Text preview for : KVT-M700 instructions.pdf part of Kenwood kvt-m700 Kenwood kvt-m700 user manual
Back to : KVT-M700 instructions.pdf | Home
7-Inch WIDE SCREEN MONITOR-RECEIVER
KVT-M700
INSTRUCTION MANUAL
© PRINTED IN JAPAN B64-2138-00/01 (E/DT)
Contents
Before Use .............................................................4
· Safety Precautions · About RDS · Navigation Announcement [NAV INTERRUPTION] · Sound Attenuate [NAV GUIDE] · Exit the System Setup Screen
Monitor Control Function.....................................5
· Opening the Monitor · Closing the Monitor · Power Off · Switching the Monitor's Picture · Switching the TV/Video Screen Mode · Switching the AV Output · Switching to the Angle/Screen Control Screen · Turning the Monitor Picture Off Angle Control Screen · Adjusting the Angle Position [ANGLE] · Adjusting the Slide Position [SLIDE] · Automatic Open/Close [AUTO OPEN-CLOSE] · Switching to the Screen Control Screen · Exit the Angle Control Screen Screen Control Screen · Adjusting the Picture Quality · Auto Dimmer [DIM] · Switching to the Angle Control Screen · Exit the Screen Control Screen
Tuner Setting Function.......................................14
Tuner Setting Menu Screen · Selecting the RDS Setting Screen · Selecting the TV Area Setting Screen · Selecting the DAB Tuner Setting Screen RDS Setting Screen · News Bulletin with PTY News Timeout Setting [NEWS] · Alternative Frequency Function [AF] · Region Restrict Function [REG] · Auto TP Seek Function [ATPS] · Exit the RDS Setting Screen TV Area Setting Screen · Setting the TV Area · Exit the TV Area Setting Screen
Sound Control Function .....................................16
Sound Control Menu Screen · Selecting the Audio Setting Screen · Selecting the System Es Setting Screen · Selecting the Speaker Select Screen · Selecting the Tone Control Screen Audio Setting Screen · Balance and Fader [BAL/FAD] · Loudness [LOUD] · B.M.S. (Bass Management System) [AMP BASS] · B.M.S. Frequency Offset [AMP FREQ] · Volume Offset · Switching the Audio Setting Screen -1 and 2 · System Q [SYSTEM Q] · System Q Ex On & Off [SYSTEM QEx] · Dual Zone System [2 ZONE] · Exit the Audio Setting Screen Speaker Select Screen · Speaker & Woofer Setting · Exit the Speaker Select Screen Tone Control Screen · Tone Control (System QEx set to OFF) · Tone Control (System QEx set to ON) · Switching the Tone Control Screen -1 and 2 · Exit the Tone Control Screen System Es Setting Screen · System Es · Exit the System Es Setting Screen
Menu Function ......................................................8
Menu Screen · Selecting the Menu Screen · Selecting the Setup Menu Screen · Selecting the Sound Control Menu Screen · Selecting the Tuner Setting Menu Screen · Selecting the External Display Control Screen · Selecting the Sensor Box Control Screen · Exit the Menu Screen
Setup Function ......................................................9
Setup Menu Screen · Selecting the Touch Panel Adjustment Screen · Selecting the AV Setup Screen · Selecting the Clock Adjustment Screen · Selecting the System Setup Screen · Selecting the Code Security Screen Clock Adjustment Screen · Synchronize Clock [SYNC] · Manual Clock Adjustment [CLOCK] · Exit the Clock Adjustment Screen Code Security Screen · Mask Key · Exit the Code Security Screen Touch Panel Adjustment Screen · Adjusting the Touch Position AV Setup Screen · Setting the AV IN-1 Mode [AV-IN1] · Setting the AV IN-2 Mode [AV-IN2] · Setting the RGB Mode [RGB-IN] · Setting the AV Output Mode [AV OUT] · Exit the AV Setup Screen
Source Control Function (Common opreation) ..........................................20
· Displaying the On Screen Control · Changing the Audio Source Mode · Volume · Attenuator · Loudness · Non-fading Output · Switching to the Menu Screen · Changing the Function Buttons · Changing the Background Mode for the Control Screen · TEL Mute
System Setup Function ......................................12
System Setup Screen · Touch Sensor Tone [BEEP] · On Screen Display [ON SCREEN] · Disabled System Indicator [DSI] · Switching the Setup Screen -1 and 2 · Selectable Illumination [KEY ILLUMI] · Key Indicator Color [KEY INDICATOR]
2
FM/AM Tuner Control Function ........................22
· Selecting the FM Band · Selecting the AM Band · Tuning · Station Preset Memory · Preset Tuning · Auto Memory Entry · Seek Mode · Monaural Reception · Local Seek · Traffic Information · Presetting Volume for Traffic Information · Switching Display · Switching to the FM/AM List Screen · Switching to the PTY Search Screen · FM/AM List Screen · PTY Search Screen
Other Option Control Function ..........................31
DAB Tuner Control DAB Tuner Setting Screen · Automatic Switching DAB priority [DAB PRIORITY] · Dynamic Range Control [DRC] · Regional Announcement Function [REG INTRUPT] · Switching the DAB Tuner Setup Screen -1 and 2 · Announcement select mode · Exit the DAB Tuner Setting Screen Control Screen · Switching the Pre-set band · DAB Reception · Service Preset Memory · Traffic Announcement Function · Auto Ensemble Memory Entry · Switching the Service component · Seek Mode · Presetting Volume for Announcement · Switching Display · Switching to the DAB PTY Search Screen · Switching to the Language Filter Screen · DAB PTY Search Screen · Language Filter Screen External Display Control · Switching the Display · Exit the External Display Control Screen Sensor Box Control · Setting the Menu · Exit the Sensor Box Control Screen
AV Control Function ...........................................25
· Selecting the On Screen Control · Selecting the Preset Band TV1 and TV2 · Selecting the Video Input · Seek Mode · Selecting the Channel · Station Preset Memory · Auto Memory Entry · Recalling a Preset Station · Switching to the TV List Screen · Switching to the Name Set Screen · TV List Screen
CD Player Control Function ................................27
· Pause and play · Fast Forwarding and Reversing · Track Search · Track Repeat · Track Scan · Random Play · Switching Display · Switching to the Name Set Screen
Remote Control Function ...................................36 Installation ...........................................................38 Troubleshooting Guide.......................................45 Specifications ......................................................48
Disc Changer Control Function ..........................28
· Pause and play · Fast Forwarding and Reversing · Track Search · Album Search · Track Repeat · Album Repeat · Track Scan · Random Play · Magazine Random Play · Switching Display · Switching to the Disc List Screen · Switching to the Name Set Screen · Disc List Screen
Name Set Function .............................................30
Station Name Preset (SNPS)/ Disc Name Preset (DNPS)
The illustrations of the display and the panel appearing in this manual are examples used to explain more clearly how the controls are used. Therefore, what appears on the display in the illustrations may differ from what appears on the display on the actual equipment, and some of the illustrations on the display may represent something impossible in actual operation.
3
Before Use
Safety Precautions
2WARNING
Mask key
If you have transmitted the Mask Key's signal once to the unit in advance, you will have to transmit it once again if the unit has been removed from the battery.
2 CAUTION
To prevent injury and/or fire, take the following precautions:
· Ensure that the unit is securely installed. Otherwise it may fly out of place during collisions and other jolts. · When extending the ignition, battery or ground wires, make sure to use automotive-grade wires or other cables with an area of 0.75mm2 (AWG18) or more to prevent wire deterioration and damage to the wire coating. · To prevent short circuits, never put or leave any metallic objects (e.g., coins or metal tools) inside the unit. · If the unit starts to emit smoke or strange smells, turn off the power immediately and consult your Kenwood dealer. · Do not touch the liquid crystal fluid if the LCD is damaged or broken due to shock. The liquid crystal fluid may be dangerous to your health or even fatal. If the liquid crystal fluid from the LCD contacts your body or clothing, wash it off with soap immediately.
2CAUTION
Do not loose the "Mask Key". If power is disconnected from the unit, correct operation can only be restored by the "Mask Key's" signal. The "Mask Key" will also be required for service repair.
NOTE
If you send products in for repair that include a mask key, make sure to present the unit together with the mask key.
Screen brightness during low temperatures
When the temperature of the unit falls such as during winter, the liquid crystal panel's screen will become darker than usual. Normal brightness will return after using the monitor for a while.
To prevent damage to the machine, take the following precautions:
· Make sure to ground the unit to a negative 12V DC power supply. · Do not open the top or bottom covers of the unit. · Do not install the unit in a spot exposed to direct sunlight or excessive heat or humidity. Also avoid places with too much dust or the possibility of water splashing. · Do not subject the faceplate to excessive shock, as it is a piece of precision equipment. · When replacing a fuse, only use a new one with the prescribed rating. Using a fuse with the wrong rating may cause your unit to malfunction. · To prevent short circuits when replacing a fuse, first disconnect the wiring harness. · Do not use any screws except for the ones provided. The use of improper screws might result in damage to the main unit. · You cannot view video pictures whilst the vehicle is moving. To enjoy TV/video pictures, find a safe place to park and engage the parking brake.
NOTE
IMPORTANT INFORMATION About the disc changer/CD player to be connected:
To connect a disc changer having the "O-N" switch to this unit, set the "O-N" switch to "N". To connect a disc changer having no "O-N" switch to this unit, the converter cord CA-DS100 and/or switching adapter KCA-S210A are required as options. A disc changer doesn't work when it is connected without using these options. If a model with no "O-N" switch is connected, some unavailable functions and information that cannot be displayed are generated. Note that none of the KDC-C100, KDC-C302, C205, C705, and non-Kenwood CD changers can be connected..
You can damage both your unit and the CD changer if you connect them incorrectly.
About RDS
RDS (Radio Data System)
When listening to an RDS station, the programme service name of the station is displayed, advising you quickly which station is being received. RDS (Radio Data System) stations also transmit frequency data for the same station. When you are making long trips, this function automatically alternative switches to the particular frequency with the best reception for the particular network of stations that you want to listen to. The data is automatically stored, allowing you to switch quickly to another RDS stations, broadcasting the same programme, that has better reception. These include stations stored in the station preset memory that you often listen to.
· If you experience problems during installation, consult your Kenwood dealer. · If the unit does not seem to be working right, try pressing the reset button first. If that does not solve the problem, consult your Kenwood dealer.
Enhanced Other Network
Stations that offer also transmit information about other RDS stations that have traffic information. When you are tuned to a station that is not transmitting traffic information, but another RDS station starts transmitting a traffic bulletin, the tuner automatically switches to the other station for the duration of the bulletin.
Reset button Cleaning the Unit
If the faceplate of this unit is stained, wipe it with a dry soft cloth such as a silicon cloth. If the faceplate is stained badly, wipe the stain off with a cloth moistened with neutral cleaner, then wipe neutral detergent off.
2CAUTION
Alarm
When an emergency transmission (announcing disasters, etc.) is sent, all current functions are interrupted to allow the warning to be received.
Applying spray cleaner directly to the unit may affect its mechanical parts. Wiping the faceplate with a hard cloth or using a volatile liquid such as thinner or alcohol may scratch the surface or erases characters.
4
Monitor Control Function
Opening the Monitor
1 Set the vehicle's parking brake. 2 Press the [OPEN] button. The monitor will open.
· The gear shift lever or other parts may interfere with the monitor when it opens. If so, move the gear shift lever (being sure to do so safely) before operating the set. (The monitor is drawn back in automatically if it cannot be opened normally due to an obstacle.) · The monitor cannot be opened unless the parking brake is set. · The position to which the monitor slides or angle when the power is turned on can be set. (Refer to the angle control screen on (Page 7).
OPEN
Closing the Monitor
Press the [OPEN] button. The monitor will close.
·The monitor cannot be closed unless the parking brake is set. · Make sure not to get your fingers caught between
the faceplate and the unit.
Power Off
Press the [SRC] button for at least 1 second. Power On Press the [SRC] button.
Switching the Monitor's Picture
FNC V.SEL SRC MODE OPEN
Press the [V.SEL] button. Each time the button is pressed the monitor's picture switches as follows: During the KTC-V500E is not connected: Display Picture "VD 1" Video 1 (AV IN1 setting during "VD") "VD 2" Video 2 (AV IN2 setting during "VD") "NAV" RGB (from I/F terminal: RGB setting during "ON") During the KTC-V500E is connected: Display Picture "VD 1" Video 1 (AV-IN1 setting during "VD") "VD 2" Video 2 (AV IN2 setting during "VD") "NAV" RGB (from I/F terminal: RGB setting during "ON") "ch" Television
· For "AV IN" and "RGB" setting, refer to . (Page 11). · The "NAV", "VD 1" and "VD 2" displays can be changed by the . You cannot view television and video pictures whilst the vehicle is moving. To enjoy television and video pictures, find a safe place to park and engage the parking brake.
5
Monitor Control Function
Switching the TV/Video Screen Mode
Press the [MODE] button. Each time the button is pressed the screen mode switches as follows: Display Setting "FULL" Full screen mode "ZOOM" Zoom screen mode "JUST" Just screen mode "CINEMA" Cinema screen mode "NORMAL" Normal screen mode
You cannot operate when the navigation picture is displayed.
Switching the AV Output
Press the [V.SEL] button for at least 1 second. Each time the button is pressed for at least 1 second the AV output switches as follows: Display Setting "VIDEO1" Picture/sound input from the AV IN 1 terminal "VIDEO2" Picture/sound input from the AV IN 2 terminal "TV" Picture/sound of the television (During the KTC-V500E is connected)
FNC V.SEL MODE
SCREEN
yyy ;;;;;; yyy ;;;;;; yyyy ;;;;
· JUST · ZOOM · CINEMA
yyyyyy ;;;;;; yyyyyy ;;;;;;
Screen Mode
· FULL · NORMAL
Switching to the Angle/Screen Control Screen
Press the [SCREEN] button. ( Page 7)
Turning the Monitor Picture Off
Press the [SCREEN] button for at least 1 second.
The picture reappears when the one of the SCREEN, MODE, V.SEL or FNC buttons is pressed.
yyyy ;;;;
6
Angle Control Screen
A NG L E C T R L S C R E E N A NG L E
Screen Control Screen
S C R E E N B R T T I N ON D I M OFF C T R L A NG L E
S L I D E
CO L CON T
A U T O O P E N - C L O S E O N O F F O K
B L K D I M O K
Adjusting the Angle Position [ANGLE]
The monitor slants back one step: Touch the [3] button. The monitor slants forward one step: Touch the [2] button.
Adjusting the Picture Quality
Item BRT TIN COL CONT Touch [3] [2] [3] [2] [3] [2] [3] [2] [3] [2] [3] [2] Setting Brighter screen Darker screen Stronger green level Stronger red level Deeper color Paler color Stronger contrast Less contrast Less black level Stronger black level Brighter screen Darker screen
· The angle can be adjusted in 9 steps. · The next time the monitor is opened it stops at the set location. · When the Monitor slide position is set toward the back, the Angle position can't be set more than 90 degrees toward the back.
BLK DIM
Adjusting the Slide Position [SLIDE]
The monitor to the front: Touch the [3] button. The monitor to the back: Touch the [2] button.
· The [ TIN ] and [ COL ] cannot be adjusted for the navigation picture or the control screen. · The [ TIN ] cannot be adjusted for the picture of PAL/ SECAM. · Separate picture quality settings can be stored for the television, video, control screens and navigation screens.
Auto Dimmer [DIM]
Touch [7ON] Setting The [DIM] level can be adjusted. Also, when the area around the monitor dark it's at the brightness level set by the [DIM]. The [DIM] items can't be adjusted. Also, even if the area around the monitor is dark, it can't be changed from the brightness set by [BRT].
· The next time the monitor is opened it stops at the set location. · When the Angle position is set more than 90 degrees toward the back, the Monitor slide position can't be set toward the back.
[7OFF]
Switching to the Angle Control Screen Automatic Open/Close [AUTO OPEN-CLOSE]
Touch [7ON] [7OFF] Setting Switch the ACC on/off to open/close the monitor Use the OPEN button to open/close the monitor Touch the [ANGLE] button.
Exit the Screen Control Screen
Touch the [OK] button.
If the shift lever or other parts of the vehicle interfere with the monitor when it opens, select "OFF".
Switching to the Screen Control Screen
Touch the [SCREEN] button.
Exit the Angle Control Screen
Touch the [OK] button.
7
Menu Function
On Screen Control Menu Screen
ME NU SOUND SETUP AV 1 2:0 0 TUNER I / F
T OUCH C L OC K
SRC AM FM3 P 1 1 0 8 . 5 FM - I NFO P 1 P 2 P 3 P 4 P 5 FM M Hz P 6
S Y S T EM
COD E EXT SOURC E SENS
Selecting the Menu Screen 1 Displaying the On Screen Control
FNC
Press the [FNC] button to display the on screen control.
Control Screen
T I ME NU TUNER FM3 P 1 FM - I NFO ATT AM INFO P 1 P 2 P 3 P 4 P 5 LOUD LIST FM PTY P 6 9 2 . 5 M Hz 1 2:0 0
If you make no button operation for 10 seconds, the on screen control is automatically cancelled.
2 Selecting the Control Screen
When the [FNC] button is pressed during on screen control display, it switches to control screen.
3 Selecting the Menu Screen
Touch the [MENU] button to switch the menu screen.
Selecting the Setup Menu Screen
Touch the [SETUP] button. ( Page 9)
Selecting the Sound Control Menu Screen
Touch the [SOUND] button. ( Page 16)
Selecting the Tuner Setting Menu Screen
Touch the [TUNER] button. ( Page 14)
Selecting the External Display Control Screen
Touch the [EXT] button. ( Page 35)
Selecting the Sensor Box Control Screen
Touch the [SENS] button. ( Page 35)
Exit the Menu Screen
Touch the [SOURCE] button. Return to source control screen.
8
Setup Function
Setup Menu Screen
ME NU SOUND SETUP AV 1 2:0 0 TUNER I / F 1 2 : 0 0 R E S E T
Clock Adjustment Screen
C L O C K
T OUCH C L OC K COD E
S Y S T EM S Y N C O C L OC K N OF F AD J UST RTN
SOURC E
Selecting the Touch Panel Adjustment Screen
Touch the [TOUCH] button. ( Page 10)
Synchronize Clock [SYNC]
Synchronizing the RDS station time data and this unit's clock. Touch [7ON] [7OFF] Setting Synchronizes the time. Adjust the time manually.
Selecting the AV Setup Screen
Touch the [AV I/F] button. ( Page 11)
It takes 3 to 4 minutes to synchronize the clock.
Selecting the Clock Adjustment Screen
Touch the [CLOCK] button. ( Page 9)
Manual Clock Adjustment [CLOCK]
To advance the hours. To advance the minutes.
Selecting the System Setup Screen
Touch the [SYSTEM] button. ( Page 12)
C L O C K 1 2 : 0 0
Selecting the Code Security Screen
Press the [CODE] button for at least 2 seconds. ( Page 10) To make the hours go back.
To make the minutes go back.
Setting the Minutes to "00" Touch the [RESET] button.
· Touch the [RESET] button while the minute is below "30" rounds it off, and while the minute is "30" or more rounds it up. · This adjustment can be done when the is set as OFF.
Exit the Clock Adjustment Screen
Touch the [RTN] button. Return to the setup menu screen.
9
Setup Function
Code Security Screen Touch Panel Adjustment Screen
T O U C H T h e s y s t em i s n ow wa i t i n g f o r y o u r MA S K KEY s i g n a l . P l e a s e i n p u t n ow . P t t R l h h i
P A N E L T t t o o u c e r o n p C
A D J U S T h o f i n t h e o r n e r .
e a s e e Ce n e B u t g h t - T
C A N C E L SECUR I T Y RTN
R E S E T
Mask Key
Because authorization by the Mask Key is required when it's removed from the vehicle, personalizing this unit by using the Mask Key is a help in preventing theft.
Adjusting the Touch Position
The touch panel can be adjusted if the position touched and the operation performed do not match.
1 Enter the Mask Key's signal
Hold down the transmit button on the Mask key until the full transmit level indicator lights up in the display."Checking." is displayed.
1 Accurately touch the mark at the upper right. 2 Accurately touch the mark at the lower left.
When the mark at the lower left is touched, the adjustment is completed and the system setup menu screen reappears.
· If the [CANCEL] button is touched without touching the button at the upper right, the adjustment is canceled and the screen that was set before switching to the system setup menu reappears. · If the [CANCEL] button is touched after touching the button at the upper right, the button at the upper right reappears. · If the [RESET] button is touched, the settings are reset to the factory defaults and the setup menu screen reappears.
Transmission part Transmit button
Keep the Mask Key close to the signal sensor when you transmit the Mask Key's signal.
2 Reenter the Mask Key's signal
Hold down the transmit button on the Mask Key until the full transmit level indicator lights up in the display. Return to the setup menu screen. Press the Reset button and when it's removed from the battery power source 1 Turn the power ON The vehicle engine turns ON. "The system is now waiting for your MASK KEY signal. Please input now." is displayed.
2
Enter the Mask Key's signal Repeat steps 4 and 5 abobe, and enter the Mask Key's signal. The "ALL OFF" screen is displayed. The unit can be used.
Exit the Code Security Screen
Touch the [RTN] button. Return to the setup menu screen.
10
AV Setup Screen
A V - I N 1 VD A V - I N 2 VD NAV AUTO VD OF F VD R G B - I N ON OF F A V - O U T AV 1 AV I / F AV 2 T 2 1
NAV V RTN
Setting the AV IN-1 Mode [AV-IN1]
Touch [7NAV] Setting It becomes the navigation mode setting. Operate the V.SEL button when the image from the navigation unit connected to AV IN1 terminal is shown on the monitor. It becomes the video mode setting.Operate the V.SEL button when the image from the device connected to AV IN1 terminal is shown on the monitor.
Setting the RGB Mode [RGB-IN]
Touch [7ON] Setting It becomes the RGB mode setting. Operate the V.SEL button when the image from the the navigation unit connected to I/F terminal is shown on the monitor. It becomes the OFF mode setting.Use this setting when there's nothing connected to the I/F terminal.
[7VD]
[7OFF]
Select the AV-IN1 input display: Selecting the display when this device is switched to internal AV-IN1 terminal input source. Each time you touch the [ 2 ] or [ 3 ] button, the display switches as follows: "VD 1""VIDEO1" "NAV1""DVD1" "VCR1" "VCD1""GAME1""AUX1"
Select the I/F input display: Selecting the display when this device is switched to internal I/F terminal input source. Each time you touch the [ 2 ] or [ 3 ] button, the display switches as follows: "NAV" "DVD""DVB" "RGB"
Setting the AV Output Mode [AV-OUT]
Touch [7AV1] [7AV2] [7TV] Setting Picture/sound from AV IN1 terminal. Picture/sound from AV IN2 terminal. Picture/sound from television. (During the KTC-V500E is connected)
Setting the AV IN-2 Mode [AV-IN2]
Touch [7VD] Setting It becomes the video mode setting. Operate the V.SEL button when the image from the device connected to AV IN2 terminal is shown on the monitor. It becomes the auto video mode setting. When the video signal input to the AV IN2 terminal, the monitor image is switched to the image of the device connected to the AV IN2 terminal. It becomes the OFF mode setting.Use this setting when there's nothing connected to the AV IN2 terminal.
[7AUTO]
Exit the AV Setup Screen
Touch the [RTN] button. Return to the setup menu screen.
[7OFF]
Select the AV-IN2 input display: Selecting the display when this device is switched to internal AV-IN2 terminal input source. Each time you touch the [ 2 ] or [ 3 ] button, the display switches as follows: "VD 2""VIDEO2" "NAV2""DVD2" "VCR2" "VCD2""GAME2""AUX2""CAMERA"
11
System Setup Function
System Setup Screen-1
B E E P O A U T O O D S I O N OF F RTN N A V K E Y K E Y N A V O
System Setup Screen-2
I L L UM I GR E E N
N O N N
OF F S C R E E N OF F
RED
I N D I C A T O R SOURC E I N T E R R U P T I O N N OF F
G U I D E SOUND AT T RTN
S Y S T EM
S Y S T EM
Touch Sensor Tone [BEEP]
Setting the operation check sound (beep sound) ON/OFF. Touch [7ON] [7OFF] Setting Touch sensor tone is turned on Touch sensor tone is turned off
Selectable Illumination [KEY ILLUMI]
Selecting the button illumination color as green or red. Touch [7GREEN] [7RED] Setting The illumination color is green. The illumination color is red.
On Screen Display [AUTO ON SCREEN]
Touch [7AUTO] Setting When a button on the main unit or remote control unit is pressed, or the disc track is changed, the audio source control information is temporarily superimposed on the picture. When the lower canter of the screen is touched while a TV/video picture is displayed, the audio source control information is temporarily superimposed on the picture.
Key Indicator Color [KEY INDICATOR]
Selecting the OPEN and SRC button indicator color. Touch the [2] or [3] button. Display Setting "SOURCE" The color changes according to the selected source. "MARS" Red "LIME" Green "SUNSET Red Green "SKY" Blue "VIOLET" Violet "AQUA" Blue Green "MOON" White
[7MANU]
Disabled System Indicator [DSI]
A red indicator (Reset button) will blink on the unit after the ignition Key switch is off , warning potential thieves. Touch [7ON] [7OFF] Setting LED flashes. LED OFF.
Navigation Announcement [NAV INTERRUPTION]
The navigation voice is output from the front speaker at navigation voice guide announcement time. Touch [7ON] [7OFF] Setting Announcement function is on Announcement function is off
Switching the Setup Screen -1 and 2
Touch the [ 2 ] or [ 3 ] button.
This function available when the KENWOOD navigation unit is connected to the I/F terminal.
Sound Attenuate [NAV GUIDE]
The rear speaker sound is attenuate during the navigation voice output time. Touch [7ATT] [7SOUND] Setting Rear speaker attenuate function is on Rear speaker attenuate function is off
This function available when the KENWOOD navigation unit is connected to the I/F terminal.
12
Exit the System Setup Screen
Touch the [RTN] button. Return to the setup menu screen.
13
Tuner Setting Function
Tuner Setting Menu Screen
ME NU SOUND R D S SETUP TV 1 2:0 0 TUNER A F O AREA R E G O D A B A U T O O SOURC E RDS N T P N OF F S E E K OF F RTN N OF F N EWS 1 0M I N
RDS Setting Screen
SETUP
Selecting the RDS Setting Screen
Touch the [RDS] button. ( Page 14)
News Bulletin with Timeout Setting [NEWS]
It switches automatically when a news bulletin starts even if the radio isn't being listened to. Also, the time interval when interrupt is prohibited can be set. Touch the [ 2 ] or [ 3 ] button. Display and Setting "NEWS OFF" "NEWS 00MIN" "NEWS 90MIN" When "NEWS 00MIN" -- "NEWS 90MIN" is set, the News Bulletin Interrupt function is ON. When it's ON, the "NEWS " indicator is ON in the source control screen. When the news bulletin starts, "NEWS " is displayed in the source control screen, and it switches to the news bulletin.
· If you choose the "20MIN" setting, further news bulletins will not be received for 20 minutes once the first news bulletin is received. · The news bulletin volume is the same level that was set for traffic information (page 23). · This function is only available if the desired station sends PTY-code for news bulletin or belongs to -Network sending PTY-code for news bulletin. · When the News Bulletin Interrupt function is ON, it switches to an FM station.
Selecting the TV Area Setting Screen
Touch the [TV AREA] button. ( Page 15) (During the KTC-V500E is connected)
Selecting the DAB Tuner Setting Screen
Touch the [DAB] button. ( Page 31) (During the KTC-9090DAB is connected)
Alternative Frequency Function [AF]
When poor reception is experienced, automatically switch to another frequency broadcasting the same program in the same RDS network with better reception. Touch [7ON] [7OFF] Setting AF function is turned on AF function is turned off
When the AF function is ON, the "RDS" indicator is ON in the source control screen.
When no other stations with stronger reception are available for the same program in the RDS network, you may hear the incoming broadcast in bits and snatches. Turn OFF the AF function in such a case.
14
...
TV Area Setting Screen
T 1 V 1 2 T 3 V 2 4 5 6
· F r a n c e
TV
AREA
SET
RTN
Region Restrict Function [REG]
You can choose whether or not to restrict the RDS channels, received with the AF function for a particular network, to a specific region. Touch [7ON] [7OFF] Setting Region restrict function is turned on Region restrict function is turned off
Setting the TV Area
Select the area for TV broadcast viewing. Selecting the Preset Bands: Touch the [TV 1] or [TV 2] button. Selecting the Reception Area: Touch the [71] - [76 ] button. Select the channel setting for your country as follows. [71] Germany Spain Portugal Netherlands Belgium Switzerland Austria Sweden Norway Denmark Finland Yugoslavia Iceland Italy Albania United Kingdom Ireland France Russia Poland Hungary Czech Slovakia Bulgaria Romania Greece PAL-I SECAM-L SECAM-D/K PAL-B/G
Sometimes stations in the same network broadcast different programs or use different program service names.
Auto TP Seek Function [ATPS]
When the TI function is ON and poor reception conditions are experienced when listening to a traffic information station, another traffic information station with better reception will be searched for automatically. Touch [7ON] [7OFF] Setting Auto TP seek function is turned on Auto TP seek function is turned off
[72] [73] [74] [75]
Exit the RDS Setting Screen
Touch the [RTN] button. Return to the tuner setting menu screen.
[76]
SECAM-B/G
The reception area can be set for two separate preset bands TV1 and TV2.
Exit the TV Area Setting Screen
Touch the [RTN] button. Return to the tuner setting menu screen.
15
Sound Control Function
Sound Control Menu Screen
ME NU SOUND SETUP 1 2:0 0 TUNER E s AMP L SP SE L T ON E R SOURC E AUD I O R FREQ NM L BA L / FAD F
Audio Setting Screen-1
L OUD O N AMP O F F
BASS F L T
AUD I O
SYS
V . OF FSET OF F RTN
Selecting the Audio Setting Screen
Touch the [AUDIO] button.( Page 16)
You cannot operate when the standby mode is selected.
Balance and Fader [BAL/FAD]
Touch [2]L [3]R [5]F []R Setting The sound in the left channel is emphasized. The sound in the right channel is emphasized. The sound in the front channel emphasized. The sound in the rear channel emphasized.
Selecting the System Es Setting Screen
Touch the [SYS Es] button.( Page 19)
You cannot operate when the standby mode is selected.
Selecting the Speaker Select Screen
Touch the [SP SEL] button.( Page 18)
You can operate when the standby mode is selected.
Loudness [LOUD]
Compensating for low and high tones during low volume. Touch [7ON] [7OFF] Setting Loudness function is turned on Loudness function is turned off
Selecting the Tone Control Screen
Touch the [TONE] button.( Page 18)
You cannot operate when the standby mode is selected.
When the Loudness function is ON, the "LOUD" indicator is ON in the source control screen.
B.M.S. (Bass Management System) [AMP BASS]
Adjust the bass boost level of the external amplifier using the main unit. Touch the [ 2 ] or [ 3 ] button. Display Setting "FLT" Bass boost level is flat. "+6dB" Bass boost level is low (+6dB). "+12dB" Bass boost level is mid (+12dB). "+18dB" Bass boost level is high (+18dB).
· Refer to the catalog or instruction manual for power amplifiers that can be controlled from this unit. · For amplifiers there are the model that can be set from Flat to +18 dB, and the model that can be set from Flat to +12 dB. When an amplifier is connected that can only be set to +12dB, even if "+18dB" is selected it won't operate correctly.
B.M.S. Frequency Offset [AMP FREQ]
Setting the central frequency boosted by B.M.S. Touch the [ 2 ] or [ 3 ] button. Display Setting "NML" Boost with the normal central frequency. "LOW" Drop the normal central frequency 20%.
Refer to the catalog or instruction manual for power amplifiers that can be controlled from this unit.
16
Audio Setting Screen-2
S Y S T EM Q TOP 4 0 S Y S T EM O N 2 Z ON E O N QE x O F F O F F
AUD I O
RTN
Volume Offset [V OFFSET]
Each source's volume can be set as a difference from the basic volume. Touch [3] [2] Setting The level is increased. The level is decreased.
Dual Zone System [2 ZONE]
The following operation allows separate sound sources to control the output of the front and rear speakers. Touch [7ON] [7OFF] Setting The dual zone system function is on. AV-OUT sound send to the rear speaker. The dual zone system function is off.
Switching the Audio Setting Screen -1 and 2
Touch the [2] or [3] button.
System Q [SYSTEM Q]
You can recall the best sound setting preset for different types of the music. Touch the [2] or [3] button. Display Setting "FLAT" Flat. "ROCK" Rock "TOP 40" Top 40 "POPS" Pops "JAZZ" Jazz "EASY" Easy "USER" User memory
· User memory: The values set on the (page 18). · Each setting value is changed on the (page 18). First, select the Speaker and Woofer type with the .
· When the Dual Zone System is ON, there is no rear channel audio control or other effect. · When you set the Dual zone system to ON while the nonfading preout is switched ON, the sound of the non-fading preout isn't output.
Exit the Audio Setting Screen
Touch the [RTN] button. Return to the sound control menu screen.
System Q Ex [SYSTEM QEx]
Setting display/don't display for the System Q factors (Bass center frequency, Bass Q factor, Bass extend, Middle center frequency, Middle Q factor, and Treble center frequency) in Tone control screen. Touch [7ON] [7OFF] Setting The System Q factors are displayed. The System Q factors aren't displayed.
17
Sound Control Function
Speaker Select Screen
SPEAKER 6 * 9 / 6 i n c h WO O F E R 1 2 i n
Tone Control Screen (Ex:OFF)
BASS L EVE L 0 L EVE L 2 L EVE L 1 RTN
M I D
t y p eA
TRE
SP
SE L
RTN
T ON E
Speaker & Woofer Setting
Fine-tuning so that the System Q value is optimal when setting the speaker and woofer type. Touch the [2] or [3] button. In Speaker setting mode [SPEAKER] Display Speaker type "OFF" Off "6*9/6inch" For 6 & 6x9 inch speaker "5/4inch" For 5 & 4 inch speaker "OEM" For the OEM speaker In Woofer setting mode [WOOFER] Display Woofer type "OFF" Off "12in typeA" 12 inch A type "10in typeA" 10 inch A type "12in typeB" 12 inch B type "10in typeB" 10 inch B type "12in typeC" 12 inch C type "10in typeC" 10 inch C type "8inch" 8 inch type "12in typeD" 12 inch D type "10in TypeD 10 inch D type
Tone Control (System QEx set to OFF)
Touch the [2] or [3] button. Display Adjustment Item "BASS LEVEL" Bass level "MID LEVEL" Middle level "TRE LEVEL" Treble level
Range 8 -- +8 8 -- +8 8 -- +8
Exit the Tone Control Screen
Touch the [RTN] button. Return to the sound control menu screen.
Exit the Speaker Select Screen
Touch the [RTN] button. Return to the sound control menu screen.
18
Tone Control Screen -1 (Ex:ON)
BASS f 1 5 0 BASS BASS EXT O N O F F
System Es Setting Screen
HPF F 1 2 0 R 1 2 0 L PF N - F 8 0 L EVE L 0 0
L EVE L 1
HPF
N - F
BASS Q 2 . 0 0 T ON E RTN
N - F PHASE NORMA L S Y S T EM E s
REVERSE RTN
Tone Control Screen -2 (Ex:ON)
System Es
M I D f 1 2 0 M I D L EVE L 1 TRE f 1 7 . 5 TRE L EVE L 1
M I D Q 2 . 0 0 T ON E RTN
Range Through/40/60/ 80/100/120/150/ 180/220 (Hz) "HPF R" Rear High Pass Filter Through/40/60/ 80/100/120/150/ 180/220 (Hz) "LPF N-F" Non-Fading Low Pass 50/80/120/ Filter Through (Hz) "N-F LEVEL" Non-Fading level 15 -- +15 "N-F PHASE" Non-Fading Phase 7NORMAL (0°)/ 7REVERSE(180°)
Touch the [2] or [3] button. Display Adjustment Item "HPF F" Front High Pass Filter
Tone Control (System QEx set to ON)
Touch the [2] or [3] button. Display Adjustment Item Range "BASS f" Bass Center Frequency 60/70/80/100 or 150 Hz "BASS LEVEL"Bass level 8 -- +8 "BASS Q" Bass Q Factor 1.00/ 1.25/ 1.50/ 2.00 "BASS EXT" Bass Extend 7ON(On) 7OFF(Off) "MID f" Middle Center 0.5/1.0/1.5/ Frequency 2.0kHz "MID LEVEL" Middle level 8 -- +8 "MID Q" Middle Q Factor 1.00/2.00 "TRE f" Treble Center 10.0/12.5/15.0/ Frequency 17.5 kHz "TRE LEVEL" Treble level 8 -- +8
· According to the Bass Q Factor setting value, the frequencies that can be set in Bass Center Frequency change as shown below. Bass Q Factor Bass Center Frequency 1.00/1.25/1.50 60/70/80/100 Hz 2.00 60/70/80/150 Hz · When the Bass Extend is set to ON, low frequency response is extended by 20%.
Exit the System Es Screen
Touch the [RTN] button. Return to the sound control menu screen.
Switching the Tone Control Screen -1 and 2
Touch the [ 2 ] or [ 3 ] button.
Exit the Tone Control Screen
Touch the [RTN] button. Return to the sound control menu screen.
19
Source Control Function (Common operation)
On Screen Control
T I
Source Control Screen
ME NU TUNER FM3 P 1 FM - I NFO ATT LOUD LIST FM PTY P 1 P 2 P 3 P 4 P 5 P 6 9 2 . 5 M Hz 1 2:0 0
SRC
AM FM3 P 1 1 0 8 . 5 FM - I NFO P 1 P 2 P 3 P 4 P 5
FM M Hz P 6
AM INFO
Attenuator
Turning the volume down quickly. Press the [ATT] button. Each time the button is pressed the Attenuator turns ON or OFF. When it's ON, the "ATT" indicator is ON.
FNC
SRC MODE
AM
ATT
4 ¢
FM
Displaying the On Screen Control
Selecting the On Screen Control Press the [FNC] button to switch the on screen control display.
If you make no button operation for 10 seconds, the on screen control is automatically cancelled.
Loudness
Compensating for low and high tones during low volume. Press the [ATT] button for at least 1 second. Each time the button is pressed for at least 1 second the Loudness turns ON or OFF. When it's ON, "LOUD" indicator is ON.
Selecting the Control Screen When the [FNC] button is pressed during on screen control display, it switches to control screen.
Non-fading Output
Turning the Non-fading output ON or OFF. Press the [AM] button for at least 1 second. Each time the button is pressed for at least 1 second the Non-fading output switches ON or OFF.
Changing the Audio Source Mode
Press/ Touch the [SRC] button.
Touch the [2] or [3] button. Source required FM/AM Tuner External CD player External disc changer Video & External TV Tuner Auxiliary input External DAB Tuner Standby (Illumination only mode)
Switching to the Menu Screen
Display "TUNER" "CD" "DISC-CH" "MD-CH" "AV" "AUX" "DAB" "ALL OFF" Touch the [MENU] button.( Page 8)
Changing the Function Buttons
Touch the [ ] button. Each time the button is touched the under function buttons change.
For Auxiliary input one of the below optional accessories is necessary. - KCA-S210A - CA-C1AX - CD changer with an Auxiliary input function installed.
Changing the Background Mode for the Control Screen
You can select the background between 11 different patterns for the source control screen and menu screen. Press the [MODE] button. Each time the button to change the background mode.
Volume
Increasing Volume: Press the [u] button. Decreasing Volume: Press the [d] button.
20
TEL Mute
The audio system automatically mutes when a call comes in. When a call comes in "CALL" is displayed. The audio system pauses. Listening to the audio during a call Press the [SRC] button. The "CALL" display disappears and the audio system comes back ON. When the call ends Hang up the phone. The "CALL" display disappears and the audio system comes back ON.
21
FM/AM Tuner Control Function
On Screen Control
T I
Control Screen -1
ME NU TUNER FM3 P 1 FM - I NFO MANU AM INFO P 1 P 2 P 3 P 4 P 5 9 2 . 5 LO.S FM PTY P 6 M Hz TI ST 1 2:0 0
NEWS MONO RDS LIST
SRC
AM FM3 P 1 1 0 8 . 5 FM - I NFO P 1 P 2 P 3 P 4 P 5
FM M Hz P 6
Auto Memory Entry
AM 4 ¢ FM
Putting stations with good reception in the memory automatically. 1 Select the band for Auto Memory Entry Touch the [FM] or [AM] button.
Selecting the FM Band
Press/ touch the [FM] button. Each time the button is pressed/ touched it switches between the FM1, FM2, and FM3 bands.
2 Open Auto Memory Entry Touch the [AME] button for at least 2 seconds. When 6 stations that can be received are put in the memory Auto Memory Entry closes.
· When the (page 14) is ON, only RDS stations are put in the memory. · When Auto Memory Entry is done in the FM2 band, the RDS stations preset in the FM1 band aren't put in the memory. Likewise, when it is done in the FM3 band, RDS stations preset in FM1 or FM2 aren't put in the memory.
Selecting the AM Band
Press/ touch the [AM] button.
Tuning
Press/ touch the [4] or [¢] button. During reception of stereo stations the "ST" indicator is ON
Seek Mode
Sets the seeking mode. Touch the [SEEK] button. Each time the button is touched the seeking mode switches as shown below. Seek mode(display) Operation Auto seek ("AUTO1") Automatic search for a station. Preset station seek ("AUTO2") Search in order of the stations in the Preset memory. Manual ("MANU") Normal manual tuning control.
Station Preset Memory
Putting the station in the memory. 1 Select the band Press/ touch the [FM] or [AM] button. 2 Select the frequency to put in the memory Press/ touch the [4] or [¢] button. 3 Put the frequency in the memory Touch the [P1] -- [P6] button for at least 2 seconds. On each band, 1 station can be put in the memory on each [P1] -- [P6] button.
Monaural Reception
Noise can be reduced when stereo broadcasts are received as monaural. Touch the [MONO] button. Each time the button is touched the Monaural Reception turns on or off. When it's on, the "MONO" indicator is On
Preset Tuning
Calling up the stations in the memory. 1 Select the band Press/ touch [FM] or [AM] button. 2 Call up the station Touch the [P1] -- [P6] button.Auto Memory
Local Seek
Only stations whose reception is good are searched for in auto seek tuning. Touch the [LO.S] button. Each time the button is touched the local seek function on and off. When it's on, the LO.S indicator is on.
22
Control Screen -2
T I ME NU TUNER FM3 P 1 FM - I NFO 9 2 . 5 LO.S FM PTY AME TI VOL SEEK MONO LO.S DISP M Hz TI ST 1 2:0 0
MANU
NEWS MONO RDS LIST
AM INFO
Traffic Information
Switching to traffic information automatically when a traffic bulletin starts even when you aren't listening to the radio. Touch the [TI] button. Each time the button is touched the Traffic Information function turns ON or OFF. When it's ON, "TI" indicator is ON. When a traffic bulletin starts, "TRAFFIC INFO" is displayed it and it switches to traffic information.
During reception of a AM station when the Traffic Information function is turned ON, it switches to a FM station.
Switching Display
Switching the information displayed. Touch the [DISP] button. Each time the button is touched the display switches as shown below. Information Display Program Service name "STATION NAME" Radio text "RADIO-TEXT" Switching to the Radio Text Information Screen The whole sentence of radio text is displayed. Touch the [INFO] button.
R # # # # # # # # # # # A # # # # # # # # # # # D # # # # # # # # # # # I # # # # # # # # # # # O # # # # # # # # # # # # # # # # # # # # # # T # # # # # # # # # # # E # # # # # # # # # # # X # # # # # # # # # # # T # # # # # # # # # # # # # # # # # # # # # # # # # # # # # # # # # # # # # # # # # # # # # # # # # # # # # # # # # # # # # # # # # # # # # # # # # # # # # # # # # # # # # # # # # # # # # # # # # # # # # # # # # # # # # #
Presetting Volume for Traffic Information
Setting the volume during Traffic Information. 1 Receive the station 2 Set the volume you want 3 Preset the volume Touch the [TIVOL] button for at least 2 seconds.
I NFO
RTN
Page Up/Down for the Radio text Touch the [5] or [] button.
When all text are displayed on the information screen, [] and [5] do not appear.
Exit the Information Screen Touch the [RTN] button. Return to the source control screen.
Switching to the FM/AM List Screen
Touch the [LIST] button. ( page 24)
Switching to the PTY Search Screen
Touch the [PTY] button. ( page 24)
This function can't be used during a traffic bulletin or AM reception.
23
FM/AM Tuner Control Function
FM/AM List Screen
FM1 1 PS 2 PS P 1 9 2 . 5 M Hz
PTY Search Screen
FM - I NFO L e i s u r e P T Y S o c i a l L A N G E n g l i s h & Ho b b y
N AME # # # # # N AME # # # # # FM AM
A f f a i r s
3 1 7 5 . 5 MH z # # # # 4 PS 5 PS 6 PS N AME # # # # # N AME # # # # # N AME # # # # #
RTN
SEARCH
RTN
FM/AM List Screen
Selecting the FM band Touch the [FM] button. Each time the button is touched it switches between the FM1, FM2, and FM3 bands. Selecting the AM band Touch the [AM] button. Call up the station Touch the list. Exit the FM/AM List Screen Touch the [RTN] button. Return to the source control screen.
23. 24. 25. 26. 27. 28. 29. 30. 31.
Phone In Travel Leisure Jazz Music Country Music National Music Oldies Music Folk Music Documentary
"Phone In" "Travel & Touring" "Leisure & Hobby" "Jazz Music" "Country Music" "National Music" "Oldies Music" "Folk Music" "Documentary"
Speech and Music include the Program types shown below. Music: No.12 -- 17, 26 -- 30 Speech: No.3 -- 11, 18 -- 25, 31
PTY Search Screen
Selecting the Program Type and searching for a station. Select the Program Type [PTY] Touch the [2] or [3] button. Each time the button is touched the Program Type switches as shown below. No. Program Type 1. Speech 2. Music 3. News 4. Current Affairs 5. Information 6. Sport 7. Education 8. Drama 9. Culture 10. Science 11. Varied 12. Pop Music 13. Rock Music 14. Easy Listening Music 15. Light Classical 16. Serious Classical 17. Other Music 18. Weather 19. Finance 20. Children's programs 21. Social Affairs 22. Religion Display "All Speech" "All Music" "News" "Current Affairs" "Information" "Sport" "Education" "Drama" "Cultures" "Science" "Varied Speech" "Pop Music" "Rock Music" "Easy Listening M" "Light Classic M" "Serious Classics" "Other Music" "Weather & Metr" "Finance" "Children's Prog" "Social Affairs" "Religion"
Select the language [LANG] Touch the [2] or [3] button. Language Display English "ENGLISH" French "FRENCH" German "GERMAN" Search for the selected Program Type station Touch the [SEARCH] button. When you want to search for other stations touch the [SEARCH] button again.
When the selected Program Type isn't found, "NO PTY" is displayed. Select another Program Type.
Exit the PTY Search Screen Touch the [RTN] button. Return to the source control screen.
24
AV Control Function (TV Control: During the KTC-V500E is connected)
On Screen Control
AU T O 2 TV1 1 0 c h
Control Screen-1
T I ME NU A V 1 2 c h 1 2:0 0
W I DE C I N E MA SRC TV 1 A 1 P 1 NO N AME P 1 P 2 P 3 P 4
AV OU T V I DE O1 TV 1 2 c h P 5 P 6
TV 1 A 1 P 1 NO N AME MANU AV
TV
P 1
P 2
P 3
P 4
P 5
P 6
Control Screen-2
T I ME NU A V 1 2 c h 1 2:0 0
AM
4 ¢ FM
MANU
TV 1 A 1 P 1 NO N AME
Selecting the On Screen Control
Touch the centre part.
If you make no button operation for 10 seconds, the on screen control is automatically cancelled.
AV
TV
AME
LIST
SEEK
NAME
P 7
P 8
Selecting the Preset Band
Press the [FM] button. Each time the button is pressed the preset band switches between the TV1 and TV2.
Selecting the Channel
Press the [4] or [¢] button.
Touch the [4] or [¢] button.
Touch the [TV] button. Each time the button is touched the preset band switches between the TV1 and TV2.
Touch the left or right side part.Preset
Station Preset Memory Selecting the Video Input
Press the [AM] button. Each time the button is pressed the video input switches between the AV IN 1, AV IN2 and RGB. Putting the station in the memory. 1 Select the band Press/ touch the [FM] button. 2 Select the channel to put in the memory Press/ touch the [4] or [¢] button. 3 Put the channel in the memory Touch the [P1] -- [P8] button for at least 2 seconds. On each band, 1 station can be put in the memory on each [P1] -- [P8] button.
Touch the [AV] button. Each time the button is touched the video input switches between the AV IN 1, AV IN2 and RGB.
Video1 and 2: During "AV IN1" and "AV IN2" set to "VD",
Seek Mode
Sets the seeking mode. Touch the [SEEK] button. Each time the button is touched the seeking mode switches as shown below. Seeking mode(display) Operation Auto seek ("AUTO1") Automatic search for a station. Preset station seek ("AUTO2") Search in order of the stations in the Preset memory. Manual ("MANU") Normal manual seeking control.
25
AV Control Function
Control Screen-1
T I ME NU A V 1 2 c h 1 2:0 0 TV 1
TV List Screen
P 1 1 2 c h
1 I NFO - TV 2 TV - J APAN 3 TV 3 c h TV
TV 1 A 1 P 1 NO N AME MANU AV
4 1 0 c h 5 1 1 c h
P 1
P 2
P 3
P 4
P 5
P 6
6 1 2 c h
RTN
Control Screen-2
T I ME NU A V 1 2 c h 1 2:0 0
TV List Screen
Selecting the TV preset band Touch the [TV] button. Each time the button is touched it switches between the TV1, and TV2 bands. Switching the List Touch the [ ] button. Each time the button is touched the list switches between the [P1] -- [P6] and [P7] -- [P8]. Call up the channel Touch the list. Exit the TV List Screen Touch the [RTN] button. Return to the source control screen.
TV 1 A 1 P 1 NO N AME MANU AV
TV
AME
LIST
SEEK
NAME
P 7
P 8
Auto Memory Entry
Putting stations with good reception in the memory automatically. 1 Select the band for Auto Memory Entry Touch the [TV] button. 2 Open Auto Memory Entry Touch the [AME] button for at least 2 seconds. When 8 stations that can be received are put in the memory Auto Memory Entry closes.
Recalling a Preset Station
1 Select the band 2 Call up the station Touch the [P1] -- [P8] button.
Switching to the TV List Screen
Touch the [LIST] button.
Switching to the Name Set Screen
Touch the [NAME] button. For the setting method refer to the name set screen ( page 30).
You cannot operate unless the parking brake is set.
26
CD Player Control Function
On Screen Control
T I
Control Screen-1
ME NU C D 1 2:0 0
Track 1 2 1 2 : 3 4 DNPS # # # # # # # # # # # # REP
SRC Track 1 2 1 2 : 3 4 DNPS # # # # # # # # # # # # SCN REP RDM
SCN
REP
RDM
Control Screen-2
T I ME NU C D 1 2:0 0
4 ¢
Track 1 2 1 2 : 3 4 DNPS # # # # # # # # # # # # REP
Pause and play
Touch the [38] button. Each time the button is touched it pauses and plays.
Fast Forwarding and Reversing
Fast Forwarding Hold down on the [¢] button. Release your finger to play the disc at that point. Reversing Hold down on the [4] button. Release your finger to play the disc at that point.
NAME
Random Play
Playing all the songs on the disc in random order. Touch the [RDM] button. Each time the button is touched Random Play turns ON or OFF. When it's ON, the "RDM" indicator is ON.
When the [¢] button is touched, the next song select starts.
Track Search
Selecting the song you want to hear. Press/ touch the [4] or [¢] button.
Track Repeat
Replaying the song you're listening to. Touch the [REP] button. Each time the button is touched the Track Repeat turns ON or OFF. When it's ON, "REP" indicator is ON.
Switching to the Name Set Screen
Touch the [NAME] button. For the setting method refer to the name set screen ( page 30).
You cannot operate unless the parking brake is set.
Track Scan
Playing the first part of each song on the disc you are listening to and searching for the song you want to listen to. 1 Start Track Scan Touch the [SCN] button. "SCN" indicator is ON.
2
Release it when the song you want to listen to is played Touch the [SCN] or [38] button.
27
Disc Changer Control Function
On Screen Control
T I
Control Screen-1
ME NU D I SC - CH Disc 5 - Track 1 2 2 : 3 4 D I SCTEXT # # # # REP 1 2:0 0
SRC
D D+ 1 2 2 : 3 4 Disc 5 - Track D I SCTEXT # # # # SCN DREP REP MRDM RDM
D -
D+
SCN
DREP
REP
MRDM
RDM
Album Repeat
4 ¢ FM
Replaying the disc in the Disc changer you're listening to. Touch the [DREP] button. Each time the button is touched Album Repeat turns ON or OFF. When it's ON, the "DREP" indicator is ON.
The 3+1MD changer cannot be operated when 4 discs are inserted.
AM
Pause and play
Touch the [38] button. Each time the button is touched it pauses and plays.
Track Scan Fast Forwarding and Reversing
Fast Forwarding: Hold down on the [¢] button. Release your finger to play the disc at that point. Reversing: Hold down on the [4] button. Release your finger to play the disc at that point. Playing the first part of each song on the disc you are listening to and searching for the song you want to listen to.
1 2
Start Track Scan Touch the [SCN] button. "SCN" indicator is ON. Release it when the song you want to listen to is played Touch the [SCN] or [38] button.
Track Search
Selecting the song you want to hear. Press/ touch the [4] or [¢] button.
Random Play
Playing all the songs on the disc in random order. Touch the [RDM] button. Each time the button is touched Random Play turns ON or OFF. When it's ON, the "RDM" indicator is ON.
When the [¢] button is touched, the next song select starts.
Album Search
Selecting the disc you want to hear. Touch the [D+] or [D] button. Press the [FM] or [AM] button.
The 3+1MD changer cannot be operated when 4 discs are inserted.
Track Repeat
Replaying the song you're listening to. Touch the [REP] button. Each time the button is touched the Track Repeat turns ON or OFF. When it's ON, "REP" indicator is ON.m Repeat
Magazine Random Play
Play the songs on all the discs in the disc changer in random order. Touch the [MRDM] button. Each time the button is touched Magazine Random Play turns ON or OFF. When it's ON, the "MRDM" indicator is ON.
· When the [¢] button is touched, the next song select starts. · The 3+1MD changer cannot be operated when 4 discs are inserted.
28
Control Screen-2
T I ME NU D I SC - CH 1 Disc 5 - Track 1 2 2 : 3 4 D I SCTEXT # # # # REP D D+ 1 2:0 0
Disc List Screen
D - TEXT L I ST Disc 5 - Track 1 2 1 2 : 3 4 1 B e s t 2 B e s t 3 NO 4 NO 5 NO H i t - V 1 H i t - V 2 DISP
TEXT TEXT TEXT TEXT RTN
LIST
INFO
NAME
DISP
6 NO
Disc List Screen
Switching Display
Touch the [DISP] button. Each time the button is touched the display switches as shown below. Display Information "DNPS" Disc name (CD only) "D-TEXT"/"D-TITLE" Disc text/ Disc title "T-TEXT"/"T-TITLE" Track text/ Track title Switching to the Text/Title Information Screen The whole sentence of CD text or MD title is displayed. Touch the [INFO] button.
D # # # # # # # # # # # # # # # # # # # # # # T # # # # # # # # # # # E # # # # # # # # # # # X # # # # # # # # # # # T # # # # # # # # # # # # # # # # # # # # # # # # # # # # # # # # # # # # # # # # # # # # # # # # # # # # # # # # # # # # # # # # # # # # # # # # # # # # # # # # # # # # # # # # # # # # # # # # # # # # # # # # # # # # # # # # # # # # # # # # # # # # # # # # # # # # # # # # # # # # # # # # # # # # # # # # # # Disc 3 - Track 1 B e s t 2 B e s t 3 NO 4 1 2 1 2 : 3 4
H i t - V 1 H i t - V 2
T I T L E
RTN
Disc List Screen
Changing the Disc List (10 disc changer only) Touch the [ ] button. Each time the button is touched he disc list switches between the disc1-6 and disc 7-10. Switching the Display for Discs (CD only) Touch the [DISP] button. Each time the button is touched the list switches between the DNPS and CD text. Selecting the Disc Touch the list.
The 3+1MD changer cannot be operated when 4 disks are inserted.
I NFO
RTN
Page Up/Down for the CD text or MD title Touch the [5] or [] button.
When all text are displayed on the information screen, [] and [5] do not appear.
Exit the Information Screen Touch the [RTN] button. Return to the source control screen.
Exit the Disc List Screen Touch [RTN] button. Return to the source control screen.
Switching to the Disc List Screen
Touch the [LIST] button.
Switching to the Name Set Screen
Touch the [NAME] button. For the setting method refer to the name set screen ( page 30).
You cannot operate unless the parking brake is set.
29
Name Set Function
Name Set Screen
N AME # P R E S E T # A A B G a b M 1 2 S Ä ä Y N AME Z SET , . · O K T U V W X N O P Q R S P C H I J K L B C D E F
Station Name Preset (SNPS)/ Disc Name Preset (DNPS)
1 Move the cursor to the enter character position Touch the [<] or [>] button. 2 Select the character type Touch the [AB], [ab], [12] or [Ää] button. 3 Select the character list Touch the [] or [5] button.
When all characters are displayed on the character list, [] and [5] do not appear.
4 Touch a character. 5 Repeat steps 1 through 4 and enter the name.
· You can enter up to 12 characters for each name. · To enter a space, touch the [SPC] button.
6 Exit name set screen Touch the [OK] button.
· Media that you can attach names to TV tuner: 100 stations. External CD changer/ player: Varies according to the CD changer/player. Refer to the CD changer/ player manual. · The name of a CD can be changed by the same operation you used to name it.
30
Other Option Control Function
7 DAB Tuner Control
DAB Tuner Setting Screen-1
D A B O D R C ON P R I O R I T Y N OF F OF F R E G I N T ON OF F T R A V E L ON OF F N EWS ON OF F RTN DAB SET RTN
DAB Tuner Setting Screen-2
WE A T H E R ON OF F S P E C I A L ON OF F S P O R T S ON OF F E V E N T ON
OF F
R A D I N F O ON OF F F I N A N C E ON OF F
T R A F F I C ON OF F WA R N I N G ON OF F DAB SET
Refer to the KTC-9090DAB's instruction manual for DAB tuner features. Automatic Switching DAB priority [DAB PRIORITY]
Touch Setting [7ON] DAB priority function is turned on [7OFF] DAB priority function is turned off When it's ON, the "PR" indicator is displayed in the source control screen.
Announcement select mode
Touch [7ON] [7OFF] Display "TRAFFIC" "TRAVEL" "WARNING" Setting On Off Contents Traffic information Time table information of public transportation services Lower priority items than Alarm (power failure, cut-off of the water supply, etc.) News flash Weather forecasting Event information Undetermined event information Programme information, advance notice Sports news Financial news
Dynamic Range Control [DRC]
Touch Setting [7ON] DRC function is turned on [7OFF] DRC function is turned off When it's ON, the "DRC" indicator is displayed in the source control screen.
"NEWS" "WEATHER" "EVENT" "SPECIAL" "RAD INFO" "SPORTS" "FINANCE"
Regional Announcement Function [REG INTRUPT]
Touch [7ON] [7OFF] Setting Regional announcement function is turned on Regional announcement function is turned off
Exit the DAB Tuner Setting Screen
Touch the [RTN] button. Return to the tuner setting menu screen.
Switching the DAB Tuner Setup Screen -1 and 2
Touch the [ 2 ] or [ 3 ] button.
31
Other Option Control Function 7 DAB Tuner Control
On Screen Control
T I
Control Screen-1
ME NU D A B DAB 1 P 1 1 4 5 1 . 0 7 E N S EMB L E L A B E L # # AUTO1 NEWS RDS DRC 2 # TI PR 1 2:0 0
SRC
S DAB ENS P 1 P
BAND S + 1 P 1 1 4 5 1 . 0 2 EMB L E L A B E L # # # 2 P 3 P 4 P 5 P 6
S INFO P 1 P 2
BAND
S + PTY
P 3
P 4
P 5
P 6
Switching the Service Component
Touch the [P/S] button. Each time the button is touched it switches between the Primary and Secondary. When the Primary is selected, the "PR" indicator is ON. When the Secondary is selected, the "SC" indicator is ON.
AM
4 ¢ FM
Refer to the KTC-9090DAB's instruction manual for DAB tuner features. Switching the Pre-set band
Touch the [BAND] button. Each time the button is touched the preset band switches between the DAB1, DAB2, and DAB3 bands.
Seek Mode
Touch the [SEEK] button. Each time the button is touched the Seek mode switches as shown below. Display Setting "AUTO1" Auto Ensemble Seek AUTO2" Pre-set Service Call "MANU" Manual Seek
DAB Reception
Switching the Ensemble Press/ touch the [4] or [¢] button. Switching the service
Presetting Volume for Announcement
1 Set the volume you want 2 Preset the volume Touch the [TIVOL] button for at least 2 seconds.
Press the [FM] or [AM] button.
Touch the [S+] or [S-] button.
Service Preset Memory
Touch the [P1] -- [P6] button for at least 2 seconds. Recalling a Preset Service Touch the [P1] -- [P6] button.
Traffic Announcement Function
Touch the [TI] button. Each time the button is touched the interrupting function of the Traffic Announcement on/off.
Auto Ensemble Memory Entry
1 Select the band Touch the [BAND] button. 2 Open Auto Memory Entry Touch the [AME] button for at least 2 seconds.
32
Control Screen-2
T I ME NU D A B DAB 1 P 1 1 4 5 1 . 0 7 E N S EMB L E L A B E L # # AUTO1 NEWS RDS DRC S INFO AME TI VOL SEEK LANG P/S BAND S + PTY DISP 2 # TI PR 1 2:0 0
DAB PTY Search Screen
P S # N AME # # # # # # # # # P T Y #GENRE # # # # # # # P T Y New s L A N G E n g l i s h O WA T C H P o p s SEARCH Mu s i c RTN N OF F
Switching Display
Touch the [DISP] button. Each time the button is touched the display switches as shown below. Display Item "SERVICE LABEL" Service Label "ENSEMBLE LABEL" Ensemble Label "PTY LABEL" PTY label "COMPO LABEL" Component label "REGION LABEL" Region label "AUDIO QUALITY" Audio quality "DYNAMIC LABEL" Dynamic label Switching to the Dynamic Label Information Screen The whole sentence of Dynamic label information is displayed. Touch the [INFO] button.
D S # # # # # # # # # # Y E # # # # # # # # # # N R # # # # # # # # # # AM I C V I CE # # # # # # # # # # # # # # # # # # # # # # # # # # # # # # # # # # # # # # # # L N # # # # # # # # # # ABE AME # # # # # # # # # # # # # # # # # # # # # # # # # # # # # # L # # # # # # # # # # # # # # # # # # # # # # # # # # # # # # # # # # # # # # # # # # # # # # # # # # # # # # # # # # # # # # # # # # # # # # # # # # # # #
DAB PTY Search Screen
Selecting the Programme Type for Search [PTY] Touch the [2] or [3] button. Searching by programme type and language [LANG] Touch Setting [7ON] Search function is on [7OFF] Search function is off Selecting the Programme Type for Watch [WATCH] Touch the [2] or [3] button. Searching the Programme Type Touch the [SEARCH] button. Exit the PTY Search Screen Touch the [RTN] button. Return to the source control screen.
# # # # # # # # # #
I NFO
RTN
Page Up/Down for the DAB text Touch the [5] or [] button.
When all text are displayed on the information screen, [] and [5] do not appear.
Exit the Information Screen Touch [RTN] button. Return to the source control screen.
Switching to the DAB PTY Search Screen
Touch the [PTY] button.
Switching to the Language Filter Screen
Touch the [LANG] button. (page 34)
33
Other Option Control Function 7 DAB Tuner Control
Language Filter Screen
BBC BBC Na t i o n a l R1 D i g i t a l
L A N G E n g l i s h
SEARCH
RTN
Language Filter Screen
Selection the Language Touch the [2] or [3] button. Searching the Language Touch the [SEARCH] button. Exit the Language Filter Screen Touch the [RTN] button. Return to the source control screen.
34
7 External Display Control
External Display Control Screen
1 2:0 0 EXT . D I SP L AY
7 Sensor Box Control
Sensor Box Control Screen
1 2:0 0 S E N SOR NOR T H . D I R . 8
AD J UST RTN RTN
Switching the Display
Touch the [2] or [3] button.
Setting the Menu
1 Touch the [ADJUST] button. Select the item Touch the [2] or [3] button. Set the function Touch the [5] or [] button. 2 Touch the [ADJUST] button.
Exit the External Display Control Screen
Touch the [RTN] button. Return to the menu screen.
Exit the Sensor Box Control Screen
Touch the [RTN] button. Return to the menu screen.
35
Remote Control Function
Monitor Control Function
38 FM+ AM
38
SRC
SRC
FM
DISC
3 Switching the Monitor's Picture
Press the [V.SEL] button. Each time the button is pressed the monitor's picture switches.