Text preview for : PHILIPS 32PW8807.pdf part of Philips 32PW8807/12 S.M.
Back to : PHILIPS 32PW8807.part1.r | Home
Colour television
Chassis
EM3E
AA
CL 16532044_000.eps 150501
Contents
1 2 3 4 5 6 Technical Specifications, Connection Facilities and Chassis Overview Safety Instructions, Maintenance, Warnings and Notes Directions for Use Mechanical Instructions Service Modes, Error Codes, Faultfinding and Repair Tips. Block Diagrams Block Diagram (Supply, Deflection) Block Diagram (SSB Video) Block Diagram (SSB Audio) Supply Lines Overview Wiring Diagram I2C Overview Testpoint Overviews Electrical Diagrams and PWB lay-outs Main Supply (Diagram A1) Stand-by Supply (Diagram A2) Line Deflection (Diagram A3) Frame Deflection E/W Drive (Diagram A4) Rotation Circuitry (Diagram A5) Audio Amplifier (Diagram A6) Headphone Amplifier (Diagram A7) Tuner, I/O, SIMM (Female) (Diagram A8) Front (Diagram A10) Inputs / Outputs (Diagram A11) SIMM (Male) (Diagram B1) IF, I/O, Video Processing (Diagram B2) Featurebox (PICNIC) (Diagram B3) Video Control (HOP) (Diagram B4) Teletext & Control (OTC) (Diagram B5) Audio Demodulator (Diagram B6) Falconic (Diagram B8)
Page
2 4 6 20 23
Contents
Mains Switch Panel CRT Panel DC-Shift Panel I/O 3rd SCART Panel VDAF + 2nd Order S Panel Side I/O Panel Top Control 8 Electrical Alignments 9 Circuit Descriptions List of Abbreviations 10 Spare Parts List (Diagram E) (Diagram F) (Diagram G) (Diagram H) (Diagram I) (Diagram O) (Diagram P)
Page
74 76 78 80 82 84 86 87 94 109 111 74-75 77 78 81 83 85 86
7
35 36 37 38 39 40 41 Diagram 42 43 44 45 46 47 46 48 49 50 57 58 59 60 61 62 62
PWB 51-56 51-56 51-56 51-56 51-56 51-56 51-56 51-56 51-56 51-56 64-73 64-73 64-73 64-73 64-73 64-73 64-73
©
Copyright 2001 Philips Consumer Electronics B.V. Eindhoven, The Netherlands. All rights reserved. No part of this publication may be reproduced, stored in a retrieval system or transmitted, in any form or by any means, electronic, mechanical, photocopying, or otherwise without the prior permission of Philips. Printed in the Netherlands Subject to modification
Published by CO 0066 Service PaCE
3122 785 11360
GB 2
1.
EM3E
Technical Specifications, Connection Facilities and Chassis Overview
1. Technical Specifications, Connection Facilities and Chassis Overview
1.1
1.1.1
Technical Specifications
Reception Tuning system Colour systems : PLL : PAL B/G, D/K, I : SECAM B/G, D/K, L/L' : NTSC 4.43 (playback only) : FM-mono B/G : FM-mono D/K : FM-mono I : AM-mono L/L' : 2CS B/G : 2CS/Chez D/K : NICAM B/G : NICAM D/K : NICAM I : NICAM L : PAL B/G, D/K, I : SECAM B/G, D/K, L/L' : NTSC 4.43 (playback only) : 100 channels : VHF, UHF, SChannels and Hyperband : 75 W, Coax : 0 and 90 - 99 1.2.2
3 -Y 4 - C / 16:9 5 -
Rear Connections
Sound systems
EXT3
SURR. L SERVICE CONNECTOR R AUDIO OUT EXT1 EXT2
A/V connections
CL16532044_002.eps 090501
Figure 1-2
Aerial input VCR preselections 1.1.2 Miscellaneous Mains voltage Mains frequency Ambient temperature Maximum humidity Standby Power consumption
External 1 (in/out): RGB/YUV + CVBS
1 21
: : : : :
220 - 240 V (± 10 %) 50 / 60 Hz (± 5 %) + 5 to + 45 deg. C 90 % R.H. 1W
2
20
CL96532137_056.eps 171199
Figure 1-3 1 2 3 4 5 6 7 8 - Audio - Audio - Audio - Audio - Blue / U - CVBS-status
1.2.1
Front Controls / Side Connections
FRONT CONTROL
SIDE I/O
3.5 AUDIO R AUDIO L VIDEO SVHS
STANDBY LED SK 1 IR-RECEIVER
CL16532044_001.eps 260401
Figure 1-1
GND GND
SVHS (in) 1 2 -
Audio / Video In - - Video - - Audio - - Audio - - Headphone
CVBS (1 Vpp / 75 W) L (0.5 Vrms / 10 kW) R (0.5 Vrms / 10 kW) (32 - 2000 W / 10 mW)
9 1011- Green / Y 12131415- Red / V 16- RGB-status 171819- CVBS 20- CVBS 21- Earth
(0.7 Vpp / 75 W) GND GND (0.7 Vpp / 75 W) 0 - 0.4 V: INT 1 - 3 V: EXT / 75 W GND GND (1 Vpp / 75 W) (1 Vpp / 75 W) GND
1.2
Connection Facilities
R (0.5 Vrms / 1 kW) R (0.5 Vrms / 10 kW) L (0.5 Vrms / 1 kW) GND GND L (0.5 Vrms / 10 kW) (0.7 Vpp / 75 W) 0 - 1.3 V: INT 4.5 - 7 V: EXT 16:9 9.5 - 12 V: EXT 4:3 GND
Channel selections
Audio Out - - Audio - - Audio - - Audio
Surr. (0.5 Vrms / 1 k W) L (0.5 Vrms / 1 kW) R (0.5 Vrms / 1 kW)
(1 Vpp / 75 W) (0.3 Vpp / 75 W) GND
Technical Specifications, Connection Facilities and Chassis Overview
External 2 (in/out): SVHS + CVBS (intended for VCR)
1 21
EM3E
1.
GB 3
External 3 (in): CVBS
1 21
2
20
CL96532137_056.eps 171199
2
20
CL96532137_056.eps 171199
Figure 1-4 1 2 3 4 5 6 7 8 Audio Audio Audio
Figure 1-5
GND GND L (0.5 Vrms / 10 kW) 0 - 1.3 V: INT 4.5 - 7 V: EXT 16:9 9.5 - 12 V: EXT 4:3 GND
GND GND
GND GND (1 Vpp / 75 W)
1.3
Chassis Overview
TOP CONTROL PANEL
P P
F O
CRT/SCAVEM PANEL
SIDE I/O PANEL
B
SMALL SIGNAL BOARD
MAINSWITCH PANEL
E
H
3rd SCART
LARGE SIGNAL PANEL
A
DAF PANEL
I
CL 16532044_004.eps 140501
Figure 1-6
9 1011121314151617181920- CVBS 21-
R (0.5 Vrms / 1 kW) R (0.5 Vrms / 10 kW) L (0.5 Vrms / 1 kW) GND GND Audio L (0.5 Vrms / 10 kW) C (0.7 Vpp / 75 W) CVBS-status 0 - 1.3 V: INT 4.5 - 7 V: EXT 16:9 9.5 - 12 V: EXT 4:3 9 GND 10Easy link (P50) 111213GND 14GND 15- C (0.7 Vpp / 75 W) 1617GND 18GND 19- CVBS (1 Vpp / 75 W) 20- Y / CVBS (1 Vpp / 75 W) 21GND
1 2 3 4 5 6 7 8
- Audio - Audio - CVBS-status
R (0.5 Vrms / 10 kW)
GB 4
2.
EM3E
Safety & Maintenance instructions, Warnings and Notes
2. Safety & Maintenance instructions, Warnings and Notes
2.1 Safety instructions for repairs
Safety regulations require that during a repair: · Due to the chassis concept, a very large part of this chassis (incl. deflection) is 'hot'. Therefore the set must be connected to the mains via an isolating transformer. , should · Safety components, indicated by the symbol be replaced by components identical to the original ones. · When replacing the CRT, safety goggles must be worn. Safety regulations require that after a repair, the set must be returned in its original condition. In particular attention should be paid to the following points: · General repair instruction: as a strict precaution, we advise you to resolder the solder joints, through which the horizontal deflection current is flowing, in particular: All pins of the line output transformer (LOT); Fly-back capacitor(s); S-correction capacitor(s); Line output transistor; Pins of the connector with wires to the deflection coil; Other components through which the deflection current flows. Note: This resoldering is advised to prevent bad connections due to metal fatigue in solder joints and is therefore only necessary for television sets older than 2 years. · The wire trees and EHT cable should be routed correctly and fixed with the mounted cable clamps. · The insulation of the mains lead should be checked for external damage. · The mains lead strain relief should be checked for its function in order to avoid touching the CRT, hot components or heat sinks. · The electrical DC resistance between the mains plug and the secondary side should be checked (only for sets which have a mains isolated power supply). This check can be done as follows: Unplug the mains cord and connect a wire between the two pins of the mains plug; Set the mains switch to the 'ON' position (keep the mains cord unplugged!); Measure the resistance value between the pins of the mains plug and the metal shielding of the tuner or the aerial connection on the set. The reading should be between 4.5 MW and 12 MW. Switch off the TV and remove the wire between the two pins of the mains plug. · The cabinet should be checked for defects to avoid touching of any inner parts by the customer.
2.3
Warnings
· In order to prevent damage to IC's and transistors, all high-voltage flashovers must be avoided. In order to prevent damage to the picture tube, the method shown in Fig. 2-1 should be used to discharge the picture tube. Use a high-voltage probe and a multimeter (position VDC). Discharge until the meter reading is 0 V (after approx. 30 s).
·
·
· · ·
·
2.2
Maintenance instructions
It is recommended to have a maintenance inspection carried out by a qualified service employee. The interval depends on the usage conditions: · When the set is used under normal circumstances, for example in a living room, the recommended interval is 3 to 5 years. · When the set is used in circumstances with higher dust, grease or moisture levels, for example in a kitchen, the recommended interval is 1 year. · The maintenance inspection contains the following actions: Execute the above-mentioned 'general repair instruction'. Clean the power supply and deflection circuitry on the chassis. Clean the picture tube panel and the neck of the picture tube.
V
CL96532156_040.eps 140501
Figure 2-1 All IC's and many other semiconductors are susceptible to electrostatic discharges (ESD). Careless handling during repair can reduce life drastically. When repairing, make sure that you are connected with the same potential as the mass of the set by a wristband with resistance. Keep components and tools also at this same potential. Together with the deflection unit and any multipole unit, the used flat square picture tubes form an integrated unit. The deflection and the multipole units are set optimally at the factory. Adjustment of this unit during repair is therefore not recommended. Be careful during measurements in the high-voltage section and on the picture tube. Never replace modules or other components while the unit is switched ON. When making settings, use plastic rather than metal tools. This will prevent any short circuits and the danger of a circuit becoming unstable. Wear safety goggles during replacement of the picture tube.
Safety & Maintenance instructions, Warnings and Notes 2.4 Notes
· The direct voltages and oscillograms should be measured with regard to the tuner earth ( ) or hot earth ( ). The direct voltages and oscillograms shown in the diagrams are indicative and should be measured in the Service Default Mode (see chapter 5) with a colour bar signal and stereo sound (L: 3 kHz, R: 1 kHz unless stated otherwise) and picture carrier at 475.25 MHz. Where necessary, the oscillograms and direct voltages are measured with ( ) and without ( ) aerial signal. Voltages in the power supply section are measured both for normal operation ( ) and in Standby ( ). These values are indicated by means of the appropriate symbols. The picture tube PWB has printed spark gaps. Each spark gap is connected between an electrode of the picture tube and the Aquadag coating. The semiconductors indicated in the circuit diagram and in the parts lists are completely interchangeable per position with the semiconductors in the unit, irrespective of the type indication on these semiconductors. Manufactured under license from Dolby Laboratories Licensing Corporation. DOLBY, the double D symbol and PRO LOGIC are trademarks of Dolby Laboratories Licensing Corporation.
EM3E
2.
GB 5
·
·
·
·
·
GB 6
Preparation
Preparation &
Place the TV on a solid surface.
3.
Your remote control
EasyLink p. 25 ® INSTANT recording
Installation p. 4
EM3E
yÚ
U
h
3. Directions for use
B switch to standby p. 9
min. 1m
B
Q surround modes p. 9
MODE
DVD/Satellite selection p. 25
INSTANT
Q
®
Ò
yÚ
VCR
Videorecorder selection p. 24 Audio/video equipment p. 24-25
U
f
h
Teletext p. 19-20
æ
b
NEXTVIEW/TXT
guide on/off æ subpage selection solution to puzzles enlarge
MENU
OK
b teletext on/off C time display
Colour keys - NEXTVIEW selection p. 15 - direct teletext page or subject selection, p. 19
CABLE
p. 15
main menu on/off Zoom p. 9
MENU
f h
For ventilation, leave at least 5 cm free all around the TV. Do not place the TV on a carpet. To prevent any unsafe situations, do not place any objects on top of the TV. Avoid heat, direct sunlight and exposure to rain or water.
é "
p. 11
h
Insert the aerial plug firmly into the aerial socket x at the back of the TV. Insert the mains plug in the wall socket having a mains voltage of 220V-240V. To prevent damaging the mains (AC) cord which could cause a fire or electric shock, do not place the TV on the cord. Remote control: Remove the cover of the battery compartment. Insert the 2 batteries supplied (Type R6-1.5V).
V
¬
P
Directions for use
volume up/down p. 9 sound mute p. 9
V ¬
1
2
3
Cursor to select your choice p. 4 OK activate your choice
programme selection p. 9 on screen info p. 9 previous programme p. 9 video recorder function
P
4
5
6
`
i 0
7
8
9
i
0
0
X
S
b
X bilingual choice / sound info p. 10
SMART
The batteries supplied do not contain the heavy metals mercury and cadmium. Nevertheless in many countries exhausted batteries may not be disposed of with your household waste. Please check on how to dispose of exhausted batteries according to local regulations. Note: this remote control functions with TVs which use the RC6 signalling standard.
R6 / 1,5 V
Peripherals p. 24 w selection of EXT1, EXT2, EXT3 or FRONT
w
M
a
q
S
h
smart sound p. 10 M smart picture p. 10 a
ACTIVE CONTROL
b
TXT language group selection p. 19 freeze the picture p. 10 hold teletext page p. 20 dual screen p. 14
(
q picture format, p. 10
h active control on/off p. 10
Switch the TV on : Press the power switch A on the front of your TV. A green indicator on the front of the TV lights up and the screen comes on. If the TV is in standby mode (see p. 9), press the - P+ key on the remote control. The red lamp blinks every time you press a key on the remote control. When you switch on your set for the first time, the menu LANGUAGE automatically appears on the screen.The explanation appears in different languages one at a time. Choose your own language and press the OK key on the remote control. Go on to page 4, Store TV channels.
2
Preparation
Preparation
3
Installation
Automatic installation
Automatic installation Start J Stop K
B
Select the INSTALLATION menu
INSTANT
Q
In the Automatic installation menu select Start and press the OK key to activate the searching. All TV channels are searched for and stored automatically.
®
Ò
yÚ
U
f
h
æ
b
Press U and h at the same time.
TV is searching One moment please ...
MENU
OK
To use the menus
Automatic installation J Start Stop K
&
If a cable system which broadcasts ACI (Automatic Channel Installation) or a TV channel transmitting a teletext page with the frequencies and programme names of all the TV channels which can be received, is detected, the search is stopped and a programme list appears. The programme list is automatically filled with all the programme numbers and names of the TV channels transmitted.
Use the cursor in the up/down, left/right directions to select a menu item.
B
é
1 BBC1 2 BBC2 3 CNN .... ....
Press the OK key to activate.
INSTANT
Q
return or switch main menu off
It is possible that the cable company or the TV channel displays a broadcast selection menu. Layout and items are defined by the cable company or the TV channel. Make your choice with the cursor and press the OK key. To exit from the menu press the MENU key on the remote control. Go on to page 6.
®
Ò
"
Use the MENU key to return or to switch the menu off.
yÚ
U
f
h
æ
b
activate
MENU TITLE
MENU
OK
select menu item
L M
Manual installation
Searching for and storing TV channels is done channel by channel. You must go through every step of the Manual installation menu.
Selection mode is only present and lights up if the country selected also
Manual installation
V
P
¬
Subject Subject Subject J Subject Subject Subject
1 2 3 4 5 6
1
2
3
4
5
6
7
8
9
Store TV channels
(Selection mode) J System System K Programme no. Search Fine tune Store
offers the channel option (C-channels for aerial channels, S-channels for cable channels). You can choose either channel or frequency mode.
Directions for use
After the new or extra TV channels have been stored, the TV automatically transfers those TV channels to the video recorder if it is equipped with the EasyLink function. The message EasyLink : downloading ...... appears on the screen. The programme list of the video recorder is now the same as the one of the TV. If the TV is connected to a video recorder which supports the NEXTVIEWLink function, the TV also automatically transfers the language and country selections to the video recorder.
&
Select the TV system Select the country or part of the world from where you want to receive the TV channel. If you are connected to a cable system, select your country or part of the world where you are now located.
é "
Press the cursor down and enter the programme number with the digit keys.
Select the menu language and country
J MENU TITLE INSTALLATION
First, select your language and country.
Search for a TV channel Press the cursor left/right. The frequency or the channel number increases until a TV channel is found.
Menu language
&
Select Menu language and press the OK key.
EM3E
é
J MENU TITLE Menu language
Select your language and press the OK key. Use the cursor up/down to scroll through the list and to bring up other languages which are not displayed on the screen at present.
Direct selection of a TV channel If you know the frequency, the C- or S-channel number, enter it directly with the digit keys 0 to 9. Ask for a list from your cable company or dealer, alternatively consult the Table of frequencies on the inside backcover of this handbook.
English .... ....
"
Select Country and press the OK key.
`
`
Fine tune In case of poor reception, you can improve the reception by adjusting the frequency with the cursor left/right.
J MENU TITLE Country
Select the country where you are now located and press the OK key. Use the cursor up/down to scroll through the list and bring up other countries which are not displayed on the screen at present.
(
To store your TV channel, select Store and press the OK key.
Select Other when none of the countries applies. Repeat steps
3.
United Kingdom .... ....
& to ( to store another TV channel. §
To exit from the menu press the MENU key on the remote control.
You can now search for and store the TV channels in two different ways: using automatic installation or manual installation (tuning-in channel by channel). Select your choice and press the OK key.
GB 7
4
Installation
Installation
5
GB 8 3.
Give name
INSTALLATION Menu language Country Automatic installation Manual installation Give name Reshuffle Favourite programmes J SETUP
Install TV Setup
The Setup menu allows you to adjust initial settings, i.e. those which are not related to the installation of the TV channels. The Setup menu contains items that control the settings of the TV's functions, features, services and peripherals you may have connected. Use the cursor in the up/down, left/right directions to select the menu item. Use the OK key to activate. Use the MENU key to return or switch menu off.
INSTALLATION
Menu language Country
It is possible to change the name stored in the memory or to assign a name to a TV channel which has not yet been entered. A name with up to 5 letters or numbers can be given to the programme numbers 0 to 99. For example SUPER, BBC1,... Between 99 and 0 you can also name any peripherals that are connected to a euroconnector.
Select Give name in the INSTALLATION menu and press the OK key.
EM3E
Automatic installation Manual installation J Give name Reshuffle Favourite programmes SETUP
Select the programme number.
Press the OK key.
SETUP
Select the character with the cursor up/down. Digital sources (for future use)
yes/no
& é "
Select the following position with the cursor right.
Give name
Select the following character.
& é " ` ( § è !
Digital Sources J Decoder/Descrambler Picture tilt Information line Factory settings Auto format Auto Surround INSTALLATION Decoder/Descrambler J Programme Decoder status
Press the OK key when finished.
Press the MENU key to return to the INSTALLATION menu.
EXT1 EXT2 EXT3 FRONT J 0 1 BBC1 2 BBC2 3 .... 4 .... 5 ....
Space, numbers and other special characters are located between Z and A.
Define Decoder/Descrambler programme numbers If a decoder or a descrambler is connected, see p. 22 you can define one or more programme numbers as decoder programme numbers.
Reshuffle the programme list
Press the cursor left/right to select the input used to connect to your decoder Off, EXT1 or EXT2. Select Off if you do not want the selected programme number being activated as a decoder programme number.
According to your preference you can change the order of the stored TV channels.
Reshuffle
Directions for use
Select Reshuffle in the INSTALLATION menu and press the OK key.
Select EXT2 when the decoder is connected to your EasyLink video recorder. When selecting the decoder, the message EasyLink: downloading presets.... appears on the screen.
Select the programme number you want to exchange. Picture tilt Select Picture tilt with the cursor up/down. Keep the cursor left/right pressed to adjust the rotation of the picture.
Press the OK key.
EXT1 EXT2 EXT3 FRONT 0 J 1 CNN 2 BBC2 3 .... 4 .... 5 ....
& é " ` (
Select the new number you want to exchange it with.
Press the OK key. Repeat the operation until all TV channels are allocated as you like.
§
Press the MENU key to return to the INSTALLATION menu.
Select Favourite TV channels
After leaving the installation you can browse through the TV channels by pressing the - P + key. Only those TV channels which are in the favourite list will be displayed. Non-favourite TV channels can still be selected with the digit keys. By default all stored channels are added to the favourite list.
Information line Select On and after the selection of a TV programme or after pressing the i key on the remote control, a TV channel which broadcasts teletext may transmit the name of the TV channel, the programme name or another message.This is displayed on screen next to information about sound and picture format. When selected Off, only sound and picture format information is displayed after the selection of a TV channel or after pressing the i key.
Favourite programmes
&
Select Favourite programmes in the INSTALLATION menu and press the OK key.
Factory settings Select Factory settings and press the OK key to restore picture and sound settings, predefined in the factory.
Select your favourite programme number.
0 ... 1 ... J 2 ... 3 .... 4 .... 5 ....
No Yes Yes No No Yes
é " `
Select Yes or No with the cursor left/right.
Repeat for every TV channel you want to make a favourite or a non-favourite TV channel.
(
Press the MENU key to return to the INSTALLATION menu.
Auto format Selecting Yes causes the screen to automatically fill as much of the picture as possible when TV programmes are not carrying special signals detecting the correct screen format. With the q key on the remote control you can still select other picture formats. See p. 10.
In order for NEXTVIEW to function properly, the first TV channel from the favourite list should also broadcast the correct local date and time via teletext.
6
Installation
Installation
7
Operation
Use of the remote control
SETUP
Auto Surround Sometimes the broadcaster transmits special signals for Surround Sound encoded programmes. In that case, the TV automatically switches to the best Surround Sound mode when Auto Surround is switched on. Virtual Dolby* Surround will be reproduced, see p. 9. Overruling this surround mode remains possible.
® Instant record If your video recorder has the EasyLink function the INSTANT ® key for record can be operated in the TV mode.
®Ò Video recorder see p. 24
B
Digital Sources Decoder/Descrambler Picture tilt Information line Factory settings Auto format J Auto Surround INSTALLATION
yes/no
Installation Select Installation and press the OK key to return immediately to the INSTALLATION menu.
B
INSTANT
` æ
NEXTVIEW/TXT
®
To exit from the menu press the MENU key repeatedly. guide on/off see p. 15
Q
Ò
yÚ
Standby The set is switched off.To switch the TV on again, press - P + or the digit keys. If your EasyLink video recorder has the system standby function and you press the standby key for 3 seconds, both the TV and video recorder are switched to standby. Your TV consumes energy in the standby mode. Energy consumption contributes to air and water pollution. We advise to switch off your TV overnight instead of leaving it on standby.You save energy.
U æ f h b
MENU
MENU
Main menu on/off see p. 11
OK Press this key to activate your choice, when in the menus. Volume Press + or - to adjust the volume.
OK
Q Surround modes
Incredible Surround
V
V
P
¬
¬
With stereo transmission, and when Incredible Surround is selected, it seems as though the loudspeakers are spread further apart from one another.
1 4 7
i
X
w
2 5 8 0
S
SMART
3 6 9
Mute Temporarily interrupt the sound or restore it.
Virtual Dolby Surround (optimal with Dolby Surround signals)
P
Programme selection To browse through the TV channels activated in the Favourite Programme menu.
0
b M h a q
Virtual Dolby Surround enables you to experience the effect of Dolby Surround Pro Logic, reproducing a rear sound effect. See Sound menu,Virtual Dolby effect, p. 12.
b i
Screen information Press for 5 seconds to activate/de-activate the extended or reduced display of TV channel and programme information on the screen. Press briefly to display information about the selected TV channel and programme, the sound reception, picture settings and the remaining time set with the sleeptimer.
ACTIVE CONTROL
Directions for use
Teletext on/off see p. 19
fh
Teletext functions see p. 20
EM3E
h Zoom Press the ZOOM h key repeatedly to select one of the zoom magnifications (x1, x4, x9, x16). Additionally you can shift the selected zoom window over the screen with the cursor. Press i to activate/de-activate the continuous display of the zoom magnification. The zoom window is reset after: selecting another TV channel, another picture format or when another picture format is selected automatically. Zooming is disabled in Dual screen mode. 0/9 Digit keys To select a TV channel. For a two digit programme number, enter the second digit within 2 seconds. To switch immediately to a selected one digit TV channel, keep the digit key pressed a bit longer. 0 Previous programme The previously selected TV channel is displayed. The indication is only video recorder. U
`Dolby' `Pro Logic' and the double-D symbol are trademarks of Dolby Laboratories Licensing Corporation. Manufactured under license from Dolby Laboratories Licensing Corporation.
3.
Time display The time, downloaded from the TV channel (with teletext) stored on programme number 1 or the lowest favourite programme number, is displayed on the screen. This function is not available when continuous subtitles have been switched on.
GB 9
8
Installation
Use of the remote control
9
GB 10 3.
Use of the menus
B
INSTANT Q
®
yÚ
Ò
return or switch main menu on/off
U æ b
MENU
f
h
& é
Press the MENU key to display/cancel the MAIN MENU. Press the cursor right to activate the selected menu.
X
OK
OK key to activate
Use the cursor in the up/down directions to select the PICTURE, SOUND or FEATURES menu or to select the PROGRAMMES. Use the cursor in the up/down, left/right directions to select the menu item. Use the OK key to activate. Press the MENU key repeatedly to return or to switch the menu off.
EM3E
B
V P
¬
Q
cursor to select adjustments
INSTANT
" ` ( §
®
Ò
1
MAIN MENU J Contrast PICTURE SOUND FEATURES PROGRAMMES
2
3
yÚ
U b
f
h
w
OK
æ
Select peripherals Press this key repeatedly to select EXT1, EXT2, EXT3 or FRONT, according to where you connected the peripherals (p. 24).
MENU
Bilingual choice and sound mode selection Press this key · to switch from Stereo to Mono sound, in case of stereo transmission, or from Nicam Stereo to Nicam available, in case of digital transmission; · to choose between language Y (Dual Y) or language Z (Dual Z), in case of bilingual transmission.The setting is separately stored for each TV channel.
Picture menu
If an NTSC peripheral is connected to one of the euroconnectors, the option Hue also appears. Tint Select the colour temperature: Normal, Warm or Cool.
M
V P
¬
S Freeze To activate/de-activate the frozen picture or to hold a teletext page.
PICTURE
1 5 8
2 6 9
0
b a h q
3
4
b
Dual screen, see p. 14
7 0
S
SMART
Directions for use
i
X
J Contrast L Brightness Colour Sharpness Tint Digital options Dynamic Contrast
Digital options Although Natural Motion is the most ideal setting, it may be preferable to switch back to Digital Scan and/or 100 Hz. To make all the 3 digital options available at the same time and selectable, first select a 4:3 picture format.
w
M
Smart Keys To select predefined picture and sound settings.
ACTIVE CONTROL
M Smart Sound Each time it is pressed, a different sound setting is selected, corresponding with specific factory settings of the equalizer.
· 100 Hz = 100 Hz only (Field flicker reduction) · Dig. Scan = 100 Hz + Dig. Scan (Field and line flicker reduction) · Natural Motion = 100 Hz + Dig. Scan + Natural Motion (Field and line flicker reduction and smooth movement reproduction) · Double lines = provides for a doubling of vertical resolution which adds astonishing sharpness and a total absence of visible picture lines. Motion compensation reduces jitter and offers smooth, yet sharp motion reproduction. Note: if the menu item Digital options is not present, first select a 4:3 picture format with the q key.
a Smart Picture Each time it is pressed, a different picture setting is selected, corresponding with specific factory settings of Contrast, Colour, Sharpness and Dynamic Contrast.
q Picture format Press this key repeatedly to select another picture format: 4:3, Movie Expand 14:9, Movie Expand 16:9 with or without subtitling, Wide Screen, Super Zoom or Automatic (when Auto format is set to Yes in the SETUP menu). Automatic makes the picture to fill the screen as much as possible. Sometimes also video recorder programmes carry special signals which will automatically switch the TV to the correct screen format. Auto format is disabled when in Dual screen. When in Movie Expand 14:9 or 16:9 or Super Zoom picture format you can make subtitles visible with the cursor up/down.
Dynamic Contrast To make the contrast in the darker and the brighter picture areas more noticeable, select the Med setting. In certain circumstances it may be preferred to select Min, Max or Off. The modified adjustments for Contrast, Brightness, Colour, Sharpness,Tint, Digital Scan and Dynamic Contrast are automatically stored for all TV channels. Select Factory settings in the Setup menu to restore the predefined factory settings, see p. 7.
Personal refers to the personal preference settings of picture and sound selected in the picture and sound menu. Remark: the moment you are in a predefined smart sound or picture setting and you modify a setting in the picture or sound menu, all values of the menu will overwrite the previously made settings.
h Active control Active control is a pro-active and automatic system.The TV continuously measures and corrects all incoming signals in order to provide the best picture possible. Press the h key to select the Active Control values Off or On. Off Sharpness and Dynamic Contrast are controlled automatically On Sharpness, Dynamic Contrast and Noise Reduction are controlled automatically. Press the cursor in the up/down directions while the selected Active Control setting information is on top of the screen. The Active Control menu appears. The picture settings are being adapted continuously and automatically. The menu items cannot be selected. Press the cursor in the up/down directions again to switch off the menu.
10
Use of the remote control
Use of the menus
11
Sound menu
B
INSTANT Q
B
®
yÚ
Features menu
&
Press the MENU key to display/cancel the MAIN MENU. Use the cursor in the up/down directions to select the FEATURES menu. Use the cursor in the up/down, left/right directions to select the menu item. Use the OK key to activate. Press the MENU key repeatedly to return or to switch the menu off.
INSTANT
Q
®
Ò
return or switch main menu on/off
Ò
yÚ
Press the MENU key to display/cancel the MAIN MENU.
U æ
MENU
return or switch main menu on/off OK key to activate
U b
f
h
f
h
æ
b
OK key to activate
OK
Use the cursor in the up/down directions to select the SOUND menu.
MENU
OK
Use the cursor in the up/down, left/right directions to select the menu item. cursor to select adjustments
V P
¬
P
cursor to select adjustments
V
& é " ` ( é " ` (
Use the OK key to activate.
Press the MENU key repeatedly to return or to switch the menu off.
¬
The modified adjustments for Volume, Balance, and Graphic equalizer are automatically stored for all TV channels. Select Factory settings in the Setup menu to restore the predefined factory settings, see p. 7.
J FEATURES Sleeptimer Child lock Subtitle Off Off Off
SOUND
J Volume L Balance Graphic Equalizer Headphone Volume AVL Delta volume Virtual Dolby effect
M
Graphic Equalizer Here you can select the preferred sound setting which corresponds with the personal sound settings.
Sleeptimer With the sleeptimer you can set a time period after which the TV should switch itself to standby. The counter runs from Off up to 180 min. One minute before the TV is set to go to standby, the remaining seconds appear on screen. Not visible in dual screen mode.You can always switch off your set earlier or change the set time.
Headphone volume See Connect Peripheral Equipment, p. 23, for the connection of the headphone.
Directions for use
AVL (Automatic Volume Leveller) AVL automatically controls the volume level to avoid too large level differences, especially when switching to another programme or during commercial breaks. AVL will reduce the dynamics of the sound.To maintain original dynamics, use the Delta volume feature.
Child lock If the child lock is on, the TV can only be switched on with the remote control.The P - and + keys on top of the TV cannot be used to select a TV channel. In this way you can prevent unauthorised use of your TV. If the message Child lock On appears, the child lock must be switched off before you can use the P - and + keys on top of the TV to select a TV channel. Subtitle TV channels with teletext often transmit certain programmes with subtitling. See Teletext, Continuous Subtitles, p. 21 how to select the proper subtitle page from the teletext index. Select Subtitle On or Off. Press the MENU key to switch off the Features menu.
Delta volume Here you may adjust the volume differences of each selected TV channel or external device separately.This can compensate volume differences between different broadcasters. Use the - P + keys to compare to the volume of other TV channels or externals.
Programme list
Press the MENU key to display/cancel the MAIN MENU. Select PROGRAMMES with the cursor up/down. Press the cursor right to display an overview of all the TV channels installed. Press the cursor up/down to run through the list and press OK to select the desired TV channel.
EM3E
Virtual Dolby effect Virtual Dolby enables you to experience the effect of Dolby Surround Pro Logic without the need of having rear speakers connected or activated. Select the level of Virtual Dolby effect with the cursor left/right.
& é " ` (
Press the MENU key to switch off the Programme list.
3.
GB 11
12
Use of the menus
Use of the menus
13
GB 12 3.
NEXTVIEW
/ Teletext Guide
Dual Screen
&
B
INSTANT
Q
®
Ò
Today, most broadcasters in Europe, are offering teletext pages containing their programme schedule of today.These pages can be requested by switching the TV to Teletext Guide. An increasing number of broadcasters are offering an extended programme guide service called NEXTVIEW. NEXTVIEW is a new way of presenting programme schedules and offers more features than common teletext. With NEXTVIEW it is possible to show for instance all the movies coming tonight.
yÚ
EM3E
æ
U
f
h
b
æ
b
MENU
OK
Press the b key to switch on Dual Screen. The TV screen is divided into 2 parts: - the left side for the normal main picture, - the right side for teletext broadcast by the selected TV channel or for NEXTVIEW/Teletext Guide. To operate NEXTVIEW/Teletext Guide, see p. 15. To operate teletext, see p. 19. If Dual Screen is Off, the picture, teletext or NEXTVIEW/Teletext Guide are displayed full screen.
é
V
P
Press the q key to select a vertical squeezed or a non vertical squeezed picture size
¬
1
2
3
"
Press + P - to run through the teletext pages.
4
5
6
7
8
9
`
NEXTVIEW
i
0
B
0
X
S
b
b
selection
INSTANT Q
When in Teletext Dual Screen, press the b key to return to a full picture screen or press the b key to return to a full Teletext screen.
SMART
(
yÚ
w
M
a
q
Both facilities are integrated in this TV: NEXTVIEW and Teletext Programme Guide. If a TV channel supports NEXTVIEW then the TV will automatically present the NEXTVIEW programme schedule. If the TV channel supports just teletext, then the TV will switch automatically to Teletext Guide. Both facilities are offering the same functions: record, remind and info. However in case of Teletext Guide the broadcaster is responsible if these functions are possible. You can search for the programmes you want to watch up to 7 days in advance. It is also possible to search for a programme by theme, e.g. sport, movie, etc. Once a programme has been selected it can be tagged, to remind you, or to record on the video recorder automatically (provided the video recorder is equipped with NEXTVIEWLink Level 2.0), once, daily, weekly or series. Teletext Guide/NEXTVIEW also allows direct access to detailed information about programmes if provided by the broadcaster.
h
When in NEXTVIEW/Teletext Guide Dual Screen, press the æ key to return to a full picture screen or press the b key to return to a full NEXTVIEW/Teletext Guide screen.
ACTIVE CONTROL
q æ
U æ
MENU
f b
h
The broadcaster is responsible for the contents of the information. The TV is responsible for the capture of that information and for the presentation to the user.
OK
Directions for use
MENU
cursor to select adjustments
Use of the Teletext Guide/NEXTVIEW menus
V P
¬
& é
Press the æ key on the remote control to display/cancel the Teletext Guide/ NEXTVIEW menu.
1 4 7
2 5 8 0 9 6
3
Use the cursor in the up/down, left/right directions to select the date, CHANNEL for the channel guide, THEME for the theme guide, OVERVIEW for an overview of all the programmes which are marked as reminders or for recording, the programme guide page number or to enter the programme list.
NEXTVIEW
Channel Overview BBC1 BBC2 p.202 p 01 02 ... Monday 9 Oct Channel Theme BBC1 18:03 Overview
NEXTVIEW
Teletext Guide
Record Remind Info
11.03 14.35 17.50
BBC1 ................ ................ 226/3 ................ 231
Record Remind Info
What's on now Preview Themes Ratings
" ` ( § è
Enter the proper programme guide page number with the digit keys or with the P + keys. Press the cursor left/right to run through the subpages. Select a programme with the cursor up/down. Press one of the colour keys to select one of the basic functions (if available); record, remind, info. See Basic functions further on. Press the OK key to return to the header area again.
" ` (
Select a programme with the cursor up/down. Press one of the colour keys to select one of the basic functions (if available); record, remind, info. See Basic functions further on. Press the OK key to return to the header area again.
14
Dual Screen
NEXTVIEW
15
Teletext guide Basic functions
Channel BBC 1 p.202 CHANNEL 11.03 14.35
pOnce Daily
Theme Overview BBC 2 CNN p 01 02 ... Date THEME CNN Travel Guide R ! World news Weekly Clear time OVERVIEW
The functions Record, Remind and Info can be activated with the corresponding colour keys on the remote control. If the function is not available, then the text is shown at reduced brightness. Select a programme with the cursor up/down. Record R or Remind !
Record Remind Info Record Remind Info
11.03
BBC 2 ................
&
14.35 17.50 17.50 Insight ............................ Info block
................ 226/3 ................ 231
TV channels which broadcast teletext also transmit a page with the programme guide of the day. For each selected TV channel the programme guide page can be selected with the æ key: - automatically if the selected TV channel supports services like PDC (Programme Delivery Control) or MIP (Magazine Inventory Page). - if automatic pre-selection is not possible then the index page is displayed and the proper programme guide page number of the selected TV channel has to be entered with the digit keys. The programme guide page will be stored automatically only if it satisfies Video Programming via Teletext (VPT) requirements.
One moment please
Every time you press the æ key, the programme guide page of the selected TV channel will be available if the TV channel does not support NEXTVIEW.
Press the red colour key to activate Record or the green colour key to activate Remind. If the programme number of the broadcaster is not yet known, a message appears with the request to input the correct programme number with the cursor left/right and press OK. A small menu pops up in which you can choose the interval: once, daily or weekly, or clear an earlier made record or remind setting.The default interval is set to Once. If a programme is an episode of a series, it is identified by the system and the options daily and weekly are replaced by the option series. In this case the system identifies when the next episode of the series will be broadcast.This is not possible in the Teletext guide.
é "
Use the cursor in the left/right directions to select the interval. The colour of the tag refers to the interval. Press the OK key. When Record R is activated: Storing is displayed to indicate the video recorder is programmed. When Remind ! is activated:
The function items record, remind and info, corresponding with the coloured keys, become highlighted if the displayed programme page satisfies the Video Programming via Teletext (VPT) requirements. Select a programme item and press one of the function keys, e.g. Record or Remind. See Basic functions further on. The Info item is enabled if the selected programme contains a page number with an optional subcode referring to a page with more info about the programme.
Monday 9 Oct Channel Theme
18:03 Overview
NEXTVIEW
modes to sort and represent information
BBC1
CNN
BBC2
Record Remind Info
BBC1
NEXTVIEW
Directions for use
........ ........ ........
Channel The Channel guide provides an overview of all programmes that are broadcast by a single channel during one day. Already passed programmes can be made visible via cursor up. The list will start with the earliest broadcast programme. With cursor left/right another favourite TV channel can be selected.
- a message will be displayed the moment the tagged programme with ! starts, when watching the TV later on. - the TV switches on the moment the tagged programme with ! starts, when the TV is in standby. Note: Recordings and reminders are not possible when the broadcaster does not transmit dates and times of the programmes. The message No TV programming possible appears. Make sure you are on the TV programming page.
&
Monday 9 Oct Channel Theme
18:03 Overview
Culture
Movie
....
Info Press the yellow colour key to activate Info. Advertisements or information relating to the selected programme are displayed. In some cases all of the information does not fit on the screen. Use the cursor up/down to browse through all the information.
Record Remind Info
BBC1
NEXTVIEW
EM3E
BBC1 CNN TVE
Theme The theme guide displays a list of all programmes at the selected date, that matches with the selected category (news, sport, culture, movies, ...). The default starting item will be the current or next programme on the current TV channel. The THEME selection is only present if programmes in the TV guide have defined themes.
é
Press the yellow colour key again to switch off the information.
Monday 9 Oct Channel Theme
18:03 Overview
Overview The Overview menu provides a list of programmes that are marked as reminders or to be recorded each day. When more than one programme to be recorded has an overlap in time, these programmes will be marked by a red colour.
BBC1
NEXTVIEW
Record Remind Info
BBC1 CNN TVE BBC2
17.10 17.30 18.05 19.00
After the programme has been broadcast, all items set for once will be deleted from the list the following day.This menu can be used to change a reminder or recorder.
3.
Note: the TV will automatically interpret the broadcast time (as shown on the teletext guide) of your selected programme into the correct local time and date.
GB 13
16
NEXTVIEW
NEXTVIEW
17
GB 14 3.
Teletext
B
INSTANT Q
B
Select Picture/NEXTVIEW-Teletext Guide
colour keys to select
yÚ
INSTANT
Q
yÚ
æ
U æ
MENU
U
f
h
æ
b
f b
h
MENU
OK
b
OK key to activate
EM3E
OK
Press the æ key. Press the b key. The screen is divided into two parts: the left side for the normal main picture, the right side for NEXTVIEW/Teletext Guide. Press the b key to return to a full NEXTVIEW/Teletext guide screen, or press the æ key to return to a full picture screen.
MENU
Most TV channels broadcast information via teletext. Each channel which broadcasts teletext transmits a page with information on how to use its teletext system. Look for the teletext page with the main index (usually p. 100). Depending on the TV channel, teletext is transmitted in different systems. The colours used in the options line correspond with the colour keys of your remote control.
V
P
¬
About Easy Text
1
V P
¬
2
3
4
5
6
cursor to select pages
7
8
9
Acquisition and updating of
1 4 7
NEXTVIEW
2 5 8 0
0
b a h
ACTIVE CONTROL
information
3 6 9
i
0
0
X
S
b
b
0 b
i
X S
SMART
SMART
Q
M
a
q
Acquisition and updating of NEXTVIEW is done when you are watching a TV channel supporting NEXTVIEW.
DNR
®
INSTANT
Video recorder restrictions with
NEXTVIEW
X
w
M
q
Easy Text considerably reduces the waiting time (on condition that the teletext broadcast of the particular TV channel is received for at least half a minute) by : · a direct selection of previous and following pages which are in transmission and of the pages referred to in the options line · a habit watcher list: frequently used pages are put automatically in a list of preferred pages, so that they are immediately available · the precapturing of the page numbers referred to in the displayed page · the precapturing of all the subpages.
Directions for use
The Record item and the automatic recording will only be present and possible if your video recorder is equipped with NEXTVIEWLink. Your video recorder should be connected to EXTERNAL 2. See Connect Peripheral Equipment, p. 22.
Switch Teletext on and off
Press b to switch the teletext on or off. The main index page appears on the screen together with two information lines at the top and one option line at the bottom of the screen. Remark: if the displayed teletext characters on screen do not correspond with the characters used in your language, press the X key repeatedly to select Language group 1 or 2.
The daily, weekly and series options, the number of recordings set and the way overlapping recordings are managed, depend on the type of video recorder you have.When all video recorder timers are full, the item Record in the menu will not be present.
Select a Teletext page
With the digit keys Enter the desired page number with the digit keys. The page counter seeks the page or the page appears immediately when the page number has been stored in the memory. A message appears when you have entered a non existent or incorrect page number. Page numbers beginning with 0 or 9 do not exist. Choose another number. With the option line Select with the colour keys, corresponding to the coloured options at the bottom of the screen, the desired subject.
Upload video recorder overview When the TV is switched on, the timer recordings are uploaded to the TV to check if any manual addition or deletions have been done.This is shown in the overview. The video recorder manages and removes timer recordings when performed.
Some NEXTVIEWLink video recorders do not allow a daily programming of the recording to start on a Saturday or Sunday. In this case the item daily will be removed from the menu on those days.
Select Picture/Teletext
Select a TV channel which broadcasts teletext. Press the b key. The screen is divided into two parts: the left side for the normal main picture, the right side for teletext broadcast by the selected TV channel. Press the b key to return to a full screen picture or press the b key to return to a full teletext picture.
Quickly run through the teletext pages
Press the cursor up/down or the - P + key to run through the previous or the following pages.
Select the previously selected teletext page
Press the 0 key.
18
NEXTVIEW
Teletext
19
Select the index teletext page
Select Continuous Subtitles
B
Press the white colour key to display the main index (usually p.100).
INSTANT
Q
®
Ò
U
yÚ
TV channels with teletext often transmit programmes with subtitling. For each TV channel you can store a subtitle page which will be displayed continuously if the programme being broadcast is transmitted with subtitles.
U
f
h
æ
b
MENU
OK
MENU
OK to activate
cursor to select subpages
Switch on teletext and select the proper subtitle page from the index. Switch off teletext. Now the subtitle page is stored for the selected TV channel.
V
P
¬
Only for T.O.P teletext broadcasts : T.O.P orders the pages in categories and adds other possibilities of enhancing ease of use. Press i. A T.O.P. overview of the teletext subjects available is displayed. Not all TV channels broadcast T.O.P. teletext.When the teletext system is not T.O.P. teletext, a message appears at the top of the screen. Select with the cursor up/down, left/right the desired subject and press the OK key.
1
2
3
4
5
6
Select subpages
i
7
8
9
Once subtitles have been stored and Subtitle On has been selected they will automatically be displayed on the selected TV channel if subtitles are in the transmission. Select Subtitle On or Off in the Features menu, see p. 13. The subtitle symbol j appears when Subtitle On is selected. Remark: you are in teletext mode, so only teletext functions are available.
i
0
0
X
S
b
SMART
w
M
a
q
h
When a selected teletext page consists of different subpages, one of the subpages appears on the screen. The coloured number in the first information line refers to the displayed subpage. The other subpages can be selected in 2 ways :
ACTIVE CONTROL
P M V
With the cursor left/right The other subpage numbers appear in white as soon as the transmission has found them.They are stored in the memory so that they are available while the teletext page is on screen. Select with the cursor left/right the previous or the following subpage.
Keys on top of the TV
Should your remote control be lost or broken you can still change some of the basic picture settings with the keys on top of the TV. Press the M key repeatedly to select Volume, Brightness, Colour, Contrast. Press the P - or + keys to carry out the selected adjustment. When the menu adjustment is not displayed, the P- or + keys enable you to select the TV channels, the V - or + keys to adjust the volume. The selected adjustment automatically switches off when no action has been executed for 10 seconds.
Directions for use
With the U key · Enter the subpage number yourself: Press U. Enter the desired subpage with the digit keys : e.g. 3 for the third page of seven subpages. The TV searches for the selected subpage.
B
· Automatically rotating subpages: Press U again to cancel the entered digit key for the subpage. Now the subpages rotate automatically.
INSTANT
Q
®
Ò
Press U again to select the subpages with the cursor left/right again.
yÚ
U
f
h
f h
æ
b
MENU
OK
Special teletext functions
V
P
EM3E
¬
1
2
3
Hold Press S to stop the automatically rotating of the subpages or to stop the page counter from seeking when you have entered a wrong page number or when the page is not available. Enter another page number.
4
5
6
7
8
9
i
0
0
S
Enlarge Press h repeatedly to display the upper part, the lower part and then to return to the normal page size.When the upper part is displayed, you can scroll the text, line by line using the cursor up/down.
X
S
b
SMART
w
M
a
q
h
3.
ACTIVE CONTROL
Reveal Press f to reveal/conceal the hidden information, such as solutions to riddles and puzzles.
GB 15
20
Teletext
Teletext
21
GB 16 3.
Connect Peripheral Equipment
Camera & camcorder
Connect your camera or camcorder to sockets at the right side of your TV. Connect the equipment to VIDEO 2 and AUDIO L 3 for mono equipment. For stereo equipment also connect AUDIO R 3. S-VHS quality with an S-VHS camcorder is obtained by connecting the S-VHS cables with the S-VIDEO input 1 and AUDIO inputs 3.
AUD VIDEO S·VI DEO IO
There is a wide range of audio and video equipment that can be connected to your TV.The following connection diagrams show you how to connect them.
& é "
1 2 3
EM3E
Video recorder
Connect the aerial cables 1, 2 and, to obtain the optimum picture quality, eurocable 3 as shown opposite.
If your video recorder is provided with the EasyLink function, the eurocable supplied with it should be connected to EXTERNAL 2 to benefit from the EasyLink functionality.
CABLE
If the eurocable 3 is not used the following steps are required:
EXTERNAL
Digital equipment (DVD, digital satellite tuner,...)
1/2/3
Search for and store the test signal of the video recorder
2
Unplug the aerial cable 1 from the aerial socket x of your video recorder.
EXT.
1 1
& é
Switch on your TV and put the video recorder on the test signal. (See the handbook for your video recorder.)
Connect your digital equipment with a eurocable 1 to one of the euroconnectors (EXT1, EXT2 or EXT3), or with a cinch cable to the VIDEO input at the right side of the TV (see illustration above).
2
"
3
Search for the test signal of your video recorder in the same way as you searched for and stored the TV signals. See Installation, Searching for and storing TV channels, Manual installation, p. 5.
Note: the low quality of some digital picture material may be the cause of digital image distortion. In this case select Eco under the SMART PICTURE a key on the remote control as this setting is intended to improve distorted picture quality.
4
DVD
Directions for use
` (
Store the test signal under programme number 0 or between 90 and 99.
VCR 1
Replace the aerial cable in the aerial socket x of your video recorder after you have stored the test signal.
Headphone
L
Decoder and video recorder Connect a eurocable 4 to your decoder and to the special euroconnector of your video recorder. See also the video recorder handbook. See Define Decoder/Descrambler prog. numbers, p. 7. You can also connect your decoder directly to EXTERNAL 1 or 2 with a eurocable.
& é
Insert the plug into the headphone socket L at the right side of the TV. Press ¬ on the remote control to switch off the internal loudspeakers of the TV. The headphone impedance must be between 8 and 4000 Ohm. The headphone socket has a 3.5 mm jack. In the SOUND menu select Headphone volume to adjust the headphone volume, see p. 12.
Video recorder and other peripherals (except Digital Sources)
&
CABLE
Connect the aerial cables 1, 2 and 3 as shown opposite. Better picture quality can be obtained if you also connect eurocable 5 to EXTERNAL 2 and a eurocable 4 to EXTERNAL 1 or EXTERNAL 3.
é
Audio equipment / Amplifier
Connect the audio cables to the audio input of your audio equipment and to AUDIO L and R at the back of your TV.
AUDIO
EXTERNAL
Look for the test signal of your peripheral in the same way as you do for a video recorder.
1 2
1
3
4
5
2
When a video recorder is connected to EXTERNAL 1 you can only record a programme from your TV. Only when a video recorder is connected to EXTERNAL 2 it is possible to record a programme from your TV as well as from other connected equipment. See Record with your video recorder, p. 26.
You can listen to your TV sound via your audio equipment.
Note: EXTERNAL 1 can handle CVBS and RGB, EXTERNAL 2 CVBS and Y/C and RGB, EXTERNAL 3 only CVBS.
If you want to connect more equipment to your TV, consult your dealer.
VCR 1
22
Connect Peripheral Equipment
Connect Peripheral Equipment
23
To select connected equipment
Satellite receiver Press the OK key simultaneously with the digit key 1. Now you can operate your satellite receiver with the remote control of your TV.
If the TV is connected to a video recorder with the EasyLink function, in some cases the TV will be switched on, even when it was in standby. (E.g. playback tape,...) This is not possible when Child lock On is selected.
B
INSTANT Q
7
®
yÚ
8
Ò
9
i
U
æ
MENU
0
f b h
0
Equipment connected with an aerial cable only : Select the programme number under which you have stored the test signal with the digit keys.
MENU
Keep the MODE key on the left side of the remote control pressed and simultaneously press: to switch the
SAT
X
S
b
SMART
w
M
a
q
OK
Ò
b
menu on or off
h
MENU
w
V P
¬
ACTIVE CONTROL
Equipment connected to a euroconnector or to the right side of the TV Press the w key repeatedly to select EXT1, EXT2, EXT3 or FRONT, according to where you connected your equipment at the back or the right side of your TV. Remark : Most equipment (decoder, video recorder, satellite receiver) carries out the switching itself.
1 4 7
These keys function with equipment which use the RC5 signalling standard.
2 5 8 0
0
b a
DNR
3 6 9
DVD player Press the OK simultaneously with the digit key 2. Now you can operate your DVD player with the remote control of your TV. Keep the MODE key on the left side of the remote control pressed and simultaneously press:
MENU
If you want to change to TV channels? Enter the programme number of the TV channel which you want to watch with the digit keys or press the w key repeatedly to select TV.
i
X S
SMART
B
w
X
M h
ACTIVE CONTROL
0
to switch the DVD menu on or off b 0 X Ò 0-9 OK to select a DVD title to select a DVD chapter to select your choice of audio language to search down stop play to search forward to select a programme number from your DVD to enter the selected menu item
q
B
Audio and video equipment keys
INSTANT
Q
®
Ò
yÚ
U
f
h
æ
b
Most of the audio and video equipment from our range of products can be operated with the remote control of your TV.
MENU
OK
® Ò
for record, for rewind, for stop, for play, for fast forward, for selecting 1- or 2-digit programme numbers from the video recorder, for sequential programme selection from the video recorder tuner, to select a programme number from your video recorder tuner, to switch the video recorder to standby
Video recorder Keep the VCR key on the left side of the remote control pressed and simultaneously press:
V
P
¬
®
1
2
3
Ò
Directions for use
4
5
6
7
8
9
i
0
0
®, C, f, h, w have no function
X
S
b
SMART
w
M
a
q
DNR
h
Note: after replacing the batteries the default operational equipment is the satellite receiver.
ACTIVE CONTROL
- P+
0 to 9
EM3E
B
These keys function with equipment which use the RC6 signalling standard.
These keys function with equipment which use the RC5 signalling standard.
If your video recorder has the EasyLink function, the key INSTANT ® for recording, can be operated in the TV mode. If your EasyLink video recorder has the system standby function, when you press the B key for 3 seconds, both TV and the video recorder are switched to standby.
3.
GB 17
24
Connect Peripheral Equipment
Connect Peripheral Equipment
25
GB 18 3.
Record with your video recorder
Care of the screen Clean the TV with a slightly damp soft cloth. Do not use abrasive solvent as it can damage the TV screen. Check with your dealer or call a TV technician.
Tips
To record S-VHS quality, connect an S-VHS peripheral directly to the video recorder.
EM3E
& é
Record a TV programme Select the programme number on your video recorder.
Set your video recorder to record. See the handbook for your video recorder.
Switching programme numbers on your TV does not disturb recording ! No sound · No sound on any channel? Check the volume isn't at minimum. · Is the sound interrupted with the mute key ¬?
No picture · Is the aerial connected properly? · Are the plugs tightly connected in the aerial socket? · Is the aerial cable in good condition and does it have suitable plugs? · Are the connection facilities to a possible second TV in good condition? If in doubt, consult your dealer.
Record a programme on your video recorder connected to EXTERNAL 2 from Audio/Video equipment connected to EXTERNAL 1, EXTERNAL 3 or to sockets on the right side of the TV Switch on the equipment.
End of life directives Philips is paying a lot of attention to produce environmentally-friendly in green focal areas.Your new TV contains materials which can be recycled and reused. At the end of its life specialised companies can dismantle the discarded TV to concentrate the reusable materials and to minimise the amount of materials to be disposed of. Please ensure you dispose of your old TV according to local regulations.
& é "
Remote control If your TV no longer responds to the remote control, the batteries may be dead. You can still use the M key and the -/+ keys at the top of your TV.
Select the right external on your video recorder.
Set your video recorder to record. You record what you are watching on the screen.
Do not switch programme numbers or do not switch off your TV when you are recording !
How to dispose of batteries? The batteries supplied do not contain the heavy metals mercury and cadmium. Nevertheless in many countries batteries may not be disposed of with your household waste. Please ensure you dispose of batteries according to local regulations.
Directions for use
Record with your video recorder with EasyLink
If you have connected an S-VHS video recorder provided with the EasyLink function, you can record S-VHS-quality from an S-VHS peripheral connected to the right side of the TV. (E.g. from an S-VHS camcorder.)
Poor Picture · Have you selected the correct TV system? · Is your TV or house aerial located too close to loudspeakers, non-earthed audio equipment or neon lights, etc.? · Mountains or high buildings can cause double pictures or ghost images. Sometimes you can improve the picture quality by changing the direction of the aerial. · Is the picture or teletext unrecognisable? Check if you have entered the correct frequency. See Installation, p. 5. · Are brightness and contrast out of adjustment? Select Factory settings in the Setup menu, p. 7. · Sometimes poor picture quality is possible when having activated an S-VHS camera or camcorder connected to the right side of your TV and another peripheral is connected to EXT1 or EXT2 at the same time. In this case switch off one of the other peripherals. Menu Have you selected the wrong menu? Press the MENU key again to exit from the menu. No solution Switch your TV off and then on again once. Never attempt to repair a defective TV yourself.
INSTANT
B
INSTANT
Q
®
Index
®
Ò
yÚ
U
f
h
æ
b
In TV mode, it is possible to start a direct recording of the programme which is being displayed on the TV screen. Press the INSTANT ® record key of the remote control. The video recorder switches on from standby and a message of what is being recorded appears on the screen. The video recorder starts recording the programme you are watching. Switching programme numbers on your TV does not disturb recording !
MENU
OK
V
P
¬
When recording a programme from a peripheral connected to EXTERNAL 1, 3 or FRONT, you can not select another TV programme on the screen. To watch TV programmes again, press the programme number you want to select twice. Attention: the recording is stopped and your video recorder switches to standby.
Record with your video recorder with
NEXTVIEWLink
If your video recorder is equipped with NEXTVIEWLink, and you tagged one or more programmes to be recorded automatically in the NEXTVIEW mode, it is not necessary for the TV to be in the standby mode or switched on for the recording to start.
a ACI, 5 active control, 10 automatic installation, 5 auto format, 7 auto surround, 8 AVL, 12 b bilingual broadcast, 10 c camcorder, 23 child lock, 13 continuous subtitles, 21 country, 4 d decoder/descrambler, 7 delta volume, 12 digital options, 11 double lines, 11 dual screen, 14 DVD, 25 dynamic contrast, 11 e easy text, 19 eurocable, 22 f factory settings, 7 favourite programmes, 6
freeze, 10 frequency, 5 g give name, 6 graphic equalizer,