Text preview for : 8050_disassembly.pdf part of lg wd-1050f servise manual wd-1050f
Back to : wd-1050f.rar | Home
9. DISASSEMBLY INSTRUCTIONS
RBe sure to unplug the machine out of the outlet before disassembling and repairing the parts.
CONTROL PANEL
€ Unscrew 2 screws on the back of the top plate. €LPull the top plate backward and upward as shown.
PLATE ASSY(TOP)
€ Disconnect the PWB assy (Display) connector.
Hook
€LPull out the drawer and unscrew 3 screws. €ØPush 2 upper hooks down and pull the control panel.
PANEL ASSY(CONTROL)
PWB ASSY(DISPLAY)
€ Disconnect the PWB assy (Display) from the control panel by unscrewing 9 screws.
24
PWB ASSY(POWER)
€ Disassemble the top plate assy. €LUnscrew 2 screws. €ØDisconnect connector from the wiring.
DISPENSER ASSY
€ Disassemble the top plate assy. €LPull out the drawer slightly upward. €ØUnscrew 2 screws.
DRAWER
€ Disassemble hose clamps and hoses €LDisassemble ventilation bellows and water inlet bellows from tub.
DISPENSOR ASSY
25
INLET VALVE
2 1
€ Disconnect the wiring receptacle. €L Unscrew 2 screws from the back. ¡ When reconnecting the connector
VALVE#1(MAIN) VALVE#2(PRE) VALVE#3(HOT)
(Option) € Unscrew 2 screws
White/Black - Black Gray/White - Black Blue/Red - Black
REACTOR
€L Disconnect the wiring connector from the PWB assy(Msin)
PWB ASSY(MAIN)
€ Unscrew 2 screws €LPull the PWB assy(Main) as shown.
LOWER COVER
¡Æ Open the lower cover plate by using coin and pull out the lower cover in the arrow direction after a screw is unscrewed.
26
DOOR
€ Open the door completely. €LRemove the two screws from the hinge.
GASKET ASSY
€ Take apart the cabinet gasket clamp. €LUnscrew 2 screws from the cabinet cover. €ØOpen the lower cover cap and unscrew 1 screw inside €OETake apart the lower cover
€ Unscrew all the screws on the upper and lower sides of the cabinet cover.
€ Take apart the tub gasket clamp €LMake sure that the drain hole of the gasket is put beneath when reassembling the gasket. ¡ Refer to the arrow mark on the tub cover.
27
PULLEY, MOTOR, DAMPER
€ Remove the back cover. €LTake off the belt turning the pulley. €ØUnscrew the bolt to pull out the pulley.
(PULLEY)
€ Unscrew 2 screws from the bracket. €LPush the motor in the arrow direction for disassembling. €ØWhen reassembling the motor, make sure that motor
1 3
mounting rubbers are not taken off from the bracket.
2
(MOTOR)
Hinge, Damper
Damper
€ Pull out the hinge pressing its snap. €LDo not use the pulled out hinge again..it may be taken off during operation.
(DAMPER)
§ Clean the drain pump filter
100
3 2
1
3
2
Open the lower cover cap ( ¥L ) by using coin.Turn the drain plug ( ¥M) to pull out the hose.
Unplug the drain plug ( ¥M) , then the water flows out, At this time use a vessel to prevent water flowing on the floor. If the water does not flow any more,turn the pump filter ( ¥N) open to the left. Take out any foreign material
from the pump filter ( ¥N). After cleaning, turn the pump filter(¥N) clockwise and insert the drain plug ( ¥M)to the original place. close the lower cover cap.
28
PUMP
Pump Outlet Hose
€ Remove pump outlet hose. €LRemove tub pump bellows. €ØRemove cap(Remaining Hose.) €OEDisconnect the wiring. €ºUnscrew 3 screws € Remove the pump.
Screw
Cap (Remaining Hose)
Tub Pump Bellows
HEATER
€ Unscrew 3 screws fixing the heater protecting cover. €LLoosen the M6 heater nut to pull out the heater.
CAUTION
When mounting the heater, be sure to insert the heater into the heater clip on the bottom of the tub.
THERMISTOR
€ Pull it out by holding the thermistor bracket. TIf it is pulled by the wire, it may be broken. €LWhen mounting the thermistor again, make sure that it is got back tight to the rubber.
29
DOOR HINGE ASSY
€ Disassemble the door from the door hinge. €LTake apart the cabinet cover clamp and release the gasket. €ØUnscrew 2 screws on the door hinge. €OEPush the door hinge arm to the inside of the cabinet cover for disassembling.
SWITCH ASSY, DOOR LOCK
€ Take apart the cabinet cover clamp and release the gasket. €LUnscrew 2 screws holding the Door Lock. €ØDisconnect the door lock from the wiring connector.
WHEN FOREIGN MATERIAL IS STUCK BETWEEN DRUM AND TUB
€ Remove the heater. €LRemove the foreign material (wire, coin and others) by inserting a long bar through the hole.
30