Text preview for : B_Disassembly and Assembly Procedure_v1.pdf part of OLYMPUS C-3040 Zoom S.M.



Back to : OLYMPUS C-3040 Zoom.part | Home

B. DISASSEMBLY AND ASSEMBLY PROCEDURE

C-3040 Zoom

B. DISASSEMBLY AND ASSEMBLY PROCEDURE
REMOVAL OF CABINET TOP ASSEMBLY, CABINET FRONT ASSEMBLY AND CABINET BACK ASSEMBLY ...................... B-2 [2] REMOVAL OF LENS VF AND FLEXIBLE PWB .................................................... B-3 [3] REMOVAL OF LENS ASSEMBLY AND CA1 BOARD ........................................... B-4 [4] REMOVAL OF SY1 BOARD,CA2 BOARD AND ST1 BOARD ............................... B-4 [5] BOARD LOCATION ................................................................................................ B-5 [1]

SERVER_DIS

B-1

Ver.1

B. DISASSEMBLY AND ASSEMBLY PROCEDURE

C-3040 Zoom

[1]REMOVAL OF ABINET TOP ASSEMBLY,CABINET FRON TASSEMBLY AND CABINET BACK ASSEMBLY Disassembly perform as follows (1, 2...23) and assembly perform by reversing the disassembly steps (23, 22...1). Be sure to discharge the main capacitor in procedure 11, then continueu to disassembling.

!

Beware of electric shock
Danger of electric shock. Use a discharging tool to remove the electrical charge before working.

When assembling, attach the spacers to the holder monitor in the order 20, 19, 18 and 21.

22. Holder monitor 20. Spacer monitor light B 17. Screw 1.7 x 4 18. Spacer monitor light 2. Screw 1.4 x 3.5 3. Cover dial 23. LCD

19. Spacer monitor light C 4. Screw 1.7 x 3.5 5. Cabinet top 21. Spacer shield 1. Two screws monitor 1.7 x 3.5 16. Connector 8. Cover card 9. Two screws 1.7 x 8 13. FPC

9. Screw 1.7 x 4 10. Cabinet front

14. Cabinet back 15. FPC

11.Discharge both ends of C5412. (ST1 board side A)
12. Connector & de-solder two wires(Red,White) 7. Three screws 1.7 x 4 6. Open the cover battery.

SERVER_DIS

B-2

Ver.1

C-3040 Zoom

B. DISASSEMBLY AND ASSEMBLY PROCEDURE

[2] REMOVAL OF LENS VF AND FLEXIBLE PWB

2. Screw 1.7 x 4 3. Reflector

6. Screw 1.7 x 4 7. Holder mode 1. LCD

9. Two screws 1.7 x 4 12. FPC 8. Screw 1.4 x 3.5 11. Flexible PWB 13. Two screws 1.7 x 4 10. Connector 14. Lens VF

5. Spacer chassis 4. Spacer sheet 17. Connector

16. Holder LED 15. Screw 1.7 x 4 18. Microphone

When installing 1. Gear 1 should be positioned correctly. 2. The lens VF should be in the extended position.

Ver.1

B-3

SERVER_DIS

B. DISASSEMBLY AND ASSEMBLY PROCEDURE [3] REMOVAL OF LENS ASSEMBLY AND CA1 BOARD

C-3040 Zoom

When assembling, the lens VF and the gear 1 should be positioned correctly before installing the lens assembly.
5. Two screws 6. Screw 2 x 6 2 x 2.5 7. CA1 board
B

B A

C

3. Two FPCs
C

A

4. PFC
Lens CCD

Install so that it is perpendicular.
2. Screw 1.7 x 6 1. Three screws 1.7 x 4

[4] REMOVAL OF SY1 BOARD, CA2 BOARD AND ST1 BOARD

1. Screw 1.7 x 4 5. Holder BRKT SY 4. SY1 board 6. Two screws 1.7 x 4 7. Connector 3. Connector 2. Screw 1.7 x 4

10. Connector

D

8. CA2 circuit

D

11. ST1 board

9. Two screws 1.7 x 4

SERVER_DIS

B-4

Ver.1

C-3040 Zoom [5] BOARD LOCATION

B. DISASSEMBLY AND ASSEMBLY PROCEDURE

SY1 board

CA2 board

ST1 board

CA1 board

Ver.1

B-5

SERVER_DIS