11 10 9 8
VDD 6A 6Y 5A 5Y 4A 4Y
1Y 2A 2B 2Y GND
4 5 6 7
11 10 9 8
4 5 6 7
11 10 9 8
TC74VHC74F-EL (XW875A00) 74VHC74SJX (XY875A00) Dual D-Type Flip-Flop
MIAN: IC506, 829, 832, 835
TC74VHC138F (XT015A00) 74VHC138SJX (XY873A00) 3 to 8 Demultiplexer
MIAN: IC807, SUB-CPU: IC302
A Select B C G2A Enable G2B G1 Output Y7 GND
1 A 2 3 4 5 6 7 8 B C Y0 Y1 15 14 13 12 11 10 9 16
TC74VHC157F(EL) (XT475A00) 74VHC157SJX (XY870A00) Quad 2 to 1 Multiplexer
MIAN: IC815, 816, 831
SELECT 1A 1B
1 S 2 3 4 5 6 7 8 1A 1B 1Y 2A 2B 2Y 3Y G 4A 4B 4Y 3A 3B 16 15 14 13 12 11 10 9
1CLR 1D 1CK 1PR 1Q 1Q GND
1 CLR 2 3 4 5 6 7 D
14 13 CLR D 12 11 10 9 8
VCC 2CLR 2D 2CK 2PR 2Q 2Q
Vcc YO Y1 Y2 Output Y3 Y4 Y5 Y6
Vcc STROBE 4A 4B 4Y 3A 3B 3Y
CK PR Q Q
CK PR Q Q
G2A Y2 G2B Y3 G1 Y7 Y4 Y5 Y6
1Y 2A 2B 2Y GND
PR L H L H H H
INPUTS CLR CLK H L L H H H X X X f f L
D X X X H L X
OUTPUTS Q Q H L H H L QO L H H L H QO
54
AW4416
HD74HC174FP (XV610A00) TC74HC174F(EL) (XY878A00) Hex D-Type Flip-Flop
SUB-CPU: IC306-308
CLEAR 1Q 1D 2D 2Q 3D 3Q GND
1 2 16 15
TC74VHC245F (XT487A00) 74VHC245ASJX (XY874A00) TC74HC245AF (XS720A00) MM74HC245ASJX (XW107A00) Octal 3-State Bus Transceiver
MAIN: IC302-304, 504, 606-612, 702, 714, 811, 821, 814, 817, 818, 819 SUB-CPU: IC304
D1R A1 A2 A3 A4 A5 A6 A7 A8 GND
1 2 20 19 18
SN75121NSR (XU816A00) Dual Line Driver
MAIN: IC704
Vcc 6Q 6D 5D 5Q 4D 4Q CK
1A 1B 1C 1D 1E 1F 1Y GND
1 2 3 4 5 6 7 8
16 15 14 13 12 11 10 9
Vcc 2F 2E 2D 2C 2B 2A 2Y
Q G G DCK
Q C KD
3 4 5
14 13 12
DCK G Q
C KD G Q
Vcc G B1 B2 B3 B4 B5 B6 B7 B8
3 4 5 6 7 8 9 10
6 7 8
DCK G Q
C KD G Q
11 10 9
17 16 15 14 13 12 11
SN75124NS (XN976A00) SN75124NSR (XV930A00) Triple Line Receiver
MAIN: IC703
1A 1B 2R 2S 2A 2B 2Y GND
1 2 16 15
TC74HC4052AF (XS790A00) MM74HC4052SJX (XY876A00) Differential 4-Channel Multiplexer/Demultiplexer
SUB-FADER: IC106, 111
MM74HC4053SJX (XY877A00) TC74HC4053AF(EL) (XY879A00) Triple -Channel Multiplexer/Demultiplexer
MAIN: IC701
Vcc 1S 1R 1Y 3A 3S 3R 3Y 0Y 2Y Y-COM 3Y 1Y INH VEE VSS
1 16
3 4 5
14 13 12
VDD 2X 1X X-COM 0X 3X A B
Switches IN/OUT
Y1 1 2 3 4 5 6 7 8 Y1 Y0 Z1 Z Z0 INH VEE VSS VDD 16 Y X X1 X0 A B C 15 14 13 12 11 10 9
+DC Voltage Supply Commons OUT/IN Y - do. Swiches IN/OUT - do Control Input - do. - do. A B C X X1 X0
0Y
2 3 4 5 6 7
2Y
2X
15 14 13 12 11 10 9
- do. - do. -
Y0 Z1
Z
Y-COM 1X 3Y X-COM 1Y INH
B
6 7 8
11 10 9
Commons OUT/IN Swiches IN/OUT
Z0
0X 3X A
Control Inhibit -DC Voltage Supply - do -
8
TC7WU04F (XN567A00) Triple lnverter
MAIN: IC516, 712, 713, 833
TC7S04F (XJ018A00) Inverter Gate
MAIN: IC511
TC7S08F (XM616A00) 2 Input AND Gate
MAIN: IC510, 614
1A 3Y 2A GND
1
8
Vcc 1Y 3A 2Y
NC IN VSS
1 2
5
VDD
IN B IN A
1 2 3
5
VDD
2 3 4
7 6 5
3
4
OUT VSS
4
OUT
55
AW4416
AM26LS31M (XN919A00) AM26LS31CNSR (XU996A00) Quad Line Driver
MAIN: IC513
1A 1Y 1Z ENABLE G 2Z 2Y 2A GND
1 2 3 4 5 6 7 8 16 15 14 13 12 11 10 9
DS26C32ATMX (XU815A00) Quad Differential Line Receiver
MAIN: IC512, 706
NJM2068MD-T1 (XJ553A00) µPC4570G2 (XF291A00) NJM4556AMT1 (XQ138A00) Dual Operational Amplifier
MAIN: IC101-113, 116-199, 202, 203, 205, 206, 208, 209, 211-215
Vcc 4A 4Y 4Z ENABLE G 3Z 3Y 3A
INPUT A INPUT A OUTPUT A ENABLE OUTPUT C INPUT C INPUT C GND
1 2 3 4 5 6 7 8
REG
16 15 14 13 12 11 10 9
Vcc INPUT B INPUT B OUTPUT B ENABLE
+
+
+ + -
INPUT A H L H L X
ENABLES G G H X H X X L X L L H
OUTPUTS Y Z H L L H H L L H Z Z
H= high level L= low level X= irrelevant Z= high impedance (off)
MC26LS30D (XL334A00) Linr Driver
MAIN: IC705
SINGLE-ENDED MODE EIA-423 16 Input A 2 15 13 Input B 3 14 12 Input C 6 11 9 Input D 7 10 SR-A Out A SR-B Out B SR-C Out C SR-D Out D
DIFFERENTIAL MODE EIA-422 Enable AB Input A 3 2 15 Out A 14 Out B 11 Out C 10 Out D
Vcc Input A Input B/ Enable AB Mode GND Input C/ Enable CD Input D
1 2 3 4 5 6 7 8
Input D 7 6 Enable CD Vcc VEE
1 Gnd 5 8 Mode 4
VEE
NJM2904M (XV190A00) Dual Operational Amplifier
MAIN: IC514
TA7291F (XW618A00) Motor Driver
SUB-FADER: IC101-105, 107-110, 112-119
Vcc 11 Vref 5 15 Vs GND NC NC 4 OUT1 M 13
Protector circuit (Heat interception)
1 2 3 4 5 6 7 8 16 15 14 13 12 11 10 9
Output A Inverting Input A Non-Inverting Input A Ground
1 2 3 4 -V
+V
8 7 6 5
+DC Voltage Supply Output B Inverting Input B Non-Inverting Input B
-
+ + -
7 IN1
9 IN2
56
+ 16 15 14 13 12 11 10 9
+
OUTPUT D INPUT D
1 2
A
B
3 4 5 6 7
8 9
INPUT D
+V
-IN OUT +IN A A A
-V
-IN +IN OUT B B B
+V
SR-A Operation Output A Output B SR-B SR-C Output C Output D SR-D X 0 X +5.0 -5.0 Differential (EIA-422-A) Vcc +5.0 VEE GND Mode 0 0 0 0 0 0 1 1 1 1 1 X
Inputs A B C D 0 1 X 1 0 1 0 1 0 0 0 0 0 1 0 0 0 0 0 1 0 0 0 0 0 0 0 1 0 0 0 1 0 0 1 1 0 1 X 0 0 0 0 1
Outputs A B C D 0 1 Z 1 0 1 0 1 0 0 0 1 0 Z 0 1 0 0 0 1 0 0 1 0 0 1 0 Z 0 0 0 1 0 0 1 1 0 1 Z 0 0 0 0 1
Single-Ended (EIA-423-A)
X X X X
Z Z Z Z
X = Don't Care Z = High Impedance (Off)
NC Vs NC OUT2 NC Vcc NC IN2
OUT1 Vref NC IN1 NC
OUT2
1 GND
AW4416
MAX202CSE (XP113A00) RS-232C Transceiver
SUB-CPU: IC201
+5V INPUT 0.1uF + 7 Vcc C1+ C1 C2+ C2 +5V 400K 5 T1 IN +5V 400K 4 T2 IN +5V 400K TTL/CMOS INPUTS 14 T3 IN +5V 400K 15 T4 IN +5V 400K 19 T5 IN 18 N.C. GND 6 T5 T5 OUT 16 17 SHDN C1 10 11 C2+ T4 T4 OUT 20 V+ 9 12 T3 T3 OUT 1 RS-232 OUTPUTS GND Vcc C1+ T2 T2 OUT 3 T1 IN 5 6 7 8 16 15 14 13 T5 OUT T4 IN T3 IN V C2 T1 T1 OUT 2 T2 OUT T2 IN 3 4 18 17 N.C. SHDN +5V TO +10V VOLTAGE DOUBLER +10V TO 10V VOLTAGE INVERTER V+ 0.1uF + 6.3V
BH9595FP-Y (XV617A00) SCSI Terminator
MAIN: IC821
8 0.1uF 6.3V 0.1uF 16V + 10 11 + 12
9
Not to be used (N.C.) 1 2 "H" : ENABLE "L" : DISCONNECT EN SCSI LINE 15 T5 IN
1 2
TSD MODE CONTROL to SW POW POW
25 24 POW 23 22 21
TSD VM
V
13 0.1uF + 16V
T3 OUT T1 OUT
20 19
T4 OUT
3 4 5
SCSI LINE 14 SCSI LINE 13 SCSI LINE 12
SCSI LINE 16 SCSI LINE 17
SCSI LINE 18
6 POW (PUSH-PULL) POW (PUSH-PULL)
20
SCSI LINE 11
GND GND 7 8 9 POW (PUSH-PULL) POW (PUSH-PULL)
GND SCSI LINE 1 SCSI LINE 2
110 Resistors 19 18 SCSI LINE 10 SCSI LINE 9
SCSI LINE 3
10 11 12 POW POW (PUSH-PULL)
17 16 2.85V SUPPLY 15
SCSI LINE 8 SCSI LINE 7 SCSI LINE 6
SCSI LINE 4 SCSI LINE 5
(PUSH-PULL)
VDD1
13
2.85V GENERATER BH9595FP-Y
14
VDD1
57
AW4416
TEST PROGRAM
1. Getting Ready 1-1 Rear Panel (1) Insert slot check cards into option I/O slots 1 and 2. (2) Install the hard-disk drive unit for the test into the 2.5" hard drive slot. (3) Connect a mouse to the mouse connector (9-pin DSUB connector). (4) Connect an external SCSI hard drive to the SCSI connector (50-pin half-pitch connector). * The external disk capacity must be at least 4GB, and the disk must already be physically formatted. * The SCSI cable length should not exceed 300mm. * Be sure that the external drive is terminated. (Plug a terminator into the drive's free SCSI connector.) * Set the external drive's SCSI address to 0. (5) Using a dedicated cable, connect the 8-pin MiniDIN connector on the slot-check card in option slot 1 to the TO HOST connector (8-pin MiniDIN connector) on the AW4416. (6) Using a BNC cable, connect the WORDCLOCK IN terminal to the WORD CLOCK OUT terminal. (7) Using a pin-jack cable, connect the DIGITAL IN connector to the DIGITAL OUT connector. (8) Using a MIDI cable, connect the MIDI IN connector to the MIDI OUT connector. (9) Connect a footswitch to the FOOT SW jack. 1-2 Rear Panel (1) Insert the specified disc into a CD-RW drive, and install this drive in the AW4416. (Set the CD-RW drive's SCSI ID to 3.) 2. Diagnostics Program 2-1 Program Modes The installed diagnostics program runs in four different diagnostic modes, as follows.
Mode AW4416 (full assembly) diagnostics MAIN-sheet diagnostics Startup Keys
UTILTY HOME
Purpose To be run after full assembly is completed.
UTILTY
1-16
Tests the MAIN sheet only.
PN-sheet diagnostics
UTILTY
17-24 RTN
Tests the PN sheet only.
SUB-sheet diagnostics
UTILTY
MONI
Tests the SUB sheet only.
Note: Key locations are shown in the following illustration. 2-2 Locations of Program Startup and Selection Keys
70
AW4416
3. Program Startup and Test Menu Display Start the program in the desired mode by pressing the corresponding keys, as indicated below. The program starts up, and the screen displays the test menu. The appearance of the menu screen differs somewhat according to the mode. 3-1 AW4416 (Full Assembly) Diagnostics Mode (1) Startup 1) Hold down the UTILTY and HOME keys, and turn the power on. 2) When the following title screen appears on the display, release the keys.
3) The program starts up in AW4416 (full assembly) diagnostics mode, and the test menu appears on the LCD. (2) Test Menu Display
Blinking Cursor
Test not available.
3-2 MAIN-Sheet Diagnostics Mode 1) Hold down the UTILTY key and the 1-16 key, and turn the power on. 2) When the following title screen appears on the display, release the keys.
3) The program starts up in MAIN-sheet diagnostics mode, and the test menu appears on the LCD.
71
AW4416
(2) Test Menu Display
Blinking Cursor
Test not available.
3-3 PN-Sheet Diagnostics Mode (1) Startup 1) Hold down the UTILTY key and the 17-24 key, and turn the power on. RTN 2) When the following title screen appears on the display, release the keys.
3) The program starts up in PN-sheet diagnostics mode, and the test menu appears on the LCD. (2) Test Menu Display
Blinking Cursor
Test not available.
3-4 SUB-Sheet Diagnostics Mode (1) Startup 1) Hold down the UTILTY and MONI keys, and turn the power on.
72
AW4416
2) When the following title screen appears on the display, release the keys.
3) The program starts up in SUB-sheet diagnostics mode, and the test menu appears on the LCD. (2) Test Menu Display
Blinking Cursor
Test not available.
4. Test Menu 4-1 Tests Available in Each Mode
Program Mode Test Test
Program Mode
Note 1:T = AW4416 (full assembly) diagnostics mode M = MAIN-sheet diagnostics mode P = PN-sheet diagnostics mode S = SUB-sheet diagnostics mode Note 2: O = Available, X = Not available Note 3: The SWITCH and LED tests are mode-dependent: the test content differs according to the mode. All other tests are the same regardless of the mode they are executed in.
73
AW4416
4-2 Selecting and Executing a Test (1) Use the or key to move the cursor to the test you wish to run.
(2) Press ENTER to run the test. 4-3 Test Result (1) The test result is indicated to the left of the test item in the menu (see section 4-5, "Test Result Display", below). If the . If test ended abnormally or was exited before completion, the screen test ended normally, the screen displays displays NG. 4-4 Canceling a Test (1) You can cancel a test that is currently running test by pressing the CANCEL key. 4-5 Test Result Display
Result Indication Ended normally Ended abnormally Canceled
5. Tests With the exception of the SWITCH and LED tests, all tests are the same regardless of the test mode. 5-1 Test Runtime Screens Test runtime screens differ according to the test. There are four basic screen types, A to D, as shown below.
(1) Test Screen Type A Test name Indication Prompts Indication Test name Indication Prompts Indication
(2) Test Screen Type B
Results Indication Prompts & status Indication
Exit method Indication
Exit method Indication
74
AW4416
(3) Test Screen Type C Test name Indication Result Indication NG message area Indication
Exit method Indication
1) If result is OK
Test name Indication Test results Indication Overall result Indication
(4) Test Screen Type D
Exit method Indication
2) If result is NG
NG message areas Indication
5-2 Test Descriptions 5-2-1 Switch Input Test (01 SWITCH) (1) Display (Test Screen Type A) 1) Test name SWITCH (2) Test Content 1) This test checks the input from the control panel switches and the footswitch. 2) The test content varies according to the program mode, as follows.
75
AW4416
q If AW4416 mode Tests all control panel switches and the footswitch. w If PN-sheet mode Tests all control panel switches. e If SUB-sheet mode Tests the following 16 control panel switches: SONG, VIEW, AUX5, SHIFT-L, BANK, SEL1, SEL9, ON1, ON9, ABS, CUE, SAFE, JOG ON, NUM, REPEAT, REW. 3) The screen's prompt area displays a layout of the switches to be tested, while the status area displays the name of the switch to be tested. Carry out the test in accordance with the screen prompts. 4) When a switch is tested and found to be normal, the switch indication disappears from the layout and the switch indication for the next switch to be tested begins blinking. (3) Judgment 1) Exit-method area EXIT: [SOLO] + [CANCEL] 2) If input from all switches is normal: When the final switch indication disappears from the displayed layout, the test terminates. The program returns to the test menu screen, and an appears in the left column. (See section 4-5, "Test Result Display.") The cursor automatically advances to the next test in the menu. 3) If the result is NG or if you wish to stop the test before completion: Hold down the SOLO key and press the CANCEL key. The program returns to the test menu screen, and an NG appears in the left column. The cursor does not advance. 5-2-2 LED Test (02 LED) (1) Display (Test Screen Type A) 1) Test name LED (2) Test Content 1) This test checks that control-panel switch LEDs light up correctly. 2) The test content varies according to the program mode, as follows. q If AW4416 mode or PN-sheet mode Tests all control panel LEDs. (See section 6, "Miscellaneous.") w If SUB-sheet mode Tests the following 24 control panel LEDs: SONG, AUX4, SAMPLING PAD 1, SAMPLING PAD 5, SEL1, SEL9, ON1, ON5, ON9, ON13, REC1, REC5, REC9, JOG ON, SOLO, REPEAT, AUX5, AUX6, EFF1, EFF2, HOME (2 LEDs), 1-16 (2 LEDs). e This is a visual check. Watch that the LEDs light up in order. (3) Judgment 1) Exit-method area OK: [ENTER], NG: [CANCEL] 2) If all tested LEDs light up normally: If all the LEDs targeted by the selected test mode have lit up normally, exit the test by pressing ENTER . The program returns to the test menu screen, and an appears in the left column. The cursor automatically advances to the next test in the menu. 3) If the result is NG or if you wish to stop the test before completion: Press the CANCEL key. The program returns to the test menu screen, and an NG appears in the left column. The cursor does not advance. 5-2-3 LCD Test (03 LCD) (1) Display (Test Screen Type A) 1) The test-name area is blank.
76
AW4416
(2) Test Content 1) This test checks the LCD dots. 2) This is a visual test. Check that all dots blink continuously. (3) Judgment 1) Exit-method area blank 2) If all dots blink correctly (based on visual check): Press ENTER to return to the test menu screen. An appears in the left column, and the cursor advances to
the next test in the menu. 3) If the result is NG or if you wish to stop the test before completion: Press CANCEL . The program returns to the test menu screen, and an NG appears in the left column. The cursor does not advance. 5-2-4 FL Segment Test (04 FL) (1) Display (Test Screen Type A) 1) Test name FL (2) Test Content 1) This test checks that the FL segments light up correctly. 2) This is a visual test. Segments first blink in order, and then all the segments come on solid. Confirm that all of the segments light up. (3) Judgment 1) Exit-method area OK: [ENTER], NG: [CANCEL] 2) If visual check shows that operation is normal: Press ENTER to return to the test menu screen. An appears in the left column, and the cursor advances to
the next test in the menu. 3) If the result is NG or if you wish to stop the test before completion: Press CANCEL . The program returns to the test menu screen, and an NG appears in the left column. The cursor does not advance. 5-2-5 MAIN CPU REC CPU Communication Test (05 DPRAM) (1) Display (Test Screen Type D) 1) Test name DIAGNOSTIC for DPRAM (MIX <-> HDR) (2) Test Content 1) Runs a DP-RAM R/W test to check communication between the MAIN CPU and the REC CPU. 2) Tests the MAIN CPU bus, REC CPU bus, and interrupts. (3) Judgment 1) Results area Checking R/W ...** Checking MIX CPU <-> HDR CPU ...** Exit-method area EXIT: [ENTER / CANCEL] 2) If the results area shows that all test results are OK: Press ENTER to return to the test menu screen. An appears in the left column, and the cursor advances to
the next test in the menu. 3) If a check returns an NG: Checking R/W ... NG NG message NG message MSB LSB 0XXX XXXX a) Write and Read values did not match. A "0" indicates that the bit matched; an "X" indicates a mismatch. b) If all bits are "X", there is a problem with the CS or the Address bus. c) If only one bit is "X", there is a problem with the Data bus.
77
AW4416
Checking MIX CPU <-> HDR CPU ... NG NG message NG message No response from HDR CPU a) Problem with Mixer CPU or HDR CPU interrupts. NG message MSB LSB 0XXX XXXX b) Problem in the CS, Address bus, or Data bus at the Mixer CPU or HDR CPU. To exit, press the CANCEL key. The program returns to the test menu screen, and an NG appears in the left column. The cursor does not advance. 5-2-6 DSP5 Function Test (06 DSP5) (1) Display (Test Screen Type D) 1) Test name DIAGNOSTIC for DSP5 (2) Test Content 1) Checks the MAIN CPU / DSP5 interface. 2) Checks the DSP5 bus connection and serial I/O and parallel I/O connections. (3) Judgment 1) Results area 1: Initialize all DSP5 ... ** 2: CPU Interface IC505 ERR = 0/10000 ... ** IC509 ERR = 0/10000 ... ** 3: SIO Connection [DSP6 -> DSP5] ... ** 4: SIO Connection [DSP5 -> DSP6] ... ** 5: SIO Connection [DSP5 -> DSP5] ... ** 6: PIO Connection [DSP6 <-> DSP5] ... skip! ALL TEST ARE OK! Exit-method area EXIT: [ENTER / CANCEL] 2) If all tests are OK (if the overall result area displays the ALL TESTS ARE OK message): Press ENTER to return to the test menu. An appears in the left column, and the cursor advances to the next test
in the menu. 3) If a check returns an NG: 1: Initialize all DSP5 ... NG NG message TRANS ERROR a) DSP5 initialization problem. 2: CPU Interface NG message IC505 ERR = 0/10000 ... OK IC509 ERR = 10000/10000 ... NG MSB 28 24 20 16 12 8 LSB XXXX XXXX XXXX XXXX XXXX XXXX XXXX XXXX a) Connection problem with IC509 Data bus, Address bus, R/W, or CS. 3: SIO Connection [DSP6 -> DSP5] ... NG NG message NG: IC301 SO[0] -> IC509 SIO[16] a) IC301 SO[0] -> IC509 SIO[16] connection problem. 4: SIO Connection [DSP5 -> DSP6] ... NG NG message NG: IC505 SIO[40] -> IC301 SI[0] a) IC505 SIO[40] -> IC301 SI[0] connection problem. 5: SIO Connection [DSP5 -> DSP5] ... NG NG message NG: IC505 SIO[0] -> IC509 SIO[0] a) IC505 SIO[0] -> IC509 SIO[0] connection problem. 6: PIO Connection [DSP5 -> DSP5] ... skip! not tested. To exit, press CANCEL . The program returns to the test menu screen, and an NG appears in the left column. The cursor does not advance.
78
AW4416
5-2-7 DSP6 Function Test (07 DSP6) (1) Display (Test Screen Type D) 1) Test name DIAGNOSTIC for DSP6 (2) Test Content 1) Checks the MAIN CPU DSP6 interface (DRAM). 2) Checks the DSP5 bus connection and serial I/O and parallel I/O connections. (3) Judgment 1) Results area 1: CPU Interface (Data bus) ... ** 2: CPU Interface (Data bus) ... ** 3: CPU Interface (Chip Select, TXB) ...** 4: CPU Interface (Address bus) ... ** 5: CPU Interface (BUS, W/R, Reg) ... ** 6: DRAM Interface (Data bus) ... ** 7: DRAM Interface (Address bus) ... ** 8: DRAM Interface (Address bus & MPR) ... ** 9: SIO Connection ... ** 10: PIO Connection ... ** ALL TEST ARE OK! Exit-method area EXIT: [ENTER / CANCEL] 2) If all tests are OK (if the overall result area displays the ALL TESTS ARE OK message): Press ENTER to return to the test menu. An appears in the left column, and the cursor advances to the next
test in the menu. 3) If a check returns an NG: 1: CPU Interface (Data bus) ... NG NG message IC301 TXBusy Error 2: CPU Interface (Data bus) ... NG NG message IC301 MSB 28 24 20 16 8 LSB XXXX XXXX XXXX XXXX XXXX XXXX XXXX a) Message shows "0" in bit positions where Write and Read bit values matched. 3: CPU Interface (Chip Select, TXB) ... NG NG message IC301 CS Error 4: CPU Interface (Address bus) ... NG NG message IC301 MSB 28 24 20 16 8 LSB 0000 XXXX XXXX XXXX XXXX XXXX XXXX a) Message shows "0" in bit positions where Write and Read bit values matched. 5: CPU Interface (BUS, W/R, Reg) ... NG NG message IC301 MSB 28 24 20 16 8 LSB X000 XXXX XXXX XXXX XXXX XXXX XXXX a) Message shows "0" in bit positions where Write and Read bit values matched. 6: DRAM Interface (Data bus) ... NG NG message IC306 MSB 28 24 20 16 8 LSB X000 XXXX XXXX XXXX XXXX XXXX XXXX a) Message shows "0" in bit positions where Write and Read bit values matched. 7: DRAM Interface (Address bus) ... NG NG message IC306 MSB 28 24 20 16 8 LSB X000 XXXX XXXX XXXX XXXX XXXX XXXX a) Message shows "0" in bit positions where Write and Read bit values matched. 8: DRAM Interface (Address bus & MPR) ... NG NG message IC301 MSB 28 24 20 16 8 LSB X000 XXXX XXXX XXXX XXXX XXXX XXXX a) Message shows "0" in bit positions where Write and Read bit values matched.
79
AW4416
9: SIO Connection ... NG NG message IC301 SO[4] -> IC306 SIO[4] 10: PIO Connection ... NG NG message NG: IC301 -> IC302 MSB 28 24 20 16 8 LSB 0000 X000 0000 0000 0000 0000 0000 a) Message shows "0" for PIO-bus bits that are OK. To exit, press CANCEL . The program returns to the test menu screen, and an NG appears in the left column. The cursor does not advance. 5-2-8 Encoder Function Test (08 ENCODER) (1) Display (Test Screen Type A) 1) Test name ENCODER (2) Test Content 1) Checks the function of the PAN, EQ-Q, EQ-F, and EQ-G rotary encoders. 2) The prompt area on the display shows encoder images and operating instructions. Carry out the test according to these instructions. (3) Judgment 1) Exit-method area EXIT: [CANCEL] 2) If all encoders have functioned correctly: When the test terminates, the program returns to the test menu screen. An cursor advances to the next test in the menu. 3) If the result is NG or if you wish to stop the test before completion: appears in the left column, and the
Press CANCEL . The program returns to the test menu screen, and an NG appears in the left column. The cursor does not advance. 5-2-9 Jog/Shuttle Function Test (09 JOG/SHUTTLE) (1) Display (Test Screen Type A) 1) Test name JOG/SHUTTLE (2) Test Content 1) Checks jog/shuttle functions (data and cursor functions). 2) The screen's prompt area displays jog/shuttle graphics and operational instructions. Carry out the tests according to the displayed instructions. (3) Judgment 1) Exit-method area EXIT: [CANCEL] 2) If all functions operate correctly: When the test terminates, the program returns to the test menu screen. An cursor advances to the next test in the menu. 3) If the result is NG or if you wish to stop the test before completion: appears in the left column, and the
Press ENTER . The program returns to the test menu screen, and an NG appears in the left column. The cursor does not advance. 5-2-10 Internal HDD Test (10 IDE) (1) Display (Test Screen Type C) 1) Test name IDE (2) Test Content 1) Checks connection and operation of the internal (IDE) hard disk. 2) You should also check that the HDD access LED blinks correctly. (See section 6-(1), "Miscellaneous" for more information.)
80
AW4416
(3) Judgment 1) Exit-method area EXIT: [ENTER / CANCEL] 2) If the disk operates correctly (if the upper right of the screen ... OK): Press ENTER to return to the test menu screen. An appears in the left column, and the cursor advances to
the next test in the menu. 3) If there is a problem, the corresponding NG message will appear. NG message IDE Timeout (Check CPU <-> IDE) a) Error in communication between the CPU and the (IDE) HDD. NG message IDE HDD (Check IDE <-> HDD) a) Error in reading or writing to the HDD. Press CANCEL . The program returns to the test menu screen, and an NG appears in the left column. The cursor does not advance. 5-2-11 External SCSI Device Connection Test (11 SCSI) (1) Display (Test Screen Type C) 1) Test name SCSI (2) Test Content 1) Checks connection and operation of the external SCSI device. (3) Judgment 1) Exit-method area EXIT: [ENTER / CANCEL] 2) If the disk operates correctly (if the upper right of the screen ... OK): Press ENTER to return to the test menu screen. An the next test in the menu. 3) If there is a problem, the NG message appears. NG message NG EXTERNAL SCSI a) Bad connection with external SCSI device. Press CANCEL . The program returns to the test menu screen, and an NG appears in the left column. The cursor does not advance. 5-2-12 Option I/O Slots 1 & 2-Connection Test (12 Slot 1/2) (1) Display (See illustration below) 1) Test name Slot 1/2 (2) Test Content 1) Checks connection of option I/O slots 1 and 2. (3) Judgment 1) Exit-method area --> EXIT: [ENTER / CANCEL] 2) If slots connect and operate correctly:
Test Screen (if OK)
appears in the left column, and the cursor advances to
81
AW4416
Press ENTER to return to the test menu screen. An
appears in the left column, and the cursor advances to the
next test in the menu. 3) If there is a problem, the screen displays the appropriate NG messages.
Test Screen (if NG)
NG message 256FS a) 256FSMY, WCMY [SLOT 1, SLOT 2] connection problem. NG message 128FS a) 128FSMY, WCMY [SLOT 1, SLOT 2] connection problem. NG message 64FS a) 64FSMY, WCMY [SLOT 1, SLOT 2] connection problem. NG message SYNC a) SYNCMY, WCMY [SLOT 1, SLOT 2] connection problem. NG message FS a) FSMY, WCMY [SLOT 1, SLOT 2] connection problem. NG message DATA BUS a) Data bus (YD[0] to YD[15]) connection problem. NG message ADDRESS BUS a) Address bus (YA[1] to YA[10]) connection problem. b) /CSMY[1,2], /RDMY, /WRLMY, /WRHMY connection problem. NG message IRQ a) IRQMY (SLOT 1) connection problem. NG message TX/RX a) TXMY2, RXMY2 (SLOT 2) connection problem. NG message SIGNAL1/2 a) S[1/2]IN-1/2, S[1/2]OUT-1/2 connection problem. NG message SIGNAL3/4 a) S[1/2]IN-3/4, S[1/2]OUT-3/4 connection problem. NG message SIGNAL5/6 a) S[1/2]IN-5/6, S[1/2]OUT-5/6 connection problem. NG message SIGNAL7/8 a) S[1/2]IN-7/8, S[1/2]OUT-7/8 connection problem. To exit, press CANCEL . The program returns to the test menu screen, and an NG appears in the left column. The cursor does not advance.
82
AW4416
5-2-13 TO HOST Function Test (13 TO HOST) (1) Display (Test Screen Type B) 1) Test name TO HOST (2) Test Content 1) Checks the host interface. (3) Judgment 1) Prompt area MAKE TEST LOOP AND PRESS ENTER Exit-method area EXIT: [ENTER / CANCEL] Start the test by pressing ENTER . 2) If result area ...OK Press ENTER to return to the test menu. An appears in the left column, and the cursor advances to the next
test in the menu. 3) If result area ...NG NG message NG message MAIN Tx/Rx a) SIO4 (IC707) TX1, RX1 signal error. NG message CLOCK a) SIO4 (IC707) TX2 signal error. NG message REC Tx/Rx a) REC CPU (IC803) TXD1, RXD1 signal error. To exit, press CANCEL . The program returns to the test menu screen, and an NG appears in the left column. The cursor does not advance. 5-2-14 MIDI Function Test (14 MIDI) (1) Display (Test Screen Type B) 1) Test name MIDI (2) Test Content 1) Checks the MIDI interface and MTC functions. (3) Judgment 1) Prompt area --- MIDI CHECK --MAKE TEST LOOP AND PRESS ENTER Exit-method area EXIT: [ENTER / CANCEL] Start the MIDI test by pressing ENTER . 2) MIDI test result area MTC prompt area ...OK ...NG NG message --- MTC CHECK --MAKE TEST LOOP AND PRESS ENTER At the rear panel, disconnect the MIDI cable from the OUT/THRU connector, and connect it to the MTC connector immediately to the left.
Start the MTC test by pressing ENTER . 3) MTC test result area ...OK ...NG 4) If both tests return OK: Press ENTER to return to the test menu. An test in the menu. 5) If either or both tests return NG: MIDI-test NG message MIDI Tx/Rx a) SIO4 (IC707) TX0, RXO signal error. MIDI-test NG message THRU SELECT appears in the left column, and the cursor advances to the next
83
AW4416
a) MAIN CPU (IC601) Port E8 signal error. To exit, press CANCEL . The program returns to the test menu screen, and an NG appears in the left column. The cursor does not advance. 5-2-15 Mouse Interface Test (15 MOUSE) (1) Display (Test Screen Type A) 1) Test name MOUSE (2) Test Content 1) Tests the mouse interface. (3) Judgment 1) Exit-method area EXIT: [CANCEL] The "prompts & status" area displays graphics and check items. Operate the mouse as indicated (moving the mouse in all four directions and clicking both of the mouse buttons) and confirm that an OK appears to the right of the corresponding items on the display. Check Item Confirm that... MOVE LEFT * Value changes and then OK appears. MOVE UP * Value changes and then OK appears. MOVE RIGHT * Value changes and then OK appears. MOVE DOWN * Value changes and then OK appears. SWITCH LEFT * On single click, OK appears. SWITCH RIGHT * On single click, OK appears. 2) If all items are OK: The test terminates when the OK is returned for the final item (SWITCH RIGHT). The program returns to the test menu screen, and an appears in the left column. The cursor advances to the next test in the menu. 3) If the test returns an NG: Press CANCEL . The program returns to the test menu screen, and an NG appears in the left column. The cursor does not advance. 5-2-16 CD-RW Drive-Connection Test (16 CD-RW) (1) Display (Test Screen Type C) 1) Test name CD-RW (2) Test Content 1) Checks the internal (SCSI) CD-RW drive interface. (3) Judgment 1) Exit-method area EXIT: [ENTER / CANCEL] Result area ... OK Press ENTER to return to the test menu screen. An the next test in the menu. 2) Result area ... NG NG message NG message INTERNAL SCSI a) Problem accessing the internal CD-RW drive. Press CANCEL . The program returns to the test menu screen, and an NG appears in the left column. The cursor does not advance. 5-2-17 Word-Clock I/O Test (17 W.CLK I/O) (1) Display (Test Screen Type B) 1) Test name W.CLK I/O (2) Test Content 1) Checks the word-clock generator functions (X'tal OSC, VCI, I/O). appears in the left column, and the cursor advances to
84
AW4416
(3) Judgment 1) Prompt area Exit-method area
MAKE TEST LOOP AND PRESS ENTER EXIT: [ENTER / CANCEL]
Start the test by pressing ENTER . 2) If result area OK Press ENTER to return to the test menu. An appears in the left column, and the cursor advances to the next
test in the menu. 3) If