Text preview for : JVC AV-28RH4BU_SU.pdf part of JVC AV-28RH4BU_AV-28RH4SU full service manual & schematic



Back to : JVC AV-28RH4BU_SU.part1.r | Home

Preliminary

SERVICE MANUAL
COLOUR TELEVISION

AV-28RH4BU,
AV-28RH4SU
Supplementary




The following item for the AV-28RH4BU, AV-28RH4SU models were changed partly from
AV-28KH1BUF model. Therefore, this Service Manual describes only the SPECIFICATIONS,
SPECIFIC SERVICE INSTRUCTIONS & PARTS LIST.
For details other than those described in this manual, please refer to the AV-28KH1BUF model
SERVICE MANUAL (No.52139, 2003/9).


TABLE OF CONTENTS
1 SPECIFICATIONS........................................................................................................................... 2
2 SPECIFIC SERVICE INSTRUCTIONS ........................................................................................... 3
3 PARTS LIST .................................................................................................................................... 5




1 COPYRIGHT © 2004 Victor Company of Japan, Limited No.YA077
2004/10
SPECIFICATIONS
Content
Item
AV-28RH4BU / AV-28RH4SU
Dimensions ( W×H×D ) 76.5 cm x 58.5 cm x 48.6 cm
Mass 33.8kg
TV RF System B/G, D/K, L/L'
Colour System TV Mode PAL / SECAM
Video Mode PAL / SECAM / NTSC 3.58 / NTSC 4.43
Sound System A2(Germany system), NICAM(B/G, D/K, L/L')
Teletext System Fastext / Toptext / WST
Receiving Frequency
VHF(VL) 46.25MHz 168.25MHz
(VH) 175.25MHz 463.25MHz
UHF 471.25MHz 863.25MHz
CATV S01-S20 / S21-S41
Intermediate Frequency
VIF Carrier 38.9MHz (B/G , D/K , L) / 33.9MHz(L')
SIF Carrier 33.4MHz (5.5MHz:B/G) / 32.9MHz (6.0MHz:D/K)
32.4MHz (6.5MHz:L) / 40.4MHz (6.5MHz:L')
Colour Sub Carrier Freq.
PAL 4.43MHz
SECAM 4.40625MHz / 4.43MHz
NTSC 3.58MHz / 4.43MHz
Power Input AC 175V265V , 50Hz
Power Consumption 150W (Max), 3W (Standby)
Aerial Input Term 75unbalanced, Coaxial
Picture Tube Size Visible size : 66cm( Measured diagonally)
High Voltage 30kV (at zero beam current)
Speaker 5.7cm×12.6cm, Oval type×2
Audio Output Tweeter : 10W+10W (closed), 8/10W+10W
Input Video 1V(p-p), 75
S/Video Mini DIN 4pin
Y : 1V(p-p) Positive, 75 / C : 0.286V(p-p), 75
Audio(L/R) 500mV(rms),(-4dBs), High Impedance
Output Video 1V(p-p) 75
Audio(L/R) 500mV(rms), Low Impedance
Input Terminal Rear Side AV1 (Video/Audio/RGB)
AV2 (Video/Audio/S-VHS)
Front Side AV3(FRONT AV) (Video/Audio)
Output Front Side Headphone jack (Stereo mini jack 3.5mm)
Terminal
Rear Side AV1 (Video/Audio)
AV2 (Video/Audio)
Remote Control Unit VE-30017763 (RM-C1100), (AA/R06 dry battery×2)
Design & specifications are subject to change without notice.




2No. YA077
SPECIFIC SERVICE INSTRUCTIONS
DISASSEMBLY PROCEDURE
REMOVING THE REAR COVER REMOVING THE POWER SWITCH PWB
1. Unplug the power cord. Removing the rear cover.
2. Remove the 10 screws marked [A]. 1. Remove the 2 screws marked [I], and remove the
3. Remove the 4 screws marked [B]. POWER SWITCH PWB.
4. Withdraw the REAR COVER toward you.

REMOVING THE LED PWB
REMOVING THE BACK DOOR Removing the rear cover.
Removing the rear cover. 1. Remove the 2 screws marked [J], and remove the LED
1. Remove the 2 screws marked [C]. PWB.
2. Withdraw the BACK DOOR toward you.

REMOVING THE BASE
REMOVING THE MAIN PWB Removing the rear cover.
Removing the rear cover. 1. Remove the 2 screws marked [K], and remove the
Removing the back door. BASE.
1. Remove the 4 screw marked [D].
2. Slightly raise the both sides of the MAIN PWB by hand
CHECKING THE PW BOARD
and withdraw MAIN PWB back ward.
To check the back side of the PW Board.
[CAUTION]
1) Pull out the PW Board. (Refer to REMOVING THE
If necessary, take off the wire clamp, connectors etc.
MAIN PWB).
Be careful enough when developing a MAIN PWB.
2) Erect the PW Board vertically so that you can easily
check the back side of the PW Board.
REMOVING THE FEATURE BOX PWB
[CAUTION]
Removing the rear cover.
When erecting the PW Board, be careful so that there will
1. Disconnect the connector PL409 and PL410 on the
be no contacting with other PW Board.
MAIN PWB.
Before turning on power, make sure that the wire
2. Raise up the both sides and disconnect the FEATURE
connector is properly connected.
BOX PWB.
When conducting a check with power supplied, be sure to
confirm that the CRT EARTH WIRE (BRAIDED ASS'Y) is
REMOVING THE WOOFER & TWEETER
connected to the CRT SOCKET PW board.
Removing the rear cover.
1. Remove the 4 screws marked [E], and remove the
WOOFER. WIRE CLAMPING AND CABLE TYING
2. Remove the 4 screws marked [F], and remove the 1. Be sure to clamp the wire.

TWEETER. 2. Never remove the cable tie used for tying the wires

3. Remove an opposite side similarly. together.
Should it be inadvertently removed, be sure to tie the
wires with a new cable tie.
REMOVING SIDE CONTROL PWB
Removing the rear cover.
1. Remove the 2 screws marked [G], and remove the SIDE
CONTROL PWB.

REMOVING SWITCH PWB
Removing the rear cover.
1. Remove the 3 screws marked [H], and remove the SIDE
SWITCH PWB.




No. YA0773
4No. YA077
PARTS LIST
USING P.W. BOARD & REMOTE CONTROL UNIT
Model AV-28RH4BU
PWB ASS'Y AV-28RH4SU

MAIN PWB VE-20160399

FEATURE BOX PWB VE-20144446

CRT SOCKET PWB VE-20147459

LED PWB VE-20154915

SIDE CONTROL PWB VE-20161117

SWITCH PWB VE-20167596

POWER SWITCH PWB VE-20122229

VE-30017763
REMOTE CONTROL UNIT
(RM-C1100)



EXPLODED VIEW PARTS LIST
Ref.No. Part No. Part Name Description Local
V01 VE-30002754 PICTURE TUBE(ITC) Inc.DY,PC MAGNET
L01 VE-30029994 DEG.COIL
TR101 VE-30017521 FBT within MAIN PWB
1 VE-20160977 FRONT CABINET AV-28RH4BU
1 VE-20161093 FRONT CABINET AV-28RH4SU
2 VE-40013592 LOGO JVC AV-28RH4BU
2 VE-40013593 LOGO JVC AV-28RH4SU
3 VE-35000013 SPRING
4 VE-20144094 BUTTON ON/OFF AV-28RH4BU
4 VE-20160953 BUTTON ON/OFF AV-28RH4SU
5 VE-20144095 BUTTON FUNCTION AV-28RH4BU
5 VE-20160956 BUTTON FUNCTION AV-28RH4SU
6 VE-20128755 LENS PRE-AMP
7 VE-20056446 LED LENS
8 VE-40000082 FOOT RUBBER (X2)
9 VE-30024903 SPEAKER (X2) 815W 57*126
10 VE-30024912 TWEETER (X2) 8 8W CLOSED
11 VE-20004520 CABLE HOLDER
12 VE-20141523 BASE
13 VE-30018270 PFC TRANSF. 1.7A 43MH 170W
14 VE-20090585 CHASSIS FRAME
15 VE-20168677 BACK DOOR AV-28RH4BU
15 VE-20120043 BACK DOOR AV-28RH4SU
16 VE-35008081 SCREW (3X9.5) (X4)
17 VE-20144073 REAR COVER AV-28RH4BU
17 VE-20160941 REAR COVER AV-28RH4SU
18 VE-35004572 SCREW (4X20) (X10) AV-28RH4BU
18 VE-35010702 SCREW (4X20) (X10) AV-28RH4SU
19 VE-20160975 LABEL AV-28RH4BU
19 VE-20160981 LABEL AV-28RH4SU
20 VE-30016513 POWER CORD 2.2MT





No. YA0775
EXPLODED VIEW




6No. YA077
PACKING




PACKING PARTS LIST
Ref.No. Part No. Part Name Description Local

1 VE-50051238 CARTON BOX AV-28RH4BU
1 VE-50051256 CARTON BOX AV-28RH4SU
2 VE-20155898 CUSHION ASS'Y 4pcs in 1set
3 VE-50042308 POLY BAG(1200*1050)
4 VE-70000587 POLY BAG
5 VE-30017763 REMOTE CONTROL UNIT(RM-C1100)
6 VE-50051235 INST BOOK(EN/GE/FR/IT/SP/DU/POR) AV-28RH4BU
6 VE-50051243 INST BOOK(EN/GE/FR/IT/SP/DU/POR) AV-28RH4SU
7 VE-50051236 INST BOOK(SW/NO/DA/FIN) AV-28RH4BU
7 VE-50051254 INST BOOK(SW/NO/DA/FIN) AV-28RH4SU
8 VE-50051237 INST BOOK(CZ/POL/HUN/BU/RU) AV-28RH4BU
8 VE-50051255 INST BOOK(CZ/POL/HUN/BU/RU) AV-28RH4SU
9 BT-54013-2TK WARRANTY CARD
10 VE-20160975 LABEL AV-28RH4BU
10 VE-20160981 LABEL AV-28RH4SU




No. YA0777
Victor Company of Japan, Limited
AV & MULTIMEDIA COMPANY VIDEO DISPLAY CATEGORY 12, 3-chome, Moriya-cho, kanagawa-ku, Yokohama, kanagawa-prefecture, 221-8528, Japan

Printed in Japan
No. YA077 WPC
SERVICE MANUAL
COLOUR TELEVISION
3
2005
YA077B


AV-28RH4BU, AV-28RH4SU
Supplementary

The following items for the AV-28RH4BU and AV-28RH4SU were changed partly.
Therefore, this service manual describes only the items which differ from those of the AV-28RH4BU and AV-
28RH4SU service manual.
For details other than those described in this manual, please refer to the AV-28RH4BU and AV-28RH4SU
service manual (No.YA077, 2005/2).




DIFFERENCE LIST
PRINTED WIRING BOARD PARTS LIST
MAIN P.W. BOARD ASS'Y
Part No.
Ref. No. PART NAME DESCRIPTION
BEFORE AFTER
TU200 VE-30009637 VE-30033888 TUNER Non compatible


FEAUTER BOX P.W. BOARD ASS'Y
NOTE: Be sure to change IC752, when the TUNER is changed.
Part No.
Ref. No. PART NAME DESCRIPTION
BEFORE AFTER
IC752 VE-30013571 VE-20190399 IC Compatible




COPYRIGHT © 2005 Victor Company of Japan, Limited No.YA077B
2005/3
SECTION 1
PRECAUTION


Please refer to "AV-28RH4BU and AV-28RH4SU (No.YA077)" about this section.




SECTION 2
SPECIFIC SERVICE INSTRUCTIONS


Please refer to "AV-28RH4BU and AV-28RH4SU (No.YA077)" about this section.




SECTION 3
DISASSEMBLY


Please refer to "AV-28RH4BU and AV-28RH4SU (No.YA077)" about this section.




SECTION 4
ADJUSTMENT
4.1 SETTING VALUES OF VIDEO ITEMS
When a previous TUNER (VE-30009637) is replaced by a new 4.1.1 SETTING VALUE OF VIDEO ITEM
TUNER (VE-30033888), it should be adjusted to the setting Make sure not to change the values that are not in the table
values in the table below. If the TUNER of the model with the new below. If those values are changed, the unit will not operate
TUNER (VE-30033888) is replaced, there is no need for normally.
adjustment.
Setting value
Item
BEFORE AFTER
T_T THO SAM




1-2 (No.YA077B)
4.1.2 HOW TO ENTER THE SERVICE MODE
(1) Press the INFORMATION key and MUTING key REMOTE CONTROL UNIT key NAME
simultaneously, and the SERVICE MENU 1 screen will be
displayed. (Fig.1)
SERVICE MENU 1
PRODUCTION i >STORE MENU>EXIT MUTE key
H/V (FULL MODE) VIDEO
V-SHIFT *** WdR ***
V-SIZE **** WdG ***
H-SHIFT **** WdB ***
H-SIZE *** CuR ***
S-COR *** CuG ***
LINRT *** CuB ***
ANGLE *** G2Cu ***
BOW *** YDP ***
TRAPEZ
PARAB
***
***
AGC
APSW
***
***
colour key
U.COR
L.COR
***
***
APS
T_T
***
*** RED
TILT T_P ***
GREEN
***
TRPZD *** YDS ***
NTSCHS *** YDN ***
TXTV
HS04_3
***
***
EXT3
DVD
***
***
YELLOW
JVC52 ****
**.**.****
C.M
4:3
***
*** BLUE
SERVICE

Fig.1 TELETEXT key

4.1.3 HOW TO CHANGE THE SETTING VALUE UP / DOWN
(1) While the SERVICE MENU screen is displayed, press the [ ]/[ ] key
GREEN key to select the "VIDEO".
(2) Press the FUNCTION [ ]/[ ] key to select the "T_T".
(3) Press the FUNCTION [ ]/[ ] key to set the value to LEFT / RIGHT
"SAM". [ ]/[ ] key
(4) Press the [INFORMATION] key to memorize the set value.
SERVICE MENU 1
PRODUCTION i >STORE MENU>EXIT INFORMATION key
H/V (FULL MODE) VIDEO
MENU key
V-SHIFT *** WdR ***
V-SIZE **** WdG ***
H-SHIFT **** WdB ***
H-SIZE *** CuR ***
S-COR *** CuG ***
LINRT *** CuB ***
ANGLE *** G2Cu ***
BOW *** YDP ***
TRAPEZ *** AGC ***
PARAB
U.COR
***
***
APSW
APS
***
*** THO
L.COR *** T_T ***
TILT *** T_P ***
TRPZD *** YDS ***
NTSCHS *** YDN ***

SAM
TXTV *** EXT3 ***
HS04_3 *** DVD ***
JVC52 **** C.M ***
**.**.**** 4:3 ***
SERVICE

Fig.2




SECTION 5
TROUBLESHOOTING


Please refer to "AV-28RH4BU and AV-28RH4SU (No.YA077)" about this section.




(No.YA077B)1-3
Victor Company of Japan, Limited
AV & MULTIMEDIA COMPANY VIDEO DISPLAY CATEGORY 12, 3-chome, Moriya-cho, kanagawa-ku, Yokohama, kanagawa-prefecture, 221-8528, Japan

(No.YA077B)
Printed in Japan
VPT
AV-28RH4BU ENGLISH
FRANÇAIS
AV-28RH4SU DEUTSCH
ITALIANO
CASTELLANO
NEDERLANDS
PORTUGUÊS




COLOUR TELEVISION INSTRUCTIONS
TELEVISEUR COULEUR
VICTOR COMPANY OF JAPAN, LIMITED
MANUEL D'INSTRUCTIONS

FARBFERNSEHGERÄT BEDIENUNGSANLEITUNG

TELEVISORE A COLORI ISTRUZIONI

TELEVISOR A COLOR MANUAL DE INSTRUCCIONES

KLEURENTELEVISIE GEBRUIKSAANWIJZING

TELEVISOR A CORES INSTRUÇÕES




50051243
©2004 VICTOR COMPANY OF JAPAN, LIMITED
0504-JVC
Contents Safety Precautions
Safety Precautions ................................................... 1 1. Power Source
Remote Control Buttons .......................................... 2 The receiver should be operated only from a 220-240V AC,
50 Hz. outlet. Ensure you select the correct voltage setting
Control Panel Buttons .............................................. 3 for your convenience.
Antenna Connections ............................................... 3 2. Power Cord
Preparation ................................................................ 4 The power supply cord should be placed so that they are not
likely to be walked on or pinched by items placed upon them
Features .......................................................................... 4
or against them. Pay particular attention to cord where they
Before Switching on your TV .................................. 4 enter the plug, power outlet, and the point where they exit
Power connection ............................................................. 4 from the receiver.
Aerial Connections ........................................................... 4 3. Moisture and Water
How to connect the external equipments .......................... 4
Inserting batteries in the remote control handset .............. 4 Do not use this equipment in a humid and damp place (avoid
the bathroom, the sink in the kitchen, and near the washing
Switching the TV ON/OFF ........................................ 4 machine). Do not expose this equipment to rain or water and
To switch the TV on .......................................................... 4 do not place objects filled with liquids on it as this may be
To switch the TV off .......................................................... 4 dangerous.
Initial Settings ........................................................... 5 4. Cleaning
T-V LINK .......................................................................... 5 Before cleaning, unplug the receiver from the main supply
Operating with the onset buttons ...................................... 6 outlet. Do not use liquid or aerosol cleaners. Use with soft
Operating with Remote Control ......................................... 6 and dry cloth.
Menu System ............................................................. 7 5. Ventilation
Picture Menu ................................................................... 7 The slots and openings on the receiver are intended for venti-
Sound Menu ..................................................................... 7 lation and to ensure reliable operation. To prevent overheating,
Install (Installation) Menu.................................................. 8 these openings must not be blocked or covered in anyway.
Using the Decoder (EXT-2) function ................................. 10
Feature Menu .................................................................. 11
6. Lightning
Other Features ........................................................ 12 In case of storm and lightning or when going on holiday, dis-
connect the power cord from the wall outlet.
Sound Mute ....................................................................12
Stereo / Bilingual ............................................................. 12 7. Replacement Part
Information on Screen ..................................................... 12 When replacement parts are required, be sure the service
To Display the Time ......................................................... 12 technician has used replacement parts which are specified
Picture ............................................................................ 12 by the manufacturer or have the same specifications as the
VCR Control Buttons ....................................................... 12 original one. Unauthorized substitutions may result in fire,
Teletext .................................................................... 12 electrical shock, or other hazards.
To operate Teletext .......................................................... 12 8. Servicing
To select a page of Teletext ............................................. 12 Please refer all servicing to qualified personnel. Do not re-
To Select Index Page ...................................................... 12 move cover as this may result in electric shock.
Searching for a teletext page while watching TV ..............12 9. Flame sources
To Select Double Height Text .......................................... 13
To Reveal concealed Information ................................... 13 Do not place naked flame sources on the apparatus.
To Stop Automatic Page Change ..................................... 13 10. Stand-By
To Select a Subcode Page .............................................. 13 Do not leave your TV stand-by or operating condition when you
To exit Teletext ................................................................ 13 leave your house.
Fastext and Toptext ........................................................13
Warning!
Connect the External Equipments ........................ 14
Any intervention contrary to regulations, in particular, any
Via the Euroconnector ..................................................... 14 modification of high voltage or a replacement of the picture
T-V LINK compatible VCR ............................................... 14 tube may lead to an increased concentration of x-rays. Any
RGB mode ...................................................................... 14 television modified in this way no longer complies with license
EXT-2 S Mode ................................................................. 14 and must not be operated.
Via the RCA jacks ........................................................... 14
Instructions for waste disposal:
Via the ANT (aerial) socket .............................................. 14
TV and Video Recoder (VCR) .......................................... 14 Packaging and packaging aids are recyclable and should
NTSC Playback ..............................................................14 principally be recycled. Packaging materials, such as foil
Copy Facility ................................................................... 14 bag, must be kept away from children.
Connecting Headphones ................................................. 14 Batteries, including those which are heavy metal-free, should
Tips........................................................................... 16 not be disposed of with household waste. Please dispose of
used batteries in an environmentally sound manner. Find out
Specifications .......................................................... 16 about the legal regulations which apply in your area.


ENGLISH - 1 -
Remote Control Buttons

= Stand By / Power

0 - 9 = Direct Program
STANDARD Button (Picture Mode Change)
Colour Buttons
RED: Zoom (Picture Size) Change
GREEN: Hyper Sound
YELLOW: Factory Settings in Picture Menu

MENU = Menu Button
( ) = Cursor Up / Programme Up

( ) = Cursor Right / Volume +

Teletext Control Buttons
VCR Control Buttons
( ) = Cursor Down / Programme Down

( ) = Cursor Left / Volume -

AV = AV Button

= Information Button / T-V Link in Program Menu

= Mute




CAUTION
RISK OF ELECTRIC SHOCK

The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of
uninsulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk
of electric shock of persons.

The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating
and maintenance (servicing) instructions in the literature accompanying the appliance.




ENGLISH - 2 -
Control Panel Buttons



$95+%8
WvqrÃDÃ
Urvhy


$95+68
6qvÃDÃ
Urvhy




Crhqur




ASPIUÃ6W

@YU"



&21752/
3$1(/
%877216
Qr Hr
ÃQthÃ
ÃWyrÃ




Antenna Connections




ENGLISH - 3 -
Preparation Before Switching on your TV
Place TV on a solid surface. Power connection
For ventilation, leave a space of at least 10 cm free all around Important: The TV set is designed to operate on 220-240 V
the set. To prevent any fault and unsafe situations, please do AC, 50 Hz.
not place any objects on top of the set. After unpacking, allow the TV set to reach the ambient room
Use this apparatus in tropical and moderate climates. temperature before you connect the set to the mains.

Features Aerial Connections
Connect the aerial plug to the aerial input socket located at
It is a remote controlled colour television. the back of the TV.
100 programmes from VHF, UHF bands or cable channels How to connect the external equipments
can be preset.
See Connect the External Equipments on page 15.
It can tune cable channels.
See the instruction manuals provided with the external de-
Controlling the TV is very easy by its menu driven system. vices too.
It has two Euroconnector sockets for external devices (such Inserting batteries in the remote control handset
as video recorder, video games, audio set, etc.) Remove the battery cover located on the back of the hand-
Front AV (EXT-3) Input available. set by gently pulling upwards from the indicated part.
Stereo sound systems (German+Nicam) are available. Insert two AA (R6) or equivalent type batteries inside.
Full function Teletext (Fastext, Toptext). Replace the battery cover.
It is possible to connect headphone.
Direct channel access.
A.P.S. (Automatic Programming System).
All programmes can be named.
Forward or backward automatic tuning.
Sleep timer.
Child Lock.
Blue Background.
Comb Filter : Digital circuitry to make adjustments providing
outstanding picture quality with sharp, crisp edges, while vir- NOTE: Remove batteries from remote control handset when it is
tually eliminating dot crawl. not to be used for a long period. Otherwise it can be damaged
due to any leakage of batteries.
CTI : (Colour Transient Improvement) Improvement of hori-
zontal transitions of chrominance (colour) signals.
Switching the TV ON/OFF
T-V Link.
Automatic sound mute when no transmission. You can operate your TV either using the remote control
handset or directly using the TV onset buttons.
When no valid signal is detected, after 5 minutes the TV
switches itself automatically to stand-by mode. To switch the TV on
WSS (Wide Screen Signaling). Your TV will switch on in two steps:
NTSC Playback. 1- Press the power button located on the front of the TV. Then
the TV switches itself to standby mode and the RED LED
located below the TV turns on.
2- To switch on the TV from stand-by mode either:
Press a digit button on the remote control so that a program-
me number is selected,
or,
Press Standby / Power Button or Programme Up and Down
buttons on the TV or on the remote control respectively, so
the TV will switch on and the RED Led will turn GREEN.
IMPORTANT:
If no aerial signal is received at the selected program for a
period of 5 minutes then your TV automatically switches
into stand-by mode.
To switch the TV off
Press the stand-by button on the remote control, so the TV
will switch to stand-by mode and the GREEN LED will be-
come RED, or,
Press the power button located on the front of the TV.

ENGLISH - 4 -
NOTE: If you have switched of the TV set from the power but- The AUTOSTORE function automatically stores the re-
ton instead of the remote control, next time you press the ceived channels in your TV's programme numbers.
power button, the TV set will switch on without going to the
stand-by mode.
6QTÃ DTÃ SVIIDIBÃ QG@6 T@

Initial Settings X6DU



When the TV is first turned on. It enters the initial setting ÃÃÃÃÃÃÃÃ ThvÃÃÃ 8uhryÃÃÃ Ihr

IS
mode, and the AUTOSTORE menu is displayed. Follow the
instructions below to do the initial settings.



G6IBV6B@ÃÃ
6QTÃ DTÃ SVIIDIBÃ QG@6 T@
8PVIUS`ÃÃ X6DU

8vr
ÃÃÃÃÃÃÃÃ ThvÃÃÃ 8uhryÃÃÃ Ihr

IS




The AUTOSTORE menu does not appear when your TV has
been turned on once. In this case, use the LANGUAGE,
COUNTRY and AUTOSTORE items in the INSTALL APS: Automatic Programming System
menu to make the initial settings. For details, see Install After the AUTOSTORE is finalized, PROGRAM menu ap-
(Installation) Menu on page 8. pears. You can delete a channel or change a programme
If you want to do the initial settings later, press STAN- number. For details, see PROGRAM Menu on page 10.
DARD button to turn the menu off. QSPBS6H


1. Press " " or " " button to select "LANGUAGE" ÃÃÃÃ ÃÃÃÃ ! ÃÃÃÃ

item. Then press the or button to enter the "LAN- !
"
ÃÃÃÃ
ÃÃÃÃ
!
"
ÃÃÃÃ
ÃÃÃÃ
!!
!"
ÃÃÃÃ
ÃÃÃÃ

GUAGE" sub-menu. # ÃÃÃÃ # ÃÃÃÃ !# ÃÃÃÃ
$ ÃÃÃÃ $ ÃÃÃÃ !$ ÃÃÃÃ


/$1*8$*(
% ÃÃÃÃ % ÃÃÃÃ !% ÃÃÃÃ
& ÃÃÃÃ & ÃÃÃÃ !& ÃÃÃÃ
' ÃÃÃÃ ' ÃÃÃÃ !' ÃÃÃÃ
( ÃÃÃÃ ( ÃÃÃÃ !( ÃÃÃÃ

(QJOLVK ÃÃÃÃ ! ÃÃÃÃ " ÃÃÃÃ




'HXWVFK puhtr
qryrr

)UDQoDLV v UWÃGvx



(VSDxRO 8. If you do not have a T-V LINK compatible VCR, press
3RUWXJXHV STANDARD button to exit the menu.
If you have a T-V LINK compatible VCR connected to the
EXT-2 terminal, press button to display T-V LINK
2. Press " " or " " button to select a language. Then menu. Then follow the operating procedure Downloading
press the or button to store it. data to VCR in the following T-V LINK section.
3. Press the MENU button to return to the AUTOSTORE UWÃGvx
menu.
9yhqÃÃUWÃÃ ÃÃW8S
4. Press " " or " " button to select "COUNTRY" item.
Then press the or button to enter the "COUNTRY" 8vr Ã

sub-menu. TU9 8hpry



&28175< If a channel you want to view is not stored, store it using
the TUNING menu. For details, see Tuning Menu on
(QJODQG page 9.
,WDOLD
T-V LINK
1RUZD\
1HGHUODQG When a T-V LINK compatible VCR is connected to the EXT-2
3RUWXJDO Terminal on the TV, it is easier to set up the VCR and to view
videos. T-V LINK uses the following features:
To use T-V LINK functions:
5. Press " " or " " button to select the country where A T-V LINK compatible VCR means a JVC video cassette
you are now located. Then press the or button to recorder with the T-V LINK logo, or with one of the following
store it. logos. However, these VCRs may support some or all of the
features described earlier. For details, see your VCR instruc-
6. Press the MENU button to return to the AUTOSTORE
tion manual.
menu.
Q-LINK (a trademark of Panasonic Corporation)
7. Press or button to select Continue item.
Then press button to start the AUTOSTORE function. Data Logic (a trademark of Metz Corporation)

ENGLISH - 5 -
Easy Link (a trademark of Phillips Corporation) TV auto power on/VCR image view:
Megalogic (a trademark of Grundig Corporation) When the VCR starts playing, the TV automatically turns on
SMARTLINK (a trademark of Sony Corporation) and the images from EXT.2 (EXT-2) terminal appear on the
screen.
Downloading data to VCR:
This function does not happen if your TVs main power
The VCR will automatically download the registered data on is turned off. Set your TVs main power to on (standby
the TV channels from the TV. This means you do not need to mode).
set up the programme channels on your VCR manually.
The T-V LINK menu will be displayed when you press the Operating with the onset buttons
button while PROGRAM menu is displayed, or when- Volume setting and programme selection can be made using
ever the INSTALL menu operations are performed. the buttons on the right side of the TV.
UWÃGvx Volume Setting:
9yhqÃÃUWÃÃ ÃÃW8S Press - button to decrease volume or + button to
increase volume, so a volume level scale will be displayed
8vr Ã
on the screen.
TU9 8hpry

Programme Selecting:
Press button to start downloading data to VCR.
Press P/Ch+ button to select next programme or P/Ch-
If you do not want to do, press the STANDARD button to button to select the previous programme.
exit the menu.
Entering Main Menu:
Press MENU button to enter main menu. In the main
menu select submenu using P/Ch+ or P/Ch- button and
enter the submenu using + or - button. To learn
the usage of the menus, refer to the Menu System section
When FEATURE NOT AVAILABLE is displayed: of this manual.
If FEATURE NOT AVAILABLE is displayed, the download
was not performed correctly. Before trying to download again, Operating with Remote Control
check that: The remote control handset of your TV is designed to control
The VCR power is turned on all the functions of the model you selected. The functions will
The VCR is T-V LINK compatible be described in accordance with the menu system of your
TV.
The VCR is connected to the EXT-2 terminal
Functions which you can use out of menu system are de-
The SCART cable is fully wired.
scribed below.
Direct Rec: Volume Setting:
What You See Is What You Record
Press button to increase volume.
You can easy record to VCR the images that you are watch-
ing on the TV. For details, read the manual for your VCR, Use Press button to decrease volume.
your VCR controls. You cannot carryout Direct Rec using
Programme Selecting (Previous or next programme):
your TVs control.
UWÃGvx
Press button to select the previous programme.
Press button to select the next programme.
W8SÃvÃSrpqvt




When the VCR is not ready (for example when there is no
tape inserted), NO RECORDING is displayed.
In the following situations, the VCR will stop recording if the
TV is turned off, if the TV channel or input is changed, or if
the menu is displayed on the TV:
Programme Selecting (direct access):
When recording images from an external device connected
to the TV. (for example a camcorder) Press digit buttons on the remote control handset to select
When recording a TV channel after it has been unscrambled programmes between 0 and 9. TV will switch to the selected
on a decoder. program after a short delay.
When recording a TV channel by using the TVs output be- For a two or three digit program number enter the second or
cause the VCRs own tuner cannot properly receive that third digit after pressing the first digit within 2 seconds.
channel.




ENGLISH - 6 -
Menu System You can change the Contrast by or button after se-
lecting this item.
Your TV has been designed with a menu system. Display
MENU (main menu) and enter one of four menus (PICTURE,
SOUND, INSTALL and FEATURE). You can change Colour only when Picture Mode is selected
1- Press MENU button to display MENU (main menu). The User.
menu titles will be displayed in the main menu. You can change the Colour by or button after select-
2- Press or button to select a menu title, then ing this item.
press or button to enter the menu.
To exit a menu, press STANDARD button.
You can change the Sharpness by or button after
To go to the previous menu, press MENU button. selecting this item.
Picture Menu
To change picture settings: You can adjust the Colour Temp item as Normal, Warm
and Cool. Using or button toggle between these
Press MENU button, now you are in main menu. In the three settings.
main menu, select PICTURE using or button,
then enter the picture menu pressing or button. QD8UVS@




8y


Tuhr


8yÃUr


IvrÃrqpv


a




Note: When Picture Mode is not USER, BRIGHTNESS, The Noise reduction can be adjusted in four different lev-
CONTRAST and COLOUR options can not be reached by els: Minumum, Medium, Maximum and Auto. Addition-
or buttons. ally it can be cancelled by selecting the OFF option. Press-
Factory Settings: ing or button toggles between these five settings.

In the Picture Menu if you press the YELLOW button the ad-
justmens switches themselves to the factory settings. The Zoom can be three different modes: Auto, 4:3 or 16:9
You can change the values of this items firstly by selecting modes. Using or button toggle between these differ-
the item by or button and then by using or ent screen formats.
button. The PICTURE menu disappears and level indica- The Picture Mode can be stored for all channels (200 chan-
tors are displayed while items are changed. The PICTURE nels) individually.
menu is restored after adjustment is finished. It is also possible to change picture modes directly by press-
This item is used to change the picture mode. By pressing ing ZOOM button (RED button) on your remote control.
or button you may choose one of these options:
Bright, Standard, Soft, User.
QD8UVS@
You can change the Hue for NTSC 3.58/4.43 systems by
or button after selecting this item. A level indicator for
QvprÃHqr Hue is displayed while changing this item. The Hue bar is
7vtur
displayed while an NTSC signal is input from the EXT-1,
EXT-2, or EXT-3 (Front AV) terminal.
8h


8y


Tuhr
Recalling Factory settings.:
You can re-set the current PICTURE menu settings (except
Noise Reduction and Colour Temp settings) to the default
You can change Brightness only when Picture Mode is se- settings.
lected User. Press STANDARD button when no menu appears.
You can change the Brightness by or button after
selecting this item. Sound Menu
To change sound settings:
You can change Contrast only when Picture Mode is select- Press MENU button, now you are in main menu. In the
ed User. main menu, select SOUND using or button,
then enter the sound menu pressing or button.


ENGLISH - 7 -
Hyper Sound can be set On or Off also by GREEN button.
Stereo Mode:
You can use this feature to switch the broadcasting languge
the dubbed or original language. Some TV channels broad-
casts the programmes in two languages. If the TV channel
Setting Volume: you are watching broadcasts in two languages (e.g. Euro-
sport), you can select the dubbed or original language by set-
Using or button to select Volume. ting this item to DUAL I or DUAL II by pressing or but-
Press button to increase volume. ton. the other options of this item are MONO and STEREO
(NICAM STEREO).
Press button to decrease volume.
If the stereo broadcast is received poorly, you can change
6281' this item from Stereo to mono sound so that you can hear the
broadcast more clearly and easily.
9ROXPH
%DODQFH
%DVV Install (Installation) Menu
7UHEOH Press MENU button, now you are in main menu. In the
main menu, select INSTALL, using or button.
Then enter the INSTALL menu pressing or button.

Setting Balance:
Using or button select Balance.
Press button to change balance rightward.
Press button to change balance leftward.


Setting Bass Level:
Using or button select Bass. Menu Language Selection:
Press button to increase bass level.
Press the or button to select LANGUAGE
Press button to decrease bass level. item.
Press or button to enter LANGUAGE sub-menu.
/$1*8$*(
Setting Treble Level:
Using or button select Treble. (QJOLVK
Press button to increase treble level. 'HXWVFK
)UDQoDLV
Press button to decrease treble level.
(VSDxRO
TPVI9
3RUWXJXHV

7h


Uriyr Press or button to select the desired menu lan-
CrÃTq
guage:
TrrÃHqr
After selecting the menu language press or button to
store the selected language.
Press MENU button to return to the INSTALL menu, or
Press STANDARD button to exit the menu.
Hyper Sound: Country Selection:
You can use this feature to switch on or off Hyper Sound. Press the or button to select the COUNTRY
Pressing or button will turn on or off this feature. If the item.
current sound system is MONO and the Hyper Sound is set Press or button to enter the COUNTRY sub-menu.
ON, then the sound will be heard as if it is STEREO. If the
current sound system is STEREO, switching Hyper Sound on
will make the sound deeper. Switching it off will make no
change in MONO and STEREO.


ENGLISH - 8 -
&28175<

(QJODQG UWÃGvx

,WDOLD 9yhqÃÃUWÃÃ ÃÃW8SÃArhr

1RUZD\
8vr Ã
1HGHUODQG
TU9 8hpry
3RUWXJDO
4. If you do not have a T-V LINK compatible VCR, press
STANDARD button to exit the menu.
If you have a T-V LINK compatible VCR connected to the
Press or button to select the country where EXT-2 terminal, follow the operating procedure Down-
you are now located. loading the data to VCR on page 6 to transmit the Pro-
After selecting the country, press or button to store gramme table data to the VCR.
the selected country.
Search:
Press MENU button to return to the INSTALL menu, or
Press STANDARD button to exit the menu. You can search a channel manually.
Select "Search" item. Then press or button to start
Tuning Menu:
searching. "SEARCHING" is displayed while the TV is
You can store a channel manually, or modify the current set- searching a channel.
tings of a channel (for example, changing the channel name). Searching stops when the TV finds a channel. Then the
In an AV mode, you can change only the MODE or CO- channel is displayed.
LOUR SYSTEM setting. Press or button repeatedly until the channel you want
If you want to modify the current settings of a channel, se- appears.
lect the channel of which you want to modify the setting. When you cannot search a channel you want, select the
Then display the main menu on the scree