Text preview for : GRUNDIG CUC7861.pdf part of GRUNDIG CUC7861 SM
Back to : GRUNDIG CUC7861.pdf | Home
GRUNDIG CUC 7861
Matrix
Item See Model Book
4 4 5 5 3 Service Notes (See Notes) ........................................................ Grundig G1000 Chassis X-Ray Precautions ( S e e N o t e s ) ............................................ Grundig G1000 Chassis Circuit Diagram Symbols .................................................................. Grundig CUC 1982 Remote Control Diagram ................................................................... Grundig CUC 6360 Tuner Diagram .................................................................................... Grundig CUC 5301
1
loaded in the programme memory IC840, the Luminance Delay is set to "0". The individual settings can be entered and stored with the remote control handset. Emergency Data The processor IC850 in this TV receiver is fitted with two memories in which the picture geometry data is stored. If this IC fails or the data has been changed the TV receiver must be switched on with the emergency data set. Loading the Emergency Data (eg. after changing mP IC850) Connect pin 2 of the processor to chassis and switch the TV on with the mains button. The EEPROM in the processor IC850 is loaded with: the basic data set and the geometry data for the Decoder/Sync Processor TDA 9160/9162. the basic data set for the RGB Processor TDA 4685. the AGC reference voltage (tuner gain control). the AFC reference voltage (PLL-control). 2: Settings Via the Info Menu EPROM Version Number The version number can be called up in the Info Menu with the "AUX" button. The index 05 of the part number (19798-254.05) indicates the EPROM version. Programme Lock (protection against unauthorised use) You can cancel your personal code number by pressing and OK sequentially. One place/Two Place Programme Selection Via the Menu Info Centre --> Special Functions --> Settings, Programme Selection can be switched over between 1 - 9 and 1 - 99. Maximum Programme Number Via the Menu Info Centre --> Special Functions --> Settings. When storing the channel number "00" at any programme position, programme buttons is limited to the selection with the numbers lower than this position. OSD-ON/OSD-OFF - all programmes. The on screen display can be switched on or off via the Menu Info Centre --> Special Functions --> Settings --> Pict./Sound Options. When selecting the OSD-OFF option the station identifications and scales for the analog values is switched off. Volume Offset Via the menu --> Special Functions --> Settings the volume level can be changed in 16 steps for each individual programme position. 3: Settings via the Audio Menu The following settings can be changed with the Audio Menu: - Loudspeaker: Mono/Stereo sound - Headphones: Mono/Stereo sound - Equaliser: frequencies 1 ... 12kHz - Configuration of loudspeaker boxes - Effect sounds with the IDTV button (effect sound fields menu). Switching Over the Sound (only multi system) to: Stereo, Mono, FM, NICAM, NICAM B Via the Audio Menu --> Sound. Switch the stereo decoder for the desired sound buttons. reception with FM-sound stereo broadcast: - Switchable between Stereo <--> Mono - Two-channel sound: switchable between Sound 1 <--> Sound 2. The sound for the loudspeakers and headphones can be switched over independently of each other. NICAM-sound mono broadcast: - switchable between NICAM Mono <--> FM-Mono NICAM-sound stereo broadcast: - switchable between NICAM Stereo <--> FM-Mono NICAM-sound dual-sound broadcast: - switchable to NICAM-sound 1 --> NICAM-sound 2 --> FM-Mono NICAM not relating to the picture: - switchable to NICAM-sound 1 --> NICAMsound 2 --> FM-Mono, preferred sound is FM-Mono AV mode: - Stereo (preferred setting) --> Sound 1 --> Sound 2 - With Sound 1 and Sound 2, the sound for the loudspeakers and headphones can be switched over independently of each other. 4: Settings via the Station Ident Select the menu Info Centre --> TV station Table and activate the desired TV station. OSD-ON/OSD-OFF Individual Programmes Note: only TVs with LED display. Enter a decimal point "." at the first place of the station identification. With this setting the display can be switched off for the individual programmes. The first places of the station identification can be filled with any kind of characters. Forced Switching to Mono Example: MONO Indication: ARD The stereo decoder is made to remain in the FM-Mono mode. This function is advantageous in the case of stereo broadcasts in poor reception conditions. Automatic Frequency Control AV or AF The TV tuner is automatically re-tuned according to the variations of the receiving frequency which is advantageous when feeding in the video signal via the aerial socket. Forced Switching to SECAM SECAM or SE Colour errors may occur when operating the TV with Canal-plus decoders in SECAM standard. These errors can be eliminated by forced switching to SECAM. 5: Settings via the AUX Position The "AUX" command initialises an input mode in which certain commands are interpreted differently. This mode remains active for about 4 secs. unless another command is entered. The indication "AUX" is shown on the screen for 4 secs. Changing the Display Brightness (VFD display only) Press the "AUX" button --> buttons sequentially. Setting the Peri Bit "AUX" -->" "0/AV". With the PERI-bit set, the control processor evaluates the switching voltage on pin 8 of the EURO-AV-socket AV1 (black) and switches the TV receiver to this input, eg. on descrambler operation. The Peri symbol illuminates in the display of the keyboard unit. Switching over the descrambler: - Descrambler off - Descrambler on Auto (Peri bit set) - Descrambler on Stereo (Peri bit set) - Descrambler on Mono - L (Peri bit set) - Descrambler on Mono - R (Peri bit set) Copy Function In operating mode: Select first the AV signal source eg. AV1, AV2 etc. - On: "AUX" --> "0/AV" indication "Copy on" - Off: "AUX" --> "0/AV" indication "Copy off" Copying possibilities:
From AV1(black) AV2 (orange) AV3 (blue) AV4 (CCVS-socket) AV5 (S-VHS) To --> AV2 --> AV3 --> AV2 --> AV2 --> AV2 (orange) and AV3 (blue). (blue). (orange). (orange) and AV3 (blue). (orange) and AV3 (blue).
Minimum value Optimum value Brightness 18 32 Colour contrast 24 40 B/W contrast 21 32 Volume 10 10
Alignment
All adjustment controls not mentioned in this description are adjusted during production and must not be re-adjusted in the case of repairs. 1. Chassis Board Measuring Instruments: Oscilloscope with 10:1 test probe Colour test pattern High resistance voltmeter. Checks and adjustments after replacement or repair of: Power Supply: 1.1 Horizontal Deflection: 1.2, 1.4, 1.8, 1.9 Picture Tube/CRT Panel: 1.2, 1.7 Colour-Decoder Sync. Module: 1.7 IF Amplifier, Tuner: 1.5 Tuning Module: 1.6, 1.8 Vertical Deflection: 1.9 Bridge Coil: only necessary after improper changes in the horizontal deflection adjustment 1.3 1.1: Alignment +A Voltage Preparation Set luminance to minimum. Connect the voltmeter to the cathode of D681. Alignment Process Set the control R654 to the voltage 152V. 1.2: Alignment Screen grid voltage USG Preparation Feed in a test pattern. With the remote control adjust the screen brightness so that the grey areas just become dark. Switch the TV receiver to AV operation. Connect a high-ohmic voltmeter (series resistance approx. 220 W) to the test points R, G, B and determine the maximum voltage. Alignment Process With the control SG on the picture tube panel set the maximum voltage level to approx. 165 ... 170V. If retrace lines are visible on the screen reduce the voltage by approx. 10V.
Recommended Safety Parts
Item
E72 9112 WW. 09246-188.31 09246-188.71 8300-068-696 29201-360.11 29703-291.81 8290-991-356 29201-361.17 29305-022.26 8766-701-027 09246-188.31 09246-188.71 8300-068-696 29201-360.11 29303-452.03 29703-291.32 8290-991-361 29201-361.17 8765-049-157 09246-188.71 8300-059-696 29201-360.11 29201-471.01 29303-377.03 29303-452.03 29703-291.32 8290-991-361 29201-361.19 8765-049-157 29304-050.95 09621-113.02 8531-505-221 8660-098-238 8660-098-238 8660-098-234 8515-912-063 8511-793-047 8511-793-045 29500-809.97 8306-000-012 8306-000-012 8701-230-817 8705-329-071 8735-003-068 8705-227-423 8700-329-009 8766-349-155 8311-200-010 8315-616-205 8315-616-205 8315-616-205 8315-619-028 8315-622-025 8315-623-008 8315-622-503 29201-445.97 29201-382.97 29201-030.08 09032-301.02 29201-408.97 29201-453.08 Degaussing Coil Degaussing Coil Pict. Tube A 68 KZN 696X01 CRT Socket Power Switch Power Cable Focus-UG 2 Control CRT Board CUC 7800 KSW SI A 12 OHM 5% -GA Degaussing Coil Degaussing Coil Pict. Tube A 68 KZN 696X01 CRT Socket Mains Plug - Lower Part Power Switch Power Cable Focus Control Unit MSW AX 0414-GA 3,3 MOHM Degaussing Coil Pict. Tube A 59 LCG 696X01 CRT Socket Euro-Converter Bracket Plug 2-POL Mains Plug - Lower Part Power Switch Power Cable Focus Control Unit MSW AX 0414-GA 3,3 MOHM Mains Interference Unit Fuse Holder MKT 680PF 20% 12,5KV SI-KERKO B-SS 2200PF 20% SI-KERKO B-SS 2200PF 20% SI-KERKO B-SS 1000PF 20% FKP1 0,033UF 20% 630V MP 3 0,47 UF 20% 250VW MP 0,33 UF 20% 250VW FUNKENSTOERDR OPTOKOPPLET CNY 17 F1 OPTOKOPPLET CNY 17 F1 NKS 3 4,7 OHM 5% ROE MOW LI 0411 820 OHM 5% DW 0,75W 0,68 OHM 10% MOW AX0411-GA 8,2 OHM 5% DRA 22 KSW LI 0207-NE 2,2 OHM MSW LI 0414 2,7 MOHM DUO-PTC LOET-SI.-GR 800 MA/T LOET-SI.-GR 800 MA/T LOET-SI.-GR 800 MA/T LOET-SI.-GR 1.6 A/T LOET-SI.-GR 3,15 A/T LOET-SI.-GR 4 A/T FS.3,15 A/T H 250V FOKUSIERUEBERTRAGER UEBERTRAGER EF20 DIODENSPLITTRAO KPL NETZTRAFO SPERRWANDLERTRAFO KPL SPERRWANDLERTRAFO KPL
Part No.
Description
Please take into account the following restrictions: Peri operation is not possible when AV1 is used as a signal source. Switching over to the AV2 or AV3 programme is only possible if the selected AV position and the signal source are the same. Copy function In stand-by mode: (not for OSD-TVs). Firstly select the AV signal source eg. AV1, AV2 etc. - On: "AUX" --> "0/AV" (Indication "Copy on".) - Buttons "AUX" --> " " (Indication "COP" in the display.) Copying possibilities are the same as before. Attention: In Copy Standby-Mode the switched-mode power supply is not switched off. De-activation of the copy-mode: (not for OSD-TVs). To cancel the copy mode: - Press standby or power switch off. Changing the headphone volume changes the volume level Enter "AUX" --> for headphones. Switching to mono --> stereo sound "AUX" --> activates the sound switching function: Mono --> Stereo --> Mono A --> Mono B etc. 6: IR-Data Programmer With this menu and the IR-Data Programmer 2, it is possible to transfer a maximum of 99 programme positions with the data for the TV norm, Peri, 6-place station identification, the fine tuning centre frequency and the volume offset "0". The Programmer AP transfers only channels and 4-place station identifications and the volume offset "0". Call up via the Menu Info Centre --> Special Functions --> IR-Data Programmer. Attention: The data transfer can be affected by interference's from electrical lighting fixtures. 7: Autom. Change between 4:3/16:9 Aspect Ratio With the setting "Format 4:3/16:9 auto" the aspect ratio is switched over automatically - in programme positions 1 ... 99 when the decoder is set to "ON" - in AV position or with the Peri-bit set, when a 16:9 signal source is connected to the AV1 socket. Identification: - 16:9 switching voltage at the AV1 source, Pin 8 = 6V. - 4:3 switching voltage at the AV1 source, Pin 8 = 12V. 8: Setting the Analog Values When exceeding the minimum acceptable values for the brightness, colour contrast and volume level specified in the table below, the appropriate optimum value is initialised when switching the TV on or changing from RF value AV.
R 816, R 817 ST72 760/9 WW.
R 1850 ST63 760/9
R 1850 CUC 7861
C7 C 621 C622 C 665 C 666 C 6001 C 6002 L 6001 OK637 OK646 R 503 R 520 R 525 R 551 R 552 R 665 R 6009 SI 401 SI 406 SI 411 SI 630 SI 671 SI 691 SI 6001 TR 8 TR 410 TR 526 TR 6010 TR 651 WW.
(WW. = Optional)
1.3: Alignment Bridge coil L551 Preparation The bridge coil L551 is correctly adjusted during production and should not be readjusted anymore. Call up the Service Programme --> Info Centre -> Special Functions --> Service --> Code 8500 --> Geometry. Set the horizontal amplitude to minimum. Connect channel one an oscilloscope to the collector of the transistor T572. Connect channel two of an oscilloscope between the diodes D502 and D503. Alignment Process Adjust the coil L511 so that both oscillograms have the same pulse width. Re-adjust the horizontal amplitude according to the test pattern and store.
Service Adjustments
Service and Special Functions
1: Switching-on Options ATS Reset Press and hold the L+ button on the local keyboard while switching on with the mains button to set the ATS-bit. This option activates the ATS function next time the receiver is switched on.
ATS Start Pressing the buttons "P/C" (approx. 4 secs.) --> OK (language selection menu) --> starts the Auto Tuning System (ATS). When finding a TV signal, the ATS system automatically determines the fine tuning value and the VPS signal for the station ident. Additionally for the programmes 1 ... 99 the volume offset is reset and the optimum values for brightness, colour contrast and volume level are stored together with the Peri bit for the respective country. Loading the Average Values Press and hold the "P-" button on the local keyboard and switch the TV on with the mains button. In doing so the analog average values for the programmes 1 - 99 and AV1 - AV4 are
GRUNDIG CUC 7861
Service Adjustments Cont'd.
1.4: Alignment Line sharpness Preparation Select the convergence test pattern. Contrast to maximum. Set the brightness so that the black background of the test pattern is just brightening. Alignment Process With the focus control adjust the horizontal lines for maximum sharpness. Attention: For measurements on the focusing panel use only sufficiently insulated measuring cables and test probes with adequate electric strength (eg. 100:1). 1.5: Alignment Tuner-AGC. Manual or Automatic. Preparation Manual: Feed in a standard test pattern in the upper range of the UHF band; the RF must be 1.5mV (64dBmV, noise free picture) at least. Info Centre --> Special Functions --> Service --> Code 8500 --> Tuner-AGC --> Manual. Automatic: Info Centre --> Special Functions --> Service --> Code 8500 --> Tuner-AGC --> Automatic. AFC-Reference: Info Centre --> Special Functions --> Service --> Code 8500 --> AFC-Reference. Tune to a local station on a channel as low as possible at the desired programme position with standard channel spacing without fine tuning. Not For Servicing. Alignment Process Manual: With buttons - and + tune the TV station so that noise just starts to appear in the picture. Then tune in reverse direction until the picture becomes noise free. Store with OK. Automatic: The control processor will set the optimum value for the delayed gain control voltage. Activate with button OK. AFC-Reference: On activation of AFC Reference Automatic a rectified IF-voltage is measured at the AFC output of the IF amplifier which is used on station search as a comparative value for VCRRF playback (station identification "AV") to readjust the modulator drift. Activate with OK. No function for the buttons - and +. 1.6: Alignment Colour match. Preparation Call up the programme position of the desired TV station. Info Centre --> Special Functions --> Settings ->Colour Match. Alignment Process Adjust with - and + buttons to make the signals coincide. Store with OK. 1.7: Alignment White balance Preparation Call up the White Balance menu via the Service Preparation The picture geometry is set to the last stored value whenever the receiver is switched on. Reset: Under the menu item "Reset" an average data set from the ROM IC860 is stored. After inadvertent readjustment during servicing, these basic values can be re-loaded at any time. For this, move the bar to "Reset". Press the OK button. By pressing the "AUX" button the picture geometry is set according to the "Reset" values. With the i button return to the normal menu. Programme Info Centre --> Special Functions -> Service --> Code 8500. Alignment Process With - and + set the VG and VB values so that the white rectangular area in the middle of the picture becomes achromatic. Store with OK. 1.8: Alignment Picture sharpness Preparation Call up the programme position of the desired TV station. Info Centre --> Picture Menu --> Sharpness. Alignment Process Change the value with the buttons - +. 1.9:Alignment Picture geometry Preparation Info Centre --> Special Functions --> Service --> Code 8500 --> Geometry. For accurate adjustment of the picture a test generator or standard test pattern should be used. The integrated test pattern or grid pattern may also be used. Attention: Start always with the "V-Middle" adjustment otherwise the other vertical deflection parameters would defy correct geometry adjustment. Alignment Process Via the menu, select the geometry values for the vertical deflection, then set the values for the horizontal deflection. Preparation "V-Middle" adjustment with a colour test pattern: select the "V-Middle" menu. The upper part of the picture is coloured the lower part is black and white. Alignment Process With the - or + button move the three broken lines on the left and on the right of the indication "V-Middle" upwards or downwards so that they coincide with the line separating the coloured part and B/W part of the picture. Continue with the picture geometry adjustment via the menu and store. Preparation "V-Middle" adjustment with a video generator, eg. Grundig VG 1000. Feed in the convergence test pattern with standard colour bars via RF. To store this adjustment move the bar to "Terminate with Store" and confirm with OK. Alignment Process With the - or + button change the setting so that the G-Y vector (orange area in the centre of the picture) is just covered. Continue with the picture geometry adjustment via the menu and store.
2
Trouble Shooting Guide
-Power Supply
Interference Elimination Diagram
Control Keyboard Diagram
GRUNDIG CUC 7861
3
Continued at 1
Main Diagram
GRUNDIG CUC 7861
4
Main Diagram Cont'd.
1
GRUNDIG CUC 7861
Control Unit Diagram
5
Velocity Diagram
Waveforms
CRT Diagram
GRUNDIG CUC 7861
6
Socket Diagram
GRUNDIG CUC 7861
7
Colour Decoder Sync. Diagram
GRUNDIG CUC 7861
8
DSP Diagram
GRUNDIG CUC 7861
9
Display Control Unit with Videotext Diagram
GRUNDIG CUC 7861
10
AF Output Diagram "A"
GRUNDIG CUC 7861
11
AF Output Diagram "B"
GRUNDIG CUC 7861
12
IF Amp Diagram
Continued at 2
GRUNDIG CUC 7861
13
IF Amp Diagram Cont'd
2
GRUNDIG CUC 7861
14
Tuner Diagram