Text preview for : DIO8_SM_E.pdf part of Yamaha PM1D digital mixing system
Back to : Yamaha-PM1D mixsystem.par | Home
DIGITAL IO BOX
SERVICE MANUAL
CONTENTS REVISED PAGE LIST ··························································· 2-1 SPECIFICATIONS································································· 3-1 PANEL LAYOUT···································································· 3-2 DIMENSIONS ········································································ 3-3 BLOCK DIAGRAM ···································································· 4 DISASSEMBLY PROCEDURE················································· 5 LSI PIN DESCRIPTION ···························································· 8 IC BLOCK DIAGRAM ····························································· 12 CIRCUIT BOARDS ································································· 14 INSPECTION ·········································································· 19 TEST PROGRAM ··································································· 21 PARTS LIST CIRCUIT DIAGRAM
PA
011510
HAMAMATSU, JAPAN
0.27K-
200004**-350000
****
Printed in Japan '00.09
DIO8
REVISED PAGE LIST
ITEM SPECIFICATIONS PANEL LAYOUT DIMENSIONS INSPECTION TEST PROGRAM PAGE 3-1 3-2 3-3 19~20 21~28
ITEM OVERALL ASSEMBLY DC ASSEMBLY FRONT PANEL ASSEMBLY ELECTRICAL PARTS PAGE 3 5 6 7~11
2-1
DIO8 IMPORTANT NOTICE
This manual has been provided for the use of authorized Yamaha Retailers and their service personnel. It has been assumed that basic service procedures inherent to the industry, and more specifically Yamaha Products, are already known and understood by the users, and have therefore not been restated.
WARNING:
Failure to follow appropriate service and safety procedures when servicing this product may result in personal injury, destruction of expensive components and failure of the product to perform as specified. For these reasons, we advise all Yamaha product owners that all service required should be performed by an authorized Yamaha Retailer or the appointed service representative. This presentation or sale of this manual to any individual or firm does not constitute authorization, certification, recognition of any applicable technical capabilities, or establish a principal-agent relationship of any form.
IMPORTANT:
The data provided is belived to be accurate and applicable to the unit(s) indicated on the cover. The research engineering, and service departments of Yamaha are continually striving to improve Yamaha products. Modifications are, therefore, inevitable and changes in specification are subject to change without notice or obligation to retrofit. Should any discrepancy appear to exist, please contact the distributor's Service Division.
WARNING: IMPORTANT:
Static discharges can destroy expensive components. Discharge any static electricity your body may have accumulated by grounding yourself to the ground bus in the unit (heavy gauge black wires connect to this bus). Turn the unit OFF during disassembly and parts replacement. Recheck all work before you apply power to the unit.
WARNING: CHEMICAL CONTENT NOTICE!
The solder used in the production of this product contains LEAD. In addition, other electrical/electronic and/or plastic (where applicable) components may also contain traces of chemicals found by the California Health and Welfare Agency (and possibly other entities) to cause cancer and/or birth defects or other reproductive harm. DO NOT PLACE SOLDER, ELECTRICAL/ELECTRONIC OR PLASTIC COMPONENTS IN YOUR MOUTH FOR ANY REASON WHAT SO EVER! Avoid prolonged, unprotected contact between solder and your skin! When soldering, do not inhale solder fumes or expose eyes to solder/flux vapor! If you come in contact with solder or components located inside the enclosure of this product, wash your hands before handling food.
IMPORTANT NOTICE FOR THE UNITED KINGDOM
Connecting the Plug and Cord
IMPORTANT.
The wires in this main lead are coloured in accordance with the following code: BLUE: NEUTRAL BROWN: LIVE
As the colours of the wires in the main lead of this apparatus may not correspond with the coloured markings identifying the terminals in your plug, proceed as follows: The BLUE wire must be connected to the terminal that is marked with the letter N (or coloured BLACK). The BROWN wire must be connected to the terminal that is marked with the letter L (or coloured RED). Be certain that neither core is connected to the earth terminal of the three pin plug.
WARNING
Components having special characteristics are marked originally installed. and must be replaced with parts having specification equal to those
2-2
DIO8
SPECIFICATIONS
Sampling frequency (external sync) Power supply Others: 230 V, 50 Hz Power consumption Dimensions (W x H x D) Weight Operating temperature Power cable length Accessories 70 W 480 mm x 185.5 mm x 411.6 mm 15.5 kg 10 35 °C 1.5 m Connection cable (68-pin, D-sub, half-pitch) x 2, Length: 3 m 39.69 kHz 50.88 kHz USA and Canada: 120 V, 60 Hz
I/Os
I/O connectors INPUT A, B OUTPUT A, B COM WORD CLOCK IN WORD CLOCK OUT (X4) *1: On the rear panel RS422 RS422 RS232C TTL/75 (ON/OFF) *1 TTL/75 Level Type D-sub, half-pitch, 68-pin connector (female) D-sub, half-pitch, 68-pin connector (female) D-sub,9-pin connector (male) BNC connector BNC connector
Slots
Eight slots (slots 1-8) are available on the DIO8 for installing digital I/O cards and analog I/O cards. Slot 1 supports a serial interface card (not released yet).
Card MY8-TD MY8-AT MY8-AE MY8-AD MY4-AD MY4-DA Format TASCAM ADAT AES/EBU ANALOG IN ANALOG IN ANALOG OUT 8 IN 8 IN 8 IN 8 IN 4 IN -- Input 8 OUT 8 OUT 8 OUT -- -- 4 OUT Output
3-1
DIO8
PANEL LAYOUT
Front Panel
I/O UNIT ID
1
PORT B SELECTOR 5-8
1-4
I/O UNIT ID PORT B SELECTOR 5-8
2
1-4
POWER ON/ OFF
POWER ON/ OFF
3
DIGITAL IO BOX
1 I/O UNIT ID indicator 2 PORT B SELECTOR switch 3 POWER ON/OFF switch
Rear Panel
IN
4
75
OFF ON WORD CLOCK
8
7
6
5
4
3
2
1
IN
OFF ON WORD CLOCK
COM
75
OUT
OUT
COM
B (14/58)
5
OUTPUT
A (14/18)
B (14/58)
INPUT
A (14/18)
6
* The illustration shows the unit without any cards installed.
B (14/58)
OUTPUT
A (14)/(18)
B (14/58)
INPUT
A (14)/(18)
7
8
4 WORD CLOCK IN jack, ON/OFF switch 5 WORD CLOCK OUT jacks 6 COM port 7 OUTPUT connectors A (1-4)/(1-8), B (1-4/5-8) 8 INPUT connectors A (1-4)/(1-8), B (1-4/5-8)
3-2
DIO8
DIMENSIONS
480
I/O UNIT ID
411.6 185.5 176
PORT B SELECTOR 5-8
1-4
POWER ON/ OFF
400
Unit: mm 9.5
3-3
Reg. control, Card ID
MUTE Serial (DIO_SLOT1)
Slave LOCK
2ch 2ch 2ch 2ch 2ch 2ch
4 4 4 4 IC201 4 4
Master CLOCK
Slave_LOCK
Parallel bus
Reg. control, Card ID
MUTE
Slave LOCK
2ch 2ch Master CLOCK 4 2ch 2ch 2ch 2ch
4 4 4 4 IC202 4 4
Master CLOCK
Slave_LOCK
CON1 : : CON8
CS1 : : CS8
Address Decoder
Reg.
Slave_LOCK
SLOT_WC[8] : : SLOT_WC[1]
4
DIO8
CN
2ch 4
BLOCK DIAGRAM
IC307-310
SLOT 1
DSP5 #1
2ch or 4ch
16 DIO I/F ATSC 4
UNLOCK MUTE
2ch or 4ch
16
Driver/ Recerver
Audio IN WC IN WC OUT Tx, Rx RTS, DTR
2ch or 4ch
16
INPUT A
ID IN ID OUT MSB. 2CH IN
DIR2
IC108
MUTE
IC301-306
Master CLOCK 4
2ch or 4ch
16
Driver/ Recerver
Audio OUT WC IN WC OUT
2ch or 4ch
16
SLOT 4
2ch
MUTE
4
Tx, Rx RTS, DTR
OUTPUT A
ID IN ID OUT MSB. 2CH OUT
IC501-506 IC607-610 DIO I/F ATSC 4
UNLOCK MUTE
Master CLOCK 2ch 4
SLOT 5
DSP5 #2
2ch or 4ch 16
2 or 4ch 16
Driver/ Recerver
Audio IN WC IN WC OUT Tx, Rx RTS, DTR
2ch or 4ch
16
INPUT B
ID IN ID OUT MSB. 2CH IN
DIR2
IC115
MUTE
IC601-606
2ch or 4ch
16
Driver/ Recerver
Audio OUT WC IN WC OUT
2ch or 4ch
16
SLOT 8
2ch
MUTE
4 Master CLOCK IC101 INT
48k 44.1K
Tx, Rx RTS, DTR
OUTPUT B
ID IN ID OUT MSB. 2CH OUT
IC801-806
Master CLOCK
FPGA MUTE
UNLOCK SOFT POW. OFF
IC104
DIR2 2 IC106, 110
WC SEL & HDLT SEL SEL
SLOT_WC[1-8]
Reg.
DATA_bus ADDRESS_bus
Master_LOCK Master_WC
8
Slave_WC
FRGA
IC104
Receiver
IC1
75 Master_WC
WC IN
CPU
IC9
SCI (Tx_Rx)
WC
WC OUT 4
Driver
IC2, 3
SCI (DIO_SLOT1/COM)
FPGA IC104
Serial (DIO_SLOT1)
LED3
UNIT No.
DIO_SLOT1 /COM SEL.
Serial (COM)
ROM
RAM
IC13, 14
FLASH
Driver/ Receiver
IC2
IC18
SCI SEL. SW
Slave_LOCK
DIR2
IC109
COM PORT B SEL. SW
MAIN
KEC-92496
DIO8
DISASSEMBLY PROCEDURE
1.
1-1
Top Cover
Remove the sixteen screws (16) marked [430]. The top cover can then be removed. (Fig. 1)
2.
Circuit Boards and Unit
Remove the top cover, each circuit board and unit can then be removed. (Fig. 2)
Circuit Board and Unit DC Assembly Power Transformer WC Ref. No. 350 370 220 Screw Bind Head Tapping Screw-B A4.0x6 MFZN2BL (VC688800) Bind Head Tapping Screw-B A4.0x6 MFZN2BL (VC688800) Flat Head Screw 3.0x6 MFZN2BL (VS863000) QTY 4 4 5
DC assembly
WC
[350]
[350]
[370] [370]
[430] x 16 Top panel
Power transformer [220]
[430]: Bind Head Tapping Screw-B A4.0x8 MFZN2BL (VC688800)
Fig. 1
Fig. 2
[220]
3.
3-1 3-2 3-3 3-4
DC Circuit Board
Remove the DC assembly. (See Procedure 2.) Remove the four (4) screws marked [80]. The transistor holder 1 can then be removed. (Fig. 3) Remove the five (5) screws marked [100]. The transistor holder 2 can then be removed. (Fig. 3) Remove the three (3) screws marked [50] and the two (2) screws marked [60]. The DC circuit board can then be removed. (Fig. 3)
4.
* 4-1 4-2
CN Circuit Board
Note that remove all cards before following operation. Remove the top cover. (See Procedure 1.) Remove the eight (8) screws marked [330]. The angle bracket can then be removed. (Fig. 4)
5
DIO8
4-3 4-4
Remove the two (2) screws marked [310]. The CN support can then be removed. (Fig. 4) Remove the six (6) screws marked [290]. The CN circuit board can then be removed. (Fig. 4)
· DC Assembly
[330]
Angle bracket
[330] [100] [310] [310] Transistor holder1
Transistor holder2
DC
[80]
[50]
CN
[290]
[60] CN support [50]: Bind Head Screw A4.0x8 MFZN2BL (VP156800) [60]: Bind Head Tapping Screw-B 3.0x8 MFZN2BL (EP600190) [80]: Pan Head Screw SP 4.0x8 MFZN2Y (EL200020) [100]: Pan Head Screw SP 4.0x8 MFZN2Y (EL200020) Fig. 3
[290]: Bind Head Tapping Screw-B 3.0x6 MFZN2BL (EP600230) [310]: Bonding Tapping Screw-B 3.0x8 MFZN2BL (VN413300) [330]: Bonding Tapping Screw-B 3.0x8 MFZN2BL (VN413300) Fig. 4
5.
5-1 5-2 5-3 5-4 5-5 5-6
MAIN Circuit Board
Remove the top cover. (See Procedure 1.) Remove the CN circuit board. (See Procedure 4.) Remove the sixteen screws (16) marked [450]. The IF plate can then be removed. (Fig. 5) Remove the seven (7) screws marked [260]. The OPT support can then be removed. (Fig. 5) Remove the three (3) screws marked [150]. (Fig. 5) Remove the eight (8) screws marked [A] and the two (2) screws marked [B]. The MAIN circuit board can then be removed. (Fig. 5)
6
DIO8
IF plate [260] OPT support 2
[150] OPT support 2
MAIN
[260]
[450] x 16
[B]
[A]
[A]
[A]
[A]
OPT support 1
[150]: Bind Head Tapping Screw-B 3.0x6 MFZN2BL (EP600230) [260]: Bind Head Tapping Screw-B A4.0x8 MFZN2BL (VC688800) [450]: Bind Head Screw A4.0x12 MFZN2BL (VP156900) Fig. 5
6.
6-1 6-2
Front Panel Assembly
Remove the eight (8) screws marked [410]. The rack mount angle can then be removed. (Fig. 6) Remove the three (3) screws marked [390]. The front panel assembly can then be removed. (Fig. 6)
7.
7-1 7-2 7-3 7-4
LED3 Circuit Board, AC Circuit Board
Remove the front panel assembly. (See Procedure 6.) Remove th five (5) screws marked [100]. The front panel can then be removed. (Fig. 7) Remove the two (2) screws marked [60]. The LED3 circuit board can then be removed. (Fig. 7) Remove the four (4) screws marked [80]. The AC circuit board can then be removed. (Fig. 7)
· Front Panel Assembly
AC
[410] [410]
Rack mount angle
Rack mount angle
Front panel assembly [100] Front panel [100] [60] [80] x 4
LED3
[390] [390]: Oval Head Screw 4.0x8 MFZN2BL (VS153600) [410]: Oval Head Screw 4.0x8 MFZN2BL (VS153600) Fig. 6
[60]: Bind Head Tapping Screw-B 3.0x6 MFZN2BL (EP600230) [80]: Bind Head Tapping Screw-B A4.0x8 MFZN2BL (VC688800) [100]: Oval Head Screw 4.0x8 MFZN2BL (VS153600) Fig. 7
7
DIO8
LSI PIN DESCRIPTION
HD6437042AF53F (XY721A00) CPU
PIN NO. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 NAME PE14 PE15 VSS A0 A1 A2 A3 A4 A5 A6 A7 A8 A9 A10 A11 A12 A13 A14 A15 A16 VCC A17 VSS /RAS /CASL /CASH VSS RDWR / PB5 A18 A19 A20 PB9 /A21 VSS /RD /WDTOVF /WRH VCC /WRL VSS /CS1 /CS0
PA9 / TCLKD /IRQ2 / TCLKC
MAIN: IC009 PIN NO. 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 105 106 107 108 109 110 111 112 NAME D11 D10 D9 D8 VSS D7 D6 D5 VCC D4 D3 D2 D1 D0 VSS XTAL MD3 EXTAL MD2 NMI VCC MD1 MD0 PLLVCC PLLCAP PLLVSS PA15 / CK /RES PE0 PE1 PE2 PE3 PE4 VSS AN0 / PF0 AN1 / PF1 AN2 / PF2 AN3 / PF3 AN4 / PF4 AN5 / PF5 AVSS AN6 / PF6 AN7 / PF7 AVCC VSS PE5 VCC PE6 PE7 PE8 PE9 PE10 VSS PE11 PE12 PE13 I/O I/O I/O I/O I/O I I/O I/O I/O I I/O I/O I/O I/O I/O I I I I I I I I I I I I O I I I I I I I I I I I I I I I I I I O I O O O O O I O O O FUNCTION
I/O O O I O O O O O O O O O O O O O O O O O I O I O O O O O O O O O I O O O I O I O O O I O O I O I I O I I/O I/O I/O I I/O Port E Port E Ground
FUNCTION
Data bus Ground Data bus Power supply Data bus Ground Crystal oscillator Mode control Crystal oscillator Mode control Non-maskable interrupt request Power supply Mode control Mode control PLL Power supply PLL capacitor PLL Ground Port A / Clock Reset Port E Ground Analog input / Port F
Address bus
Power supply Address bus Ground Row address strobe Column address strobe (low) Column address strobe (high) Ground DRAM read/write / Port B Address bus Port B / Address bus Ground Read Watch dog timer overflow High write Power supply Low write Ground Chip select Chip select Port A / Timer clock Interrupt request / Timer clock Chip select Chip select Interrupt request Data transmission Data reception Interrupt request Port A / Data transmission Port A / Data reception Data bus Ground Data bus
/CS3 /CS2 /IRQ1 TXD RXD /IRQ0 PA1 / TXD0 PA0 / RXD0 D15 D14 D13 VSS D12
Analog ground Analog input / Port F Analog input / Port F Power supply Ground Port E Power supply Port E Ground Port E
8
DIO8
YM3436DK (XG948E0) DIR2 (Digital Format Interface Receiver)
PIN NO. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 NAME DAUX HDLT DOUT VFL OPT SYNC MCC WC MCB MCA SKSY XI XO P256 LOCK Vss TC DIM1 DIM0 DOM1 DOM0 KM1 I/O I O O O O O O O O O I I O O O O I I I I I FUNCTION Auxiliary input for audio data Asynchronous buffer operation flag Audio data output Parity flag output Fs x 1 Synchronous output signal for DAC Fs x 1 Synchronous output signal for DSP Fs x 64 Bit clock output FS x 1 Word clock output Fs x 128 Bit clock output Fs x 256 Bit clock output Clock synchronization control input Crystal oscillator connection or external clock input Crystal oscillator connection VCO oscillating clock connection PLL lock flag Logic section power (GND) PLL time constant switching output Data input mode selection Data input mode selection Data output mode selection Data output mode selection Clock mode switching input 1 PIN NO. 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 NAME RSTN Vdda CTLN PCO (NC) CTLP Vssa TSTN KM2 KM0 FS1 FS0 CSM EXTW DDIN LR Vdd ERR EMP CD0 CCK CLD I/O I I O I I I I O O I I I O O O O I I
MAIN: IC106, 108110, 115 FUNCTION
System reset input VCO section power (+5V) VCO control input N PLL phase comparison output VCO control input P VCO section power (GND) Test terminal. Open for normal use Clock mode switching input 2 Clock mode switching input 0 Channel status sampling frequency display output 1 Channel status sampling frequency display output 0 Channel status output method selection External synchronous auxiliary input word clock EIAJ (AES/EBU) data input PLL word clock output Logic section power (+5 V) Data error flag output Channel status emphasis control code output 3-wire type microcomputer interface data output 3-wire type microcomputer interface clock input 3-wire type microcomputer interface load input
9
DIO8
SGH609080F-47F (XU235A00) ATSC
PIN NO. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 NAME syncati mccti mcbti VCC GND mcati GND siat0 siat1 siat2 siat3 ati GND ato soat3 soat2 soat1 soat0 VCC GND mcato GND mcbto mccto I/O I I I FUNCTION Synch. word input terminal for ati, siat3-0 input 64 fs clock input terminal for ati, siat3-0 input 128 fs clock input terminal for ati, siat3-0 input Power supply (+5 V) Ground 256 fs clock input terminal for ati, siat3-0 input Ground Serial data input terminal Optical input terminal Ground Optical output terminal Serial data output terminal Power supply (+5 V) Ground 256 fs clock input terminal for ato, soat3-0 output Ground 128 fs clock input terminal for ato, soat3-0 output 64 fs clock input terminal for ato, soat3-0 output Synch. word input terminal for ato, soat3-0 output Clock select terminal for ato, soat 3-0 output 0: mcato,mcbto,mccto,syncato 1: mcai,mcbi,mcci,synci Format select terminal for ato, soat3-0 output Format select terminal for ato, soat3-0 output
0: mcato,mcbto,mccto,syncato 1: mcai,mcbi,mcci,synci output format ato sel1 ato sel0 ato 1 1 soat0 1 0 soat2, 0 0 1 soat3-0 0 0
MAIN: IC307310, 607610 PIN NO. 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 NAME synci mcci mcbi VCC GND mcai GND si0 si1 si2 si3 GND so3 so2 so1 so0 VCC GND mcao GND mcbo mcco synco so-sel1 so-sel0 I/O I I I FUNCTION Synch. word input terminal for si3-0 input 64 fs clock input terminal for si3-0 input 128 fs clock input terminal for si3-0 input Power supply (+5 V) Ground 256 fs clock input terminal for si3-0 input Ground I I I I O O O O I I I I I I Serial data input terminal Ground Serial data output terminal Power supply (+5 V) Ground 256 fs clock input terminal for so3-0 output Ground 128 fs clock input terminal for so3-0 output 64 fs clock input terminal for so3-0 output Synch. word input terminal for so3-0 output Format select terminal for soat3-0 output Format select terminal for soat3-0 output
so sel1 1 1 0 0 so sel0 1 0 1 0 input format not enable to set so0 so2, 0 so3-0 (8ch/line) (4ch/line) (2ch/line)
I I I I I I O O O O O I I I I I
I
25 syncato 26 clksel
66
uo3
O
27 ato-sel0 28 ato-sel1
I I
67
uo2
O U-bit output terminal for optical output
68
(8ch/line) (4ch/line) (2ch/line)
uo1
O
29 bitsel2 30 bitsel1 31 bitsel0 VCC 32 GND 33 34 ext-sync2 35 ui0 36 ui1 37 ui2 38 ui3 39 si-sel0 40 si-sel1
Bit shift select terminal for the ato output Power supply (+5 V) Ground Synch. detect output terminal 2 U-bit input terminal for optical output input format select terminal for si3-0 input format select terminal for si3-0i
si sel1 1 1 0 0 si sel0 1 0 1 0 input format not enable to set si0 si2, 0 si3-0 (8ch/line) (4ch/line) (2ch/line)
uo0 69 70 ext-sync1 VCC 71 GND 72 clk 73 GND 74 /res 75 GND 76 77 wc-at mute 78 79 ati-sel1 80 ati-sel0
O O I I O I I I
Synch. detect output terminal 1 Power supply (+5 V) Ground Clock input terminal for word clock extract Ground System reset input terminal Ground Word clock output terminal Data mute input terminal Input format select terminal for ati, siat3-0. input format select terminal for ati, siat3-0.
ati sel1 1 1 0 0 ati sel0 1 0 1 0 input format ati ati0 ati2, 0 ati3-0 (8ch/line) (4ch/line) (2ch/line)
10
DIO8
YSS904-F (XV989A00) DSP5 (Digital Signal Processor)
PIN NO. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 NAME NC NC NC NC Vdd Vss XI XO Vdd /SYNCI /SYNCO Vdd CKI CKO CKSEL Vss MCKD /SSYNC /IC /TEST NC NC NC Vdd Vss /CS /WR /RD CA7 CA6 CA5 CA4 CA3 CA2 CA1 Vss Vdd CD15 CD14 CD13 CD12 CD11 CD10 CD09 CD08 CD07 CD06 Vss NC NC NC NC NC NC NC NC Vdd Vdd CD05 CD04 CD03 CD02 CD01 CD00 /WAIT Vss SIO00 SIO01 SIO02 SIO03 SIO04 SIO05 SIO06 SIO07 Vss Vdd SIO08 SIO09 SIO10 SIO11 SIO12 SIO13 SIO14 SIO15 Vss Vdd SIO16 SIO17 SIO18 SIO19 SIO20 SIO21 SIO22 SIO23 Vss Vdd SIO24 SIO25 SIO26 SIO27 NC NC NC NC I/O FUNCTION Not used Ground Power supply System master clock input (60 MHz or 30 MHz) System master clock output (High or 30 MHz) Ground Sync. signal input Sync. signal output Ground System clock input (30 MHz) System clock output (30 MHz) System master clock select Power supply Serial clock input (256 fs) Serial. signal input Initial clear Test mode setting (0: TEST, 1: Normal) Not used Ground Power supply Chip select Write enable input Read enable input PIN NO. 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 128 129 130 131 132 133 134 135 136 137 138 139 140 141 142 143 144 145 146 147 148 149 150 151 152 153 154 155 156 157 158 159 160 161 162 163 164 165 166 167 168 169 170 171 172 173 174 175 176 177 178 179 180 181 182 183 184 185 186 187 188 189 190 191 192 193 194 195 196 197 198 199 200 201 202 203 204 205 206 207 208 NAME NC NC NC NC SIO28 SIO29 SIO30 SIO31 Vss Vdd SIO32 SIO33 SIO34 SIO35 SIO36 SIO37 SIO38 SIO39 Vss Vdd SIO40 SIO41 SIO42 SIO43 SIO44 SIO45 SIO46 SIO47 Vss SIO48 SIO49 SIO50 SIO51 SIO52 SIO53 SIO54 SIO55 Vss Vdd Vdd SIO56 SIO57 SIO58 SIO59 SIO60 SIO61 SIO62 SIO63 NC NC NC NC NC NC NC NC Vss /POE Vss PIO00 PIO01 PIO02 PIO03 PIO04 PIO05 PIO06 PIO07 Vss Vdd Vdd PIO08 PIO09 PIO10 PIO11 PIO12 PIO13 PIO14 PIO15 Vss NC PIO16 PIO17 PIO18 PIO19 PIO20 PIO21 PIO22 PIO23 Vss Vdd Vdd PIO24 PIO25 PIO26 PIO27 PIO28 PIO29 PIO30 PIO31 Vss NC NC NC NC I/O FUNCTION Not used I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O
MAIN: IC201, 202
I O O I O I O I I I I I
Serial data bus Power supply Ground
Serial data bus
Power supply Ground
Serial data bus
I I I I I I I I I I I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O
Power supply
CPU address bus
Serial data bus
Power supply Ground
Power supply Ground I/O I/O I/O I/O I/O I/O I/O I/O
CPU data bus
Serial data bus
Power supply
Not used
Not used
Ground I/O I/O I/O I/O I/O I/O O I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O
I I/O I/O I/O I/O I/O I/O I/O I/O
Power supply Parallel data bus controll signal Power supply
CPU data bus
Parallel data bus
Wait output Power supply
Power supply Ground I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O
Serial data bus
Power supply Ground
Parallel data bus
Serial data bus
Power supply Not used
Power supply Ground
Parallel data bus
Power supply Ground I/O I/O I/O I/O I/O I/O I/O I/O
Serial data bus
Power supply Ground Serial data bus
Parallel data bus
Power supply Not used
Not used
11
DIO8
IC BLOCK DIAGRAM
HD74LV00AFPEL (IS000000) Quad 2 Input NAND
MAIN: IC118
HD74LVU04AFPEL (XY102A00) Hex Inverter
MAIN: IC101
HD74LV04AFPEL (IS000400) Hex Inverter
MAIN: IC107
1A 1B 1Y 2A 2B 2Y VSS
1 2 3
14 13 12
VDD 4B
1A 1Y
1 2 3 4 5 6 7
14 13 12 11 10 9 8
VDD 6A 6Y 5A 5Y 4A 4Y
1A 1Y 2A 2Y 3A 3Y Vss
1 2 3 4 5 6 7
14 13 12 11 10 9 8
VDD 6A 6Y 5A 5Y 4A 4Y
4A 2A 4Y 3B 3A 3Y
4 5 6 7
11 10 9 8
2Y 3A 3Y Vss
HD74LV08AFPEL (IS000800) Quad 2 Input AND
MAIN: IC8, 119
HD74LV32AFPEL (IS003200) Quad 2 Input OR
MAIN: IC16, 17
SN74LV138ANSR (IS013810) 3 to 8 Demultiplexer
MAIN: IC10, 11
1A 1B 1Y 2A 2B 2Y VSS
1 2 3
14 13 12
VDD 4B 4A 4Y 3B 3A 3Y
1A 1B 1Y 2A 2B 2Y GND
1 2 3
14 13 12
Vcc 4B 4A 4Y 3B 3A 3Y Output Enable Select
A B C G2A G2B G1 Y7 GND
1 A 2 3 4 5 6 7 8 B C Y0 Y1
16 15 14 13 12 11 10 9
Vcc YO Y1 Y2 Output Y3 Y4 Y5 Y6
4 5 6 7
11 10 9 8
4 5 6 7
11 10 9 8
G2A Y2 G2B Y3 G1 Y7 Y4 Y5 Y6
SN74LV139ANSR (IS013910) Dual 2 to 4 Demultiplexer
MAIN: IC24
HD74LV245AFPEL (IS024500) Octal 3-State Bus Transceiver
MAIN: IC1, 3-6, 19-22, 30-35, 103, 112-114, 203,210
TC74HC245AF (XS720A00) Octal 3-State Bus Transceiver
MAIN: IC25-29
1G 1A 1B 1Y0 1Y1 1Y2 1Y3 GND
1 2 3 4 5 6 7 8 G A B Y0 Y1 Y2 Y3 G A B Y0 Y1 Y2 Y3
16 15 14 13 12 11 10 9
Vcc 2G 2A 2B 2Y0 2Y1 2Y2 2Y3
D1R A1 A2 A3 A4 A5 A6 A7 A8 GND
1 2
20 19 18
Vcc G B1 B2 B3 B4 B5 B6 B7 B8
D1R A1 A2 A3 A4 A5 A6 A7 A8 GND
1 2
20 19 18
Vcc G B1 B2 B3 B4 B5 B6 B7 B8
3 4 5 6 7 8 9 10
3 4 5 6 7 8 9 10
17 16 15 14 13 12 11
17 16 15 14 13 12 11
12
DIO8
HD74LV273AFPEL (IS027300) Octal D-Type Flir Flop
MAIN: IC7, 15
SN75C1168NSR (XU073A00) Line Driver / Receiver
MAIN: IC2
SN75124NS (XN976A00) Triple Line Receiver
WC: IC1
CLEAR 1Q 1D 2D 2Q 3Q 3D 4D 4Q GND
1 2 3 4 5 6 7 8 9 10
20 19 18 17 16 15 14 13 12 11
VCC 8Q 8D 7D 7Q 6Q 6D 5D 5Q CLOCK
1B 1A 1R 1DE 2R 2A 2B GND
1 2 3 4 5 6 7 8
16 15 14 13 12 11 10 9
Vcc 1D 1Y 1Z 2DE 2Z 2Y 2D
1A 1B 2R 2S 2A 2B 2Y GND
1 2
16 15
Vcc 1S 1R 1Y 3A 3S 3R 3Y
Q CL D CK D CK CL Q Q CL D CK D CK CL Q
Q CL CK D CK D CL Q Q CL CK D CK D CL Q
3 4 5
14 13 12
6 7 8
11 10 9
SN75121NSR (XU816A00) Dual Line Driver
WC: IC2, 3
AM26LS31CNSR (XU996A00) Quad Line Driver
MAIN: IC301, 501-505, 601, 801-805
1A 1Y
1 2 3 4 5 6 7 8 16 15 14 13 12 11 10 9
DS26C32ATMX (XU815A00) Quad Differential Line Receiver
MAIN: IC302-306, 506, 602-606, 806
Vcc 4A 4Y 4Z ENABLE G 3Z 3Y 3A OUTPUTS Y Z H L L H H L L H Z Z INPUT A INPUT A OUTPUT A ENABLE OUTPUT C INPUT C INPUT C
1 2 3 4 5 6 7 8
1A 1B 1C 1D 1E 1F 1Y GND
1 2 3 4 5 6 7 8
16 15 14 13 12 11 10 9
Vcc 2F 2E 2D 2C 2B 2A 2Y
1Z ENABLE G 2Z 2Y 2A GND INPUT A H L H L X
+ + +
16 15 14 13 12 11 10 9
Vcc INPUT B INPUT B OUTPUT B ENABLE OUTPUT D INPUT D INPUT D
+ -
ENABLES G G H X H X X L X L L H
GND
H= high level L= low level
X= irrelevant Z= high impedance (off)
CIRCUIT BOARDS CONTENTS
AC Circuit Board (XW293B0)····················································································· 18 CN Circuit Board (XW283B0)····················································································· 17 DC Circuit Board (XW282A0)····················································································· 16 LED3 Circuit Board (XW286B0)················································································· 18 MAIN Circuit Board (XW293B0)················································································· 14 WC Circuit Board (XW293B0) ···················································································· 18 Note: See parts list for details of circuit board component parts.
13
INPUT A
INPUT B
OUTPUT A
OUTPUT B
COM
CIRCUIT BOARDS
MAIN Circuit Board
to WC-CN001
from DC-CN401
to CN-CN909
to CN-CN910
to LED3-CN100
DIO8
Component side 3NA-V446020 14
DIO8
MAIN Circuit Board
Pattern side 3NA-V446020 15
Power Transformer
Power Transformer
to CN-CN913
DC Circuit Board
to CN-CN911
to MAIN-CN001
to CN-CN912
DIO8
Component side 16
3NA-V449590 3
DIO8
CN Circuit Board
to MAIN-CN902 to MAIN-CN901 from DC-CN404 from DC-CN403 from DC-CN402
3NA-V446040
Component side 17
DIO8
WC Circuit Board
WORD CLOCCK IN 75 OUT
OFF
ON
to MAIN-CN101
Component side
LED3 Circuit Board
AC Circuit Board
from MAIN-CN002
Component side
POWER ON/OFF
Power Transformer
Component side WC, LED3: 3NA-V505510 2 AC: 3NA-V449590 3 18
Power cord
DIO8
INSPECTION
1. 2.
2-1.
Range of Applicability
These specifications apply to the DIO8.
Preparations
Conditions Connect the DIO8 COM terminal (D-sub, 9-pin) and the PC serial port with a serial cross cable and carry out the various measurements by inputting commands from the terminal software on the PC. The function generator used for inspection must be the Sony Tektronix AFG310 or equivalent. When using the AFG310, the settings are as follows. FUNC: PULS MODE: CONT MODUL: OFF AMPL: 1.800 OFFSET: 0.900 Unless otherwise specified, the conditions are as follows. · Set the PORT B SELECTOR switch to 5-8. · Connect the function generator BNC output to DIO8 WORD CLOCK IN (BNC). · Set DIO8 WORD CLOCK IN 75 to ON. · Switch the DIO8 clock master to WORD CLOCK IN (BNC). Input set wc 0x07 from the PC. · 0 dBu = 0.775 Vrms · The oscillator output impedance is to be 150 . · The input impedance for the oscilloscope, level meter, etc. is to be at least 100 k. · The MY4-DA analog output load is to be 600 . · Set the MY4-AD and MY4-DA gain select switch to +18 dB. Test Program After the power on the DIO8 is started, inputting diag from the PC connected to the DIO8 starts the test program. For details on the starting method etc., refer to the Test Program Specifications KES-92623.
2-2.
3.
3-1.
Inspection
Inspection with Test Program · Inspect based on the Test Program Specifications KES-92623. Jitter Measurement · Insert the MY8-AE card into the DIO8 slot and connect to DSA1 through the D-sub Canon conversion box. · Set the function generator to 48 kHz and 44.1 kHz and measure the jitter at DSA1.
48 kHz 44.1 kHz Range of tolerance 6 nsec max. 5 nsec max.
3-2.
3-3.
Frequency Operation Range · Insert the MY4-AD card into DIO8 Slot 1 and the MY4-DA card into DIO8 Slot 5. · Connect OUTPUT A and INPUT B with a SCSI cable. (1) Fs = 51.12 kHz (48 kHz + 6.5 %) · Set the function generator to 51.12 kHz. · Input as in the table below. The output levels in the table below must be obtained. Also, test listen for one minute and verify that there is no noise.
Input frequency Input level Input terminal MY4-AD Ch1 Ch2 Ch3 Ch4 Output terminal MY4-DA Ch1 Ch2 Ch3 Ch4 Tolerance range +16 +/- 2 dBu +16 +/- 2 dBu +16 +/- 2 dBu +16 +/- 2 dBu
1 kHz
+16 dBu
(2) Fs = 39.69 kHz (44.1 kHz -10 %) · Set the function generator to 39.69 kHz. · Input the same as in 3-3 (1). The same output levels must be obtained. Also, test listen for one minute and verify that there is no noise.
19
DIO8
4.
Factory Settings
· Front panel PORT B Selector: · Rear panel WORD CLOCK IN 75 : 5-8 On
20
DIO8
TEST PROGRAM
A. DIO8 Overall Inspection Configuration
DIO8
SLOT 1 SLOT 2 SLOT 3 SLOT 4 SLOT 5 SLOT 6 SLOT 7 SLOT 8
SLOT For inspection jig 01V SLOT For inspection jig 01V SLOT For inspection jig 01V SLOT For inspection jig 01V SLOT For inspection jig 01V LMY-Slot inspection jig LMY-Slot inspection jig LMY-Slot inspection jig
CN201 CN201
ID change jig
OUTPUT A INPUT A CN102 CN101 CN103
ID change jig
OUTPUT B CN102 CN101 CN103 WORD CLOCK IN WORD CLOCK OUT WORD CLOCK OUT WORD CLOCK OUT WORD CLOCK OUT COM
Drawing Management Number 8B34E Drawing Number 01V Test Program Specifications Refer to the "Slot Inspection Jig Circuit Diagram". Drawing Management Number 8B87E Drawing Number LMY-Slot Inspection Jig Specifications Refer to the "LMY-Slot Inspection Jig Circuit Diagram".
KBS-92495
KBS-92650
PC Refer to the "ID Change Jig Circuit Diagram" on the same drawing.
The overall inspection items are (1) automatic inspection that checks connections automatically, (2) the Port B Selector inspection, (3) the 68-pin D-sub terminal (CN301, 501, 601, and 801) ID port inspection, (4) the WORD CLOCK terminal inspection, (5) the 7segment LED inspection. Also, the COM terminal connection check is OK if the test program starts. Load dio8diag program Version V1.01 before inspecting. (See Page 30 for the upgrade method.)
· Test program execution method Connect the PC and the DIO8 COM terminal with a D-sub 9-pin serial cross cable and start up Hyper Terminal or some other terminal program. Set the communications format settings to: Bit Rate: 38400 bps Data length: 8 bits Stop bit: 1 Parity: none Next, switch on the DIO8 power. The following is displayed in the terminal software window.
This is DIO8 2000 DIO8>
Use the PC keyboard to input "diag". The display changes to
DIO8>diag DIO8 Diagnosis version VX.X JAN.2000 DIO8_DIAG>
The DIO8 goes into test program mode. X.X is the test program version. To exit test program mode, input "reset" and the DIO8 goes into the following state, the same as when the power was first switched on.
DIO8_DIAG>reset This is DIO8 2000 DIO8>
(1) Automatic Inspection
When you execute
DIO8_DIAG>test
21
DIO8
the items below are inspected automatically and finally the OK/NG judgments are displayed plus the error list if there were any NGs. [Inspection items (test command)] 1. DSP5 #1 (IC201) and CPU connection check 2. DSP5 #2 (IC202) and CPU connection check 3. DSP5 parallel bus connection check 4. DSP5 #1 (IC201) and DIO IN A (CN301), DIO OUT A (CN501) connection check 5. DSP5 #2 (IC202) and DIO IN B (CN601), DIO OUT B (CN801) connection check 6. DSP5 #1 (IC201) and Slot 1 - Slot 4 connection check 7. DSP5 #2 (IC202) and Slot 5 - Slot 8 connection check 8. Slot control line connection check 9. DIO IN A, DIO IN B, DIO OUT A, DIO OUT B control line connection check 10. SRAM (IC013, IC014) and CPU connection check 11. Slot 1 serial interface connection check 12. Slot power line (12V system) check If the above 12 items are all OK,
DIAGNOSIS RESULT DIO8_DIAG> OK
is displayed and the program ends. If there was an NG item, an error list such as
DIAGNOSIS RESULT ERROR LIST [4] DIOA AUDIO LINE [5] DIOB AUDIO LINE : : NG XXXX XXXX XXXX XXXX XXXX XXXX XXXX XXXX
is displayed. (Only NG items) [ERROR LIST] [1] DSP5-1 <==> CPU Shows that there is an abnormality in the connection between DSP5 #1 (IC201) and the CPU. [2] DSP5-2 <==> CPU Shows that there is an abnormality in the connection between DSP5 #2 (IC202) and the CPU. [3] DSP PARALLEL BUS XXXX XXXX XXXX XXXX Shows that there is an abnormality in the DSP5 #1 (IC201) and DSP5 #2 (IC202) parallel bus connection. The PIO31, PIO30, ...PIO01, PIO00 states are displayed from the left. 0 is displayed for normal locations and X for abnormal locations. [4] DIOA AUDIO LINE XOXX OOOO XXXX OOOX These are the results of the DSP5 #1 and CN301 and CN501 connection checks. The path states SIO31-->CN501-->CN301-->SIO15 SIO30-->CN501-->CN301-->SIO14 : : SIO17-->CN501-->CN301-->SIO01 SIO16-->CN501-->CN301-->SIO00 are displayed from the left. 0 is displayed for normal locations and X for abnormal locations. [5] DIOB AUDIO LINE XXXX XXXX XXXX XXXX These are the results of the DSP5 #2 (IC202) and CN601 and CN801 connection checks. The path states SIO31-->CN801-->CN601-->SIO15 SIO30-->CN801-->CN601-->SIO14 : : SIO17-->CN801-->CN601-->SIO01 SIO16-->CN801-->CN601-->SIO00 are displayed from the left. 0 is displayed for normal locations and X for abnormal locations.
22
DIO8
[6] SLOT1-4 AUDIO LINE XXXX XXXX XXXX XXXX These are the results of the DSP5 #1 (IC201) and Slot 1, 2, 3 and 4 connection checks. The path states SIO63-->O4SLT4-->I4SLT4-->SIO58 SIO62-->O3SLT4-->I3SLT4-->SIO57 : : SIO37-->O2SLT1-->I2SLT1-->SIO33 SIO36-->O1SLT1-->I1SLT1-->SIO32 are displayed from the left. 0 is displayed for normal locations and X for abnormal locations. [7] SLOT5-8 AUDIO LINE XXXX XXXX XXXX XXXX These are the results of the DSP5 #2 (IC202) and Slot 5, 6, 7 and 8 connection checks. The path states SIO63-->O4SLT8-->I4SLT8-->SIO58 SIO62-->O3SLT8-->I3SLT8-->SIO57 : : SIO37-->O2SLT4-->I2SLT4-->SIO33 SIO36-->O1SLT4-->I1SLT4-->SIO32 are displayed from the left. 0 is displayed for normal locations and X for abnormal locations. [8] SLOT? DATA BUS XXXX XXXX XXXX XXXX SLOT? ADDR BUS XXX XXXX XXX SLOT? ETC.. XXX XXXX These are the results of the slot control line checks. A three-line message appears for each slot. The first line shows the states of the data bus from the left D15, D14, ... D1, D0. The second line shows the states of the address bus from the left A10, A9, ... A2, A1. The third line shows the states of the other control lines and clock lines from the left, YWC?, FS_MY, SYNC_MY, 64FS_MY, 128FS_MY, 256FS_MY, and /CON?. 0 is displayed for normal lines and X for abnormal lines. The "?" in the names stands for the slot number. [9] DIO IN A CONTROL LINE XXXX XXXX DIO OUT A CONTROL LINE XXXX XXXX DIO IN B CONTROL LINE XXXX XXXX DIO OUT B CONTROL LINE XXXX XXXX These are the results of the DIO IN A (CN301), B (CN601), DIO OUT A (CN501), B (CN801) control line checks. The connection states MSB/LSB, 2ch/4ch WC OUT, WC IN, DTR_OUT, RTS_IN, TX, RS are displayed from the left. 0 is displayed for normal lines and X for abnormal lines. [10]SRAM DATA BUS XXXX XXXX XXXX XXXX SRAM ADDR BUS XX XXXX XXXX XXXX XXX These are the results of the Slot 1 and CPU connection checks. The second line shows the states of the address bus from the left A17, A16, ... A2, A1 (seen from the CPU). The second line shows the states of the data bus from the left D15, D14, ... D1, D0. 0 is displayed for normal locations and X for abnormal locations. [11]SLOT1 SCI This is displayed when the result of the Slot 1 and CPU SCI1 connection check is NG. [12]SLOT SLOT SLOT SLOT SLOT SLOT +20D +3.3D +5D1 +5D2 -5A1 -5A2 SLOT SLOT SLOT SLOT SLOT SLOT -5A3 +5A1 +5A2 +5A3 -15A +15A
This is displayed when the result of the slot power (12V system) check is NG.
23
DIO8
(2) Port B Selector Inspection
When
DIO8_DIAG>sw
is executed, the display is as below and the system stands by for Port B Selector inspection.
CHANGE PORT B SELECTOR in 10 seconds .....
If you switch the switch within 10 seconds and there is no abnormality in the connection,
CHANGE PORT B SELECTOR in 10 seconds .....PORT B SELECTOR [OK] DIO8_DIAG>
is displayed and the Port B Selector ends. If the switch is not switched within 10 seconds or there was any abnormality in the connection,
CHANGE PORT B SELECTOR in 10 seconds .........Time out or [NG] DIO8_DIAG>
is displayed.
(3) D-sub 68-pin ID port inspection
Set DIAF inspection jig SW101 to ALL OFF and SW102 2 and 4 only On, then execute the command below. This executes the ID0-6 IN port inspection.
DIO8_DIAG>id in
If there is any abnormality, a message like the following is displayed.
DIO ID IN check NG DIOA IN ID IN LINE DIOA OUT ID IN LINE DIOB IN ID IN LINE DIOB OUT ID IN LINE XXX XXXX XXX XXXX XXX XXXX XXX XXXX
The ID 6, 5, 4, 3, 2, 1, and 0 IN states are displayed from the left. 0 is displayed for normal and X for abnormal. Next, switch on only 4, 5, and 6 for SW101 of the DAIF inspection jig and switch SW102 ALL OFF, then execute the command below. This executes the ID0-6 OUT port inspection.
DIO8_DIAG>id out
If there is any abnormality, a message like the following is displayed.
DIO ID IN check NG DIOA IN ID OUT LINE DIOA OUT ID OUT LINE DIOB IN ID OUT LINE DIOB OUT ID OUT LINE XXX XXXX XXX XXXX XXX XXXX XXX XXXX
The ID 6, 5, 4, 3, 2, 1, and 0 OUT states are displayed from the left. 0 is displayed for normal and X for abnormal.
(4) Word Clock terminal inspection
Connect the WORD CLOCK IN terminal and the WORD CLOCK OUT 1st terminal with a BNC cable. When
DIO8_DIAG>wc
is executed, the display is as below. Execute this for the other three WORD CLOCK OUT terminals and judge the results.
check WC BNC DIO8_DIAG> OK
(5) LED inspection
When
DIO8_DIAG>led
is executed, 0 1 ,0 2 ,0 3 ,0 4 ,0 5 ,0 6 ,0 7 ,0 8,0 8. 1 0 ,2 0 ,3 0 ,4 0 ,5 0 ,6 0 ,7 0 ,8 0,8.0 8.8. is displayed, so judge the results visually.
24
DIO8
B. DIO8 Main Sheet Inspection Configuration
Power supply
CN104 CN001 CN104 CN105 CN003
PC
Comm sheet
CN105
CN301
CN501
CN601
CN801
CN101
CN201
CN002
CN201
Slot inspection jig for 01V (Slots 1-6) LMY-Slot inspection jig (Slot 7) LMY-Slot inspection jig (Slot 8)
Main sheet being inspected
CN901
CN sheet
CN902
CN101
CN103 CN102
ID change jig
WORD CLOCK OUT
WC sheet
WORD CLOCK IN
WC sheet
Drawing Management Number 8B34E Drawing Number KBS-92495 01V Test Program Specifications Refer to the "Slot Inspection Jig Circuit Diagram". Drawing Management Number 8B87E Drawing Number KBS-92650 LMY-Slot Inspection Jig Specifications Refer to the "LMY-Slot Inspection Jig Circuit Diagram". Refer to the "ID Change Jig Circuit Diagram" on the same drawing. Refer to the COMM Circuit Diagram on Page 21 of this drawing.
CN101
CN103 CN102
ID change jig
The overall inspection items are (1) automatic inspection that checks connections automatically, (2) the 8-pin D-sub terminal (CN301, 501, 601, and 801) ID port inspection, (3) the CN002 inspection. Also, the CN003 terminal connection check is OK if the test program starts. Furthermore, check the CN105 CSLED line visually. If the three LEDS other than the blue one on the COMM sheet are flashing, the line is OK. Load the dio8diag program Version V1.01 before inspecting. (See Page 30 for the upgrading method.)
· Test program execution method Connect the PC and the DIO8 COM terminal with a D-sub 9-pin serial cross cable and start up Hyper Terminal or some other terminal program. Set the communications format settings to: Bit Rate: 38400 bps Data length: 8 bits Stop bit: 1 Parity: none Next, switch on the power. The following is displayed in the terminal software window.
This is DIO8 2000 DIO8>
Use the PC keyboard to input "diag". The display changes to
DIO8>diag DIO8 Diagnosis version VX.X JAN.2000 DIO8_DIAG>
The DIO8 goes into test program mode. X.X is the test program version. To exit test program mode, input "reset" and the DIO8 goes into the following state, the same as when the power was first switched on.
DIO8_DIAG>reset This is DIO8 2000 DIO8>
(1) Automatic Inspection
When you execute
DIO8_DIAG>sheet
25
DIO8
the items below are inspected automatically and finally the OK/NG judgments are displayed plus the error list if there were any NGs. [Inspection items (sheet command)] 1. DSP5 #1 (IC201) and CPU connection check 2. DSP5 #2 (IC202) and CPU connection check 3. DSP5 parallel bus connection check 4. DSP5 #1 (IC201) and DIO IN A (CN301), DIO OUT A (CN501) connection check 5. DSP5 #2 (IC202) and DIO IN B (CN601), DIO OUT B (CN801) connection check 6. DSP5 #1 (IC201) and Slot 1 - Slot 4 connection check 7. DSP5 #2 (IC202) and Slot 5 - Slot 8 connection check 8. Slot control line connection check 9. DIO IN A, DIO IN B, DIO OUT A, DIO OUT B control line connection check 10. SRAM (IC013, IC014) and CPU connection check 11. Slot 1 serial interface connection check 12. WORD CLOCK IN/OUT connection check 13. Option (IEEE1394) connector (CN105, CN105) connection check If the above 13 items are all OK,
DIAGNOSIS RESULT DIO8_DIAG> OK
is displayed and the program ends. If there was an NG item, an error list such as
DIAGNOSIS RESULT ERROR LIST [4] DIOA AUDIO LINE [5] DIOB AUDIO LINE : : NG XXXX XXXX XXXX XXXX XXXX XXXX XXXX XXXX
is displayed. (Only NG items) [ERROR LIST] For [1] - [11], see the error list for overall assembly. [12]WC BNC This is displayed when the result of the WORD CLOCK IN/OUT connection check is NG. [13]OPTION DATA BUS XXXX XXXX XXXX XXXX OPTION ADDR BUS XXX XXX OPTION CTRL LINE XX XXXX This displays the result of the Option (IEEE1394) connector (CN104, CN105) connection check. The first line shows the results of the data bus connection checks from the left D15, D14, ... D1, D0. The second line shows the states of the address bus from the left A6, A5, A4, A3, A2, A1. The third line shows the results of other connection checks and displays the results for /RDLINK, /WRLINK, /CS1394, /DREQ, /DRAK, /INT from the left.
(2) D-sub 68-pin ID Port Inspection
See the same item (Page 27) for the overall assembly.
(3) CN002 Connection Check
When
DIO8_DIAG>sw
is executed,
CHANGE PORT B SELECTOR in 10 seconds .....
is displayed and the system stands by for PORT B SELECTOR (SW100) inspection.
26
DIO8
If you switch the switch within 10 seconds and there is no abnormality in the connection,
CHANGE PORT B SELECTOR in 10 seconds .....PORT B SELECTOR [OK] DIO8_DIAG>
is displayed and the Port B Selector inspection ends. If the switch is not switched within 10 seconds or there was any abnormality in the connection between CN002 Pin 12 (DIO_B_SEL) and the CPU,
CHANGE PORT B SELECTOR in 10 seconds .........Time out or [NG] DIO8_DIAG>
is displayed. If you input the command below, the LEDs on the LED3 sheet should light up in the order given on Page 10. Verify that they do so to verify that the other connections for CN002 are correct.
DIO8_DIAG>led
C. Version Upgrade Method
The DIO8 has flash memory, so the firmware can be updated from the COM port. The version can also be upgraded from a Windows PC using special software. When the power is switched on, the system judges whether or not the system program is present in flash memory. If a normal system program is present, the system starts normally. If the program is not present or there is an abnormality in the program, then the system automatically goes into program boot mode.
2.2 Connection with DIO8
When you click the "Connect" switch, the command to put the DIO8 into program load mode is sent. If the connection is successful, the message below appears. When you click "OK", "dl" and "x.x" appear on the DIO8 7-segment LEDs alternating. (Where "x.x" is the software version; if F.F is displayed, the program, is not present.)
1. Connections
The connections are simple. Just connect the PC and the DIO8 COM terminal with a D-sub 9-pin serial cross cable as in the diagram below.
Dsub 9pin serial cross cable COM
DIO8
PC
2. Software
For the software, use LoadDio8/V1.0. When you open the folder, the three files LoadDio8.exe, TimeStamp.exe, and 02rv2.dll appear. The files needed for the version upgrade are LoadDio8.exe and 02rv2.dll.
2.3 Reading in the load file
When you press the Browse switch, a window like that below opens, so specify the file to load into the DIO8, then click the "Open" switch.
2.1 Starting the software
When you double click the LoadDio8.exe icon, the program starts and the display is as below. The COM terminal connected can be switched with the dialog box on the top right. (In this figure, COM1 has been selected.)
27
DIO8
2.4 Loading the program
Make sure you have "Dev1" set in the center top dialog box. When you click the "Load" switch, the program load starts. When it ends, the message below appears.
2.2 Connection with DIO8
When you click the "Connect" switch, the command to put the DIO8 into program load mode is sent. If the connection is successful, the message below appears. "dl" and "x.x" appear on the DIO8 7-segment LEDs alternating. (Where "x.x" is the software version)
2.3 Writing the date of manufacture 2.5 Others
You can reset the DIO8 to normal mode by clicking the Disconnect switch. When you click the SetDate switch, the year, month, and day of manufacture are written. When the date has been written, the message below appears.
D. Writing the Date of Manufacture
In order to support future protection methods, the year, month, and day of manufacture are written into the flash ROM using special software running on a PC.
1. Connections
The connections are simple. Just connect the PC and the DIO8 COM terminal with a D-sub 9-pin serial cross cable as in the diagram below.
2.4 Others
You can reset the DIO8 to normal mode by clicking the Disconnect switch.
Dsub 9pin serial cross cable COM
DIO8
PC
2. Software
For the software, use LoadDio8/V1.0. When you open the folder, the three files LoadDio8.exe, TimeStamp.exe, and 02rv2.dll appear. The files needed for writing the manufacturing date are TimeStamp.exe and 02rv2.dll.
2.1 Starting the software
When you double click the TimeStamp.exe icon, the program starts and the display is as below. The PC COM terminal can be switched with the dialog box on the top right. (In this figure, COM1 has been selected.)
28
DIGITAL IO BOX
PARTS LIST
CONTENTS
OVERALL ASSEMBLY······························································································································ 2 DC ASSEMBLY ········································································································································· 4 FRONT PANEL ASSEMBLY ····················································································································· 6 ELECTRICAL PARTS ························································································································· 7~11
Notes : DESTINATION ABBREVIATIONS
A: B: C: D: E: F: H: I : J: Australian model British model Canadian model German model European model French model North European model Indonesian model Japanese model M: South African model O: Chinese model Q: South-east Asia model T: Taiwan model U: U.S.A. model V: General export model (110 V) W: General export model (220 V) N,X: General export model Y: Export model
WARNING
Components having special characteristics are marked specification equal to those originally installed. and must be replaced with parts having
· · · · ·
The numbers in " QTY " show quantities for each unit. The parts with " - - " in " PART NO. " are not available as spare parts. The mark " " in the remarks column indicates that these parts are interchangeable. The second letter of the shaded ( ) part number is O, not zero. The second letter of the shaded ( ) part number is I, not one.
DIO8
OVERALL ASSEMBLY
40 56 300 420 430 430 210 90 220 260 440 50 450
40a 330 320 40b 330 330 240 270 340 310 350 280 290 130 120 150 520 370 70 400 360 410 411 530 230 550 250 40c
60 10 90 380 35 55 20 390 30 500 510 400 80 410 540
2
DIO8
REF NO.
*
* * *
* * * *
*
*
* * * * *
* *
10 20 30 35 40 40 40 40 40a 40a 40a 40b 40b 40b 40b 40c 40c 40c 50 55 56 60 70 80 90 120 130 150 210 220 230 240 250 260 270 280 290 300 310 320 330 340 340 350 360 360 360 370 380 380 390 400 410 420 430 440 450 500 510 520 530 540 550
PART NO. DESCRIPTION OVERALL ASSEMBLY -Overall Assembly -Overall Assembly -Overall Assembly -Overall Assembly V4761600 Bottom Shassis CB806590 Leg VR138400 Bind Head Tapping Screw-B -PET Sheet -Rear Panel Assembly -Rear Panel Assembly -Rear Panel Assembly -Rear Panel Assembly V4810900 Rear Panel V4762900 Rear Panel V4763000 Rear Panel VS228900 AC Cord Assembly VS229000 AC Cord Assembly VS229100 AC Cord Assembly VS229200 AC Cord Assembly CB806850 Cord Strain Relief CB811230 Cord Strain Relief CB032840 Cord Strain Relief VC688800 Bind Head Tapping Screw-B EG340360 Bind Head Screw V5362900 Panel V4761900 Side Panel VC688800 Bind Head Tapping Screw-B V4762000 Side Panel VC688800 Bind Head Tapping Screw-B V4460200 Circuit Board -Connector Assembly EP600230 Bind Head Tapping Screw-B V4535500 Circuit Board VS863000 Flat Head Screw -Support -Support VN413300 Bonding Tapping Screw-B VC688800 Bind Head Tapping Screw-B V4460400 Circuit Board -CN Support EP600230 Bind Head Tapping Screw-B -Connector Assembly VN413300 Bonding Tapping Screw-B -Angle Bracket VN413300 Bonding Tapping Screw-B V4774400 DC Aassembly V4775000 DC Aassembly VC688800 Bind Head Tapping Screw-B XW304A00 Power Transformer XW305A00 Power Transformer XW306B00 Power Transformer VC688800 Bind Head Tapping Screw-B -Front Panel Assembly -Front Panel Assembly VS153600 Oval Head Screw V4762700 Rack Mount Angle VS153600 Oval Head Screw V4774300 Top Cover VC688800 Bind Head Tapping Screw-B VZ678500 IF Plate VP156900 Bind Head Screw VC362700 Ferrite Core CB069250 Cord Holder -Shield Angle -Shield Angle VC688800 Bind Head Tapping Screw-B VC688800 Bind Head Tapping Screw-B ACCESSORIES V4789400 SCSI Cable
REMARKS
DIO8 J U,C,V H,W B (V476380) (V476390) (V476400) (V476410)
QTY
RANK
BL 4.0X12 MFZN2BL
J U,C,V H,W B J U,C,V H,W,B J U,C,V H,W B J U,C,V H,W U,C,V,H,W,B (V527490) (V476330) (V476340) (V476360) (V476370)
4 4 4
03 01
2P 15A 2.1m 3P 10A 2.5m 3P 6A 2.5m 3P 10A 2.5m SR-6N3-4 SR-6N-4 SR-5N-4 A4.0X8 MFZN2BL 4.0X8 MFZN2BL LEFT A4.0X8 MFZN2BL RIGHT A4.0X8 MFZN2BL DIO8 MAIN MAIN-DC VH 9P 3.0X6 MFZN2BL DIO8 WC (PNJK) 3.0X6 MFZN2BL OPT 1 OPT 2 3.0X8 MFZN2BL A4.0X8 MFZN2BL DIO8 CN 3.0X6 MFZN2BL CN-DC VH 7P 3.0X8 MFZN2BL 3.0X8 MFZN2BL
4
12 12 12 09 10 10 11 02 02 03 01 01 06 01 01 83 01 18 01
5 5
(V514320)
3 5
(V476100) (V476110)
4 7
(V476120)
01 01 32 01 01 01 47 01 18 18 18 01
6
(V514310)
2
(V476130)
8
J,U,C,V H,W,B
A4.0X8 MFZN2BL J A UL,CSA A CEE A A4.0X8 MFZN2BL
4
J U,C,V H,W,B
4
J,U,C,V H,W,B (V516390) (V516400)
4.0X8 MFZN2BL 4.0X8 MFZN2BL A4.0X8 MFZN2BL A4.0X12 MFZN2BL FR25/15/12-1400L BK-1 LOWER UPPER A4.0X8 MFZN2BL A4.0X8 MFZN2BL
3 2 8 16 8 16 2 2
(V581800) (V581790)
01 09 01 13 01 05 01 04 01
3 6
01 01
*
DHK-HA2-3000
2
27
*: New Parts
RANK: Japan only
3
DIO8
DC ASSEMBLY
30
30
110
10
100
120
70
145
20 90
140
80 50
40
130
FZ301 FZ300
FZ200 FZ201
60
FZ100
4
DIO8
REF NO.
* * * * * 10 20 30 40 50 60 70 80 90 100 110 120 130 140 145 FZ100 FZ100 FZ200 FZ200 FZ201 FZ201 FZ300 FZ300 FZ301 FZ301
PART NO. DESCRIPTION DC ASSEMBLY V4774400 DC Assembly V4775000 DC Assembly -Heat Sink V4766200 Heat Radiation Sheet 2 V4766100 Heat Radiation Sheet 1 V4496900 Circuit Board VP156800 Bind Head Screw EP600190 Bind Head Tapping Screw-B -Transistor Holder 1 EL200020 Pan Head Screw -Transistor Holder 2 EL200020 Pan Head Screw -DC Support L VP156800 Bind Head Screw -DC Support R VP156800 Bind Head Screw CB817510 Cord Binder VS823300 Fuse KB003250 Fuse KB003640 Fuse KB003250 Fuse KB003640 Fuse KB003250 Fuse KB003620 Fuse KB003090 Fuse KB003620 Fuse KB003090 Fuse
REMARKS
DIO8 J,U,V H,W,B (V476260)
QTY
RANK
47
2 DIO8 DC (PWCOM) A4.0X8 MFZN2BL 3.0X8 MFZN2BL
(V476590)
3 2 4
(V476600)
03 02 36 01 01 01 01 01 01 03 02 01 01 01 01 01 01 01 01 01
SP 4.0X8 MFZN2Y SP 4.0X8 MFZN2Y
(V516140)
5 2
(V516150)
A4.0X8 MFZN2BL A4.0X8 MFZN2BL S-14B T 8.00A JU TL 6.30A S T 6.00A JU TL 6.30A S T 6.00A JU TL 6.30A S T 4.00A JU T 3.15A S T 4.00A JU T 3.15A S
2
J,U,V H,W,B J,U,V H,W,B J,U,V H,W,B J,U,V H,W,B J,U,V H,W,B
*: New Parts
RANK: Japan only
5
DIO8
FRONT PANEL ASSEMBLY
FZ600 70
40
90
60
50
80 100 20 10 100
30
PART NO. DESCRIPTION FRONT PANEL ASSEMBLY -Front Panel Assembly -Front Panel Assembly * 10 V4762500 Front Panel * 20 V4278800 Window, 7-seg. 30 VL813000 Escutcheon, Power Switch 40 -Front Chassis * 50 V4769700 Circuit Board 60 EP600230 Bind Head Tapping Screw-B * 70 V4496400 Circuit Board 80 VC688800 Bind Head Tapping Screw-B 90 VL812900 Power Switch Knob 100 VS153600 Oval Head Screw * FZ600 VS823300 Fuse FZ600 KB003090 Fuse
REF NO.
REMARKS
DIO8 J,U,V H,W,B (V516390) (V516400)
QTY
RANK
05 03
(V476180)
DIO8 LED3 (PNJK) 3.0X6 MFZN2BL DIO8 AC (PWCOM) A4.0X8 MFZN2BL
POWER ON/OFF
2 4 5
J,U,V H,W,B
4.0X8 MFZN2BL T 8.00A JU T 3.15A S
09 01 09 01 03 01 02 01
*: New Parts
RANK: Japan only
6
DIO8
ELECTRICAL PARTS
REF NO.
* * * * * * * * C104 * C105 C107 * C108 C110 * C111 C113 * C114 C116 * C117 C119 * C120 C122 C204 C205 C208 C209 C212 C213 C216 C217 C304 C305 C308 C309 C500 * C600
PART NO. DESCRIPTION ELECTRICAL PARTS V4496400 Circuit Board V4496900 Circuit Board V4460400 Circuit Board V4769700 Circuit Board V4535500 Circuit Board V4460200 Circuit Board V4496400 V4496900 VY830900 UR868470 UR848470 UR868470 UR848470 UR868470 UR848470 UR868470 UR848470 UR868470 UR848470 UR868470 UR848470 VT598600 VT598600 UR838100 UR838100 UR838100 UR838100 UR838100 UR838100 UR759220 UR759220 UR848100 UR848100 V3311600 V5170300 VS589000 FG644100 UA355100 LB932050 LB932030 VK025200 LB932090 LB932070 VK025800 VF728300 LB933030 LB933030 V5129900 V5129900 VB481900 VB481900 VB481900 VB481900 VT682400 VT682400 VT682400 FZ006970 FZ006970 FZ006970 FZ006970 FZ006920 FZ006920 VP206500 VP206500 VP206500 VP206500 VP206500 VP206500 Circuit Board Circuit Board Electrolytic Cap. Electrolytic Cap. Electrolytic Cap. Electrolytic Cap. Electrolytic Cap. Electrolytic Cap. Electrolytic Cap. Electrolytic Cap. Electrolytic Cap. Electrolytic Cap. Electrolytic Cap. Electrolytic Cap. Electrolytic Cap. Electrolytic Cap. Electrolytic Cap. Electrolytic Cap. Electrolytic Cap. Electrolytic Cap. Electrolytic Cap. Electrolytic Cap. Electrolytic Cap. Electrolytic Cap. Electrolytic Cap. Electrolytic Cap. Electrolytic Cap. Capacitor Capacitor Ceramic Capacitor-E Ceramic Capacitor-F Mylar Capacitor Base Post Connector Base Post Connector Wire Trap Base Post Connector Base Post Connector Wire Trap Wire Trap Base Post Connector Base Post Connector Diode Diode Diode Diode Diode Diode Diode Stack Diode Stack Diode Stack LC Filter LC Filter LC Filter LC Filter LC Filter LC Filter Fuse Holder Fuse Holder Fuse Holder Fuse Holder Fuse Holder Fuse Holder
REMARKS
DIO8
QTY
RANK
DIO8 AC (PWCOM) DIO8 DC (PWCOM) DIO8 CN DIO8 LED3 (PNJK) DIO8 WC (PNJK) DIOO8 MAIN DIO8 AC (PWCOM) DIO8 DC (PWCOM) 15000 63.0V 470.00 50.0V 470.00 25.0V 470.00 50.0V 470.00 25.0V 470.00 50.0V 470.00 25.0V 470.00 50.0V 470.00 25.0V 470.00 50.0V 470.00 25.0V 470.00 50.0V 470.00 25.0V 22000 16 USP 22000 16 USP 100.00 16.0V 100.00 16.0V 100.00 16.0V 100.00 16.0V 100.00 16.0V 100.00 16.0V 2200 35.0V 2200 35.0V 100.00 25.0V 100.00 25.0V 0.01 250V J.U.C.S 0.22 275V U.C.S 4700P 500V M 0.01 50V Z 0.1 50V J VH- 5P TE VH- 3P TE 52147 8P TE VH- 9P TE VH- 7P TE 52147 14P TE 52147 6P TE VH- 3P SE VH- 3P SE D3S6M-4001P15 D3S6M-4001P15 11ES4 11ES4 11ES4 11ES4 D6SB60L 6.0A 600V D6SB60L 6.0A 600V D6SB60L 6.0A 600V LS MT Y223NB LS MT Y223NB LS MT Y223NB LS MT Y223NB LS MT B271KB LS MT B271KB EYF-52BC EYF-52BC EYF-52BC EYF-52BC EYF-52BC EYF-52BC
(XW649B0) (XW649B0) (XW641A0) (XW684B0) (XW684B0) (XW640A0) (XW649B0) (XW649B0)
09 36 32 09 18 83 09 36 11 01 01 01 01 01 01 01 01 01 01 01 01 05 05 01 01 01 01 01 01 02 02 01 01 01 01 01 01 01 01 01 01 01 01 01 01 01 01 02 02 01 01 01 01 04 04 04 02 02 02 02 01 01 01 01 01 01 01 01
CN001 CN002 CN400 CN401 CN402 CN403 CN404 CN600 CN602 * D100 * -105 D200 -211 D300 -303 DB100 DB200 DB300 EM100 -105 EM200 -205 EM300 EM301 FZ100 FZ200 FZ201 FZ300 FZ301 FZ600
*: New Parts
RANK: Japan only
7
DIO8
REF NO.
*
* * *
IC100 -104 IC105 IC200 IC201 IC202 IC203 IC204 IC205 IC300 IC301 IC302 K400 -402 K600 L100 -105 L600 SW500 TR300
PART NO. XT514A00 XT514A00 XW241A00 XR607A00 XK309A00 XR607A00 XK309A00 XR607A00 XK309A00 XR608A00 XD854A00 XD631A00 ---V2379700 V2379700 V4122100 V3127000 IA101590 HF757100 HF756470 V4460400 VU328200 VU328200 VT640300 VT640300 LB933070 VI879200 VI878400 --V4769700 V4535500 UF037470 UB051330 UB052100 UB245100 VI878300 VI879000 VV556300 VV556300 FZ006970 FZ006920 XN976A00 XU816A00 XU816A00 VI552200 VI552200 VS740100 V4078200 -VQ907900 VG837400 --RD253470 RD254470 RD254750 RD256220 V4460200 UF118330 UF018100 UF018100 UF118330 UF118330 UF017470
DESCRIPTION IC IC IC IC IC IC IC IC IC IC IC IC Land Terminal Land Terminal AC Shield Plate Coil Coil Line Filter Push Switch Transistor Carbon Resistor Carbon Resistor Circuit Board Plug Plug Receptacle Receptacle Base Post Connector Cable Holder Cable Holder Ribbon Cable Ribbon Cable Circuit Board Circuit Board Electrolytic Cap. (chip) Monolithic Ceramic Cap. Monolithic Ceramic Cap. Monolithic Ceramic Cap. Cable Holder Cable Holder Diode Array Diode Array LC Filter LC Filter IC IC IC BNC Connector BNC Connector Chip Inductance LED Display Spacer, 7-seg. Slide Switch Slide Switch Ribbon Cable Ribbon Cable Carbon Resistor (chip) Carbon Resistor (chip) Carbon Resistor (chip) Carbon Resistor (chip) Circuit Board Electrolytic Cap. (chip) Electrolytic Cap. (chip) Electrolytic Cap. (chip) Electrolytic Cap. (chip) Electrolytic Cap. (chip) Electrolytic Cap. (chip)
REMARKS SI-8050S(LF1103) SI-8050S(LF1103) SI-8033S UPC2405AHF NJM7905FA UPC2405AHF NJM7905FA UPC2405AHF NJM7905FA UPC2415AHF NJM7915FA PST518B-TP
DC-DC CONVERTER DC-DC CONVERTER REGULATOR +3.3V REGULATOR +5V REGULATOR -5V REGULATOR +5V REGULATOR -5V REGULATOR +5V REGULATOR -5V REGULATOR +15V REGULATOR -15V SYSTEM RESET (V476150) (V476150) (V516130)
QTY
RANK
05 05 05 04 03 04 03 04 03 04 03 02
HP-033JY 150 HP-033JY 150 PLH10A7003R6P02 ESB92S23B J.U.C.S 2SA1015 O,Y 10.0K 1/4 J 4.7K 1/4 J DIO8 CN PHEC 100P TE PHEC 100P TE PHEC 100P SE PHEC 100P SE VH- 7P SE 51048 14P TE 51048 6P TE P=2.0 #26 14P 260L P=2.0 #26 6P 240L DIO8 LED3 (PNJK) DIO8 WC (PNJK) 47 16V SL 33P 50V J SL 100P 50V J F 0.1 25V Z 51048 5P TE 51048 12P TE DAN217 0.3A X2 DAN217 0.3A X2 LS MT Y223NB LS MT B271KB SN75124NS SN75121NSR SN75121NSR YKS11-0 1P YKS11-0 1P BLM21B751S 2125 LNM423AS01 2S SSSU112-S06N-1 SSSB04 P=2.0 #26 5P 180L P=2.0 #26 12P 320L 4.7 0.1 J 47.0 0.1 J 75.0 0.1 J 2.2K 0.1 J DIO8 MAIN 330 6.3V UUR0J3 100 6.3V 100 6.3V 330 6.3V UUR0J3 330 6.3V UUR0J3 47 6.3V
POWER ON/OFF
06 06 02 02 01 01 01
(XW641A0)
* CN901 -908 CN909 CN910 CN911 CN912 CN913 W912 W913 * * C1
1,2,3,4,5,6,7,8
32 05 05 04 04 01 01 01
(V513050) (V513020) (XW684B0) (XW684B0)
CN001 CN100 DA001 -005 EM001 -006 IC001 IC002 IC003 JK001 -005 L001 * LD100 LS100 SW001 SW100 W001 W100
LINE RECEIVER LINE DRIVER LINE DRIVER WORD CLOCK IN,OUT
I/O UNIT ID (V441160) WORD CLOCK 75ohm OFF/ON PORT B SELECTOR 5-8/1-4 (V513010) (V229760)
09 18 01 01 01 01 01 01 01 01 02 01 05 05 05 05 05 03 06 01 03
01 01 01 01
(XW640A0)
* C1 C2 C16 C52 C53 C131
83 01 01 01 01 01 01
*: New Parts
RANK: Japan only
8
DIO8
REF NO.
C139 -141 C153 C161
* * * *
* * * * * * * * *
CN001 CN002 CN003 CN101 CN102 CN104 CN105 CN301 CN501 CN601 CN801 CN901 CN902 DA301 -344 DA501 -544 DA601 -644 DA801 -844 EM001 EM002 EM003 EM006 EM007 EM008 EM101 EM201 EM301 -305 EM306 -309 EM501 -505 EM506 -509 EM601 -605 EM606 -609 EM801 -805 EM806 -809 IC001 IC002 IC003 -006 IC007 IC008 IC009 IC010 IC011 IC012 IC013 IC014 IC015 IC016 IC017
PART NO. UF017470 UF017470 UF017470 UF017470 UB051220 UB012470 UB445330 UB245100 VR327000 VR327300 LB932090 VK025600 VU196300 VK024900 VQ623900 VQ048500 VQ048500 V4158600 V4158600 V4158600 V4158600 VU328200 VU328200 VV556300 VV556300 VV556300 VV556300 VV556300 VV556300 VV556300 VV556300 FZ006970 FZ006970 FZ006920 FZ006920 FZ006970 FZ006970 FZ006970 FZ006970 VL534100 VL534100 VQ761400 VQ761400 VL534100 VL534100 VQ761400 VQ761400 VL534100 VL534100 VQ761400 VQ761400 VL534100 VL534100 VQ761400 VQ761400 XT487A00 XU073A00 XT487A00 XT487A00 IS027300 IS000800 XV721A00 IS013810 IS013810 XP226A00 XV305A00 XV305A00 IS027300 IS003200 IS003200
DESCRIPTION Electrolytic Cap. (chip) Electrolytic Cap. (chip) Electrolytic Cap. (chip) Electrolytic Cap. (chip) Monolithic Ceramic Cap. Monolithic Ceramic Cap. Monolithic Ceramic Cap. Monolithic Ceramic Cap. Mylar Capacitor (chip) Mylar Capacitor (chip) Base Post Connector Wire Trap Socket Wire Trap Pin Header Connector, FFC Connector, FFC Connector Connector Connector Connector Plug Plug Diode Array Diode Array Diode Array Diode Array Diode Array Diode Array Diode Array Diode Array LC Filter LC Filter LC Filter LC Filter LC Filter LC Filter LC Filter LC Filter LC Filter LC Filter EMI Filter (chip) EMI Filter (chip) LC Filter LC Filter EMI Filter (chip) EMI Filter (chip) LC Filter LC Filter EMI Filter (chip) EMI Filter (chip) LC Filter LC Filter EMI Filter (chip) EMI Filter (chip) IC IC IC IC IC IC IC IC IC IC IC IC IC IC IC
REMARKS 47 6.3V 47 6.3V 47 6.3V 47 6.3V SL 22P 50V J B 470P 50V K F 0.33 16V Z F 0.1 25V Z F 0.047 25V Z F 0.082 25V Z VH- 9P TE 52147 12P TE 17LE-23090-27(D4CH 52147 5P TE HIF3H-10PB-2.54DSA 52045 36P TE 52045 36P TE 230R(SCSI) 68P SE 230R(SCSI) 68P SE 230R(SCSI) 68P SE 230R(SCSI) 68P SE PHEC 100P TE PHEC 100P TE DAN217 0.3A X2 DAN217 0.3A X2 DAN217 0.3A X2 DAN217 0.3A X2 DAN217 0.3A X2 DAN217 0.3A X2 DAN217 0.3A X2 DAN217 0.3A X2 LS MT Y223NB LS MT Y223NB LS MT B271KB LS MT B271KB LS MT Y223NB LS MT Y223NB LS MT Y223NB LS MT Y223NB NFA81R00C101 NFA81R00C101 NFM40R01C101T1 NFM40R01C101T1 NFA81R00C101 NFA81R00C101 NFM40R01C101T1 NFM40R01C101T1 NFA81R00C101 NFA81R00C101 NFM40R01C101T1 NFM40R01C101T1 NFA81R00C101 NFA81R00C101 NFM40R01C101T1 NFM40R01C101T1 TC74VHC245F SN75C1168NSR TC74VHC245F TC74VHC245F HD74LV273AFPEL HD74LV08AFPEL HD6437042AF53F SN74LV138ANSR SN74LV138ANSR IC-PST591DMT IS61C1024-20J IS61C1024-20J HD74LV273AFPEL HD74LV32AFPEL HD74LV32AFPEL
QTY
RANK
COM
INPUT A(1-4)(1-8) OUTPUT A(1-4)(1-8) INPUT B(1-4/5-8) OUTPUT B(1-4/5-8)
TRANSCEIVER LINE TRANSCEIVER TRANSCEIVER TRANSCEIVER D-FF AND CPU DECODER DECODER SYSTEM RESET SRAM 1M SRAM 1M D-FF OR OR
01 01 01 01 01 01 01 01 01 01 01 01 04 01 03 02 02 06 06 06 06 05 05 01 01 01 01 01 01 01 01 02 02 01 01 02 02 02 02 05 05 01 01 05 05 01 01 05 05 01 01 05 05 01 01 03 05 03 03 02 01 09 01 01 03 09 09 02 01 01 RANK: Japan only
*: New Parts
9
DIO8
REF NO.
*
* * * *
*
* * * * * * *
IC018 IC019 -022 IC024 IC025 -029 IC030 -035 IC101 IC102 IC103 IC104 IC106 IC107 IC108 -110 IC111 IC112 -114 IC115 IC116 IC117 IC118 IC119 IC120 IC201 IC202 IC203 -210 IC301 IC302 -306 IC307 -310 IC501 -505 IC506 IC601 IC602 -606 IC607 -610 IC801 -805 IC806 L001 L101 -103 L105 L106 -114 L115 -117 L118 -143 L144 L201 L901 -946 R112 R113 R115 -117 R118 R119 R120 R123 R124
PART NO. XU948A00 XT487A00 XT487A00 IS013910 XS720A00 XS720A00 XT487A00 XT487A00 XY102A00 XW239A00 XT487A00 XY217A00 XG948E00 IS000400 XG948E00 XG948E00 XW422A00 XT487A00 XT487A00 XG948E00 XW422A00 XW422A00 IS000000 IS000800 XY094A00 XV989A00 XV989A00 XT487A00 XT487A00 XU996A00 XU815A00 XU815A00 XU235A00 XU235A00 XU996A00 XU996A00 XU815A00 XU996A00 XU815A00 XU815A00 XU235A00 XU235A00 XU996A00 XU996A00 XU815A00 GE300610 VS740100 VS740100 GE300610 VS740100 VS740100 GE300610 GE300610 VS740100 VS740100 GE300610 VS740100 VS740100 VS740100 VI196100 VI194600 VI196100 VI196100 VI194100 VI194100 VI194600 VI196100 VI194100 RD250000 RD254100
DESCRIPTION IC IC IC IC IC IC IC IC IC IC IC IC IC IC IC IC IC IC IC IC IC IC IC IC IC IC IC IC IC IC IC IC I