Text preview for : Alignment & Adjustment.pdf part of Samsung 910MP SM
Back to : Samsung SyncMaster 910MP. | Home
4 Alignments and Adjustments
4 Alignments and Adjustments
This section describes to adjust LCD monitor after replacing EEPROM, Main PBA or Panel.
4-1 DDC jig installation
Monitor
(need to adjust)
Parallel Cable
(25Pin)
PC system MTI-2055
(to input DDC data) DDC Manager
Signal Cable
4-2 How to execute DDC
1. Execute "WinDDC.exe"
4-1
4 Alignments and Adjustments
2. Click "Sys Config"
Select "Station : Write station".
Check "Serial No and Week : Don't change"
Click "Save"
3. Click "Open" icon.
Select "Connected Port #1" and Next "OK".
* File Name - 910MP.DDC : Analog
Press enter key on your keyboard.
4. Confirm the "DDC OK".
4-2
4 Alignments and Adjustments
4-3 Factory Mode Adjustments
4-3-1 Factory Mode Admission
Power off MUTE 1 8 2 Power on
4-3-2 Factory Mode OSD
DDP NCE-NA GAMMA
BLE BLE MODE
BLE GAIN
BLE TILT
STATIC BLE
CUT OFF-NA R CUT OFF
B CUT OFF
G CUT OFF
WHITE DRIVE -NA R DRIVE
B DRIVE
G DRIVE
LTI LTI CORING
LTI GAIN
CTI CTI CORING
CTI GAIN
PEAKING-NS Pos Peak
Neg Peak
Peak Coring
Adjust Misc-NS Brightness
Contrast
Saturation
Tint
Int. Brightness
VSP Part Brightness
Contrast
Cb Saturation
Cr Saturation
Tint
Sub Adjust V-Brightness
V-Contrast
V-Saturation
V-Tint
D-Brightness
D-Contrast
D-sharpness
D-Saturation
D-Tint
4-3
4 Alignments and Adjustments
Adjust R Offset
G Offset
B Offset
R Gain
G Gain
B Gain
PC/DTV Auto Color
Option Suwon America
Suwon Korea
Suwon Japan
Suwon PAL
SESK PAL
SEMEX America
......
Help Menu
Auto-Auto
Clear-EEPROM
Check Sum
Panel Information
Reset
Bus-Stop
4-4
4 Alignments and Adjustments
4-3-3 Adjustment(Applicabile Only to Micom Program Adjustments)
- PC Auto Color Adjustment
Service
DDP Part Ēš
VSP Part Ēš
Sud Adjust Ēš
Adjust Ēš
PC Auto Color Ēš
Option Ēš
Checksum Ēš
Panel Infomation Ēš
Reset Ēš
- You may not be able to perfrorm normal color adjustments with any
Bus-Stop Ēš
other patterns than with the 16-gray pattern.
2004/11/02
T-MAN19W-0802
PC Auto color
- PC analog : 1280 x 1024/60Hz, 16Gray Pattern
- Equipment Used : MSPG-3240L
4-3-3 Panel Information Adjustment(Applicable to Panel and lamp replacements)
- Panel Information, Reset
Service
Service
DDP Part Ēš
:
VSP Part Ēš
:
Sud Adjust Ēš
Adjust Ēš
Time ch. No
PC Auto Color Ēš :
Option Ēš :
Checksum Ēš :
Panel Infomation Ēš
Reset Ēš
Bus-Stop Ēš Panel Time Reset : Press the Enter key located on the front of the monitor and
hold it for five seconds.(Perform a panel time reset after a
panel replacement.)
2004/11/02
T-MAN19W-0802
Factory Reset : After performing a reset, turn the main power Off and then
ON again.
4-5
4 Alignments and Adjustments
Memo
4-6