Text preview for : Yamaha-MCX2000 audioserver.pdf part of Yamaha MCX2000 audio server
Back to : Yamaha-MCX2000 audioserve | Home
DIGITAL AUDIO SERVER
MCX-2000 SERVICE MANUAL
IMPORTANT NOTICE
This manual has been provided for the use of authorized YAMAHA Retailers and their service personnel.
It has been assumed that basic service procedures inherent to the industry, and more specifically YAMAHA Products, are already known and understood by the users,
and have therefore not been restated.
WARNING: Failure to follow appropriate service and safety procedures when servicing this product may result in personal injury, destruction of expensive
components, and failure of the product to perform as specified. For these reasons, we advise all YAMAHA product owners that any service required
should be performed by an authorized YAMAHA Retailer or the appointed service representative.
IMPORTANT: The presentation or sale of this manual to any individual or firm does not constitute authorization, certification or recognition of any applicable
technical capabilities, or establish a principle-agent relationship of any form.
The data provided is believed to be accurate and applicable to the unit(s) indicated on the cover. The research, engineering, and service departments of YAMAHA are
continually striving to improve YAMAHA products. Modifications are, therefore, inevitable and specifications are subject to change without notice or obligation to
retrofit. Should any discrepancy appear to exist, please contact the distributor's Service Division.
WARNING: Static discharges can destroy expensive components. Discharge any static electricity your body may have accumulated by grounding yourself to the
ground buss in the unit (heavy gauge black wires connect to this buss).
IMPORTANT: Turn the unit OFF during disassembly and part replacement. Recheck all work before you apply power to the unit.
I CONTENTS
TO SERVICE PERSONNEL ...................................... 2~4 ENTERING SYSTEM ID 27~28
PREVENTION OF ELECTROSTATIC DISCHARGE .... 5 TROUBLESHOOTING 29
FRONT PANELS ............................................................ 6 30
REAR PANELS .......................................................... 6~7 ERROR CODE AND RECOVERY
REMOTE CONTROL PANEL ........................................ 8 31
SPECIFICATIONS ...................................................... 8~9 TEST MODE 32~33
INTERNAL VIEW ........................................................... 9 IC DATA ................................................................. 34~41
DISASSEMBLY PROCEDURES / .......... 10~18 BLOCK DIAGRAM ....................................................... 43
SERVICE PRECAUTIONS PRINTED CIRCUIT BOARD .................................. 44~49
19 PIN CONNECTION DIAGRAM .................................... 50
UPDATING FIRMWARE SCHEMATIC DIAGRAM ........................................ 51~62
MCX-2000
19~20 PARTS LIST ........................................................... 63~76
RECOVERY AFTER REPLACING CD-R/RW DRIVE REMOTE CONTROL .................................................... 77
20 DIRECTION FOR USE
RECOVERY AFTER REPLACING HDD Welcome to MusicCAST .................................. 78~81
21~23 Preface ............................................................... 81~83
RECOVERY AFTER REPLACING MAIN P.C.B. Preparations and Setup ................................... 83~96
24 About Digital Recording with MusicCAST ........... 96
SERVICE MENU 25~26 Glossary .................................................................. 97
100958 2005 All rights reserved.
This manual is copyrighted by YAMAHA and may not be copied or
redistributed either in print or electronically without permission.
P.O.Box 1, Hamamatsu, Japan
'05.11
MCX-2000
I TO SERVICE PERSONNEL
AC LEAKAGE
1. Critical Components Information WALL EQUIPMENT TESTER OR
Components having special characteristics are marked s OUTLET UNDER TEST EQUIVALENT
and must be replaced with parts having specifications equal
to those originally installed.
2. Leakage Current Measurement (For 120V Models Only)
When service has been completed, it is imperative to verify
that all exposed conductive surfaces are properly insulated
INSULATING
from supply circuits.
TABLE
G Meter impedance should be equivalent to 1500 ohms shunted
by 0.15µF.
G Leakage current must not exceed 0.5mA.
G Be sure to test for leakage with the AC plug in both polarities.
THE COMPACT DISC RECORDER SHOULD NOT BE ADJUSTED OR REPAIRED BY ANYONE EXCEPT PROPERLY QUALIFIED
SERVICE PERSONNEL.
WARNING: CHEMICAL CONTENT NOTICE!
The solder used in the production of this product contains LEAD. In addition, other electrical/electronic and /or plastic
(where applicable) components may also contain traces of chemicals found by the California Health and Welfare Agency
(and possibly other entities) to cause cancer and/or birth defects or other reproductive harm.
DO NOT PLACE SOLDER, ELECTRICAL/ELECTRONIC OR PLASTIC COMPONENTS IN YOUR MOUTH FOR ANY REA-
SON WHATSOEVER!
Avoid prolonged, unprotected contact between solder and your skin! When soldering, do not inhale solder fumes or expose
eyes to solder/flux vapor!
If you come in contact with solder or components located inside the enclosure of this product, wash your hands before
handling food.
About Lead Free Solder /
The P.C.B.s installed in this unit are soldered using the
following solder.
Side A / Side B /
MAIN P.C.B. Lead Free Solder / Lead Free Solder /
OPERATION P.C.B. Lead Free Solder / Lead Free Solder /
Side A SMT REFLOW Process
Solder Dip
Side B MI FLOW Process
MCX-2000
Among some types of lead free solder currently available,
it is recommended to use one of the following types for the
repair work.
· Sn + Ag + Cu (tin + silver + copper)
· Sn + Cu (tin + copper)
· Sn + Zn + Bi (tin + zinc + bismuth)
1. As the melting point temperature of the lead free solder
is about 30°C to 40°C (50°F to 70°F) higher than that of
the lead solder, be sure to use a soldering iron suitable
to each solder.
2. If lead solder must be used, be sure to remove lead free
solder from each terminal section of the parts to be
replaced and from the area around it completely before
soldering, or make sure that the lead free solder and
lead solder melt together fully.
2
MCX-2000
WARNING: Laser Safety
This product contains a laser beam component. This component may emit invisible, as well as visible radiation, which may
cause eye damage. To protect your eyes and skin from laser radiation, the following precautions must be used during
servicing of the unit.
1) When testing and/or repairing any component within the product, keep your eyes and skin more than 30 cm away from
the laser pick-up unit at all times. Do not stare at the laser beam at any time.
2) Do not attempt to readjust, disassemble or repair the laser pick-up, unless noted elsewhere in this manual.
3) CAUTION: Use of controls, adjustments or performance of procedures other than those specified herein may result in
hazardous radiation exposure.
Laser Emitting conditions:
1. This device is a Class IIIb laser device.
Class IIIb means
With the protective case removed, exposure to the light output from the laser, either directly or reflected by a mirror, can
cause harm to the eyes, but there is no danger to the eyes from exposure to dispersed reflected laser light. (Generally 0.5
W or less)
2. Always wear eyeglasses designed for protection against laser light.
3. Always wear gloves.
4. Have no reflective objects anywhere near this device.
5. Figure A shows from where in this device the laser is emitted.
6. When switching on the power to the device for the first time, always measure the laser power with a laser power meter
and check that the power is no greater than the number of Watts in the specifications.
7. Never look directly at the laser light while the laser is emitting light.
8. Do not allow the laser light to shine directly on your skin while the laser is emitting light.
PROTECTION OF EYES FROM LASER BEAM DURING SERVICING
This set employs a laser. Therefore, be sure to carefully Laser Radiation Point
follow the instructions below when servicing.
1. Laser Diode Properties
· Material : GaAlAs
· Wavelength : 780-787 nm
· Emission Duration : Pulse
· Laser Output : DC erase mode max. 12 mW (Continuous)
Write mode max. 70 mW
(Max. Cycle 98 ns, Min. Cycle 27 ns at Max. Speed)
This output is the value measured at the lens of the Laser Pickup
Unit.
MCX-2000
2. When checking the laser diode emission, keep your eyes more than
30 cm away from the objective lens.
CAUTION
Use of controls or adjustments or performance of procedures other than those specified herein may result in hazardous
radiation exposure.
3
MCX-2000
CAUTION
Use of controls or adjustments or performance of
procedures other than those specified herein may
result in hazardous radiation exposure.
ATTENTION
L'emploi de commandes, de réglages ou un choix de
procédures différents des spécifications de cette
brochure peut entraîner une exposition à d'éventuelles FM ANT
WE87940C0
MODEL NO. MCX2000
WARNING : TO REDUCE THE RISK OF FIRE
OR ELECTRIC SHOCK, DO NOT EXPOSE THIS
APPLIANCE TO RAIN OR MOISTURE.
XM RADIO RS232C 100240V, 0.50.3A, 50/60Hz
radiations pouvant être dangereses.
AC IN
W_LAN ANT 75UNBAL. MADE IN MALAYSIA
IN OUT THIS CLASS B DIGITAL APPARATUS COMPLIES WITH
VIDEO L CANADIAN ICE-003.
CET APPAREIL NUMÉRIQUE DE LA CLASSE B EST CONFORME
S À LA NORME NMB-003 DU CANADA.
VIDEO
IN OUT R
CLASS 1 LASER PRODUCT
OPTICAL ANALOG ® LASER KLASSE 1 PRODUKT
LINK/DATA 10/100 IN
IC: 740BMCX2000A
VIDEO LAN REMOTE AUDIO
ACHTUNG
(C model)
Die Verwendung von Bedienungselementen oder
Einstellungen oder die Durchführung von
Bedienungsvorgängen, die nicht in dieser Anleitung
aufgeführt sind, kann zu einem Kontakt mit
gefährlichen Laserstrahlen führen.
OBSERVERA
Användning av kontroller och justeringar eller
genomförande av procedurer andra än de som
specificeras i denna bok kan resultera i att du utsätter
dig för farlig strålning.
WE87960GB0
FM ANT
ATTENZIONE W_LAN ANT
RS232C
75UNBAL.
IN OUT
MODEL NO. MCX2000
100240V, 0.50.3A, 50/60Hz
MADE IN MALAYSIA
AC IN
VIDEO L
Uso di controlli o regolazioni o procedure non S
VIDEO
VIDEO
LINK/DATA
LAN
10/100 IN
REMOTE
IN
OPTICAL
OUT
AUDIO
ANALOG
R
CLASS 1 LASER PRODUCT
LASER KLASSE 1 PRODUKT
LUOKAN 1 LASERLAITE
KLASS 1 LASER APPART
PRODUIT LASER DE CLASSE 1
specificamente descritte può causare l'esposizione a
radiazioni di livello pericoloso. (B, G models)
PRECAUCIÓN
El uso de los controles o los procedimientos de ajuste
o utilización diferentes de los especificados en este
manual pueden causar una exposiciónpeligrosa a la
radiación.
VOORZICHTIG
Gebruik van bedieningsorganen of instellingen, of
uitvoeren van handelingen anders dan staan
beschreven in deze handleiding kunnen leiden tot
blootstelling aan gevaarlijke stralen.
VARO!
AVATTAESSA JA SUOJALUKITUS OHITETTAESSA
OLET ALTTIINA NÄKYMÄTTÖMÄLLE
MCX-2000
LASERSÄTEILYLLE. ÄLÄ KATSO SÄTEESEEN.
VARNING!
OSYNLIG LASERSTRÅLNING NÄR DENNA DEL ÄR
ÖPPNAD OCH SPÄRREN ÄR URKOPPLAD.
BETRAKTA EJ STRÅLEN.
4
MCX-2000
I PREVENTION OF ELECTROSTATIC DISCHARGE
Some semiconductor (solid state) devices can be damaged easily by static electricity. Such components commonly are called
Electrostatically Sensitive (ES) Devices. Examples of typical ES devices are integrated circuits and some field-effect transistors and
semiconductor "chip" components. The following techniques should be used to help reduce the incidence of component damage caused by
electro static discharge (ESD).
1. Immediately before handling any semiconductor component or semiconductor-equipped assembly, drain off any ESD on your body by
touching a known earth ground. Alternatively, obtain and wear a commercially available discharging ESD wrist strap, which should be
removed for potential shock reasons prior to applying power to the unit under test.
2. After removing an electrical assembly equipped with ES devices, place the assembly on a conductive surface such as aluminum foil, to
prevent electrostatic charge buildup or exposure of the assembly.
3. Use only a grounded-tip soldering iron to solder or unsolder ES devices.
4. Use only an anti-static solder removal device. Some solder removal devices not classified as "anti-static (ESD protected)" can generate
electrical charge sufficient to damage ES devices.
5. Do not use freon-propelled chemicals. These can generate electrical charges sufficient to damage ES devices.
6. Do not remove a replacement ES device from its protective package until immediately before you are ready to install it. (Most
replacement ES devices are packaged with leads electrically shorted together by conductive foam, aluminum foil or comparable
conductive material).
7. Immediately before removing the protective material from the leads of a replacement ES device, touch the protective material to the
chassis or circuit assembly into which the device will be installed.
CAUTION: Be sure no power is applied to the chassis or circuit, and observe all other safety precautions.
8. Minimize bodily motions when handling unpackaged replacement ES devices. (Otherwise harmless motion such as the brushing
together of your clothes fabric or the lifting of your foot from a carpeted floor can generate static electricity (ESD) sufficient to damage an
ES device).
Grounding for electrostatic breakdown prevention
1. Human body grounding:
Use an anti static wrist strap to discharge the static electricity
Anti-static wrist strap
from your body.
2. Work table grounding: 1M
Put a grounded conductive material (sheet) or iron sheet on
the area where the optical pickup is placed.
Caution:
The static electricity of your clothes will not be grounded
through the wrist strap. So take care not to let your clothes Conductive material
(sheet) or iron sheet
touch the optical pickup.
MCX-2000
5
MCX-2000
I FRONT PANELS
U, C models
A, B, G, J models
I REAR PANELS
U model
MCX-2000
6
MCX-2000
C model
A model
B, G models
J model
MCX-2000
7
MCX-2000
Video Output /
I REMOTE CONTROL PANEL Video Signal Level .......................................... 1 Vp-p/75 ohms
S-Video Signal Level
Y ..................................................................... 1 Vp-p/75 ohms
C (U, C, J models) .................................. 0.286 Vp-p/75 ohms
C (A, B, G models) ..................................... 0.3 Vp-p/75 ohms
FM TUNER /
Tuning Range /
U, C models ................................................ 87.5 to 107.9 MHz
A, B, G models ........................................ 87.50 to 108.00 MHz
J model ......................................................... 76.0 to 90.0 MHz
Frequency Step /
U, C models ................................................................ 0.2 MHz
A, B, G models .......................................................... 0.05 MHz
J model ....................................................................... 0.1 MHz
GENERAL /
Application Disks /
..... CD, CD-ROM (MP3 only), AUDIO CD-R, AUDIO CD-RW
Support MP3 Format /
The file extension is MP3 or mp3.
MPEG1/ 2 Layer3 100% compression bit rate is applicable.
Based on ID3 Tag ver. 1.1.
HDD Capacity /
..................................................................................... 160 GB
LAN Interface /
.......................................................... Ethernet 10/100 Base-T
I SPECIFICATIONS / Wireless Interface /
...................................................................... IEEE 802.11 b/g
Power Supply /
AUDIO PERFORMANCE /
U, C models ................................................... AC 120 V, 60 Hz
Output Level / (1 kHz, 0 dB) A, B, G models ....................................... AC 100-240 V, 50 Hz
............................................................................ 2 ± 0.5 Vrms J model ..................................................... AC 100 V, 50/60 Hz
Frequency Characteristics / (EIAJ)
Power consumption /
....................................................... 20 Hz to 20 kHz, ± 0.5 dB
Standby ................................................................... 5 W or less
Signal to Noise Ratio / (EIAJ) CD Store .......................................................................... 30 W
Playback .......................................................... 100 dB or more
Recording ........................................................... 92 dB or more Operating Temperature /
....................................................................... +5 °C to +35 °C
Dynamic Range / (EIAJ)
Weight / (without Package)
Playback .......................................................... 100 dB or more ................................................................ 6.6 kg (14 lbs. 9 oz.)
Recording ........................................................... 92 dB or more
Maximum Dimensions / (W x H x D)
Total Harmonic Distortion / (EIAJ) ............. 435 x 95.5 x 408.5 mm (17-1/8" x 3-3/4" x 16-1/16")
Playback .......................................................... 0.004 % or less Panel Color /
Recording ......................................................... 0.006 % or less Black Color ......................................... U, C, A, B, G, J models
Silver Color .................................................................. J model
INPUT/OUTPUT / Titanium Color ...................................................... B, G models
MCX-2000
Line Output / Accessories /
Output Level ................................................................. 2 Vrms Remote Control x 1, Battery (Manganese) x 2, Optical Cable x 1,
Output Resistance .................................................... 600 ohms Audio Pin Cable x 1, Video Pin Cable x 1, Indoor FM Antenna x 1,
Line Input / Power Cable x 1, CAT-5 Straight Cable x 1, Upgrade CD-ROM x 1
Input Sensitivity ..................................................... 150 mVrms
Input Impedance ...................................................... 22 k-ohms
* Specifications are subject to change without notice due to product
Digital Output / improvements.
Optical Output Level ................................................... -20 dBm
Sampling Frequency ................................................... 44.1 kHz
Digital Input / U .......... U.S.A. model C ...... Canadian model
Optical Input Level ...................................................... -20 dBm A .......... Australian model B ...... British model
Input Gain (with Digital Volume) ................................... ±12 dB G .......... European model J ....... Japanese model
Input Gain (without Digital Volume) ............................... ±0 dB
Sampling Frequency Tolerance
.................................... 32 kHz, 44.1 kHz, 48 kHz and 96 kHz
Headphone Output / (Phones Level Max.) The XM name and related logos are registered trademarks of
Output Level (-20 dB, 150 ohms load) ................. 430 mVrms XM Satellite Radio Inc.
8
MCX-2000
· DIMENSIONS
(1-3/8")
35.5
408.5 (16-1/16")
370 (14-9/16") 3
(3-1/8") (2-3/8") (1/8")
435 (17-1/8")
60
155.5 (6-1/8")
(3-3/4")
95.5
80
Unit: mm (inch)
15.5
(5/8")
I INTERNAL VIEW
1 2 3 4 5 6
1 DC FAN
2 POWER SUPPLY UNIT
3 OPERATION (2) P.C.B.
4 FM / AM TUNER
5 MAIN (1) P.C.B.
6 MAIN (2) P.C.B.
MCX-2000
7 CDR UNIT
8 OPERATION (3) P.C.B.
9 HDD UNIT
0 WIRELESS LAN CARD
A OPERATION (4) P.C.B.
B OPERATION (1) P.C.B.
7 8 9 0
A B
9
MCX-2000
I DISASSEMBLY PROCEDURES
(Remove parts in the order as numbered.)
Disconnect the power cable from the AC power outlet.
1. Removal of Top Cover
a. Remove 4 screws (1), 4 screws (2) and 1 screw (3). 1 2 3
(Fig. 1)
b. Remove 1 screw (4). (Fig. 1) 4
c. Remove the top cover rearward while lifting it up. (Fig.
1)
T10 2.7 mm When removing the screw 4, use
the special screwdriver with tip
shaped in figure. As the screw 4
has a lug at its center, use the one
with a hole.
With hole
Lug
Without hole
Top Cover
2
4
1 2
3
1
MCX-2000
Fig. 1
10
MCX-2000
* Removal of Wireless LAN Module
a. Remove two Antenna connectors by using U.FL
removing tool. (Fig. A)
b. Expand the hook two places right and left, and detach
wireless LAN module to the right. (Fig. A)
* Be sure to connect the LAN antenna connector Hook
to the original position.
Dipole Antenna Ass'y
LAN Antenna Connector *
Wireless LAN Module
Black
Hook
Gray
Reverse F Antenna
Fig. A
CAUTION !
· To remove the LAN antenna connector, use the U.FL
removing tool. Hook the tip of this tool on the cover of
the connector and pull it
straight in the direction of
the engaging axis of the
connector.
Special removing tool
AAX72980: U.FL removing tool
· When installing the connector, insert it vertically with
respect to the wireless LAN module as it is removed
from the MAIN (1) P.C.B..
· The connector can be inserted and removed up to 5
times only.
MCX-2000
· Be sure to connect the LAN antenna connector to the
original position. (Fig. A)
11
MCX-2000
2. Removal of Front Panel Unit
a. Remove 6 screws (5) and 6 screws (6). (Fig. 2) 5 6
b. Remove CB901. (Fig. 2)
c. Remove the front panel unit forward. (Fig. 2)
Front Panel Unit TO MAIN (1) P.C.B
CB901
Flexible flat cable
5
Blue seal
6 CB901
TO OPERATION (1) P.C.B
CB205
* Install the flexible flat cable with the blue seal being located
CB205 side and left side.
Fig. 2
3. Removal of MAIN (1) and (2) P.C.B.
a. Remove 6 screws (7). (Fig. 3) 7
b. Remove the Angle/Chassis. (Fig. 3)
c. Remove 1 screw (8) and 2 Jack screws (9). (Fig. 4) 8 9
d. Remove CB850. (Fig. 5)
e. Remove the MAIN (2) P.C.B..
Angle / Chassis
/
MAIN (2) P.C.B
7
MCX-2000
7
C B
MAIN (1) P.C.B
7
Fig. 3
12
MCX-2000
f. Remove 3 screws (0) and 3 screws (A). (Fig. 4) 0 A
g. Remove 2 screws (B) and 2 screws (C). (Fig. 3) B C
h. Remove CB201, CB501~CB5004 and CB904. (Fig. 5)
i. Remove the MAIN (1) P.C.B..
8 9
0 A
Fig. 4
CB501
CB503
CB502
MAIN (1) P.C.B
CB504
CB201
CB850
MAIN (2) P.C.B CB904
Fig. 5
MCX-2000
13
MCX-2000
When checking the P.C.B.:
· The cloth for insulation purpose on this unit, where
P.C.B. is stood on it and checks it. (Fig. 6)
· Reconnect all cables (connectors) that have been
disconnected.
Be sure to use the extension cable for servicing for the
following section.
MAIN (1) P.C.B. CB504 OPERATION (2) P.C.B. CB7:
WC028700 (30P 250mm P=0.5)
MAIN (1) P.C.B. CB901 OPERATION (1) P.C.B. CB205:
MFA28160 (28P 160mm P=1.0)
· When connecting the cable, use care for the polarity.
· In this unit, the ground of MAIN (1) P.C.B. is connected
to the Rear Panel. When MAIN (1) P.C.B. is removed
from the Rear Panel, connect the ground to the rear
panel or chassis, using a lead wire or the like. (Fig. 6)
Earth (lead wire)
ST601
MAIN (1) P.C.B.
MFA28160
MAIN (2) P.C.B.
Cloth
WC028700
Fig. 6
MCX-2000
4. Removal of CDR Unit
a. Disconnect the power cable and IDE cable from the
CDR unit. (Fig. 8)
b. Remove 2 screws (D), 4 screws (E) and 1 screw (F). D E F
(Fig. 7)
c. Remove the CDR unit rearward while lifting it up. (Fig. 7)
* The CDR unit is fixed with the hook in two places.
(Fig. 7)
14
MCX-2000
HOOK
CDR Unit
CDR
IDE Cable
D
Power Cable
E
E
F
Fig. 7
CDR
CDR
Fig. 8
5. Disassembly of CDR Unit
a. Remove 6 screws (G) and then remove the Support G
CDR. (Fig. 9)
b. Push the right side of the manual eject lever to open the
tray and remove the lid upward. (Fig. 9, 10)
Support CDR
CD-R/RW Drive
CD-R/RW
G
MCX-2000
Volume : Low /
Volume Control Manual Eject Lever
Lid / Tray
Note) To open the tray, push the right side ( section)
G of the manual eject lever.
Support CDR
CDR Unit
Fig. 9 Fig. 10
15
MCX-2000
DC INPUT
DIGITAL Jumper pin in the master state IDE Interface Connector
AUDIO
OUT
Fig. 11
6. Assembly of CDR Unit
a. Set the plastic shunt of the new CD-R/RW drive to the
master position. (Fig. 11)
b. Set the Volume control to the minimum position (fully to
the left). (Fig. 10)
c. Push the right side of the manual eject lever to open the
tray and install the lid. (Fig. 9, 10)
d. Install the Support CDR using 6 screws marked (G). G
(Fig. 9)
7. Installation of CDR Unit
a. Connect the power cable and IDE cable to the CDR
unit. (Fig. 8)
b. Install the CDR unit. (Fig. 7)
c. Install 2 screws (D), 4 screws (E) and 1 screw (F). D E F
(Fig. 7)
HDD Replacement
a. Remove 6 screws (H). (Fig. 12) H
b. Remove the Bottom Cover HDD. (Fig. 12)
H
MCX-2000
Bottom Cover HDD
H
Fig. 12
16
MCX-2000
Damper HDD
IDE Cable
IDE
Power Cable
Fig. 13
HDD Unit
HDD
Damper HDD
Mounter
Damper HDD
I I
Fig. 14
c. Disconnect the IDE cable and power cable from the
HDD unit. (Fig. 13)
d. Remove the HDD unit. (Fig. 13)
* The HDD unit is fixed by damper HDD in three
MCX-2000
places.
* Be careful not to hook the IDE cable and the power
cable over the HDD tray.
* Static electricity can damage the HDD. Be careful
not to touch the terminal pins and the P.C.B..
e. Remove 4 screws (I). (Fig. 14)
f. Remove the HDD. (Fig. 14) I
g. Set the plastic shunt of the new HDD to Cable select.
(Fig. 15)
* It is necessary to set the HDD to MASTER, SLAVE
or Cable select when connecting the HDD to the
component you plan to use. This unit is designed to
operate HDD when it is set to Cable select. Usually,
setting procedure is written on the HDD itself.
17
MCX-2000
Example: When setting the WD1600BB model Example: When setting the ST3160021A model
Plastic Shunt Plastic Shunt
The HDD is set to Cable select by setting the plastic The HDD is set to Cable select by setting the plastic
shunt at the first position from right of the jumper switch. shunt at the second position from left of the jumper
switch.
Fig. 15
h. Install a new HDD on the mounter using 4 screws (I) . I
(Fig. 14)
* HDD is a very sensitive device. Be careful not to give
any shock to it.
i. The IDE cable and power cable are inserted in the HDD
unit. (Fig. 16)
* Make sure that the connectors are in the correct
direction, and connect the cables securely.
* Static electricity can damage the HDD. Be careful
not to touch the terminal pins and the circuit board.
j. Install the HDD unit. (Fig. 16)
* The HDD unit is fixed by damper HDD in three
places.
k. Install the Bottom Cover HDD. (Fig. 12)
l. Install 6 screws (H). (Fig. 12)
H
Damper HDD
IDE Cable
IDE
MCX-2000
Power Cable
Fig. 16
18
MCX-2000
I SERVICE PRECAUTIONS
1. When updating the firmware only without replacing any
part, refer to "UPDATING FIRMWARE". (p. 19~20)
2. After replacing the CD-R/RW Drive, refer to "RECOVERY
AFTER REPLACING CD-R/RW DRIVE". (p. 20)
3. After replacing HDD, refer to "RECOVERY AFTER RE-
PLACING HDD". (p. 21~23)
4. After replacing the Main P.C.B., refer to "RECOVERY
AFTER REPLACING MAIN P.C.B.". (p. 24)
I UPDATING FIRMWARE
Updating the firmware requires use of the Update CD.
* More information on supply of the Update CD will be
provided in the Service News.
· Items required
Update CD
· Operation Procedure
Perform following steps while watching the display screen
of the main unit and using the keys of the main unit.
1) Turn on the power.
f
2) The [TOP MENU] is displayed.
3) Press the "v" key to open the tray, set the Update CD
on the tray and then close the tray.
4) Using the "Cursor Controller" key, select the menu
items as follows.
[Setup]
[System Utilities] M
[System Update]
5) Press the "Cursor Controller M" key.
6) Using the "Cursor Controller" key, select the [Start].
The updating function starts.
MCX-2000
During downloading
After updating, the message as shown below is dis-
played.
19
MCX-2000
7) Press the "v" key to open the tray, remove the Update f
CD and close the tray.
8) Press "STANDBY/ON" key to restart.
9) Confirm the version of the firmware.
Using the "Cursor Controller" key, select the menu
items as follows.
[Setup]
[System Utilities]
[System Information]
[Version]
When the displayed firmware version is the same as
the firmware version recorded in the Update CD, the
procedure is completed.
10)Press the "STANDBY/ON" key to turn off the power.
I RECOVERY AFTER REPLACING CD-R/RW DRIVE
After replacing the CD-R/RW drive, perform the recovery
procedure as described below.
· Items required
Rescue CD
· Operation Procedure
Perform following steps while watching the display screen
of the main unit and using the keys of the main unit.
1) Turn on the power.
The message as shown below is displayed.
2) Press the "v" key to open the tray, set the Rescue CD f
on the tray and then close the tray.
The updating function starts automatically.
3) After updating, the message as shown below is dis-
played.
MCX-2000
During downloading
4) Press the "v" key to open the tray, remove the Rescue f
CD and close the tray.
5) Press the "STANDBY/ON" key.
The power to the main unit is turned OFF and then
turned ON automatically.
20
MCX-2000
I RECOVERY AFTER REPLACING HDD
After replacing the HDD, perform the recovery procedure
as described below.
· Items required
FORMAT and Recovery CD (HDD is formatted.)
Rescue CD (HDD is not formatted.)
· Operation Procedure
Perform following steps while watching the display screen
of the main unit and using the keys of the main unit.
Case 1
· When a brand new HDD is installed.
· When an HDD used for a PC or other MCX-2000 is
installed.
Note) In this case, for the purpose of copyright pro-
tection, HDD cannot be used unless all the data
recorded in it is erased.
1) Turn on the power.
The message as shown below is displayed.
2) Press the "v" key to open the tray, set the FORMAT f
and Recovery CD on the tray and then close the tray.
Note) The data recorded in HDD is completely erased.
The updating function starts automatically.
3) After updating, the message as shown below is dis-
played.
MCX-2000
During downloading
4) Press the "v" key to open the tray, remove the FOR- f
MAT and Recovery CD and close the tray.
5) Press the "STANDBY/ON" key.
The power to the main unit is turned OFF and then
turned ON automatically.
21
MCX-2000