Text preview for : Mitsubishi WL-82913 Chassis V23L.pdf part of Mitsubishi WL-82913 Service Manual for Mitsubishi WL-82913
Back to : Mitsubishi-WL-82913_V23L. | Home
MITSUBISHI ELECTRIC
LIQUID CRYSTAL ON SILICON PROJECTION TV V23L CHASSIS
Service Manual
MODEL
2003
WL-82913
CAUTION: Before servicing this chassis, it is important that the service person read the "SAFETY PRECAUTIONS" and "PRODUCT SAFETY NOTICE" contained in this manual.
SPECIFICATIONS
Power Input Power Usage Light Engine Light Source Frequency Range Antenna Input : AC 120V, 60Hz : 380W : 3 Liquid Crystal on Silicon ICs (LCOS) : 200W : VHF 54 ~ 470MHz UHF 470 ~ 806MHz : VHF/UHF 75 unbalanced 2 - NTSC 1 - ATV/QAM
: S-VIDEO IN JACK (Y/C separate type) Y:1.0 Vp-p C:0.286Vp-p(BURST) 75 unbalanced : COMP / Y, Cr, Cb (RCA Type) Y: 1.0 Vp-p Cr, Cb: 700mVp-p : ATV / Y(G), Pr(R), Pb(B), H, V Y: 1.0Vp-p with sync 75 (BNC) Pr, Pb: 700mV 75 H, V: 3.0Vp-p 75 : VGA / R,G,B,V,H (15 pin D) : VIDEO OUT JACK (RCA Type) 1.0Vp-p 75 unbalanced : AUDIO OUT JACK (RCA Type) -4.7dBm 4.7k unbalanced : IEEE-1394 I/O Jacks : AC-3 Digtal Audio Output : MonitorLinkTM/DVI
Cabinet Dimensions Weight 83.25""(W) x 73.75"(H) x 29.3"(D) : 519 lbs
Output Level
Speakers (8 Ohms 10W) : 2-5"x7" oval 10W midrange speakers : 2-1.5" round 10W tweeters Input Level : VIDEO IN JACK (RCA Type) 1.0Vp-p 75 unbalanced : AUDIO IN JACK (RCA Type) -4.7dBm 43k unbalanced
Digital Interface
: MonitorLinkTM Control/RS-232C
: 4 Memory Card Reader Inputs
Design specifications are subject to change without notice.
MITSUBISHI DIGITAL ELECTRONICS AMERICA, INC.
9351 Jeronimo Road, Irvine, CA 92618-1904 Copyright © 2003 Mitsubishi Digital Electronics America, Inc. All Rights Reserved
MODEL: WL-82913
CONTENTS
INTRODUCTION .................................................................................................................................. 5 PRODUCT SAFETY NOTICE ............................................................................................................... 5 SAFETY PRECAUTIONS ..................................................................................................................... 6 TV DELIVERY & INSTALLATION Cabinet Assembly ............................................................................................................................ 7 Diamond ShieldTM Installation ........................................................................................................... 9 Arc Assembly Installation .............................................................................................................. 10 USER MAINTENANCE Dust Filter Cleaning ........................................................................................................................ 12 Lamp Cartridge Replacement ......................................................................................................... 13 LAMP TROUBLESHOOTING PROCEDURE ..................................................................................... 15 DISASSEMBLY PROCEDURES Cabinet Front Disassembly ............................................................................................................ 16 Cabinet Rear Disassembly ............................................................................................................. 17 SERVICING THE DIFFUSER SCREEN AND FRESNEL LENS Removal of the Diffuser Screen and Fresnel Lens .......................................................................... 18 Installation of the Diffuser Screen and Fresnel Lens ....................................................................... 18 LIGHT BOX OPERATION (Out of the cabinet) Control Light Box Operation (KIT-RECEIVER-82913) ..................................................................... 19 Enabling Turn On ........................................................................................................................... 19 SERVICING PCBs Accessing the Chassis Removal .................................................................................................... 20 PCB Locations ............................................................................................................................... 20 DM Module Replacement ............................................................................................................... 21 ELECTRICAL ADJUSTMENTS Equipment and Initial Setup ........................................................................................................... Default Settings .............................................................................................................................. A/V Reset Defaults ........................................................................................................................ A/V Reset ...................................................................................................................................... LED Indicator Diagnostics .............................................................................................................. Remote Control Operational Mode ................................................................................................. Circuit Adjustment Mode ................................................................................................................ Service Mode Reset ....................................................................................................................... On-screen Display Position Mode .................................................................................................. E2PROM Replacement .................................................................................................................. Adjustment Items List .................................................................................................................... Adjustment Procedures Test Point Locations ............................................................................................................. Main / Sub Y Level & & HV Regulation ................................................................................. On-screen Display Position................................................................................................... Horizontal & Vertical Position ................................................................................................ 22 22 23 23 23 24 25 26 26 26 26 27 28 29 30
Page 3
MODEL: WL-82913
Optical Adjustments General Adjustment procedure .............................................................................................. Operational Preparation ........................................................................................................ Selecting and Internal Test Signal ......................................................................................... Picture Rotation Adjustment ................................................................................................. Vertical Trapezoid Distortion Adjustment ............................................................................... Horizontal Trapezoid Distortion Adjustment ...........................................................................
31 31 32 33 33 34
CHIP PARTS REPLACEMENT .......................................................................................................... 35 REPLACEMENT PARTS Parts Ordering ................................................................................................................................ Critical and Warranty Parts Designation ........................................................................................ Parts Tolerance Codes ................................................................................................................... Quick Reference List ...................................................................................................................... 36 36 36 37
SERVICE PARTS LIST ..................................................................................................................... 38 SCREEN ASSEMBLY PARTS LIST ................................................................................................... 48 CIRCUITRY BLOCK DIAGRAMS ...................................................................................................... 49
Part 2 Schematic Diagrams
CONTENTS Page SCHEMATIC DIAGRAMS PCB INTERCONNECT DIAGRAM .................................................................................................. S1 PCB-POWER / SUB-POWER ....................................................................................................... S2 PCB-TERMINAL -1 ......................................................................................................................... S3 PCB-TERMINAL 2 .......................................................................................................................... S4 PCB-SIGNAL-1 (MICRO) ................................................................................................................ S5 PCB-SIGNAL-2 (TUNER-AUDIO) ................................................................................................... S6 PCB-MLINK /E2P ........................................................................................................................... S7 PCBs-CONTROL / FRONT / PREAMP / CONNECT ...................................................................... S8 PCB-TUNER DTV........................................................................................................................... S9 PCB-DEMODULATOR.................................................................................................................. S10 PCB LAYOUT DIAGRAMS ................................................................................................................. 11
Page 4
MODEL: WL-82913
INTRODUCTION
This service manual provides service instructions for PTV Models WL-82913 which uses the V23L chassis. Service personnel should read this manual thoroughly before servicing this chassis. This service manual includes: 1. Assembly and disassembly instructions for the front and rear cabinet components. 2. Servicing of the Diffuser Screen and Fresnel Lens. 3. Servicing printed circuit boards (PCBs). 4. Electrical adjustments. 5. Optical Adjustments 6. Chip parts replacement procedures. 7. Circuit path diagrams. The parts list section of this service manual includes: 1. Cabinet and screen parts. 2. Electrical parts. Schematic and block diagrams of the above listed model are included in this service manual for better understanding of the circuitry. PCB drawings are also included for easy location of parts and test points.
PRODUCT SAFETY NOTICE
Many electrical and mechanical parts in television receivers have special safety related characteristics. These characteristics are often not evident from visual inspection nor can the protection afforded by them necessarily be obtained by using replacement components rated for higher voltage, wattage, etc. Replacement parts which have special safety characteristics are identified in this service manual. Electrical components having such features are identified by shading on the schematic diagram and by bold type in the parts list of this service manual. Therefore, the replacement for any safety part should be identical in value and characteristics.
Page 5
MODEL: WL-82913
SAFETY PRECAUTIONS
NOTICE: WARNING: 1. 2. Observe all cautions and safety related notes located inside the receiver cabinet and on the receiver chassis. Operation of this receiver outside the cabinet or with the cover removed presents a shock hazard from the receiver's power supplies. Work on the receiver should not be attempted by anyone who is not thoroughly familiar with the precautions necessary when working on high voltage equipment. When service is required, observe the original lead dress. Extra precaution should be taken to assure correct lead dress in the high voltage area. Where a short-circuit has occurred, replace those components that indicate evidence of overheating.
Leakage current check Before returning the receiver to the customer, it is recommended that leakage current be measured according to the following methods.
1. Cold Check
With the alternating current (AC) plug removed from the AC source, place a jumper across the two AC plug prongs. Connect one lead of an ohm meter to the AC plug and touch the other lead to each exposed metal part (i.e. antennas, handle bracket, metal cabinet, screw heads, metal overlay, control shafts, etc.), particularly any exposed metal part that has a return path to the chassis. The resistance of the exposed metal parts having a return path to the chassis should be a minimum of 1Mega Ohm. Any resistance below this value indicates an abnormal condition and requires corrective action.
2. Hot Check ...Use the circuit shown below to perform the hot check test.
1. Keep switch S1 open and connect the receiver to the measuring circuit. Immediately after connection, and with the switching devices of the receiver in their operating positions, measure the leakage current for both positions of switch S2. 2. Close switch S1, energizing the receiver. Immediately after closing switch S1, and with the switching devices of the receiver in their operating positions, measure the leakage current for both positions of switch S2. Repeat the current measurements of items 1 and 2 after the receiver has reached thermal stabilization. The leakage current must not exceed 0.5 milliampere (mA).
Page 6
MODEL: WL-82913
TV Delivery and Installation
Page 7
MODEL: WL-82913
Page 8
MODEL: WL-82913
DiamondShieldTM Installation and Removal
Page 9
MODEL: WL-82913
Arc Assembly Installation
Page 10
MODEL: WL-82913
Page 11
MODEL: WL-82913
Dust Filter Cleaning
Page 12
MODEL: WL-82913
Lamp Cartridge Replacement
Page 13
MODEL: WL-82913
Page 14
MODEL: WL-82913
LAMP TROUBLESHOOTING PROCEDURE
If lamp replacement does not restore operation, use the following troubleshooting procedure.
LAMP NOT LIT (Lamp Cartridge OK)
Check voltage at Pin 1 of Connector CN1, on the PCB-SUB-POWER
370VDC?
YES
Replace UNIT-POWER-LAMP
NO Check voltage across Pins 1 and 4 of Connector PL1, on the PCB-SUB-POWER
120VAC?
YES
Replace PCB-SUB-POWER
NO Replace F9A02 on PCB-POWER
Page 15
MODEL: WL-82913
CABINET DISASSEMBLY (FRONT VIEW)
*Refer to the Parts List for Part Numbers
Front Cabinet Disassembly
Remove the Speaker Grille by pulling forward. Slide the Front Panel Cover to the right (Arrow 1). Remove the Lamp Cartridge Access Cover by removing screws (A).. Remove the screws (B) securing the Front Panel Assembly, one at the top and six at the bottom. Pull the bottom of the Front Panel Assembly slightly upward, then forward, then down (Arrow 2),and then pull the Front Panel Assembly from the TV (Arrow 3). 6. Remove the screws (C) holding the Screen Assembly. 7. Pull the bottom of the Screen Assembly slighty towards the front (Arrow 4) and uplug the cables from the Control Panel. 8. While holding the bottom of the Screen Assembly away from the TV; lift the assembly upward to remove from it from the cabinet (Arrow 5). Page 16 1. 2. 3. 4. 5.
MODEL: WL-82913
CABINET DISASSEMBLY (REAR VIEW)
*Refer to the Parts List for Part Numbers
CAUTION: DO NOT tilt the Light Box when removed from the Cabinet. This can cause lamp damage and failure.
Rear Cabinet Disassembly
Remove screw (A), (B) and (C) to remove the Back Board. Remove screws (D) and remove the Sheet Top LA. Remove screws (E) to remove the Board Slide and Fan. Remove screws (F) to remove the Board Shelves. To remove the Light Box Assembly, the Lamp Box Cover must be removed (refer to page 7). Remove screws (G) holding the chassis and Light Box Assembly. Be certain that all cables and connectors between the Light Box Assembly and external items are disconnected (e.g. speaker plugs, etc.), including the USB and 1394 connectors from the Card Reader to the DM Module. 8. Slide the Light Box Assembly from the cabinet. Page 17 1. 2. 3 4. 5. 6. 7.
MODEL: WL-82913
SERVICING THE DIFFUSER SCREEN AND FRESNEL LENS
CAUTION: Wear gloves when handling the Diffuser Screen and Fresnel Lens. This prevents cuts and finger prints. Do not place Fresnel Lens in the sun. This may cause fire and heat related injuries.
Diffuser Screen and Fresnel Lens Removal
1. Remove the screen assembly shown in the Cabinet Disassembly procedure. 2. Remove the four screws (A) to remove the Screen Frame Top. 3. Carefully slide the Diffuser Screen and Fresnel Lens combination from the Screen Frame assembly. Note: When separating the Diffuser Screen from the Fresnel Lens, use caution while prying the Screen and Lens apart. Use a slot type screw driver, and remove the pressure sensitive double sided tape.
Diffuser Screen and Fresnel Lens Installation.
Note: Store the Diffuser Screen and Fresnel Lens in a cool dry place. High humidity may deform the Diffuser Screen and Fresnel Lens. 1. Apply 71.3 inches of double coated tape (Part # LENS-TAPE) along the top rear edge of the Diffuser Screen as shown below. 2. Place the Fresnel Lens on top of the Diffuser Screen and apply pressure at the top edge to bond them together as shown below. 3. Reverse the Screen Removal procedure an insert the screen in the Screen Frame Assembly.
Page 18
MODEL: WL-82913
LIGHT BOX OPERATION (Outside the cabinet)
Light Box Removal
Besides removing the Lamp Cartridge Access Cover and the items shown of page 8, several connectors have to be disconnected to remove the Light Box Assembly. Note: The Lamp Cartridge Access Cover must be re-installed after the Light Box has been removed. ES connector ... Speakers RF connector ... Preamp & Control Panel LS connector ... Control Panel CE connector ... Front Inputs 1394 & USB connectors ... Card Reader EX-F ... Exhaust Fan
CAUTION:
Only operate the Light Box with the Lamp in it's normal vertical position.
Out of Cabinet Operation
To Control Light Box Operation: Servicing Kit (part # KIT-RECEIVER 82913) must be used. The kit consists of two cables and a Remote Preamp PCB. The diagram below illustrates the kit connection to the Light Box Assembly. To Enable Turn On: After re-installing the Lamp Cartridge Access Cover, short pins 2 and 3 on the EX-F connector. The unit will not turn on if it senses a fan is uplugged or the Lamp Cartridge Access Cover is not installed.
Page 19
MODEL: WL-82913
Main Chassis
Accessing the Chassis
1. 2. 2. 3. 4. Undo the cable wire ties to the Front Panel, Speakers, etc. Unplug the Card Reader USB and 1394 cables from the top of the DM module. Remove screw (a) securing the Main Chassis. Release the Chassis Locks on each side of the chassis. Carefully slide the Chassis to the rear of the unit.
PCB Locations
Page 20
MODEL: WL-82913 DM Module Replacement
1. Unplug the Card Reader USB and 1394 cables from the DM module, and refer to the Chassis Removal Procedure to slide the chassis towards the rear of the set. 2. Remove screws (a), to remove the DM Rear Panel, Figure 1. 3. Remove screws (a) and (b) to remove the DM Module Cover, Figure 2. 3. Remove the E2P module from the original DM and plug it into the replacement DM. 5. Plug the DM module securely into the PCB-DTV-TUNER. 6. Check operation before installing the DM Cover, Figure 3. · Insert insulation (cardboard) between the Demodulator Ground Spring and the DM. · Plug the set in and check the operation. · If O.K., uplug the set and install the DM Cover.
Figure 1: DM Rear Panel
Figure 2: DM Module Cover
Figure 3: Checking new DM Operation
Page 21
MODEL: WL-82913
ELECTRICAL ADJUSTMENTS
Note: Perform only the adjustments required. Do not attempt an alignment if proper equipment is not available.
Test Equipment
· · · Oscilloscope (Unless otherwise specified, use 10:1 probes) Signal Generator (both SD and HD capable) Electrical Tools 1) Composite Video Signal Signal Level :1.0Vp-p () Video :0.714Vp-p Sync :0.286Vp-p Burst :-.286Vp-p 2) Component Signal (YPbPr) Y level :1.0Vp-p (75) Video :0.7Vp-p Sync :0.3Vp-p Pb, Pr Signal Level :0.7Vp-p 3) RGB Signal R, G & B :0.7Vp-p () HD & VD :TTL level
Test Signal
Initial Setup
A. Option Menu Setup
Follow the steps below for the initial set-up: 1. Select the "MENU" display by pressing the "MENU" button once. 2. Press the number buttons "0", "3", "7", "0" in sequence to select the "OPTION MENU" display. 3. Press the "ADJUST" button to select "INITIAL." 4. Press "ENTER." NOTE: At this time channel 3 is automatically selected.
(MENU-0-3-7-0) OPTION MENU Initial Power restore DTV Port
:OFF :Auto
B.
Default Settings MAIN MENU DEFAULT SETTINGS
Time Day CAPTIONS Analog Captions Background Digital Captions Digital Settings Appearance Digital Channel Guide V-CHIP LOCK V-CHIP TV Rating FV-Fantasy Violence D-Sexual Dialog L-Adult Language S-Sexual Situation V-Violence Program not Rated Movie Rating V-Chip Time Start Time Stop Time Lock By Time Lock by Time Lock Time Unlock Time Front Button Lock AUDIO/VIDEO SETTINGS A/V Memory Reset Audio Volume Bass Treble Balance 12:00 AM Monday With Mute Gray With Mute Default Off Off TV-PG (3) Enabled (3) Enabled (3) Enabled (3) Enabled (3) Enabled (3) Enabled PG 12:00 AM 12:00 AM Off NA NA Off Ant-A 30% 50% 50% 50% Surround Listen to Level Sound TV Speakers Audio 2 Out Video Contrast Brightness Sharpness Color Tint Color Temp. Video Noise Image Type TV Define EDGE Auto Position (PC only) Horiz. Position (PC only) Vert. Position (PC only) Side by Side Contrast (PC Side by Side only) Black Boarder Video Mute Black Enhancement Advanced Color Balance PerfectColorTM A/V Memory for Ant-A PIP/POP Source PIP Position POP Position PIP/POP Format Format Off Stereo Off On Main 100% 50% 50% 50% 50% High Standard Video On ... Center Center 100% Off On On Manual All Centered Ant A Ch 3 Lower Right Right Half Dble. Window Stretched
SETUP Edit Setup Review (3) Enabled Antenna A (3) Enabled Antenna B (3) Enabled Input DTV (3) Enabled Input 1 (3) Enabled Input 2 (3) Enabled Input 3 (3) Enabled Component 1 (3) Enabled Component 2 (3) Enabled Antenna DTV (3) Enabled VGA (3) Enabled MonLink (3) Enabled Card 1 (3) Enabled Card 2 (3) Enabled Card 3 (3) Enabled Card 4 Icon Position As above Ant-A, Ant-B, Ant-DTV, ComFlash MemStick, SmartMed, MMC& SD Input-1, Input-2, Input-3, Comp-1, Comp-2, Input DTV, VGA, MonLink, Cards 1...4 On Transport Menu Energy Mode Standard Language English ANTENNA Antenna ANT A Memorize Channels Air Channel Ch-3 Memory Deleted TIME Clock Setting Manual
Page 22
MODEL: WL-82913
A/V RESET DEFAULT SETTINGS (By Input) INPUTS Compon. Ant A/B Ant DTV Inp-DTV VGA 1/2/3 1/2 Max. Max. Max. Max. Max. Max. Center Center Center Center Center Center Center Center Center Center Center N/A Center Center Center Center Center Center Center Center Center Center Center Center High High High High High High Standard N/A Standard Standard Standard N/A Video N/A Video Video Video N/A On On On On On On Center Center Center Center Center Center Center Center Center Center Center Center Center Center Center Center Center Center OFF OFF OFF OFF OFF OFF Stereo English N/A N/A N/A N/A OFF OFF OFF OFF OFF OFF
A/V Memory Contrast Brightness Sharpness Color Tint Color Temp. Video Noise Image Type VSM Sharpness Bass Treble Balance Surround Listen To Level Sound
1394 MonLink 1/2/3 Max. Max. Center Center Center Center Center Center Center Center High High N/A Standard N/A Video On On Center Center Center Center Center Center OFF OFF N/A N/A OFF OFF
Card 1~4 Max. Center Center Center Center High N/A N/A On Center Center Center OFF N/A OFF
NOTE: Front panel AV Reset... resets all AV Memory Settings User Menu AV Reset ... only resets the selected AV Memmory
C. A/V Memory
Each of the external inputs has its' own Audio/Video Memory. A change in an A/V setting at a specific input is stored in memory for that specific input.
D. A/V Reset
1. The front panel AV Reset button initializes all A/V Memories. 2. The AV Reset in the user's menu initializes only the selected input's A/V Memory.
LED Indicator Diagnostics
The front panel LEDs provide an indication of the sets operation, and the possible cause of a malfunction. There are three front panel LEDs, "Power", "Status" and "Lamp". Which LED is lit, the color and whether it is blinking or steady indicate the current status, or a possible malfunction.
1. LED Designations (Normal Conditions)
Normal Conditions TV Off (Standby) Lamp Standby Power On Power ON to Standby mode (Fan operating) Booting up after AC applied On Timer Set LEDs POWER STATUS Off Off Green (fast Off blink) Green Off Green (fast Off blink) Green (fast Off blink) Green (slow blink) Off LAMP Off Off Off Off Off Off
Page 23
MODEL: WL-82913
2. LED Designations (Abnormal Conditions)
Abnormal Conditions Temperature Hot (Check Air Filter) Lamp usage over 3000 hours Lamp Cover is open No Lamp Installed POWER Off _ Off Off LEDs STATUS Yellow Off Off Off Off Red Red LAMP Off Yellow Yellow (blinking) Yellow (blinking) Red Off Off
Lamp Failed to turn On (or broken) Off Fan stopped Off Circuit Failure (short problem) Off · Status LED ....Excess Temperature or Circuit problem · Lamp LED ... Lamp Status · Yellow ... "Warning" · Red ... "More Serious Warning"
3. Error Code Operational Check
Note: The TV must be in "Shut Down" and not have been switched Off, to perform the Error Code Operational Check. When the TV is switched Off, the code automatically resets to "12" No Error. Pressing the front panel "DEVICE" and "MENU" buttons at the same time, and holding for 5 seconds, activates the Error Code Mode. The LED flashes denoting a two digit Error Code, or indicating no problem has occured since the last Initalization. Note: The front panel buttons must be used, NOT those on the Remote Control.
· · · ·
The number of flashes indicates the value of the MSD (tens digit) of the Error Code. The flashing then pauses for approximately 1/2 second. The LED then flashes indicating the value of the LSD (ones digit) of the Error Code. The Error Code is repeated a total of 5 times. Example: If the Error Code is "23", the LED will flash two times, pause, and then flash three times.
4. Error Codes
The Error Code designations indicating malfunction, or no malfunction, are listed below:
Press and Hold "DEVICE" and "MENU" FOR 5 SECONDS Error Code Probable Cause 12 No error detected 22 Recovery from momentery Reset 31 Lamp not detected 32 Lamp Cover open 34 Lamp abnormality 35 Fan failed 38 Excess Lamp Temperature 39 Excess LCOS Temperature 41 Short Detected 42 Excess PCS Temperature 43 Driver Temperature or Voltage abnormal
Remote Control Operational Modes
There are two Remote Hand Unit Operational Modes, "Standard" and "NetCommandTM". The Remote is initially in the "Standard" mode. The "NetCommandTM" mode is used when controlling Home Theater devices using NetCommandTM. To change the Remote Operational Mode: · Set the Remote to the TV Layer · Point the Remote away from the TV. · To change to "NetcommandTM" ... Hold the "Power" button and press "9-3-5" in sequence. · To change to "Standard" ... Hold the "Power" button and press "0-0-0" in sequence. Page 24
MODEL: WL-82913
Circuit Adjustment Mode
Most of the adjustments can only be performed using the remote hand unit. Many of the adjustments must be performed in both the 480i and 1080i modes. Video/Color adjustments must be performed in the 480i and 1080i modes, and data must be preset in the 480P (DVD) and VGA modes. Note: Set the Remote Operational Mode to "NetCommandTM". (Hold the "Power" button and press "9-3-5" in sequence.) This slows the remote's response and makes adjustments easier. When adjustments are complete, set the Remote to its' original Operational Mode. (Hold the "Power" button and press "0-0-0" in sequence)
A. Activating the Circuit Adjustment Mode
The current signal source determines if the activated Adjustment Mode is 480i or 1080i. 1. Select the signal source (480i or 1080i). 2. Press the "MENU" button on a remote hand unit. 3. Press the number buttons "0", "3", "5", "7" in sequence. The screen will change to the Adjustment Mode. Note: Repeat steps 1 and 2 if the circuit adjustment mode does not appear on screen.
CHASSIS FUNCTION ADJ ITEM
V23L DECODER 1 22 SCNT 16 480i
ABBREV. DATA SIGNAL
B. Selection of adjustment Functions and Adjustment Items
To select an adjustment item in the circuit adjustment mode, first select the adjustment function that includes the specific adjustment item to be selected. Then select the adjustment item. Refer to the following pages for the listing of adjustment functions and adjustment items. 1. Press the "AUDIO" button on a remote hand unit to select an adjustment function. Each time the button is pressed, the Function changes in the following sequence:
Adjustment Functions Decoder-1 Aki
2. Press the "VIDEO" button to select a specific Adjustment Item. The Item number increases each time the "VIDEO" button is pressed.
Decoder-2
C. Changing Data
After selecting an adjustment Item, use the "ADJUST UP/DOWN" buttons to change data. · Press "ADJUST DOWN" to decrease the data value. · Press "ADJUST UP" to increase the data value.
D. Saving Adjustment Data
Press "ENTER" to save adjustment data in memory. The character display turns red for approximately one second in this step. Note: If the circuit adjustment mode is terminated without pressing "ENTER", changes in adjustment data are not saved. Page 25
MODEL: WL-82913
E. Terminating the Circuit Adjustment Mode
Press the "MENU" button on the remote hand unit twice to terminate the adjustment mode. Note: The circuit adjustment mode can also be terminated by turning power OFF.
F. Service Mode Reset
To reset items in the Service Mode to their factory values: 1. Press MENU-0-3-5-7 to enter the Service Mode. 2. Press the "0,1,2,3," insequence to Reset to the Factory settings.
On Screen Display Position Adjustment Mode
Activation
1. 2. Select 480i or 1080i source. Press MENU-0-3-8-8
E2PROM Replacement
Service Data is stored on the PCB-E2P located on the DM assembly. When replacing the DM assembly, retaining the original PCB-E2P will eliminate the need for any realignment. The following tables are provided as a guide in case of total data loss.
List of Adjustment Items.
DECODER-1 Item # 22 24 Abbrev. SCNT SCLR Description Y-Out Amplitude Cb/Cr Out Amplitude Range 0~31 0~31 NTSC 14 13 MENU-0-3-5-7 Component 480i 480p 1080i RGB 16 16 16 16 16 16 16 16 MENU-0-3-5-7 Component 480i 480p 1080i RGB 12 12 12 12 13 13 13 13
DECODER-2 Item # 22 24 Abbrev. SCNT SCLR Description Y-Out Amplitude Cb/Cr Out Amplitude Range 0~31 0~31 NTSC 12 13
Aki
Item # 1 2 3 4 5 6 7 8 9 10 11 12 13 14 Abbrev. TPAT HPOS VPOS RGB CONT R-HI G-HI B-HI R-LO G-LO B-LO TPCR TPCG TPCB Description Test Pattern Horizontal Position Vertical Position RGB Ouput Setting Main AD contrast R value (hi-temp) G value (hi temp) B value (hi temp) R value (lo-temp) G value (lo temp) B value (lo temp) Test pattern Red level Test pattern Green level Test pattern Blue level
MENU-0-3-5-7 Range Data 1~22 0 160 35 0~3 0 0~255 79 0~127 255 0~127 255 0~127 255 0~127 255 0~127 255 0~127 255 0~255 64 0~255 64 0~255 64
OSD Horizontal Centering Abbrev. Description OSDSD OSD Horizontal Position for SD
MENU-O-3-8-8 Range Data 0~960 135
Page 26
MODEL: WL-82913
Adjustment Test Points
Test Points
JA pin 26 ......... Main Y Gain JA pin 28 ......... Main Color Level JA pin 35 ......... Sub Y Gain JA pin 37 ......... Sub Color Level
Page 27
MODEL: WL-82913
[Video Circuit] 1. Main/Sub Y Gain
Measuring Instrument Test Point Ext. Trigger Measuring Range Input Signal Input Terminal Oscilloscope JA pins 26 & 35 -----50mV/Div ColorBars (100% White level) Video Input (1 or 2)
Purpose: Symptom:
To set picture luminance. Excessive or insufficient brightness.
1. 2. 3. 4. 5. 6. 7. 8. 9.
Supply a color bar signal to Video Input 1 or 2 (not an RF input). Select the color bar signal as the source for both main and sub pictures. Connect an oscilloscope to connector JA pin 26 (Main-Y) Activate the Circuit Adjust Mode. Select item "22 SCNT" in the Decoder-1 function. Adjust the data between 0.71 Vp-p max. and 0.66 Vp-p min. at JA pin 26. Move oscilloscope to JA pin 35 (Sub-Y) Select item "22 SCNT" in the Decoder-2 function. Adjust data so the Sub-Y signal equals Main-Y (+0.0V -0.06V).
CIRCUIT ADJUST MODE Activate ........ MENU-0-3-5-7 Function .................AUDIO Ite m N o . .................VIDEO Adjus t Data ...........ADJUST Save Data .... .........ENTER Exit ..............MENU (twice)
[Audio Circuit] 2. Main/Sub Color Level
Measuring Instrument Test Point Ext. Trigger Measuring Range Input Signal Input Terminal Oscilloscope JA pins 28 & 37 -----50mV/Div Color Bars Video Input (1 or 2)
Purpose: Symptom:
To match sub picture color to that of the main picture. Main and sub pictures colors differ.
. 1. 2. 3. 4. 5. 6. 7. 8. 9.
Supply a color bar signal to Video Input 1 or 2 (not an RF input). Select the color bar signal as the source for both main and sub pictures. Connect an oscilloscope to connector JA pin 28 (Main-Pb) Activate the Circuit Adjust Mode. Select item "24 SCLR" in the Decoder-1 function. Adjust the data between 0.71 Vp-p max. and 0.66 Vp-p min. at JA pin 28. Move oscilloscope to JA pin 37 (Sub-Pb) Select item "24 SCLR" in the Decoder-2 function. Adjust data so the Sub-Y signal equals Main-Y (+0.0V -0.06V).
CIRCUIT ADJUST MODE Activate ........ MENU-0-3-5-7 Function .................AUDIO Ite m N o . .................VIDEO Adjus t Data ...........ADJUST Save Data .... .........ENTER Exit ..............MENU (twice)
Main-Pb
Page 28
MODEL: WL-82913
[On Screen Display] 12.Character Position
Measuring Instrument Test Point Ext. Trigger Measuring Range Input Signal Input Terminal ------------------Video Signal (NTSC) ANT-A
Purpose: Symptom:
To position the character display horizontally. Incorrect display position
1. 2. 3. 4.
Supply an NTSC signal to Ant-A and select Ant-A as the source. Enter the OSD Position Mode, press "MENU-0-3-8-8". Adjust "OSDSD" to center the OSD horizontally. Press "MENU" to save data and exit the mode.
Page 29
MODEL: WL-82913
[High Voltage Circuit] 3. Horizontal/Vertical Position
Measuring Instrument Test Point Ext. Trigger Measuring Range Input Signal Input Terminal -----------------None Comp-1 / DTV
Purpose: Symptom:
To center picture on the screen. Picture is off center.
Alignment for all inputs except Ant-DTV 1. Select the Component-1 Input, no signal. 2. Enter the Service Adjustment Mode. 3. Select Item "1 TPAT" in the Aki Function. 4. Select "1 (FRAME 1)" pattern. 5. Select Item "2 HPOS" 6. Center the picture horizontally, and press "Enter". 7. Select "3 VPOS" and center the picture vertically. 8. Press "Enter". 9. Press "Menu" twice to terminate the Adjustment Mode.
CIRCUIT ADJUST MODE Activate ........ MENU-0-3-5-7 Function .................AUDIO Item No. .................VIDEO Adjust Data ...........ADJUST Save Data .... .........ENTER Exit ..............MENU (twice)
Alignment for the Ant-DTV Input only. 1. Select the Ant DTV Input, no signal. 2. Enter the Service Adjustment Mode. 3. Select Item "1 TPAT" in the Aki Function. 4. Select "1 (FRAME 1)" pattern. 5. Select Item "2 HPOS" 6. Center the picture horizontally, and press "Enter". 7. Select "3 VPOS" and center the picture vertically. 8. Press "Enter". 9. Press "Menu" twice to terminate the Adjustment Mode.
Page 30
MODEL: WL-82913
OPTICAL UNIT ADJUSTMENTS
General Adjustment Procedure
1. Loosen the locking screw (brass) for the specific adjustment. 2. Rotate that adjustment adjusting screw (black) to perform the adjustment. 3. After adjusting, tighten the locking screws.
Operational Preparations
Lamp Bracket Preparations
Loosen The 6 Locking Screws (A through F) in the Lamp Box Support Bracket, refer to Figure 1.
Page 31
MODEL: WL-82913
Screen Preparation
1. Attach masking tape to the center of each side of the screen frame. (Fig.2) 2. Mark the center of the each side of the screen frame over the tape with a pen. (Fig.2)
Selecting Internal Test Signals
1. Press the buttons "MENU", "0", "3", "5" "7" in order. 2. Select Item "1 TPAT" in the AKi function. 3. Select "1 (FRAME 1)" test pattern. The adjustment signal in Fig. 3 is displayed on the screen.
Page 32
MODEL: WL-82913
Picture Rotation Adjustment
Refer to Fig. 4 1. Slightly loosen the two Locking Screws (1). 2. Use (A-1) to adjust rotations 3. Tighten the two Locking Screws (1).
Adjusting Vertical Trapezoid Distortion
Refer to Fig. 5 1. Slightly loosen the two Locking Screws (2) 2. Use (A-2) to adjust Vertical Trapezoid Distortion. NOTE: If the picture moves horizontally, use the electrical Horiz. Position adjustment to recenter the picture. 3) Tighten the two Locking Screws (2).
Page 33
MODEL: WL-82913
Adjusting Horizontal Trapezoid Distortion
Refer to Fig. 6 1. Slightly loosen the three Locking Screws (3) 2. Use (A-3) to adjust Horizontal Trapezoid Distortion. NOTE: If the picture moves vertically, use the electrical Vertical Position adjustment to recenter the picture. 3) Tighten the three Locking Screws (3).
Page 34
MODEL: WL-82913
CHIP PARTS REPLACEMENT
Some resistors, shorting jumpers (0 Ohm resistors), ceramic capacitors, transistors and diodes are chip parts. The following precautions should be taken when replacing these parts. Cautions: 1. Use a fine tipped, well insulated soldering iron (approximately 30 watts), and tweezers. 2. Melt the solder and remove the chip parts carefully so as not to tear the copper foil from the printed circuit board. 3. Discard removed chips; do not reuse them. 4. Do not apply heat for more than 3 (three) seconds to new chip parts. 5. Avoid using a rubbing stroke when soldering. 6. Take care not to scratch, or damage the chip parts when soldering. 7. Supplementary cementing is not required. Chip Parts Removal (Resistors, Capacitors, etc.) 1. Grasp the part with tweezers. Melt the solder at both sides alternately, and remove one side of the part with a twisting motion. 2. Melt the solder at the other side and remove the part. Chip Parts Removal (Transistors) 1. Melt the solder of one lead and lift the side of that lead upward. 2. Simultaneously melt the solder of the other two leads and lift the part from the PCB.
Replacement 1. Presolder the contact points on the circuit pattern. 2. Press the part downward with tweezers and apply the soldering iron as shown.
PAGE 35
MODEL: WL-82913
REPLACEMENT PARTS
Parts Ordering To expedite delivery of replacement parts orders, specify the following: 1. Model Number/Serial Number 2. Part Number and description 3. Quantity Note: Unless complete information is supplied, delay in processing of orders will result. Critical and Warranty Parts Designation Critical Electrical Components are indicated by Bold Type in the Parts List, and in the schematic diagrams by shading. Warranty Return Parts are indicated in the Parts List with an (*). Parts Tolerance Codes Refer to the following chart for tolerance characteristics of electrical components.
MARK Tolerance %
B ± 0.1
C ± 0.25
D ± 0.5
F ±1
G ±2
J ±5
K ± 10
MARK Tolerance %
M ± 20
N ± 30
V ± 10
X + 40 -20
Z + 80 -20
P + 100 -0
Q + 30 -10
MARK Tolerance (pF)
M ± 0.1
N ± 0.25
V ± 0.5
X ±1
Z ±2
PAGE 36
MODEL: WL-82913
QUICK REFERENCE FOR COMMON REPLACEMENT PARTS
PART DESCRIPTION
SCREENS LENS-FRESNEL - 82" SCREEN-DIFFUSER - 82" DIAMOND SHIELD - 82" PCBs PCB-CONTROL PCB-DEMOD PCB-DM PCB-DTVTUNER PCB-E2P PCB-FORMATTER PCB-FRONT PCB-LCOS-INTERCONNECT PCB-MEMORY-CARD PCB-MLINK PCB-POW E R PCB-PREAMP PCB-SIGNAL PCB-SUB-POWER PCB-TERMINAL
PART NUMBER
491P169010 491P168010 KIT-WL82913 DS
935D748001 934C066001 934C067004 934C105001 934C061001 930B908001 935D749001 934C069001 299P271010 930D059002 930B906001 935D733008 930B905008 930B913001 934C060008
PART DESCRIPTION
OPTICAL UNIT LAMP-CARTRIDGE LAMP-POW E R-UNIT SENSOR-LAMP TEMPERATURE FANS FAN-COMBINER
FAN-EXHAUST/LAMP-PWR
PART NUMBER
939P953010 915P016010 939P954010 299C050010
FAN-FORMATTER FAN-ILLUMINATION FAN-LAMP REMOTE CONTROL - V22+/V23 ARC PARTS DOW E L-PIN (ARC) TAP-SCREW (ARC) S e rvice Operation Kit
299C038010 299P103060 299P103050 299C037010 299C039010 290P117010
689D006010 669D140070
KIT-RECEIVER 82913
PAGE 37
MODEL: WL-82913
[#] Model Legend: [a] WL-82913 Ref # Part # Part Name & Description [#] Ref # IC7I01 IC7K21 IC7M01 IC8A00 IC8A01 IC8A04 IC8B05 IC8D01 IC8D02 IC8D03 IC8D05 IC8E02 IC8F02 IC8F05 IC8F12 IC8F13 IC8F14 IC8F15 IC8FA1 IC8FA2 IC8FA3 IC8FA4 IC9A20 IC9A51 IC9B04 IC9C21 IC9C22 IC9C23 IC9C24 IC9C25 IC9D00 IC9D03 IC9D04 IC9D05 IC9F01 IC9F02 Part # 271P006010 270P831010 271P006010 270P818020 270P915020 275P278010 270P915020 275P982010 275P982010 275P982010 275P982010 275P883010 275P657050 274P503020 261P135010 270P991010 270P915020 275P124040 275P124040 275P124040 275P124040 275P124040 267P164010 267P140020 270P879010 270P928010 270P677010 270P677020 270P677010 270P677030 270P668020 267P076030 267P076030 270P816010 275P967010 270P995010 Part Name & Description IC - NJM2580M IC-C-MOS - OPA2350PA IC - NJM2580M IC - CXA3506R IC - RT9161A-33CG IC-C-MOS - TC74LVX14FT IC - RT9161A-33CG IC - MT48LC2M32B2-7 IC - MT48LC2M32B2-7 IC - MT48LC2M32B2-7 IC - MT48LC2M32B2-7 IC-C-MOS - THC63LVDM83R IC-C-MOS - 24LC256T-I/SN IC-C-MOS - 74ACT245MTC FET-HEX - IRF7313 IC - IRU3037CS IC - RT9161A-33CG IC-C-MOS - SN74LVC245APWR IC-C-MOS - SN74LVC245APWR IC-C-MOS - SN74LVC245APWR IC-C-MOS - SN74LVC245APWR IC-C-MOS - SN74LVC245APWR HIC - TNY264P HIC - STR-F6628 IC - SC1566IM-2.5 IC - BA17809FP IC - BA033FP IC - BA05FP IC - BA033FP IC - BAO9FP IC - SI-8050S HIC - SI-3050C HIC - SI-3050C IC - NJM431L IC-C-MOS - FA5502P IC - NJM78L20A [#]
INTEGRATED CIRCUITS
IC2A00 IC2A95 IC2B00 IC2C00 IC2D00 IC2D01 IC2D02 IC2D03 IC2E00 IC2E20 IC2E65 IC2F00 IC2F10 IC2G00 IC2H01 IC2K00 IC2L00 IC2S01 IC3A01 IC3E01 IC5200 IC5251 IC5252 IC5253 IC52A0 IC52A1 IC52A2 IC53A1 IC53A2 IC53A3 IC5409 IC54K2 IC54K3 IC54K6 IC54K7 IC54Z1 IC54Z3 IC54Z4 IC55A6 IC55A7 IC55A8 IC55E1 IC55E3 IC5602 IC5I01 IC7000 IC7001 IC7002 IC7003 IC7A00 IC7B00 IC7B01 IC7B20 IC7C30 IC7C50 IC7C70 IC7C80 IC7C85 275P937010 270P994010 275P937010 275P989010 270P974010 275P981010 261P135010 270P677010 275P947010 272P379020 270P992020 276P021010 270P677020 276P021010 275P937010 270P623010 270P623010 271P004010 275P731020 270P750010 270P677030 270P988010 270P877010 270P877010 275P715020 275P662020 270P806030 275P888010 275P888010 275P888010 275P464010 270P880010 270P880010 270P880010 270P880010 275P657050 275P657050 270P880010 275P741020 275P741020 275P741020 275P464010 275P679010 279P069030 271P006010 275P943060 271P023010 271P023010 271P023010 275P942090 271P023010 271P023010 275P533010 263P154010 275P419010 270P706020 270P677010 270P677020 IC-C-MOS - MM1519XQ IC - MAX4550CAI IC-C-MOS - MM1519XQ IC-C-MOS - MAX3223ECAP IC-C-MOS - SII907B IC-C-MOS - 24LCS22AT/SN FET-HEX - IRF7313 IC - BA033FP IC-C-MOS - UPD64083 IC - LM1881MX (NSC) IC - BA25BC0FP IC-C-MOS - TA1340AF IC - BA05FP IC-C-MOS - TA1340AF IC-C-MOS - MM1519XQ IC - CXA2069Q IC - CXA2069Q IC - CM1208-08MS IC-C-MOS - MSP3445G-QI-B8-V3 IC - LA4663 IC - BAO9FP IC-OP AMP - LM358M IC - UPC3217GV IC - UPC3217GV IC-C-MOS - BCM3510KPF P22 IC-C-MOS - CY7C1019CV33-15 IC - SI-3018LSA IC-C-MOS - MT48LC16M16A2TG IC-C-MOS - MT48LC16M16A2TG IC-C-MOS - MT48LC16M16A2TG IC-C-MOS - TC7WH14FK IC - 24LC64I/SN IC - 24LC64I/SN IC - 24LC64I/SN IC - 24LC64I/SN IC-C-MOS - 24LC256T-I/SN IC-C-MOS - 24LC256T-I/SN IC - 24LC64I/SN IC-C-MOS - MT48LC8M16A2TG IC-C-MOS - MT48LC8M16A2TG IC-C-MOS - MT48LC8M16A2TG IC-C-MOS - TC7WH14FK IC-C-MOS - TC74LCX74FT IC - SN74LVTH244APW IC - NJM2580M IC-C-MOS - PIC18F252 IC - SN74CBTD1G125DBVR IC - SN74CBTD1G125DBVR IC - SN74CBTD1G125DBVR IC-C-MOS - M306V3FGFP IC - SN74CBTD1G125DBVR IC - SN74CBTD1G125DBVR IC-C-MOS - M24C64WM6T IC-C-MOS - SN74HC132DB IC-C-MOS - SN74AHCT1G126DBV IC - MAX823REUK IC - BA033FP IC - BA05FP
TRANSISTORS
CHIP Type Transistors (Listed by Part No.) Part No. Description 260P806010 DTA124EK/UN2112 260P807030 DTC124EKAT146 260P809010 DTC114YK 260P817030 2SA1037K-S 260P817050 2SA1037K-R,S/2SB709AI-R,S 260P817080 2SA1037K-R,S 260P818030 2SC2412K-S 260P818050 2SC2412K-R,S/2SD601AI-R,S 260P818080 2SC2412K-R,S 260P836090 2SC3326-A,B 260P846030 DTC143ZKAT146 Ref # Q5250 Q7C51 Q7C66 Q7K21 Q9A00 Conventional Part # 261P026010 261P114010 261P114010 260C004010 260C004010 Transistors (By Ref #) Part Name & Description TR - 2SC3356 TR - 2SA1585STPR TR - 2SA1585STPR TR - 2SC1740S-R,S/2SC3311A-R,S TR - 2SC1740S-R,S/2SC3311A-R,S [#]
PAGE 38
MODEL: WL-82913
[#] Model Legend: [a] WL-82913 Ref # Q9A20 Q9A21 Q9D00 Q9D01 Q9D02 Q9D03 Q9D04 Q9D05 Q9D06 Q9D07 Q9D10 Q9D11 Q9D12 Q9D13 Q9D14 Q9D15 Q9D18 Q9D19 Q9D20 Q9D21 Q9F01 Q9F02 Q9F03 Part # 260C004010 260C004010 260C004010 260C004050 261P101010 260C603010 261P101010 260C004010 261P101010 260C004010 260C604010 260C604010 260C604010 260C604010 260C604010 260C604010 260C604010 260C604010 261P101010 260C004010 261P110010 260P325010 260P741010 Part Name & Description TR - 2SC1740S-R,S/2SC3311A-R,S TR - 2SC1740S-R,S/2SC3311A-R,S TR - 2SC1740S-R,S/2SC3311A-R,S TR - 2SA933S-R,S/2SA1309A-R,S TR - PHP21N06T TR - DTA124ES/UN4112 TR - PHP21N06T TR - 2SC1740S-R,S/2SC3311A-R,S TR - PHP21N06T TR - 2SC1740S-R,S/2SC3311A-R,S TR - DTC124ES/UN4212 TR - DTC124ES/UN4212 TR - DTC124ES/UN4212 TR - DTC124ES/UN4212 TR - DTC124ES/UN4212 TR - DTC124ES/UN4212 TR - DTC124ES/UN4212 TR - DTC124ES/UN4212 TR - PHP21N06T TR - 2SC1740S-R,S/2SC3311A-R,S TR - FS22SM-10 TR - 2SC2655-O,Y TR - 2SA1020-0,Y [#] Ref # D9A57 D9A58 D9B01 D9D01 D9D02 D9D03 D9D04 D9D05 D9D06 D9D07 D9D08 D9D09 D9D10 D9D11 D9D12 D9D13 D9D17 D9D18 D9D25 D9D27 D9F01 D9F02 D9F03 D9F04 D9F05 D9F06 D9F07 Part # 264P045080 264P045080 264P828010 262P094010 264P590010 264P614010 262P115010 264P045080 264P045080 264P045080 264P045080 264P045080 264P045080 264P045080 264P469090 264P484030 264P880010 264P470040 264P488030 264P045080 262P031010 264P527020 264P825040 264P825040 264P825040 264P590010 262P064010 Part Name & Description DIODE - 1S2076A/1S2471OM DIODE - 1S2076A/1S2471OM D-CHIP - DAN202U/MA142WK DIODE - FME-230A DIODE - EL1Z DIODE - FMB-36 DIODE - FMX-22S DIODE - 1S2076A/1S2471OM DIODE - 1S2076A/1S2471OM DIODE - 1S2076A/1S2471OM DIODE - 1S2076A/1S2471OM DIODE - 1S2076A/1S2471OM DIODE - 1S2076A/1S2471OM DIODE - 1S2076A/1S2471OM DIODE - EQA02-28C/RD30EB2 DIODE - RD5.6FB2 DIODE - RK46 DIODE - EQA02-30C/RD33EB1 DIODE - RD13FB2 DIODE - 1S2076A/1S2471OM DIODE - D6SB80 DIODE - AK04 DIODE - ERA15-08 DIODE - ERA15-08 DIODE - ERA15-08 DIODE - EL1Z DIODE - SF10L604 [#]
DIODES
D2D28 D2J91 D2L80 D2L81 D5280 D52A0 D5401 D5405 D7513 D7K21 D7K22 D7L20 D7L21 D7L22 D7L23 D8B01 D8B02 D8B04 D8F00 D8F01 D8F03 D8F11 D9A00 D9A02 D9A03 D9A04 D9A20 D9A21 D9A22 D9A23 D9A24 D9A54 D9A55 D9A56 262P805050 262P075010 262P075010 262P075010 262P089010 262P071070 262P071070 262P802010 264P826010 268P100010 264P045080 262P075010 264P212020 264P584020 264P584020 264P882010 264P882010 264P828010 264P828010 264P828010 262P090010 264P878010 262P031010 264P825040 264P461050 264P045080 264P045080 264P463090 264P724010 264P045080 264P045080 264P652010 264P527020 264P045080 D-CHIP - UDZS5.1B DIODE - RSB6.8S DIODE - RSB6.8S DIODE - RSB6.8S DIODE - MA2S728 DIODE-LE - SML-210FT DIODE-LE - SML-210FT D-CHIP - 1SS302 DIODE-CHIP - DA204K DIODE-PHOTO - SFH235FA DIODE - 1S2076A/1S2471OM DIODE - RSB6.8S D-LED - LN31GPH DIODE-LE - SML1216W-C,D DIODE-LE - SML1216W-C,D D-CHIP - HSB123 D-CHIP - HSB123 D-CHIP - DAN202U/MA142WK D-CHIP - DAN202U/MA142WK D-CHIP - DAN202U/MA142WK DIODE - M1FP3 DIODE-CHIP - HZM27WA DIODE - D6SB80 DIODE - ERA15-08 DIODE - EQA02-06B/RD5.6EB3 DIODE - 1S2076A/1S2471OM DIODE - 1S2076A/1S2471OM DIODE - EQA02-09D/RD10EB1 DIODE - STF14 DIODE - 1S2076A/1S2471OM DIODE - 1S2076A/1S2471OM DIODE - UF4007F DIODE - AK04 DIODE - 1S2076A/1S2471OM
COILS
L1A09 L1A30 L1A31 L1B09 L1B30 L1B31 L2A14 L2A28 L2A90 L2A95 L2B04 L2B28 L2C03 L2D07 L2D08 L2D09 L2D13 L2D17 L2D18 L2D19 L2D23 L2D24 L2D26 L2D27 L2D31 L2D32 L2D37 L2D70 L2E00 L2E10 409P923060 321C114010 409P923060 409P923060 321C114010 409P923060 409P777080 409P777080 409P777080 409P777080 409P777080 409P777080 325C146090 409P777080 409P777080 409P777080 409P777080 409P777080 409P777080 409P777080 409P777080 409P777080 409P777080 409P777080 409P777080 409P777080 409P777080 409P777080 409P777080 325C146000 EMI-F-CHIP - BLM21B272S COIL-RF - 2200MH-J EMI-F-CHIP - BLM21B272S EMI-F-CHIP - BLM21B272S COIL-RF - 2200MH-J EMI-F-CHIP - BLM21B272S EMI-F-CHIP - BLM21P221S EMI-F-CHIP - BLM21P221S EMI-F-CHIP - BLM21P221S EMI-F-CHIP - BLM21P221S EMI-F-CHIP - BLM21P221S EMI-F-CHIP - BLM21P221S COIL-CHIP - 33MH-J EMI-F-CHIP - BLM21P221S EMI-F-CHIP - BLM21P221S EMI-F-CHIP - BLM21P221S EMI-F-CHIP - BLM21P221S EMI-F-CHIP - BLM21P221S EMI-F-CHIP - BLM21P221S EMI-F-CHIP - BLM21P221S EMI-F-CHIP - BLM21P221S EMI-F-CHIP - BLM21P221S EMI-F-CHIP - BLM21P221S EMI-F-CHIP - BLM21P221S EMI-F-CHIP - BLM21P221S EMI-F-CHIP - BLM21P221S EMI-F-CHIP - BLM21P221S EMI-F-CHIP - BLM21P221S EMI-F-CHIP - BLM21P221S COIL-CHIP - 5.6MH-J
PAGE 39
MODEL: WL-82913
[#] Model Legend: [a] WL-82913 Ref # L2E20 L2E31 L2E38 L2E46 L2F01 L2F25 L2F40 L2F60 L2F80 L2G01 L2G25 L2G50 L2G70 L2G71 L2G72 L2H01 L2H04 L2H28 L2H51 L2J70 L2K42 L2L42 L2L80 L2L81 L2L82 L2L83 L2L84 L2L85 L3A10 L3A49 L5105 L5115 L51P3 L51P3 L51P4 L51P4 L5200 L5201 L5202 L5203 L5204 L5205 L5206 L5207 L5208 L5250 L5253 L5256 L52A0 L52A1 L52A2 L52A3 L52A4 L5301 L5302 L5400 L5401 L5402 L5403 L5404 Part # 409P777080 409P777080 409P777080 409P777080 409P777080 409P777080 325C146030 325C146030 325C146030 409P777080 409P777080 325C146030 409P777080 325C462020 325C462020 409P923060 409P923060 409P923060 409P923060 325C146030 409P777080 409P777080 409P923060 409P923060 409P923060 409P923060 409P923060 409P923060 409P923060 409P923060 351P216010 351P216010 409P777080 409P777080 409P777080 409P777080 325C142050 325C240050 325C240050 325C240050 325C240050 409P956020 409P956020 409P956020 409P956020 325C144090 325C140040 409P956010 409P777080 409P777080 409P956010 409P956010 325C240050 409P777080 409P777080 409P955020 409P955020 409P955020 409P955020 409P955020 Part Name & Description EMI-F-CHIP - BLM21P221S EMI-F-CHIP - BLM21P221S EMI-F-CHIP - BLM21P221S EMI-F-CHIP - BLM21P221S EMI-F-CHIP - BLM21P221S EMI-F-CHIP - BLM21P221S COIL-CHIP - 10MH-J COIL-CHIP - 10MH-J COIL-CHIP - 10MH-J EMI-F-CHIP - BLM21P221S EMI-F-CHIP - BLM21P221S COIL-CHIP - 10MH-J EMI-F-CHIP - BLM21P221S COIL-PEAKING - 56MH-K COIL-PEAKING - 56MH-K EMI-F-CHIP - BLM21B272S EMI-F-CHIP - BLM21B272S EMI-F-CHIP - BLM21B272S EMI-F-CHIP - BLM21B272S COIL-CHIP - 10MH-J EMI-F-CHIP - BLM21P221S EMI-F-CHIP - BLM21P221S EMI-F-CHIP - BLM21B272S EMI-F-CHIP - BLM21B272S EMI-F-CHIP - BLM21B272S EMI-F-CHIP - BLM21B272S EMI-F-CHIP - BLM21B272S EMI-F-CHIP - BLM21B272S EMI-F-CHIP - BLM21B272S EMI-F-CHIP - BLM21B272S COIL-CH-CHIP - 857CM-0009 COIL-CH-CHIP - 857CM-0009 EMI-F-CHIP - BLM21P221S EMI-F-CHIP - BLM21P221S EMI-F-CHIP - BLM21P221S EMI-F-CHIP - BLM21P221S COIL-CHIP - 100MH-K/J COIL-CHIP - 2.2MH-M COIL-CHIP - 2.2MH-M COIL-CHIP - 2.2MH-M COIL-CHIP - 2.2MH-M EMI-F-CHIP - BLM18AG221S EMI-F-CHIP - BLM18AG221S EMI-F-CHIP - BLM18AG221S EMI-F-CHIP - BLM18AG221S COIL-CHIP - 0.68MH-M -OR-K COIL-CHIP - 1.8MH-M -OR-K-OR-J EMI-F-CHIP - BLM18PG121S EMI-F-CHIP - BLM21P221S EMI-F-CHIP - BLM21P221S EMI-F-CHIP - BLM18PG121S EMI-F-CHIP - BLM18PG121S COIL-CHIP - 2.2MH-M EMI-F-CHIP - BLM21P221S EMI-F-CHIP - BLM21P221S EMI-F-CHIP - BLM18BB220SN1 EMI-F-CHIP - BLM18BB220SN1 EMI-F-CHIP - BLM18BB220SN1 EMI-F-CHIP - BLM18BB220SN1 EMI-F-CHIP - BLM18BB220SN1 [#] Ref # L5406 L5407 L5470 L5471 L5472 L5473 L5474 L5475 L5476 L54A0 L54A0 L54A1 L54A1 L54A4 L54A4 L54A5 L54A5 L54A6 L54A6 L54D0 L54D1 L54D3 L5571 L5573 L55A0 L55A1 L55A2 L55A3 L55A4 L55C0 L55C0 L55E3 L55E4 L55E5 L55E6 L55E7 L55F1 L55F2 L55F3 L55F4 L55F5 L55F6 L55F7 L55F8 L55F9 L55G1 L5601 L5602 L56C0 L56D0 L56D1 L5901 L5903 L5905 L5907 L5907 L5908 L5908 L5910 L5910 Part # 409P955020 409P955020 409P955020 409P955020 409P955020 409P955020 409P955020 409P955020 409P955020 409P777080 409P777080 409P777080 409P777080 409P777080 409P777080 409P777080 409P777080 409P777080 409P777080 409P955020 409P955020 409P955010 409P956020 409P956020 409P777080 409P777080 409P777080 409P777080 409P777080 409P777080 409P777080 409P955020 409P955020 409P955020 409P955020 409P955020 409P955020 409P955020 409P955020 409P955020 409P955020 409P955020 409P955020 409P955020 409P955020 409P955020 325C141030 325C141030 325C141030 409P955020 409P955020 325C241050 409P777080 325C141030 409P777080 409P777080 409P777080 409P777080 409P777080 409P777080 Part Name & Description EMI-F-CHIP - BLM18BB220SN1 EMI-F-CHIP - BLM18BB220SN1 EMI-F-CHIP - BLM18BB220SN1 EMI-F-CHIP - BLM18BB220SN1 EMI-F-CHIP - BLM18BB220SN1 EMI-F-CHIP - BLM18BB220SN1 EMI-F-CHIP - BLM18BB220SN1 EMI-F-CHIP - BLM18BB220SN1 EMI-F-CHIP - BLM18BB220SN1 EMI-F-CHIP - BLM21P221S EMI-F-CHIP - BLM21P221S EMI-F-CHIP - BLM21P221S EMI-F-CHIP - BLM21P221S EMI-F-CHIP - BLM21P221S EMI-F-CHIP - BLM21P221S EMI-F-CHIP - BLM21P221S EMI-F-CHIP - BLM21P221S EMI-F-CHIP - BLM21P221S EMI-F-CHIP - BLM21P221S EMI-F-CHIP - BLM18BB220SN1 EMI-F-CHIP - BLM18BB220SN1 EMI-F-CHIP - BLM18BB221SN1 EMI-F-CHIP - BLM18AG221S EMI-F-CHIP - BLM18AG221S EMI-F-CHIP - BLM21P221S EMI-F-CHIP - BLM21P221S EMI-F-CHIP - BLM21P221S EMI-F-CHIP - BLM21P221S EMI-F-CHIP - BLM21P221S EMI-F-CHIP - BLM21P221S EMI-F-CHIP - BLM21P221S EMI-F-CHIP - BLM18BB220SN1 EMI-F-CHIP - BLM18BB220SN1 EMI-F-CHIP - BLM18BB220SN1 EMI-F-CHIP - BLM18BB220SN1 EMI-F-CHIP - BLM18BB220SN1 EMI-F-CHIP - BLM18BB220SN1 EMI-F-CHIP - BLM18BB220SN1 EMI-F-CHIP - BLM18BB220SN1 EMI-F-CHIP - BLM18BB220SN1 EMI-F-CHIP - BLM18BB220SN1 EMI-F-CHIP - BLM18BB220SN1 EMI-F-CHIP - BLM18BB220SN1 EMI-F-CHIP - BLM18BB220SN1 EMI-F-CHIP - BLM18BB220SN1 EMI-F-CHIP - BLM18BB220SN1 COIL-CHIP - 10MH-K COIL-CHIP - 10MH-K COIL-CHIP - 10MH-K EMI-F-CHIP - BLM18BB220SN1 EMI-F-CHIP - BLM18BB220SN1 COIL-CHIP - 15MH-K EMI-F-CHIP - BLM21P221S COIL-CHIP - 10MH-K EMI-F-CHIP - BLM21P221S EMI-F-CHIP - BLM21P221S EMI-F-CHIP - BLM21P221S EMI-F-CHIP - BLM21P221S EMI-F-CHIP - BLM21P221S EMI-F-CHIP - BLM21P221S [#]
PAGE 40
MODEL: WL-82913
[#] Model Legend: [a] WL-82913 Ref # L5911 L5911 L5912 L5912 L5913 L59A0 L59A1 L59A1 L59E0 L59E0 L59L0 L59M1 L59R0 L59R2 L59R3 L59T0 L59T1 L59T2 L59X0 L5I14 L7000 L7005 L7006 L7502 L7A90 L7A99 L7B20 L7B91 L7C00 L7C63 L7C64 L7C65 L7C66 L7C70 L7C80 L7C81 L7C82 L7I14 L7K01 L7M14 L8A00 L8A01 L8A02 L8A03 L8A04 L8A06 L8A07 L8A08 L8A09 L8A10 L8A11 L8B01 L8B02 L8B03 L8B04 L8B06 L8B07 L8B08 L8B09 L8B10 Part # 409P777080 409P777080 409P777080 409P777080 409P777080 409P777080 409P777080 409P777080 409P777080 409P777080 409P923060 325C141090 325C141030 325C141030 325C141030 409P777080 409P777080 409P777080 325C140050 409P777050 325C240050 325C140010 325C140010 325C142050 409P777050 409P923060 409P777080 409P777050 409P923060 409P876040 409P876040 409P876040 409P876040 409P923060 409P777050 409P923060 409P923060 409P777050 325C121030 409P777050 409P777080 325C241030 409P777080 409P777080 409P777080 409P865060 409P865060 409P865040 409P865040 409P865040 409P777080 409P865040 409P865040 409P865060 409P865060 325C241030 409P865020 409P865020 325C241030 409P865020 Part Name & Description [#] Ref # L8B11 L8B12 L8B13 L8B14 L8B15 L8B16 L8B18 L8B19 L8B20 L8B21 L8B22 L8BB1 L8BB2 L8C01 L8C02 L8C03 L8D00 L8D01 L8D02 L8D03 L8D04 L8D05 L8D06 L8D08 L8D09 L8D10 L8EA1 L8EA2 L8EA3 L8EA4 L8EA5 L8EA6 L8EA7 L8EB1 L8EB2 L8EB3 L8EB4 L8EB5 L8EB6 L8F00 L8F01 L8F02 L8F03 L8F04 L8F05 L8F06 L8F07 L8F08 L8F09 L8F11 L8F12 L8F13 L8F14 L8F15 L8F16 L8F17 L8F18 L8F19 L8F20 L8F21 Part # 409P865020 409P865020 409P865020 409P865020 409P865060 409P865060 409P865060 409P865060 409P865040 409P865040 409P865040 409P865020 409P865020 409P777080 409P777080 409P777080 409P777080 409P777080 409P777080 409P777080 409P777080 409P777080 409P777080 409P777080 409P777080 409P865020 409P777080 409P777080 409P777080 409P777080 409P777080 409P777080 409P777080 409P777080 409P777080 409P777080 409P777080 409P777080 409P777080 409P865060 409P865060 409P777080 409P865060 409P865060 409P865060 409P865060 409P865060 409P865060 409P865060 409P865060 409P865060 409P865060 409P865060 409P777080 321C140060 321C140060 351P250010 321C140060 409P777080 409P777080 Part Name & Description EMI-F-CHIP - BLM11A601S EMI-F-CHIP - BLM11A601S EMI-F-CHIP - BLM11A601S EMI-F-CHIP - BLM11A601S EMI-F-CHIP - BLM11B141S EMI-F-CHIP - BLM11B141S EMI-F-CHIP - BLM11B141S EMI-F-CHIP - BLM11B141S EMI-F-CHIP - BLM11B050SA EMI-F-CHIP - BLM11B050SA EMI-F-CHIP - BLM11B050SA EMI-F-CHIP - BLM11A601S EMI-F-CHIP - BLM11A601S EMI-F-CHIP - BLM21P221S EMI-F-CHIP - BLM21P221S EMI-F-CHIP - BLM21P221S EMI-F-CHIP - BLM21P221S EMI-F-CHIP - BLM21P221S EMI-F-CHIP - BLM21P221S EMI-F-CHIP - BLM21P221S EMI-F-CHIP - BLM21P221S EMI-F-CHIP - BLM21P221S EMI-F-CHIP - BLM21P221S EMI-F-CHIP - BLM21P221S EMI-F-CHIP - BLM21P221S EMI-F-CHIP - BLM11A601S EMI-F-CHIP - BLM21P221S EMI-F-CHIP - BLM21P221S EMI-F-CHIP - BLM21P221S EMI-F-CHIP - BLM21P221S EMI-F-CHIP - BLM21P221S EMI-F-CHIP - BLM21P221S EMI-F-CHIP - BLM21P221S EMI-F-CHIP - BLM21P221S EMI-F-CHIP - BLM21P221S EMI-F-CHIP - BLM21P221S EMI-F-CHIP - BLM21P221S EMI-F-CHIP - BLM21P221S EMI-F-CHIP - BLM21P221S EMI-F-CHIP - BLM11B141S EMI-F-CHIP - BLM11B141S EMI-F-CHIP - BLM21P221S EMI-F-CHIP - BLM11B141S EMI-F-CHIP - BLM11B141S EMI-F-CHIP - BLM11B141S EMI-F-CHIP - BLM11B141S EMI-F-CHIP - BLM11B141S EMI-F-CHIP - BLM11B141S EMI-F-CHIP - BLM11B141S EMI-F-CHIP - BLM11B141S EMI-F-CHIP - BLM11B141S EMI-F-CHIP - BLM11B141S EMI-F-CHIP - BLM11B141S EMI-F-CHIP - BLM21P221S COIL-RF - 2.7MH-M COIL-RF - 2.7MH-M COIL-CHOKE - GSTC6018-100M COIL-RF - 2.7MH-M EMI-F-CHIP - BLM21P221S EMI-F-CHIP - BLM21P221S [#]
EMI-F-CHIP - BLM21P221S EMI-F-CHIP - BLM21P221S EMI-F-CHIP - BLM21P221S EMI-F-CHIP - BLM21P221S EMI-F-CHIP - BLM21P221S EMI-F-CHIP - BLM21P221S EMI-F-CHIP - BLM21P221S EMI-F-CHIP - BLM21P221S EMI-F-CHIP - BLM21P221S EMI-F-CHIP - BLM21P221S EMI-F-CHIP - BLM21B272S COIL-CHIP - 33MH-K COIL-CHIP - 10MH-K COIL-CHIP - 10MH-K COIL-CHIP - 10MH-K EMI-F-CHIP - BLM21P221S EMI-F-CHIP - BLM21P221S EMI-F-CHIP - BLM21P221S COIL-CHIP - 2.2MH-M/K/J EMI-F-CHIP - BLM21B201S COIL-CHIP - 2.2MH-M COIL-CHIP - 1MH-M COIL-CHIP - 1MH-M COIL-CHIP - 100MH-K/J EMI-F-CHIP - BLM21B201S EMI-F-CHIP - BLM21B272S EMI-F-CHIP - BLM21P221S EMI-F-CHIP - BLM21B201S EMI-F-CHIP - BLM21B272S EMI-F-CHIP - CNF20C221S/CKD510JB1H221S EMI-F-CHIP - CNF20C221S/CKD510JB1H221S EMI-F-CHIP - CNF20C221S/CKD510JB1H221S EMI-F-CHIP - CNF20C221S/CKD510JB1H221S EMI-F-CHIP - BLM21B272S EMI-F-CHIP - BLM21B201S EMI-F-CHIP - BLM21B272S EMI-F-CHIP - BLM21B272S EMI-F-CHIP - BLM21B201S COIL-PEAKING - 10MH-K EMI-F-CHIP - BLM21B201S EMI-F-CHIP - BLM21P221S COIL-CHIP - 10MH-K EMI-F-CHIP - BLM21P221S EMI-F-CHIP - BLM21P221S EMI-F-CHIP - BLM21P221S EMI-F-CHIP - BLM11B141S EMI-F-CHIP - BLM11B141S EMI-F-CHIP - BLM11B050SA EMI-F-CHIP - BLM11B050SA EMI-F-CHIP - BLM11B050SA EMI-F-CHIP - BLM21P221S EMI-F-CHIP - BLM11B050SA EMI-F-CHIP - BLM11B050SA EMI-F-CHIP - BLM11B141S EMI-F-CHIP - BLM11B141S COIL-CHIP - 10MH-K EMI-F-CHIP - BLM11A601S EMI-F-CHIP - BLM11A601S COIL-CHIP - 10MH-K EMI-F-CHIP - BLM11A601S
PAGE 41
MODEL: WL-82913
[#] Model Legend: [a] WL-82913 Ref # L8F22 L8F23 L8F24 L8F25 L8F26 L8F31 L8F32 L8F33 L8F34 L8F35 L8F36 L8F37 L8F38 L8F39 L8F41 L8F42 L8F43 L8F44 L9A00 L9A01 L9A02 L9A05 L9A06 L9A20 L9A54 L9A55 L9A56 L9B02 L9B02 L9B03 L9B03 L9B05 L9B05 L9B06 L9B06 L9B07 L9B07 L9B09 L9B09 L9B10 L9B10 L9B11 L9B11 L9B13 L9B13 L9B14 L9B14 L9B15 L9B15 L9B24 L9D00 L9D01 L9D02 L9D03 L9D04 L9D05 L9D06 L9D07 L9D08 L9D09 Part # 409P865060 409P777080 409P777080 409P865060 409P865060 409P777080 409P777080 409P777080 409P777080 409P777080 409P777080 409P777080 409P777080 409P777080 409P777080 409P777080 409P777080 409P777080 351P203010 351P203010 351P223010 351P079010 351P079010 321C141070 411D021010 411D021010 411D021010 321C140060 321C140060 321C140060 321C140060 409P777080 409P777080 409P777080 409P777080 409P777080 409P777080 409P777080 409P777080 409P777080 409P777080 409P777080 409P777080 409P777080 409P777080 409P777080 409P777080 409P777080 409P777080 409P957010 321C141030 321C141010 321C141010 351P226010 321C141030 321C140060 321C141070 321C141030 321C141030 321C141030 Part Name & Description EMI-F-CHIP - BLM11B141S EMI-F-CHIP - BLM21P221S EMI-F-CHIP - BLM21P221S EMI-F-CHIP - BLM11B141S EMI-F-CHIP - BLM11B141S EMI-F-CHIP - BLM21P221S EMI-F-CHIP - BLM21P221S EMI-F-CHIP - BLM21P221S EMI-F-CHIP - BLM21P221S EMI-F-CHIP - BLM21P221S EMI-F-CHIP - BLM21P221S EMI-F-CHIP - BLM21P221S EMI-F-CHIP - BLM21P221S EMI-F-CHIP - BLM21P221S EMI-F-CHIP - BLM21P221S EMI-F-CHIP - BLM21P221S EMI-F-CHIP - BLM21P221S EMI-F-CHIP - BLM21P221S FILTER-LINE - SS35V-45022 FILTER-LINE - SS35V-45022 FILTER-LINE - SLF15N0601 CHOKE-COIL - SN12-500J CHOKE-COIL - SN12-500J COIL-RF - 22MH-K CORE-FERRITE - L5 R3.6 CORE-FERRITE - L5 R3.6 CORE-FERRITE - L5 R3.6 COIL-RF - 2.7MH-M COIL-RF - 2.7MH-M COIL-RF - 2.7MH-M COIL-RF - 2.7MH-M EMI-F-CHIP - BLM21P221S EMI-F-CHIP - BLM21P221S EMI-F-CHIP - BLM21P221S EMI-F-CHIP - BLM21P221S EMI-F-CHIP - BLM21P221S EMI-F-CHIP - BLM21P221S EMI-F-CHIP - BLM21P221S EMI-F-CHIP - BLM21P221S EMI-F-CHIP - BLM21P221S EMI-F-CHIP - BLM21P221S EMI-F-CHIP - BLM21P221S EMI-F-CHIP - BLM21P221S EMI-F-CHIP - BLM21P221S EMI-F-CHIP - BLM21P221S EMI-F-CHIP - BLM21P221S EMI-F-CHIP - BLM21P221S EMI-F-CHIP - BLM21P221S EMI-F-CHIP - BLM21P221S EMI-F-CHIP - NFE61PT102E1H9 COIL-RF - 10MH-K COIL-RF - 6.8MH-M COIL-RF - 6.8MH-M COIL-CHOKE - D1512C4-V 150UH COIL-RF - 10MH-K COIL-RF - 2.7MH-M COIL-RF - 22MH-K COIL-RF - 10MH-K COIL-RF - 10MH-K COIL-RF - 10MH-K [#] Ref # L9D11 L9F02 L9F03 LC2C02 LC2C03 LC2C07 Part # 321C140060 351P079020 351P079020 409P876020 409P876020 409P876020 Part Name & Description COIL-RF - 2.7MH-M CHOKE-COIL - SN13-500 CHOKE-COIL - SN13-500 EMI-F-CHIP - CNF20C470S/CKD510JB1H470S EMI-F-CHIP - CNF20C470S/CKD510JB1H470S EMI-F-CHIP - CNF20C470S/CKD510JB1H470S [#]
TRANSFORMERS
T9A20 T9A50 T9F01 350P796010 350P808010 350P767010 TRANS-PWR - ETS19AB1M3AG TRANS-PWR - ETS7983-39 TRANS - DC-08068-5
RESISTORS
CHIP Type Resistors (Listed by value) Part No. Value Part No. 103P509050 1/16W 0OHM 103P492050 103P488000 1/4W 1-J 103P502050 103P509000 1/16W 6.8-J 103P502060 103P500010 1/16W 10-J 103P492090 103P793030 1/16W 22-F 103P502070 103P500050 1/16W 22-J 103P502080 103P400050 1/8W 22-J 103P493020 103P793040 1/16W 24-F 103P493030 103P500060 1/16W 27-J 103P502090 103P500070 1/16W 33-J 103P503000 103P910070 1/16W 33-J 103P493060 103P500070 1/16W 33-J 103P503010 103P500080 1/16W 39-J 103P493090 103P500090 1/16W 47-J 103P503020 103P844030 1/16W 56-D 103P494010 103P501000 1/16W 56-J 103P503030 103P401000 1/8W 56-J 103P494020 103P501010 1/16W 68-J 103P503040 103P794060 1/16W 75-F 103P503050 103P509090 1/4W 75-J 103P494070 103P794070 1/16W 82-F 103P503060 103P501020 1/16W 82-J 103P49