Text preview for : HarmanKardon-MA361 pwramp.pdf part of Harman/Kardon MA361 power amplifier
Back to : HarmanKardon-MA361 pwramp | Home
AUDIOACCESS
MA-361/MA-361CP
TWELVE CHANNEL DIGITAL AMPLIFIER
PRELIMINARY SERVICE MANUAL
Harman Consumer Group
250 Crossways Park Dr.
Woodbury, New York 11797
www.audioaccess.com
MA-361
Audioaccess Twelve Channel Digital
®
Amplifier
The Audioaccess MA-361 Twelve Channel
Digital Amplifier--designed, engineered
and manufactured by Madrigal in
Middletown, CT--will no doubt be recog-
nized as the finest amplifier available for
use in any dedicated multi-room system
application. The product of over two years
of development and research, the goals of
the MA-361 were clear: high power, low
distortion, quiet, cool operation, outstand-
amazingly cool, thanks to its highly efficient capabilities allows the installing dealer to
ing sonics and ease of installation not only
digital design. A modular layout permits custom tailor the sound in each zone to
with associated Audioaccess components, the installing dealer to easily replace indi- compensate for the different room acoustics
but also with other home and commercial vidual amplifier modules, should service throughout a residence, maximizing the
audio distribution systems. The trend ever be required. The MA-361 can be performance of each pair of speakers.
towards use of higher quality and larger configured for use in either mono or
speaker systems for custom installed appli-
stereo operation by means of dip-switch- Signal Sensing and Voltage Triggers
cations has created a need for power es on the rear panel of the amplifier. A The signal sensing capabilities of the
amplification offering both true higher simple bussing scheme allows audio MA-361 ensure that the amplifiers for a
power levels with low distortion. The signals to be routed to a single zone, given zone are only powered on when a
MA-361 is a category leading product thatselected zones, or all areas. To aid in both particular area is active, saving on energy
finally addresses the evolution of high the pre-wiring phase of the project and in consumption. Voltage triggers allow the
quality custom audio systems. final installation, a speaker termination MA-361 to automatically turn on accessory
board--available separately--allows the items such as a fan, or a separate device
Main Features dealer to complete the speaker wiring to when either the amplifier or a designated
Some of the main features of the MA-361 the termination board during the prelimi- zone is activated.
include a conservative power rating of nary phase of the project. Later, upon final
100 Watts per channel into 8 Ohms from installation, the termination board is then
20Hz-20kHz with all channels driven, plugged directly into a slot on the back of
7-band graphic equalization programma- the amplifier, minimizing the chances of
ble on a per-zone basis, signal sensing, wiring errors within the system.
and voltage triggers to activate main
power in each stereo zone of amplifica- 7-Band Graphic Equalization
tion. In normal use, the MA-361 runs The MA-361's 7-band graphic equalization Simply Ingenious
Volume/Tone Control Modules Flexible Installation Capabilities other RS-232 based systems, a separate
Optional Volume/Tone Control Modules, The MA-361 is designed for use not only application is available, which downloads
which plug into available slots inside the with Audioaccess systems, but also with amplifier configuration settings via the
amplifier, provide the dealer with the other Multi-room or RS-232 based systems. RS-232 port on the MA-361CP version.
ability to supply high power at very low The unit is programmed with the propri-
distortion levels to expansion rooms etary Installation Manager application Summary
within the multi-room system. A total of when it is used with other Audioaccess The combination of the MA-361's power
6 Volume/Tone Control Modules may be Multi-Room components. Configuration capabilities, sonic quality, features, program-
installed in the MA-361. settings are downloaded from a Windows ming ease, installation flexibility and
PC or laptop via the RS-485 communica- serviceability clearly sets the new standard
tion port on the MA-361. When used with for amplifiers within the multi-room category.
Features
L 6 built-in 7-Band Graphic EQ, one per zone Easy installation L Download project settings via serial port using
L Signal sensing L Simple built-in input bussing scheme, no con- Installation Manager application or dedicated
L Voltage trigger for each zone set with remov- figuration switches required stand-alone software
able screw terminal L Plug-in TI-501 Speaker Termination Board, a Robust design
L Available in two versions: MA-361 with RS-485 snap for advance installations (available sepa- L Low voltage standby (brown out protection)
port and MA-361CP with RS-232 port rately, not included with amplifier) L Short circuit protection
L Optional modules configured by Audioaccess Modular construction L Thermal cutoff protection
Installation Manager application or stand-alone L Amplifier modules may be replaced quickly L Soft clipping
PC program and easily L Quiet, convection cooling (when properly
L Dual-color LED status indicator on front panel L Permits installation of optional modules installed according to factory recommenda-
illuminates Green for normal operation, Red for Upgradeable tions)
standby and a flashing Red for DC and/or ther- L Firmware upgradeable L UL/CSA/CE approved
mal protection L Optional EM-401 Volume/Tone Control mod-
L AC mains switch on front panel ule for all six zones (available separately)
Specifications
Number of Channels: Bandwidth: Dimensions:
L 12, configured as 6 left/right mono or L 60kHz at rated power, 8 load L 171/4"W x 51/8"H x 175/8"D
stereo pairs (zones) Signal/Noise: (438 mm x 130 mm x 448 mm)
Power Output: L 97dB unweighted (ref: rated power) into 8 (with connectors & feet)
L 100 Watts @ 8 , from 20Hz 20kHz, Crosstalk: Weight:
all channels driven L -84 dB between any two channels L 110 Volt Amplifier: 48 lb (21.8 kg)
130 Watts @ 4 , from 20Hz 20kHz, (no audible crosstalk) 230 Volt Amplifier: 51 lb (23.2 kg)
all channels driven Protection: Features, specifications and dimensions are subject to change.
200 Watts @ 4 , from 20Hz 20kHz, L Short Circuit, Over Current, DC, Thermal
single channels driven and Undervoltage
Efficiency: Muting:
L 93% @ 100 Watts/8 L Turn-on, Turn-off, Signal Sensing and
THD & Noise: Triggered per zone A Harman International Company
L < 0.3%, 0.1 Watt 200 Watts, 4 Input Impedance: Audioaccess®
IMD: L 20K Madrigal Audio Laboratories, Inc.
L 0.26% @ 4, 200 Watts Input Sensitivity: P.O.Box 781
Frequency response: L 1.3 Volt for full output 4 or 8 Middletown, CT 06457-0781
Internet: www.madrigal.com
L ± 0.3 dB at rated power, 8 load Gain: Fax: 860.346.1540 ©2002 Madrigal Audio Laboratories, Inc.
L 27dB 20201AA SS/MA-361
FEATURES
The Audioaccess MA-361 Twelve Channel Digital Amplifier designed, engineered and manufactured by Madrigal in
Middletown, CT represents the product of over two years of research and development.
As the inventor of the 12 channel amplifier category, Audioaccess has reinvented this category with the introduction of the
MA-361. The goals for the MA-361 were clear: high power, low distortion, quiet, cool operation, outstanding sonics and
ease of installation, when used not only in Audioaccess systems, but also with other home and commercial audio
distribution systems. The trend towards higher quality and larger speakers for custom installed applications has created a
need for this amp. We believe you will agree that the MA-361 is the first in an entirely new class of twelve channel
amplifiers.
Unique features
The main features of the MA-361 include a conservative power rating of 100 Watts per channel into 8 Ohms from 20Hz-
20kHz with all channels driven at 93% efficiency. This amazing efficiency not only minimizes power consumption, it also
runs surprisingly cool. Other unique features include programmable 7-band graphic EQ (set by the installer via PC) for
each zone and optional plug-in stereo Volume/Tone Control Modules, which pro-vide volume control in Expansion
rooms/sub zones within an Audioaccess system or another RS-232 based control system. The modular layout permits the
dealer to easily replace individual amplifier modules should service ever be required. An external speaker termination
board can be ordered in advance to allow termination of loudspeakers before the amplifier is delivered for final installation.
At final, simply plug the speaker termination board onto the rear panel of the amplifier.
Other features
To make the amplifier specifically attractive for use in whole-house audio distribution, we have included specific features
to ensure reliable and easy installation. Signal sensing and voltage triggers activate the main power in each stereo zone
of amplification. Dip switches on the rear-panel configure the MA-361 for use in either mono or stereo operation. A simple
bussing scheme allows audio signals to be routed into a single zone, selected zones, or all areas.
7-Band Graphic Equalization
The MA-361's 7-band graphic equalization capabilities allows the installing dealer to custom tailor the sound in each zone
to compensate for the different room acoustics throughout a residence, maximizing the performance of each pair of
speakers. This is accomplished by using the Audioaccess Installation Manager Software application (or stand-alone
application) running on the dealer's PC or laptop.
Signal Sensing and Voltage Triggers
The signal sensing capabilities of the MA-361 ensure that the amplifiers for a given zone are only powered on when a
particular area is active, saving on energy consumption. Voltage triggers allow the MA-361 to automatically turn on
accessory items such as a fan, or a separate device when either the amplifier or a designated zone is activated.
Volume/Tone Control Modules
Optional Volume/Tone Control Modules, which plug into available slots inside the amplifier, provide the ability to supply
high power at very low distortion levels to expansion rooms within the multi-room system. The user may control the
volume in rooms with Audioaccess keypads and touchscreens, or by using ANY other touch screen/control systems. A
total of 6 Volume/Tone Control Modules may be installed in the MA-361.
Flexible Installation Capabilities
The MA-361 is designed for use with Audioaccess systems, as well as other Multi-room or RS-232 based systems. The
unit is programmed with the proprietary Installation Manager application when it is used with other Audioaccess Multi-
Room components. Configuration settings are downloaded from a Windows PC or laptop via the RS-485 communication
port on the MA-361. When used with other RS-232 based systems, a separate application is available, which downloads
amplifier configuration settings via the RS-232 port on the MA-361CP version.
Summary
The MA-361's combination of power capabilities, sonic quality, features, programming ease, installation flexibility and
serviceability clearly sets the new standard for amplifiers within the multi-room category.
Specifications:
· Number of Channels: 12, configured as 6 left/right mono or stereo pairs (zones)
· Power Output: 100 Watts @ 8 ohms, from 20Hz -- 20kHz, all channels driven
· 130 Watts @ 4 ohms, from 20Hz -- 20kHz, all channels driven
· 200 Watts @ 4 ohms, from 20Hz -- 20kHz, two channels driven
· Efficiency: 93% @ 100 Watts/8 ohms
· THD & Noise:< 0.3%, 0.1 Watt -- 200 Watts, 4 ohms IMD:-0.26% @ 4 ohms 200 Watts
· Frequency response: ± 0.3 dB at rated power, 81Ú2 load
· Bandwidth: 60kHz at rated power, 81Ú2 load
· Signal/Noise: 97dB unweighted (ref: rated power) into 8 1Ú2
· Crosstalk: -84 dB between any two channels (no audible crosstalk)
· Protection:Short Circuit, Over Current, DC, Thermal and Undervoltage
· Muting: Turn-on, Turn-off, Signal Sensing and Triggered per zone
· Input Impedance: 20K
· Input Sensitivity: 1.3 Volt for full output 4 or 81Ú2
· Gain: 27dB
· Dimensions: 17 1/4"W x 5 1/8"H x 17 5/8"D (438 mm x 130 mm x 448 mm) (with connectors & feet)
· Weight:110 Volt Amplifier: 48 lb (21.8 kg), 230 Volt Amplifier: 51 lb (23.2 kg)
Features, specifications and dimensions are subject to change.
MA-361 AUDIO BOARD REMOVAL AND ASSEMBLY INSTRUCTIONS
Madrigal Audio Laboratories
P.O. Box 781
Middletown, CT 06457-0781
(860) 346-0896 FAX (860) 347-6251 # A041102
Audioaccess AUDIO BOARD DISASSEMBLY INSTRUCTIONS
APRIL 15, 2002 A041102
Table of Contents
Overview.................................................................................................................................................. 3
Affected Units .......................................................................................................................................... 3
Cautions before Beginnning ................................................................................................................... 3
Tools Required ......................................................................................................................................... 3
Disassembly/Reassembly Steps.............................................................................................................. 4
Removal/Assembly Sheets ....................................................................... "A" Process Description Sheets
Step 1 Remove Top Cover......................................................................................................... A000010P265
Step 2 Remove Larger PCP Clamp Assembly ............................................................................ A000010P245
Step 3 Remove First Graphic EQ PCB....................................................................................... A000010P210
Step 4 Remove Second Graphic EQ PCB .................................................................................. A000010P205
Step 5 Remove Screws Holding RS-232/485 PCB ...................................................................... A000010P200
Step 6 Remove RS-232 PCB (CP Model Specific)....................................................................... A000010P190
Step 7 Remove RS-485 PCB (Standard MA 361 Specific)............................................................ A000010P185
Step 8 Remove Amp Module Clamp Assembly........................................................................... A000010P180
Step 9 Remove Outer Ribbon to Audio Output PCB .................................................................... A000010P170
Step 10 Remove Inner Ribbon to Audio Output PCB.................................................................... A000010P165
Step 11 Remove Screws on Audio Output PCB ........................................................................ A000010P160A
Step 12 Remove Audio Output PCB .......................................................................................... A000010P155
Step 13 Remove Audio Modules................................................................................................ A000010P150
Step 14 Remove Audio Module Signal Cables ............................................................................ A000010P135
Step 15 Remove Audio Module Power Cables ............................................................................ A000010P130
Step 16 Remove Volume Bypass Jumpers ................................................................................. A000010P125
Step 17 Remove 20 Pin Ribbon Cable...................................................................................... A000010P120A
Step 18 Remove 40 Pin Ribbon Cable...................................................................................... A000010P115A
Step 19 Disconnect Connector on Audio Board P1 ..................................................................... A000010P110
Step 20 Disconnect Cable on Audio Board to RCA Input Board.................................................... A000010P105
Step 21 Remove Screws on Audio Board1 ................................................................................. A000010P095
Step 22 Remove Back Panel Screws......................................................................................... A000010P092
MA-361 Disassembly Instructions Page 2
Audioaccess AUDIO BOARD DISASSEMBLY INSTRUCTIONS
APRIL 15, 2002 A041102
Overview
The following procedure will allow a qualified Audioaccess Distributor to successfully remove and
reinstall the MA-361 Audio Board. New replacement audio boards shipped April 2002 eliminate a
problem where keypad messages may be heard as pops in Zones 1, 2 , 3 and 4 in affected units. In
addition, the signal sensing sensitivity was lowered to avoid audio from shutting off during low passages
of music if the amplifier is configured to turn on with Signal Sensing.
Affected Units
MA-361's manufactured before the serial numbers listed below should receive an updated Audio Board.
Starting Serial Numbers
Updated Audio Boards
Domestic Units 361u1073
Export Units 361e1018
Cautions! Before Beginning
CAUTION!
Hazardous voltages available inside unit. Before proceeding, remove AC cable from
AC outlet.
CAUTION!
Static sensitive parts and subassemblies inside unit. A static protection wrist strap
must be worn when touching static sensitive components. Please follow wrist strap
manufacturers' instructions for proper use.
Tools Required
o #2 Phillips Screwdriver
o 3/32" Hex Driver
o Needle Nose Pliers
MA-361 Disassembly Instructions Page 3
Audioaccess AUDIO BOARD DISASSEMBLY INSTRUCTIONS
APRIL 15, 2002 A041102
Disassembly/Reassembly Steps
The Disassembly steps are depicted in the process sheets and are identified below in Steps 1 through 22.
Instructions on each step are included in the process sheet for each step. In addition, some notes are provided below
to clarify a step for either Assembly or Reassembly.
Once the Audio Board has been extracted, repeat each step below in a backwards order from Step 22 through Step 1
when installing the replacement Audio Board.
Step Number Description Process Sheet Number
Step 1 Remove Top Cover.......................................................................................... A000010P265
Step 2 Remove Larger PCP Clamp Assembly ............................................................. A000010P245
Step 3 Remove First Graphic EQ PCB........................................................................ A000010P210
Step 4 Remove Second Graphic EQ PCB ................................................................... A000010P205
Step 5 Remove Screws Holding RS-232/485 PCB ....................................................... A000010P200
Step 6 Remove RS-232 PCB (CP Model Specific)........................................................ A000010P190
This step is used for MA-361CP units only.
Step 7 Remove RS-485 PCB (Standard MA 361 Specific)............................................. A000010P185
This step is used for the standard MA-361.
Step 8 Remove Amp Module Clamp Assembly............................................................ A000010P180
Note the "Dimples" or "Notches" on each end of the amp Clamp Assembly. When re-
installing this clamp, assure that these "dimples" are reinstalled in the same direction as
when removed.
Step 9 Remove Outer Ribbon to Audio Output PCB ..................................................... A000010P170
Step 10 Remove Inner Ribbon to Audio Output PCB....................................................... A000010P165
Step 11 Remove Screws on Audio Output PCB ...........................................................A000010P160A
When reassembling, these screws must be tight for grounding purposes before AC
power is applied.
Step 12 Remove Audio Output PCB ............................................................................. A000010P155
Step 13 Remove Audio Modules................................................................................... A000010P150
Step 14 Remove Audio Module Signal Cables ............................................................... A000010P135
Step 15 Remove Audio Module Power Cables ............................................................... A000010P130
Step 16 Remove Volume Bypass Jumpers .................................................................... A000010P125
These Jumpers are present whenever the Volume Tone Modules, EM401, are not used.
Remove these jumpers and install in the replacement Audio Board.
Step 17 Remove 20 Pin Ribbon Cable.........................................................................A000010P120A
Step 18 Remove 40 Pin Ribbon Cable.........................................................................A000010P115A
Step 19 Disconnect Connector on Audio Board P1 ........................................................ A000010P110
Disconnect only the connector on the Audio Board PCB. Do not disconnect connector on
Power Supply or Controller PCB.
Step 20 Disconnect Cable on Audio Board to RCA Input Board....................................... A000010P105
Step 21 Remove Screws on Audio Board ...................................................................... A000010P095
Step 22 Remove Back Panel Screws............................................................................ A000010P092
MA-361 Disassembly Instructions Page 4
MA361/M361CP
Electrical/Mechanical Parts Lists
Note:
These parts lists may contain some part
numbers that are not valid, or No Longer
Available.
Descriptions and Reference Designators,
when included, should aid technicians in part
substitution.
If necessary, call the Parts department at
1-516-496-3400 ext. 6553 for assistance.
MA-361 MAIN PARTS LIST
Part Number Description QTY Manufacturer Comments
CAP LYTIC 47U 20% 16V SMT PAN. EEV-
200256 HB1C470 1 PANASONIC-EEV-HB1C470
C2
ICS DIG ADM202EARN RS232 DRV/RCVR
760225 SMD 1 ANALOG DEVICES-ADM202JRN
U1
327-01009-00 CONN D_SUB 9PIN PCMT 745781-4 9PIN FEM
DS 1 AMP- 745781-4 USED IN PX700
P1
220189 CAP EMI 10N 30% 50V RADIAL PAN. EXC-
CET103 2 PANASONIC-EXC-CET103
DF1 DF2
230109 CAP SMD .1UF 25V X7R CER 6 ANY MANUFACTURER
C1 C3 C4 C5 C6 C7
205-70200-00 DIODE, TVS, 600W, UNI-DIR, 20V, SMT 2 MOTOROLA- 1SMB20AT3 MFG'S P/N CORRECTED
ESD1 ESD2
320-50003-00 SAMTEC HEADER 2X3 1 SAMTEC- TSW-103-07-G-D ADDED- ECN3008
P3
320-59902-00 SHUNT JUMPER 1X2 2 3M- 929950-00 ADDED- ECN3008
INSTALL IN DTE
P3 POSITION-
PER REVISED ASS'Y
DWG 943321B- ECN3105
CONN HEADER 14PIN PCMT TSW-107-08-T-D-
E01535 RA .1SP D/R R/A 1 SAMTEC TSW-107-08-T-D-RA NO GOLD!
330708 P1
612-18190-00 BRACKET, PC MNT SCREW TERM, 8190 (NO KEYSTONE- 8190 NO SCREW
SCREW) 2
MT1 MT2
580646A PCB MA361 RS232 1 PER DWG# 943320B DRILL CHART WAS 580646- ECN3007
BD FILENAME: 580646A.ZIP
Part Number Description QTY Manufacturer Comments
100774 RES SMT 330R 5% 1/10W 0805 14 ANY APPROVED
R1 R10 R13 R14 R15 R16 R2 R3 R4 R5 R6
R7 R8 R9
C1, C4, C7, C10, C13,
230145 CAP CER_X7R 100N 5% 50V SMT 0805 14 ANY APPROVED C16, C19, C22, C25, C28
C31, C34, C37, C40
C1 C4 C7 C10 C13 C16 C19 C22 C25 C28 ADDED- ECN3043
C31 C34 C37 C40
C1, C4, C7, C10, C13,
230150 CAP CER_X7R 1N0 5% 100V SMT 0805 28 ANY APPROVED C16, C19, C22, C25, C28
C31, C34, C37, C40
C11 C12 C14 C15 C17 C18 REMOVED- ECN3043
C2 C20 C21 C23 C24 C26 C27
C29 C3 C30 C32 C33 C35 C36
C38 C39 C41 C42 C5 C6
C8 C9
For RCA to Audio cable per
310101 WIR 26 COND FLAT RIBBON GREY 3 AMPHENOL- 843-191-2801-126 dwg# C000024
AMPHENOL- 843-191-2801-026
For RCA to Audio cable per
330337 CON LNMT 26PIN .1SP SOCKET IDC 1 AMP- 2-216408-6 dwg# C000024
For RCA to Audio cable per
330339 CON PCMT 26PIN .1SP DIP PLUG W/ LEGS 1 AMP- 111382-6 dwg# C000024
CONN RCA_F 3PIN PCMT RCA-151R-G RED
E01610 VERT MT RCA 7 Power Dynamics- 151W-G Gold plated
330166 P10 P12 P14 P2 P4 P6 P8
CONN RCA_F 3PIN PCMT RCA-151W-G
E01611 WHITE VERT MT RCA 7 Power Dynamics- 151R-G Gold plated
330165 P1 P11 P13 P3 P5 P7 P9
1 TBD
P15
MISC SWAGE 156 SWAGE 9/16"L RAF 3052-B-
E01631 632-B-37 6 RAF 3052-B-632-37
MT1 MT2 MT3 MT4 MT5 MT6
580656A PCB, RCA INPUT PX712 1 AS PER DWG# 943350A
BD ARTFILENAME- 580656A.ZIP
P/N Description QTY Manufacturer Comments
100506 RES SMT 22K1 1% 1/10W 0805 6 ANY MANUFACTURER
R1138 R338 R38 R538 R738 R938
100509 RES SMT 4K99 1% 1/10W 0805 1 ANY MANUFACTURER
R1224
ADDED R31, R32, R331,
100543 RES SMT 10M 1% 1/10W 0805 12 ANY MANUFACTURER R332, R531,
R532, R731, R732, R931,
R932,
R1131, R1132- ECN3104
100549 RES SMT 221R 1% 1/10W 0805 6 ANY MANUFACTURER
R1133 R33 R333 R533 R733 R933
ADDED R41, R341, R541,
100584 RES SMT 1K00 1% 1/10W 0805 34 ANY MANUFACTURER R741, AND
R941, R1141- WERE
R1117 R1118 R1139 R1301 R1303 R1305 E01501
R1307 R1309 R1311 R17 R18 R317 R318 ECN3104
R339 R39 R42 R44 R46 R47 R517 R518
R539
R717 R718 R739 R917 R918 R939
R41, R341, R541, R741, R941, R1141
100762 RES SMT 47K0 5% 1/10W 0805 6 ANY MANUFACTURER
R1013 R1213 R213 R413 R613 R813
100774 RES SMT 330R 5% 1/10W 0805 8 ANY MANUFACTURER
R1315 R1316 R1317 R1318 R1319 R1320
R43 R45
100783 RES SMT 3K32 1% 1/10W 0805 15 ANY MANUFACTURER
R1001 R1026 R1201 R1225 R1226 R1228
R1229 R201 R226 R401 R426 R601 R626
R801 R826
REMOVED R21, R25,
100787 RES SMT 20K0 1% 1/10W 0805 106 ANY MANUFACTURER R321, R325, R521,
R1 R10 R11 R1105 R1106 R1107 R1108 R525, R721, R725, R921,
R1109 R925, R1121,
R1110 R1111 R1112 R1113 R1114 R1119 R1125 -ECN3104
R1120 R1122 R1123 R1124
R1126 R1127 R12 R13 R14 R19 R2 R20
R22 R23 R24 R26 R27 R3 R305 R306
R307 R308 R309 R310 R311 R312 R313
R314
R319 R320 R322 R323 R324 R326
R327 R4 R5 R505 R506 R507 R508 R509
R510 R511 R512 R513 R514 R519 R520
R522 R523 R524 R526 R527 R6 R7
R705 R706 R707 R708 R709 R710 R711
R712
R713 R714 R719 R720 R722 R723 R724
R726 R727 R8 R9 R905 R906 R907
R908 R909 R910 R911 R912 R913 R914
R919
R920 R922 R923 R924 R926 R927
100789 RES SMT 100K 1% 1/10W 0805 12 ANY MANUFACTURER
R1002 R1027 R1202 R1227 R202 R227 R402
R427 R602 R627 R802 R827
ADDED R21, R25, R321,
100820 RES SMT 10K0 1% 1/10W 0805 103 ANY MANUFACTURER R325, R521,
R525, R721, R725, R921,
R1005 R1006 R1007 R1008 R1009 R1010 R925,
R1121, R1125- WERE
R1012 R1014 R1015 R1115 R1135 R1140 100787- ECN3104
R1205 R1206 R1207 R1208 R1209 R1210
R1212 R1214 R1215 R1302 R1304 R1306
R1308 R1310 R1312 R1313 R1314 R1321
R1322 R1323 R1324 R1325 R1326 R1327
R1328 R1329 R1401 R15 R205 R206 R207
R208 R209 R210 R212 R214 R215 R315
R335
R340 R35 R36 R40 R405 R406 R407 R408
R409 R410 R412 R414 R415 R515 R535
R540
R605 R606 R607 R608 R609 R610 R612
R614
R615 R715 R735 R740 R805 R806 R807
R808
R809 R810 R812 R814 R815 R915 R935
R940
R21 R25 R321 R325 R521 R525 R721 R725
R921 R925 R1121 R1125
CAP LYTIC 2U2 20% 35V SMT TANT PAN. WAS 200246 (PANASONIC-
E01755 ECS 6 PANASONIC- ECS-H1VC225R ECS-HIAC106R
C1302 C1304 C1306 C1308 C1310 C1312 ECN3104
CAP LYTIC 47U 20% 16V SMT PAN. EEV-
200256 HB1C470P 22 PANASONIC- EEV-HB1C470P
C1118 C1120 C1135 C18 C2 C20 C318 C320
C335 C35 C42 C45 C518 C520 C535 C718
C720 C735 C8 C918 C920 C935
230109 CAP CER_X7R 100N 10% 25V SMT 0805 213 ANY MANUFACTURER
C1 C10 C1001 C1002 C1003 C1004 C1006
C1007 C1008 C1009 C1010 C1011 C1012
C1014 C1109 C1110 C1112 C1113 C1117
C1119 C1121 C1122 C1123 C1126 C1127
C1130 C1131 C1138 C1139 C12 C1201
C1202
C1203 C1204 C1206 C1207 C1208 C1209
C1210 C1211 C1214 C1215 C1216 C13
C1301
C1303 C1305 C1307 C1309 C1311 C1313
C1314 C1315 C1316 C1317 C1401 C1402
C1403 C1404 C1405 C1406 C1407 C1408
C1409 C1410 C1411 C1412 C1413 C1414
C1415 C1416 C1417 C1418 C1419 C1420
C1421 C1422 C1423 C1424 C1425 C1426
C1427 C1428 C1429 C1430 C1431 C1432
C1433 C1434 C1435 C1436 C1501 C1502
C1503 C1504 C17 C19 C201 C202 C203
C204
C206 C207 C208 C209 C21 C210 C211 C212
C214 C22 C23 C26 C27 C30 C309 C31 C310
C312 C313 C317 C319 C321 C322 C323
C326
C327 C330 C331 C338 C339 C36 C4 C401
C402 C403 C404 C406 C407 C408 C409 C41
C410 C411 C43 C44 C46 C5 C509 C510
C512
C513 C517 C519 C521 C522 C523 C526
C527
C530 C531 C538 C539 C601 C602 C603
C604
C606 C607 C608 C609 C610 C611 C612
C614
C7 C709 C710 C712 C713 C717 C719 C721
C722 C723 C726 C727 C738 C739 C801
C802
C803 C804 C806 C807 C808 C809 C810
C811
C9 C909 C910 C912 C913 C917 C919 C921
C922 C923 C926 C927 C930 C931
CONN HEADER 26PIN PCMT mtsw-113-08-S-D
330707 340 .100" 1 SAMTEC TSW-113-07-T-D
P15
700123 DIODE MMBD914 SILICON SMT 1N914 30 MOTOROLA- MMBTD914LT1
CR1103 CR1104 CR1105 CR1301 CR1302
CR1303
CR1304 CR1305 CR1306 CR1307 CR1308
CR1309
CR1310 CR1311 CR1312 CR3 CR303 CR304
CR305 CR4 CR5 CR503 CR504 CR505
CR703
CR704 CR705 CR903 CR904 CR905
720023 DIODE 4N33 OPTO OPTO COUPLER 6 QT TECHNOLOGIES- 4N33
U1301 U1302 U1303 U1304 U1305 U1306
XISTOR MMBD3904LT1 NPN UNSORT SMD
720138 2N3904 25 MOTOROLA- MMBD3904LT1
Q1 Q1002 Q1003 Q1005 Q1102 Q1202
Q1203
Q1205 Q1401 Q202 Q203 Q205 Q302 Q402
Q403 Q405 Q502 Q602 Q603 Q605 Q702
Q802
Q803 Q805 Q902
WAS LM358 (780158)-
780214 IC LINEAR TL072CD DUAL OP AMP SOIC 31 Texas Instrument- TL072CD ECN3023
U1 U1102 U1104 U1105 U1106 U1107 U2 Motorola- TL072CD
U302 U304 U305 U306 U307 U4 U5 U502
U504 U505 U506 U507 U6 U7 U702 U704
U705 U706 U707 U902 U904 U905 U906
U907
780297 IC INA117KU ANA DIF AMP 12 BURR BROWN- INA117KU
U1001 U1002 U1201 U1202 U201 U202 U401
U402 U601 U602 U801 U802
320-55010-00 CONN HEADER 20PIN PCMT 102618-8 .1 2 AMP 103309-5
ROW SHD 3
P3 P4 P6
E00502 RES SMT 33K2 1% 1/10W 0805 24 ANY MANUFACTURER
R1018 R1023 R1128 R1129 R1218 R1223
R218 R223 R28 R29 R328 R329 R418 R423
R528 R529 R618 R623 R728 R729 R818
R823
R928 R929
CAP LYTIC 1U0 20% 50V SMT PA. EEV-
E00580 HA1H010R 6 PANASONIC-EEV-HA1H010R
C1132 C32 C332 C532 C732 C932
R31, R32, R331, R332,
E01023 RES SMT NU 1% 1/10W 0805 6 NOT USED R531,
R532, R731, R732, R931,
R1116 R16 R316 R516 R932,
R1131, R1132 are 10M
R716 R916 (100543)
ON SEMICONDUCTOR-
E01106 XISTOR MMBT3906 PNP SMD 2N3906 18 MMBT3906LT1
Q1001 Q1004 Q1103 Q1201 Q1204 Q2 Q201 DIODES INC- MMBT3906-7
Q204 Q303 Q401 Q404 Q503 Q601 Q604
Q703
Q801 Q804 Q903
DIODE LSS269-BO LED DO NOT USE
E01181 OBSOLETE 6 LEDTRONICS- SML 10R3-TR
LED1 LED2 LED3 LED4 LED5 LED6
IC SN74LVC573ADW DIG SMT OCTAL TI- CD74HC573M
E01346 LATCH 2
U1307 U1308
WAS 180R (E01395)-
100545 RES SMT 49R9 1% 1/10W 0805 1 ANY MANUFACTURER ECN3104
R37
REMOVED C33,C333,
E01503 CAP CER 18P0 10% 50V SMT 0805 62 ANY MANUFACTURER C533, C733,
C1005 C1013 C11 C1111 C1114 C1115
C1116 C933, C1133- ECN3104
C1124 C1125 C1128 C1129 C1205
C1213 C14 C15 C16 C205 C213 C24 C25
C28 C29 C3 C311 C314 C315 C316 C324
C325 C328 C329 C405 C413 C511
C514 C515 C516 C524 C525 C528 C529
C6 C605 C613 C711 C714 C715 C716 C724
C725 C728 C729 C805 C813 C911 C914
C915 C916 C924 C925 C928 C929
E01534 DIODE BZX84C5 ZENER 5.1V ZENER 4 DIODES INC- BZX84C5V1-7
CR1 CR1203 CR1204 CR2
612-18190-00 MISC HOLE 6-32 R/A SCREW TERMINAL 5 KEYSTONE- 8190
M10 M11 M7 M8 M9
E01636 IC CD4016BCM DIG QUAD SWITCH 3 FAIRCHILD- CD4016BCM
U3 U503 U903
E01638 IC LM339AM ANA QUAD COMP 9 NAT'L SEMICONDUCTOR- LM339AM
U1004 U1005 U1204 U204 U205 U404 U604
U605 U804
E01639 IC LM324AM ANA QUAD OPAMP 6 NAT'L SEMICONDUCTOR- LM324AM
U1003 U1203 U203 U403 U603 U803
E01641 RES SMT 475K 1% 1/10W 0805 24 ANY MANUFACTURER
R1016 R1017 R1021 R1022 R1216 R1217
R1221 R1222 R216 R217 R221 R222 R416
R417 R421 R422 R616 R617 R621 R622
R816
R817 R821 R822
CONN HEADER 8PIN PCMT B8B-PH-KL JST
E01644 .079 CTR 12 JST- B8B-PH-KL
P1L P1R P2L P2R P3L P3R P4L P4R P5L
P5R P6L P6R
CONN HEADER 4PIN PCMT 22-27-2041
E01645 MOLEX .1SP LOCKING 1 MOLEX- 22-27-2041
P1
CONN HEADER 12PIN PCMT 861912 MOLEX
E01646 5.08MM R/A 1 MOLEX- 861912
P2
CONN SOCKET 14PIN PCMT .1SP D/R
E01647 SOCKET 11 AMP 534998-7
P10 P11 P1V P2V P3V P4V P5V P6V P7 P8
P9
E01649 RES SMT 1M50 1% 1/10W 0805 6 ANY MANUFACTURER
R1134 R334 R34 R534 R734 R934
TOSHIBA- 2SC3326-B
NOT USED NOT USED 0 do not populate- ECN3023
Q3 Q4
E01651 CAP LYTIC 4U7 20% 16V SMT SMCAP4X4_3 6 PANASONIC- ECEV1CA4R7NR
C1137 C337 C37 C537 C737 C937
CONN HEADER 40PIN PCMT TST-120-01-T-D AMP 103309-8
E01696 D/R SHROUDED CABLE HDR 1
P5 SAMTEC TST-120-01-T-D
SWITCH THERMAL 70 DEGREES C
E01747 ENCAPSULATED THERMOSTAT 2 CANTHERM F11070151ZA0060 WAS- E01697- ECN
S1 S2 normally open- w/ NO PC Pins
CAP LYTIC NOT 20% USED SMT
E01700 SMCAP4X4_3 NU 6 NOT USED DO NOT INSTALL
C1134 C334 C34 C534 C734 C934
580643B PCB, AUDIO MA-361 1 PER DRILL CHART#943311B WAS 580643A- ECN3104
BD ART FILE- 580643B.ZIP
Part number Description QTY MANUFACTURER COMMENTS
230145 CAP SMD .1UF 50V 10% CER X7R 0805 24 ANY
C1-24
Part Number Description QTY Manufacturer Comments
100511 RES SMT 7K50 1% 1/10W 0805 12 ANY MANUFACTURER R304 R305 R4 R5
R1 R201 R203 R204 R205 R3 R301 R303 Ref des on wrong line,
R304 R305 R4 R5 restored
100561 RES SMT 1M00 1% 1/10W 0805 6 ANY MANUFACTURER
R2 R202 R206 R302 R306 R6
ADDED
R9,10,209,210,309,310
REMOVED
100765 RES SMT 1K00 5% 1/10W 0805 7 ANY MANUFACTURER R7,8,207,208,307,308
R10 R209 R210 R309 R310 R9 R404
ADDED
100774 RES SMT 330R 5% 1/10W 0805 6 ANY MANUFACTURER R7,8,207,208,307,308
R207 R208 R307 R308 R7 R8
ADDED C9 C2 C209 C202
100547 RES SMT 0R00 5% 1/10W 0805 6 ANY MANUFACTURER C309 C308
C9 C2 C209 C202 C309 C308
CAP LYTIC 47U 20% 16V SMT PAN. EEV- REMOVED C1 C10 C201
200256 HB1C470P 14 PANASONIC EEV-HB1C470P C210 C01 C310
C203 C205 C242 C245
C3 C303 C305 C342 C345 C410
C412 C42 C45 C5
CAP PESTR_FILM 2N2 5% 100V RADIAL FKP-
220047 2 6 WIMA- FKP2, 2200PF 100V 5%
C18 C218 C232 C318 C32 C332
220065 CAP PESTR_FILM 68N 5% 63V RADIAL MKS-2 6 WIMA- MKS2 .068UF 63V 5%
C17 C217 C231 C31 C317 C331
CAP PESTR_FILM 150N 5% 50V RADIAL
220076 WIMA MKS-02 6 WIMA- MKS02, .15UF, 50V, 5%
C15 C215 C229 C29 C315 C329
CAP PESTR_FILM 1N5 10% 63V RADIAL
220105 MKS02 3 WIMA- MKS02 1500PF, 63V, 10%
C224 C24 C324
220107 CAP PESTR_FILM 33N 5% 63V RADIAL MKS2 6 WIMA- MKS2, .033UF 63V 5%
C12 C212 C226 C26 C312 C326
220108 CAP PESTR_FILM 22N 5% 63V RADIAL MKS2 6 WIMA- MKS2, .022UF, 63V, 5%
C19 C219 C233 C319 C33 C333
CAP PESTR_FILM 330N 5% 63V RADIAL
220117 MKS2 6 WIMA- MKS2, .33UF, 63V, 5%
C13 C213 C227 C27 C313 C327
220119 CAP PESTR_FILM 1U0 5% 63V RADIAL MKS2 6 WIMA- MKS2 1UF 63V 5%
C11 C211 C225 C25 C311 C325
220121 CAP PESTR_FILM 3N3 5% 63V RADIAL FKP-2 12 WIMA- FKP2, 3300PF 63V 5%
C22 C222 C223 C23 C236 C237 C322 C323
C336 C337 C36 C37
REMOVED FOR
RESISTORS C9 C2 C209
230109 CAP CER_X7R 100N 10% 25V SMT 0805 32 ANY MANUFACTURER C202 C309 C308
C204 C206 C207 C208 C239
C240 C241 C243 C244 C246 C304 C306
C307 C308 C339 C340 C341 C343 C344
C346 C39 C4 C40 C41 C411 C413 C43 C44
C46 C6 C7 C8
CAP LYTIC NOT 20% USED SMT
E01707 SMCAP6_3X6_6 6 ANY MANUFACTURER NOT USED
C1 C10 C201 C210 C01 C310
230115 CAP CER_X7R 10N 10% 100V SMT 0805 6 ANY MANUFACTURER
C21 C221 C235 C321 C335 C35
230146 CAP CER_NPO 15N 5% 50V SMT 0805 6 ANY MANUFACTURER
C14 C214 C228 C28 C314 C328
was National LM358ADR-
780214 IC LTL072CD DUAL OP AMP SOIC 3 Fairchild- TL072CD ECN3023
U1 U201 U301 Motorola- TL072CD
145-4000110 CAP CER_X7R 1N5 5% 50V SMT 0805 3 ANY MANUFACTURER
C238 C338 C38
E01534 DIODE BZX84C5 ZENER 5.1V ZENER 6 DIODES INC- BZX84C51-7
CR1 CR2 CR201 CR202 CR301 CR302
CONN HEADER 14PIN PCMT TSW-107-08-T-D-
E01535 RA .1SP D/R R/A 2 SAMTEC- TSW-107-08-T-D-RA NOT GOLD
330708 P401 P402
E01616 CAP CER_X7R 6N8 10% 50V SMT 0805 6 ANY MANUFACTURER
C16 C216 C230 C30 C316 C330
E01677 CAP CER_NPO 820P 5% 50V SMT 0805 6 ANY MANUFACTURER
C20 C220 C234 C320 C334 C34
760176 IC LC7527E DIG 7B GRAPHIC CTRLR 3 SANYO LC7527E Special pin 1 placement!!!!
U2 U202 U302
580662A PCB MA361 GEQ2 BD 1 AS PER DWG# 943377A DRILL CHT.
580662A.ZIPBD ART FILE
Part Number Description QTY Manufacturer Comments
R16 REMOVED. DO NOT
100755 RES SMT 10K0 5% 1/10W 0805 18 ANY MANUFACTURER POPULATE
R1 R10 R11 R12 R13 R14 R15 R17 R2 ECN3036
R20 R22 R3 R4 R5 R6 R7 R8 R9
100774 RES SMT 330R 5% 1/10W 0805 2 ANY MANUFACTURER
R18 R19
CAP LYTIC 330U 20% 25V RADIAL NICHICON
200206 PL/PM SERIES 1 NICHICON- UPL1E331MPH
UPM series cap
equivalent added
C1 NICHICON- UPM1E331MPH ECN3138
200246 CAP LYTIC 10U 20% 10V SMT PAN. ECS 7 PANASONIC-ECSH1AC106R
C12 C15 C17 C22 C3 C7 C9
CAP EMI 10N 30% 50V RADIAL PAN. EXC-
220189 CET103U 1 PANASONIC- EXC-CET103U
DF1
230109 CAP SMD .1UF 25V X7R CER 12 ANY MANUFACTURER
C13 C14 C16 C18 C19 C2 C20 C21 C23 C4
C6 C8
330423 CONN HEADER 10PIN PCMT 102973-5 1 AMP- 102973-5 WAS 330137- ECN3007
P7
700123 DIODE MMBD914 SILICON SMT 1N914 1 MOTOROLA- MMBD914LT1
CR3 DIODES INC
230-30574-00 D FLIP FLOP, OCT 3STATE, 74HC574, SMT TEXAS INSTRUMENTS-
5 CD74HC574M
U4 U5 U6 U7 U8
320-55010-00 HEADER, 2X10, SHROUDED 1 AMP- 103309-5
P4
CONN HEADER 14PIN PCMT TEST .1"SP D/R EMULATOR
E01133 TPO 1 ANY MANUFACTURER CONNECTION
P6 PROTO USE ONLY
DIODE LSS269-BO LED SMT RED
E01181 1.8V@2mA 2 LEDTRONIICS SML 10R3-TR
710032 LED1 LED2
CONN HEADER 2PIN PCMT MOLEX 2PIN .1
E01311 SP LOCKING 22-27-2021 1 MOLEX- 22-27-2021
P1
230-30573-00 LATCH, OCTAL, TRI STATE, 74HC573, SMT TEXAS INSTRUMENTS-
2 CD74HC573M
U2 U3
E01505 CONN 5PIN B-5B-PH-K-S JST 2MM 1 JST- B-5B-PH-K-S
P3
E01503 CAP CER 18P0 10% 50V SMT 0805 2 ANY MANUFACTURER
C10 C11
E01504 IC COP8SBR9HVA8 MEM MPU 1 NATIONAL- COP8SBR9HVA8
760170 U1
CONN HEADER 40PIN PCMT TST-120-01-T-D
E01XXX .1SP SHROUDED SAMTEC 1 SAMTEC- TST-120-01-T-D NOT GOLD
P5
MISC CRYSTAL 9.216MHZ
E01509 HC49US9.216MABJ 1 CITIZEN- HC49US9.216MABJ
810056 X1
E01512 RES SMT 50R0 5% 1/10W 0805 1 ANY MANUFACTURER
R21
E01513 RES SMT 1M00 5% 1/10W 0805 1 ANY MANUFACTURER
R23
330746 CON PCMT 44PIN SOCKET PLCC 1 MACKENZIE- PLCC44P-T
U1
580642B PCB, CONTROLLER, PX712 1 AS PER DRILL DWG# 943308B WAS 580642A- ECN3007
BD ART FILE- 580642B.ZIP
Part number Description QTY MANUFACTURER COMMENTS
On solder side from pin 4
100111 RES 20R0 RN55D 1% MTL FLM AXIAL 1 DALE OR ANY MANUFACTURER (P1) to Ground plane.
R4 ECN3088
CAP LYTIC 47U 20% 16V SMT PAN. EEV-
200256 HB1C470 1 PANASONIC-EEV-HB1C470
C1
100584 RES SMD 1K 1% 1/10W 0805 WAS 120R (122-31120-00)-
1 ANY MANUFACTURER ECN3088
R2
700150 Replaces 205-70050-00-
DIODE, TVS, 600W, BI-DIR, 11.0V, SMT 2 On Semi- P6SMB11CAT3 ECN3151
ESD1 ESD2
220189 CAP EMI 10N 30% 50V RADIAL PAN. EXC-
CET103 2 PANASONIC-EXC-CET103
DF1 DF2
230109 CAP SMD .1UF 25V X7R CER 2 ANY MANUFACTURER
C2 C3
760279 IC MAX485ECSA DIG +15KV ESD RS485 WAS 760146 (LINEAR
XCVR 1 MAXIM- MAX485ECSA TECH-LTC485CS8)-
U1 ECN3298
323-00004-00 CONN, TERM BLK, PLG, PCRA, 4 PIN 1 WIELAND-25.332.3453.1
P1
CONN HEADER 14PIN PCMT TSW-107-08-T-D-
320-50107-00 RA .1SP D/R R/A 1 SAMTEC-TSW-107-08-T-D-RA
P2
612-18190-00 BRACKET, PC MNT SCREW TERM, 8190 (NO KEYSTONE- 8190
SCREW) 2
MT1 MT2
AS PER DWG# 943323B- DRILL
580647A PCB RS485 MA361 1 CHART WAS 580647- ECN3007
BD FILENAME- 580647A.ZIP
MA361 VOLUME CONTROL BD ASS'Y
Part Number Description QTY Manufacturer COMMENTS
100546 RES SMT 330K 5% 1/10W 0805 2 ANY MANUFACTURER
R24 R7
100561 RES SMT 1M00 1% 1/10W 0805 1 ANY MANUFACTURER
R8
100762 RES SMT 47K0 5% 1/10W 0805 2 ANY MANUFACTURER
R14 R18
100764 RES SMT 10K0 5% 1/10W 0805 1 ANY MANUFACTURER
R27
100765 RES SMT 1K00 5% 1/10W 0805 4 ANY MANUFACTURER R28 ADDED- ECN3023
R1 R2 R26 R28
100773 RES SMT 10R0 5% 1/10W 0805 3 ANY MANUFACTURER
R3 R4 R5
100774 RES SMT 330R 5% 1/10W 0805 2 ANY MANUFACTURER
R25 R6
100783 RES SMT 3K32 1% 1/10W 0805 2 ANY MANUFACTURER
R15 R16
100789 RES SMT 100K 1% 1/10W 0805 2 ANY MANUFACTURER
R13 R17
CAP LYTIC 47U 20% 16V SMT PAN. EEV-
200256 HB1C470 8 PANASONIC
C11 C16 C17 C2 C29 C32 C35 C5
230109 CAP CER_X7R 100N 10% 25V SMT 0805 17
C1 C10 C13 C14 C15 C18 C24 C3 C30 C33 ANY MANUFACTURER
C34 C36 C4 C6 C7 C8 C9
230146 CAP CER_NPO 15N 5% 50V SMT 0805 2 ANY MANUFACTURER NOT NPO
C22 C26
was 780158 (LM358ADR)-
780214 IC TL072CD DUAL OP AMP SOIC 1 Texas Instrument- TL072CD ECN3023
U3 Motorola- TL072CD
XISTOR MMBD3904LT1 NPN UNSORT SMD
720138 2N3904 1 ANY MANUFACTURER
Q1
121-31150-00 RES, SMT, 1.50K, 1%, TF, 1/8W, 0805 2 ANY MANUFACTURER
R10 R21
121-30681-00 RES, SMT, 681, 1%, TF, 1/8W, 0805 2 ANY MANUFACTURER
R12 R22
E01503 CAP CER 18P0 10% 50V SMT 0805 2 ANY MANUFACTURER
C12 C31
122-35100-00 RES, SMT, 1M, 5%, TF, 1/8W, 0805 1 ANY MANUFACTURER
R23
E01525 CAP CER_NPO 180N 10% 50V SMT 0805 1 ANY MANUFACTURER NOT NPO
C27
E01526 CAP CER_NPO 3N9 10% 50V SMT 0805 2 ANY MANUFACTURER NOT NPO
C19 C28
E01527 CAP CER_NPO 68N 10% 50V SMT 0805 2 ANY MANUFACTURER NOT NPO
C23 C25
E01528 CAP CER_NPO 18N 10% 50V SMT 0805 1 ANY MANUFACTURER
C20
224-09184-00 IC TC9184AP ANA TONE CONTROL 1 TOSHIBA- TC9184AP
U2
224-33310-00 IC CS3310KS CONV STEREO VOL CTRL 1 CRYSTAL SEMI
U1
121-32147-00 RES, SMT, 14.7K, 1%, TF, 1/8W, 0805 2 ANY MANUFACTURER
R20 R9
121-33127-00 RES, SMT, 127K, 1%, TF, 1/8W, 0805 2 ANY MANUFACTURER
R11 R19
E01534 DIODE BZX84C5 ZENER 5.1V ZENER 2 ZETEX-DIODES INC
CR1 CR2 BZX84C5V1
CONN HEADER 14PIN PCMT TSW-107-08-T-D-
330708 RA .1SP D/R R/A 1 SAMTEC TSW-107-08-T-D-RA NO GOLD!
P1
580648A PCB, VOLUME-TONE PX712 1 DRILL CHART- 943326A
BD ART- 580648A.ZIP
MA361 PARTS LIST
ICE MODULE ASSEMBLY
80A-00070-00 ICE MODULE ASSEMBLY
420904 HDW SCR PAN HD PH 6-32 X .375
420815 HDW SCR PAN HD PH POSI M3 X .5 (2)
430432 MISC MECH MA361 ICE MODULE FOA
501778J-3 METAL MA361 LOWER ICE BRACKET
900274 OEM PART ICE250A-IC MODULE
900306 AUDIO INPUT BOARD ASSEMBLY
900332 RS485 BOARD ASSEMBLY
770538 V1.04 SOFTWARE
760170 UNPROGRAMMED MPU
600297 SHIPPING CARTON
600298 BOTTOM FOAM INSERT
600299 TOP FOAM INSERT
AA MA361 12 CHANNEL DIGITAL AMPLIFIER
Revision Level: 02 Engineering Status: AL Comment:
Drawing Number:
Start Stop
Line Rev Date Date Part Number Rev Description Quantity U/M
____ ____ _____ ____ ___________ ____ ___________ ________ ____
10 310011 WIR CORDSET 3COND SH AC 14AWG BLACK 1 EA
850005000000
BELDEN 17605B OR ALPHA 536F
MEGA 17605M- MUST NOT BE INPRINTED
WITH "MADE IN TAIWAN" ON PVC JACKET
20 323-05004-00 00 CONN, TERM BLK, PLG, RA, 4 PIN WIELAND 1 EA
WIELAND #25.320.3453.1
30 330233 CON PCMT 12 PIN .1SP SCREW TERM BLOCK 1 EA
MOLEX/BEAU- 860512
20PC /PK (MIN)
32 10/ 7/02 420940 HDW SCR SEMS PAN HD PH 6-32X.25 BLK OX 6 EA
SPEC: SEMS SCREW, (EXT LOCKWASHER TYPE)
6-32 THREAD X .25" LONG
MATERIAL ALLOY STEEL OR STAINLESS
FINISH: BLACK OXIDE OR BLACK PASSIVATE
ECN3319- 10/7/2002
40 480746 LBL MA361 RS485 LABEL 1 EA
AS PER DWG#- 480746
NO ADDITIONAL ARTWORK REQUIRED.
48 1/15/03 630706 LIT MAN AA WARRANTY REGISTRATION CARD 1 EA
AS PER- 630706 POSTSCRIPT AND
PDF FILES
REPLACES 500-00000-00
PER ECN3356- 1/15/2003
ECN3356- 1/15/2003
54 4/ 2/02 508-00000-02 00 LIT MAN AA SAFETY WARNING SHEET 1 EA
EITHER IN-HOUSE OR OUT OF HOUSE
PDF FILE- 508-00000-02.PDF
ECN3160- 4/2/2002
56 4/ 2/02 502-00070-00 LIT MAN AA MA361 QUICK START GUIDE 1 EA
AS PER PDF FILE- 502-00070-00