Text preview for : Yamaha-02R96E digimix.pdf part of Yamaha 02R96E digital mixer
Back to : Yamaha-02R96E digimix.par | Home
02R96
DIGITAL MIXING CONSOLE/ PEAK METER BRIDGE/WOODEN SIDE PANELS
/MB02R96/SP02R96
SERVICE MANUAL
CONTENTS SPECIFICATIONS ................................................... 4 DIMENSIONS .......................................................... 16 PANEL LAYOUT .................................. 17 CIRCUIT BOARD LAYOUT ............... 30 DISASSEMBLY PROCEDURE ............................ 34 INSTALLING I/O CARDS ....................... 52 LSI PIN DESCRIPTION ................................ 53 IC BLOCK DIAGRAM .................................. 64 CIRCUIT BOARDS ....................................... 71 INSPECTIONS ................................................... 134/144 SERVICE CHECK PROGRAM . 154/164 TEST PROGRAM ......................... 174/175 USING BULK DUMP ....................... 176 CHECKING THE BATTERY ................ 177 MIDI DATA FORMAT ............... 178 MIDI IMPLEMENTATION CHART ............................ 193 PARTS LIST BLOCK DIAGRAM OVERALL CONNECTOR CIRCUIT DIAGRAM
This document is printed on chlorine free (ECF) paper with soy ink.
CIRCUIT DIAGRAM
PA 011640
HAMAMATSU, JAPAN
1.29K-6096 Printed in Japan '02.06
1
02R96
IMPOR TANT NOTICE
This manual has been provided for the use of authorized Yamaha Retailers and their service personnel. It has been assumed that basic service procedures inherent to the industry, and more specifically Yamaha Products, are already known and understood by the users, and have therefore not been restated.
WARNING :
Failure to follow appropriate service and safety procedures when servicing this product may result in personal injury, destruction of expensive components and failure of the product to perform as specified. For these reasons, we advise all Yamaha product owners that all service required should be performed by an authorized Yamaha Retailer or the appointed service representative. This presentation or sale of this manual to any individual or firm does not constitute authorization certification, recognition of any applicable technical capabilities, or establish a principal-agent relationship of any form.
IMPORTANT :
The data provided is belived to be accurate and applicable to the unit(s) indicated on the cover. The research engineering, and service departments of Yamaha are continually striving to improve Yamaha products. Modifications are, therefore, inevitable and changes in specification are subject to change without notice or obligation to retrofit. Should any discrepancy appear to exist, please contact the distributor's Service Division.
WARNING : IMPORTANT :
Static discharges can destroy expensive components. Discharge any static electricity your body may have accumulated by grounding yourself to the ground bus in the unit (heavy gauge black wires connect to this bus.) Turn the unit OFF during disassembly and parts replacement. Recheck all work before you apply power to the unit.
WARNING: CHEMICAL CONTENT NOTICE!
The solder used in the production of this product contains LEAD. In addition, other electrical/electronic and/or plastic (Where applicable) components may also contain traces of chemicals found by the California Health and Welfare Agency (and possibly other entities) to cause cancer and/or birth defects or other reproductive harm. DO NOT PLACE SOLDER, ELECTRICAL/ELECTRONIC OR PLASTIC COMPONENTS IN YOUR MOUTH FOR ANY REASON WHAT SO EVER! Avoid prolonged, unprotected contact between solder and your skin! When soldering, do not inhale solder fumes or expose eyes to solder/flux vapor! If you come in contact with solder or components located inside the enclosure of this product, wash your hands before handling food.
WARNING: THIS APPARATUS MUST BE EARTHED
IMPORTANT
THE WIRES IN THIS MAINS LEAD ARE COLOURED IN ACCORDANCE WITH THE FOLLOWING CODE: GREEN-AND-YELLOW : BLUE : BROWN : EARTH NEUTRAL LIVE
As the colours of the wires in the mains lead of this apparatus may not correspond with the coloured markings identifying the terminals in your plug, proceed as follows: The wire which is coloured GREEN and YELLOW must be connected to the terminal in the plug which is marked by the letter E or by the safety earth symbol or coloured GREEN and YELLOW. The wire which is coloured BLUE must be connected to the terminal which is marked with the letter N or coloured BLACK. The wire which is coloured BROWN must be connected to the terminal which is marked with the letter L or coloured RED. * This applies only to products distributed by YAMAHA KEMBLE MUSIC (U.K.) LTD.
WARNING
Components having special characteristics are marked originally installed. and must be replaced with parts having specification equal to those
2
02R96
LITHIUM BATTERY HANDLING
This product uses a lithium battery for memory back-up. WARNING : Lithium batteries are dangerous because they can be exploded by improper handling. Observe the following precautions when handling or replacing lithium batteries. Leave lithium battery replacement to qualified service personnel. Always replace with batteries of the same type. When installing on the PC board by soldering, solder using the connection terminals provided on the battery cells. Never solder directly to the cells. Perform the soldering as quickly as possible. Never reverse the battery polarities when installing. Do not short the batteries. Do not attempt to recharge these batteries. Do not disasemble the batteries. Never heat batteries or throw them into fire.
ADVARSEL!
Lithiumbatteri-Eksplosionsfare ved fejlagtig handtering. Udskiftning ma kun ske med batteri af samme fabrikat og type. lever det brugte batteri tilbage til leverandren.
VARNING
Explosionsfara vid felaktigt batteribyte. Anvand samma batterityp eller en ekvivalent typ som rekommenderas av apparattillverkaren. Kassera anvant batteri enligt fabrikantens instruktion.
VAROITUS
Paristo voi rajahtaa, jos se on virheellisesti asennettu. Vaihda paristo ainoastaan laitevalmistajan suosittelemaan tyyppiiin. Havita kaytetty paristo valmistajan ohjeiden mukaisesti. The following information complies with Dutch official Gazette 1995. 45; ESSENTIALS OF ORDER ON THE COLLECTION OF BATTERIES. · Please refer to the diassembly procedure for the removal of Back-up Battery. · Leest u voor het verwijderen van de backup batterij deze beschrijving.
Take care not to trap your fingers.
3
02R96
SPECIFICATIONS
02R96
General Spec
Number of scene memories Internal Sampling Frequency External Signal Delay Fader Fader Resolution Total Harmonic Distortion*1 (CH INPUT to STEREO OUT) (Input Gain=Min.) Frequency Response (CH INPUT to STEREO OUT) Dynamic Range (maximum level to noise level) fs=48 kHz fs=96 kHz 99 44.1 kHz, 48 kHz, 88.2 kHz, 96 kHz Normal rate: 44.1 kHz10% to 48 kHz+6% Double rate: 88.2 kHz10% to 96 kHz+6% Less than 2.0 ms CH INPUT to STEREO OUT (fs=48 kHz) Less than 1.1 ms CH INPUT to STEREO OUT (fs=96 kHz) 100 mm motorized with touch sense × 25 +10 to 96, dB (256 steps/100 mm) input faders 0 to 130, dB (256 steps/100 mm) master faders, stereo fader Less than 0.05% 20 Hz to 20 kHz @ +14 dB into 600 Less than 0.01% 1 kHz @ +18 dB into 600 (fs=48 kHz) Less than 0.05% 20 Hz to 40 kHz @ +14 dB into 600 Less than 0.01% 1 kHz @ +18 dB into 600 20 Hz20 kHz, 0.5, 1.5 dB @ +4 dB into 600 (fs=48 kHz) 20 Hz40 kHz, 0.5, 1.5 dB @ +4 dB into 600 (fs=96 kHz) 110 dB typ. DA Converter (STEREO OUT) 105 dB typ. AD+DA (to STEREO OUT) @ fs=48 kHz 105 dB typ. AD+DA (to STEREO OUT) @ fs=96 kHz Hum & Noise *2 (20 Hz20 kHz) 128 dB Equivalent Input Noise 92 dB residual output noise. STEREO OUT (STEREO OUT off) 92 dB (96 dB S/N) STEREO OUT (STEREO fader at nominal level and all CH INPUT faders at minimum level) 64 dB (68 dB S/N) STEREO OUTPUT (STEREO fader at nominal level and one CH INPUT fader at nominal level) 74 dB CH INPUT (CH124) to STEREO OUT/OMNI (BUS) OUT Maximum Voltage Gain 74 dB CH INPUT (CH124) to OMNI (AUX) OUT (via pre input fader) 74 dB CH INPUT (CH124) to CONTROL ROOM MONITOR OUT (via STEREO bus) Crosstalk (@ 1 kHz) 80 dB adjacent input channels (CH124) 80 dB input to output Phantom switch Pad switch Gain control Peak indicator AD Input (1 16: A/B) Signal indicator Insert Insert switch AD converter Gain control Peak indicator AD Input (17 24) Signal indicator AD converter Analog Input (2TR IN ANALOG 1, 2) AD converter +48 V DC is supplied to A (XLR-3-31 type) input 0/26 dB attenuation 44 dB (60 to 16), detented LED (red) turns on when post HA level reaches 3 dB below clipping LED (green) turns on when post HA level reaches 20 dB below nominal I/O (pre AD converter) on/off 24-bit linear, 128-times oversampling (fs=48 kHz) 44 dB (34 to +10), detented LED (red) turns on when post HA level reaches 3 dB below clipping LED (green) turns on when post HA level reaches 20 dB below nominal 24-bit linear, 128-times oversampling (fs=48 kHz) 24-bit linear, 128-times oversampling (fs=48 kHz)
Rs=150 Input Gain=Max. Input Pad =0 dB
Input Gain=Min.
4
02R96
Option Input (SLOT 14) Digital Input (2TR IN DIGITAL 13)
Available cards SRC Input patch Phase Gate-type *3
Optional digital interface cards (MY8, MY4 series) On/off (1:3 and 3:1 maximum input to output sample rate ratio) -- Normal/reverse On/off Key in: 12 ch Group (112, 1324, 2536, 3748, 4956)/AUX18 On/off Key in: self /Stereo Link Pre EQ/pre fader/post fader 96.0 to +12.0 dB (0.1 dB step) 4-band PEQ *5 On/off 043400 samples -- 100 mm motorized (INPUT/AUX18) On/off AUX18; pre fader/post fader On/off Pre fader/after pan 127 positions (Left= 163, Center, Right= 163) 127 × 127 positions , 96 dB to +10 dB (256 step) STEREO, BUS18, DIRECT OUT Pre EQ/pre fader/post fader Displayed on LCD Peak hold on/off Analog rotary potentiometer 24-bit linear, 128-times oversampling Built-in microphone/AD IN 116 -- 0 to 96 dB (1 dB step) -- Sine 100 Hz, sine 1 kHz, sine 10 kHz, pink noise, burst noise BUS18, AUX18, STEREO L, R 24-bit linear, 128-times oversampling SURROUND MONITOR, STEREO, BUS18, AUX18, DIRECT OUT 156, INSERT OUT (CH156, BUS18, AUX18, STEREO) 24-bit linear, 128-times oversampling STEREO, 2TR IN DIGITAL 1, 2TR IN DIGITAL 2, 2TR IN DIGITAL 3, 2TR IN ANALOG 1, 2TR IN ANALOG 2, ASSIGN 1, 2 (BUS 18/AUX 18) On/off On/off 24-bit linear, 128-times oversampling Analog rotary potentiometer Analog rotary potentiometer CONTROL ROOM, STEREO, AUX 7, AUX 8, TALKBACK 24-bit linear, 128-times oversampling Analog rotary potentiometer
Comp-type*4 Attenuator EQ Delay On/off Input Channel CH156 Fader Aux send Solo Pan Surround pan LFE level Routing Direct out Metering Level control AD converter TALKBACK Talkback select On/off Level On/off OSCILLATOR Waveform Routing STEREO OUT OMNI OUT 18 DA converter Monitor select Mono CONTROL ROOM MONITOR OUT Dimmer DA converter Level control Phones level Monitor select STUDIO MONITOR OUT DA converter Level control DA converter Output patch
5
02R96
Dither 2TR OUT DIGITAL 13 Output patch Available card Option Output (SLOT 14) Output patch Dither Comp-type*4 Attenuator EQ STEREO On/off Fader Balance Delay Metering Comp-type*4 Attenuator EQ On/off BUS18 Fader Delay Bus to stereo
On/off Word length 16, 20, 24-bit STEREO, BUS18, AUX 18, DIRECT OUT 156, INSERT OUT, CONTROL ROOM Optional digital interface card (MY8, MY4 series) SURROUND MONITOR, STEREO, BUS18, AUX18, DIRECT OUT 156, INSERT OUT (CH156, BUS18, AUX18, STEREO) On/off Word length 16/20/24-bit On/off Pre EQ/pre fader/post fader 96.0 to +12.0 dB (0.1 dB step) 4-band PEQ *5 On/off -- 100 mm motorized 127 positions (Left=163, Center, Right=163) 043400 samples Displayed on LCD Peak hold on/off On/off Pre EQ/pre fader/post fader 96.0 to +12.0 dB (0.1 dB step) 4-band PEQ *5 On/off -- 100 mm motorized 043400 samples Level (, 130 dB to 0 dB) On/off Pan: 127 positions (Left=163, Center, Right=163) Displayed on LCD Peak hold on/off On/off Pre EQ/pre fader/post fader 96.0 to +12.0 dB (0.1 dB step) 4-band PEQ *5 On/off -- 100 mm motorized 043400 samples Displayed on LCD Peak hold on/off
Metering Comp-type*4 Attenuator EQ AUX18 On/off Fader Delay Metering
6
02R96
Mute Solo Source Monitor to C-R SURROUND MONITOR Oscillator Monitor matrix Bass management Monitor alignment Bypass INTERNAL EFFECTS (EFFECT 14) In/out Effect-in from Effect-out to Japan Power Requirements U.S.A./Canada Other Dimensions Net weight Operating free-air temperature range Storage temperature range Supplied Accessories (H x D x W)
On/off On/off BUS18, SLOT 14 On/off Pink noise/5002 kHz/1 kHz/50 Hz 5.1 5.1, 5.1 3-1, 5.1 ST, 3.1 3.1, 3.1 ST 5 presets ATT (12.0 dB to 12 dB 0.1 dB step), Delay (030.0 msec 0.02 msec step) On/off 8-in, 8-out (EFFECT1): depends on effects type 2-in, 2-out (EFFECT24): depends on effects type AUX18/INSERT OUT/effect-out Input patch/effect-in 100 V, 50/60 Hz 190 W 120 V, 60 Hz 200 W 220240 V, 50/60 Hz 200 W 239 x 697 x 667 mm (9.4" x 27.4" x 26.3") 34 kg (75 lbs) 1035°C (5095°F) 20 to 60°C (4 to 140°F) AC Cable CD-ROM (Studio Manager) Digital interface card (MY8, MY4 series) PEAK METER BRIDGE: MB02R96 SIDE PANEL: SP02R96
Options
*1. Total harmonic distortion is measured with a 6 dB/octave filter @ 80 kHz. *2. Hum & Noise are measured with a 6 dB/octave filter @ 12.7 kHz; equivalent to a 20 kHz filter with infinite dB/octave attenuation. *3. See"Gate Parameters" on page 8. *4. See"Comp Parameters" on page 8. *5. See"EQ Parameters" on page 7.
EQ Parameters
LOW/HPF 0.110.0 (41 points) low shelving HPF ±18 dB (0.1 dB step) HPF: on/off L-MID 0.110.0 (41 points) 21.2 Hz20 kHz (1/12 oct step) ±18 dB (0.1 dB step) ±18 dB (0.1 dB step) LPF: on/off H-MID HIGH /LPF 0.110.0 (41 points) high shelving LPF
Q
F G
7
02R96
Gate Parameters
Threshold Range Attack 54 dB to 0 dB (0.1 dB step) 70 dB to 0 dB (1 dB step) 0 ms120 ms (1 ms step) 0.02 ms1.96 s (216 points) @ 48 kHz Gate Hold 0.02 ms2.13 s (216 points) @ 44.1 kHz 0.01 ms981 ms (216 points) @ 96 kHz 0.01 ms1.06 s (216 points) @ 88.2 kHz 5 ms42.3 s (160 points) @ 48 kHz Decay 6 ms46.0 s (160 points) @ 44.1 kHz 3 ms21.1 s (160 points) @ 96 kHz 3 ms23.0 s (160 points) @ 88.2 kHz Threshold Range Attack 54 dB to 0 dB (0.1 dB step) 70 dB to 0 dB (1 dB step) 0 ms120 ms (1 ms step) 0.02 ms1.96 s (216 points) @ 48 kHz Ducking Hold 0.02 ms2.13 s (216 points) @ 44.1 kHz 0.01 ms981 ms (216 points) @ 96 kHz 0.01 ms1.06 s (216 points) @ 88.2 kHz 5 ms42.3 s (160 points) @ 48 kHz Decay 6 ms46.0 s (160 points) @ 44.1 kHz 3 ms21.1 s (160 points) @ 96 kHz 3 ms23.0 s (160 points) @ 88.2 kHz
Comp Parameters
Threshold Ratio (x :1) Out gain Knee Compressor Attack 54 dB to 0 dB (0.1 dB step) x=1, 1.1, 1.3, 1.5, 1.7, 2, 2.5, 3, 3.5, 4, 5, 6, 8, 10, 20, (16 points) 0 dB to +18 dB (0.1 dB step) Hard, 1, 2, 3, 4, 5 (6 step) 0 ms120 ms (1 ms step) 5 ms42.3 s (160 points) @ 48 kHz Release 6 ms46.0 s (160 points) @ 44.1 kHz 3 ms21.1 s (160 points) @ 96 kHz 3 ms23.0 s (160 points) @ 88.2 kHz Threshold Ratio (x :1) Out gain Knee Expander Attack 54 dB to 0 dB (0.1 dB step) x=1, 1.1, 1.3, 1.5, 1.7, 2, 2.5, 3, 3.5, 4, 5, 6, 8, 10, 20, (16 points) 0 dB to +18 dB (0.1 dB step) Hard, 1, 2, 3, 4, 5 (6 points) 0 ms120 ms (1 ms step) 5 ms42.3 s (160 points) @ 48 kHz Release 6 ms46.0 s (160 points) @ 44.1 kHz 3 ms21.1 s (160 points) @ 96 kHz 3 ms23.0 s (160 points) @ 88.2 kHz
8
02R96
Threshold Ratio (x :1) Out gain Width Compander H Attack
54 dB to 0 dB (0.1 dB step) x=1, 1.1, 1.3, 1.5, 1.7, 2, 2.5, 3, 3.5, 4, 5, 6, 8, 10, 20 (15 points) 18 dB to 0 dB (0.1 dB step) 1 dB90 dB (1 dB step) 0 ms120 ms (1 ms step) 5 ms42.3 s (160 points) @ 48 kHz 6 ms46.0 s (160 points) @ 44.1 kHz 3 ms21.1 s (160 points) @ 96 kHz 3 ms23.0 s (160 points) @ 88.2 kHz
Release
Threshold Ratio (x :1) Out gain Width Compander S Attack
54 dB to 0 dB (0.1 dB step) x=1, 1.1, 1.3, 1.5, 1.7, 2, 2.5, 3, 3.5, 4, 5, 6, 8, 10, 20 (15 points) 18 dB to 0 dB (0.1 dB step) 1 dB90 dB (1 dB step) 0 ms120 ms (1 ms step) 5 ms42.3 s (160 points) @ 48 kHz 6 ms46.0 s (160 points) @ 44.1 kHz 3 ms21.1 s (160 points) @ 96 kHz 3 ms23.0 s (160 points) @ 88.2 kHz
Release
Controls Analog Section
+48 V switch INPUT 116 PAD switch GAIN control INSERT switch INPUT 1724 TALKBACK STUDIO MONITOR OUT CONTROL ROOM MONITOR OUT PHONES GAIN control TALKBACK LEVEL control STUDIO LEVEL control CONTROL ROOM LEVEL control PHONES LEVEL control ON/OFF 0/26 dB 16 to 60 dB ON/OFF +10 to 34 dB
Digital Section
DISPLAY button AUX SELECT FADER MODE Section FADER MODE ENCODER MODE DISPLAY ACCESS buttons EFFECTS/PLUG-INS AUX 1, AUX 2, AUX 3, AUX 4, AUX 5, AUX 6, AUX 7, AUX 8 buttons (w/LED) FADER, AUX button (w/LED) DISPLAY button PAN, AUX, ASSIGN 1, ASSIGN 2 buttons (w/LED) AUTOMIX, DIO, SETUP, UTILITY, MIDI, REMOTE, METER, VIEW, PAIR, GROUP, INPUT PATCH, OUTPUT PATCH DISPLAY access, DISPLAY CONTROL Section , INTERNAL EFFECTS, PLUG-INS, CHANNEL INSERTS, 1, 2, 3, 4 Parameter control: 1, 2, 3, 4 Others , F1, F2, F3, F4, LCD contrast control buttons
9
02R96
DISPLAY button ROUTING DISPLAY ACCESS DYNAMICS 1, 2, 3, 4, 5, 6, 7, 8, STEREO, DIRECT, FOLLOW PAN buttons (w/LED) PHASE/INSERT, DELAY buttons DISPLAY, GATE /COMP buttons GATE ON, COMP ON buttons (w/LED) Parameter control x 5 SELECTED CHANNEL Section PAN/SURROUND DISPLAY button L, R, LINK, GRAB, EFFECT buttons (w/LED) Pan control Joystick (Sound image position control) DISPLAY button EQ ON button (w/LED) EQUALIZER GAIN controls: LOW, LOW-MID, HIGH-MID, HIGH FREQUENCY/Q controls: LOW, LOW-MID, HIGH-MID, HIGH controls (w/SW) MONITOR STUDIO SOLO MONITOR Section CONTROL ROOM SURROUND Others SCENE MEMORY SCENE MEMORY and USER DEFINED KEYS section USER DEFINED KEYS DISPLAY button CONTROL ROOM, STEREO, AUX 7, AUX 8 buttons (w/LED) CLEAR button 2TR D1, 2TR D2, 2TR D3, 2TR A1, 2TR A2, STEREO, ASSIGN 1, ASSIGN 2 buttons (w/LED) BUS, SLOT buttons (w/LED) SURROUND MONITOR LEVEL control TALKBACK, DIMMER buttons (w/LED) CONTROL ROOM LEVEL control DISPLAY button , , STORE, RECALL buttons DISPLAY button 1, 2, 3, 4, 5, 6, 7, 8, 9, 10, 11, 12, 13, 14, 15, 16 buttons (w/LED) DISPLAY button LOCATE MEMORY: 1, 2, 3, 4, 5, 6, 7, 8, SET buttons (w/LED) TRANSPORT CONTROL Encoders CHANNEL STRIP Section Buttons Faders (w/ touch sense) LAYER MASTER Section STEREO Buttons DATA ENTRY Section Encoder REW, FF, STOP, PLAY, REC, SHUTTLE, SCRUB (w/LED) x 24 (124) AUTO x 24 (124), SEL x 24 (124), SOLO x 24 (124), ON x 24 (124) x 24 (124) 124, 2548, MASTER, REMOTE buttons (w/LED) AUTO, SEL, ON buttons (w/LED) Fader (w/touch sense) x 1 INC, DEC, , , , , ENTER buttons
LOCATOR MACHINE CONTROL Section
Parameter wheel
10
02R96
Indicators Analog Section
PEAK LED SIGNAL LED x24 x24 INPUT 124 INPUT 124
Digital Section
DISPLAY CONTROL Section DISPLAY DYNAMICS PAN/SURROUND SELECTED CHANNEL Section EQUALIZER MONITOR Section SCENE MEMORY section SOLO Scene memory number 320 × 240 dot graphic LCD (w/contrast control potentiometer) GATE, COMP LEDs x2 Pan position LEDs x10 FREQUENCY, Q LEDs 2 × 4 dB, Hz, kHz 3 × 4 3-digit numeric LEDs x4 (parameter value) LED x1 2-digit numeric LED x1
Libraries
Effect library (EFFECT 14) Compressor library Gate library EQ library Channel library Surround Monitor library Input patch library Output patch library Bus to Stereo library Presets User memories Presets User memories Presets User memories Presets User memories Presets User memories Presets User memories Presets User memories Presets User memories Presets User memories 52 (EFFECT 24: 44) 76 36 92 4 124 40 160 2 127 1 32 1 32 1 32 1 32
11
02R96
Analog Input Spec
Input PAD GAIN Actual Load Impedance Input level For Use With *1 Nominal Nominal Sensitivity 70 dB (0.245 mV) 26 dB (38.8 mV) 0 dB (775 mV) 44 dB (4.89 mV) 0 dB (775 mV) 6 dB (388 mV) +4 dB (1.23 V) 10 dBV (0.316 V) 60 dB (0.775 mV) 16 dB (0.123 V) +10 dB (2.45 V) 34 dB (15.5 mV) +10 dB (2.45 V) +4 dB (1.23 V) +4 dB (1.23 V) 10 dBV (0.316 V) Max. before clip 46 dB (3.88 mV) 2 dB (616 mV) +24 dB (12.28 V) 20 dB (77.5 mV) +24 dB (12.28 V) +18 dB (6.16 V) +18 dB (6.16 V) +4 dBV (1.58 V) Phone jack (TRS) (Balanced) *3 Phone jack (TRS) *4 Phone jack (TRS) (Balanced) *3 Phono (Unbalanced) Connector A: XLR-3-31 type (Balanced) *2 B: Phone jack (TRS) (Balanced) *3
0 INPUT A/B 116 26
60 dB 16 dB 34 dB +10 dB -- -- -- 3k
50600 Mics & 600 Lines
INPUT 1724
--
4K
600 Lines 600 Lines 600 Lines 600 Lines
INSERT IN 116 2TR IN ANALOG 1 [L, R] 2TR IN ANALOG 2 [L, R]
10K 10K 10K
*1. Sensitivity is the lowest level that will produce an output of +4 dB (1.23 V) or the nominal output level when the unit is set to maximum gain. (All faders and level controls are maximum position.) *2. XLR-3-31 type connectors are balanced (1=GND, 2=HOT, 3=COLD). *3. Phone jacks are balanced (Tip=HOT, Ring=COLD, Sleeve=GND). *4. Phone jacks are wired: Tip=OUT, Ring=IN, Sleeve=GND In these specifications, when dB represents a specific voltage, 0 dB is referenced to 0.775 Vrms. For 2TR IN ANALOG 2 levels, 0 dBV is referenced to 1.00 Vrms. All input AD converters (except INSERT I/O 116) are 24-bit linear, 128-times oversampling. +48 V DC (phantom power) is supplied to CH INPUT (116) XLR type connectors via individual switches.
Analog Output Spec
Output Actual Source Impedance 600 STEREO OUT [L, R] 150 STUDIO MONITOR OUT [L, R] C-R MONITOR OUT [L, R] 150 150 600 Lines 10k Lines 10k Lines -- -- -- +18 dB (default) +4 dB INSERT OUT 116 PHONES 600 100 10k Lines 8 Phones 40 Phones -- -- -- For Use With Nominal 10k Lines Output level GAIN SW *1 Nominal 10 dBV (0.316 V) +4 dB (1.23 V) +4 dB (1.23 V) +4 dB (1.23 V) +4 dB (1.23 V) 10 dB (0.245 V) +4 dB (1.23 V) 4 mW 12 mW Max. before clip +4 dBV (1.58 V) +18 dB (6.16 V) +18 dB (6.16 V) +18 dB (6.16 V) +18 dB (6.16 V) +4 dB (1.23 V) +18 dB (6.16 V) 25 mW 75 mW Connector
--
Phono (Unbalanced) XLR-3-32 type (Balanced) *2 Phone Jack (TRS) (Balanced) *3 Phone Jack (TRS) (Balanced) *3 Phone Jack (TRS) (Balanced) *3 Phone Jack (TRS) *4 Stereo Phone Jack (TRS) (Unbalanced) *5
OMNI OUT 18
150
10k Lines
*1. The maximum output level of each OMNI OUT can be set internally. *2. XLR-3-32 type connectors are balanced (1=GND, 2=HOT, 3=COLD). *3. Phone jacks are balanced (Tip=HOT, Ring=COLD, Sleeve=GND). *4. Phone jacks are wired: Tip=OUT, Ring=IN, Sleeve=GND *5. PHONES stereo phone jack is unbalanced (Tip=LEFT, Ring=RIGHT, Sleeve=GND). STEREO OUT [L, R], 0 dBV is referenced to 1.00 Vrms. In these specifications, when dB represents a specific voltage, 0 dB is referenced to 0.775 Vrms. All output DA converters (except INSERT OUT 116) are 24-bit, 128-times oversampling.
12
02R96
Digital Input Spec
Input 1 2TR IN DIGITAL 2 3 CASCADE IN Format AES/EBU IEC-60958 IEC-60958 -- Data length 24-bit 24-bit 24-bit -- Level RS422 Connector XLR-3-31 type (Balanced) *1
0.5 Vpp/75 Phono 0.5 Vpp/75 Phono RS422 D-SUB Half Pitch Connector 68P (Female)
*1. XLR-3-31 type connectors are balanced (1=GND, 2=HOT, 3=COLD).
Digital Output Spec
Output 1 2TR OUT DIGITAL 2 3 CASCADE OUT Format AES/EBU Professional use IEC-60958 *4 Consumer use IEC-60958 *4 Consumer use --
*1
Data length 24-bit *2 24-bit *2 24-bit *2 --
Level RS422
Connector XLR-3-32 type (Balanced) *3
0.5V pp/75 Phono 0.5V pp/75 Phono RS422 D-SUB Half Pitch Connector 68P (Female)
*1. Channel status of 2TR OUT DIGITAL 1 Type: 2 audio channels Emphasis: NO Sampling rate: depends on the internal configuration *2. Dither: word length 16/20/24 bit *3. XLR-3-32 type connectors are balanced (1=GND, 2=HOT, 3=COLD). *4. Channel status of 2TR OUT DIGITAL 2, 3 Type: 2 audio channels Category code: 2 channel PCM encoder/decoder Copy prohibit: NO Emphasis: NO Clock accuracy: Level II (1000 ppm) Sampling rate: depends on the internal configuration
13
02R96
I/O Slot Spec (1-4)
Each I/O SLOT accepts a digital interface card. Only SLOT #1 has a serial interface.
Card Name MY8-AT MY8-TD MY8-AE MY4-AD MY8-AD MY4-DA MY8-AD24 MY8-AD96 MY8-DA96 MY8-AE96S MY8-AE96 Function ADAT TASCAM AES/EBU ANALOG IN ANALOG IN ANALOG OUT ANALOG IN ANALOG IN ANALOG OUT AES/EBU AES/EBU Accept YES YES YES YES YES YES YES YES YES YES YES Input 8 IN 8 IN 8 IN 4 IN 8 IN -- 8 IN 8 IN -- 8 IN 8 IN patch) *1 8 OUT (depends on output patch) *1 8 OUT (depends on output patch) *1 patch) *1 -- -- 8 OUT (depends on output Output 8 OUT (depends on output patch) *1 8 OUT (depends on output patch) *1 8 OUT (depends on output patch) *1 -- -- 4 OUT (depends on output Number of available cards 4 4 4 4 4 4 4 4 4 2 4
*1. See the Digital I/O chapter. Details depend on each interface card.
Control I/O Spec
I/O Port Serial TO HOST USB IN MIDI OUT THRU MTC TIME CODE IN SMPTE IN WORD CLOCK OUT CONTROL METER Format -- USB 1.1 MIDI MIDI MIDI MIDI SMPTE -- -- -- -- Level RS422 0 V3.3 V -- -- -- -- Connector in Console Mini DIN Connector 8P B type USB connector DIN Connector 5P DIN Connector 5P DIN Connector 5P DIN Connector 5P
Nominal 10 dB/10k XLR-3-31 type (Balanced) *1 TTL/75 (ON/OFF) *2 BNC Connector TTL/75 -- RS422 BNC Connector D-SUB Connector 25P (Female) D-SUB Connector 15P (Female)
*1. XLR-3-31 type connectors are balanced (1=GND, 2=HOT, 3=COLD). *2. This switch is on the rear panel.
14
02R96
Connector Pin Assignments CASCADE IN
Pin 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 Signal GND INPUT 1-2(+) INPUT 3-4(+) INPUT 5-6(+) INPUT 7-8(+) INPUT 9-10(+) INPUT 11-12(+) INPUT 13-14(+) INPUT 15-16(+) DTR IN(+) RTS OUT(+) GND WORD CLOCK IN(+) WORD CLOCK OUT(+) CONTROL IN(+) CONTROL OUT(+) GND GND INPUT 17-18(+) INPUT 19-20(+) INPUT 21-22(+) INPUT 23-24(+) RESERVED RESERVED RESERVED RESERVED ID0 IN ID2 IN ID4 IN ID0 OUT ID2 OUT ID4 OUT Pin 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 Signal GND INPUT 1-2() INPUT 3-4() INPUT 5-6() INPUT 7-8() INPUT 9-10() INPUT 11-12() INPUT 13-14() INPUT 15-16() DTR IN() RTS OUT() GND WORD CLOCK IN() WORD CLOCK OUT() CONTROL IN() CONTROL OUT() ID6 IN ID6 OUT INPUT 17-18() INPUT 19-20() INPUT 21-22() INPUT 23-24() RESERVED RESERVED RESERVED RESERVED ID1 IN ID3 IN ID5 IN ID1 OUT ID3 OUT ID5 OUT Pin 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32
CASCADE OUT
Signal GND OUTPUT 1-2(+) OUTPUT 3-4(+) OUTPUT 5-6(+) OUTPUT 7-8(+) OUTPUT 9-10(+) OUTPUT 11-12(+) OUTPUT 13-14(+) OUTPUT 15-16(+) DTR OUT(+) RTS IN(+) GND WORD CLOCK OUT(+) WORD CLOCK IN(+) CONTROL OUT(+) CONTROL IN(+) GND GND OUTPUT 17-18(+) OUTPUT 19-20(+) OUTPUT 21-22(+) OUTPUT 23-24(+) RESERVED RESERVED RESERVED RESERVED ID0 OUT ID2 OUT ID4 OUT ID0 IN ID2 IN ID4 IN Pin 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 Signal GND OUTPUT 1-2() OUTPUT 3-4() OUTPUT 5-6() OUTPUT 7-8() OUTPUT 9-10() OUTPUT 11-12() OUTPUT 13-14() OUTPUT 15-16() DTR OUT() RTS IN() GND WORD CLOCK OUT() WORD CLOCK IN() CONTROL OUT() CONTROL IN() ID6 OUT ID6 IN OUTPUT 17-18() OUTPUT 19-20() OUTPUT 21-22() OUTPUT 23-24() RESERVED RESERVED RESERVED RESERVED ID1 OUT ID3 OUT ID5 OUT ID1 IN ID3 IN ID5 IN
33 MSB IN 34 FG
67 2CH/LINE IN 68 FG
33 MSB OUT 34 FG
67 2CH/LINE OUT 68 FG
CONTROL Port
Pin 1 2 3 4 5 6 7 8 9 10 11 12 13 Signal GPO0 GPO2 GPO4 GPO6 GND GND GND GND +5V GPI1 N.C. SMODE *1 SPARE
*1
Pin 14 15 16 17 18 19 20 21 22 23 24 25
Signal GPO1 GPO3 GPO5 GPO7 GND GND GND +5V GPI0 N.C. SOLO *1 MAS/SLV *1
MB02R96
Dimensions (W X H X D): 667 X 124 X 95 mm Weight: 2.8 kg
*1. For 02R SOLO control.
15
16
02R96
DIMENSIONS
239 mm
Side view
Top view
+ 48V
ON OFF
+ 48V
ON OFF
+ 48V
ON OFF
+ 48V
ON OFF
+ 48V
ON OFF
+ 48V
ON OFF
+ 48V
ON OFF
+ 48V
ON OFF
+ 48V
ON OFF
+ 48V
ON OFF
+ 48V
ON OFF
+ 48V
ON OFF
+ 48V
ON OFF
+ 48V
ON OFF
+ 48V
ON OFF
+ 48V
ON OFF
17
19
21
23
PAD
26dB 26dB 26dB 26dB 26dB 26dB 26dB 26dB 26dB 26dB 26dB 26dB 26dB 26dB 26dB 26dB
+10
GAIN
34
+10
GAIN
34
+10
GAIN
34
+10
GAIN
34
0
10
TALKBACK LEVEL
18
20
22
24
-16
GAIN PEAK SIGNAL
-60
-16
GAIN PEAK SIGNAL
-60
-16
GAIN PEAK SIGNAL
-60
-16
GAIN PEAK SIGNAL
-60
-16
GAIN PEAK SIGNAL
-60
-16
GAIN PEAK SIGNAL
-60
-16
GAIN PEAK SIGNAL
-60
-16
GAIN PEAK SIGNAL
-60
-16
GAIN PEAK SIGNAL
-60
-16
GAIN PEAK SIGNAL
-60
-16
GAIN PEAK SIGNAL
-60
-16
GAIN PEAK SIGNAL
-60
-16
GAIN PEAK SIGNAL
-60
-16
GAIN PEAK SIGNAL
-60
-16
GAIN PEAK SIGNAL
-60
-16
GAIN PEAK SIGNAL
-60
+10
GAIN PEAK
34
+10
GAIN PEAK
34
+10
GAIN PEAK
34
+10
GAIN PEAK
34
PHONES
SIGNAL SIGNAL SIGNAL SIGNAL
1
OFF ON
2
OFF ON
3
OFF ON
4
OFF ON
5
OFF ON
6
OFF ON
7
OFF ON
8
OFF ON
9
OFF ON
10
OFF ON
11
OFF ON
12
OFF ON
13
OFF ON
14
OFF ON
15
OFF ON
16
OFF ON
17 18
19 20
21 22
23 24
0 10 0 10
INSERT
INSERT
INSERT
INSERT
INSERT
INSERT
INSERT
INSERT
INSERT
INSERT
INSERT
INSERT
INSERT
INSERT
INSERT
INSERT
STUDIO LEVEL
DIGITAL MIXING CONSOLE
PHONES LEVEL
ROUTING
DISPLAY
SELECTED CHANNEL
DISPLAY ACCESS
MONITOR
DISPLAY
1
2
STUDIO
3
4
DISPLAY ACCESS
5
AUTOMIX DIO SETUP UTILITY
PHASE / INSERT
DELAY
CONTROL ROOM
STEREO
6
DISPLAY
PAN / SURROUND
AUX7
AUX8
SOLO
7 8
CLEAR MIDI REMOTE METER VIEW FOLLOW PAN STEREO DIRECT L R
CONTROL ROOM
L
ODD
R
EVEN
LINK
GRAB
EFFECT 2TR D1 2TR A1
DYNAMICS
PAIR GROUP INPUT PATCH OUTPUT PATCH DISPLAY GATE ON COMP ON GATE / COMP GATE COMP
AUX 1 AUX 2 AUX 3 AUX 4
AUX SELECT
DISPLAY
2TR D2 THRESHOLD THRESHOLD RANGE RATIO ATTACK ATTACK DECAY RELEASE HOLD GAIN 2TR D3
2TR A2
EQUALIZER LOW
DISPLAY
STEREO
LOW MID
FREQUENCY
HIGH MID
FREQUENCY FREQUENCY GAIN
dB Hz kHz
HIGH
ASSIGN2 ASSIGN1 SURROUND GAIN
AUX 5
AUX 6
AUX 7
AUX 8
FREQUENCY
ENCODER MODE
DISPLAY PAN AUX
ASSIGN 1 ASSIGN 2
Q
GAIN
dB Hz
Q
GAIN
dB Hz kHz
Q
Q
697 mm
dB Hz kHz
BUS
SLOT
FADER MODE
EQ ON
kHz
USER DEFINED KEYS
FADER AUX DISPLAY 1 DISPLAY INTERNAL EFFECTS PLUG INS CHANNEL INSERTS 2 3 4 5 6 7 8 DISPLAY
SCENE MEMORY
0 10 SURROUND MONITOR LEVEL
EFFECTS / PLUG INS
0 10 CONTROL ROOM LEVEL STORE 9 10 11 12 13 14 15 16 DIMMER TALKBACK RECALL
1
2
3
4
LAYER
DISPLAY 1 24 REMOTE
MACHINE CONTROL LOCATE MEMORY
1
2
3
4
AUTO
AUTO
AUTO
AUTO
AUTO
AUTO
AUTO
AUTO
AUTO
AUTO
AUTO
AUTO
AUTO
AUTO
AUTO
AUTO
AUTO
AUTO
AUTO
AUTO
AUTO
AUTO
AUTO
AUTO
25 48
MASTER
SET
5
6
7
8
STEREO
SEL SEL SEL SEL SEL SEL SEL SEL SEL SEL SEL SEL SEL SEL SEL SEL SEL SEL SEL SEL SEL SEL SEL SEL AUTO SOLO SOLO SOLO SOLO SOLO SOLO SOLO SOLO SOLO SOLO SOLO SOLO SOLO SOLO SOLO SOLO SOLO SOLO SOLO SOLO SOLO SOLO SOLO SOLO SEL ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON STOP PLAY REC
REW
FF
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
ON
DEC
10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 0
INC
5 0
5 0
5 0
5 0
5 0
5 0
5 0
5 0
5 0
5 0
5 0
5 0
5 0
5 0
5 0
5 0
5 0
5 0
5 0
5 0
5 0
5 0
5 0
5 0
5
SHUTTLE
10
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
15
SCRUB
10
10
10
10
10
10
10
10
10
10
10
10
10
10
10
10
10
10
10
10
10
10
10
10
20
15
15
15
15
15
15
15
15
15
15
15
15
15
15
15
15
15
15
15
15
15
15
15
15
30
20
20
20
20
20
20
20
20
20
20
20
20
20
20
20
20
20
20
20
20
20
20
20
20
40
30 40 50
30 40 50
30 40 50
30 40 50
30 40 50
30 40 50
30 40 50
30 40 50
30 40 50
30 40 50
30 40 50
30 40 50
30 40 50
30 40 50
30 40 50
30 40 50
30 40 50
30 40 50
30 40 50
30 40 50
30 40 50
30 40 50
30 40 50
30 40 50
50 60 70
ENTER
1 25 49
2 26 50
3 27 51
4 28 52
5 29 53
6 30 54
7 31 55
8 32 56
9 33
AUX 1
10 34
AUX 2
11 35
AUX 3
12 36
AUX 4
13 37
AUX 5
14 38
AUX 6
15 39
AUX 7
16 40
AUX 8
17 41
BUS 1
18 42
BUS 2
19 43
BUS 3
20 44
BUS 4
21 45
BUS 5
22 46
BUS 6
23 47
BUS 7
24 48
BUS 8
STEREO
667 mm
02R96 Control Panel
PANEL LAYOUT
Display Section (p. 20)
SELECTED CHANNEL Section (p. 21)
+ 48V
+ 48V
ON OFF ON OFF
+ 48V
ON OFF
+ 48V
ON OFF
+ 48V
ON OFF
+ 48V
ON OFF
+ 48V
ON OFF
+ 48V
ON OFF
+ 48V
ON OFF
+ 48V
ON OFF
+ 48V
ON OFF
+ 48V
ON OFF
+ 48V
ON OFF
+ 48V
ON OFF
+ 48V
ON OFF
+ 48V
ON OFF
AD Input Section (p. 18)
PAD
26dB
17
19
21
23
+10
26dB
26dB
26dB
26dB
26dB
26dB
26dB
26dB
26dB
26dB
26dB
26dB
26dB
26dB
26dB
GAIN
34
+10
GAIN
34
+10
GAIN
34
+10
GAIN
34
0
10
TALKBACK LEVEL
18
20
22
24
Monitor , Phones & T alkback Section (p. 25)
-16
GAIN PEAK SIGNAL
-60
-16
GAIN PEAK SIGNAL
-60
-16
GAIN PEAK SIGNAL
-60
-16
GAIN PEAK SIGNAL
-60
-16
GAIN PEAK SIGNAL
-60
-16
GAIN PEAK SIGNAL
-60
-16
GAIN PEAK SIGNAL
-60
-16
GAIN PEAK SIGNAL
-60
-16
GAIN PEAK SIGNAL
-60
-16
GAIN PEAK SIGNAL
-60
-16
GAIN PEAK SIGNAL
-60
-16
GAIN PEAK SIGNAL
-60
-16
GAIN PEAK SIGNAL
-60
-16
GAIN PEAK SIGNAL
-60
-16
GAIN PEAK SIGNAL
-60
-16
GAIN PEAK SIGNAL
-60
+10
GAIN PEAK
34
+10
GAIN PEAK
34
+10
GAIN PEAK
34
+10
GAIN PEAK
34
PHONES
SIGNAL SIGNAL SIGNAL SIGNAL
1
OFF ON
2
OFF ON
3
OFF ON
4
OFF ON
5
OFF ON
6
OFF ON
7
OFF ON
8
OFF ON
9
OFF ON
10
OFF ON
11
OFF ON
12
OFF ON
13
OFF ON
14
OFF ON
15
OFF ON
16
OFF ON
17 18
19 20
21 22
23 24
0 10 0 10
INSERT
INSERT
INSERT
INSERT
INSERT
INSERT
INSERT
INSERT
INSERT
INSERT
INSERT
INSERT
INSERT
INSERT
INSERT
INSERT
STUDIO LEVEL
DIGITAL MIXING CONSOLE
PHONES LEVEL
ROUTING
DISPLAY
SELECTED CHANNEL
DISPLAY ACCESS
MONITOR
DISPLAY
1
2
STUDIO
3
4
DISPLAY ACCESS (p. 19) AUX SELECT (p. 19)
DISPLAY
DISPLAY ACCESS
5
AUTOMIX DIO SETUP UTILITY
PHASE / INSERT
DELAY
CONTROL ROOM
STEREO
6
DISPLAY
PAN / SURROUND
AUX7
AUX8
SOLO
7 8
CLEAR MIDI REMOTE METER VIEW FOLLOW PAN STEREO DIRECT L R
MONITOR Section (p.25)
CONTROL ROOM
L
ODD
R
EVEN
LINK
GRAB
EFFECT 2TR D1 2TR A1
DYNAMICS
PAIR GROUP INPUT PATCH OUTPUT PATCH DISPLAY GATE ON COMP ON GATE / COMP GATE COMP
AUX 1 AUX
AUX SELECT
2TR D2 THRESHOLD THRESHOLD RANGE RATIO ATTACK ATTACK DECAY RELEASE HOLD GAIN 2TR D3
2TR A2
2
AUX 3
AUX
4
DISPLAY
EQUALIZER LOW LOW MID
FREQUENCY GAIN
dB Hz
STEREO
HIGH MID
FREQUENCY FREQUENCY GAIN
dB Hz kHz
HIGH
ASSIGN2 ASSIGN1 SURROUND GAIN
dB Hz kHz
AUX
5
AUX 6
AUX 7
AUX
8
FREQUENCY Q Q GAIN
dB Hz kHz
ENCODER MODE (p. 19)
ENCODER MODE
DISPLAY PAN AUX
ASSIGN 1 ASSIGN
Q
Q
BUS
SLOT
2
EQ ON
FADER MODE
kHz
SCENE MEMORY (p. 23)
0 10 SURROUND MONITOR LEVEL 0 10 CONTROL ROOM LEVEL
USER DEFINED KEYS
FADER AUX DISPLAY 1 DISPLAY 2 3 4 5 6 7 8 DISPLAY
SCENE MEMORY
EFFECTS / PLUG INS
FADER MODE (p. 19)
INTERNAL EFFECTS
PLUG INS
CHANNEL INSERTS STORE 9 10 11 12 13 14 15 16 RECALL
1
2
3
4
DIMMER
TALKBACK
LAYER
DISPLAY 1 24 REMOTE
MACHINE CONTROL LOCATE MEMORY
1
2
3
4
EFFECTS/PLUG-INS (p. 20)
AUTO
AUTO
AUTO
AUTO
AUTO
AUTO
AUTO
AUTO
AUTO
AUTO
AUTO
AUTO
AUTO
AUTO
AUTO
AUTO
AUTO
AUTO
AUTO
AUTO
AUTO
AUTO
AUTO
AUTO
25 48
MASTER
SET
5
6
7
8
STEREO
SEL SEL SEL SEL SEL SEL SEL SEL SEL SEL SEL SEL SEL SEL SEL SEL SEL SEL SEL SEL SEL SEL SEL SEL AUTO SOLO SOLO SOLO SOLO SOLO SOLO SOLO SOLO SOLO SOLO SOLO SOLO SOLO SOLO SOLO SOLO SOLO SOLO SOLO SOLO SOLO SOLO SOLO SOLO SEL ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON ON STOP PLAY REC
MACHINE CONTROL (p. 24)
REW
FF
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
ON
DEC
10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 0
INC
5 0
5 0
5 0
5 0
5 0
5 0
5 0
5 0
5 0
5 0
5 0
5 0
5 0
5 0
5 0
5 0
5 0
5 0
5 0
5 0
5 0
5 0
5 0
5 0
5
SHUTTLE
10
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
15
SCRUB
Data Entry & Transport (p. 24)
10
10
10
10
10
10
10
10
10
10
10
10
10
10
10
10
10
10
10
10
10
10
10
10
20
15
15
15
15
15
15
15
15
15
15
15
15
15
15
15
15
15
15
15
15
15
15
15
15
30
20
20
20
20
20
20
20
20
20
20
20
20
20
20
20
20
20
20
20
20
20
20
20
20
40
30 40 50
30 40 50
30 40 50
30 40 50
30 40 50
30 40 50
30 40 50
30 40 50
30 40 50
30 40 50
30 40 50
30 40 50
30 40 50
30 40 50
30 40 50
30 40 50
30 40 50
30 40 50
30 40 50
30 40 50
30 40 50
30 40 50
30 40 50
30 40 50
50 60 70
ENTER
1 25 49
2 26 50
3 27 51
4 28 52
5 29 53
6 30 54
7 31 55
8 32 56
9 33
AUX 1
10 34
AUX 2
11 35
AUX 3
12 36
AUX 4
13 37
AUX 5
14 38
AUX 6
15 39
AUX 7
16 40
AUX 8
17 41
BUS 1
18 42
BUS 2
19 43
BUS 3
20 44
BUS 4
21 45
BUS 5
22 46
BUS 6
23 47
BUS 7
24 48
BUS 8
STEREO
Channel strips (p. 18)
USER DEFINED KEYS (p. 24) LAYER (p. 23)
STEREO (p. 23)
02R96
17
02R96
AD Input Section
+ 48V
q w e r t y
PAD
26dB
ON OFF
-16
GAIN PEAK SIGNAL
-60
1
OFF ON
INSERT
q [+48V ON/OFF] switches (AD 116) w [PAD] switches (AD 116) e [GAIN] controls r [PEAK] indicators t [SIGNAL] indicators y [INSERT ON/OFF] switches (AD 116)
17
e r t
+10
GAIN
34
18
+10
GAIN PEAK
34
SIGNAL
17 18
Channel strips
q w
AUTO
e
SEL
r
SOLO
t
ON
1
q Encoders w [AUTO] buttons e [SEL] buttons r [SOLO] buttons t [ON] buttons y Channel faders
10
y
5 0
5
10
15
20
30 40 50
1 25 49
18
02R96
AUX SELECT
q
DISPLAY
AUX SELECT
AUX 1
AUX
2
AUX
3
AUX
4
q AUX SELECT [DISPLAY] button w [AUX 1][AUX 8] buttons
AUX
5
AUX
6
AUX
7
AUX
8
w
ENCODER MODE
q
DISPLAY
ENCODER MODE
PAN
AUX
ASSIGN 1
ASSIGN
2
w e
r
q ENCODER MODE [DISPLAY] button w [PAN] button e [AUX] button r [ASSIGN 1] & [ASSIGN 2] buttons
FADER MODE
FADER MODE
FADER
AUX
q [FADER] button w [AUX] button
q w
DISPLAY ACCESS
q w e r
DISPLAY ACCESS
t y
AUTOMIX
DIO
SETUP
UTILITY
MIDI
REMOTE
METER
VIEW
u i
PAIR
GROUP
INPUT PATCH
OUTPUT PATCH
o !0 !1 !2
q [AUTOMIX] button w [DIO] button e [SETUP] button r [UTILITY] button t [REMOTE] button y [MIDI] button u [METER] button i [VIEW] button o [PAIR] button !0 [GROUP] button !1 [INPUT PATCH] button !2 [OUTPUT PATCH] button
19
02R96
EFFECTS/PLUG-INS
w e r q
DISPLAY INTERNAL EFFECTS PLUG INS CHANNEL INSERTS
EFFECTS / PLUG INS
1
2
3
4
t
y
u
q EFFECTS/PLUG-INS [DISPLAY] button w [INTERNAL EFFECTS] button e [PLUG-INS] button r [CHANNEL INSERTS] button t EFFECTS/PLUG-INS [1][4] buttons y Parameter Up/Down buttons u Parameter controls [1][4]
Display Section
q
w
e r
q Display w Contrast control e [F1][F4] buttons r Left Tab Scroll button t Right Tab Scroll button
t
20
02R96
SELECTED CHANNEL Section
ROUTING
DISPLAY
SELECTED CHANNEL
DISPLAY ACCESS
1
2
3
4
PHASE / INSERT
DELAY
5
6
DISPLAY
PAN / SURROUND
7
8
FOLLOW PAN
STEREO
DIRECT
L
R
L
ODD
R
EVEN
LINK
GRAB
EFFECT
DYNAMICS
DISPLAY GATE ON COMP ON GATE / COMP GATE COMP THRESHOLD THRESHOLD RANGE RATIO ATTACK ATTACK DECAY RELEASE HOLD GAIN
EQUALIZER LOW
DISPLAY FREQUENCY Q GAIN
dB Hz
LOW MID
FREQUENCY Q GAIN
dB Hz kHz
HIGH MID
FREQUENCY Q GAIN
dB Hz kHz
HIGH
FREQUENCY Q GAIN
dB Hz kHz
EQ ON
kHz
ROUTING
q
DISPLAY
ROUTING
1
2
3
4
t
5
6
q ROUTING [DISPLAY] button w [FOLLOW PAN] button e [STEREO] button r [DIRECT] button t ROUTING [1][8] buttons
7
8
w
FOLLOW PAN STEREO DIRECT
e r
DISPLAY ACCESS
DISPLAY ACCESS
PHASE / INSERT
DELAY
q PHASE/INSERT button w DELAY button
q w
21
02R96
DYNAMICS
w e q
DISPLAY GATE ON COMP ON
r
GATE / COMP GATE COMP
t
DYNAMICS
THRESHOLD THRESHOLD
RANGE RATIO
ATTACK ATTACK
DECAY RELEASE
HOLD GAIN
y
q DYNAMICS [DISPLAY] button w [GATE ON] button e [COMP ON] button r [GATE/COMP] button t [THRESHOLD], [RANGE], [ATTACK], [DECAY], [HOLD] ([THRESHOLD], [RATIO], [ATTACK], [RELEASE], [GAIN]) controls y [GATE/COMP] indicators
PAN/SURROUND
q PAN/SURROUND [DISPLAY] button w [L] & [R] buttons e PAN display r PAN control t [LINK] button y [GRAB] button u [EFFECT] button i Joystick
i q
DISPLAY L
PAN / SURROUND
R
L
ODD
R
EVEN
LINK
GRAB
EFFECT
w
EQUALIZER
e
r
t yu
w e q
DISPLAY FREQUENCY Q GAIN
dB Hz
EQUALIZER LOW
FREQUENCY Q GAIN
dB Hz kHz
LOW MID
HIGH MID
FREQUENCY Q GAIN
dB Hz kHz
HIGH
FREQUENCY Q GAIN
dB Hz kHz
EQ ON
kHz
rt
y
q EQUALIZER [DISPLAY] button w [FREQUENCY/Q] controls e EQ [GAIN] controls r [EQ ON] button t [FREQUENCY/Q] indicators y EQ displays
22
02R96
LAYER
LAYER
q
w
1 24 REMOTE
e
25 48 MASTER
q [124] & [2548] buttons w [REMOTE] button e [MASTER] button
STEREO
STEREO
q
AUTO
w
SEL
e
ON
r
0
5
10
15
q [AUTO] button w [SEL] button e [ON] button r Fader
20
30
40
50 60 70
STEREO
SCENE MEMORY
q
DISPLAY
SCENE MEMORY
STORE
RECALL
we r
t
y
q SCENE MEMORY [DISPLAY] button w Scene memory display e Edit indicator r [STORE] button t Scene Up/Down buttons y [RECALL] button
23
02R96
USER DEFINED KEYS
q
DISPLAY
USER DEFINED KEYS
1
2
3
4
5
6
7
8
w
9
10
11
12
13
14
15
16
q USER DEFINED KEYS [DISPLAY] button w USER DEFINED KEYS [1][16] buttons
MACHINE CONTROL
q w e r
MACHINE CONTROL LOCATE MEMORY
DISPLAY 1 2 3 4
SET
5
6
7
8
t
REW FF
STOP
PLAY
REC
q MACHINE CONTROL [DISPLAY] button w LOCATE MEMORY [1][8] buttons e [SET] button r [REW] button t [FF] button y [STOP] button u [PLAY] button i [REC] button
y
u
i
Data Entry & Transport
t
DEC INC
q
SHUTTLE
y
w
SCRUB
q [SHUTTLE] button w [SCRUB] button e Parameter wheel r [ENTER] button t [DEC] & [INC] buttons y Cursor buttons
e r
ENTER
24
02R96
Monitor, Phones & Talkback Section
t
0 10
TALKBACK LEVEL
r e
PHONES
0
10
0
10
STUDIO LEVEL
PHONES LEVEL
q [STUDIO LEVEL] control w [PHONES LEVEL] control e [PHONES] jack r Talkback mic t [TALKBACK LEVEL] control
q
MONITOR Section
MONITOR
DISPLAY
w
STUDIO
STUDIO
q w r
MONITOR
DISPLAY
CONTROL ROOM
STEREO
STUDIO
AUX7
AUX8
e
CONTROL ROOM STEREO
SOLO
t
AUX7 AUX8
q MONITOR [DISPLAY] button w [CONTROL ROOM] button e [STEREO] button r [AUX 7] button t [AUX 8] button
CLEAR
CONTROL ROOM
2TR D1
2TR A1
SOLO
2TR D2 2TR A2 2TR D3 STEREO
ASSIGN2 ASSIGN1 SURROUND
q w
SOLO
CLEAR
q [SOLO] indicator w [CLEAR] button
BUS
SLOT
0 10 SURROUND MONITOR LEVEL
CONTROL ROOM
0 10 CONTROL ROOM LEVEL
CONTROL ROOM
DIMMER TALKBACK
q w e u o
2TR D1
2TR A1
r t y i !0
2TR D2
2TR A2
2TR D3
STEREO
ASSIGN2 ASSIGN1 SURROUND
BUS
SLOT
!1
0 10 SURROUND MONITOR LEVEL
!2
0 10 CONTROL ROOM LEVEL
!3
DIMMER TALKBACK
!4
q STEREO [2TR D1] button w STEREO [2TR D2] button e STEREO [2TR D3] button r STEREO [2TR A1] button t STEREO [2TR A2] button y [STEREO] button u STEREO [ASSIGN 1] button i STEREO [ASSIGN 2] button o SURROUND [BUS] button !0 SURROUND [SLOT] button !1 [SURROUND MONITOR LEVEL] control !2 [CONTROL ROOM LEVEL] control !3 [DIMMER] button !4 [TALKBACK] button
25
26
02R96
Rear Panel
Analog Master I/O Section (p. 27)
AD Input Section (p. 27)
Power Section (p. 28)
OMNI OUTs, Digital I/O & Control Section (p. 28)
SLOT Section (p. 28)
02R96
AD Input Section
q
q [INPUT A & B (BAL)] connectors w [INSERT I/O +4dB (UNBAL)] connectors (AD 116)
w
q
Analog Master I/O Section
q
w
e
r
t
y
q [STUDIO MONITOR OUT +4 dB (BAL)] connectors w [STEREO OUT +4 dB (BAL)] connectors e [2TR IN ANALOG 1 +4 dB (BAL)] connectors r [CONTROL ROOM MONITOR OUT +4 dB (BAL)] connectors t [STEREO OUT 10 dBV (UNBAL)] connectors y [2TR IN ANALOG 2 10 dBV (UNBAL)] connectors
27
02R96
OMNI OUTs, Digital I/O & Control Section
w q
e
r
ty
u i
o
!0
!1
!2
!3
!4
!5
!6
q [OMNI OUT +4dB (BAL)] connectors w [SMPTE TIME CODE INPUT] connector e [MTC TIME CODE INPUT] connector r [USB TO HOST] port t [SERIAL TO HOST] port y [2TR OUT DIGITAL COAXIAL 2 & 3] connectors u [2TR OUT DIGITAL AES/EBU 1] connector i [2TR IN DIGITAL COAXIAL 2 & 3] connectors o [2TR IN DIGITAL AES/EBU 1] connector !0 [WORD CLOCK OUT] connector !1 [WORD CLOCK 75 ON/OFF] termination switch !2 [WORD CLOCK IN] connector !3 [CONTROL] port !4 [METER] port !5 [MIDI IN, OUT & THRU] ports !6 [CASCADE IN & OUT] ports
Power Section
q [POWER ON/OFF] switch w Grounding screw e [AC IN] connector r Cooling fan
q w e
r
SLOT Section
q
q [SLOT 1][SLOT 4]
28
02R96
MB02R96 Controls
o t
i u
OVER 56
r
e
q Channel indicators w [INPUT METERING POSITION] button & indicators e [PEAK HOLD] button r [LAYER] buttons t [OUTPUT METERING POSITION] button & indicators y Meters u [STEREO] meters i [CONTROL ROOM] button o [BUS] meters
w y
q
29
02R96
CIRCUIT BOARD LAYOUT
02R96 Bottom Assembly
Power supply unit
CPU1 BRG DSP
DA
JK1
JK2 (2/2)
OPT
JK1 DA JK2 (2/2) OPT
JK2 (1/2)
Power supply unit
BRG
DSP
JK2 (1/2)
30
02R96
Rear Assembly U
ANI2 assembly
ANI2
LED
ANI2 assembly
2TRI ST ANI1 #1 AD1 ANI1 #2
ANI1 #3
ANI1 #4 ANI1 #5
ANI1 #6 ANI1 ANI1 #8 ANI1 #7 ANI1 #10 ANI1 ANI1 #9 #11 ANI1 #13 ANI1 #12 #14
ADA
ANI1 ANI1 #15 #16
PHN STD
PHN
STD
ST
2TRI
ANI1
ANI1
ANI1
ANI1
ANI1
ANI1
ANI1
ANI1
ANI2 assembly #16 ANI1 #14 ANI1 #12 ANI1 #10 ANI1 #8 ANI1 #6 ANI1 #4 ANI1 #2 ANI1
#15 #13 #11 #9 #7 #5 #3 #1
AD1
ADA
31
02R96
Control Panel Assembly
JS
PN2
LCD assembly
SUB
PN3
Insulating sheet
FD1
PW
FD2
JS
PN2
LCD assembly Insulating sheet
PN1
PN3 PW
32
02R96
LCD Assembly
LCD
LCDCOM (INV) LCDCOM (CNT)
MB02R96
DC1
PN2
PN1
33
02R96
DISASSEMBLY PROCEDURE
Note: Take care not to trap your fingers.
After replacing the circuit board or fader of FD1 or FD2, please initialize them. (See page 134.)
Disassembling the 02R96 1.
1-1.
Removing the SP02R96
(Time required: About 5 minutes) If the SP02R96 is attached to the 02R96, remove the twelve (12) screws marked [A], and then both sides must be removed. (Fig.1)
02R96
SP02R96(Side pad)
SP02R96 (MB side pad)
[A]
[A]: Bind Head Screw
PW 4.0X20 MFZN2BL (VA314000)
Fig.1
2.
2-1.
Removing the MB02R96
(Time required: About 5 minutes) Remove the two (2) screws marked [35] and the two (2) screws marked [75]. The MB02R96 can then be removed from the 02R96. (Photo.1,2)
MB02R96 Meter angle L, R
[75] [35] 02R96
[35]:Bind Head Screw [75]:Bind Head Screw
A4.0X12 MFZN2BL (VP156900) A4.0X12 MFZN2BL (VP156900)
Photo.1
Photo.2
3.
3-1. 3-2. 3-3.
Control Panel Assembly
(Time required: About 10 minutes) Remove the SP02R96. (See procedure 1.) Remove the MB02R96. (See procedure 2.) Remove the fourteen (14) screws marked [70A], the seven (7) screws marked [70B] and the five (5) screws marked [70C]. (Fig.2) Hold the LCD assembly part, and lift the control panel assembly. And then, fasten them by the two (2) front stays. (Photo.3) When assembling the control panel assembly with the side panel, put the screws of the round screw hole of the side panel in place first, then the screws of the elliptic screw hole.
3-4.
34
02R96
4.
4-1. 4-2. 4-3. 4-4. 4-5.
Rear Assembly U
(Time required: About 15 minutes) Remove the SP02R96. (See procedure 1.) Remove the MB02R96. (See procedure 2.) Fasten the control panel assembly. (See procedure 3.) Remove the two (2) screws marked [30A] and the five (5) screws marked [30B]. (Fig.2) Lift the rear assembly U from the rear side and fasten them by the two (2) rear stays. (There are two ways of using the rear stays shown in the photo 4 or 5.)
Rear assembly U Rear stay
Control panel assembly
Front stay
Photo.3
Photo.4
[30B]
Photo.5
Rear assembly U
[30A]
[70C] [30A]
[70A]
[70A]
Side panel L Control panel assembly
Side panel R
Bottom assembly [70B]
[30]: Bind Head Tapping Screw-B [70]: Bind Head Tapping Screw-B
A4.0X8 MFZN2BL (VC688800) A4.0X8 MFZN2BL (VC688800)
Fig.2
35
02R96
Bottom Assembly Section 5.
5-1. 5-2. 5-3. 5-4.
CPU1 Circuit Board
(Time required: About 15 minutes) Remove the SP02R96. (See procedure 1.) Remove the MB02R96. (See procedure 2.) Fasten the control panel assembly. (See procedure 3.) Remove the four (4) screws marked [590]. The CPU1 circuit board can then be removed. (Fig.4)
6.
6-1. 6-2. 6-3. 6-4.
Replacing the Lithium Battery
(Time required: About 15 minutes) Remove the SP02R96. (See procedure 1.) Remove the MB02R96. (See procedure 2.) Fasten the control panel assembly. (See procedure 3.) You can replace the lithium battery from the CPU1 circuit board. (Fig.4) The lithium battery is not part of the CPU1 circuit board. When you replace the CPU1 circuit board, you should remove the lithium battery from the board, and install in the holder on the new circuit board.
7.
7-1. 7-2. 7-3. 7-4. 7-5. 7-6.
DSP Circuit Board
(Time required: About 25 minutes) Remove the SP02R96. (See procedure 1.) Remove the MB02R96. (See procedure 2.) Fasten the control panel assembly. (See procedure 3.) Fasten the rear assembly U. (See procedure 4.) Remove the CPU1 circuit board. (See procedure 5.) Remove the eight (8) screws marked [560], the four (4) screws marked [575] and the two (2) CPU holders. The DSP circuit board can then be removed. (Fig.5)
8.
8-1. 8-2. 8-3. 8-4. 8-5.
BRG Circuit Board
(Time required: About 20 minutes) Remove the SP02R96. (See procedure 1.) Remove the MB02R96. (See procedure 2.) Fasten the control panel assembly. (See procedure 3.) Fasten the rear assembly U. (See procedure 4.) Remove the six (6) screws marked [410A]. The BRG circuit board can then be removed. (Fig.5)
9.
9-1. 9-2. 9-3. 9-4. 9-5.
Power Supply Unit
(Time required: About 20 minutes) Remove the SP02R96. (See procedure 1.) Remove the MB02R96. (See procedure 2.) Fasten the control panel assembly. (See procedure 3.) Fasten the rear assembly U. (See procedure 4.) Remove the six (6) screws marked [330], the three (3) screws marked [340], the screw marked [350] and the four (4) screws marked [360]. The power supply unit can then be removed. (Fig.5) The power switch knob is not part of the power supply unit. When you replace the power supply unit, you should remove the power switch knob from the power supply unit, and install in the new power supply unit.
36
02R96
10.
10-1. 10-2. 10-3. 10-4. 10-5.
OPT Circuit Board
(Time required: About 20 minutes) Remove the SP02R96. (See procedure 1.) Remove the MB02R96. (See procedure 2.) Fasten the control panel assembly. (See procedure 3.) Fasten the rear assembly U. (See procedure 4.) Remove the four (4) screws marked [390]. The OPT circuit board can then be removed. (Fig.5)
11.
11-1. 11-2. 11-3. 11-4. 11-5.
DA Circuit Board
(Time required: About 20 minutes) Remove the SP02R96. (See procedure 1.) Remove the MB02R96. (See procedure 2.) Fasten the control panel assembly. (See procedure 3.) Fasten the rear assembly U. (See procedure 4.) Remove the three (3) screws marked [520] and the six (6) screws marked [530]. The DA circuit board can then be removed. (Fig.3)
12.
12-1. 12-2. 12-3. 12-4. 12-5. 12-6.
JK1 Circuit Board
(Time required: About 25 minutes) Remove the SP02R96. (See procedure 1.) Remove the MB02R96. (See procedure 2.) Fasten the control panel assembly. (See procedure 3.) Fasten the rear assembly U. (See procedure 4.) Remove the DA circuit board. (See procedure 11.) Remove the three (3) screws marked [460A], the nine (9) screws marked [480A] and the four (4) screws marked [490]. The JK1 circuit board can then be removed. (Fig.4)
13.
13-1. 13-2. 13-3. 13-4. 13-5. 13-6. 13-7.
JK2 (1/2) Circuit Board
(Time required: About 30 minutes) Remove the SP02R96. (See procedure 1.) Remove the MB02R96. (See procedure 2.) Fasten the control panel assembly. (See procedure 3.) Fasten the rear assembly U. (See procedure 4.) Remove the DA circuit board. (See procedure 11.) Remove the JK1 circuit board. (See procedure 12.) Remove the three (3) screws marked [460B], the two (2) screws marked [480B], the two (2) screws marked [B] and the four (4) screws marked [C]. The JK2 (1/2) circuit board can then be removed. (Fig. 5)
14.
14-1. 14-2. 14-3. 14-4. 14-5.
JK2 (2/2) Circuit Board
(Time required: About 20 minutes) Remove the SP02R96. (See procedure 1.) Remove the MB02R96. (See procedure 2.) Fasten the control panel assembly. (See procedure 3.) Fasten the rear assembly U. (See procedure 4.) Remove the two (2) screws marked [500]. The JK2 (2/2) circuit board can then be removed. (Fig. 5)
37
02R96
15.
15-1. 15-2. 15-3. 15-4. 15-5.
DC Fan Motor
(Time required: About 20 minutes) Remove the SP02R96. (See procedure 1.) Remove the MB02R96. (See procedure 2.) Fasten the control panel assembly. (See procedure 3.) Fasten the rear assembly U. (See procedure 4.) Remove the four (4) screws marked [140A]. The DC fan motor, the four (4) fan vibration absorbing rubbers, the fan guide, the fan guard and the four (4) toothed lock washers can then be removed. (Fig.3) When you install the DC fan motor, be sure to attach the screw lock.
DC fan motor Fan vibration absorbing rubber Fan guide
[140A] x 4 Fan guard
[520]
DA
JK2 (2/2)
[140A]
[530]
[500]
[140A]:Bind Head Screw [500]: Hex. Locking Screw [520]: Bind Head Tapping Screw-B [530]: Bonding Tapping Screw-B
4.0X40 MFZN2BL (VV413200) JFS-2.6S-BIW (VS604900) 3.0X8 MFZN2BL (EP600190) 3.0X8 MFZN2BL (VN413300)
Fig.3
38
02R96
CPU1
[590]
Lithium Battery
Battery VN103500
VN103600(Battery holder for VN103500)
Notice for back-up battery removal Push the battery as shown in figure, then the battery will pop up. Druk de batterij naar beneden zoals aangeven in de tekening de batterij springt dan naar voren.
Battery
Battery holder
JK1
[460A] [490]
[480A]
[460A]:Bind Head Tapping Screw-B [480A]:Bonding Tapping Screw-B [490]: Bonding Screw [590]: Bind Head Screw
3.0X8 MFZN2BL (EP600190) 3.0X8 MFZN2BL (VN413300) 3.0X8 MFZN2BL (VP157800) 3.0X8 MFZN2BL (VB659000)
Fig.4
39
02R96
OPT
[390]
[410A]
[560]
[330]
CPU holder
Power supply unit
[575]
CPU holder
BRG
[340]
DSP
[560]
[330]
[350] Side panel R [460B]
JK2 (1/2)
[360] Power switch knob [360] [B] [480B] [C]
[330]: Bind Head Tapping Screw-B [340]: Bind Head Tapping Screw-B [350]: Bind Head Tapping Screw-S [360]: Bonding Screw [390]: Bind Head Screw [410A]:Bind Head Tapping Screw-B [460B]:Bind Head Tapping Screw-B [480B]:Bonding Tapping Screw-B [560]: Bind Head Tapping Screw-B [575]: Bind Head Tapping Screw-B
3.0X8 MFZN2BL (EP600190) A4.0X8 MFZN2BL (VC688800) 4.0X8 MFZN2BL (VI693100) 3.0X8 MFZN2BL (VP157800) SP 4.0X8 MFZN2Y (VZ538000) 3.0X8 MFZN2BL (EP600190) 3.0X8 MFZN2BL (EP600190) 3.0X8 MFZN2BL (VN413300) 3.0X8 MFZN2BL (EP600190) 3.0X8 MFZN2BL (EP600190)
Fig.5
40
02R96
Rear Assembly U Section 16.
16-1. 16-2. 16-3. 16-4.
PC Support
(Time required: About 15 minutes) Remove the SP02R96. (See procedure 1.) Remove the MB02R96. (See procedure 2.) Fasten the control panel assembly. (See procedure 3.) Remove the eleven (11) screws marked [260A], the twenty-four (24) nuts marked [270], the four (4) nuts marked [280] and the twenty-seven (27) knobs marked [300]. The PC support can then be removed from the rear assembly U. (Fig.6)
17.
17-1. 17-2. 17-3. 17-4. 17-5.
ANI1 Circuit Board
(Time required: About 20 minutes) Remove the SP02R96. (See procedure 1.) Remove the MB02R96. (See procedure 2.) Fasten the control panel assembly. (See procedure 3.) Remove the PC support. (See procedure 16.) Remove the three (3) screws marked [200A] and disconnect the connector from the AD1 circuit board or the ADA circuit board. The ANI circuit board can then be removed. (Fig.6) There is a total of sixteen (16) ANI1 circuit boards, and they can all be removed in this way.
18.
18-1. 18-2. 18-3. 18-4. 18-5.
ANI2 and LED Circuit Boards
(Time required: About 20 minutes) Remove the SP02R96. (See procedure 1.) Remove the MB02R96. (See procedure 2.) Fasten the control panel assembly. (See procedure 3.) Remove the PC support. (See procedure 16.) Remove the screw marked [200A] and disconnect the connector from the ADA circuit board. The ANI2 assembly can then be removed. (Fig.6) There is a total of four (4) ANI2 assembly, and they can all be removed in this way. 18-6. Remove the LED circuit board from the connector and the locking card spacer on the ANI2 circuit board. The ANI2 circuit board and the LED circuit board can then be divided. (Fig.6)
41
02R96
19.
19-1. 19-2. 19-3. 19-4. 19-5.
2TRI, ST, STD, PHN Circuit Boards
(Time required: About 20 minutes each) Remove the SP02R96. (See procedure 1.) Remove the MB02R96. (See procedure 2.) Fasten the control panel assembly. (See procedure 3.) Remove the PC support. (See procedure 16.) 2TRI Circuit Board: Remove the two (2) screws marked [200C] and disconnect the connector from the ADA circuit board. The 2TRI circuit board can then be removed. (Fig.6) 19-6. ST Circuit Board: Remove the five (5) screws marked [200D] and disconnect the connector from the ADA circuit board. The ST circuit board can then be removed. (Fig.6) 19-7. STD Circuit Board: Remove the two (2) screws marked [200E] and disconnect the connector from the ADA circuit board. The STD circuit board can then be removed. (Fig.6) 19-8. PHN Circuit Board: Remove the two (2) screws marked [210A] and disconnect the connector from the ADA circuit board. The PHN circuit board can then be removed. (Fig.6)
20.
20-1. 20-2. 20-3. 20-4. 20-5.
AD1 Circuit Board
(Time required: About 25 minutes) Remove the SP02R96. (See procedure 1.) Remove the MB02R96. (See procedure 2.) Fasten the control panel assembly. (See procedure 3.) Remove the PC support. (See procedure 16.) Remove the twelve (12) ANI1 circuit boards. (See procedure 17.) 20-6. Remove the eight (8) screws marked [120A]. The AD1 circuit board can then be removed. (Fig.7)
21.
21-1. 21-2. 21-3. 21-4. 21-5.
ADA Circuit Board
(Time required: About 25 minutes) Remove the SP02R96. (See procedure 1.) Remove the MB02R96. (See procedure 2.) Fasten the control panel assembly. (See procedure 3.) Remove the PC support. (See procedure 16.) Remove the four (4) ANI1 circuit boards. (See procedure 17.) 21-6. Remove the four (4) ANI2 assemblies. (See procedure 18-5.) 21-7. Remove the 2TRI, ST, STD and PHN circuit boards. (See procedure 19.) 21-8. Remove the eight (8) screws marked [120B]. The ADA circuit board can then be removed. (Fig.7)
42
02R96
ANI2 assembly
[300] x 27 [270] x 24
Locking card spacer
ANI2 assembly x 4
ANI2 2TRI
LED
ANI1 x 16
ST
[260A] x 11
AD1
ADA
[280] PC support
STD PHN
[210A]
[200A] x 48
[200E]
[200D]
[200C]
[200B] x 4
[200]: Bonding Tapping Screw-B [210A]:Bind Head Screw [260A]:Bind Head Tapping Screw-B [270]: Hexagonal Nut [280]: Hexagonal Nut
3.0X8 MFZN2BL (VN413300) A4.0X8 MFZN2BL (VP156800) A4.0X8 MFZN2BL (VC688800) 7.0X11X2 MFZN2BL (VR991600) 9.0X11X2 MFZN2BL (VJ388000)
Fig.6
Rear panel U
AD1
ADA
[120A]
[120B]
[120]:Bind Head Tapping Screw-B
3.0X8 MFZN2BL (EP600190)
Fig.7
43
02R96
Control Panel Assembly Section
When removing the circuit board, if it is hard to handle while the control panel assembly is fixed slantwise at the front stay, open it widely at 180° for the work.
22.
22-1. 22-2. 22-3. 22-4.
SUB Circuit Board
(Time required: About 15 minutes) Remove the SP02R96. (See procedure 1.) Remove the MB02R96. (See procedure 2.) Fasten the control panel assembly. (See procedure 3.) Remove the eight (8) screws marked [180A]. The SUB circuit board can then be removed. (Fig.9)
23.
PN1 Circuit Board
(Time required: About 20 minutes) 23-1. Remove the SP02R96. (See procedure 1.) 23-2. Remove the MB02R96. (See procedure 2.) 23-3. Remove the four (4) encoder knobs marked [410B] and the sixteen (16) encoder knobs marked [450A] from the control panel side. (Fig.8) 23-4. Fasten the control panel assembly. (See procedure 3.) 23-5. Remove the SUB circuit board. (See procedure 22.) 23-6. Remove the twenty (20) screws marked [160A]. The PN1 circuit board can then be removed with the SUB1 and SUB2 holders. (Fig.10)
24.
24-1. 24-2. 24-3. 24-4.
JS Circuit Board
(Time required: About 15 minutes) Remove the SP02R96. (See procedure 1.) Remove the MB02R96. (See procedure 2.) Fasten the control panel assembly. (See procedure 3.) Remove the four (4) screws marked [160B]. The JS circuit board can then be removed. (Fig.10)
25.
PN2 Circuit Board
44
(Time required: About 25 minutes) 25-1. Remove the SP02R96. (See procedure 1.) 25-2. Remove the MB02R96. (See procedure 2.) 25-3. Remove the encoder knob marked [410C], the five (5) encoder knobs marked [420], the eight (8) encoder knobs marked [440], the eight (8) encoder knobs marked [450B], the knob marked [460C] and the knob marked [470] from the control panel side. (Fig.8) 25-4. Fasten the control panel assembly. (See procedure 3.) 25-5. Remove the JS circuit board. (See procedure 24.) 25-6. Remove the twenty-two (22) screws marked [165]. The PN2 circuit board can then be removed with the insulating sheet. (Fig.10) 25-7. Remove the five (5) cord holders. The insulating sheet can then be removed from the PN2 circuit board. (Fig.10) The insulating sheet is fastened to the PN2 circuit board by the cord holders. When you replace the PN2 circuit board, be sure to attach the insulating sheet as before.
02R96
26.
PN3+PW Circuit Boards
(Time required: About 20 minutes) 26-1. Remove the SP02R96. (See procedure 1.) 26-2. Remove the MB02R96. (See procedure 2.) 26-3. Remove the encoder knob and the hexagonal nut from the control panel side. (Fig.8, Photo.6) 26-4. Fasten the control panel assembly. (See procedure 3.) 26-5. Remove the six (6) screws marked [160C]. The PN3+PW circuit boards can then be removed. (Fig.10)
27.
FD1 Circuit Board
(Time required: About 20 minutes) 27-1. Remove the SP02R96. (See procedure 1.) 27-2. Remove the MB02R96. (See procedure 2.) 27-3. Remove the sixteen (16) fader knobs marked [400A] from the control panel side. (Fig.8) 27-4. Fasten the control panel assembly. (See procedure 3.) 27-5. Remove the twelve (12) screws marked [210B]. The FD1 circuit board can then be removed. (Fig.9)
28.
FD2 Circuit Board
(Time required: About 25 minutes) 28-1. Remove the SP02R96. (See procedure 1.) 28-2. Remove the MB02R96. (See procedure 2.) 28-3. Remove the nine (9) fader knobs marked [400B] from the control panel side. (Fig.8) 28-4. Fasten the control panel assembly. (See procedure 3.) 28-5. Remove the six (6) screws marked [210C]. The FD2 circuit board can then be removed with the insulating sheet. (Fig.9) 28-6. Remove the four (4) cord holders. The insulating sheet can then be removed from the FD2 circuit board. (Fig.9) The insulating sheet is fastened to the FD2 circuit board by the cord holders. When you replace the FD2 circuit board, be sure to attach the insulating sheet as before.
29.
LCD Assembly
(Time required: About 5 minutes each) 29-1. Remove the eight (8) screws marked [260B] from the control panel side. The LCD assembly can then be removed. (Fig.8) Be careful no to scratch the control panel during installation.
45
02R96
Hexagonal nut
Encoder knob Control panel
Photo.6
LCD assembly
[260B] x 8
Joy stick knob [410C] [420] x 5 [440] x 8 [470] [460C] [450A] x 16 [450B] x 8
[410B]
[400A] x 16
[400B] x 9
Encoder knob
[260B]:Flat Head Tapping Screw-B
3.0X8 MFZN2BL (EP600790)
Fig.8
46
02R96
[180A] x 8
SUB
[210B] x 12
Insulating sheet
FD2
FD1
[210C] x 6
Cord holder
[180A]: Bind Head Tapping Screw-B [210]: Bind Head Tapping Screw-B
3.0X8 MFZN2BL (EP600190) 3.0X8 MFZN2BL (EP600190)
Fig.9
[160B]
JS
[165] x 22 [160A] x 20
PN2
Cord holder
PN1
SUB2 holder Insulating sheet
SUB1 holder
PN3 PW
[160C] x 6
[160]: Bind Head Tapping Screw-B [165]: Bind Head Tapping Screw-B
3.0X8 MFZN2BL (EP600190) 3.0X8 MFZN2BL (EP600190)
Fig.10
47
02R96
[180B] LCD bracket [120C]
Rear LCD case [120C] [120C]
[125]
[120C]: Bind Head Tapping Screw-B [125]: Bind Head Tapping Screw-B [180B]: Bind Head Tapping Screw-B
A4.0X8 MFZN2BL (VC688800) A3.0X6 MFZN2BL (VP157900) A4.0X8 MFZN2BL (VC688800)
Fig.11
LCD case assembly
[40]
[40]
[80A]
LCD
[60]
LCDCOM (CNT)
[100] LCD shield panel
[100]
LCDCOM (INV)
[40]: Bind Head Tapping Screw-B [60]: Bind Head Tapping Screw-B [80A]: Bind Head Tapping Screw-B [100]: Bind Head Tapping Screw-B
3.0X6 MFZN2BL (EP600230) 3.0X6 MFZN2BL (EP600230) 3.0X6 MFZN2BL (EP600230) 3.0X6 MFZN2BL (EP600230)
Fig.12
48
02R96
30.
LCDCOM (CNT+INV) Circuit Board and LCD (Time required: About 15 minutes each)
30-1. Remove the LCD assembly. (See procedure 29.) 30-2. Remove the four (4) screws marked [180B]. The LCD bracket can then be removed. (Fig.11) 30-3. Remove the six (6) screws marked [120C] and the five (5) screws marked [125]. The rear LCD case can then be removed. (Fig.11) 30-4. Remove the two (2) screws marked [60] and the four (4) screws marked [80A]. The LCD shield panel can then be removed with the LCDCOM (CNT+INV) circuit board. (Fig.12) 30-5. LCDCOM (CNT+INV) Circuit Board: Remove the four (4) screws marked [100]. The LCDCOM (CNT+INV) circuit board can then be removed from the LCD shield panel. (Fig.12) The CNT and INV circuit boards are joined by soldering. Note: The INV circuit board must be handled carefully since it produces high voltages. 30-6. LCD: Remove the four (4) screws marked [40]. The LCD can then be removed. (Fig.12)
Disassembling the MB02R96 31. Rear Panel
(Time required: About 10 minutes) 31-1. Remove the MB02R96. (See procedure 2.) 31-2. Remove the two (2) screws