Text preview for : Yamaha-MG206C mix.pdf part of Yamaha MG206C mixer (also USB)
Back to : Yamaha-MG206C mix.part1.r | Home
SERVICE MANUAL
MG206C-USB MG206C
I CONTENTS
SPECIFICATIONS .................................................................. 3/5
DIMENSIONS .............................................................................. 7
PANEL LAYOUT ......................................................... 8
CIRCUIT BOARD LAYOUT .................................. 11
WIRING DIAGRAM ............................................................. 12
OVERALL ASSEMBLY WIRING ........................................ 13
DISASSEMBLY PROCEDURES ............................................. 19
LSI PIN DESCRIPTION .................................................. 24
IC BLOCK DIAGRAM ...................................................... 24
CIRCUIT BOARDS ........................................................... 27
INSPECTIONS .......................................................................... 37/44
PARTS LIST
IC & DIODE FIGURES
This document is printed on chlorine free (ECF) paper.
BLOCK & LEVEL DIAGRAM
CIRCUIT DIAGRAM
PA 011870
MG206C: 200708-94290
MG206C-USB: 200708-102690 HAMAMATSU, JAPAN
Copyright (c) Yamaha Corporation. All rights reserved. 07.08
MG206C-USB/MG206C
IMPORTANT NOTICE
This manual has been provided for the use of authorized Yamaha Retailers and their service personnel. It has been assumed that basic service
procedures inherent to the industry, and more specifically Yamaha Products, are already known and understood by the users, and have
therefore not been restated.
WARNING: Failure to follow appropriate service and safety procedures when servicing this product may result in personal injury, destruc-
tion of expensive components and failure of the product to perform as specified. For these reasons, we advise all Yamaha
product owners that all service required should be performed by an authorized Yamaha Retailer or the appointed service
representative.
IMPORTANT: This presentation or sale of this manual to any individual or firm does not constitute authorization, certification, recognition of
any applicable technical capabilities, or establish a principal-agent relationship of any form.
The data provided is believed to be accurate and applicable to the unit(s) indicated on the cover. The research engineering, and service
departments of Yamaha are continually striving to improve Yamaha products. Modifications are, therefore, inevitable and changes in specifica-
tion are subject to change without notice or obligation to retrofit. Should any discrepancy appear to exist, please contact the distributor's Service
Division.
WARNING: Static discharges can destroy expensive components. Discharge any static electricity your body may have accumulated by
grounding yourself to the ground bus in the unit (heavy gauge black wires connect to this bus).
IMPORTANT: Turn the unit OFF during disassembly and parts replacement. Recheck all work before you apply power to the unit.
WARNING: CHEMICAL CONTENT NOTICE!
The solder used in the production of this product contains LEAD. In addition, other electrical/electronic and/or plastic (Where applicable)
components may also contain traces of chemicals found by the California Health and Welfare Agency (and possibly other entities) to cause
cancer and/or birth defects or other reproductive harm.
DO NOT PLACE SOLDER, ELECTRICAL/ELECTRONIC OR PLASTIC COMPONENTS IN YOUR MOUTH FOR ANY REASON WHAT SO
EVER!
Avoid prolonged, unprotected contact between solder and your skin! When soldering, do not inhale solder fumes or expose eyes to solder/flux
vapor!
If you come in contact with solder or components located inside the enclosure of this product, wash your hands before handling food.
IMPORTANT NOTICE FOR THE UNITED KINGDOM
Connecting the Plug and Cord
WARNING: THIS APPARATUS MUST BE EARTHED
IMPORTANT. The wires in this mains lead are coloured in accordance with the following code:
GREEN-AND-YELLOW: EARTH
BLUE: NEUTRAL
BROWN: LIVE
As the colours of the wires in the mains lead of this apparatus may not correspond with the coloured markings identifying the terminals in your
plug, proceed as follows:
The wire which is coloured GREEN and YELLOW must be connected to the terminal in the plug which is marked by the letter E or by the safety
earth symbol or colored GREEN or colored GREEN and YELLOW.
The wire which is coloured BLUE must be connected to the terminal which is marked with the letter N or coloured BLACK.
The wire which is coloured BROWN must be connected to the terminal which is marked with the letter L or coloured RED.
I WARNING
Components having special characteristics are marked and must be replaced with parts having specification equal to those originally
installed.
2
MG206C-USB/MG206C
I SPECIFICATIONS
· Electrical Specifications
· General Specifications
3
MG206C-USB/MG206C
· Analog Input Specifications
· Analog Output Specifications
· Digital Input/Output Specifications (MG206C-USB only)
4
MG206C-USB/MG206C
5
MG206C-USB/MG206C
6
MG206C-USB/MG206C
I DIMENSIONS
444
102
5
478 98
496
488.5
43
41
Unit: mm
MG206C-USB
7
MG206C-USB/MG206C
I PANEL LAYOUT
· Channel Control Section
Channels Channels Channels Channels 1 MIC Input Jacks
1 to 8 9 to 12 13/14 and 15/16 17/18 and 19/20 2 LINE Input Jacks (monaural channels)
(Monaural) (Monaural) (Stereo) (Stereo)
3 LINE Input Jacks (stereo channels)
4 LINE Input Jacks (stereo channels)
5 INSERT Jacks
6 GAIN Control
7 80 Switch (High-Pass Filter)
1 1
8 COMP Control
9 PEAK Indicator
2 0 Equalizer (HIGH, MID and LOW)
3 4
5 A AUX, EFFECT Control
B AUX PRE Switch
C PAN Control
PAN/BAL Control
BAL Control
6 6
D ON Switch
7 7 E PFL (Pre-Fader Listen) Switch
8 F 1-2 Switch
G 3-4 Switch
9 9 H ST Switch
I Channel Fader
0 0
1
2
3
A A 4
5
6
B B 7
8
9
0
C C A
B
C
D D
E E
D
F F E
G G F
H H G
H
I
I I
8
MG206C-USB/MG206C
· Master Control Section
1 USB Connector (MG206C-USB only)
Rear panel 2 4 5 6 2 SEND Jacks (AUX, EFFECT)
3 GROUP OUT (1 to 4) Jacks
4 REC OUT (L, R) Jacks
5 2TR IN Jacks
1 6 RETURN L (MONO), R Jacks
7 STEREO OUT (L, R) Jacks
3 · XLR Jacks
· LINE Jacks
8 MONITOR OUT Jacks
9 PHONES Jack
0 PHANTOM +48 V Switch
K L A POWER Indicator
B Level Meter
7 C RETURN
· AUX1, AUX2 Control
· STEREO Control
D Master SEND Controls (AUX, EFFECT)
E MONITOR/PHONES
· MONITOR Switches
· MONITOR Control
9 F 2TR IN (MG206C)
8 2TR IN/USB (MG206C-USB)
· 2TR IN/USB Switch
· 2TR IN/USB Control
G GROUP 1-2 Fader
H GROUP 3-4 Fader
0 A I ST Switch
J STEREO OUT Master Fader
K POWER Switch
L AC ADAPTOR IN Connector
B
1
2
3
4
5
D 6
7
C
E 8
9
0
A
B
C
F D
E
I
F
H G
H
I
G J J
K
L 9
MG206C-USB/MG206C
· Connector Polarities
Input and Output Jacks Polarities Configurations
INPUT OUTPUT
Pin 1: Ground
MIC INPUT, STEREO OUT Pin 2: Hot (+)
Pin 3: Cold ()
XLR Jack
LINE INPUT (monaural channels) Tip: Hot (+)
GROUP OUT, STEREO OUT, Ring: Cold ()
MONITOR OUT, AUX SEND Sleeve: Ground Ring
Tip: Output
INSERT Ring: Input
Sleeve: Ground Sleeve Tip
Tip: L
PHONES Ring: R
Sleeve: Ground TRS Phone Jack
RETURN Tip: Hot
LINE INPUT (stereo channels) Sleeve: Ground
Sleeve Tip
Phone Jack
·
MIC INPUT STEREO OUT
LINE INPUT
GROUP OUT STEREO OUT
MONITOR OUT AUX SEND
INSERT
PHONES
RETURN
LINE INPUT
10
MG206C-USB/MG206C
I CIRCUIT BOARD LAYOUT
Rear
JACK20R USB (MG206C-USB only)
PS20
JACK20F
MIX20
Front
11
MG206C-USB/MG206C
I WIRING DIAGRAM
(MG206C-USB only)
JACK20R USB PS20
CN003 CN903 CN002 CN004 CN101 CN103 CN102 CN101
(10P) (9P) (2P) (15P) (9P) (2P) (3P) (7P)
3
2
4
5
JACK20F
1
6
CN001
W501 W601 W701 W801 W001 W002 (3P)
(9P) (9P) (9P) (9P) (6P) (9P)
W101 W201 W301 W401
(9P) (9P) (9P) (9P)
CN501 CN601 CN701 CN801 CN001 CN002
(9P) (9P) (9P) (9P) (6P) (9P)
CN101 CN201 CN301 CN401
(9P) (9P) (9P) (9P) CN053
(7P)
CN004 CN003
(15P) (10P)
MIX20
Assembly Name Connection Remarks
No. Part No. Location
1 (WJ98020) Connector Assembly PS7P MIX20-CN053 <-> PS20-CN101 7P-110 40
2 (WJ98040) Connector Assembly PS3P JACK20F-CN001 <-> PS20-CN102 3P-140 50
3 (WJ98050) Connector Assembly PS2P JACK20R-CN002 <-> PS20-CN103 2P-380 60
4 (WJ78450) Connector Assembly USB20 JACK20R-CN903 <-> USB-CN101 9P-140 100 MG206C-USB only
5 (WJ78460) Connector Assembly REAR10P MIX20-CN003 <-> JACK20R-CN003 10P-700 130
6 (WJ78470) Connector Assembly REAR15P MIX20-CN004 <-> JACK20R-CN004 15P-720 140
12
MG206C-USB/MG206C
I OVERALL ASSEMBLY WIRING
The inside room of this product is very little because a lot of units are installed fully.
To prevent the panel's coming up and other things when assembling, perform the cable connection according to the followings.
Note: The components marked " * " are used only for MG206C-USB.
1. The wiring of the Inner Chassis Assembly.
1-1. Before installing the JACK20R [Ref. 120] circuit board in the inner chassis Assembly [Ref. 20], connect the following connector
assemblies to the JACK20R [Ref. 120] circuit board and bind the connector assemblies with the cord binder [Ref. 180].
Connector Assembly Name
Ref. No.
60 Connector Assembly PS2P
100 * Connector Assembly USB20
130 Connector Assembly REAR10P
140 Connector Assembly REAR15P
CN004 CN002 CN903 CN003
140 60 * 100 130
120
180
Note: Binding position
13
MG206C-USB/MG206C
1-2. Install the heatsink assembly [Ref. 30], USB assembly [* Ref. 90] and JACK20R circuit board [Ref. 120] in the inner chassis
assembly [Ref. 20].
1-3. Connect the connector assemblies according to the picture below.
CN103 CN102 CN101
* 100 * 90 30 60 50 40
120
20
Note: Twist connector assemblies three times in this section.
180 Note: Fix the connector assembly PS2P [Ref. 60], connector assembly REAR10P [Ref. 130] and connector
assembly REAR15P [Ref. 140] with the cord binder [Ref. 180].
Note: Fix the connector assembly REAR10P [Ref. 130], connector assembly REAR15P [Ref. 140], connector 180
assembly PS7P [Ref. 40] and connector assembly PS3P [Ref. 50] with the cord binder [Ref. 180].
14
MG206C-USB/MG206C
1-4. Install the inner chassis assembly [Ref. 20] on the bottom case assembly [Ref. 10].
20 10 40 50
230 Note: Fix the connector assembly REAR10P [Ref. 130] and connector assem- 130 140
bly REAR15P [Ref. 140] with the cord holder [Ref. 230].
Note: Pass the connector assembly REAR10P [Ref. 130] and connector assembly REAR15P [Ref. 140] through
the incision part of inner chassis assembly [Ref. 20]. At that time, take care the cables not to be slack-
ened.
15
MG206C-USB/MG206C
2. The wiring of the MIX20 circuit board and JACK20F circuit board.
Whole picture
250
JACK20F JACK20F
CN001 K101
50
40
MIX20
MIX20 MIX20 MIX20 MIX20 CN001 MIX20
MIX20 MIX20 MIX20 MIX20 CN501 CN601 CN701 CN801 CN053
CN101 CN201 CN301 CN401 MIX20
CN002
MIX20
MIX20 K051
K052
140 130
340 MIX20 MIX20
CN004 CN003
16
MG206C-USB/MG206C
2-1. Connect the connector assemblies from the inner chassis assembly.
Final Assembly Connector Assembly Name
Wiring Point
Location
Ref. 40 Connector Assembly PS7P MIX20 circuit board CN053
Ref. 50 Connector Assembly PS3P JACK20F circuit board CN001
Ref. 130 Connector Assembly REAR10P MIX20 circuit board CN003
Ref. 140 Connector Assembly REAR15P MIX20 circuit board CN004
Macro picture around CN053 on the MIX20 circuit board.
250
50
JACK20F
CN001
340
40
MIX20
CN053
JACK20F
K101
Note: Fix the connector assembly PS7P [Ref. 40] and connector assembly
[Ref. 50] with the cord holder.
Note: Pass the connector assembly PS7P [Ref. 40] and connector assembly PS3P [Ref. 50] through the inci-
sion part of JACK20F circuit board [Ref. 250].
17
MG206C-USB/MG206C
Macro picture around the CN003 of MIX20 circuit board.
Note: Pass the connector assembly REAR10P [Ref. 130] and connector as-
sembly REAR15P [Ref. 140] through the incision part of MIX20 circuit
board [Ref. 340].
340
130
MIX20
CN004
MIX20
CN003
140
MIX20 MIX20
K052 K051
Note: Fix the connector assembly REAR15P [Ref. Note: Fix the connector assembly REAR10P [Ref. 130] with
140] with the cord holder. the cord holder.
2-2. Connect the ten (10) jumper wires of JACK20F circuit board to the MIX20 circuit board.
Note: Bend the jumper wires according to the picture below.
Note: After bend, press the jumper wires so that their height from the MIX20 circuit board's component side become 15 mm or less.
18
MG206C-USB/MG206C
I DISASSEMBLY PROCEDURES
1. Top Cover (Time required: 15 min.)
1-1 Remove the sixteen (16) fader knobs marked [490], two
(2) fader knobs marked [500] and fader knob marked
[510]. (Fig. 1)
1-2 Remove the fifteen (15) screws marked [400], twenty-
one (21) screws marked [410], three (3) screws marked
[420], six (6) screws marked [430], thirty-seven (37) hex-
agonal nuts and thirty-seven (37) washers. (Fig. 1)
1-3 The top cover can then be removed. (Fig. 1)
* When installing the top cover on the bottom case
assembly, tighten the screws in the order shown in
Fig. 1. (Fig. 1)
[430]
Top cover
[400] [410]
M9 Hexagon nut and washer
[420]
[400]
[400] Screw tighten (3rd)
Top cover
[400] Screw tighten (1st)
[400]
[400] Screw tighten (2nd)
[400] [400]
[490] [500] [510]
[400]: Bind Head Tapping Screw-B 3x8 MFZN2B3 (WE774400)
[410]: Bind Head Tapping Screw-B 3x8 MFZN2B3 (WE774400)
[420]: Bind Head Screw 3x6 MFZN2B3 (WE878300)
[430]: Bind Head Tapping Screw-B 3x8 MFZN2B3 (WE774400)
[490]: Fader Knob Black/L-Gray (V9664900)
[500]: Fader Knob Red/D-Gray (V9665000)
[510]: Fader Knob White/Red (V9665100)
(Fig. 1)
19
MG206C-USB/MG206C
2. MIX20 Circuit Board and JACK20F Circuit
Board (Time required: 20 min.)
2-1 Remove the top cover. (See procedure 1.)
2-2 Disconnect the fourteen (14) connectors. (Fig. 2)
2-3 Remove the fourteen (14) screws marked [350]. (Fig. 2)
2-4 Release the eight (8) hooks and remove the MIX20 cir-
cuit board. (Fig. 2)
2-5 Remove the three (3) screws marked [300] and remove
the JACK20F circuit board. (Fig. 2)
* The buttons, knobs, knob black (WD942200), but-
ton on assembly (WH455200) are not components
of the MIX20 circuit board. When replacing the MIX20
circuit board, remove these components from the
old circuit board and install them on the new circuit
board.
[300]
JACK20F
[350]
Hook
Hook
Priority Screw [350] MIX20
[350]
Hook
Hook
[350]
Hook
[350]
[300]: Bind Head Tapping Screw-B 3x8 MFZN2W3 (WE774300)
[350]: Bind Head Tapping Screw-B 3x8 MFZN2W3 (WE774300)
(Fig. 2)
20
MG206C-USB/MG206C
3. JACK20R Circuit Board
(Time required: 25 min.)
3-1 Remove the top cover. (See procedure 1.)
3-2 Remove the MIX20 circuit board and JACK20F circuit
board. (See procedure 2.)
3-3 Remove the two (2) screws marked [170A] and remove
the rear JK shield. (Fig. 3)
3-4 Remove the screw marked [150], twelve (12) hexago-
nal nuts and twelve (12) washers. (Fig. 3)
The JACK20R circuit board can then be removed. (Fig. 3)
[170A]
[170B] Shield PS Rear JK shield
Priority Screw
JACK20R
M9 Hexagon nut and washer [150]
M9 Hexagon nut and washer
[150]: Bind Head Tapping Screw-B 3x8 MFZN2B3 (WE774400)
[170A]: PW Head Tapping Screw-B 3x8 MFZN2W3 (WF002600)
[170B]: PW Head Tapping Screw-B 3x8 MFZN2W3 (WF002600)
(Fig. 3)
4. PS20 Circuit Board (Time required: 25 min.)
4-1 Remove the top cover. (See procedure 1.)
4-2 Remove the MIX20 circuit board and JACK20F circuit
board. (See procedure 2.)
4-3 Remove the two (2) screws marked [170A] and remove
the rear JK shield. (Fig. 3)
4-4 Remove the screw marked [170B] and remove the shield
PS. (Fig. 3)
21
MG206C-USB/MG206C
4-5 Remove the three (3) screws marked [190], three (3)
screws marked [200] and three (3) screws marked [220].
(Fig. 4)
The inner chassis with heatsink assembly, JACK20R
circuit board and USB assembly (MG206C-USB only)
can be removed. (Fig. 4)
4-6 Disconnect the three (3) connectors. (Fig. 4)
4-7 Remove the four (4) screws marked [80] and screw marked
[70]. Then remove the heatsink assembly. (Fig. 5)
4-8 Remove the three (3) screws marked [40] and five (5)
screws marked [50], and separate the PS20 circuit board
from the heatsink. (Fig. 5)
[220]
Heatsink assembly
[50]
[40]
[50] [40]
Heatsink
[200] [200] 25
Inner chassis with heatsink assembly, JACK20R circuit boad
and USB assembly (MG206C-USB only)
[70]
[190] [190] [190]
Priority Screw
Priority Screw
[80] [80]
[190]: Bind Head Tapping Screw-B 3x8 MFZN2B3 (WE774400)
[200]: Bind Head Tapping Screw-B 3x8 MFZN2W3 (WE774300) [40]: Bind Head Tapping Screw-B 3x8 MFZN2W3 (WE774300)
[220]: PW Head Tapping Screw-B 3x8 MFZN2W3 (WF002600) [50]: Bind Head Tapping Screw-B 3x8 MFZN2W3 (WE774300)
[70]: Bind Head Tapping Screw-B 3x8 MFZN2B3 (WE774400)
(Fig. 4)
[80]: Bind Head Tapping Screw-B 3x8 MFZN2W3 (WE774300)
(Fig. 5)
22
MG206C-USB/MG206C
5. USB Circuit Board (MG206C-USB only)
(Time required: 20 min.)
5-1 Remove the top cover. (See procedure 1.)
5-2 Remove the MIX20 circuit board and JACK20F circuit
board. (See procedure 2.)
5-3 Remove the two (2) screws marked [170A] and remove
the rear JK shield. (Fig. 6)
5-4 Remove the two (2) screws marked [110] and remove
the USB assembly. (Fig. 6)
5-5 Unsolder the shield USB mounting solder (2 locations)
and separate the shield USB from the USB circuit board.
(Fig. 6)
* The shield USB is not a component of the USB cir-
cuit board. When replacing the USB circuit board,
remove the shield USB from the old circuit board
and install it on the new circuit board.
[170A] Shield USB
Rear JK shield
Solder
75*
USB assembly
Priority Screw
[110]
[110]
[110]: Bind Head Tapping Screw-B 3x8 MFZN2B3 (WE774400)
[170A]: PW Head Tapping Screw-B 3x8 MFZN2W3 (WF002600)
(Fig. 6)
23
MG206C-USB/MG206C
I LSI PIN DESCRIPTION
· PCM2900E/2K (X7143A00) USB PROTOCOL CONTROLLER USB: IC101
PIN PIN
NAME I/O FUNCTION NAME I/O FUNCTION
No. No.
1 D+ I/O USB differential input/output plus 15 VOUTR O DAC analog output for R-channel
2 D- I/O USB differential input/output minus 16 VOUTL O DAC analog output for L-channel
3 VBUS - Connect to USB power (VBUS) 17 VCCP1I - Internal analog power supply for PLL
4 DGNDU - Digital ground for USB transceiver 18 AGNDP - Analog ground for PLL
5 HID0 I HID key state input(mute), active high 19 VCCP2I - Internal analog power supply for PLL
6 HID1 I HID key state input(volume up),active high 20 XTO O Crystal oscillator output
7 HID2 I HID key state input(volume down),active high 21 XTI I Crystal oscillator input
8 SEL0 I Must be set to high 22 AGNDX - Analog ground for oscillator
9 SEL1 I Must be set to high 23 VCCXI - Internal analog power supply for oscillator
10 VCCCI - Internal analog power supply for codec 24 TEST0 I Test pin, must be connected to GND
11 AGNDC - Analog ground for codec 25 TEST1 O Test pin, must be left open
12 VINL I ADC analog input for L-channel 26 DGND - Digital gronud
13 VINR I ADC analog input for R-channel 27 VDDI - Internal digital power supply
14 VCOM - Common for ADC/DAC(VCCCI/2) 28 SSPND O Suspend flag, active low
(Low: suspend, High: operational)
I IC BLOCK DIAGRAM
· NJM2068M-D (TE2) (X3505A00) · KIA7812API (X4153A00)
Dual Operational Amplifier Regulator +12V
JACK20: IC702, 752, 802, 852 PS20: IC105
MIX20: IC001, 003, 901, 902, 951, 952, ICM01
USB: IC103, 104 1 INPUT
R22 R17 R23
R1 Q11 Q11-1
Output A 1 +V 8
+DC Voltage Q15
Supply
Q16
Inverting
2 7 Output B Q12
Input A - +
Q14 R14
Non-Inverting Inverting R10 R15
3 6 Q19
Input A + - Input B Q17 R16
R19
-DC Voltage Supply 4 -V 5 Non-Inverting R12 3 OUTPUT
Input B R20
Q18 Q6
Q1
R18
R11 R9
Z1 R7 C1
R2 Q10
Q2
Q7 R21
Q13 R3
Q4
Q3 Q5 Q9 Q8
R13
R4 R5 R6 R8
2 COMMON (GND)
· NJM072BM-E (TE1) (X4543A00)
Dual Operational Amplifier
JACK20: IC101, 201, 301, 401, 501, 601
V+
-INPUT
OUTPUT
+INPUT
V-
24
MG206C-USB/MG206C
· KIA7805API/P (X4928A00) · KIA7815API (X4930A00)
Regulator +5V Regulator +15V
PS20: IC107 PS20: IC101, 103
1 INPUT 1 INPUT
R22 R17 R23 R22 R17 R23
R1 Q11 Q11-1 R1 Q11 Q11-1
Q15 Q15
Q16 Q16
Q12 Q12
Q14 R14 Q14 R14
R10 R15 R10 R15
Q17 Q19 R16 Q17 Q19 R16
R19 R19
R12 3 OUTPUT R12 3 OUTPUT
Q18 Q6 R20 Q18 Q6 R20
Q1 Q1
R18 R18
R11 R9 R11 R9
Z1 R7 C1 Z1 R7 C1
R2 Q10 R2 Q10
Q2 Q2
Q7 R21 Q7 R21
Q13 R3 Q13 R3
Q4 Q4
Q3 Q5 Q9 Q8 Q3 Q5 Q9 Q8
R13 R13
R4 R5 R4 R5
R6 R8 R6 R8
2 COMMON (GND) 2 COMMON (GND)
· KIA7915PI (X4931A00)
Regulator -15V
PS20: IC102, 104
GND
(1)
R15 R18 R R22
21
R23
Q28 Q17 Q21 Q22
Q24
R16 R13 R12
Q23
Q19 R24
Q
29
R20
R1 Q18 Q20
Q25
Q30
R R17 R19 Q31
14
R25
Q12 Q13
Q Q
2 3
R11
Q
26-1 Q OUTPUT
R Q 27-1
26 26 Q (3)
27
R10
Q7 D
4
R
0 Q
C1 14
C2
Q15
Q8 R9
Q
Q R R R6 16
Q 5 4 5
4 Q6 Q Q
9 10
R7
R3
Q11 R8
R INPUT
2
(2)
25
MG206C-USB/MG206C
· NJM4580M-D (TE2) (X5025A00) · BA10339F (X6266A00)
Dual Operational Amplifier Comparator
JACK20: IC001, 002, 701, 801 MIX20: ICM06-11
V+
8
OUT2 1 14 OUT3
OUT1 2 13 OUT4
2, 6 1, 7 OUTPUT
INPUT Vcc 3 12 GND
+INPUT
3, 5 IN1 4 + 11 +IN4
+
+IN1 5 10 IN4
IN2 6 + 9 +IN3
V
4 +
+IN2 7 8 IN3
· BA4560RF-E2 (X6897A00) · BA00CC0WFP-E2 (X7256A00)
Dual Operational Amplifier Regulator 3V to 15V
JACK20: IC102, 103, 153, 202, 203, 253, 302, 303, 353 USB: IC102
IC402, 403, 453, 502, 602, 703, 803, 901-903
MIX20: IC002, 004, 101, 102, 151, 201, 202, 251
IC301, 302, 351, 401, 402, 451, 501, 502, 551 N.C.
3
IC601, 602, 651, 701, 702, 751, 752, 801, 802
IC851, 852, 903-905, ICM03 Vref
- +