Text preview for : Sony-XM604M caramp.pdf part of Sony XM604M car amplifier
Back to : Sony-XM604M caramp.pdf | Home
XM-604M
SERVICE MANUAL
Ver. 1.0 2006. 10
US Model Canadian Model AEP Model UK Model E Model
AUDIO POWER SPECIFICATIONS POWER OUTPUT AND TOTAL HARMONIC DISTORTION 55 watts per channel minimum continuous average power into 4 ohms, both channels driven from 20 Hz to 20 kHz with no more than 0.04% total harmonic distortion per Car Audio Ad Hoc Committee standards.
SPECIFICATIONS
OTL (output transformerless) circuit Pulse power supply Inputs RCA pin jacks High level input connector Input level adjustment range 0.3 6 V (RCA pin jacks), 2.8 12 V (High level input) Outputs Speaker terminals Speaker impedance 2 8 (stereo) 4 8 (when used as a bridging amplifier) Maximum output 4 speakers: 110 W × 4 (at 4 ) 3 speakers: 150 W × 2 (at 2 ) + 300 W × 1 (BTL, at 4 ) Rated output (supply voltage at 14.4 V) 4 speakers: 60 W × 4 (20 Hz 20 kHz, 1% THD+N, at 4 ) 70 W × 4 (20 Hz 20 kHz, 1% THD+N, at 2 ) Frequency response 5 Hz 50 kHz ( +0 dB) 3 Harmonic distortion 0.005% or less (at 1 kHz, 4 ) Low-pass filter 80 Hz, 18 dB/oct High-pass filter 80 Hz, 12 dB/oct Power requirements 12 V DC marine battery (negative ground) Power supply voltage 10.5 16 V Current drain at rated output : 33 A (4 , 60 W × 4) Remote input : 1 mA Dimensions Approx. 401 × 55 × 264 mm (15 7/8 × 2 1/4 × 10 1/2 in) (w/h/d) not incl. projecting parts and controls Mass Approx. 3.2 kg (7 lb 1 oz) not incl. accessories Supplied accessories Mounting screws (4) High level input cord (1) Protection cap (1) Design and specifications are subject to change without notice. Circuit system
STEREO POWER AMPLIFIER
9-887-453-01
2006J04-1 © 2006. 10
Sony Corporation
eVehicle Division Published by Sony Techno Create Corporation
1
XM-604M
PROTECTOR OPERATION CHECK
Thermal Protect 1. Short across TH901 with the power on. 2. Verify that the protector is operated and D918 illuminates red. 3. Verify that the protector is released and D918 illuminates green when the short is removed. 4. Likewise, perform items 1 to 3 for TH902 and TH903. Over Current Protect 1. Short between the positive and negative sides of the speaker output terminals CN903 and CN904 with the power on. (Perform this shorting for each channel on FRONT and REAR.) 2. Verify that the protector is operated and D918 illuminates red. 3. Verify that the protector is not released and D918 remains red even when the short is removed. 4. Verify that the protector is released and D918 illuminates green when the power is turned off and then on again. Offset Protect 1. Short between the +12V terminal of CN904 and the (L+R) + or (L+R) of the speaker output terminal CN904. (Short between +12V terminal and (L+R) + and between +12V terminal and (L+R) .) 2. Verify that the protector is operated and D918 illuminates red. 3. Verify that the protector is not released and D918 remains red even when the short is removed. 4. Verify that the protector is released and D918 illuminates green when the power is turned off and then on again.
TABLE OF CONTENTS 1. GENERAL
Location and Function of Controls .......................................... 3 Connections ............................................................................. 4
2. DISASSEMBLY
2-1. Bottom Plate ........................................................................ 6 2-2. Main Board Section ............................................................ 7 2-3. Front Panel .......................................................................... 7
3. DIAGRAMS
3-1. 3-2. 3-3. 3-4. Block Diagram .................................................................... 9 Printed Wiring Board ........................................................ 10 Schematic Diagram Main Section (1/2) ........................ 11 Schematic Diagram Main Section (2/2) ........................ 12
4. EXPLODED VIEWS
4-1. Heat Sink (Main) Section .................................................. 13 4-2. Main Board Section .......................................................... 14
5. ELECTRICAL PARTS LIST ........................................ 15
UNLEADED SOLDER
Boards requiring use of unleaded solder are printed with the lead free mark (LF) indicating the solder contains no lead. (Caution: Some printed circuit boards may not come printed with the lead free mark due to their particular size.)
: LEAD FREE MARK
Unleaded solder has the following characteristics. · Unleaded solder melts at a temperature about 40°C higher than ordinary solder. Ordinary soldering irons can be used but the iron tip has to be applied to the solder joint for a slightly longer time. Soldering irons using a temperature regulator should be set to about 350°C. Caution: The printed pattern (copper foil) may peel away if the heated tip is applied for too long, so be careful! · Strong viscosity Unleaded solder is more viscous (sticky, less prone to flow) than ordinary solder so use caution not to let solder bridges occur such as on IC pins, etc. · Usable with ordinary solder It is best to use only unleaded solder but unleaded solder may also be added to ordinary solder.
SAFETY-RELATED COMPONENT WARNING!! COMPONENTS IDENTIFIED BY MARK 0 OR DOTTED LINE WITH MARK 0 ON THE SCHEMATIC DIAGRAMS AND IN THE PARTS LIST ARE CRITICAL TO SAFE OPERATION. REPLACE THESE COMPONENTS WITH SONY PARTS WHOSE PART NUMBERS APPEAR AS SHOWN IN THIS MANUAL OR IN SUPPLEMENTS PUBLISHED BY SONY.
Notes on Chip Component Replacement · Never reuse a disconnected chip component. · Notice that the minus side of a tantalum capacitor may be damaged by heat.
ATTENTION AU COMPOSANT AYANT RAPPORT À LA SÉCURITÉ!! LES COMPOSANTS IDENTIFIÉS PAR UNE MARQUE 0 SUR LES DIAGRAMMES SCHÉMATIQUES ET LA LISTE DES PIÈCES SONT CRITIQUES POUR LA SÉCURITÉ DE FONCTIONNEMENT. NE REMPLACER CES COMPOSANTS QUE PAR DES PIÈCES SONY DONT LES NUMÉROS SONT DONNÉS DANS CE MANUEL OU DANS LES SUPPLÉMENTS PUBLIÉS PAR SONY.
2
XM-604M SECTION 1 GENERAL
Location and Function of Controls
1 POWER/PROTECTOR indicator Lights up in green during operation. When the PROTECTOR is activated the indicator will change from green to red. When the PROTECTOR is activated refer to the Troubleshooting Guide. 2 LEVEL adjustment control The input level can be adjusted with this control. Turn it in the clockwise direction when the output level of the marine audio unit seems low. 3 HPF switch When the HPF switch is set to ON, the Highpass filter (80 Hz) is effective. 4 LPF switch When the LPF switch is set to ON, the Lowpass filter (80 Hz) is effective.
This section is extracted from instruction manual.
Emplacement et fonction des commandes
1 Indicateur POWER/PROTECTOR S'allume en vert lors du fonctionnement de l'appareil. Lorsque PROTECTOR est activé, l'indicateur passe du vert au rouge. Lorsque PROTECTOR est activé, reportezvous au Guide de dépannage. 2 Commande de réglage LEVEL Le niveau d'entrée peut se régler avec cette commande. Tournez cette commande dans le sens des aiguilles d'une montre lorsque le niveau de sortie du lecteur audio marin semble faible. 3 Commutateur HPF Lorsque le commutateur HPF est réglé sur ON, le filtre passe-haut (80 Hz) est activé. 4 Commutateur LPF Lorsque le commutateur LPF est réglé sur ON, le filtre passe-bas (80 Hz) est activé.
Precautions
· This unit is designed for negative ground 12 V DC operation only. · Use speakers with an impedance of 2 to 8 (4 to 8 when used as a bridging amplifier). · Do not connect any active speakers (with builtin amplifiers) to the speaker terminals of the unit. Doing so may damage the active speakers. · If your boat is moored in direct sunlight and there is a considerable rise in temperature inside the boat, allow the unit to cool down before use. · When installing the unit horizontally, be sure not to cover the fins with the floor carpet etc. · If this unit is placed too close to the marine audio unit or antenna, interference may occur. In this case, relocate the amplifier away from the marine audio unit or antenna. · If no power is being supplied to the marine audio unit, check the connections. · This power amplifier employs a protection circuit* to protect the transistors and speakers if the amplifier malfunctions. Do not attempt to test the protection circuits by covering the heat sink or connecting improper loads. · Do not use the unit on a weak battery as its optimum performance depends on a good power supply. · For safety reasons, keep your marine audio unit volume moderate so that you can still hear sounds outside your boat.
Fuse Replacement
If the fuse blows, check the power connection and replace both the fuses. If the fuse blows again after replacement, there may be an internal malfunction. In such a case, consult your nearest Sony dealer.
Warning
When replacing the fuse, be sure to use one matching the amperage stated above the fuse holder. Never use a fuse with an amperage rating exceeding the one supplied with the unit as this could damage the unit.
HPF (80Hz)
POWER/ PROTECTOR
OFF
2 4 6 0.3V 1 ON 0.5
LPF(80Hz)
OFF
2 4 6 0.3V 1 ON 0.5
LEVEL
LEVEL
FRONT
REAR
* Protection circuit This amplifier is provided with a protection circuit that operates in the following cases: -- when the unit is overheated -- when a DC current is generated -- when the speaker terminals are short-circuited. The color of the POWER/PROTECTOR indicator will change from green to red, and the unit will shut down. If this happens, turn off the connected equipment, take out the cassette tape or disc, and determine the cause of the malfunction. If the amplifier has overheated, wait until the unit cools down before use.
If you have any questions or problems concerning your unit that are not covered in this manual, please consult your nearest Sony dealer.
Précautions
· Cet appareil est conçu pour fonctionner uniquement sur un courant de 12 V CC avec masse négative. · Utilisez des haut-parleurs d'une impédance appropriée de 2 à 8 (stéréo), 4 à 8 (en cas d'utilisation comme amplificateur en pont). · Ne raccordez pas de haut-parleurs actifs (avec amplificateurs intégrés) aux bornes des hautparleurs de cet appareil. Cela risquerait en effet d'endommager les haut-parleurs actifs. · Lorsque votre bateau est amarré en plein soleil et que la température a augmenté de façon considérable, laissez refroidir l'appareil avant de l'utiliser. · Si vous installez l'appareil à l'horizontale, ne recouvrez pas les ailettes de ventilation avec le tapis de sol ou quoi que ce soit d'autre. · Si cet appareil est placé trop près du lecteur audio marin ou de l'antenne, il se peut que des interférences se produisent. Dans ce cas, éloignez l'amplificateur du lecteur audio marin ou de l'antenne. · Si le lecteur audio marin n'est pas alimenté, vérifiez les connexions. · Cet amplificateur de puissance est équipé d'un circuit de protection* conçu pour protéger les transistors et les haut-parleurs en cas de défaillance de l'amplificateur. N'essayez pas de tester l'efficacité des circuits de protection en recouvrant le dissipateur thermique ou en effectuant de mauvaises connexions. · N'utilisez pas l'appareil avec une batterie faible, car sa performance optimale dépend d'une bonne alimentation en électricité. · Pour des raisons de sécurité, maintenez le volume du lecteur audio marin à un niveau modéré afin d'entendre les bruits extérieurs.
Remplacement du fusible
Si le fusible fond, vérifiez les connexions de l'alimentation et remplacez les deux fusibles. Si le fusible fond de nouveau après avoir été remplacé, cela peut révéler une défaillance interne de l'appareil. Dans ce cas, consultez votre détaillant Sony le plus proche.
Avertissement
Lorsque vous remplacez le fusible, veillez à utiliser un fusible dont la capacité en ampères correspond à celle inscrite sur le porte-fusible. N'utilisez jamais de fusible dont la capacité dépasse celle du fusible fourni avec l'appareil car cela pourrait endommager l'appareil.
* Circuit de protection Cet amplificateur est fourni avec un circuit de protection qui entre en fonction dans les cas suivants : -- lorsque l'appareil est en surchauffe ; -- lorsqu'un courant continu est généré ; -- lorsque les bornes de haut-parleur sont courtcircuitées. La couleur de l'indicateur POWER/PROTECTOR passe du vert au rouge et l'appareil se met hors tension. Dans ce cas, éteignez les appareils raccordés, retirez la cassette ou le disque et déterminez l'origine du problème. Si l'amplificateur est en surchauffe, attendez qu'il refroidisse avant d'utiliser l'appareil.
Si vous avez des questions ou des problèmes concernant votre appareil qui ne sont pas abordés dans ce mode d'emploi, adressez-vous à votre détaillant Sony le plus proche.
3
XM-604M
Connections
Installation
Before Installation
· Mount the unit either inside a boatwall or the cabin. · Choose the installation location carefully so that the unit will not interfere with normal sailing operations. · Do not install the unit under the floor carpet, where the heat dissipation from the unit will be considerably impaired. · Avoid installing the unit in areas subject to: -- high temperatures such as from direct sunlight or hot air from the heater -- rain, sea water or moisture -- dust or dirt. · This unit is not waterproof. Install the unit where sea or rain water cannot enter the unit. If you install the unit in such a place, ensure that it is adequately waterproofed. First, place the unit where you plan to install it, and mark the positions of the 4 screw holes on the mounting board (not supplied). Then drill a 3 mm ( 1/ 8 in) pilot hole at each mark and mount the unit onto the board with the supplied mounting screws. The mounting screws are all 15 mm (19/ 32 in) long, so make sure that the mounting board is thicker than 15 mm ( 19/ 32 in). Before drilling and making holes, make sure that the mounting holes will not damage the fuel tank, fuel lines, electrical wiring, or body of the boat.
Installation
Avant l'installation
· Montez l'appareil à l'intérieur de la paroi mur du bateau ou dans la cabine. · Choisissez soigneusement l'emplacement d'installation afin que l'appareil ne gêne pas la navigation. · N'installez pas l'appareil sous le tapis de sol car la dissipation thermique ne pourrait pas se faire correctement. · N'installez pas l'appareil dans des endroits soumis : -- à des températures élevées, comme en plein soleil ou près du chauffage ; -- à la pluie, à l'eau de mer ou à l'humidité ; -- à la poussière ou à la saleté. · Cet appareil n'est pas étanche. Installez l'appareil dans un endroit protégé contre l'eau de mer et l'eau de pluie. Si vous installez l'appareil dans un endroit susceptible d'être exposé à l'eau, vérifi ez qu'il est bien protégé. Posez d'abord l'appareil à l'endroit où vous souhaitez l'installer et tracez un repère de positionnement pour les 4 orifices de vis sur la plaque de montage (non fournie). Percez des orifices de 3 mm (1/ 8 po) au niveau de chaque repère et fixez l'appareil sur la plaque avec les vis de montage fournies. La longueur des vis de montage est de 15 mm ( 19/ 32 po). Assurez-vous donc que l'épaisseur de la plaque de montage est supérieure à 15 mm (19/ 32 po). Avant de percer les trous de montage de l'appareil, assurez-vous que ces derniers n'endommageront pas le réservoir de carburant, les tuyaux d'alimentation en carburant, le câblage électrique ou la coque du bateau.
Make the terminal connections as illustrated below. Effectuez les connexions des bornes comme illustré ci-dessous.
REM
+12V
GND
3
3
REM
+12V
GND
c
Pass the wires through the cap, connect the wires, then cover the terminals with the cap.
Note When you tighten the screw, be careful not to apply too much torque * as doing so may damage the screw. * The torque value should be less than 1 N·m.
Faites passer les fils par le cache, raccordez les fils, puis recouvrez les bornes avec le cache.
Remarque Lorsque vous vissez la vis, faites attention à ne pas appliquer une trop grande force *, car cela pourrait endommager la vis. * Le couple de serrage doit être inférieur à 1 N·m.
Power Connection Wires (not supplied) Câbles d'alimentation (non fournis)
to a metal point of the boat vers un point métallique du bateau
Remote output *1 Sortie de télécommande *1 (REM)
Marine audio unit Lecteur audio marin
less than 450 mm (18 in) moins de 450 mm (18 po)
*2
Fuse (50 A) Fusible (50 A) +12 V marine battery Batterie de bateau +12 V
Mount the unit as illustrated. Montez l'appareil comme illustré.
1
*1 If you have the factory original or some other marine audio unit without a remote output for the amplifier, connect the remote input terminal (REMOTE) to the accessory power supply. In High level input connection, marine audio unit can also be activated without need for REMOTE connection. However, this function is not guaranteed for all marine audio units. *1 Si vous disposez du lecteur audio marin d'origine ou d'un autre lecteur audio marin dont l'amplificateur ne comporte pas de sortie de télécommande à distance, raccordez la borne d'entrée de commande à distance (REMOTE) à la prise d'alimentation accessoires. Dans une connexion d'entrée à haut niveau, le lecteur audio marin peut également être activé sans raccordement à REMOTE. Toutefois, cette fonction n'est pas garantie pour tous les lecteurs audio marins.
Notes on the power supply
Remarques sur l'alimentation électrique
· Raccordez le câble d'alimentation +12 V uniquement après avoir réalisé toutes les autres connexions. · Raccordez solidement le fil de masse de l'appareil à un point métallique du bateau. Une connexion lâche risque de provoquer un problème de fonctionnement de l'amplificateur. · Veillez à raccorder le fil de commande à distance du lecteur audio marin à la borne de commande à distance. · Si vous utilisez un lecteur audio marin dont l'amplificateur ne comporte pas de sortie de commande à distance, raccordez la borne d'entrée de commande à distance (REMOTE) à la prise d'alimentation accessoires. · Utilisez un câble d'alimentation doté d'un fusible (50 A). · Tous les fils électriques raccordés à la borne positive de la batterie doivent être protégés par un fusible à une distance maximum de 450 mm (18 po) à la borne de la batterie et avant de passer dans une partie métallique quelconque. · Assurez-vous que les fils de la batterie du bateau raccordés à ce dernier (sol au châssis)*2 sont d'un calibre au moins égal à celui du fil électrique principal reliant la batterie et l'amplificateur. · Pendant une utilisation à pleine puissance, un courant d'une intensité supérieure à 50 A circule dans le système. Assurez-vous que les câbles à raccorder aux bornes +12 V et GND de cet appareil sont de calibre supérieur à 10 (AWG-10) ou d'une section supérieure à 5 mm 2 ( 7/32 po 2).
Cautions
· Before making any connections, disconnect the ground terminal of the marine battery to avoid short circuits. · Be sure to use speakers with an adequate power rating. If you use small capacity speakers, they may be damaged. · This is a Phase-Inverted Amplifier. · Do not connect the # terminal of the speaker system to the frame of the boat, and do not connect the # terminal of the right speaker with that of the left speaker. · Install the input and output cords away from the power supply wire as running them close together can generate some interference noise. · This unit is a high powered amplifier. Therefore, it may not perform to its full potential if used with the speaker cords supplied with the boat. · If your boat is equipped with a computer system for navigation or some other purpose, do not remove the ground wire from the marine battery. If you disconnect the wire, the computer memory may be erased. To avoid short circuits when making connections, disconnect the +12 V power supply wire until all the other wires have been connected.
Avertissement
· Avant d'effectuer les raccordements, débranchez la borne de masse de la batterie de voiture pour éviter de provoquer un courtcircuit. · Utilisez des haut-parleurs d'une capacité adéquate. Si vous utilisez des haut-parleurs de faible capacité, ils risquent d'être endommagés. · Les phases de cet amplificateur sont inversées. · Ne raccordez pas la borne # du système de haut-parleurs à la carrosserie de la voiture, ou la borne # du haut-parleur droit à celle du haut-parleur gauche. · Éloignez les cordons d'entrée et de sortie du fil d'alimentation électrique afin d'éviter que des interférences ne se produisent. · Cet appareil est un amplificateur de haute puissance. Il se peut donc qu'il n'atteigne pas sa puissance maximale s'il est utilisé avec les cordons de haut-parleurs de la voiture. · Si votre voiture est équipée d'un ordinateur de bord pour la navigation ou autre, ne débranchez pas le fil de masse de la batterie de la voiture. Si vous débranchez ce fil, toute la mémoire de l'ordinateur risque d'être effacée. Pour éviter tout risque de court-circuit lorsque vous effectuez les raccordements, branchez le fil d'alimentation de +12 V uniquement après avoir branché tous les autres fils.
· Connect the +12 V power supply wire only after all the other wires have been connected. · Be sure to connect the ground wire of the unit securely to a metal point of the boat. A loose connection may cause a malfunction of the amplifier. · Be sure to connect the remote control wire of the marine audio unit to the remote terminal. · When using a marine audio unit without a remote output on the amplifier, connect the remote input terminal (REMOTE) to the accessory power supply. · Use a power supply wire with a fuse attached (50 A). · All power wires connected to the positive battery post should be fused within 450 mm (18 in) of the battery post, and before they pass through any metal. · Make sure that the boat's battery wires connected to the boat (ground to frame) *2 are of a wire gauge at least equal to that of the main power wire connected from the battery to the amplifier. · During full-power operation, a current of more than 50 A will run through the system. Therefore, make sure that the wires to be connected to the +12 V and GND terminals of this unit are at least 10-Gauge (AWG-10) or have a sectional area of more than 5 mm 2 ( 7/32 in 2).
4
XM-604M
Input Connections/Connexions d'entrée
Speaker Connections
Turn on or off the LPF and HPF switch at the unit rear as illustrated below.
A
Line Input Connection Connexion d'entrée de ligne
Conexións des haut-parleurs
Réglez le commutateur LPF et HPF situé à l'arrière de l'appareil à On ou Off, comme indiqué dans l'illustration ci-dessous.
Marine audio unit Lecteur audio marin
1
Rear Arrière
4-Speaker System Système à 4 haut-parleurs
Front speaker (min. 2 ) Haut-parleurs avant (min. 2 )
LINE OUT
Front Avant
LINE OUT
Left gauche
Right droit
HPF (80Hz)
OFF ON
LPF(80Hz)
OFF ON
B
High Level Input Connection Connexion d'entrée à haut niveau
Left gauche
Right droit
Rear speaker (min. 2 ) Haut-parleurs arrière (min. 2 ) Front right speaker output Sortie du haut-parleur avant droit Gray Gris Striped Rayé White Blanc Front left speaker output Sortie du haut-parleur avant gauche Rear left speaker output Sortie du haut-parleur arrière gauche Rear right speaker output Sortie du haut-parleur arrière droit Purple Mauve Striped Rayé Green vert Striped Rayé Left gauche
2
3-Speaker System Système à 3 haut-parleurs
Marine audio unit Lecteur audio marin
Full range speakers (min. 2 ) Hauts-parleurs pleine gamme (min. 2 )
Right droit
HPF (80Hz)
OFF ON
LPF(80Hz)
OFF ON
Striped Rayé
2
L R
Subwoofer (min. 4 ) Caisson de graves (min. 4 )
High Level Input Connector Connecteur d'entrée à haut niveau
Gray Gris White Blanc Green Vert
Notes · In this system, the volume of the subwoofer will be controlled by the marine audio unit fader control. · In this system, the output signals to the subwoofer will be the combination of both the REAR L and R INPUT jacks or the REAR high level input connector signals. Remarques · Dans ce système, le volume du caisson de graves est contrôlé par la commande de balance avant/arrière du lecteur audio marin. · Dans ce système, les signaux émis vers le caisson de graves sont constitués des signaux des prises REAR L et R INPUT ou des signaux du connecteur d'entrée de haut niveau REAR.
FRONT
REAR
Purple Mauve
Striped/White Rayé blanc Striped/Gray Rayé gris
L R
L R
Striped/Purple Rayé mauve
3
2-Way System Système 2 voies
Full range speakers (min. 2 ) Hauts-parleurs pleine gamme (min. 2 )
Striped/Green Rayé vert
Left gauche
Right droit
HPF (80Hz)
OFF ON
LPF(80Hz)
OFF ON
Left gauche
Right droit
Subwoofer (min. 2 ) Caisson de graves (min. 2 )
Note In this system, the volume of the subwoofer will be controlled by the marine audio unit fader control. Remarque Dans ce système, le volume du caisson de graves est contrôlé par la commande de balance avant/arrière du lecteur audio marin.
5
XM-604M SECTION 2 DISASSEMBLY
Note : This set can be disassemble according to the following sequence.
SET 2-1. BOTTOM PLATE (Page 6) MAIN BOARD SECTION (Page 7) FRONT PANEL (Page 7)
2-2.
2-3.
Note : Follow the disassembly procedure in the numerical order given.
2-1. BOTTOM PLATE
2 four screws (+BTP 3 × 6) 1 three screws (+BTP 3 × 6)
3 bottom plate
6
XM-604M
2-2. MAIN BOARD SECTION
3 three screws (+P 3 × 8)
4 screw (+BTP 3 × 6) 2 three screws (+P 3 × 8)
1 three screws (+P 3 × 8)
5 MAIN board section
heat sink (main)
2-3. FRONT PANEL
5 MAIN board
4 front panel
3 screw (+P 3 × 8)
2 screw (+P 3 × 8)
1 three screws (+P 3 × 8)
7
XM-604M SECTION 3 DIAGRAMS
THIS NOTE IS COMMON FOR PRINTED WIRING BOARDS AND SCHEMATIC DIAGRAMS. (In addition to this, the necessary note is printed in each block.) for schematic diagram: · All capacitors are in µF unless otherwise noted. (p: pF) 50 WV or less are not indicated except for electrolytics and tantalums. · All resistors are in and 1/4 W or less unless otherwise specified. Note: The components identified by mark 0 or dotted line with mark 0 are critical for safety. Replace only with part number specified. Note: Les composants identifiés par une marque 0 sont critiques pour la sécurité. Ne les remplacer que par une piéce portant le numéro spécifié.
NOTE FOR REPLACEMENT OF THE TRANSISTORS:
The transistors Q110, 111, 210, 211, 310, 311, 410 and 411 have two different ranks: P rank and Y rank. The rank of these transistors need to be selected properly according to each channel. When replacing any one of these transistors, check its rank and replace with the appropriate transistor of the same rank. Rank P Y Q110, 210, 310, 410 2SC5100-P (8-729-024-79) 2SC5100-Y (8-729-024-80) Q111, 211, 311, 411 2SA1908-P (8-872-024-76) 2SA1908-Y (8-872-024-77)
· A : B+ Line. · B : B Line. · Power voltage is dc 14.4V and fed with regulated dc power supply from +12V and REM terminals. · Voltage is dc with respect to ground under no-signal condition. · Voltages are taken with a VOM (Input impedance 10 M). Voltage variations may be noted due to normal production tolerances. · Waveforms are taken with a oscilloscope. Voltage variations may be noted due to normal production tolerances. · Circled numbers refer to waveforms. · Signal path. F : AUDIO for printed wiring boards: · X : parts extracted from the component side. · : Pattern from the side which enables seeing.
DISCRIMINATION:
A1908: 2SA1908 C5100: 2SC5100 P: RANK P Y: RANK Y
BCE These are omitted
8
XM-604M
3-1. BLOCK DIAGRAM
(FRONT)
PRE AMP IC801 (1/2) CN902 (1/2) L -1 3 2 HPF IC803 (1/2) 2 3 1 S801-1 VR801 LEVEL (FRONT) GAIN CONTROL AMP IC805 (2/2) VR801-2 6 HPF 6 5 7 7 MUTE CONTROL Q809 S801-2 DIFFERENTIAL AMP Q202 DRIVE AMP Q205 MUTE CONTROL Q810 DIFFERENTIAL AMP Q102 MUTE SWITCH Q201 DRIVE AMP Q105 BIAS Q106,107 DRIVE AMP Q109 POWER AMP Q111 OVERLOAD DET Q212 DIFFERENTIAL AMP Q203 DRIVE AMP Q204 BIAS Q206,207 DRIVE AMP Q209 POWER AMP Q211 DRIVE AMP Q208 POWER AMP Q210 R VR801-1 2 HPF FRONT 1 GAIN CONTROL AMP IC805 (1/2) 1 MUTE SWITCH Q101 OVERLOAD DET Q112 DIFFERENTIAL AMP Q103 DRIVE AMP Q104 DRIVE AMP Q108 POWER AMP Q110 CN903 FRONT SPEAKER OUT
L
PRE AMP IC801 (2/2) -2 R D906 INPUT CN901 HIGH LEVEL INPUT/ SENSING POWER ON FR D907 RL RR PRE AMP IC802 (1/2) CN902 (2/2) L (L+R) -3 3 2 LPF 2 3 LPF IC804 (1/2) FL 6 5 7 HPF IC803 (2/2)
S801 HPF (80Hz) (FRONT)
ON OFF
(REAR)
GAIN CONTROL AMP IC806 (1/2) VR802-1 1 2 1 MUTE CONTROL Q811 S802-1 S802 LPF (80Hz) (REAR) OFF ON 7 LPF 3 6 5 VR802 LEVEL (REAR) LPF IC804 (2/2) VR802-2 7 6 7 MUTE CONTROL Q812 DIFFERENTIAL AMP Q402 DRIVE AMP Q405 GAIN CONTROL AMP IC806 (2/2) DIFFERENTIAL AMP Q302 MUTE SWITCH Q401 DRIVE AMP Q305 MUTE SWITCH Q301 OVERLOAD DET Q312 DIFFERENTIAL AMP Q303 DRIVE AMP Q304 BIAS Q306,307 DRIVE AMP Q309 POWER AMP Q311 OVERLOAD DET Q412 DRIVE AMP Q408 BIAS Q406,407 DRIVE AMP Q409 POWER AMP Q411 POWER AMP Q410 R DRIVE AMP Q308 POWER AMP Q310 CN904(1/2) REAR SPEAKER OUT
1
L
REAR
PRE AMP IC802 (2/2) R (L+R) -4 6 5
(L+R)
DIFFERENTIAL AMP Q403
DRIVE AMP Q404
S802-2
MUTE CONTROL Q802 PROTECTOR DETECT Q901,902 F901 25A DC-DC CONVERTER IC903 B+ SWITCH Q905 OVER VOLTAGE DETECT Q907 D905 THERMAL DET Q914,915 D902 REM POWER ON/OFF Q906 G (POWER) LED DRIVER Q903 R (PROTECTOR) D918 POWER/ PROTECTOR 15 16 1 2 D901 11 10 SWITCHING DRIVER Q912,913 15V REG Q808 12 VCC 8 9 SWITCHING DRIVER Q910,911 OVERLOAD PROTECT (REAR) Q805,806
OVERLOAD PROTECT (FRONT) Q803,804
CN904(2/2) +12V
F902 25A
DC DET IC902
DC-DC CONVERTER TRANSFORMER T901
D803 RECT +30V
REF. REG TEMP.DET TH901-903 14 REF
GND
DRIVER Q908,909 D804 RECT
+15V REG Q807
+15V
· Signal path : AUDIO
30V
15V
3
XM-604M
9
9
XM-604M
3-2. PRINTED WIRING BOARD
: Uses unleaded solder.
1 A
2
3
4
5
6
7
8
9
10
11
12
13
MAIN BOARD
C823
Q311 TP17 TP18 Q310 Q411 Q410 TP20 TP22
TH903
TP19
TH902
JW135
R907
R908
R277
Q212
R278
D901
R368
R467
Q412
C817
R468
R364
R365
R465 Q407
R464
R377
Q210
C820 C818
Q207
C
R363 R369
L801
JW15
R469
R265
C822
R370 JW132 JW131 JW130 JC731 JW128 JW129 JW126 JW133 JW58 JW57 JW127 JW60 JW61 JW62 JW63 JW65 JW116 JW66 JW64 JW59 JW54 JW55 JW56
R470
JW16
JW14 JW13
Q312 JW53
R463
R477
B
TP23 TP24
K A
R264
JW19
TP25
A K
Q206
R263
TP27
D804
C
E
K
D803
R267
R270
Q307 R367
Q306
R378
Q406
R478
C821
TP902
E
C
B
E
C
B
E
C
B
E
C
B
JW18
B
TP903
JW136
JW134
C819
D807
JW17
TP21
A
R269
Q913
B
JW52
TP26
S D
· Semiconductor Location
Ref. No. D101 D102 D201 D202 D301 D302 D401 D402 D801 D802 D803 D804 D805 D806 D807 D901 D902 D904 D905 D906 D907 D918 IC801 IC802 IC803 IC804 IC805 IC806 IC902 IC903 Q101 Q102 Q103 Q104 Q105 Q106 Q107 Q108 Q109 Q110 Q111 Q112 Q201 Q202 Q203 Q204 Q205 Q206 Q207 Q208 Q209 Location E-4 E-4 E-5 E-5 F-6 F-6 F-7 F-7 G-5 G-5 B-13 C-13 D-9 D-10 B-12 B-4 F-9 G-10 G-9 I-6 I-7 I-8 H-5 H-6 G-4 G-7 G-3 G-8 F-8 E-10 F-4 F-4 F-4 E-4 E-4 E-2 E-2 E-4 E-4 E-1 F-1 D-2 F-4 F-5 F-5 E-5 E-5 C-2 C-2 E-5 E-5 Ref. No. Q210 Q211 Q212 Q301 Q302 Q303 Q304 Q305 Q306 Q307 Q308 Q309 Q310 Q311 Q312 Q401 Q402 Q403 Q404 Q405 Q406 Q407 Q408 Q409 Q410 Q411 Q412 Q802 Q803 Q804 Q805 Q806 Q807 Q808 Q809 Q810 Q811 Q812 Q901 Q902 Q903 Q905 Q906 Q907 Q908 Q909 Q910 Q911 Q912 Q913 Q914 Q915 Location C-1 D-1 B-2 F-6 F-6 F-6 E-6 E-6 B-6 B-7 E-6 E-6 A-7 A-5 C-7 G-6 F-7 F-7 E-7 E-7 B-8 B-9 E-7 E-7 A-9 A-8 B-9 G-5 H-3 H-3 F-8 F-9 D-10 D-10 F-5 F-5 F-6 F-6 E-9 E-10 I-8 G-10 G-10 H-10 E-12 E-11 E-13 F-13 E-13 D-13 G-10 G-10
R268
JW137
JW22
JW50
JW49
JW138
R166
C826
JW146 R170
JW120
JW141
R167
Q112
JW139
Q908 JC701
R922
R924
Q109
Q209
R466
R925
R366
JW48
JW115
JW68
C827
B
R178 R177 R160
C152
Q105
Q205
C252
Q808
R815
R157
C901
Q902
Q309
Q409
Q408
JW46
Q110
R156 R158
D101 R159
JC703
JW43
Q305
Q405 Q304 R359 R460
D102
R155
D202
E
JW113
R256
D201
JW112 R360 R357
JW145
JW144
Q106
JW143
JW142
Q404 JW69 R459 R457 R458
R255
TP29 Q901 C902 IC903 JW23
R921
JW10 C915
R929
D G
R356 D301
D302
R163
R355
R176 R175 Q102 Q103 JW111
R276 R275 Q202 Q203
R358
JW71 JW72
JW70
R932
S
R371 R471 C812 R813
JC704 C907
C904
R455
D402
R456
D401
R903
R910
C905
R911
JW24
C814
R169
Q812
R168
JW25
JC709 JW40
R909 R912
JW39
JW26
R262
C914
Q111
JW147
JC706
R251 R252
R809
C251
C810
R353 R354
C151
Q101
Q201
JC710
C353
JC719 C308 JC718 R408 R451 C310 C451 C408 JC717 R310 R452 R409 JW79 C410 R311 R818 R462 JW78 R412 R411 R454 R453 JW76 C411 JW86 JC716 JW80
Q809 Q810 R807 D801
Q302 R362
R938 R939 JC708
C E
R162
R161
C253 R261 Q811
R253
C913
R154
Q303 R361 Q401
Q402
Q403 C453 R461
JW74 JW75
R811 Q805 Q806
TP30
TP901
R151
C908
JC707
JW148
JW42
R816 C809 R102 JC725
Q914
JW149
JC713
JW107 R351 JC720
JW109
R104 R103 R808
C815 R304 R303 R305 R307 C351
JW150
C808
JW153
C117 C116
JW108
C108 JW110
R107
C109
TP16
C316
R936
JW154
C210 JW158
JW161
C208 R106
C106
R271
Q804
JW162
R171
R209
R309
C409
JW157
C110
R308
C211
C311
JW164
JW163
R410
C813
JW83
Q907
JW38
R405JW100
JW36
R202
R204
R205
R203
R207
JC705
JW34
R113
R404
R812
Q803
R403
C811
TP12 JW160 VR801 -1
JW97 C217 TP11 JW96 JW95 C802
-2
JW92
R301
C417
R413
H
JW4
JW3
JW2
R312 R313
-2
TP6 JC715
TP3 TP2 JW31 JW32 TP5 TP4 JW33
R942
TP15 C155
R172 TP14
TP13
R272
R111
R211
R210 R110 R112
R212
R804 C101
C255
R802
R944
C805 R805 R946 R945
JW88 JW87
JW91 JW93 R101 R201 TP10 C216 JW94 R943 C804
R401
-1
TP9 Q903 C355
R372 TP8
TP7
R472
VR802 D918
C910
C455
TP1
C102
C401
JC727
C201 C301 C402
I
-1 -2
R801
C801
R803
C803
D906
S801
JW89 JW90
-1
R905 R904 C909 R919
C202 C302 C918 CN901
D907
-2
S802
D918 POWER/ PROTECTOR
OFF ON S801 HPF(80Hz)
VR801 LEVEL
-1 L
-3 L
-1
-7 -8 FL FR RL RR
OFF ON S802 LPF(80Hz)
VR802 LEVEL
JW1
1-871-258- 11
JW159 JC732 R213
R402 R406
R810
JW84
(L+R)
-2 R
-2
JW35
R206 JW98
JW37
R917
C111
C206
JW104 IC802 JW99 JW103 C406 C205 C207 R407 JW102 C416 C405 C407 JW101
R918
JC722
JW85
R208 JW155
D904
C212
JW156
C105
R105 R302 C107 C305 C307 JW106 IC801 R306 C306 JW105
JW81
JW82
C209
C317
R935
C412
Q906 C919 R916
F901
25A L (L+R) REAR SPEAKER OUT R
F902
25A REM +12V GND
J
CNJ101
INPUT
L
R
-4 R
CN903
FRONT SPEAKER OUT FRONT REAR
HIGH LEVEL INPUT/ SENSING POWER ON
CN904
XM-604M
10
10
JW5
JC721
C309
IC804
R941
Q915
R914
JW30
L901
C911 R934
G
C112 IC805 JC726 IC803
R109 R108
JC723
JC724
JW77 C312 IC806
C920
D905
R940
JW28 JW29
JW6
IC902
JC712
JC711
R915
JW7
JW151 JW152
R806
D802 R352
JW41
Q301
D902
R817
Q905
C912
JW8
R152
Q802
R937 C903
JW27
R928
F
R376 R375
D
B
R153
C153
R254
R476
R475 JW73
C906
JW9
G
Q911
Q910
R164
JW44
C352
TH901
C
R260
JW45
JW47
E
Q308
C354
C454
R165
Q104
Q204 R257 R258 R259 JW114
JC729
JC728
JC714
C452
R901 R902
R927 R920
R930
Q107
JW67
Q909 R923
R926
C154
Q108
Q208
C254
D
JC730
JW11
G
S
Q912
R814 C825
D806
JW119
JW118
JW117
D805
TP28
C824
JW122
JC702
S
R933
E
JW140
JW121
C917
D
JW123
R266
Q807
JW21
C
T901
C916
R931
JW125
JW124
JW51
Q211
JW20
JW12
G
XM-604M
3-3. SCHEMATIC DIAGRAM -- MAIN SECTION (1/2) --
R155
R158
R175
D101
R159 Q104 Q108 R165 R167 R163 R161 C154 R162 R164 Q106 R166 Q107 R169 R178 C155 TP15 Q110 R177 R170 Q112
Q103
C152
R112 CNJ101 R102 IC801(1/2) R108 C111
VR801 R113
JC726
Q101
C151
R153
C153
R103
C105 C107 R104 R105
C108
C109 IC803(1/2)
C112
R151
R152 R156 R154
R168 Q105 Q111 Q109 R160 R171
Q102 R806
R172
R802
R801
C801 C116 C106 R106 R107 R109
C110 R111 R110
S801 IC805(1/2)
R157
R176
D102
TP14
C802
CN903 C117 R206 C207 C205 C208 C209 Q201 IC803(2/2) R252 C251 R253 C253 R263 R261 C254 JC732 R251 Q202 R943 D906 R816 R257 TP10 R201 R944 R945 R301 R358 R375 D301 R359 Q304 Q303 C808 C311 R312 Q301 C351 C353 C352 JC729 R363 R361 C354 C312 C308 R303 C815 R804 C804 C416 R307 JC720 C307 C417 C306 R306 S802 IC806(1/2) C310 JC716 IC804(1/2) R817 R357 R376 D302 R362 R351 JC724 R352 Q302 R356 R354 Q305 Q309 R360 R371 R364 Q306 R366 Q307 R369 R378 C355 TP09 R365 R367 C309 R308 R309 R310 R311 VR802 R313 JC719 R353 Q308 Q310 R377 R370 D907 JC731 R276 D202 R256 R254 Q205 Q209 R260 R271 R262 R264 Q206 R266 Q207 R269 R278 C255 TP13 R207 R209 C210 R203 C206 R211 R210 IC805(2/2) R255 R258 R275 D201 R259 Q204 Q203 C252 R265 R267 Q208 Q210 R277 R270
Q212
CN902
R202
R208 CN901 R205 R204 IC801(2/2)
C212 C211
JC727
R212
VR801 R213
R268 Q211
R272
C102
C101
C202
R101
C201
C216
C217
TP12
R401 JC722
C401 C302 C301 C402
R946 JC721 C316
R355
C317
Q312
CNJ101
R803
C803
R305
R304
IC802(1/2)
R302
C305
JC730 R368 Q311
R372
TP08 CN904
R407 R406 C407 C406 C405 R408 IC802(2/2) R409 R410 R411
JC715
IC806(2/2)
JC717 R455
R404 R403
R405
R458
R475
D401
R459 Q404 Q408 R465 R467 Q410 R477 R470
C408
C410
IC804(2/2) C412 JC718 Q401 R452 C451
Q403
C452
JC728 R463 R461 C454
Q412
R402
R453
C453
Q407 R469 R464 Q406 R466 R478 C455
TP07
C409
VR802 C411 R412
R413 R462 R451 JC723 Q402 R818 R457 R476 D402 R456 R454 Q405
C809
R468 Q411 Q409 R460 R471
R472
TP06
(Page 12)
XM-604M
11
11
XM-604M
3-4. SCHEMATIC DIAGRAM -- MAIN SECTION (2/2) --
(Page 11)
R805
C805
TP22 Q812 Q811 Q809 Q810 R922 R923 JC725 R807 D802 R808 R809 D801 C810 R927 Q913 TP25 JC714 R924 Q909 JC701 R931 R920 R921 R925 Q802 R929 Q910 Q912 R930 R926 Q908 R928 C915 R932 R933 C916 C914 TP27 D804 TP24 C820 C913 C912 L801 C817 C818 C821 C822 D805 D806 R815 Q911 T901 TP26 TP23 R814 D803 C819
Q807 TP28
C826 C824 C825 C823
C827
Q808
TP29
CN904
F902 Q905 L901
IC902
IC B/D
D807
Q803 R935 R915 TP19 R810 Q804
F901 TP05 C918 R916
C919
TH903
TH902
TH901
JC710 JC712 TP903 TP902 C906 TP901 R902 TP30 IC903
C901
R914 TP04 R919 R942 D904 Q906
Q915 R940 R936 D905 C920 R937 R939
R904
C811 D918
R812
C813
D901
Q902 R901 Q903 R905 R811 Q805 Q806
R918
JC705 C909 R917
R941 Q907 C911
R912 D902
C904 R903 JC706 C902 C812 R813 C814
R909
TP01
R934
JC708
JC709
JC707
JC704
R910 C905
JC713
· Waveform
R911
C910
R938
Q914
R908
R907
C908 C907 Q901 JC703 JC702 C917
JC711
C903
· IC Block Diagram
IC903 TL594INSR (MAIN BOARD (2/2))
VREF
1
IC903 5
NON INV
OUT
VCC
C2
E2
16
15
14
13
12 REF 5V
11
10
3.3 Vp-p
ERROR
Q2
Q1
18 µsec 1 V/DIV, 10 µsec/DIV
ERROR 1
+IN
0.1V 3
COMPEN
OSC
2
-IN
4
TIME
5
CT
6
RT
7 8
GND C1
XM-604M
12
12
E1
9
XM-604M SECTION 4 EXPLODED VIEWS
NOTE: · The mechanical parts with no reference number in the exploded views are not supplied. · Items marked "*" are not stocked since they are seldom required for routine service. Some delay should be anticipated when ordering these items. · Color Indication of Appearance Parts Example : KNOB, BALANCE (WHITE) ... (RED) R R Parts Color Cabinet's Color · Accessories are given in the last of this parts list. The components identified by mark 0 or dotted line with mark 0 are critical for safety. Replace only with part number specified. Les composants identifiés par une marque 0 sont critiques pour la sécurité. Ne les remplacer que par une piéce portant le numéro spécifié.
4-1. HEAT SINK (MAIN) SECTION
not supplied
1
2
#2 #1
3
#1 #1 F901 F902 #2 not supplied
4
4
Ref. No. 1 2 3 4
Part No. 2-695-958-11 2-695-959-11 2-894-279-01 2-894-280-01
Description PLATE (TOP), ORNAMENTAL PLATE (SIDE), ORNAMENTAL SCREW (+P 3X8) SCREW (+BTP 3X6)
Remark
Ref. No. 0 F901 0 F902 #1 #2
Part No. 1-576-256-11 1-576-256-11 7-685-146-19 7-685-545-19
Description
Remark
FUSE (BLADE TYPE) (AUTO FUSE) (25A) FUSE (BLADE TYPE) (AUTO FUSE) (25A) SCREW +P 3X8 TYPE2 NON-SLIT SCREW +BTP 3X6 TYPE2 N-S
13
XM-604M
4-2. MAIN BOARD SECTION
not supplied
52 52
51
not supplied
54
Q111,Q110, Q211,Q210 Q311,Q310,Q411,Q410
52
52 54 54
D804,D803
52
not supplied
55
Q911,Q910,Q912,Q913
52 52
55 53
#1
Ref. No. 51 52 53 54 55 D803 D804 Q110 Q110 Q111 Q111 Q210 Q210 Q211
Part No. A-1219-711-A 3-225-184-12 2-693-613-11 3-912-431-01 2-894-279-01 8-719-079-00 8-719-079-01 8-729-024-79 8-729-024-80 8-729-024-76 8-729-024-77 8-729-024-79 8-729-024-80 8-729-024-76
Description MAIN BOARD, COMPLETE SCREW (+PS.TT.3XL) PANEL, FRONT SCREW (+P) SCREW (+P 3X8) DIODE FCH10A15 DIODE FRH10A15 TRANSISTOR 2SC5100-P TRANSISTOR 2SC5100-Y TRANSISTOR 2SA1908-P TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR 2SA1908-Y 2SC5100-P 2SC5100-Y 2SA1908-P
Remark
Ref. No. Q211 Q310 Q310 Q311 Q311 Q410 Q410 Q411 Q411 Q910 Q911 Q912 Q913 #1
Part No. 8-729-024-77 8-729-024-79 8-729-024-80 8-729-024-76 8-729-024-77 8-729-024-79 8-729-024-80 8-729-024-76 8-729-024-77 6-550-341-01 6-550-341-01 6-550-341-01 6-550-341-01 7-685-146-19
Description TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR 2SA1908-Y 2SC5100-P 2SC5100-Y 2SA1908-P 2SA1908-Y
Remark
TRANSISTOR 2SC5100-P TRANSISTOR 2SC5100-Y TRANSISTOR 2SA1908-P TRANSISTOR 2SA1908-Y FET FKV550N FET FKV550N FET FKV550N FET FKV550N SCREW +P 3X8 TYPE2 NON-SLIT
Refer to page 8 for Note for Replacement of the Transistors.
14
XM-604M SECTION 5 ELECTRICAL PARTS LIST
NOTE: · Due to standardization, replacements in the parts list may be different from the parts specified in the diagrams or the components used on the set. · RESISTORS All resistors are in ohms. METAL:Metal-film resistor. METAL OXIDE: Metal oxide-film resistor. F:nonflammable · Items marked "*" are not stocked since they are seldom required for routine service. Some delay should be anticipated when ordering these items. · SEMICONDUCTORS In each case, u : µ, for example: uA.. : µA.. uPA.. : µPA.. uPB.. : µPB.. uPC.. : µPC.. uPD.. : µPD.. · CAPACITORS uF : µF · COILS uH : µH When indicating parts by reference number, please include the board. The components identified by mark 0 or dotted line with mark 0 are critical for safety. Replace only with part number specified. Les composants identifiés par une marque 0 sont critiques pour la sécurité. Ne les remplacer que par une piéce portant le numéro spécifié.
MAIN
Ref. No.
Part No.
Description
Remark
Ref. No. C306 C307 C308 C309 C310 C311 C312 C316 C317 C351 C352 C353 C354 C355 C401 C402 C405 C406 C407 C408 C409 C410 C411 C412 C416 C417 C451 C452 C453 C454 C455 C801 C802 C803 C804 C805 C808 C809 C810 C811 C812 C813 C814 C815 C817
Part No. 1-162-927-11 1-162-927-11 1-126-960-11 1-107-823-11 1-107-826-11 1-126-933-11 1-162-927-11 1-107-826-11 1-107-826-11 1-126-947-11 1-162-923-11 1-162-919-11 1-126-960-11 1-136-161-00 1-162-927-11 1-162-927-11 1-162-923-11 1-162-927-11 1-162-927-11 1-126-960-11 1-107-823-11 1-107-826-11 1-126-933-11 1-162-927-11 1-107-826-11 1-107-826-11 1-126-947-11 1-162-923-11 1-162-919-11 1-126-960-11 1-136-161-00 1-127-715-11 1-126-934-11 1-127-715-11 1-127-715-11 1-107-826-11 1-107-826-11 1-107-826-11 1-126-965-11 1-115-416-11 1-115-416-11 1-104-655-11 1-104-655-11 1-126-933-11 1-162-974-11
Description CERAMIC CHIP CERAMIC CHIP ELECT CERAMIC CHIP CERAMIC CHIP ELECT CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP ELECT CERAMIC CHIP CERAMIC CHIP ELECT FILM CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP ELECT CERAMIC CHIP CERAMIC CHIP ELECT CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP ELECT CERAMIC CHIP CERAMIC CHIP ELECT FILM CERAMIC CHIP ELECT CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP ELECT CERAMIC CHIP CERAMIC CHIP ELECT ELECT ELECT CERAMIC CHIP 100PF 100PF 1uF 0.47uF 0.1uF 100uF 100PF 0.1uF 0.1uF 47uF 47PF 22PF 1uF 0.047uF 100PF 100PF 47PF 100PF 100PF 1uF 0.47uF 0.1uF 100uF 100PF 0.1uF 0.1uF 47uF 47PF 22PF 1uF 0.047uF 0.22uF 220uF 0.22uF 0.22uF 0.1uF 0.1uF 0.1uF 22uF 0.001uF 0.001uF 470uF 470uF 100uF 0.01uF 5% 5% 20% 10% 10% 20% 5% 10% 10% 20% 5% 5% 20% 5% 5% 5% 5% 5% 5% 20% 10% 10% 20% 5% 10% 10% 20% 5% 5% 20% 5% 10% 20% 10% 10% 10% 10% 10% 20% 5% 5% 20% 20% 20%
Remark 50V 50V 50V 16V 16V 16V 50V 16V 16V 35V 50V 50V 50V 50V 50V 50V 50V 50V 50V 50V 16V 16V 16V 50V 16V 16V 35V 50V 50V 50V 50V 16V 16V 16V 16V 16V 16V 16V 50V 25V 25V 6.3V 6.3V 16V 50V
A-1219-711-A MAIN BOARD, COMPLETE ********************* 3-225-184-12 SCREW (+PS.TT.3XL) 3-912-431-01 SCREW (+P) 7-685-146-19 SCREW +P 3X8 TYPE2 NON-SLIT < CAPACITOR > C101 C102 C105 C106 C107 C108 C109 C110 C111 C112 C116 C117 C151 C152 C153 C154 C155 C201 C202 C205 C206 C207 C208 C209 C210 C211 C212 C216 C217 C251 C252 C253 C254 C255 C301 C302 C305 1-162-927-11 1-162-927-11 1-162-923-11 1-162-927-11 1-162-927-11 1-107-826-11 1-107-826-11 1-126-933-11 1-126-963-11 1-162-927-11 1-107-826-11 1-107-826-11 1-126-947-11 1-162-923-11 1-162-919-11 1-126-960-11 1-136-161-00 1-162-927-11 1-162-927-11 1-162-923-11 1-162-927-11 1-162-927-11 1-107-826-11 1-107-826-11 1-126-933-11 1-126-963-11 1-162-927-11 1-107-826-11 1-107-826-11 1-126-947-11 1-162-923-11 1-162-919-11 1-126-960-11 1-136-161-00 1-162-927-11 CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP ELECT ELECT CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP ELECT CERAMIC CHIP CERAMIC CHIP ELECT FILM CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP ELECT ELECT CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP ELECT CERAMIC CHIP CERAMIC CHIP ELECT FILM CERAMIC CHIP 100PF 100PF 47PF 100PF 100PF 0.1uF 0.1uF 100uF 4.7uF 100PF 0.1uF 0.1uF 47uF 47PF 22PF 1uF 0.047uF 100PF 100PF 47PF 100PF 100PF 0.1uF 0.1uF 100uF 4.7uF 100PF 0.1uF 0.1uF 47uF 47PF 22PF 1uF 0.047uF 100PF 100PF 47PF 5% 5% 5% 5% 5% 10% 10% 20% 20% 5% 10% 10% 20% 5% 5% 20% 5% 5% 5% 5% 5% 5% 10% 10% 20% 20% 5% 10% 10% 20% 5% 5% 20% 5% 5% 5% 5% 50V 50V 50V 50V 50V 16V 16V 16V 50V 50V 16V 16V 35V 50V 50V 50V 50V 50V 50V 50V 50V 50V 16V 16V 16V 50V 50V 16V 16V 35V 50V 50V 50V 50V 50V 50V 50V
1-162-927-11 CERAMIC CHIP 1-162-923-11 CERAMIC CHIP
15
XM-604M
MAIN
Ref. No. C818 C819 C820 C821 C822 C823 C824 C825 C826 C827 C901 C902 C903 C904 C905 C906 C907 C908 C909 C910 C911 C912 C913 C914 C915 C916 C917 C918 C919 C920 Part No. 1-162-974-11 1-165-949-31 1-165-949-31 1-165-949-31 1-165-949-31 1-115-416-11 1-107-826-11 1-107-826-11 1-126-933-11 1-126-933-11 1-100-352-11 1-107-826-11 1-162-974-11 1-162-974-11 1-130-471-00 1-126-933-11 1-107-826-11 1-126-933-11 1-115-416-11 1-137-194-81 1-107-826-11 1-136-161-00 1-131-731-12 1-131-731-12 1-162-974-11 1-162-974-11 1-162-974-11 1-100-352-11 1-162-974-11 1-126-965-11 Description CERAMIC CHIP ELECT ELECT ELECT ELECT CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP ELECT ELECT CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP MYLAR ELECT CERAMIC CHIP ELECT CERAMIC CHIP FILM CERAMIC CHIP FILM ELECT ELECT CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP ELECT < CONNECTOR > CN901 1-820-733-11 PIN, CONNECTOR (PC BOARD) 8P (HIGH LEVEL INPUT/SENSING POWER ON) < TERMINAL BOARD > CN903 CN904 1-780-132-11 TERMINAL BOARD (FRONT SPEAKER OUT) 1-780-134-11 TERMINAL BOARD (4P+3P+2FUSE) (REAR SPEAKER OUT, GND,+12V,REM,25A,25A) < JACK > CNJ101 1-779-078-21 JACK, PIN 4P (INPUT FRONT/REAR) < DIODE > D101 D102 D201 D202 D301 D302 D401 D402 D801 D802 D803 D804 D805 8-719-988-61 8-719-988-61 8-719-988-61 8-719-988-61 8-719-988-61 8-719-988-61 8-719-988-61 8-719-988-61 8-719-978-33 8-719-914-43 DIODE DIODE DIODE DIODE DIODE DIODE DIODE DIODE DIODE DIODE 1SS355TE-17 1SS355TE-17 1SS355TE-17 1SS355TE-17 1SS355TE-17 1SS355TE-17 1SS355TE-17 1SS355TE-17 DTZ-TT11-6.8B DAN202K JC711 JC712 JC713 JC714 JC715 JC716 JC717 JC718 JC719 JC720 JC721 JC722 JC723 JC724 JC725 JC726 JC727 JC728 JC729 JC730 JC731 JC732 1-216-296-11 1-216-296-11 1-216-296-11 1-216-296-11 1-216-296-11 1-216-296-11 1-216-296-11 1-216-296-11 1-216-296-11 1-216-296-11 1-216-296-11 1-216-296-11 1-216-864-11 1-216-864-11 1-216-864-11 1-216-296-11 1-216-296-11 1-216-864-11 1-216-864-11 1-216-296-11 SHORT CHIP SHORT CHIP SHORT CHIP SHORT CHIP SHORT CHIP SHORT CHIP SHORT CHIP SHORT CHIP SHORT CHIP SHORT CHIP SHORT CHIP SHORT CHIP SHORT CHIP SHORT CHIP SHORT CHIP SHORT CHIP SHORT CHIP SHORT CHIP SHORT CHIP SHORT CHIP 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0.01uF 1500uF 1500uF 1500uF 1500uF 0.001uF 0.1uF 0.1uF 100uF 100uF 1uF 0.1uF 0.01uF 0.01uF 0.001uF 100uF 0.1uF 100uF 0.001uF 0.47uF 0.1uF 0.047uF 2200uF 2200uF 0.01uF 0.01uF 0.01uF 1uF 0.01uF 22uF 20% 20% 20% 20% 5% 10% 10% 20% 20% 20% 10% Remark 50V 35V 35V 35V 35V 25V 16V 16V 16V 16V 16V 16V 50V 50V 50V 16V 16V 16V 25V 50V 16V 50V 16V 16V 50V 50V 50V 16V 50V 50V Ref. No. D806 D807 D901 D902 D904 D905 D906 D907 D918 Part No. 8-719-083-83 8-719-914-43 8-719-914-43 8-719-914-43 8-719-083-52 8-719-914-43 8-719-914-43 8-719-914-43 8-719-025-62 Description DIODE DIODE DIODE DIODE DIODE UDZS-TE17-15B DAN202K DAN202K DAN202K UDZSTE-1716B Remark
DIODE DAN202K DIODE DAN202K DIODE DAN202K LED SML1216WTP4 (POWER/PROTECTOR) < FUSE >
0 F901 0 F902
1-576-256-11 FUSE (BLADE TYPE) (AUTO FUSE) (25A) 1-576-256-11 FUSE (BLADE TYPE) (AUTO FUSE) (25A) < IC >
5% 20% 10% 20% 5% 5% 10% 5% 20% 20%
IC801 IC802 IC803 IC804 IC805 IC806 IC902 IC903
8-759-710-97 8-759-710-97 8-759-710-97 8-759-710-97 8-759-710-97
IC IC IC IC IC
NJM4565M-D NJM4565M-D NJM4565M-D NJM4565M-D NJM4565M-D
8-759-710-97 IC NJM4565M-D 6-600-354-01 IC PC-17K1 6-703-643-01 IC TL594INSR < JUMPER RESISTOR >
20% 20%
JC701 JC702 JC703 JC704 JC705 JC706 JC707 JC708 JC709 JC710
1-216-296-11 1-216-296-11 1-216-296-11 1-216-296-11 1-216-296-11 1-216-296-11 1-216-296-11 1-216-296-11 1-216-296-11 1-216-296-11
SHORT CHIP SHORT CHIP SHORT CHIP SHORT CHIP SHORT CHIP SHORT CHIP SHORT CHIP SHORT CHIP SHORT CHIP SHORT CHIP
0 0 0 0 0 0 0 0 0 0
8-719-079-00 DIODE FCH10A15 8-719-079-01 DIODE FRH10A15 8-719-083-63 DIODE UDZSTE-1713B
1-216-296-11 SHORT CHIP 1-216-864-11 SHORT CHIP
16
XM-604M
MAIN
Ref. No. Part No. Description < COIL > L801 L901 1-410-396-71 INDUCTOR, FERRITE BEAD 0.45uH 1-411-756-21 COIL, CHOKE 50uH < TRANSISTOR > Q101 Q102 Q103 Q104 Q105 Q106 Q107 Q108 Q109 Q110 Q110 Q111 Q111 Q112 Q201 Q202 Q203 Q204 Q205 Q206 Q207 Q208 Q209 Q210 Q210 Q211 Q211 Q212 Q301 Q302 Q303 Q304 Q305 Q306 Q307 Q308 Q309 Q310 Q310 Q311 Q311 Q312 Q401 Q402 Q403 Q404 Q405 Q406 Q407 Q408 Q409 Q410 6-550-686-01 8-729-014-85 8-729-014-87 8-729-140-82 8-729-140-84 8-729-041-66 8-729-026-49 8-729-020-80 8-729-232-32 8-729-024-79 8-729-024-80 8-729-024-76 8-729-024-77 8-729-120-28 6-550-686-01 8-729-014-85 8-729-014-87 8-729-140-82 8-729-140-84 8-729-041-66 8-729-026-49 8-729-020-80 8-729-232-32 8-729-024-79 8-729-024-80 8-729-024-76 8-729-024-77 8-729-120-28 6-550-686-01 8-729-014-85 8-729-014-87 8-729-140-82 8-729-140-84 8-729-041-66 8-729-026-49 8-729-020-80 8-729-232-32 8-729-024-79 8-729-024-80 8-729-024-76 8-729-024-77 8-729-120-28 6-550-686-01 8-729-014-85 8-729-014-87 8-729-140-82 8-729-140-84 8-729-041-66 8-729-026-49 8-729-020-80 TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR KTC2875-B-RTK 2SA1618-YGRTE85R 2SC4207-YGRTE85R 2SA988-PAFAEA 2SC1841-PAFAEA 2SC4015TV2 2SA1037AK-T146-R 2SC2235-O/Y(TPE6) 2SA965 2SC5100-P 2SC5100-Y 2SA1908-P 2SA1908-Y 2SC1623-L5L6 KTC2875-B-RTK 2SA1618-YGRTE85R 2SC4207-YGRTE85R 2SA988-PAFAEA 2SC1841-PAFAEA 2SC4015TV2 2SA1037AK-T146-R 2SC2235-O/Y(TPE6) 2SA965 2SC5100-P 2SC5100-Y 2SA1908-P 2SA1908-Y 2SC1623-L5L6 KTC2875-B-RTK 2SA1618-YGRTE85R 2SC4207-YGRTE85R 2SA988-PAFAEA 2SC1841-PAFAEA 2SC4015TV2 2SA1037AK-T146-R 2SC2235-O/Y(TPE6) 2SA965 2SC5100-P 2SC5100-Y 2SA1908-P 2SA1908-Y 2SC1623-L5L6 KTC2875-B-RTK 2SA1618-YGRTE85R 2SC4207-YGRTE85R 2SA988-PAFAEA 2SC1841-PAFAEA 2SC4015TV2 2SA1037AK-T146-R 2SC2235-O/Y(TPE6) Q803 Q804 Q805 Q806 Q807 Q808 Q809 Q810 Q811 Q812 Q901 Q902 Q903 Q905 Q906 Q907 Q908 Q909 Q910 Q911 Q912 Q913 Q914 Q915 8-729-120-28 8-729-120-28 8-729-120-28 8-729-120-28 8-729-209-15 8-729-209-60 8-729-027-23 8-729-027-23 8-729-027-23 8-729-027-23 8-729-027-43 8-729-027-38 8-729-027-43 8-729-052-82 8-729-120-28 8-729-027-43 6-550-686-01 6-550-686-01 6-550-341-01 6-550-341-01 6-550-341-01 6-550-341-01 8-729-120-28 8-729-026-49 TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR 2SC1623-L5L6 2SC1623-L5L6 2SC1623-L5L6 2SC1623-L5L6 2SD2012 2SB1375 DTA114EKA-T146 DTA114EKA-T146 DTA114EKA-T146 DTA114EKA-T146 DTC114EKA-T146 DTA144EKA-T146 DTC114EKA-T146 KTA1281Y-AT 2SC1623-L5L6 Remark Ref. No. Q410 Q411 Q411 Q412 Q802 Part No. 8-729-024-80 8-729-024-76 8-729-024-77 8-729-120-28 8-729-120-28 Description TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR 2SC5100-Y 2SA1908-P 2SA1908-Y 2SC1623-L5L6 2SC1623-L5L6 Remark
TRANSISTOR DTC114EKA-T146 TRANSISTOR KTC2875-B-RTK TRANSISTOR KTC2875-B-RTK FET FKV550N FET FKV550N FET FKV550N FET FKV550N TRANSISTOR 2SC1623-L5L6 TRANSISTOR 2SA1037AK-T146-R < RESISTOR >
R101 R102 R103 R104 R105 R106 R107 R108 R109 R110 R111 R112 R113 R151 R152 R153 R154 R155 R156 R157 R158 R159 R160 R161 R162 R163 R164
1-216-206-00 1-216-837-11 1-216-837-11 1-216-849-11 1-216-849-11 1-218-875-11 1-218-875-11 1-218-875-11 1-218-882-11 1-218-871-11 1-218-871-11 1-218-843-11 1-218-867-11 1-216-222-00 1-216-829-11 1-216-825-11 1-216-222-00 1-216-839-11 1-216-839-11 1-216-823-11 1-216-823-11 1-216-809-11 1-216-809-11 1-216-845-11 1-216-845-11
RES-CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP RES-CHIP METAL CHIP METAL CHIP RES-CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP
2.2K 22K 22K 220K 220K 15K 15K 15K 30K 10K 10K 680 6.8K 10K 4.7K 2.2K 10K 33K 33K 1.5K 1.5K 100 100 100K 100K 680 220
5% 5% 5% 5% 5% 0.5% 0.5% 0.5% 0.5% 0.5% 0.5% 0.5% 0.5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 0.5% 0.5%
1/8W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/8W 1/10W 1/10W 1/8W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W
8-729-232-32 TRANSISTOR 2SA965 8-729-024-79 TRANSISTOR 2SC5100-P
1-218-843-11 METAL CHIP 1-218-831-11 METAL CHIP
Refer to page 8 for Note for Replacement of the Transistors.
17
XM-604M
MAIN
Ref. No. R165 R166 R167 R168 R169 R170 R171 R172 R175 R176 R177 R178 R201 R202 R203 R204 R205 R206 R207 R208 R209 R210 R211 R212 R213 R251 R252 R253 R254 R255 R256 R257 R258 R259 R260 R261 R262 R263 R264 R265 R266 R267 R268 R269 R270 R271 R272 R275 R276 R277 R278 R301 R302 R303 R304 R305 R306 R307 Part No. 1-216-837-11 1-216-182-00 1-216-134-00 1-216-134-00 1-205-991-11 1-218-871-11 1-216-844-11 1-216-134-00 1-216-823-11 1-216-823-11 1-218-875-11 1-218-871-11 1-216-206-00 1-216-837-11 1-216-837-11 1-216-849-11 1-216-849-11 1-218-875-11 1-218-875-11 1-218-875-11 1-218-882-11 1-218-871-11 1-218-871-11 1-218-843-11 1-218-867-11 1-216-222-00 1-216-829-11 1-216-825-11 1-216-222-00 1-216-839-11 1-216-839-11 1-216-823-11 1-216-823-11 1-216-809-11 1-216-809-11 1-216-845-11 1-216-845-11 1-218-843-11 1-218-831-11 1-216-837-11 1-216-182-00 1-216-134-00 1-216-134-00 1-205-991-11 1-218-871-11 1-216-844-11 1-216-134-00 1-216-823-11 1-216-823-11 1-218-875-11 1-218-871-11 1-216-206-00 1-216-837-11 1-216-837-11 1-216-849-11 Description METAL CHIP 22K 5% RES-CHIP 220 5% RES-CHIP 2.2 5% RES-CHIP 2.2 5% ENCAPSULATED COMPONENT 0.1X2 METAL CHIP METAL CHIP RES-CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP RES-CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP RES-CHIP METAL CHIP METAL CHIP RES-CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP 10K 82K 2.2 1.5K 1.5K 15K 10K 2.2K 22K 22K 220K 220K 15K 15K 15K 30K 10K 10K 680 6.8K 10K 4.7K 2.2K 10K 33K 33K 1.5K 1.5K 100 100 100K 100K 680 220 22K 0.5% 5% 5% 5% 5% 0.5% 0.5% 5% 5% 5% 5% 5% 0.5% 0.5% 0.5% 0.5% 0.5% 0.5% 0.5% 0.5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 0.5% 0.5% 5% Remark 1/10W 1/8W 1/8W 1/8W 5W 1/10W 1/10W 1/8W 1/10W 1/10W 1/10W 1/10W 1/8W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/8W 1/10W 1/10W 1/8W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/8W 1/8W 1/8W 5W 1/10W 1/10W 1/8W 1/10W 1/10W 1/10W 1/10W 1/8W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W Ref. No. R308 R309 R310 R311 R312 R313 R351 R352 R353 R354 R355 R356 R357 R358 R359 R360 R361 R362 R363 R364 R365 R366 R367 R368 R369 R370 R371 R372 R375 R376 R377 R378 R401 R402 R403 R404 R405 R406 R407 R408 R409 R410 R411 R412 R413 R451 R452 R453 R454 R455 R456 R457 R458 R459 R460 R461 R462 R463 Part No. 1-218-853-11 1-218-871-11 1-218-871-11 1-218-853-11 1-218-843-11 1-218-867-11 1-216-222-00 1-216-829-11 1-216-825-11 1-216-222-00 1-216-839-11 1-216-839-11 1-216-823-11 1-216-823-11 1-216-809-11 1-216-809-11 1-216-845-11 1-216-845-11 1-218-843-11 1-218-831-11 1-216-837-11 1-216-182-00 1-216-134-00 1-216-134-00 1-205-991-11 1-218-871-11 1-216-844-11 1-216-134-00 1-216-823-11 1-216-823-11 1-218-875-11 1-218-871-11 1-216-206-00 1-216-837-11 1-216-837-11 1-216-849-11 1-216-849-11 1-218-875-11 1-218-875-11 1-218-853-11 1-218-871-11 1-218-871-11 1-218-853-11 1-218-843-11 1-218-867-11 1-216-222-00 1-216-829-11 1-216-825-11 1-216-222-00 1-216-839-11 1-216-839-11 1-216-823-11 1-216-823-11 1-216-809-11 1-216-809-11 Description METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP RES-CHIP METAL CHIP METAL CHIP RES-CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP 1.8K 10K 10K 1.8K 680 6.8K 10K 4.7K 2.2K 10K 33K 33K 1.5K 1.5K 100 100 100K 100K 680 220 0.5% 0.5% 0.5% 0.5% 0.5% 0.5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 0.5% 0.5% Remark 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/8W 1/10W 1/10W 1/8W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/8W 1/8W 1/8W 5W 1/10W 1/10W 1/8W 1/10W 1/10W 1/10W 1/10W 1/8W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/8W 1/10W 1/10W 1/8W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W
METAL CHIP 22K 5% RES-CHIP 220 5% RES-CHIP 2.2 5% RES-CHIP 2.2 5% ENCAPSULATED COMPONENT 0.1X2 METAL CHIP METAL CHIP RES-CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP RES-CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP RES-CHIP METAL CHIP METAL CHIP RES-CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP 10K 82K 2.2 1.5K 1.5K 15K 10K 2.2K 22K 22K 220K 220K 15K 15K 1.8K 10K 10K 1.8K 680 6.8K 10K 4.7K 2.2K 10K 33K 33K 1.5K 1.5K 100 100 100K 100K 680 0.5% 5% 5% 5% 5% 0.5% 0.5% 5% 5% 5% 5% 5% 0.5% 0.5% 0.5% 0.5% 0.5% 0.5% 0.5% 0.5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 0.5%
RES-CHIP 220 5% RES-CHIP 2.2 5% RES-CHIP 2.2 5% ENCAPSULATED COMPONENT 0.1X2 METAL CHIP 10K 0.5% METAL CHIP RES-CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP RES-CHIP METAL CHIP METAL CHIP METAL CHIP 82K 2.2 1.5K 1.5K 15K 10K 2.2K 22K 22K 220K 220K 15K 15K 5% 5% 5% 5% 0.5% 0.5% 5% 5% 5% 5% 5% 0.5% 0.5%
1-216-849-11 METAL CHIP 1-218-875-11 METAL CHIP 1-218-875-11 METAL CHIP
1-216-845-11 METAL CHIP 1-216-845-11 METAL CHIP 1-218-843-11 METAL CHIP
18
XM-604M
MAIN
Ref. No. R464 R465 R466 R467 R468 R469 R470 R471 R472 R475 R476 R477 R478 R801 R802 R803 R804 R805 R806 R807 R808 R809 R810 R811 R812 R813 R814 R815 R816 R817 R818 R901 R902 R903 R904 R905 R907 R908 R909 R910 R911 R912 R914 R915 R916 R917 R918 R919 R920 R921 R922 R923 R924 R925 R926 R927 R928 R929 Part No. 1-218-831-11 1-216-837-11 1-216-182-00 1-216-134-00 1-216-134-00 1-205-991-11 1-218-871-11 1-216-844-11 1-216-134-00 1-216-823-11 1-216-823-11 1-218-875-11 1-218-871-11 1-216-198-11 1-216-206-00 1-216-198-11 1-216-198-11 1-216-825-11 1-220-397-11 1-216-841-11 1-216-844-11 1-216-222-00 1-218-847-11 1-218-847-11 1-216-837-11 1-216-837-11 1-216-210-00 1-216-210-00 1-220-397-11 1-220-397-11 1-220-397-11 1-216-829-11 1-216-829-11 1-216-841-11 1-218-839-11 1-218-847-11 1-218-853-11 1-218-853-11 1-218-843-11 1-218-867-11 1-218-880-11 1-216-845-11 1-216-206-00 1-216-814-11 1-218-847-11 1-218-871-11 1-218-871-11 1-216-222-00 1-216-190-00 1-216-190-00 1-218-847-11 1-218-847-11 1-218-847-11 1-218-847-11 1-216-158-00 Description METAL CHIP METAL CHIP RES-CHIP RES-CHIP RES-CHIP 220 22K 220 2.2 2.2 0.5% 5% 5% 5% 5% Remark 1/10W 1/10W 1/8W 1/8W 1/8W 5W 1/10W 1/10W 1/8W 1/10W 1/10W 1/10W 1/10W 1/8W 1/8W 1/8W 1/8W 1/10W 1/10W 1/10W 1/10W 1/8W 1/10W 1/10W 1/10W 1/10W 1/8W 1/8W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/8W 1/10W 1/10W 1/10W 1/10W 1/8W 1/8W 1/8W 1/10W 1/10W 1/10W 1/10W 1/8W 1/8W 1/10W 1/10W Ref. No. R930 R931 R932 R933 R934 R935 R936 R937 R938 R939 R940 R941 R942 R943 R944 R945 R946 Part No. 1-216-789-11 1-216-789-11 1-216-150-11 1-216-150-11 1-216-825-11 1-218-871-11 1-218-871-11 1-218-847-11 1-218-871-11 1-216-839-11 1-216-206-00 1-216-829-11 1-218-871-11 1-218-871-11 1-218-871-11 Description METAL CHIP METAL CHIP RES-CHIP RES-CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP RES-CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP 2.2 2.2 10 10 2.2K 10K 10K 1K 10K 33K 2.2K 4.7K 10K 10K 10K 10K 10K 5% 5% 5% 5% 5% 0.5% 0.5% 0.5% 0.5% 5% 5% 5% 0.5% 0.5% 0.5% 0.5% 0.5% Remark 1/10W 1/10W 1/8W 1/8W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/8W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W
ENCAPSULATED COMPONENT 0.1X2 METAL CHIP 10K 0.5% METAL CHIP 82K 5% RES-CHIP 2.2 5% METAL CHIP 1.5K 5% METAL CHIP METAL CHIP METAL CHIP RES-CHIP RES-CHIP RES-CHIP RES-CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP RES-CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP RES-CHIP RES-CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP RES-CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP RES-CHIP RES-CHIP RES-CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP RES-CHIP 1.5K 15K 10K 1K 2.2K 1K 1K 2.2K 4.7M 47K 82K 10K 1K 1K 22K 22K 3.3K 3.3K 4.7M 4.7M 4.7M 4.7K 4.7K 47K 470 1K 1.8K 1.8K 680 6.8K 24K 100K 2.2K 270 1K 10K 10K 10K 470 470 1K 1K 1K 1K 22 22 2.2 2.2 5% 0.5% 0.5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 0.5% 0.5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 0.5% 0.5% 0.5% 0.5% 0.5% 0.5% 0.5% 5% 5% 5% 0.5% 0.5% 0.5% 5% 5% 5% 0.5% 0.5% 0.5% 0.5% 5% 5% 5% 5%
1-218-871-11 METAL CHIP 1-218-871-11 METAL CHIP < SWITCH >
S801 S802
1-554-222-11 SWITCH, SLIDE (HPF(80Hz) (FRONT)) 1-554-222-11 SWITCH, SLIDE (LPF(80Hz) (REAR)) < TRANSFORMER >
T901
1-443-277-21 TRANSFORMER, DC-DC CONVERTER < THERMISTOR >
TH901 TH902 TH903
1-801-597-11 THERMISTOR 1-801-597-11 THERMISTOR 1-801-597-11 THERMISTOR < VARIABLE RESISTOR >
VR801 1-227-768-11 RES, VAR, CARBON 10KX2 (LEVEL (FRONT)) VR802 1-227-768-11 RES, VAR, CARBON 10KX2 (LEVEL (REAR)) ************************************************************* ACCESSORY *********** 2-894-199-11 MANUAL, INSTRUCTION (ENGLISH,FRENCH) 2-894-199-21 MANUAL, INSTRUCTION (SPANISH,GERMAN) 2-894-199-31 MANUAL, INSTRUCTION (DUTCH,ITALIAN) ************************************************************* PARTS FOR INSTALLATION AND CONNECTIONS *************************************** 101 102 103 X-2176-063-1 SCREW SUB ASSY (MOUNTING SCREW) 1-823-952-11 CORD (WITH CONNECTOR) (HIGH LEVEL INPUT) (0.2m) 2-695-957-01 COVER (POWER)
101
5 × 15 mm (× 4)
102
103
0.2 m
1-216-158-00 RES-CHIP 1-216-789-11 METAL CHIP 1-216-789-11 METAL CHIP
19
XM-604M
REVISION HISTORY
Clicking the version allows you to jump to the revised page. Also, clicking the version at the upper on the revised page allows you to jump to the next revised page. Ver. 1.0 Date 2006. 10 Description of Revision New
20