Text preview for : HarmanKardon-SUBTS10 actsub.pdf part of Harman/Kardon SUBTS10 active subwoofer
Back to : HarmanKardon-SUBTS10 acts | Home
harman/kardon
HKTS 10
Home Cinema Speaker System
SERVICE MANUAL
harman/kardon, Inc. 250 Crossways Park Dr. Woodbury, New York 11797 Rev0 8/2002
CONTENTS
SPECIFICATIONS . . . . . . . . . . . . . . . . . . . . . . . . . .. . . . . .. . . . . . . . . .. .. . .. . . . . .. .. . . . . . . . 1 DETAILED SPECIFICATIONS. . . . . . . . . . . . . . . . . . . . . .............. . . . . .. . . . . .. . . . . . . . . . . 2 CONTROLS & CONNECTIONS . . . . . . . . . . . . . .. . . . . . . . . . . . . . .. . . . . . . . . . .. . . . . . . . . . 3 OPERATION & ADJUSTMENTS. . . . . . . . . . . . . .. . . . . . . . . . . . . . . .. . . . . . . . . .. . . . . . . . . . 8 BASIC TROUBLESHOOTING GUIDE . . . . . . . . . . . . . . . . . . .. . . . . . . . . . . . . . ... . . . . . . . . . . 9 SUB-TS10 TEST PROCEDURE. . . . . . . . . . . . . .. . . . . . . . . . . . . . . .. . . . . . . . . .. . . . . . . . . . 10 SUB-TS10 BLOCK DIAGRAM . . . . . . . . . . . . . . . . . . . . .. . . . . . . . . . . . . . . . .. . .. .. . . . . . . . 11 MECHANICAL/PACKING PARTS LIST ....... . . . . .. . . . . . . . .. .. . . . .. .. . . . . . . . . .. . .. . . . . . . 12 SUB-TS10 EXPLODED VIEW. . . . . . . . . . . . . . . . . . . . .. . . . . . . . .. . . . .. . . . .. . .. .. . . . . . ... . 13 SUB-TS10 PCB DRAWINGS. .. . . . . . . . . . . . . . . ... . . . .. . . . . . . ... . . . . . . . . .. . .. .. . . . . . . . 14 SUB-TS10 IC TRANSISTOR PINOUTS . ... . . . .. . . . . . . . ............ . . . . . . . .. . .. .. . . . . . . . 16 SUB-TS10 ELECTRICAL PARTS LIST ............. ... . . . . . . . . . .. . . .. . . . . . . . . . . .. . .. . . . . . . 17 SUB-TS10 SCHEMATIC DIAGRAMS . . . . . . . . . . . . . . . . . . . . .. . .. .. .. . . . .. . .. . . . . . . . . . . . .20
SPECIFICATIONS
HKTS 10 System Frequency Response 35Hz 20kHz (6dB) SAT-TS10 Satellites
Recommended Power 10 110 watts Impedance 8 ohms nominal Sensitivity 86dB @ 1 watt/1 meter Tweeter One 1" dome, videoshielded Midrange One 4" driver, videoshielded Dimensions (H x W x D) 10-1/8" x 5-1/4" x 5-3/8" 257mm x 133mm x 137mm Weight 6.6 lb/3.0kg
CEN-TS10 Center
Recommended Power 10 110 watts Impedance 8 ohms nominal Sensitivity 86dB @ 1 watt/1 meter Tweeter One 1" dome, video-shielded Midrange Dual 4" drivers, videoshielded Dimensions (H x W x D) 5-1/16" x 16-1/2" x 5-3/16" 128mm x 418mm x 131mm Weight 10 lb/4.5kg
SUB-TS10 Subwoofer
Amplifier 150 watts RMS Bass Driver 12" woofer, bass-reflex enclosure Dimensions (H x W x D) 20-5/16" x 16-3/8" x 15-1/16" 515mm x 416mm x 382mm Weight 40 lb/18.0kg
Occasional refinements may be made to existing products without notice but will always meet or exceed original specifications unless otherwise stated.
1
HKTS 10
SUB-TS10
LINE VOLTAGE US 120vac/60Hz
harman/kardon
150W Powered Amplifier
Yes/No Yes Hi/Lo Line 108-132 Unit Vrms Notes Normal Operation
Parameter Amp Section Type (Class AB, D, other) Load Impedance (speaker) Rated Output Power THD@ Rated Power THD @ 1 Watt DC Offset Damping factor Input Sensitivity Input Frequency Line Input (L&R) LFE Input Speaker/Hi Level Input Signal to Noise SNR-A-Weighted SNR-unweighted SNR @ 1W-unweighted Residual Noise Floor Residual Noise Floor Input Impedance Line input L&R , LFE Speaker/Hi Level Input Filters Left & Right Low Pass fixed LFE Low Pass fixed Subsonic filter (HPF) Limiter Features LFE Input Volume pot Taper (lin/log) ATO Signal Sensing (ATO) ATO test Frequency ATO Line Level ATO Speaker level input ATO Turn-on time Auto Mute/ Turn-OFF Time Power on Delay time Transients/Pops ATO Transient Turn-on Transient Turn-off Transient Efficiency
Specification D 4 150 0.08 0.15 5
Unit D Ohms Watts % % mV-DC
QA Test Limits Conditions n/a n/a 150 1 0.5 30 30 NA ±2dB ±2dB ±2dB 85 80 60 3.0 2.0 n/a n/a ±2dB ±2dB ±2dB n/a functional functional functional Nominal Freq. To Rated Power To Rated Power To Rated Power rel. to rated power rel. to rated power rel. to 1W Output Volume @max, using RMS reading DMM/VOM (or A/P) Volume @max, w/ A/P Swept Bandpass Measurement (Line freq.+ harmonics) Nominal Nominal @ -3dB ref. 100Hz @ -3dB ref. 100Hz @ -3dB ref. 100Hz
Notes
Nominal 1 input driven 22k filter 22k filter @ Speaker Outputs Measured at speaker terminals, Output power 140 Watts THD 0.1 % 1 input driven 1 input driven LFE input driven only (-20 dB below Line In)...1 input driven A-Weighting filter 22k filter 22k filter
>100 DF 50 220 220 2.2 Hz mVrms mVrms Vrms
100 dBA 90 dBr 65 dBr 1.2 mVrms 0.8
mVrms(max)
10 K ohms 4.7 K ohms 130 Hz 220 Hz 22 Hz YES YES log YES -----
BW Limited to 220 Hz
--
50 Hz 4.0 mV 40 mV 5 ms 15 minutes 3 sec. 5 mV-peak 50 mV-peak 50 mV-peak
n/a 2.0 - 8.0 20 - 80 functional 10 - 25 functional 10 100 100 2mV@50Hz into Line Input w/ 1 ch. driven 50mV@50Hz into Line Input w/ 1 ch. driven Amp connected and AC on, then input signal applied T before muting, after signal is removed AC Power Applied @ Speaker Outputs @ Speaker Outputs @ Speaker Outputs
AC Line cycled from OFF to ON AC Line cycled from ON to OFF Maximum allowable input power under nominal Input voltage and frequency, HOT or COLD operation. 150 Watts @ 4 Ohms nominal line voltage
Stand-by Input Power Power Cons.@rated power Protection Short Circuit Protection Thermal Protection DC Offset Protection Line Fuse Rating US Version
10 Watts 230 Watts YES 65 deg. C YES ----
12 250 functional functional functional
@ nom. line voltage @ nom. line voltage Direct short at output @1/8 max unclipped Power DC present at Speaker Out leads Type-T or Slo Blo
Temperature rise should not exceed 35K rise Relay or crowbar (for driver/fire protection) External fuse with UL/SEMKO rated holder
3.15 Amps
2
HKTS 10
harman/kardon
SUB-TS10 SUBWOOFER AMPLIFIER PANEL CONTROLS AND CONNECTIONS
¢ £ TM
R L
LINE LEVEL IN
SUB
¶ ª § ·
FILTER
OFF ON
FILTER REMOTE CONTROL
SUBWOOFER LEVEL
L GREEN: ON
PHASE
RED: STAND-BY
¡
IMPORTANT: CONNECT STRIPED WIRE TO RED (
R NORMAL REVERSE ON AUTO
,
) SPEAKER TERMINAL.
SUB-TS10
For use with HKTS 10 System
harman/kardon
POWER
Made in China
/
AC 120V~60Hz
CAUTION
RISK OF ELECTRIC SHOCK DO NOT OPEN
¤
¡ Speaker-Level Inputs TM Speaker-Level Outputs £ Line-Level Subwoofer (SUB) Input ¢ Line-Level Full-Range Inputs Phase Switch § High-Cut (Low-Pass) Filter Switch ¶ Music-Sense On/Off Switch · Filter Remote Control Input ª LED Indicator , Subwoofer-Level Control / Master Power Switch ¤ AC Power Cord
¡ Speaker-Level Inputs: Connect these binding post terminals to the main left and right speaker terminals of your receiver or amplifier, if your receiver or amplifier does not have a line-level subwoofer output. Remember to maintain polarity by connecting the (+) terminal on the receiver/amplifier to the (+) terminal on the SUB-TS10 subwoofer, and the () terminal on the receiver/amplifier to the () terminal on the SUB-TS10 subwoofer. TM Speaker-Level Outputs: If you are using the Speaker-Level Inputs ¡ on the SUB-TS10, you should connect these binding post terminals to your front left and right speakers, remembering to maintain polarity by connecting the (+) terminal on
the SUB-TS10 subwoofer to the (+) terminal on the speaker, and the () terminal on the SUB-TS10 subwoofer to the () terminal on the speaker. If you are not using the Speaker-Level Inputs ¡, then connect your front left and right speakers directly to your receiver or amplifier. See pages 6 and 7 for further information. £ Line-Level Subwoofer (SUB) Input: Connect the subwoofer output of a receiver with digital surround sound decoding, such as Dolby* Digital or DTS® to this input. This , input bypasses the SUB-TS10's internal crossover circuitry, and should only be used with a filtered signal. If your receiver does not have digital decoding, you should use the
Line-Level Full-Range Inputs ¢ instead. ¢ Line-Level Full-Range Inputs: Connect the line-level subwoofer output or preamp output(s) of your receiver or amplifier to these inputs. If your receiver does not have a separate subwoofer output, use a Y-adaptor (not supplied) to bridge the receiver's preamp output to the main amp input for that channel, and connect the long end of the adaptor to the corresponding line-level input on the SUB-TS10. If your receiver has only a single subwoofer output, you may connect it to either the left or right line-level input on the SUB-TS10, and no Y-adaptor is needed. Phase Switch: This switch determines whether the SUB-TS10 subwoofer's piston-
3
HKTS 10
harman/kardon
SUB-TS10 SUBWOOFER AMPLIFIER PANEL CONTROLS AND CONNECTIONS
like action moves in and out in phase with the main speakers. If the speakers were to play out of phase, the sound waves produced by the subwoofer would be cancelled out, reducing bass response. This phenomenon depends in part on the relative placement of the speakers in the room. In most cases, the Phase Switch should be left in the NORMAL position. However, it does no harm to experiment with the Phase Switch , and you may leave it in the position that maximizes bass response. § High-Cut (Low-Pass) Filter Switch: Placing this switch in the ON position activates circuitry that cuts out all audio input signals above 120Hz. This allows the SUBTS10 to focus its power on reproducing the low-frequency portion of the signal, avoiding inefficiency and distortion. Engage this filter when using the Speaker-Level Inputs ¡, or when using the Line-Level Full-Range Inputs ¢, unless your receiver or processor processes its line-level output using a low-pass filter. The filter has no effect when the SUB Input £ is used. ¶ Music-Sense On/Off Switch: When placed in the AUTO position, and when the Master Power Switch / is turned on, the SUB-TS10 will automatically turn itself on or place itself in the Standby mode, depending on whether it is receiving an audio signal. When this switch is placed in the ON position, the SUB-TS10 will remain on, whether or not it is receiving an audio signal. · Filter Remote Control Input: This input accepts a remote control signal from a compatible Harman Kardon A/V receiver that enables you to override the High-Cut (Low-Pass) Filter Switch §, by signaling the SUB-TS10 to engage the filter even when the switch is in the OFF position. ª LED Indicator: This LED indicates whether the SUB-TS10 is in the ON or STANDBY state when used with the Music-Sense On/Off Switch ¶ in the AUTO position. The LED is lit Green to indicate that the SUB-TS10 is receiving an audio signal and is turned on, and the LED is lit Red to indicate that no signal is being received and the SUB-TS10 is in Standby mode. When the Music-Sense On/Off Switch ¶ is in the ON position, the LED will be lit Green, whether or not an audio signal is present. When the Master Power Switch / is turned off, the LED goes dark, no matter which position the Music-Sense On/Off Switch ¶ is in. , Subwoofer-Level Control: Volume can be adjusted using the SubwooferLevel Control. Turn the control clockwise to increase the SUB-TS10's volume, or counterclockwise to decrease it. / Master Power Switch: Place this switch in the "·" position to power-on the SUB-TS10 subwoofer. The SUB-TS10 will then be either in the Standby mode or completely on, depending on the position of the Music-Sense On/Off Switch ¶. ¤ AC Power Cord: Make sure to plug this cord into an active, unswitched electrical outlet for proper operation of the SUBTS10. The cord should not be plugged into the accessory outlets found on some audio components.
4
HKTS 10
SPEAKER CONNECTIONS (continued)
Dolby Digital or DTS (or other Digital Surround Mode) Connection
USE THIS INSTALLATION METHOD FOR DOLBY DIGITAL, DTS OR OTHER DIGITAL SURROUND PROCESSORS: Use the line-level input jack marked SUB £ for the Low-Frequency Effects channel. Connect this jack to the subwoofer output or LFE output on your receiver or amplifier. Connect each speaker to the corresponding speaker terminals on your receiver or amplifier. Make sure that you have configured your surround sound processor for "Subwoofer On. The front left, front right, center and " rear surround speakers should all be set to "Small. " When all connections have been made, plug the AC power cord on the subwoofer into an AC outlet.
LINE LEVEL IN
harman/kardon
Front Left +
Center +
Front Right +
SUB
R L
Front Left SUB/LFE Out Surround Left Center
Front Right
Surround Right
Surround Left +
Receiver
Surround Right +
5
HKTS 10
SPEAKER CONNECTIONS (continued)
Dolby Pro Logic (Non-Digital) Line Level
USE THIS INSTALLATION METHOD FOR DOLBY PRO LOGIC APPLICATIONS (NOT DOLBY DIGITAL, DTS OR OTHER DIGITAL PROCESSING), WHERE THE RECEIVER/ PROCESSOR IS EQUIPPED WITH A SUBWOOFER OUTPUT, OR A VOLUMECONTROLLED PREAMP (LINE-) LEVEL OUTPUT: Use the supplied RCA-type patch cord to connect the line-level subwoofer output on your receiver or amplifier to either the left or right Line-Level Full-Range Input ¢ on the SUB-TS10 subwoofer. Use both the left and right inputs on the subwoofer if your receiver or processor has both left and right line-level outputs. If your receiver is equipped with line-level outputs but does not have a separate subwoofer output, use a Y-adaptor (not supplied) to bridge the receiver's preamp output to the main amp input for that channel, and connect the long end of the adaptor to the corresponding line-level input on the SUB-TS10. IMPORTANT: Do not use the SUB Input £ on the subwoofer with Dolby Pro Logic processors. Make sure that you have configured your surround sound processor for "Subwoofer On. The front left, front right, " center and rear surround speakers should all be set to "Small. " When all connections have been made, plug the AC power cord on the subwoofer into an AC outlet. Connect each speaker to the corresponding speaker terminals on your receiver or amplifier.
harman/kardon
Front Left +
Center +
Front Right +
SUB-TS10 Subwoofer Line-Level L R
Front Left SUB/LFE Out Surround Left Center
Front Right
Surround Right
Surround Left +
Receiver
Surround Right +
6
HKTS 10
SPEAKER CONNECTIONS (continued)
Dolby Pro Logic* (Non-Digital) Speaker Level
USE THIS INSTALLATION METHOD FOR DOLBY PRO LOGIC APPLICATIONS (NOT DOLBY DIGITAL, DTS OR OTHER DIGITAL PROCESSING), WHERE THE RECEIVER/ PROCESSOR DOES NOT HAVE A SUBWOOFER OUTPUT, OR A VOLUMECONTROLLED PREAMP (LINE-) LEVEL OUTPUT: Connect your receiver or amplifier's front left and right speaker terminals to the left and right Speaker-Level Input ¡ terminals on the SUB-TS10 subwoofer that are marked "High Level In." Connect the left and right Speaker-Level Output TM terminals on the SUB-TS10 subwoofer that are marked "High Level Out" to the corresponding terminals on the back of your front left and right speakers. Connect your receiver or amplifier's center, and surround left and right speaker terminals to the corresponding terminals on the back of your center, and surround left and right speakers. When all connections have been made, plug the AC power cord on the subwoofer into an AC outlet.
Center
harman/kardon
Front Left
+
+
Front Right
+
SUB-TS10 Subwoofer
R L
Receiver
Front Left Center Front Right
Surround Left
Surround Right
Surround Left
+
Surround Right
+
7
HKTS 10
OPERATION
Move the Master Power Switch / (marked Power) to the "·" (On) position. The SUB-TS10 subwoofer will automatically turn itself on or go into Standby mode, depending on whether or not a signal is being sent to it by your receiver or surround processor, and provided that the MusicSense On/Off Switch ¶ is moved to the right so that it is in the AUTO position. When your receiver or amplifier is off, or is not sending program material to the subwoofer, the subwoofer will be in Standby mode and the LED Indicator ª on the amp panel will turn red. When the subwoofer senses an audio signal, it will automatically turn itself on and the LED Indicator ª will turn green. If the subwoofer does not sense a signal after approximately twenty minutes, it will automatically go into Standby mode.
harman/kardon
When the Music-Sense On/Off Switch ¶ is switched to the ON position, the subwoofer will remain on, whether or not program material is playing. If you will be away from home for an extended period of time, or if the subwoofer will not be used, switch the Master Power Switch / to the OFF position.
Volume
Volume can be adjusted using the Subwoofer-Level Control ,, as shown below.
Subwoofer Level
Subwoofer Level
MIN
MAX
MIN
MAX
Additional Bass Adjustments
In addition to the volume adjustments described above, the SUB-TS10 subwoofer includes a Phase Switch and a Filter Switch § that can be used to adjust the bass response to suit your listening environment or taste. In most situations, the Phase Switch should be left in the NORMAL position. If you suspect that the subwoofer is playing out of phase with the other speakers, which would tend to diminish bass response, try placing this switch in the REVERSE position. There is no harm in experimenting, and you may return the switch to the NORMAL position at any time. If you rearrange your room and reposition the speakers, it would be a good idea to check whether they are in phase by flipping this switch. The High-Cut (Low-Pass) Filter Switch § limits the frequencies of the audio signal inputted to the subwoofer to the low frequencies that the subwoofer reproduces best. This allows the subwoofer to perform more efficiently, and with superior bass reproduction, minimizing distortion that might occur if the subwoofer attempted to reproduce higher frequencies. This switch should be left in the ON position, except: 1. When the SUB Input £ is being used, in which case it has no effect, or 2. When the Speaker-Level Inputs TM or the Line-Level Full-Range Inputs ¢ are being used with a crossover or filter on board the receiver or processor. In these two circumstances, place the switch in the OFF position.
8
HKTS 10
TROUBLESHOOTING
If there is no sound from any of the speakers: · Check that receiver/amplifier is on and a source is playing. · Check that the powered subwoofer is plugged in and its Master Power Switch / is switched on to the "·" position. · Check all wires and connections between receiver/amplifier and speakers. Make sure all wires are connected. Make sure none of the speaker wires are frayed, cut or punctured. · Review proper operation of your receiver/amplifier. If there is no sound coming from one speaker: · Check the "Balance" control on your receiver/amplifier. · Check all wires and connections between receiver/amplifier and speakers. Make sure all wires are connected. Make sure none of the speaker wires are frayed, cut or punctured, and that no wires are touching each other. · In Dolby Digital or DTS mode, make sure that the receiver/processor is configured so that the speaker in question is enabled. · Turn off all electronics and switch the speaker in question with one of the other speakers that is working correctly. Turn everything back on, and determine whether the problem is in the same place: i.e., the speaker that was working previously now has no sound and the speaker that was not working now sounds fine; or whether it has moved: i.e., the speaker that was not working still has no sound and the speaker that was working is still fine. If the problem is in the same place, the source of the problem is most likely with your receiver or amplifier, and you should consult the owner's manual for that product for further information. If the problem has followed the speaker, consult your dealer for further assistance or, if that is not possible, visit our Web site at www.harmankardon.com for further information. If there is no sound from the center speaker: · Check all wires and connections between receiver/amplifier and speaker. Make sure all wires are connected. Make sure none of the speaker wires are frayed, cut or punctured. · If your receiver/processor is set in Dolby Pro Logic mode, make sure the center speaker is not in phantom mode. · If your receiver/processor is set in Dolby Digital or DTS mode, make sure the receiver/processor is configured so that the center speaker is enabled. If the system plays at low volumes but shuts off as volume is increased: · Check all wires and connections between receiver/amplifier and speakers. Make sure all wires are connected. Make sure none of the speaker wires are frayed, cut or punctured. · If more than one pair of main speakers is being used, check the minimum impedance requirements of your receiver/amplifier. If there is low (or no) bass output: · Make sure the SUB or line-level inputs of the SUB-TS10 subwoofer and SUB or LFE output of your receiver or amplifier are properly connected by the RCA-type patch cord. · If you are using the SUB-TS10's speakerlevel inputs, check your speaker cables to make sure they are all connected; that none of the wires are frayed, cut or punctured; and that you have maintained the correct polarity by connecting positive terminals to positive terminals, and negative terminals to negative terminals. · Make sure the subwoofer is plugged into an active electrical outlet and its Master Power Switch / is switched on to the "·" position. · Check the speaker setup (bass management) settings in your AVR receiver or processor to make certain that the front, center and surround speakers are configured for "Small," and that the subwoofer is set for "Yes" or "On."
harman/kardon
If there is no sound from the surround speakers: · Check all wires and connections between receiver/amplifier and speakers. Make sure all wires are connected. Make sure none of the speaker wires are frayed, cut or punctured. · Review proper operation of your receiver/processor and its surround sound features. · Make sure the movie or TV show you are watching is recorded in a surround sound mode. If it is not, check to see whether your receiver/processor has other surround modes you may use. · In Dolby Digital or DTS mode, make sure your receiver/processor is configured so that the surround speakers are enabled. · Review the operation of your DVD player and the jacket of your DVD to make sure that the DVD features the desired Dolby Digital or DTS mode, and that you have properly selected that mode using both the DVD player's menu and the DVD disc's menu.
9
HKTS 10
Test Set Up and Procedure
SIGNAL GENERATOR AC VOLT METER (10V)
HKTS10
UNDER TEST
R
L
LINE LEVEL IN
SUB
FILTER
OFF ON
FILTER REMOTE CONTROL
SUBWOOFER LEVEL
L GREEN: ON
PHASE
R NORMAL REVERSE
RED: STAND-BY
ON
AUTO
IMPORTANT: CONNECT STRIPED WIRE TO RED (
) SPEAKER TERMINAL.
AMPLIFIER
SUB-TS10
For use with HKTS 10 System
harman/kardon
POWER
Made in China
{
Equipment needed:
· · · · Function/signal generator/sweep generator Integrated Amplifier Multimeter Speaker cables
AC 120V~60Hz
CAUTION
RISK OF ELECTRIC SHOCK DO NOT OPEN
General Unit Function (UUT = Unit Under Test)
1) 2) 3) 4) 5) 6) 7) From the signal generator, connect one line level (RCA) cable to the single Sub input on the UUT. On the front of the unit, turn the LEVEL control full counterclockwise. FILTER control should be OFF. Turn on generator, adjust to 75mV, 50 Hz. Plug in UUT; turn the power switch ON. LED should be Red. Turn LEVEL control full clockwise (MAX) LED should now be Green; immediate bass response should be heard and felt from port tube opening. Turn off generator, turn VOLUME control fully counterclockwise, disconnect RCA cable. Connect one pair of speaker cables to Speaker Level input terminal (IN) on Right channel only. Cables should be connected to an integrated amplifier fed by the signal generator. 8) Turn on generator and adjust so that speaker level input at the amplifier is 1.6V, 50 Hz. Turn LEVEL control full clockwise. 9) Green LED should light, immediate bass response should be heard and felt from the port tube opening.
Sweep Function
1) Follow steps 7-9 above, using a sweep generator as a signal source. 2) Sweep generator from 20Hz to 300Hz. Listen to the cabinet and drivers for any rattles, clicks, buzzes or any other noises. If any unusual noises are heard, remove woofers and test.
Driver Function
1) Remove woofer from cabinet; detach + and - wire clips. 2) Check DC resistance of woofer; it should be 3.5 ohms ±10% 3) Connect a pair of speaker cables to driver terminals. Cables should be connected to an integrated amplifier fed by a signal generator. Turn on generator and adjust so that speaker level output is 5.0V. 4) Sweep generator from 20Hz to 1kHz. Listen to driver for any rubbing, buzzing, or other unusual noises.
10
HKTS 10
harman/kardon
11
HKTS 10
HKTS 10 Subwoofer/Satellite/Center
Part Number Description
harman/kardon
Mechanical/Packing Parts List
Subwoofer SUB TS10 30PF14FM-DW02 xc125006-b xc125007 wi5334-1 06-T5305004 Satellites SAT-TS10 10PR70BZK-HW02 35DM13NG-PT02 XR5176-1 xc045016-b xc045017-1 xd045016-b Center Channel CEN-TS10 10PR70BZK-MW02 35DM13NG-HT02 xr5177-1 xc045014-b xd045014-b xc045015-1 Packing/Accessories wg5320 ai5170 at5108 sal5009 sal063-1 sal5020 sal5044 wi5688 wi5689 wi5691 Master carton Owner's manual Warranty card Wire set 40' (surround) Wire set 20' (center) Wire set 15' (front satellites) 15' RCA cable Center Channel Bracket/Support Foot Wall Bracket for Satellite Woofer 4" 13mm tweeter Crossover Network Baffle Enclosure Grille 4" woofer 13 mm tweeter Crossover Network Baffle Grille Enclosure 12" Woofer (DCR = 3.5 ohms +/-10%) Front Baffle Grille Foot (4) Screw for front baffle & Feet (8)
12
HKTS 10
harman/kardon
13
HKTS 10
harman/kardon
14
HKTS 10
harman/kardon
15
HKTS 10
harman/kardon
Integrated Circuit Diagrams
4558 DUAL OP AMP, U203
OPAMP, QUAD 14P DIL TL074 U201, 202, 301
TIP31C NPN, TIP32C PNP, Q501, 502
TRANS, PNP, 2N5401 TAP, TO-92, Q503
TRANS, NPN, 2N5551 TAP, Q114,115
B C E
TRANS, PNP, TAP, 2SA1015GR Q101,107,112
TRANS, NPN, 2SC1815GR TAP, 2SC2235 Q108,109,111,113, Q201-204,206-208,301,302
16
00340-1
HKTS 10 SUBTS-10 Electrical Parts List
Input/Power Amp PCB Part # Resistors
11014103j26 11014222j26 11014432j26 11014472j26 11016102j26 11016103j26 Resistor 10K 1/4W ±5% CF Resistor 2.2K 1/4W ±5% CF Resistor 4.3K 1/4W ±5% CF Resistor 4.7K 1/4W ±5% CF Resistor 1K 1/6W ±5% CF Resistor 10K 1/6W ±5% CF 3 1 1 1 5 36
harman/kardon
Description
QTY
Reference Designator
11016104j26 11016105j26 11016122j26 11016124j26 11016151j26 11016153j26 11016154j26 11016182j26 11016183j26 11016203j26 11016205j26 11016221j26 11016222j26 11016223j26 11016224j26 11016273j26 11016333j26 11016393j26 11016472j26 11016473j26 11016474j26 11016512j26 11016513j26 11016562j26 11016621j26 11016751j26 11016755j26 11016822j26 11016913j26 116161002f26 116161102f26 116162200f26 116162202f26 11012472j00 11020332jk3 11120102jk3 11130471jk2 11350s68j00 115h503a102 Capacitors 129a154j633 1302b101k503 1302b221k503 1302b470k503
Resistor 100K 1/6W ±5% CF Resistor 1M 1/6W ±5% CF Resistor 1.2K 1/6W ±5%CF Resistor 120K 1/6W ±5% CF Resistor 150 ohms 1/6W ±5% CF Resistor 15K 1/6W ±5% CF Resistor 150K 1/6W ±5% CF Resistor 1.8K 1/6W ±5% CF Resistor 18K 1/6W ±5% CF Resistor 20K 1/6W ±5% CF Resistor 2.0M 1/6W ±5% CF Resistor 220 ohms 1/6W ±5% CF Resistor 2.2K 1/6W ±5% CF Resistor 22K 1/6W ±5% CF Resistor 220K 1/6W ±5% CF Resistor 27K 1/6W ±5% CF Resistor 33K 1/6W ±5% CF Resistor 39K 1/6W ±5% CF Resistor 4.7K 1/6W ±5% CF Resistor 47K 1/6W ±5% CF Resistor 470K 1/6W ±5% CF Resistor 5.1K 1/6W ±5% CF Resistor 51K 1/6W ±5% CF Resistor 5.6K 1/6W ±5% CF Resistor 620 ohms 1/6W ±5% CF Resistor 750 ohms 1/6W ±5% CF Resistor 7.5M 1/6W ±5% CF Resistor 8.2K 1/6W ±5% CF Resistor 91K 1/6W ±5% CF Resistor 10K 1/6W ±1% MF Resistor 11.0K 1/6W ±1% MF Resistor 220 ohms 1/6W ±1% MF Resistor 22.0K 1/6W ±1% MF Resistor 4.7K 1/2W ±5% Resistor 3.3K 2W ±5% Metal Film Resistor 1K 2W ±5% Metal Film Resistor 470 ohms 3W ±5% Cement Resistor 0.068 ohms 5W Variable Resistor 50K
6 1 1 1 1 1 1 2 1 1 1 1 1 5 2 2 1 1 3 7 2 2 1 1 1 1 1 1 4 2 1 1 1 2 1 1 2 1 1
R503,504,510 R511 R506 R505 R153,213,214,215,254 R128,130,149,150,209,212,216,217,218,220,221, 222,225~229,230,232,234,235,240,248,260, 273~277,279,305,306,308,311,314,319 R122,126,231,263,266,307 R259 R265 R233 R253 R107 R252 R145,271 R262 R309 R257 R144 R102 R238,247,255,256,316 R272,278 R223,237 R310 R151 R200,207,258 R106,129,219,249,250,251,264 R127,312 R210,211 R224 R152 R160 R315 R313 R270 R203-206 R301,303 R302 R317 R318 R201,202 R134 R148 R501,502 R147 VR201 Level Pot
Metallize Cap. 0.15U 63V ±5% MSC Metallize Cap. 100P 50V ±10% Disc Capacitor 220P 50V ±10% Disc Capacitor 47P 50V ±10%
2 3 12 1
C221,222 C302,303,306 C200,204,205,207,208,210,211,212,214,220,230, 237 C229
17
HKTS 10
Part #
1302f104z503 132103j503 132103ja03 132104ja03 132183j503 132223ja03 132273ja03 132473ja03 1353105m50 1353106m50 1353107m10 1353107m16 1353107m35 1353225m50 1353216 1353250 1353227m16 1353476m16 132103kb00 1385478m63 1385478m63 Semiconductors 192027c1815gr 192027c2235y 192028a1015gr 1921672n5551 1921682n5401 197131n4148 19915000335 19915000625 19915001605 192161tip31c 192162tip32c 19510204hgw 19700kbu606g 197101n4004 19006m4558d 19016tl074cn Miscellaneous 1091ttc802j0 1201000003 171urwh124d 1740rca326p 1741jy35421 17420810360g 180tms7210v 150r4055900a 152u602015 154k31505t0 15563032i 180pbr12c11s Thermister TTC-802(JS) NTC Inductor 10W Relay RWH-SH-124D (1600 ohm) JACK RCA-326 PURPLE/WHT/RED PHONE JACK 3.5mm JY-3542-01-030 SPK JK.BP 8PIN SH0810360G SWITCH SLIDE 6PIN MS7210V Power Transformer I/P:120V/60Hz Line Cord SVT FT-2 6FT Fuse 3.15A 250V 30mm UL/CSA Fuse Holder HTB-32I 30mm UL/CSA PUSH SW BR12C11S 1 2 1 1 1 1 3 1 1 1 1 1 TH1 FB1,2 RL1 JK201 (Set of three) JK203 JK202 (Set of eight) Filter/Phase/Auto-on-off T501 F501 F501 SW501 POWER Transistor 2SC1815GR Transistor 2SC2235Y Transistor 2SA1015GR Transistor 2N5551 Transistor 2N5401 1N4148 Zener Diode 3.3V 1/2W 52mm Zener Diode 6.2V 1/2W 52mm Zener Diode 16V 1/2W 52mm Transistor TIP31C SGS Transistor TIP32C SGS LED 204HGW Indicator Diode 6A 800V KBU606G 1N4004 I.C. OPA 4558D Dual Op-amp I.C. TL074CN ST Quad Op-amp 12 1 3 2 1 18 1 1 1 1 1 1 1 2 1 3
harman/kardon
Description
Disc Capacitor 0.1U 50V +80/-20% Mylar Capacitor 0.01U 50V ±5% Mylar Capacitor 0.01U 100V ±5% Mylar Capacitor 0.1UF 100V ±5% Mylar Capacitor 0.018U 50V ±5% Mylar Capacitor 0.022uF 100V ±5% Mylar Capacitor 0.027U 100V ±5% Mylar Capacitor 0.047uF 100V ±5% Electrolytic Cap. 1U 50V ±20% Electrolytic Cap. 10U 50V ±20% Electrolytic Cap. 100U 10V ±20% Electrolytic Cap. 100uF 16V ±20% Electrolytic Cap. 100U 35V ±20% Electrolytic Cap. 2.2U 50V ±20% Electrolytic Cap. 22U 16V ±20% Electrolytic Cap. 22U 50V ±20% Electrolytic Cap. 220U 16V ±20% Electrolytic Cap. 47U 16V ±20% Mylar Cap. 0.01U 200V ±10% Electrolytic Cap.4700U 63V ±20% Electrolytic Cap.4700U 63V ±20%
QTY
14 2 2 4 2 1 1 2 1 12 2 1 2 1 1 3 2 1 1 1 1
Reference Designator
C107,117,122,144,232,242,244,245,246,252,254, 256,320,322 C305,317 C103,104 C123,218,503,504 C223,224 C215 C143 C216,217 C228 C201,202,206,213,219,231,241,243,251,253,319, 321 C114,115 C234 C507,508 C509 C304 C225,505,506 C118,233 C318 C500 C501 C502
Q108,109,113,201-204,206,207,208,301,302 Q111 Q101,107,112 Q114,115 Q503 D102,103,104,105,143,201,202~208,214,215, 216,310,312 D213 D101 D502 Q501 Q502 D209 D501 D110,504 U203 U201,202,301
18
HKTS 10
Power Amp Module PW150D
Part# Resistors 11812061001j 11812061002j 118120610r0j 11812061201j 11812062002j 11812062201j 11812062701j 11812063000j 11812063301j 11812063902j 11812064700j 11812064701j 11812064702j 11812064704j 118120647r0j Capacitors 141c0101k50 141c0220k50 141c0561k50 141c6104m50 141c7223k50 141d7104ka0 128e106ma01 141d7104kb0 Semiconductors 19016tl072dts 19209124126qs 19209139066rs 19209210376qs 19209215146rs 19703rls4148s 19915000563s 19915001203s 19915001503s 192232irf9640 192233irf640 Miscellaneous 1759f40hr2 12214121m4191 12214350j4180 06-t3085020 06-t31207 IC1 Q1,4,5 Q2,8 Q7,9 Q3,6 D1,2,3,4,5,6 Z1,2 Z5,6 Z3,4 Q10 Q11 SMD I.C. TL072CDT SGS Dual Op-Amp TRANS, NPN 50V 0.15A 2SC2412K TRANS, NPN 120V 0.05A 2SC3906K TRANS, PNP 50V 0.15A 2SA1037K TRANS, PNP 120V 0.05A 2SA1514K Diode RLS4148 ZENER 5.6V 5% PHILIPS BZX84-C5 V6 ZENER 12V 5% PHILIPS BZX84-C12 ZENER 15V 5% PHILIPS BZX84-C15 FET IRF9640 IR P-CH TO220 FET IRF640 IR N-CH TO-220 C4 C5 C6 C2,3,7,8,9,10,11,15 C13 C1 C16,17 CAP,CA 100pF 50V 10% 1206 NP0 CAP,CA 22pF 50V 10% 1206 SMT NPO CAP,CA 560pF 50V 10% 1206 NPO CAP,CA 0.1uF 50V 20% 1206 Z5U CAP,CA 0.022uF 50V 10% 1206 X7R CAP,NP 0.1uF 100V 10% 1210 X7 CAP,E NP 10uF 100V 20% CAP,NP 0.1uF 200V 10% 1210 X7 R2,11,29,30 R7,9,25 R22,23 R31-46 R26 R6,13,16 R10 R24 R14,15,27,28 R3 R8 R1,5,12 R17 R4 R20,21 RES, 1.00K 1206 5% RES, 10.0K 1206 5% RES, 10.0 ohms 1206 5% RES, 1.20K 1206 5% RES, 20.0K 1206 5% RES, 2.20K 1206 5% RES, 2.70K 1206 5% RES, 300.0 ohms 1206 5% RES, 3.30K 1206 5% RES, 39.0K 1206 5% RES, 470 ohms 1206 5% RES, 4.70K 1206 5% RES, 47.0K 1206 5% RES, 4.70M 1206 5% RES, 47.0 ohms 1206 5% Ref. Designator Description
harman/kardon
Qty
4 3 2 16 1 3 1 1 4 1 1 3 1 1 2
1 1 1 8 1 1 2 1
1 3 2 2 2 6 2 2 2 1 1
Wafer 40PIN PITCH=2.54mm HR2*40 L1 Ferrite core LS-A6206-ST EFD-30 1 L2 Inductor 35uH 1 PCB TO H/S-2,PCB TO PCB/H-4 SCREW 3*8 6 TO HSQLC1004/ID150-1 SCREW M3*12 1
19
HKTS 10
harman/kardon
20
HKTS 10
harman/kardon
21
HKTS 10
harman/kardon
22