Text preview for : PHILIPS_Q528.2E_LA.pdf part of PHILIPS PHILIPS chassis Q528.2E LA
Back to : PHILIPS_Q528.2E_LA.part01 | Home
Colour Television
Chassis
Q528.2E
LA
ME8
ME8+
H_17650_000.eps 160108
Contents
Page
Contents
8. 9. 10. 11. Alignments IC Data Sheets Spare Parts List & CTN Overview Revision List
Page
115 123 135 135
1. Technical Specifications, Connections, and Chassis Overview 2 2. Safety Instructions, Warnings, and Notes 6 3. Directions for Use 7 4. Mechanical Instructions 8 5. Service Modes, Error Codes, and Fault Finding 16 6. Block Diagrams, Test Point Overview, and Waveforms Wiring Diagram 32" (ME8) 37 Wiring Diagram 42" (ME8) 38 Block Diagram Video 39 Block Diagram Audio 40 Block Diagram Control & Clock Signals 41 SSB: Test Points (Top Side) 42 SSB: Test Points (Bottom Side) 43 I2C IC Overview 44 Supply Lines Overview 45 7. Circuit Diagrams and PWB Layouts Drawing LCD Supply (37 & 42"): Part 1(A1) 46 LCD Supply (37 & 42"): Part 2 (A2) 47 Small Signal Board (B02-B10) 50 SSB: SRP List Explanation 95 SSB: SRP List Part 1 96 SSB: SRP List Part 2 97 Keyboard Control Panel (E) 108 IR & LED Panel (J) 109 Light Guide Panel (32") (LG) 111 Light Guide Panel (47 & 52") (LG) 113
PWB 48-49 48-49 98-107
108 110 112 114
© Copyright 2008 Koninklijke Philips Electronics N.V. All rights reserved. No part of this publication may be reproduced, stored in a retrieval system or transmitted, in any form or by any means, electronic, mechanical, photocopying, or otherwise without the prior permission of Philips.
Published by JY 0866 BU TV Consumer Care
Printed in the Netherlands
Subject to modification
EN 3122 785 17651
EN 2
1.
Q528.2E LA
Technical Specifications, Connections, and Chassis Overview
1. Technical Specifications, Connections, and Chassis Overview
Index of this chapter: 1.1 Technical Specifications 1.2 Connections 1.3 Chassis Overview Notes: · Figures can deviate due to the different set executions. · Specifications are indicative (subject to change). 1.1.4 1.1.3 Multimedia Supported file formats : JPEG : MP3 : Slideshow (.alb) : USB2.0
USB input Miscellaneous Power supply: - Mains voltage (VAC) - Mains frequency (Hz)
1.1
1.1.1
Technical Specifications
Vision Display type Screen size Resolution (H × V pixels) Light output (cd/m2) Contrast ratio Viewing angle (H × V degrees) Tuning system Colour systems : : : : : : : : : : : : : : : : : : : : : : : : : : : LCD 32" (82 cm), 16:9 42" (107 cm), 16:9 1366 × 768p (32") 1920 × 1080p (42") 500 (32") 550 (42") 40000:1 (32") 30000:1 (42") 176 × 176 PLL PAL B/G, D/K, I SECAM B/G, D/K, L/L' DVB-T DVB-C (in some sets) DVB-T MPEG4 (42PFL5603H/10) NTSC PAL SECAM UHF, VHF, S, Hyper 480i @ 60 Hz 480p @ 60 Hz 576i @ 50 Hz 576p @ 50 Hz 720p @ 50/60 Hz 1080i @ 50/60 Hz 1080p @ 24/25/30/ 50/60 Hz : 220 - 240 ±10% : 50 / 60
Ambient conditions: - Temperature range (°C)
: +5 to +35
Power consumption (values are indicative) - Normal operation (W) : 140 (32") : 200 (42") : 210 (42PFL7603D/12) - Standby (W) : < 0.15 Dimensions (W × H × D in cm) : 81.9 × 51.8 × 9.5 (32") : 104.6 × 64.4 × 8.8 (42") : 104.6 × 64.4 × 11.1 (42PFL7603D/12) : 19 (32") : 21 (42") : 22.5 (42PFL7603D/12)
Weight (kg)
Video playback
Tuner bands Supported video formats
Supported computer formats: - 60, 70, 75, 85 Hz - 60, 72, 75, 85 Hz - 60, 70, 75, 85 Hz 1.1.2 Sound Maximum power (WRMS)
: 1024 × 768 : 800 × 600 : 640 × 480
: 2 × 15
Technical Specifications, Connections, and Chassis Overview 1.2 Connections
Q528.2E LA
1.
EN 3
SERV. U
SPDIF OUT
EXT 3
Y
(RGB/CVBS)
EXT 2
(RGB/CVBS)
EXT 1
L AUDIO OUT R Pr L AUDIO IN R Pb
75X
TV ANTENNA
OPTIONAL
AUDIO IN: HDMI 3 HDMI 2 HDMI 1
LEFT / RIGHT HDMI 1 / DVI HDMI 2 / DVI HDMI 3 / DVI
H_17650_083.eps 160108
Figure 1-1 Connection overview Note: The following connector colour abbreviations are used (acc. to DIN/IEC 757): Bk= Black, Bu= Blue, Gn= Green, Gy= Grey, Rd= Red, Wh= White, Ye= Yellow. 1.2.1 Side Connections Headphone (Output) Bk - Headphone 32 - 600 ohm / 10 mW Cinch: Video CVBS - In, Audio - In Rd - Audio R 0.5 VRMS / 10 kohm Wh - Audio L 0.5 VRMS / 10 kohm Ye - Video CVBS 1 VPP / 75 ohm S-Video (Hosiden): Video Y/C - In 1 - Ground Y Gnd 2 - Ground C Gnd 3 - Video Y 1 VPP / 75 ohm 4 - Video C 0.3 VPP / 75 ohm USB2.0 HDMI: Digital Video, Digital Audio - In
19 18 1 2
E_06532_017.eps 250505
Figure 1-3 HDMI (type A) connector ot 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 - D2+ - Shield - D2- D1+ - Shield - D1- D0+ - Shield - D0- CLK+ - Shield - CLK- n.c. - n.c. - DDC_SCL - DDC_SDA - Ground - +5V - HPD - Ground Data channel Gnd Data channel Data channel Gnd Data channel Data channel Gnd Data channel Data channel Gnd Data channel j H j j H j j H j j H j j jk H j j H
jq jq jq
H H j j
1
2
3
4
DDC clock DDC data Gnd Hot Plug Detect Gnd
E_06532_022.eps 300904
Figure 1-2 USB (type A) 1 2 3 4 - +5V - Data (-) - Data (+) - Ground k jk jk H Common Interface 68p - See diagram B09A jk
Gnd
EN 4
1.2.2
1.
Q528.2E LA
Technical Specifications, Connections, and Chassis Overview
3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 - D2- D1+ - Shield - D1- D0+ - Shield - D0- CLK+ - Shield - CLK- n.c. - n.c. - DDC_SCL - DDC_SDA - Ground - +5V - HPD - Ground Data channel Data channel Gnd Data channel Data channel Gnd Data channel Data channel Gnd Data channel j j H j j H j j H j j jk H j j H
Rear Connections Service Connector (UART) 1 - Ground Gnd 2 - UART_TX Transmit 3 - UART_RX Receive Cinch: S/PDIF - Out Bk - Coaxial Cinch: Audio - Out Rd - Audio - R Wh - Audio - L
H k j
0.4 - 0.6VPP / 75 ohm
kq
0.5 VRMS / 10 kohm 0.5 VRMS / 10 kohm
kq kq
DDC clock DDC data Gnd Hot Plug Detect Gnd
EXT3: Cinch: Video YPbPr - In Gn - Video Y 1 VPP / 75 ohm Bu - Video Pb 0.7 VPP / 75 ohm Rd - Video Pr 0.7 VPP / 75 ohm EXT3: Cinch: Audio - In Rd - Audio - R 0.5 VRMS / 10 kohm Wh - Audio - L 0.5 VRMS / 10 kohm
jq jq jq
jq jq
Mini Jack: HDMI/DVI Audio - In Rd - Audio - R 0.5 VRMS / 10 kohm Wh - Audio - L 0.5 VRMS / 10 kohm
jq jq
EXT2, EXT1: Video RGB - In, CVBS - In/Out, Audio - In/Out
20
2
21
E_06532_001.eps 050404
1
Figure 1-4 SCART connector 1 2 3 4 5 6 7 8 - Audio R - Audio R - Audio L - Ground Audio - Ground Blue - Audio L - Video Blue - Function Select 0.5 VRMS / 1 kohm 0.5 VRMS / 10 kohm 0.5 VRMS / 1 kohm Gnd Gnd 0.5 VRMS / 10 kohm 0.7 VPP / 75 ohm 0 - 2 V: INT 4.5 - 7 V: EXT 16:9 9.5 - 12 V: EXT 4:3 Gnd 0 - 5 V / 4.7 kohm 0.7 VPP / 75 ohm Gnd Gnd 0.7 VPP / 75 ohm 0 - 0.4 V: INT 1 - 3 V: EXT / 75 ohm Gnd Gnd 1 VPP / 75 ohm 1 VPP / 75 ohm Gnd k j k H H j jk j H jk j H H j j H H k j H
9 10 11 12 13 14 15 16 17 18 19 20 21
- Ground Green - Easylink P50 - Video Green - n.c. - Ground Red - Ground P50 - Video Red - Status/FBL - Ground Video - Ground FBL - Video CVBS - Video CVBS - Shield
Aerial - In - - IEC-type (EU)
Coax, 75 ohm
D
HDMI 1, 2 (& 3: optional): Digital Video, Digital Audio - In
19 18 1 2
E_06532_017.eps 250505
Figure 1-5 HDMI (type A) connector 1 2 - D2+ - Shield Data channel Gnd j H
Technical Specifications, Connections, and Chassis Overview 1.3 Chassis Overview
Q528.2E LA
1.
EN 5
A E
MAIN SUPPLY PANEL KEYBOARD CONTROL PANEL SMALL SIGNAL BOARD
B
H_17650_083.eps 160108
J
IR & LED PANEL
LIGHT GUIDE PANEL
LG
H_17650_086.eps 230508
Figure 1-6 PWB/CBA locations sets with AmbiLight
A E
MAIN SUPPLY PANEL KEYBOARD CONTROL PANEL SMALL SIGNAL BOARD
B
H_17650_083.eps 160108
J
IR & LED PANEL
LIGHT GUIDE PANEL
LG
H_17650_084.eps 230508
Figure 1-7 PWB/CBA locations sets without AmbiLight
EN 6
2.
Q528.2E LA
Safety Instructions, Warnings, and Notes
2. Safety Instructions, Warnings, and Notes
Index of this chapter: 2.1 Safety Instructions 2.2 Warnings 2.3 Notes · Where necessary, measure the waveforms and voltages with (D) and without (E) aerial signal. Measure the voltages in the power supply section both in normal operation (G) and in stand-by (F). These values are indicated by means of the appropriate symbols.
2.1
Safety Instructions
Safety regulations require the following during a repair: · Connect the set to the Mains/AC Power via an isolation transformer (> 800 VA). · Replace safety components, indicated by the symbol h, only by components identical to the original ones. Any other component substitution (other than original type) may increase risk of fire or electrical shock hazard. Safety regulations require that after a repair, the set must be returned in its original condition. Pay in particular attention to the following points: · Route the wire trees correctly and fix them with the mounted cable clamps. · Check the insulation of the Mains/AC Power lead for external damage. · Check the strain relief of the Mains/AC Power cord for proper function. · Check the electrical DC resistance between the Mains/AC Power plug and the secondary side (only for sets that have a Mains/AC Power isolated power supply): 1. Unplug the Mains/AC Power cord and connect a wire between the two pins of the Mains/AC Power plug. 2. Set the Mains/AC Power switch to the "on" position (keep the Mains/AC Power cord unplugged!). 3. Measure the resistance value between the pins of the Mains/AC Power plug and the metal shielding of the tuner or the aerial connection on the set. The reading should be between 4.5 M and 12 M. 4. Switch "off" the set, and remove the wire between the two pins of the Mains/AC Power plug. · Check the cabinet for defects, to prevent touching of any inner parts by the customer.
2.3.2
Schematic Notes · All resistor values are in ohms, and the value multiplier is often used to indicate the decimal point location (e.g. 2K2 indicates 2.2 k). Resistor values with no multiplier may be indicated with either an "E" or an "R" (e.g. 220E or 220R indicates 220 ). All capacitor values are given in micro-farads ( = × 10-6), nano-farads (n = × 10-9), or pico-farads (p = × 10-12). Capacitor values may also use the value multiplier as the decimal point indication (e.g. 2p2 indicates 2.2 pF). An "asterisk" (*) indicates component usage varies. Refer to the diversity tables for the correct values. The correct component values are listed in the Spare Parts List. Therefore, always check this list when there is any doubt.
· · · · ·
2.3.3
BGA (Ball Grid Array) ICs Introduction For more information on how to handle BGA devices, visit this URL: www.atyourservice.ce.philips.com (needs subscription, not available for all regions). After login, select "Magazine", then go to "Repair downloads". Here you will find Information on how to deal with BGA-ICs. BGA Temperature Profiles For BGA-ICs, you must use the correct temperature-profile, which is coupled to the 12NC. For an overview of these profiles, visit the website www.atyourservice.ce.philips.com (needs subscription, but is not available for all regions) You will find this and more technical information within the "Magazine", chapter "Repair downloads". For additional questions please contact your local repair help desk.
2.2
Warnings
· All ICs and many other semiconductors are susceptible to electrostatic discharges (ESD w). Careless handling during repair can reduce life drastically. Make sure that, during repair, you are connected with the same potential as the mass of the set by a wristband with resistance. Keep components and tools also at this same potential. Be careful during measurements in the high voltage section. Never replace modules or other components while the unit is switched "on". When you align the set, use plastic rather than metal tools. This will prevent any short circuits and the danger of a circuit becoming unstable. 2.3.4
Lead-free Soldering Due to lead-free technology some rules have to be respected by the workshop during a repair: · Use only lead-free soldering tin Philips SAC305 with order code 0622 149 00106. If lead-free solder paste is required, please contact the manufacturer of your soldering equipment. In general, use of solder paste within workshops should be avoided because paste is not easy to store and to handle. · Use only adequate solder tools applicable for lead-free soldering tin. The solder tool must be able: To reach a solder-tip temperature of at least 400°C. To stabilize the adjusted temperature at the solder-tip. To exchange solder-tips for different applications. · Adjust your solder tool so that a temperature of around 360°C - 380°C is reached and stabilized at the solder joint. Heating time of the solder-joint should not exceed ~ 4 sec. Avoid temperatures above 400°C, otherwise wear-out of tips will increase drastically and flux-fluid will be destroyed. To avoid wear-out of tips, switch "off" unused equipment or reduce heat. · Mix of lead-free soldering tin/parts with leaded soldering tin/parts is possible but PHILIPS recommends strongly to avoid mixed regimes. If this cannot be avoided, carefully clear the solder-joint from old tin and re-solder with new tin.
· · ·
2.3
2.3.1
Notes
General · Measure the voltages and waveforms with regard to the chassis (= tuner) ground (H), or hot ground (I), depending on the tested area of circuitry. The voltages and waveforms shown in the diagrams are indicative. Measure them in the Service Default Mode (see chapter 5) with a colour bar signal and stereo sound (L: 3 kHz, R: 1 kHz unless stated otherwise) and picture carrier at 475.25 MHz for PAL, or 61.25 MHz for NTSC (channel 3).
Directions for Use
2.3.5 Alternative BOM identification
MODEL
Q528.2E LA
3.
EN 7
: 32PF9968/10
Note: on European Service website, "Alternative BOM" is referred to as "Design variant".
PROD.NO: AG 1A0617 000001
MADE IN BELGIUM 220-240V ~ 50/60Hz 128W VHF+S+H+UHF
The third digit in the serial number (example: AG2B0335000001) indicates the number of the alternative B.O.M. (Bill Of Materials) that has been used for producing the specific TV set. In general, it is possible that the same TV model on the market is produced with e.g. two different types of displays, coming from two different suppliers. This will then result in sets which have the same CTN (Commercial Type Number; e.g. 28PW9515/12) but which have a different B.O.M. number. By looking at the third digit of the serial number, one can identify which B.O.M. is used for the TV set he is working with. If the third digit of the serial number contains the number "1" (example: AG1B033500001), then the TV set has been manufactured according to B.O.M. number 1. If the third digit is a "2" (example: AG2B0335000001), then the set has been produced according to B.O.M. no. 2. This is important for ordering the correct spare parts! For the third digit, the numbers 1...9 and the characters A...Z can be used, so in total: 9 plus 26= 35 different B.O.M.s can be indicated by the third digit of the serial number. Identification: The bottom line of a type plate gives a 14-digit serial number. Digits 1 and 2 refer to the production centre (e.g. AG is Bruges), digit 3 refers to the B.O.M. code, digit 4 refers to the Service version change code, digits 5 and 6 refer to the production year, and digits 7 and 8 refer to production week (in example below it is 2006 week 17). The 6 last digits contain the serial number.
S
Figure 2-1 Serial number (example) 2.3.6
BJ3.0E LA
E_06532_024.eps 260308
Board Level Repair (BLR) or Component Level Repair (CLR) If a board is defective, consult your repair procedure to decide if the board has to be exchanged or if it should be repaired on component level. If your repair procedure says the board should be exchanged completely, do not solder on the defective board. Otherwise, it cannot be returned to the O.E.M. supplier for back charging!
2.3.7
Practical Service Precautions · It makes sense to avoid exposure to electrical shock. While some sources are expected to have a possible dangerous impact, others of quite high potential are of limited current and are sometimes held in less regard. Always respect voltages. While some may not be dangerous in themselves, they can cause unexpected reactions that are best avoided. Before reaching into a powered TV set, it is best to test the high voltage insulation. It is easy to do, and is a good service precaution.
·
3. Directions for Use
You can download this information from the following websites: http://www.philips.com/support http://www.p4c.philips.com
EN 8
4.
Q528.2E LA
Mechanical Instructions
4. Mechanical Instructions
Index of this chapter: 4.1 Cable Dressing 4.2 Service Positions 4.3 Assy/Panel Removal ME8(+) Styling 4.4 Set Re-assembly Notes: · Figures below can deviate slightly from the actual situation, due to the different set executions.
4.1
Cable Dressing
I_17651_001.eps 110608
Figure 4-1 Cable dressing 32" sets without AmbiLight
Mechanical Instructions
Q528.2E LA
4.
EN 9
H_17650_085.eps 170108
Figure 4-2 Cable dressing 42" sets with AmbiLight
H_17650_087.eps 160108
Figure 4-3 Cable dressing 42" sets without AmbiLight
EN 10 4.2
4.
Q528.2E LA
Mechanical Instructions
3. Remove the screws [2], gently lift the back cover from the set and unplug the Ambilight power connector [4]. 4. Lift the back cover from the TV. Make sure that wires and flat coils are not damaged while lifting the rear cover from the set.
Service Positions
For easy servicing of this set, there are a few possibilities created: · The buffers from the packaging (see figure "Rear cover"). · Foam bars (created for Service). · Aluminium service stands (created for Service).
4.2.1
Foam Bars
1
1
Required for sets 42"
E_06532_018.eps 171106
Figure 4-4 Foam bars The foam bars (order code 3122 785 90580 for two pieces) can be used for all types and sizes of Flat TVs. See figure "Foam bars" for details. Sets with a display of 42" and larger, require four foam bars [1]. Ensure that the foam bars are always supporting the cabinet and never only the display. Caution: Failure to follow these guidelines can seriously damage the display! By laying the TV face down on the (ESD protective) foam bars, a stable situation is created to perform measurements and alignments. By placing a mirror under the TV, you can monitor the screen.
4.3
4.3.1
Assy/Panel Removal ME8(+) Styling
Rear Cover Warning: Disconnect the mains power cord before you remove the rear cover. Note: it is not necessary to remove the stand while removing the rear cover. Warning: Most sets have an additional hatch located in the rear cover. These are meant for disconnecting the flat cables to the AmbiLight units in the rear cover, before the rear cover is lifted from the set. The hatches are not always located at the same place for all sets, therefore the figures below are only meant as indication. It is mandatory to locate these hatches first, open them, and unplug connectors behind. Lifting the back cover without having done so, could result in damaging the connectors inside! Refer to next figures for details. 1. First remove the screws [1] from the back cover hatch and remove the hatch. 2. Then unplug connector [3].
Mechanical Instructions
Q528.2E LA
4.
EN 11
2 2
2
2
2
2 2
2
2 2 2
1 1 2 2 2
2
2
2
2
2
2
2
2
H_17650_100.eps 180108
Figure 4-5 Back Cover Removal [1/3]
3 4
H_17650_099.eps 180108
H_17650_101.eps 180108
Figure 4-7 Back Cover Removal [3/3] Figure 4-6 Back Cover Removal [2/3]
EN 12
4.3.2
4.
Q528.2E LA
Mechanical Instructions
Ambilight Refer to next figure for details. 1. Unplug the connectors [1]. 2. Remove the screws [2]. 3. Pull the unit sidewards from the back cover. When defective, replace the whole unit.
1
2
H_17650_095.eps 180108
Figure 4-10 Tweeter
2
4.3.5
IR & LED Board Refer to next figure for details. 1. Unplug connectors [1]. 2. Use a flat screw driver to release the clip by pushing it in the indicated direction [2]. 3. Lift the board and take it out of the set. When defective, replace the whole unit.
1
H_17650_097.eps 180108
1
Figure 4-8 Ambilight Unit 4.3.3 Woofers Refer to next figure for details. 1. Remove the screws [1] and lift the whole unit from the back cover. Take the speakers out together with their casing. When defective, replace the whole unit.
2
H_17650_098.eps 180108
Figure 4-11 IR & LED Board
1
H_17650_096.eps 180108
Figure 4-9 Woofer 4.3.4 Tweeters Refer to next figure for details. Warning: The speakers should never be connected or disconnected when the set is playing! This can damage the amplifiers on the SSB. 1. Remove the screws [1] lift the whole unit from the back cover. When defective, replace the whole unit.
Mechanical Instructions
4.3.6 Key Board Refer to next figure for details. 1. Unplug the key board connector from the IR & LED board. 2. Remove the screws [1]. 3. Lift the unit and take it out of the set. When defective, replace the whole unit. 4.3.7
Q528.2E LA
4.
EN 13
Display Supply Panel Refer to next figure for details. 1. Unplug connectors [1]. 2. Remove the fixation screws [2]. 3. Take the board out.
2
1 1 2
2 1
2 1 2
2
1 2
H_17650_094.eps 180108
2
H_17650_102.eps 180108
Figure 4-13 Display Supply Panel Figure 4-12 Key Board
EN 14
4.3.8
4.
Q528.2E LA
Mechanical Instructions
Small Signal Board (SSB) Refer to next figure for details. Caution: it is mandatory to remount all different screws at their original position during re-assembly. Failure to do so may result in damaging the SSB. Refer to next figures or details. 1. Unplug the LVDS connector [1]. Caution: be careful, as this is a very fragile connector! 2. Unplug the connectors [2]. 3. Remove the screws [3]. 4. The SSB can now be taken out of the set, together with the front shield and the side cover. 5. To remove the shield, remove the screws [4] and lift it of. 6. To remove the side cover remove the screws [5]. 7. Release clip [6] and slide the pull the cover sidewards from the SSB.
1 3 3 6
3
3 3 5 2 4 4 4 3
3
4
4 3
4
H_17650_103.eps 180108
Figure 4-14 Small Signal Board
Mechanical Instructions
4.3.9 LCD Panel / Lightguide Refer to next figures for details. 1. Unplug the LVDS connector [1]. Caution: be careful, as this is a very fragile connector! 2. Unplug the connectors [2]. 3. Remove the fixation screws [3] from rim. 4. Take the rim from the set. 5. Remove the fixation screws [4] and [5]. 6. Lift the subframe from the set. 7. The LCD panel can now be lifted from the front cabinet. When the Lightguide is defective the entire front cabinet has to be removed. To do so follow the previous steps to remove the LCD panel as well as removing the IR LED panel and Tweeters.
Q528.2E LA
4.
EN 15
4
4 4
5 3
5
5
5
1
2 3 5
2
5 4 4 4
5 4
5
4
2
H_17650_104.eps 180108
Figure 4-15 LCD Panel / Lightguide
4.4
Set Re-assembly
To re-assemble the whole set, execute all processes in reverse order. Notes: · While re-assembling, make sure that all cables are placed and connected in their original position. See figure "Cable dressing". · Pay special attention not to damage the EMC foams on the SSB shields. Ensure that EMC foams are mounted correctly.
EN 16
5.
Q528.2E LA
Service Modes, Error Codes, and Fault Finding
5. Service Modes, Error Codes, and Fault Finding
Index of this chapter: 5.1 Test Points 5.2 Service Modes 5.3 Stepwise Start-up 5.4 Service Tools 5.5 Error Codes 5.6 The Blinking LED Procedure 5.7 Protections 5.8 Fault Finding and Repair Tips 5.9 Software Upgrading Picture mute (blue mute or black mute). Automatic volume levelling (AVL). Skip/blank of non-favourite pre-sets.
5.1
Test Points
As most signals are digital, it will be difficult to measure waveforms with a standard oscilloscope. However, several key ICs are capable of generating test patterns, which can be controlled via ComPair. In this way it is possible to determine which part is defective. Perform measurements under the following conditions: · Service Default Mode. · Video: Colour bar signal. · Audio: 3 kHz left, 1 kHz right.
How to Activate SDM For this chassis there are two kinds of SDM: an analogue SDM and a digital SDM. Tuning will happen according table "SDM Default Settings". · Analogue SDM: use the standard RC-transmitter and key in the code "062596", directly followed by the "MENU" button. Note: It is possible that, together with the SDM, the main menu will appear. To switch it "off", push the "MENU" button again. · Digital SDM: use the standard RC-transmitter and key in the code "062593", directly followed by the "MENU" button. Note: It is possible that, together with the SDM, the main menu will appear. To switch it "off", push the "MENU" button again. · Analogue SDM can also be activated by shorting for a moment the two solder pads [1] (see figure "Service mode pads") on the SSB, with the indication "SDM". Activation can be performed in all modes, except when the set has a problem with the Stand-by Processor.
5.2
Service Modes
Service Default mode (SDM) and Service Alignment Mode (SAM) offers several features for the service technician, while the Customer Service Mode (CSM) is used for communication between the call centre and the customer. This chassis also offers the option of using ComPair, a hardware interface between a computer and the TV chassis. It offers the abilities of structured troubleshooting, error code reading, and software version read-out for all chassis. (see also paragraph "ComPair").
SDM
5.2.1
Service Default Mode (SDM) Purpose · To create a pre-defined setting, to get the same measurement results as given in this manual. · To override SW protections detected by stand-by processor and make the TV start up to the step just before protection (a sort of automatic stepwise start up). See paragraph "Stepwise Start Up". · To override SW protections detected by MIPS. See also paragraph "Error codes". · To start the blinking LED procedure (not valid for protections detected by standby software). Specifications Table 5-1 SDM default settings Default system PAL B/G
H_17650_088.eps 160108
Figure 5-1 Service mode pads After activating this mode, "SDM" will appear in the upper right corner of the screen (if you have picture). How to Navigate When you press the "MENU" button on the RC transmitter, the set will toggle between the SDM and the normal user menu (with the SDM mode still active in the background). How to Exit SDM Use one of the following methods: · Switch the set to STAND-BY via the RC-transmitter. · Via a standard customer RC-transmitter: key in "00"sequence. 5.2.2 Service Alignment Mode (SAM) Purpose · To perform (software) alignments. · To change option settings. · To easily identify the used software version. · To view operation hours. · To display (or clear) the error code buffer.
Region Europe, AP(PAL/Multi) Europe, AP DVB-T
Freq. (MHz) 475.25
DVB-T 546.00 PID Video: 0B 06 PID PCR: 0B 06 PID Audio: 0B 07
· · ·
All picture settings at 50% (brightness, colour, contrast). All sound settings at 50%, except volume at 25%. All service-unfriendly modes (if present) are disabled, like: (Sleep) timer. Child/parental lock.
Service Modes, Error Codes, and Fault Finding
How to Activate SAM Via a standard RC transmitter: key in the code "062596" directly followed by the "INFO" button. After activating SAM with this method a service warning will appear on the screen, you can continue by pressing the red button on the RC. Contents of SAM: · Hardware Info. A. SW Version. Displays the software version of the main software (example: Q582E-1.2.3.4 = AAAAB_X.Y.W.Z). · AAAA= the chassis name. · B= the region: A= AP, E= EU, L= LatAm, U = US. For AP sets it is possible that the Europe software version is used. · X.Y.W.Z= the software version, where X is the main version number (different numbers are not compatible with one another) and Y.W.Z is the sub version number (a higher number is always compatible with a lower number). B. SBY PROC Version. Displays the software version of the stand-by processor. C. Production Code. Displays the production code of the TV, this is the serial number as printed on the back of the TV set. Note that if an NVM is replaced or is initialized after corruption, this production code has to be re-written to NVM. ComPair will foresee in a possibility to do this. · Operation Hours. Displays the accumulated total of operation hours (not the stand-by hours). Every time the TV is switched "on/off", 0.5 hours is added to this number. · Errors (followed by maximal 10 errors). The most recent error is displayed at the upper left (for an error explanation see paragraph "Error Codes"). · Reset Error Buffer. When you press "cursor right" (or the "OK button) and then the "OK" button, the error buffer is reset. · Alignments. This will activate the "ALIGNMENTS" submenu. · Dealer Options. Extra features for the dealers. · Options. Extra features for Service. For more info regarding option codes, see chapter 8 "Alignments". Note that if you change the option code numbers, you have to confirm your changes with the "OK" button before you store the options. Otherwise you will loose your changes. · Initialize NVM. The moment the processor recognizes a corrupted NVM, the "initialize NVM" line will be highlighted. Now, you can do two things (dependent of the service instructions at that moment): Save the content of the NVM via ComPair for development analysis, before initializing. This will give the Service department an extra possibility for diagnosis (e.g. when Development asks for this). Initialize the NVM. Note: When you have a corrupted NVM, or you have replaced the NVM, there is a high possibility that you will not have picture anymore because your display code is not correct. So, before you can initialize your NVM via the SAM, you need to have a picture and therefore you need the correct display option. Refer to chapter 8 for details. To adapt this option, you can use ComPair (the correct HEX values for the options can be found in chapter 8 "Alignments") or a method via a standard RC (described below). Changing the display option via a standard RC: Key in the code "062598" directly followed by the "MENU" button and "XXX", where XXX is the 3 digit decimal display code (see table "Option code overview" in chapter 8 "Alignments", or sticker on the side/bottom of the cabinet). Make sure to key in all three digits, also the leading zero's. If the above action is successful, the front LED will go out as an indication that the RC sequence was correct. After the display option is changed in the NVM, the TV will go to the Stand-by mode. If the NVM was corrupted or
Q528.2E LA
5.
EN 17
empty before this action, it will be initialized first (loaded with default values). This initializing can take up to 20 seconds.
Display Option Code
39mm
PHILIPS
27mm
040
MODEL: 32PF9968/10
PROD.SERIAL NO: AG 1A0620 000001
(CTN Sticker)
E_06532_038.eps 240108
Figure 5-2 Location of Display Option Code sticker · Store. All options and alignments are stored when pressing "cursor right" (or the "OK" button) and then the "OK"-button. SW Maintenance. SW Events. Not useful for Service purposes. In case of specific software problems, the development department can ask for this info. HW Events. Not useful for Service purposes. In case of specific software problems, the development department can ask for this info. Test settings. For development purposes only. Upload to USB. To upload several settings from the TV to a USB stick, which is connected to the Side I/O. The items are "Channel list", "Personal settings", "Option codes", "Display-related alignments" and "History list". First you have to create a directory "repair" in the root of the USB stick.To upload the settings you have to select each item separately, press "cursor right" (or the "OK button), confirm with "OK" and wait until "Done" appears. In case the download to the USB stick was not successful "Failure" will appear. In this case, check if the USB stick is connected properly and if the directory "repair" is present in the root of the USB stick. Now the settings are stored onto your USB stick and can be used to download onto another TV or other SSB. Uploading is of course only possible if the software is running and if you have a picture. This method is created to be able to save the customer's TV settings and to store them into another SSB. Download from USB. To download several settings from the USB stick to the TV. Same way of working as with uploading. To make sure that the download of the channel list from USB to the TV is executed properly, it is necessary to restart the TV and tune to a valid preset if necessary. Note: The "History list item" can not be downloaded from USB to the TV. This is a "read-only" item. In case of specific problems, the development department can ask for this info.
·
· ·
·
How to Navigate · In SAM, you can select the menu items with the "CURSOR UP/DOWN" key on the RC-transmitter. The selected item will be highlighted. When not all menu items fit on the screen, move the "CURSOR UP/DOWN" key to display the next/previous menu items. · With the "CURSOR LEFT/RIGHT" keys, it is possible to: (De) activate the selected menu item. (De) activate the selected sub menu. · With the "OK" key, it is possible to activate the selected action. How to Exit SAM Use one of the following methods: · Press the "MENU" button on the RC-transmitter. · Switch the set to STAND-BY via the RC-transmitter.
EN 18
5.2.3
5.
Q528.2E LA
Service Modes, Error Codes, and Fault Finding
- the serial number of the SSB, which consists of seven digits. Both can be found on a sticker on the PWB of the SSB itself. The format of the identification number is then as follows: (total fourteen characters). Installed date. Indicates the date of the first installation of the TV. This date is acquired via time extraction. Digital Natural Motion. Gives the status of the Digital Natural Motion setting as set by the customer. Remark: a customer can choose between "OFF", "MINIMUM" and "MAXIMUM", but in CSM this item will only show "OFF" or "ON" ("ON" in case the customer has choosen "MINIMUM" or "MAXIMUM") Pixel Plus. Gives the last status of the Perfect Pixel HD setting, as set by the customer. Possible values are "ON" and "OFF". See DFU on how to change this item. DNR. Gives the last status of the Noise reduction setting, as set by the customer. Possible values are "OFF", "MINIMUM", "MEDIUM" and "MAXIMUM". See DFU on how to change this item. Noise Figure. Gives an indication of the signal quality for the selected transmitter. Possible values are "BAD", "AVERAGE", "GOOD" and "DIGITAL". In case of a digital channel, this item will never indicate: "BAD", "GOOD" or "AVERAGE" but only displays "DIGITAL". 12NC Display. Shows the 12NC of the display. Headphone Volume. Gives the last status of the headphone volume, as set by the customer. The value can vary from 0 (volume is minimum) to 100 (volume is maximum). See DFU on how to change this item. Surround Mode. Indicates the by the customer selected sound mode (or automatically chosen mode). Possible values are "STEREO" and "VIRTUAL DOLBY SURROUND". It can also have been selected automatically by signalling bits (internal software). See DFU on how to change this item. AVL. Indicates the last status of AVL (Automatic Volume Level) as set by the customer: See DFU on how to change this item. Delta Volume. Indicates the last status of the delta volume for the selected preset as set by the customer: from "-12" to "+12". See DFU on how to change this item. Volume. Indicates the last status of the volume for the selected preset as set by the customer: from "0" to "100". See DFU on how to change this item. Balance. Indicates the last status of the balance for the selected preset as set by the customer: from "-10" to "+10". See DFU on how to change this item. Preset Lock. Indicates if the selected preset has a child lock: "LOCKED" or "UNLOCKED". See DFU on how to change this item. Lock after. Indicates at what time the channel lock is set: "OFF" or e.g. "18:45" (lock time). See DFU on how to change this item. Parental rating lock. Indicates the "Parental rating" as set by the customer. See DFU on how to change this item. Parental rating status. Indicates the "Parental rating" as transmitted by the broadcaster (if applicable). If the parental rating status is indicating a higher age then the parental rating lock as set by the customer, you will need to enter the child lock code. TV ratings lock. Only applicable for US. Movie ratings lock. Only applicable for US. On timer. Indicates if the "On timer" is set "ON" or "OFF" and when it is set to "ON", also start time, start day and program number is displayed. See DFU on how to change this item. Location. Gives the last status of the location setting as set via the installation menu. Possible values are "SHOP" and "HOME". If the location is set to "SHOP", several settings are fixed. So for a customer location must be set to "HOME". Can be changed via the installation menu (see also DFU). HDMI key validity. Indicates if the HDMI keys (or HDCP keys) are valid or not. In case these keys are not valid and
Customer Service Mode (CSM) Purpose When a customer is having problems with his TV-set, he can call his dealer or the Customer Helpdesk. The service technician can then ask the customer to activate the CSM, in order to identify the status of the set. Now, the service technician can judge the severity of the complaint. In many cases, he can advise the customer how to solve the problem, or he can decide if it is necessary to visit the customer. The CSM is a read only mode; therefore, modifications in this mode are not possible. When in this chassis CSM is activated, a colour bar test pattern will be visible for 5 seconds. This test pattern is generated by the Pacific3. So if you see this test pattern you can determine that the back end video chain (Pacific3, LVDS, and display) of the SSB is working. In case of a set with DFI panel, an extra test picture is generated. So you will see the Pacific3 test picture for 3 seconds and then the DFI EPLD test picture for another 3 seconds. With this extra test picture you can determine if the DFI board is working properly. Also new in this chassis: when you activate CSM and there is a USB stick connected to the TV, the software will dump the complete CSM content to the USB stick. The file (Csm.txt) will be saved in the root of your USB stick. This info can be handy if you do not have picture. Another new item in this chassis is when CSM is activated, the complete error-buffer content will be shown via the blinking LED procedure. How to Activate CSM Key in the code "123654" via the standard RC transmitter. Note: Activation of the CSM is only possible if there is no (user) menu on the screen! How to Navigate By means of the "CURSOR-DOWN/UP" knob on the RCtransmitter, you can navigate through the menus. Contents of CSM · Set Type. This information is very helpful for a helpdesk/ workshop as reference for further diagnosis. In this way, it is not necessary for the customer to look at the rear of the TV-set. Note that if an NVM is replaced or is initialized after corruption, this set type has to be re-written to NVM. ComPair will foresee in a possibility to do this. · Production Code. Displays the production code (the serial number) of the TV. Note that if an NVM is replaced or is initialized after corruption, this production code has to be re-written to NVM. ComPair will foresee a in possibility to do this. · Code 1. Gives the last five errors of the error buffer. As soon as the built-in diagnose software has detected an error, the buffer is adapted. The last occurred error is displayed on the leftmost position. Each error code is displayed as a 2-digit number. When less than 10 errors occur, the rest of the buffer is empty (00). See also paragraph "Error Codes" for a description. · Code 2. Gives the first five errors of the error buffer. See also paragraph "Error Codes" for a description. · Options 1. Gives the option codes of option group 1 as set in SAM (Service Alignment Mode). · Options 2. Gives the option codes of option group 2 as set in SAM (Service Alignment Mode). · 12NC SSB. Gives an identification of the SSB as stored in NVM. Note that if an NVM is replaced or is initialized after corruption, this identification number has to be re-written to NVM. ComPair will foresee in a possibility to do this. This identification number consists of 14 characters and is built up as follows: - Seven last characters of the 12NC of the SSB itself.
· ·
·
·
·
· ·
·
·
·
·
·
·
·
· ·
· · ·
·
·
Service Modes, Error Codes, and Fault Finding
the customer wants to make use of the HDMI functionality, the SSB has to be replaced. Tuner frequency. Indicates the frequency the transmitter is tuned to. TV System. Gives information about the video system of the selected transmitter. In case a DVBT signal is received this item will also show ATSC. BG: PAL BG signal received DK: PAL DK signal received L/La: SECAM L/La signal received I: PAL I signal received M: NTSC M signal received ATSC: ATSC signal received DVB: DVBT signal received 12NC one zip SW. Displays the 12NC number of the onezip file as it is used for programming software in production. In this one-zip file all below software versions can be found. Initial main SW. Displays the main software version which was initially loaded by the factory. Current main SW. Displays the built-in main software version. In case of field problems related to software, software can be upgraded. As this software is consumer upgradeable, it will also be published on the Internet. Example: Q582E_1.2.3.4. Flash utils SW. Displays the software version of the software which contains all necessary components of the download application. To program this software, EJTAG tooling is needed. Example: Q582E_1.2.3.4. Standby SW. Displays the built-in stand-by processor software version. Upgrading this software will be possible via ComPair or via USB (see chapter Software upgrade). Example: STDBY_3.0.1.2. MOP SW. Only applicable for US. At the time of release of this manual, there was still a problem with this item, and some rubbisch was displayed. Ignore this. Pacific 3 Flash SW. Displays the Pacific 3 software version. NVM version. Displays the NVM version as programmed by factory. Display parameters. for development purposes only. Private PQ parameters. for development purposes only. Public PQ parameters. for development purposes only. Ambilight parameters. for development purposes only. Acoustics parameters. for development purposes only. DFI software (if applicable). Displays the DFI EPLD software. DFI ambilight software (if applicable). Displays the DFI ambilight EPLD software.
Q528.2E LA
5.
EN 19
· ·
·
· ·
·
·
·
· · · · · · · · ·
How to Exit CSM Press "MENU" on the RC-transmitter.
EN 20 5.3
5.
Q528.2E LA
Service Modes, Error Codes, and Fault Finding
due to overvoltage. It is recommended to measure first the FET 7U08 on short-circuit before activating SDM via the service pads. When the TV is in protection state due to an error detected by main software (MIPS protection) and SDM is activated via short-cutting the service pads on the SSB, the TV starts up and ignores the error. In this chassis, only error "63" (power-ok) is a MIPS protection and already displays the failure via blinking LED.
Stepwise Start-up
There are two possible situations: one for protections detected by the stand-by software and one for protections detected by the main software. When the TV is in a protection state due to an error detected by stand-by software (and thus blinking an error) and SDM is activated via short-circuiting the pins on the SSB, the TV starts up until it reaches the situation just before protection. So, this is a kind of automatic stepwise start-up. In combination with the start-up diagrams below, you can see which supplies are present at a certain moment. Important to know is, that if e.g. the 3V3 detection fails (and thus error 8 is blinking) and the TV is restarted via SDM, the Stand-by Processor will enable the 3V3, but will not go to protection now. The TV will stay in this situation until it is reset (Mains/AC Power supply interrupted). Caution: in case the start up in this mode with a faulty FET 7U08 is done, you can destroy all IC's supplied by the +3V3,
The abbreviations "SP" and "MP" in the figures stand for: · SP: protection or error detected by the Stand-by Processor. · MP: protection or error detected by the MIPS Main Processor.
Mains off
Mains on
- WakeUp requested - Acquisition needed - No data Acquisition required - tact SW pushed - last status is hibernate after mains ON
WakeUp requested
St by
- Tact switch Pushed - last status is hibernate after mains ON
Semi St by
Active
- St by requested - tact SW pushed
Tact switch pushed
WakeUp requested (SDM) GoTo Protection GoTo Protection
Hibernate
Protection
I_17960_061.eps 220508
Figure 5-3 Transition diagram
Service Modes, Error Codes, and Fault Finding
Q528.2E LA
5.
EN 21
Off
Mains is applied
Stand by or Protection
Standby Supply starts running. All standby supply voltages become available.
st-by µP resets
All I/O lines have a High default state: - Switch PNX8541 in reset (active LOW). - Keep the Audio-reset high. - NVM power line is high, no NVM communication possible.
If the protection state was left by short circuiting the SDM pins, detection of a protection condition during startup will stall the startup. Protection conditions in a playing set will be ignored. The protection mode will not be entered.
Initialise I/O pins of the st-by µP, start keyboard scanning, RC detection. Wake up reasons are off.
- Switch Audio-Reset high. It is low in the standby mode if the standby mode lasted longer than 10s.
Restart
PDPGO line is high (either HW wise in a non FHP set or because of the stby µP reset in an FHP set) which will start the FHP PDP.
Switch ON PSU supply by switching LOW the Standby I/O line.
+12V is switched on Wait 50ms and then start polling the DETECT 2 every 40ms.
DETECT 2 received within 2900 ms
No
12V supply" error 6
Yes activate DETECT 2 algorithm
SP
Enable-1V2 is reserved , not use in TV522-82M
Enable the +1V2 supply (ENABLE-1V2)
Wait 100ms Enable the supply for +3V3 and +5V (ENABLE-3V3) Start polling the detect 1 every 40ms
DETECT 1 = High within 250 ms after enable-3V3 toggle? Yes Activate DETECT 1 algorithms
No
Supply Fault = High?
Yes
Voltage output error: 8
No Standby line set to HIGH for 5 seconds
SP
Wait 20ms
SUPPLY-FAULT I/O line is High? Yes Enable the supply fault detection algorithm No
No
Detect 1 = High?
Yes
Supply fault error 9
No
SP
Set I²C slave address of Standby µP to (A0h)
Standby line set to HIGH for 5 seconds
Switch LOW the RESET-NVM_WP-NANDFLASH line. Add a 2ms delay before trying to address the NVM to allow correct NVM initialization.
This will allow access to NVM and NAND FLASH and can not be done earlier because the FLASH needs to be in Write Protect as long as the supplies are not available.
I_17960_062a.eps 230508
Figure 5-4 "Off" to "Semi Stand-by" flowchart (part 1)
EN 22
5.
Q528.2E LA
Service Modes, Error Codes, and Fault Finding
Yes Enable the supply fault detection algorithm No No
SP
Set I²C slave address of Standby µP to (A0h)
Standby line set to HIGH for 5 seconds
Switch LOW the RESET-NVM_WP-NANDFLASH line. Add a 2ms delay before trying to address the NVM to allow correct NVM initialization.
This will allow access to NVM and NAND FLASH and can not be done earlier because the FLASH needs to be in Write Protect as long as the supplies are not available.
Detect EJTAG debug probe (pulling pin of the probe interface to ground by inserting EJTAG probe)
An EJTAG probe (e.g. WindPower ICE probe) can be connected for Linux Kernel debugging purposes.
EJTAG probe connected ?
Yes
No
No
Cold boot?
Yes No Release AVC system reset Feed warm boot script Release AVC system reset Feed cold boot script Release AVC system reset Feed initializing boot script disable alive mechanism
This is still the timing of the Jaguar 2k6. Timing need to be updated if more mature info is available. No Bootscript ready in 1250 ms?
Yes Set I²C slave address of Standby µP to (60h)
RPC start (comm. protocol) This is still the timing of the Jaguar 2k6. Timing needs to be updated if more mature info is available. No Flash to Ram image transfer succeeded within 30s?
Code = 5 Yes This is still the timing of the Jaguar 2k6. Timing needs to be updated if more mature info is available.
Switch AVC PNX8541 in reset (active low)
Code = 53
No
SW initialization succeeded within 20s?
Wait 10ms
Yes
Enable Alive check mechanism Switch the NVM reset line HIGH. MIPS reads the wake up reason from standby µP. Wait until AVC starts to communicate
Disable all supply related protections and switch off the +2V5, +3V3 DC/DC converter.
In case of an LCD set, check the Power-OK display line Wait 5ms
switch off the remaining DC/DC converters
Power-ok display high?
No
Log power-ok error and enter protection
MP
3-th try?
Switch Standby I/O line high.
Yes Reset the Pacific by pulling LOW the Pacific hardware reset line during 100ms. No
Yes Blink Code as error code Release Pacific reset and wait 200ms
Ping the Pacific through I²C
SP
I_17960_062b.eps 230508
Figure 5-5 "Off" to "Semi Stand-by" flowchart (part 2)
Service Modes, Error Codes, and Fault Finding
Q528.2E LA
5.
EN 23
Yes Blink Code as error code Release Pacific reset and wait 200ms
Ping the Pacific through I²C
SP
Pacific acknowledges? No Third Pacific boot retry?
Yes
Yes
Initialize Pacific
Log Pacific error
Enable the Pacific output by sending the PanelConfig.PanelOn to the Pacific in case of a DFI set
Start 4 seconds preheating timer in case of an LPL scanning backlight LCD set.
This is needed here because the Pacific has to deliver an output clock towards the DFI. Otherwise the DFI cannot deliver ambilight functionality in the lampadaire mode. The presence of the DFI can be determined via the display option.
Initialize audio - Channeldecoder type TDA10060 cannot be reloaded without reset of the channeldecoder. - Channeldecoder type TDA10048 can be reloaded without reset.
No
Channel decoder TDA 10048?
Yes
Download firmware into the channel decoder
Release reset MPEG4 module: BOLT-ON-IO: High
No Downloaded successfully?
MPEG4 module will start booting autonomously. No
Third try?
Wait TBD ms Yes Yes initialize tuner, Master IF and channel decoder Log SW event: STi7100PorFailure
Log channel decoder error
POR polling positive?
No
Initialize source selection yes Wait until Cpipe delivers a stable output clock
Wait TBD ms
Important remark: Input vertical frequency changes (48/50/60Hz) detected during startup sequence should not be taken into account. The end situation should always be safeguarded. If not, these changes will lead to EPLD resets which will switch on the display and disturb the startup performance.
Reset EPLD
Wait 100ms
Reset Pacific clock
EPLD and Pacific should be reset when a stable input clock become s available at their input.
Start alive IIC polling mechanism
yes
POR polling positive?
No Alive polling bootSTi7100PorFailure: Log HW error 38 and generate cold boot
NOK
Initialize video processing IC's: - PNX5050 in /82 - scaler EPLD
Log SW event STi7100AliveFailedError and generate fast cold reboot eventually followed by a cold reboot.
initialize AutoTV by triggering CHS AutoTV Init interface
Initialize Pacific or EPLD related Ambilight settings (if applicable)
Initialize Ambilight with Lights off.
Because of a bug in the Pacific IC, all video and display related Pacific parameters should be initialized before initializing the ambilight related Pacific parameters. If not, initializing the video and display related Pacific parameters will overwrite the ambilight parameters.
Do not enter semi-standby state in case of an LPL scanning backlight LCD set before 4s preheating timer has elapsed.
Semi-Standby
Figure 5-6 "Off" to "Semi Stand-by" flowchart (part 3)
I_17960_062c.eps 230508
EN 24
5.
Q528.2E LA
Service Modes, Error Codes, and Fault Finding
Semi Standby
Wait until previous on-state is left more than 2 seconds ago. (to prevent LCD display problems)
action holder: AVC action holder: St-by autonomous action
Assert RGB video blanking and audio mute
Rewrite Pacific register 0x03 (output format) with TcuUpdate: this command is sometimes not processed properly by the Pacific at initialisation time, resending it here solves the issue.
Switch on the display by sending the PanelConfig.PanelOn (I²C) command to the Pacific
Initialize audio and video processing IC's and functions according needed use case.
wait 250ms (min. = 200ms)
Switch off the dimming backlight feature and make sure PWM output is set to 100%
Switch on LCD backlight
The higher level requirement is that audio and video should be demuted without transient effects and that the audio should be demuted maximum 1s before or at the same time as the unblanking of the video.
Wait until valid and stable audio and video, corresponding to the requested output is delivered by the AVC AND the backlight PWM has been on for 1second.
Switch Audio-Reset low and wait 5ms
Release audio mute and wait 100ms before any other audio handling is done (e.g. volume change)
Restore dimming backlight feature, PWM output and unblank the video.
Active
I_17960_063.eps 220508
Figure 5-7 "Semi Stand-by" to "Active" flowchart (non DFI)
Service Modes, Error Codes, and Fault Finding
Q528.2E LA
5.
EN 25
Active
Mute all sound outputs via softmute
action holder: AVC action holder: St-by autonomous action
Wait 100ms
Set main amplifier mute (I/O: audio-mute)
Force ext audio outputs to ground (I/O: audio reset) And wait 5ms
switch off LCD backlight
Mute all video outputs
Wait 250ms (min. = 200ms)
Switch off the display by sending the PanelConfig.PanelOff (I²C) command to the Pacific
switch off ambient light
Semi Standby
I_17960_064.eps 220508
Figure 5-8 "Active" to "Semi Stand-by" flowchart (non-DFI)
EN 26
5.
Q528.2E LA
Service Modes, Error Codes, and Fault Finding
Semi Stand by
If ambientlight functionality was used in semi-standby (lampadaire mode), switch off ambient light (see CHS ambilight)
Delay transition until ramping down of ambient light is finished. *)
*) If this is not performed and the set is switched to standby when the switch off of the ambilights is still ongoing, the lights will switch off abruptly when the supply is cut.
transfer Wake up reasons to the Stand by µP.
Switch Memories to self-refresh (this creates a more stable condition when switching off the power).
Switch AVC system in reset state
Wait 10ms
Switch the NVM reset line HIGH.
Disable all supply related protections and switch off the DC/DC converter (via the Enable-3V3 I/O line)
Wait 5ms
switch off the +1V2 DC/DC converters
Switch OFF all supplies by switching HIGH the standby I/O line..
Important remark: release reset audio 10 sec after entering standby to save power
Stand by
I_17960_065.eps 220508
Figure 5-9 "Semi Stand-by" to "Stand-by" flowchart
Service Modes, Error Codes, and Fault Finding
Q528.2E LA
5.
EN 27
MP
action holder: MIPS action holder: St-by autonomous action Redefine wake up reasons for protection state and transfer to stand-by µP. Log the appropriate error and set stand-by flag in NVM
SP
Switch off LCD lamp supply
Wait 250ms (min. = 200ms)
Switch off LVDS signal
Switch off 12V LCD supply within a time frame of min. 0.5ms to max. 50ms after LVDS switch off.
Ask stand-by µP to enter protection state
Switch AVC in reset state
Wait 10ms
Switch the NVM reset line HIGH.
Disable all supply related protections and switch off the +1V8 and the +3V3 DC/DC converter.
Wait 5ms
switch off the +1V2 DC/DC converter
Switch OFF all supplies by switching HIGH the Standby I/O lines.
Flash the Protection-LED in order to indicate protection state*
(*): This can be the standby LED or the ON LED depending on the availability in the set under discussion.
I_17960_066.eps 220508
Protection
Figure 5-10 "Protection" flowchart
EN 28
5.
Q528.2E LA
Service Modes, Error Codes, and Fault Finding
supply detection algorithms for DC-DC outputs
Polling every 40ms
No
DETECT 1 = Low ?
Yes Check DETECT1 5 times ( within 500us ) Yes
No
DETECT 1 = Low ? 5 consecutive times ?
Shutdown ( Active to Semistdby to standby )
Wait for 5 seconds
Restart
I_17960_067.eps 220508
Figure 5-11 "Supply detection algorithm for DC-DC outputs" flowchart
supply fault detection algorithm
N0
SUPPLY-FAULT = LOW for 1ms ?
Yes
No Shutdown ( Active to Semistdby to standby )
DETECT1 = High ?
Yes Error 9
Wait for 5 seconds
Restart
SP
I_17960_068.eps 220508
Figure 5-12 "Supply fault detection algorithm" flowchart
Service Modes, Error Codes, and Fault Finding
Q528.2E LA
5.
EN 29
+12V supply detection algorithm. See CHS protections.
Polling every 40ms
No
DETECT 2 = Low ?
Yes Check DETECT2 5 times ( within 500us) Yes
No
DETECT 2 = Low ? 5 consecutive times ?
Shutdown ( Active to Semistdby to standby )
Wait for 5 seconds
Restart
I_17960_069.eps 220508
Figure 5-13 "+12 V supply detection algorithm" flowchart
EN 30 5.4
5.4.1
5.
Q528.2E LA
Service Modes, Error Codes, and Fault Finding 5.5
5.5.1
Service Tools
ComPair Introduction ComPair (Computer Aided Repair) is a Service tool for Philips Consumer Electronics products. and offers the following: 1. ComPair helps you to quickly get an understanding on how to repair the chassis in a short and effective way. 2. ComPair allows very detailed diagnostics and is therefore capable of accurately indicating problem areas. You do not have to know anything about I2C or UART commands yourself, because ComPair takes care of this. 3. ComPair speeds up the repair time since it can automatically communicate with the chassis (when the uP is working) and all repair information is directly available. 4. ComPair features TV software up possibilities. Specifications ComPair consists of a Windows based fault finding program and an interface box between PC and the (defective) product. The (new) ComPair II interface box is connected to the PC via an USB cable. For the TV chassis, the ComPair interface box and the TV communicate via a bi-directional cable via the service connector(s). How to Connect This is described in the ComPair chassis fault finding database.
TO TV
TO UART SERVICE CONNECTOR TO I2C SERVICE CONNECTOR TO UART SERVICE CONNECTOR
Error Codes
Introduction The error code buffer contains all detected errors since the last time the buffer was erased. The buffer is written from left to right, new errors are logged at the left side, and all other errors shift one position to the right. When an error occurs, it is added to the list of errors, provided the list is not full. When an error occurs and the error buffer is full, then the new error is not added, and the error buffer stays intact (history is maintained). To prevent that an occasional error stays in the list forever, the error is removed from the list after more than 50 hrs. of operation. When multiple errors occur (errors occurred within a short time span), there is a high probability that there is some relation between them. Basically there are three kinds of errors: · Errors detected by the Stand-by software. These errors will always lead to protection and an automatic start of the blinking LED for the concerned error (see paragraph "The Blinking LED Procedure"). In these cases SDM can be used to start up (see chapter "Stepwise Start-up"). Note that it can take up to 90 seconds before the TV goes to protection and starts blinking the error (e.g. error 53) · Errors detected by main software that lead to protection. In this case the TV will go to protection and the front LED should also blink the concerned error. See also paragraph "Error Codes" -> "Error Buffer" -> "Extra Info". For this chassis only error 63 is a protection error detected by main software. · Errors detected by main software that do not lead to protection. In this case the error will be logged into the error buffer and can be read out via ComPair, via blinking LED method, or in case you have picture, via SAM.
ComPair II RC in RC out
Multi function
Optional Power Link/ Mode Switch Activity
I 2C
RS232 /UART
5.5.2
PC
How to Read the Error Buffer Use one of the following methods: · On screen via the SAM (only if you have a picture). E.g.: 00 00 00 00 00: No errors detected 06 00 00 00 00: Error code 6 is the last and only detected error 09 06 00 00 00: Error code 6 was first detected and error code 9 is the last detected error · Via the blinking LED procedure (when you have no picture). See next paragraph. · Via ComPair. · Via CSM. when CSM is activated the blinking LED procedure will start and the CSM content will be written to a USB stick (if present).
ComPair II Developed by Philips Brugge
HDMI I2C only
Optional power 5V DC
E_06532_036.eps 150208
Figure 5-14 ComPair II interface connection Caution: It is compulsory to connect the TV to the PC as shown in the picture above (with the ComPair interface in between), as the ComPair interface acts as a level shifter. If one connects the TV directly to the PC (via UART), ICs will be blown! How to Order ComPair II order codes: · ComPair II interface: 3122 785 91020. · ComPair32 CD (update): 3122 785 60160. · ComPair RS232 cable: 3104 311 12742 (to be used with chassis Q52x). Note: If you encounter any problems, contact your local support desk. 5.4.2 LVDS Tool Support of the LVDS Tool has been discontinued. 5.5.3
How to Clear the Error Buffer Use one of the following methods: · By activation of the "RESET ERROR BUFFER" command in the SAM menu. · With a normal RC, key in sequence "MUTE" followed by "062599" and "OK". · If the content of the error buffer has not changed for 50+ hours, it resets automatically.
5.5.4
Error Buffer In case of non-intermittent faults, clear the error buffer before you begin the repair (before clearing the buffer, write down the content, as this history can give you significant information). This to ensure that old error codes are no longer present. If possible, check the entire contents of the error buffer. In some situations, an error code is only the result of another error
Service Modes, Error Codes, and Fault Finding
code and not the actual cause (e.g., a fault in the protection detection circuitry can also lead to a protection). There are several mechanisms of error detection: · Via error bits in the status registers of ICs. · Via polling on I/O pins going to the stand-by processor. · Via sensing of analogue values on the stand-by processor or the PNX85xx. · Via a "not acknowledge" of an I2C communication. Take notice that some errors need more than 90 seconds before they start blinking or before they will be logged. So in case of problems wait 2 minutes from start-up onwards, and then check if the front LED is blinking or if an error is logged. Table 5-2 Error code overview
Error Description 3 5 I2C3 PNX85xx does not boot (HW cause) 5V, 12V supply 1V2, 1V4, 2V5, 3V3 supply Supply fault I2C-MUX1 I2C-MUX2 PNX5050 HDMI mux I2C switch Master IF MOP (Ambilight MOP on DFI panel)1) Tuner Error/ Detected Device Prot by E E MIPS Stby P PNX85xx PNX85xx Result Error logged. Error blinking.
Q528.2E LA
5.
EN 31
·
·
· ·
6 8 9 11 12 22 23 24 26 28
P P P E E E E E E E
Stby P Stby P Stby P MIPS MIPS MIPS MIPS MIPS MIPS MIPS
/ / / PCA9540 PCA9540 PNX5050 AD8190/ AD8191 PCA9540 TDA9898/ 9897/9890 EP2CXXF4 84C7N TD1716 TDA10060/ TDA10048 T6TF4 PNX85xx
Protection + Error blinking. Protection + Error blinking. Protection + Error blinking. Error logged. Error logged. Error logged. Error logged. Error logged. Error logged. Error logged.
·
·
·
34 37 46 53
E
MIPS MIPS MIPS Stby P
Error logged. Error logged. Error blinking + Error logged. Error blinking.
Channel decoder E Pacific3 PNX85xx does not boot (SW cause) Power OK E E
·
63
E/P
MIPS
/
Error logged in case of a PDP set. Protection in case of an LCD set. Error blinking + Error logged.
65
DFI (EPLD on DFI panel)1)
E
MIPS
/
Note 1). Where applicable. Extra Info · Rebooting. When a TV is constantly rebooting due to internal problems, most of the time no errors will be logged or blinked. This rebooting can be recognized via a ComPair interface and Hyperterminal (for Hyperterminal settings, see paragraph "Stand-by software upgrade). You will see that the loggings which are generated by the main software keep continuing. In this case (rebooting) diagnose has to be done via ComPair. · Error 3 (I2C bus 3 blocked). At the time of release of this manual, this error was not working as expected (error 3 is logged and can be read out). Current situation: when this error occurs, the TV will constantly reboot due to the blocked bus. The best way for further diagnosis here, is to use ComPair (e.g. read out the NVM content). Instead of error "3" it is possible you will see error "2" in the error buffer. · Error 5 (PNX85xx doesn't boot). Indicates that the main processor was not able to read his boo