019AADJ.pdf part of lg rt21-fa32x RT-21FA32X.part1.rar, sm tv lg rt21-fa32x text manual preview

Text preview for : 019AADJ.pdf part of lg rt21-fa32x sm tv lg rt21-fa32x

Back to : RT-21FA32X.part1.rar | Home

ADJUSTMENT
O

Safety Precautions
1. It is safe to adjust after using insulating transformer between the power supply line and chassis input to prevent the risk of electric shock and protect the instrument. 2. Never disconnect leads while the TV receiver is on. 3. Don't short any portion of circuits while power is on. 4. The adjustment must be done by the correct appliances. But this is changeable in view of productivity. 5. Unless otherwise noted, set the line voltage to 110~240Vac !10%, 50/60Hz. 6. The adjustment of TV should be performed afther warming up for 20 minutes.

Option TBS EYE

Code 0 1 0 1 0

Function W/O TBS WITH TBS W/O EYE WITH EYE W/O 4 KEY WITH 4 KEY

Remark

4 KEY MONO

1 0 1

FORCED MONO

Table 2. OPTION 2 Function
Option BCF Code 0 1 0 GAME 200 PRO CHA + AU DUAL 1 0 1 0 1 0 1 0 ACMS T-SCH 1 0 1 0 1 0 CURVE 1 Function Auto Abnormal ON Not Used W/O GAME PACK WITH GAME PACK 100 PRO 200 PRO Except China,Austrailia China,Austrailia W/O DUAL WITH DUAL Austrailia Except Austrailia W/O TURBO SEARCH WITH TURBO SEARCH W/O TURBO P/S WITH TURBO P/S NORMAL VOLUME CURVE M-A,India VOLUME CURVE Remark

O

Test Equipment required
1. Multimeter (volt meter) 2. Oscilloscope 3. 10:1 PROBE 4. Color Analyzer

O

CDL Data Adjustment(LINE SVC-0)
1) Press the SVC button to get into the SVC-0 Mode. 2) Press the Channel UP/DOWN button to select CDL12. 3) Press the Volume UP/DOWN button until the CDL data is the same as the Table below. 21" FCD CDL Data Remark 12 FLAT 14,16" CPT 8 15" CPT 10 FLAT 20,21" CPT 12

4) Press the OK(V) button to memorize the data.
O

OPTION Data Adjustment(OPTION-1,OPTION-2)
1) Press OK buttons on both TV set and Remote Controller at the same time to get into SVC mode. 2) Press the Yellow button several times to find OPTION-1 or OPTION-2. 3) Input the correspond OPTION data referring to Table below with the numeric buttons. 4) Press the OK(V) button to memorize the data. T-P/S

Table 3. OPTION 3 Function
Option Code Function *** *** W/O HOTEL W/HOTEL BG/L BG/I/DK BG/I/DK/M BG/I/DK DUAL BG/I/DK/M DUAL 2nd IF BG 2nd IF I 2nd IF DK Remark

Table 1. OPTION 1 Function
Option C MUTE DVD 2 IN 1 Code 0 1 0 1 0 1 0 1 0 SCART 1 Function ACTIVE NOT ACTIVE W/O DVD DVD(REAR JACK) W/O 2 IN 1TUNER WITH 2 IN 1TUNER FLOF TXT TOP TXT PHONO JACK SCART JACK Remark

RESER VED HOTEL

0 1 0 1 0 1 2

TOP

SYSTEM

3 4 5 6 7

- 11 -

Option Code 0 OSD-L (EU) 1 2

Function ENG. ONLY EU-7EA EU ALL

Remark English English,Deutsch,Francais,Italiano,Espanol English,Nederlands,Svenska,Dansk,Suomi,Por tugues,Romaneste,Polski,Cesky,Pyccknn

O

FOCUS Adjustment
Test Point Adjust : RK (Red Cathode of CPT Board) : Screen Volume of FBT

3 0 OSD-L (MASIA) 1 2 3 OSD-L (E-ASIA) OSD-L (CH+HI) 0 1 0 1 2 0 TXT-L (EU) 1 2 3 TXT-L (E-ASIA) TXT-L (ARAB) TXT-L (FARSI) 0

EU EAST ENG. ONLY ARABIC PARSI ARAB,FARSI,URDE ENG.ONLY ASIA-ALL ENG.ONLY E+CHINA E+HINDI W-EU E-EU CYRILLIC UKRAINIAN WEST-EU

English,Romaneste,Polski,Cesky,Pyccknn,Magyar English English,Arab,,Urdu,French English,Parsi,Urdu,French English,French,Arab,Urdu,Parsi English English,Malay,Vietnam,Indonesian,Thai English English,Chinese English,Hindi
O

1) Tune the TV set to receive a PAL 05CH. 2) Adjust the Focus Volume of FBT for best focus.

Screen Voltage Adjustment
Test Point Adjust : Observing Display : Focus Volume of FBT

1) Connect the probe of oscilloscope to the RK (Red Cathode) of CPT Board. 2) Set the oscilloscope to 50V/div and 20Us/div and after putting GND line upon the lowest grid line of the scope by pressing GND button,enter into DC mode. 3) Tune the TV set to receive a PAL-B/G 05CH. 4) Adjust Screen Volume of FBT so that the waveform is the same as below figure (DC 140!3V).
Horizontal FlyBack Time

Black level 140Vp-p

0 1 0 1

WEST-EU ARABIC WEST-EU FARSI 14" DC 130V!3 V
O
White level GND for dc

OTHERS DC 140V!3 V

O

AGC Adjustment (SERVICE 1)
Test Point Adjust : AGC TP (C101) : Remote Controller

White Balance Adjustment.(LINE SVC-0)

NOTE : This adjustment should be performed after screen voltage adjustment. 1) Tune the TV set to receive an 100% white pattern. 2) Press OK(V) buttons on TV set and remote controller at the same time to get into SVC mode. 3) Press Yellow button on remote controller. (Standard mode) 4) Press Channel UP/DOWN button for desirous function adjustment. 5) Adjust VOL+ or VOL-button in each status of "RG--"/"BG--" for X=272!8, Y=288!8 with color analyzer.(Europe Model : X=288!8, Y=295!X=272!8, 11,000K) Status Initial Data 31 31 31 31 31 Remark

1) Connect RF signal (70dB!0.2dB) and turn on the TV. � Standard adjustment Channel - EU 05 Ch. (frf = 175.25MHz) 2) Press the OK buttons on TV set and Remote Controller at the same time to get into SVC-0 mode. 3) Press the Channel UP/DOWN button on the Remote Controller several times to find AGC??. 4) Press the Volume UP/DOWN button until the AGC Voltage is the same as the Table below. 5) Press the OK(V) button to memorize the data. Tuner P/N Marker AGC Voltage Tuner P/N Marker AGC Voltage 6700VPF009G LG Innotek(W/S TUNER) 2.7! 0.05V 6700VPF009S LG Innotek(TBS TUNER) 2.5! 0.05V 6700VPF016A DAEWOO(W/S TUNER) 2.7! 0.05V

RG GG BG BLO-R BLO-G

7) Press the OK(V) button to memorize the data.

- 12 -

O

Deflection Data Adjustment (Line SVC-1)
NOTE: To enter SVC mode, press "OK" buttons on both TV set and the Remote control at the same time.

1. Preparation for Deflection Adjustment
1) At SVC mode, press the Yellow colored button. And then, deflection data adjustment OSD (SVC1 mode) will be displayed. 2) Tune the TV set to receive a PAL 05 CH and set the ARC mode is standard.

2. Deflection Initial Setup Data
Status VL VA VS HS SC Default 31 31 31 31 25 21" FLAT S/S 31 31 31 31 25 21" FLAT LG 31 31 31 31 25

3. Deflection Adjustment Procedure
VL (Vertical Linearity) Adjust so that the boundary line between upper and lower half is in accord with geometric horizontal center of the CPT. VA (Vertical Amplitude) Adjust so that the circle of a digital circle pattern may be located within the effective screen of the CPT. SC (Vertical "S" Correction) Adjust so that all distance between each horizontal lines are to be the same. VS (Vertical Shift) Adjust so that the horizontal center line of a digital circle pattern is in accord with geometric horizontal center of the CPT.

HS (Horizontal Shift) Adjust so that the vertical center line of a digital circle pattern is in accord with geometric vertical center of the CPT. Press the OK(V) button to memorize the data.

- 13 -