Text preview for : WM-FX888.pdf part of Sony WM-FX888 Service Manual for Sony Stereo Cassette Player (Walkman) WM-FX888.
Back to : WM-FX888.pdf | Home
WM-FX888
SERVICE MANUAL
Ver 1.0 2001.11
E Model Chinese Model Tourist Model
Manufactured under license from Dolby Laboratories. "Dolby" and the double-D symbol are trademarks of Dolby Laboratories.
Model Name Using Similar Mechanism Tape Transport Mechanism Type
WM-FX675 MF-WMFX671-162
SPECIFICATIONS
Radio section
Frequency range FM: 87.5 - 108 MHz AM: 530 - 1 710 kHz (North, Central, and South America) 531 - 1 602 kHz (other countries)
Battery life (Approx. hours)
Sony alkaline LR6 (SG)** Tape playback Radio reception 36 32
(JEITA*)
Tape section
Frequency response (Dolby NR off) Playback: 40 - 15 000 Hz Output Headphones (i) jack Load impedance 8 - 300
Rechargeable battery (NC-6WM) Tape playback Radio reception Sony alkaline LR6 (SG)** and Rechargeable NC-6WM Tape playback Radio reception 45 42 10 10
General
Power requirements 1.5 V Rechargeable battery One R6 (size AA) battery Dimensions (w/h/d) Approx. 108.4 × 77.7 × 23.0 mm (43/8 × 31/8 × 29/32 inches) Mass Approx. 160 g (5.7 oz) Supplied accessories · AC power adaptor (1) · Battery case (1) · Stereo headphones or earphones with remote control (1) · Charging stand (1) · Rechargeable battery (NC-6WM, 1.2 V, 600 mAh, Ni-Cd) (1) · Rechargeable battery carrying case (1) · Carrying pouch (1) Design and specifications are subject to change without notice.
* Measured value by the standard of JEITA (Japan Electronics and Information Technology Industries Association). (Using a Sony HF series cassette tape) **When using a Sony LR6 (SG) "STAMINA" alkaline dry battery (produced in Japan). Note · The battery life may be shorter depending on the operating condition, the surrounding temperature and battery type.
RADIO CASSETTE PLAYER
9-873-396-01
2001K0500-1 C 2001.11
Sony Corporation
Personal Audio Company Published by Sony Engineering Corporation
WM-FX888
TABLE OF CONTENTS 1. 2. 3.
3-1. 3-2. 3-3. 3-4. 3-5. 3-6. 3-7. 3-8. 3-9. 3-10.
SERVICING NOTES ............................................... 3 GENERAL ................................................................... 5 DISASSEMBLY
Disassembly Flow ........................................................... Case Section .................................................................... MAIN Board ................................................................... Belt (F2) .......................................................................... Motor (Capstan/Reel) (M601) ........................................ Cassette Lid Sub Assy ..................................................... Reel Ornament Block Assy ............................................. Holder (F) Assy (/M) ...................................................... Pinch Lever (RA)/(NA) Assy ......................................... Magnetic Head (Playback) (HP901) .............................. 6 6 7 7 8 8 9 9 10 10
Note on the AC power adaptor Use only the supplied AC power adaptor. Do not use any other AC power adaptor.
Polarity of the plug
Notes on chip component replacement · Never reuse a disconnected chip component. · Notice that the minus side of a tantalum capacitor may be damaged by heat. Flexible Circuit Board Repairing · Keep the temperature of the soldering iron around 270 °C during repairing. · Do not touch the soldering iron on the same conductor of the circuit board (within 3 times). · Be careful not to apply force on the conductor when soldering or unsoldering.
4. 5. 6.
MECHANICAL ADJUSTMENTS ....................... 11 ELECTRICAL ADJUSTMENTS ......................... 11 DIAGRAMS
13 14 15 16 17 18 19 21
6-1. Block Diagram TUNER Section ............................. 6-2. Block Diagram MAIN Section ................................ 6-3. Note for Printed Wiring Board and Schematic Diagrams ................................................ 6-4. Printed Wiring Board MAIN Board (Side A) ......... 6-5. Printed Wiring Board MAIN Board (Side B) ......... 6-6. Schematic Diagram MAIN Board (1/2) .................. 6-7. Schematic Diagram MAIN Board (2/2) .................. 6-8. IC Pin Function Description ...........................................
7.
7-1. 7-2. 7-3. 7-4. 7-5. 7-6.
EXPLODED VIEWS
Case Section .................................................................... Chassis Section ............................................................... Main Section ................................................................... Mechanism Deck Section-1 (MF-WMFX671-162) ....... Mechanism Deck Section-2 (MF-WMFX671-162) ....... Mechanism Deck Section-3 (MF-WMFX671-162) ....... 23 24 25 26 27 28
8.
ELECTRICAL PARTS LIST ............................... 29
SAFETY-RELATED COMPONENT WARNING!! COMPONENTS IDENTIFIED BY MARK 0 OR DOTTED LINE WITH MARK 0 ON THE SCHEMATIC DIAGRAMS AND IN THE PARTS LIST ARE CRITICAL TO SAFE OPERATION. REPLACE THESE COMPONENTS WITH SONY PARTS WHOSE PART NUMBERS APPEAR AS SHOWN IN THIS MANUAL OR IN SUPPLEMENTS PUBLISHED BY SONY.
2
WM-FX888 SECTION 1 SERVICING NOTES
This set detects the rotation of the idler gear (A) (side S) using the PH1 (photo reflector). The PH1 is mounted on the MAIN board, therefore the idler gear (A) (side S) cannot be detected with the MAIN board removed. As a result, the motor (M601) cannot be controlled, causing malfunction. Further, the DIRECTION switch (S1) is also mounted on the MAIN board, and with the board removed, the mechanism position cannot be detected and the operation is not changed over. Therefor, when the voltage check is executed with the MAIN board removed, follow the procedure provided below. 1. Setting (1) Refer to "3. DISASSEMBLY", and remove the MAIN board. (2) Connect the MAIN board to the motor (M601) and the plunger (PM901) using jumper wires. These can be connected easily with the use of the extension tool (Part No. 1-769143-11) (ten in one set). (3) Short the TAPE DETECT switch (S901-1) terminals and the ATS switch (S901-2) terminals. (4) Connect the AF oscillator to the Q15-1 (COLLECTOR) and the TP23 (GND). (5) Supply 1.3 V to the battery terminals using the regulated power supply. 2. Preset state To set the PLAY, FF, REW modes, the preset state must be set. (1) Check that the slider (NR) and the DIRECTION switch (S1) are set to the center position. If not, set the preset state as follow. (2) Move the DIRECTION switch (S1) to the side, which the slider (NR) is facing. (3) The slider (NR) will move when the regulated power supply switch is set to OFF once and then set to ON. Move the DIRECTION switch (S1) according to this timing and set to the center position.
MAIN Board (side B) TAPE DETECT (S901-1) ATS (S901-2)
3. (1) (2) (3) (4)
FF, REW modes Check that the preset state is set. Input the square wave or sine wave to the Q15-1 (COLLECTOR) and the TP23 (GND). Press the [x RADIO OFF] button (S3) to set the STOP mode. Press the [+ FF] button (S4) or the [-- REW] button (S5).
4. PLAY mode (1) Check that the preset state is set. (2) Input the square wave or sine wave to the Q15-1(COLLECTOR) and the TP23 (GND). (3) Press the [x RADIO OFF] button (S3) to set the STOP mode. (4) Press the [Y REPEAT] button (S9) will move the slider (NR) once towards the side R and then to the side F. Move the DIRECTION switch (S1) according to this timing will set the PLAY mode (side F). Press the [Y REPEAT] button (S9) another time and move the DIRECTION switch (S1) according to the movement of the slider (NR) will set the PLAY (R mode).
Note 1: If the above fails, perform from preset again. Note 2: Use the [Y REPEAT] (S9), [x RADIO OFF] (S3), [+ FF] (S4), and [-- REW] (S5) buttons on the remote controller as much as possible. If no remote controller, do not touch the buttons with your hands, but using a stick with a round tip. Note 3: When using headphones, the timing for move the DIRECTION switch (S1) can be determined from the beep sound.
connect to the plunger (PM901) square wave AF oscillator (sine wave) 10 Hz, 3.5 dB
+
battery terminal #
battery terminal 3
+ FF (S4) REW (S5) Y REPEAT (S9) x RADIO OFF (S3) PH1
Q15
S1 DIRECTION FWDTSTOPtREV
TP23 (GND)
connect to the motor (M601)
3
WM-FX888
Slider (NR)
Rotation system
Rotation system during PLAY.
gear (NR) (FWD : left side/ REV : right side) idler gear (A) (side S) idler gear (A) (side T) gear (REEL) (side S) gear (REEL) (side T) motor pulley
slider (NR)
cam gear
side F side R center
gear (Y)
clutch assy (F) idler gear (B)
reverse pulley insert flywheel (N) insert flywheel (R)
Rotation system during FF.
Rotation system during REW.
idler gear (A) (side T) gear (REEL) (side T) cam gear
gear (FR) (FF: left side) motor pulley
gear (FR) idler gear (A) (REW: right side) (side S) gear (REEL) (side S) motor pulley cam gear
clutch assy (F) gear (Y)
gear (Y)
clutch assy (F)
reverse pulley insert flywheel (N) insert flywheel (R)
reverse pulley insert flywheel (N) insert flywheel (R)
4
WM-FX888 SECTION 2 GENERAL
A C
E
TUNE/PRESET + TUNE/PRESET RADIO OFF + BAND· RADIO ON
This section is extracted from instruction manual.
MENU
SET
B
F
ENTER
RADIO ON/ BAND·OFF
CHARGE
HOLD SOUND HOLD SET MENU MODE
D
FWD (forward) side REV (reverse) side
G
Terminals Terminals Terminals
FF (AMS) REW (AMS) Y·REPEAT** Plug in firmly.
i HOLD
VOL HOLD
FF REW
Y·x** VOL* x MENU SET
* There is a tactile dot beside VOL on the main unit to show the direction to turn up the volume. ** The button has a tactile dot.
5
WM-FX888 SECTION 3 DISASSEMBLY
· This set can be disassembled in the order shown below.
3-1.
DISASSEMBLY FLOW
set
3-2. CASE SECTION (page 6)
3-6. CASSETTE LID SUB ASSY (page 8)
3-3. MAIN BOARD (page 7)
3-7. REEL ORNAMENT BLOCK ASSY (page 9)
3-4. BELT (F2) (page 7)
3-8. HOLDER (F) ASSY (/M) (page 9)
3-5. MOTOR (CAPSTAN/REEL) (page 8)
3-9. PINCH LEVER (RA)/(NA) ASSY (page 10)
3-10. MAGNETIC HEAD (PLAYBACK) (HP901) (page 10)
Note: Follow the disassembly procedure in the numerical order given.
3-2.
CASE SECTION
cassette lid assy
S2 Note: On installation cassette lid assy adjust the S2 and lever (hold).
4 Close terminal board assy.
lever (hold)
5 two screws (M1.4)
6 screw (M1.4)
5 two screws (M1.4)
2 claw
1 open battery lid. 7 case section 3 battery lid
6
WM-FX888
3-3.
MAIN BOARD
1 Remove four solders of motor (M601). 2 screw (1.7 × 3) 2 screw (M1.4) (toothed lock)
S2
3 MAIN board 1 Remove six solders of head flexible board.
2 screw (1.7 × 3)
1 Remove two solders of plunger solenoid (PM901). 1 Remove four solders of leaf switch (S901).
slider
Note: On installation MAIN board adjust the S2 and slider.
3-4.
BELT (F2)
motor pulley reverse pulley
2 battery terminal board
3 belt (F2)
insert flywheel (R)
belt (F2)
insert flywheel (N)
1 Remove solder of battery terminal board.
7
WM-FX888
3-5.
MOTOR (CAPSTAN/REEL) (M601)
1 two screws (M1.4) 2 motor (capstan/reel) (M601)
3-6.
CASSETTE LID SUB ASSY
2 two screws (M1.4) 4 cassette lid sub assy
3 boss 2 screw (M1.4)
1 Open knob (open).
8
WM-FX888
3-7.
REEL ORNAMENT BLOCK ASSY
2 claw
1
4 two claws 1
5 reel ornament block assy 3 boss
3-8.
HOLDER (F) ASSY (/M)
4 screws (M1.4)
5 lock lever (S) (/M) 7 bracket (cassette) assy (/M)
8 Remove six solders of head flexible board. 2 boss 9 holder (F) assy (/M)
6 boss 3 lock lever (B) (/M)
1 two screws (IB lock)
9
WM-FX888
3-9.
PINCH LEVER (RA)/(NA) ASSY
1 claw 2 Remove pinch lever (RA) assy in the direction of the arrow.
3 claw
holder (F) assy/M
4 Remove pinch lever (NA) assy in the direction of the arrow.
3-10. MAGNETIC HEAD (PLAYBACK) (HP901)
1 claw 4 magnetic head (playback) (HP901)
3 claw
2
10
WM-FX888 SECTION 4 MECHANICAL ADJUSTMENTS
PRECAUTION 1. Clean the following parts with a denatured-alcohol-moistened swab: playback head pinch roller rubber belts capstan 2. Demagnetize the playback head with a head demagnetizer. (Do not bring the head demagnetizer close to the erase head.) 3. Do not use a magnetized screwdriver for the adjustments. 4. The adjustments should be performed with the rated power supply voltage (1.3 V) unless otherwise noted. Torque Measurement
Mode FWD CQ-102C FWD Back Tension REV CQ-102RC REV Back Tension FF, REW CQ-201B Torque Meter Meter Reading (1.47 2.94 mN·m) 15 25 g·cm (0.22 0.36 oz·inch) (0.029 0.196 mN·m) 0.3 2.0 g·cm (0.004 0.01 oz·inch) (1.47 2.94 mN·m) 15 25 g·cm (0.22 0.36 oz·inch) (0.029 0.196 mN·m) 0.3 2.0 g·cm (0.004 0.01 oz·inch) (more than 3.43 mN·m) more than 35 g·cm (more than 0.5 oz·inch) Type WS-48A Signal 3 kHz, 0 dB Used for Tape Speed Adjustment
SECTION 5 ELECTRICAL ADJUSTMENTS
PRECAUTION 1. Specified voltage : 1.3 V (DC) 2. Setting SOUND RV/MB/GRV : OFF AVLS : OFF ;NR : OFF BL SKIP : OFF
TAPE DECK SECTION
Test tape
0 dB=0.775 V
Tape Speed Adjustment Setting: Function: TAPE
Test tape WS-48A (3 kHz, 0 dB) frequency counter 16
set
+
i jack (J701)
Procedure: 1. Playback WS-48A (tape center) in the FWD state. 2. Adjsut RV601 so that the frequency counter reading becomes 3,000 Hz. Specification Values: 2,970 to 3,030 Hz 3. Playback WS-48A (tape center) in the REV state. Check that the frequency counter reading is within 2% (approx.60 Hz) of the reading of step 1. Adjustment Location: MAIN BOARD (See page 12)
11
WM-FX888
TUNER SECTION
[AM] Setting: function : RADIO BAND button : AM
AM RF signal generator
0 dB=1 µV
T2
AM IF ADJUSTMENT Adjust for a maximum reading on level meter 450 kHz AM VT VOLTAGE ADJUSTMENT Adjustment Part Frequency Display Reading on Digital Voltmeter T1
level meter
Put the lead-wire antenna close to the set. 16 set
531 kHz 1602 kHz
1.5 ± 0.1 V 8.5 ± 1 V
Confirmation
+
FM VT VOLTAGE ADJUSTMENT Adjustment Part Frequency Display Reading on Digital Voltmeter L2 Confirmation 87.5 MHz 108 MHz 3.4 ± 0.1 V Less than 10 V
30% amplitude i jack (J701) modulation by 400 Hz signal Output level: as low as possible
[FM] Setting: function : RADIO BAND button : FM
FM RF signal generator 0.01 µF set 22.5 kHz frequency deviation by 400 Hz signal Output level: as low as possible i jack (J701)
FM VCO Adjustment Setting:
FM RF SSG 0.001 µF
TP1 (FM IN) 16
level meter +
Carrier frequency : 98 MHz Modulation : no modulation Output level : 0.1 V (100 dB)
TP1 (FM IN)
digital voltmeter
Procedure: 1. Connect the frequency counter to pin qs of IC2 as shown the figure below. 2. Tune the set to 98 MHz. 3. Adjust RV1 for 19 kHz reading on the frequency counter. Specification: 18.95 kHz to 19.05 kHz
frequency counter 1 µF IC2 pin qs 33 k
+
TP2 (VT)
+
· Repeat the procedures in AM IF adjustment and AM tracking adjustment for a maximum reading on level meter.
+
Adjustment Location:
MAIN Board (Side B)
L2 FM VT Voltage Adjustment TP1 (FM IN) TP2 (VT) IC2 T2 AM IF Adjustment T1 AM VT Voltage Adjustment RV1 FM VT Adjustment RV601 Tape Speed Adjustment
1 12
12
WM-FX888 SECTION 6 DIAGRAMS
6-1. BLOCK DIAGRAM TUNER Section
X1 10.7MHz FM/AM IF AMP, FM/AM DET, MPX IC2 (1/2)
A
(Page 14)
ANT
B.P.F.
1
RF IN
RF AMP
MIX AMP
MIX OUT
6
FM IF AMP Q7, 14
CF1 10.7MHz 3
FM IF-IN
QUAD
FM RF AMP, MIX AMP, OSC IC1
7
FM IF AMP
FM DET
AF AMP
DET OUT
22
20
MPX IN
FM AM PRE AMP
L-OUT 14 DECODER R-OUT AMP 15
TUNER L-CH BUFFER Q18 R-CH
B
(Page 14)
OSC
RF OUT
6
PILOT
LOCAL/DX SWITCHING Q3
OSC
AM IF-IN
21 AM IF AMP AM DET
PILOT IN SWITCH MUTING Q19 PD1 1/2 COUNTER 1/2 COUNTER VCO
8
5
L2 FM OSC
L2 FM VT VOLTAGE PD2
DDC2 CTL
C
(Page 14)
LP2A
LP2B
LPF1
L5 AM FERRITE-ROD ANTENNA AM RF AMP Q10 24
T2 AM IF
AM RF-IN
MIX AMP OSC
MIX 4 CF2 450kHz
11
IF-OUT
IF-REQ
AM MIX AMP, OSC IC2 (2/2)
18
19
16
10 RV1 FM VCO
FM B+ Q11 SWITCHING
D3 (1/2)
OSC
T1 AM VT VOLTAGE Q13 T1 AM OSC RF B+ MUTE
2
VCO
17
D1
D2
AGC
STOP PULSE
D
(Page 14)
FM VCO BUFFER Q1, 4
D3 (2/2)
LOW-PASS FILTER Q5, 6
65
70
71
66
LOCAL/DX
FM-IN
AM-IN
DO
IF-IN 64 MONO/ST 68 STEREO/MONO SWITCHING Q12
SYSTEM CONTROLLER IC3 (1/2)
IF BUFFER Q2
· R-ch is omitted due to same as L-ch. · SIGNAL PATH : FM : AM
13
13
WM-FX888
6-2.
BLOCK DIAGRAM MAIN Section
B
TUNER L-CH
B+ SWITCH Q304
2.5V B+ ANT
A
(Page 13)
(Page 13) HP901 (PLAYBACK) L-CH FWD R-CH R-CH 1 5 AUDIO MASTER AMP (FWD/REV SELECT, PLAYBACK EQ AMP) IC301 (1/3) FWDIN-L PREAMP REVIN-L MTLDRV-L METAL 8 CONTROL PREOUT-L DOLBY NR AMP IC302 14 VCC 7 4 IN-L OUT-L 5 SW 13 R-CH AVLS CONTROL SWITCH Q305 32 PWIN-C BSTOUT BASS BOOST AMP V/I PW NF-L R-CH EQ-L 29 30
PRE-SW PW-SW MT-SW
RV301 VOL
AUDIO MASTER AMP (BASS BOOST AMP, AMS, POWER AMP) IC301 (2/3) PW IN-L POWER AMP
J701 i
+
· R-ch is omitted due to same as L-ch. · SIGNAL PATH : PLAYBACK : TUNER (FM/AM)
28
+
R-CH POWER AMP
PW-OUT-L
20
EQ
+
POWER AMP BEEP
PW-OUT-R PW-OUT-C
22 21
R-CH
F/R SW
L-CH REV R-CH R-CH
M/N SW
33
BATT B+
VCC DATA REMO GND
44
46
+
S901-2 (ATS) R-CH
12
AMSIN
AMS
AMS-OUT BST-SW
AGC DET
AGC -IN
40 FWD STOP REV S901-1 (TAPE DETECT) S1 (DIRECTION) MEGA BASS/ GROOVE SWITCHING Q302
43
35
BEEP
39
45 42 41
MUTE R-CH REVIVE/GROOVE SWITCHING Q303 1.6V B+
D
(Page 13)
COMPARATOR IC5
44
F/R-SW
29
F/R-CTL (PLAY)
52
TAPE
59
DOLBY-CTL
54
AVLS-CTL
23
DOLBY VCC-CTL
57
MB/GRV-CTL
37
AMS-IN
55
BST-CTL
56
RV-CTL
49
BEEP
27 58 28
PRE-CTL AMP-CTL MUTE-CTL
31 34
R-DATA-OUT R-DATA-IN
67
WAKE-UP
S3 10
S2 HOLD OFF HOLD
OSC-CTL MOTOR-DIR
MOTOR-CTL
DDC2 CTL DDC1-CTL RADIO-CTL BAND FM/AM
SYSTEM CONTROLLER, LIQUID CRYSTAL DISPLAY DRIVER IC3 (2/2)
S1/2-CTL
KEY-IN 43
M-CLOCK
HOLD-SENS 35 HOLD-SW 41 BATT B+ (1.5V) FM B+ (FM TUNER CIRCUIT B+) B+ SWITCH Q9 RIPPLE FILTER Q301 18 RFOUT BASE RIPPLE FILTER VCC 19
DATA I/O
XOUT
47
48 46
36 51
XIN
CS
74
75
24
50
61 40 62 30
LIQUID CRYSTAL DISPLAY LCD1
COM1 COM4
X2 75kHz 3 4
DO
2
SK
1
CS
RV601 TAPE SPEED RF B+ FM/AM TUNER CIRCUIT B+ Q601 SPEED CONTROL SWITCH COMPARATOR OUT + 11 IN+ VSP 10 9 +1.6V REGULATOR IC6 B+ SWITCH Q8
14
DI
17
EEPROM IC4
S1 S18 5 22
1.6V B+ THP601 RADIO B+ FM/AM TUNER CIRCUIT B+ 7
AUDIO MASTER AMP (RIPPLE FILTER) IC301 (3/3)
(BATTERY CASE) DC/DC CONVERTER IC801 1 D804
ROTATION DETECT SENSOR PH1 2.5V B+
SPEED CONTROL M601 (CAPSTAN/REEL) U 19 V 1 W 3
VREF Q20 SWITCH & LOGIC CIRCUIT OSC CIRCUIT BIAS START REFERENCE 8 VOLTAGE
2.5V B+
2
5
U PHOTO-IN 39 PHOTO REFLECTOR SWITCH & BUFFER Q15 W V
MOTOR DRIVE CIRCUIT
DRY BATTERY SIZE "AA" (IEC DESIGNATION R6) 1PC. 1.5V
DIRECTION CONTROL
OSC DR
CAPSTAN/REEL MOTOR DRIVE IC601 5
VT B+ PLL LOW-PASS FILTER CIRCUIT B+
DC/DC CONVERTER T801, Q801 D802 D803 POWER CONTROL Q802, 803
B+ SWITCH Q804, 805
CHARGING STAND
DC IN 4.5V
+
PHOTO-CTL 38
6
PH-CTL 60
PLUNGER DRIVE Q16, 17
PM901 (PLUNGER)
RECHARGEABLE BATTERY (NI-CD) (NC-6WM 1.2V) DDC2 CTL
C
(Page 13)
14
14
WM-FX888
6-3.
NOTE FOR PRINTED WIRING BOARD AND SCHEMATIC DIAGRAMS
Note on Schematic Diagram: · All capacitors are in µF unless otherwise noted. pF: µµF 50 WV or less are not indicated except for electrolytics and tantalums. · All resistors are in and 1/4 W or less unless otherwise specified. · C : panel designation. Note: The components identified by mark 0 or dotted line with mark 0 are critical for safety. Replace only with part number specified. · · · · · A : B+ Line. H : adjustment for repair. Total current is measured with no cassette installed. Power voltage is dc 1.5V and fed with regulated dc power supply from battery terminal. Voltages and waveforms are dc with respect to ground in no-signal (detuned) conditions. no mark : PLAYBACK ( ) : FM : AM Voltages are taken with a VOM (Input impedance 10 M). Voltage variations may be noted due to normal production tolerances. Waveforms are taken with a oscilloscope. Voltage variations may be noted due to normal production tolerances. Circled numbers refer to waveforms. Signal path. F : FM f : AM E : PLAYBACK
· Waveforms
1 IC3 uf (XOUT)
Note on Printed Wiring Board: · X : parts extracted from the component side. · Y : parts extracted from the conductor side. : Pattern from the side which enables seeing. · (The other layers' patterns are not indicated.) Caution: Pattern face side: (Side B) Parts face side: (Side A) Parts on the pattern face side seen from the pattern face are indicated. Parts on the parts face side seen from the parts face are indicated.
940 mVp-p
· This board is four-layer printed board. However, the patterns of layers 2 and 3 have not been included in the diagram.
13.3 µs
2 Q801 (Collector)
·
3.5 Vp-p
·
· ·
192 ns
3 Q801 (Base), Q803 (Emitter)
2 Vp-p
167 ns
4 Q802 (Collector), Q803 (Base)
0.3 Vp-p
184 ns
15
15
WM-FX888
6-4. PRINTED WIRING BOARD MAIN Board (Side A)
1
2
3
4
5
6
7
8
9
10
11
12
13
14
A
· Semiconductor Location
Ref. No. Location C-11 D-12 D-12 D-13 B-12 B-12 B-11 H-11 E-5 F-3 Ref. No. D803 D804 IC302 IC801 PH1 Q9 Q15 Location F-3 F-4 G-12 E-4 E-6 E-8 D-6 Ref. No. Q20 Q304 Q305 Q801 Q802 Q803 Q804 Q805 Location D-7 G-13 H-12 F-4 D-2 E-3 D-4 D-3
F1 FB2 C19 + FB1 VCC
J701 i
K
B
C
D5 D101 D201 D301 D302 D303 D304 D305 D801 D802
D302
A K FB3
D303
DATA
D304
A K
REMO FB4
A
D5
TP2 (VT) C60
A K
GND
R
C63
L
COM
MAIN BOARD (SIDE A)
FB7
Q804
R806 E C B
C813 L801 R43
D101
R34
K
D
C65
R44
E
B
R804
Q805
BCE
A
K
R807
C1 B2 E2
Q20
BCE
JC101 R73
A
D201
Q802
C C
Q15
E1 B1 C2
A
K
R805 C810 E T801
L803
C812 +
R51
JC201
D301
D801
R801 R45 R47 R309
Q803
B
5
4
A
L4
IC801
1
C807 +
RB1
K
E
R20
C805
3 C808
PH1
C
Q9
B E
R72
C
C811
A
DC/DC CONVERTER Q801
+
C40
A
C803 +
R605
R50
L802
D803
B
R803
D804
E C806 R802
K
K
C804
R71
F
A
C809 + R38
C107
C106 + C318
R308
D802
K
R74 R53
R302 R304 C303
R52
R75 R76 R56
7
C319 R301
R201 R55 C108
1
C316
R202
G
R210
C81
C210
C105 C205
R68
IC302
Q304
BCE
RV301 VOL
R102
R54 R37
R303
R110 R101 R104
C110
C80 R206
R36
8
C208 C207 C206
14
R204
S1 (DIRECTION) REV T STOP T FWD
R69 C1
R106 C2
H
TP23 (GND)
Q305 D305
CB301
R311 A
B1 E B2
I
11
1-683-354-
K
2
C317
R313
FB5
FB6
1
(11)
16
16
WM-FX888
6-5. PRINTED WIRING BOARD MAIN Board (Side B)
1
2
S901-1 (TAPE DETECT)
3
S901-2 (ATS)
4
5
6
7
8
9
10
11
12
13
14
A
MAIN BOARD
(SIDE B)
TP1 (FM IN) C7
L1 A
· Semiconductor Location
Ref. No. D1 D2 D3 D4 D6 IC1 IC2 IC3 Location B-5 C-5 H-4 C-6 D-3 B-4 E-5 E-8 Ref. No. IC4 IC5 IC6 IC301 IC601 Q1 Q2 Q3 Location D-10 E-10 E-11 H-9 F-11 E-7 D-7 B-3 Ref. No. Q4 Q5 Q6 Q7 Q8 Q10 Q11 Q12 Q13 Location C-4 E-6 D-6 C-3 D-8 D-3 F-6 F-6 F-3 Ref. No. Q14 Q16 Q17 Q18 Q19 Q301 Q302 Q303 Q601 Location C-3 D-5 D-5 H-6 H-7 G-11 H-7 G-7 D-11
R63
C8
R8
C6
D1
K C55
B
C1
C57
L7 C56
C9
Q3
BCE
1
8
R5
C18
L8 C5 4
R33 R17
R64
IC1
5
L2
DC IN 4.5V
+
CHARGING STAND DRY BATTERY SIZE "AA" (IEC DESIGNATION R6) 1PC. 1.5V
S4
R16
+
FF
Q7
C15 L3
ECB
C58 C59
C17 R15
C12
K
A
C14 C16
K
D2
R9
ECB
AMS TUNE/PRESET S5
Q14
R11
C
Q4
BCE
RECHAGEABLE BATTERY (NI-CD) (NC-6WM 1.2V) PM901 (PLUNGER)
A
CF1 S4 R62
D4
R24 C20
REW
C53
E C B R14
BCE
R23
BATTERY CASE R4 R6
R18
C22
R25
C21
ECB
Q8
60 41 R65
1
8
BCE
C27
Q16
R82
BCE
R13 C11
4 40
5 RV601 3
R603
Q10
C29 1 S5 R28 C33
C34 R29
Q2 Q6
C10 G BCE
C3
C4
61
R40
R607
D6
A
BCE
24
+
Q601
C605 C607 COM S2 HOLD HOLD t OFF
C13
R77
R12
C32
C30
Q5
S
R1
R35
C52
R10
C51
R49 1
R46
R48 5
1
IC6 2
BCE
C62
R2
E
+
D
CF2
IC2
C38
+
Q1
IC3
R70
IC5
3 4 10 1 V RB601
R601 C601
S9
C37
BCE
12 X1 S3
13
bB REPEAT
R3 R19
C2 C50 C48
C47 C46
L6
80
C45
21
R41 R42
IC601
M601 (CAPSTAN/REEL) 11 20 C608
Q11
X2
F
R31
R32
Q13
R22
LCD1 (LIQUID CRYSTAL DISPLAY) 1
C42
ECB
S3
S10
C28 T1
x RADIO OFF
ENTER
Q12
BCE
10
20
22
R602
C602
1
20
R312
L5 AM FERRITE-ROD ANTENNA
C41
C66
C306
C204 R305
S10
R21
C604 C104 C305 +
S6
R203
G
T2
S8
E
C606
C35
C49
R310
C603
B
S7 SET
R103 24 13
C308 +
C26 C64 C39 C31
C43
C36
R66
Q303
B1 E B2 R60 C1 C2 C1 R205 C2 R105
BAND ASP RADIO ON
C321
MENU
Q301
C C211 C304 + R209 R107 R208 R108
THP601
R7
IC4
K
W R207 + C201 U
C23
A
C24
A
R211 25 12 R109
R26
Q18
E1 B1 C2
R58
D3
K R27
C25
R30
RV1
R59
C1 B2 E2
Q302
C315
C320
C311 C312
+ C101
R111
C54
H
R67
R61 C44
ECB
Q19
R307
C314
C111
IC301
36 C313 37 48 1
R604
D
Q17
B1 E B2 R306 C310
11
C301 +
C309 +
1-683-354-
(11)
C307 +
HP901 (PLAYBACK)
I
+ C302 6 5 4 3 2 1 R-ch R-ch L-ch FWD (CHASSIS)
J
L-ch 1 2 3 4 5 6 (SHIELD)
REV
17
17
+
R39
WM-FX888
6-6.
SCHEMATIC DIAGRAM MAIN Board (1/2)
· See page 15 for Waveform.
· See page 20 for IC Block Diagrams.
The components identified by mark 0 or dotted line with mark 0 are critical for safety. Replace only with part number specified.
18
18
WM-FX888
6-7.
SCHEMATIC DIAGRAM MAIN Board (2/2)
· See page 15 for Waveforms.
· See page 20 for IC Block Diagrams.
The components identified by mark 0 or dotted line with mark 0 are critical for safety. Replace only with part number specified.
19
19
WM-FX888
· IC Block Diagrams IC1 TA7371AF-EL
MIX OUT RF OUT OSC VCC
IC2
TA2022AFN-EL
AM RF IN PW SW PILOT IN DET OUT MPX IN LPF 2B LPF 2A ST IND ROUT LOUT LPF1 VCO
IC302
V+
NJM2185AV-TE2
OUTA VEXT INA DETA DCA SW
14
13
12
11
10
9
8
8
7 REGULATOR
6
5
24 23 SWITCH
22
21
20
19 18
17
16
15 14
13
G2
PILOT 0° FM PRE VCO 90° ST IND AM IF
G1
V/I
RF AMP
MIX AMP
BIAS CIRCUIT
+
SUM WEIGHT + 7
DETB 20 PV 19 U 18 17 16 15 SOFT SWITCH 14 TC1 13 TC2 SPEED CONTROL CURRENT CONTROL PU GND VCC FC 12 R1 11 OUT
VLx LIMITER 5 LX BUFFER 4 VSS
OSC
AF AMP
DIVIDE DECODE
AM
1
RF IN
2
GND
3
DFC DIODE (C)
4
AFC DIODE (A)
AM DET FM DET
GM A-CH BLOCK
B-CH BLOCK: SAME AS A-CH.
STOP PULSE OSC FM IF AMP MIX AM IF AMP AGC
1
GND
2
IREF
3
VREF
4
INB
5
OUTB
6
DCB
1
VREF
2
OSC
3
FM IF IN
4
MIX OUT
5
VCC
6
AM IF IN
7
QUAD
8
AGC
9
GND
10
IF OUT
11
IF REQ
12
SP OUT
IC601
MM1279XVBE
V
1
IC301
TA2123AF (EL)
BST OUT PW NF A PW IN A PW IN B PW NF B
PW 2 3 4 MOTIVE CONTROL CIRCUIT PRE DRIVER
PW IN C LPF
BST NF
AGC IN
EQ A
EQ B
DET
W GND
36 35
34 BST +
33
32 31
30 29 28 27 26
25
AGC DET
OSC
5 6 7 8
MOTIVE/ OSC
MOTIVE LOGIC
24 RF IN 23 PW GND 22 OUT B PW B 21 OUT C
DR VREF START
C-AMP SW 37 MT TC 38 BEEP 39 AMS OUT 40 BEEP
PW C
19 VCC RIPPLE FILTER
IN+ 10
18 BASE 17 RF OUT 16 GND 15 AMS DET 14 AMS MIX
MT SW PW SW BST SW F/R SW PRE SW M/N SW
41 42 43 44 45 46
SWITCH
COMPARATOR PRE A
+
IC801
CE 1
XC6383C251ML
CHIP ENABLE VDD
PRE B MIX
+ +
13
AMS SW
PRE GND 47 VREF IN 48 VREF MTL DRV
V OUT 2
V REF + 2 STEP PFM CONTROL OSC 100/180 kHz
NC 3
1 2 3
IN A-F IN B-F VREF OUT
4
IN B-R
5
IN A-R
6
PRE NF-A
7
PRE OUT A
8
MTL DRV A
9
MTL DRV B
10 11
PRE OUT B PRE NF-B
12
AMS IN
20
20
+
+
+ +
BIAS REFERENCE VOLTAGE
PW A 20 OUT A
VSP 9
INVERTER
OUTPUT BIAS
WM-FX888
6-8. IC PIN FUNCTION DESCRIPTION
· IC3 TC9327AF-615 (SYSTEM CONTROLLER, LIQUID CRYSTAL DISPLAY DRIVER) Pin No. 1 to 4 5 to 22 23 24 25, 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 Pin Name COM1 to COM4 S1 to S18 DOLBY VCC-CTL S1/2-CTL -- PRE-CTL MUTE-CTL F/R-CTL (PLAY) BAND FM/AM R-DATA-OUT F-TUME R-TUME R-DATA-IN HOLD-SENS OSC-CTL AMS-IN PHOTO-CTL PHOTO-IN DDC1-CTL HOLD-SW BATT-DET KEY-IN F/R-SW A/D-REF (VCC) CS DATA I/O M-CLOCK BEEP MOTOR-CTL MOTOR-DIR TAPE -- AVLS-CTL BST-CTL RV-CTL MB/GRV-CTL AMP-CTL DOLBY-CTL PH-CTL I/O O O O O O O O O O O I I I I O I O I O I I I I I O I/O O O O O I O O O O O O O O Description Common drive signal output to the liquid crystal display Segment drive signal output to the liquid crystal display Power on/off control signal output of the dolby NR amplifier "L": power on (tape on), "H": power off (radio on) Capstan/reel motor speed control signal output "L": normal speed, "H": 1/2 speed Not used Pre-amplifier on/off control signal output "L": tape play, "H": radio on Power on muting control signal output "L": muting on Forward/reverse selection signal output "L": forward direction, "H": reverse direction Power on/off control signal output of the FM circuit "L": power on (FM on), "H": power off (AM or tape on) Remote control data output to the remote commander "H" is input when amplifier on mode "H" is input when amplifier on mode Communication request signal input from the remote commander Hold status detection signal input "L": hold off "H" is input when key pressing at hold mode Motor restart control signal output "L": BL skip status, "H": FF/REW motor rotation status AMS (Automatic Music Sensor) detection signal input "L": music is present, "H": music is not present Control signal output to the capstan/reel motor rotation detection circuit "L": rotation detection circuit on Rotation detection signal input of the capstan/reel motor Power on/off control signal output of the DC/DC converter circuit "H": power on HOLD switch input terminal "L": hold on Battery voltage detection signal input (A/D input) Key input terminal (A/D input) Tape direction switch input terminal (A/D input) "L": forward position Reference voltage (+1.6V) input for the A/D converter Chip select signal output to the EEPROM Two-way data bus with the EEPROM Serial clock signal output to the EEPROM Beep sound signal output Capstan/reel motor start control signal output "H": motor on Capstan/reel motor direction control signal output "L": clockwise, "H": counterclockwise Cassette tape detection switch input terminal "L": cassette detected, "H": no cassette Not used AVLS (Automatic Volume Limiter System) on/off control signal output "H": AVLS on Bass boost control signal output "H": on Emphasizing sound control signal output "L": normal, "H": RV (revive)/MB (mega bass)/GRV (groove) Emphasizing sound control signal output "L": normal/RV (revive)/GRV (groove), "H": MB (mega bass) Power on/off control signal output to the audio master amplifier "H": power on Dolby on/off control signal output "L": dolby NR on Plunger drive signal output "H": plunger on
21
WM-FX888
Pin No. 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80
Pin Name DDC2 CTL RADIO-CTL TEST IF-IN LOCAL/DX DO WAKE-UP MONO/ST GND FM-IN AM-IN VDD RESET XOUT XIN VXT VLCD C1 C2 VEE
I/O O O I I O O I O -- I I -- I O I -- -- -- -- --
Description Power on/off control signal output of the DC/DC converter circuit Power on/off control signal output of the FM and AM circuit "L": power on (FM or AM on), "H": power off (tape on) Input terminal for the test Intermediate frequency detection signal input Local/DX selection signal output of FM circuit "L": local, "H": DX PLL error signal output Input of acknowledge signal for the key entry Acknowledge signal input to accept function key in the power off status FM stereo/mono selection signal output "L": stereo, "H": mono Ground terminal FM VCO input terminal AM VCO input terminal Power supply terminal (+2.5V) System reset signal input "L": reset Main system clock output terminal (75 kHz) Main system clock input terminal (75 kHz) Connection terminal of external capacitor for oscillator circuit power supply Connection terminal of doubler circuit capacitor for liquid crystal display drive power supply Connection terminal of doubler circuit capacitor for liquid crystal display drive power supply Connection terminal of doubler circuit capacitor for liquid crystal display drive power supply Connection terminal of doubler circuit capacitor for liquid crystal display drive power supply On at input of "H" "H": power on
22
WM-FX888 SECTION 7 EXPLODED VIEWS
NOTE: · -XX and -X mean standardized parts, so they may have some difference from the original one. · Color Indication of Appearance Parts Example: KNOB, BALANCE (WHITE) . . . (RED) Parts Color Cabinet's Color · Items marked "*" are not stocked since they are seldom required for routine service. Some delay should be anticipated when ordering these items. · The mechanical parts with no reference number in the exploded views are not supplied. · Accessories are given in the last of the electrical parts list. · Abbreviation CH : Chinese model JE : Tourist model KR : Korean model
7-1. CASE SECTION
5
6
5
3
4
7 8
2 8 8
chassis section
1
Ref. No. 1 1 2 3 4 4 5 5
Part No. 3-034-068-61 3-034-068-71 3-029-219-02 3-029-220-11 3-233-968-01
Description LID, BATTERY (BLUE) LID, BATTERY (SILVER) KNOB (OPEN) SPRING, TENSION ORNAMENT (REEL) (BLUE)
Remark
Ref. No. 6 6 7 7 7 8 8
Part No. X-3381-199-1 X-3381-200-1 X-3381-692-1 X-3381-693-1 X-3381-694-1
Description
Remark
CASSETTE ASSY, LID (SILVER) CASSETTE ASSY, LID (BLUE) CASE ASSY (SILVER) (CH, KR) CASE ASSY (BLUE) (CH, KR) CASE ASSY (SILVER) (EXCEPT CH, KR)
3-233-968-11 ORNAMENT (REEL) (WHITE)...(SILVER) 3-225-996-09 SCREW (M1.4)(EG),PRECISION PAN (SILVER) 3-225-996-10 SCREW (M1.4)(EG),PRECISION PAN (BLACK)
3-225-996-11 SCREW (M1.4)(EG),PRECISION PAN (SILVER) 3-225-996-12 SCREW (M1.4)(EG),PRECISION PAN (BLACK)
23
WM-FX888
7-2. CHASSIS SECTION
55 56
54
MF-WMFX671-162
S901
57
53 53 52 58
main section
60 59 59 51
Ref. No. 51 52 53 54 54 55
Part No. 3-345-648-71 X-3377-717-2 3-389-523-02 3-029-205-02 3-029-205-22
Description SCREW (M1.4), TOOTHED LOCK BRACKET ASSY (/M) SCREW (IB LOCK) COVER, MD (JE) COVER, MD (E, KR, CH)
Remark
Ref. No. 56 57 58 59 60 S901
Part No. X-3377-719-1 3-038-054-01 3-939-590-05 3-893-942-11 3-038-056-01
Description BRACKET (CASSETTE) ASSY (/M) LEVER (B) (/M), LOCK SCREW (IB LOCK) SCREW (1.7X3), TAPPING (B) TERMINAL BOARD (MINUS) (/M)
Remark
3-365-630-41 SCREW (M1.4)
1-762-553-11 SWITCH, LEAF (TAPE DETECT, ATS)
24
WM-FX888
7-3. MAIN SECTION
104
105
103
X2
106
102
107
L5 LCD1
101
Ref. No. 101 102 103 * 104 105
Part No. 3-034-073-02 1-694-502-11 3-237-996-01 A-3021-620-A 3-029-213-01
Description HOLDER (LCD) CONDUCTIVE BOARD, CONNECTION CUSHION MAIN BOARD, COMPLETE TERMINAL BOARD, BATTERY
Remark
Ref. No. 106 107 L5 LCD1 X2
Part No. 3-031-460-01 X-3377-726-2 1-424-975-11 1-803-469-21 1-577-262-11
Description SHEET (BT) TERMINAL BOARD ASSY (/M) ANTENNA, FERRITE-ROD DISPLAY PANEL, LIQUID CRYSTAL VIBRATOR, CRYSTAL (75kHz)
Remark
25
WM-FX888
7-4. MECHANISM DECK SECTION-1 (MF-WMFX671-162)
PM901
157 160 158 156 159 163 161 155 164 158 162 163 162
154 153 152 152 151 151
mechanism deck section-2
Ref. No. 151 152 153 154 155 156 157 158
Part No. 3-010-274-02 3-010-954-01 X-3376-813-2 3-932-724-21 3-029-282-12
Description TABLE, REEL SPRING (BT), COMPRESSION CLUTCH ASSY (F) WASHER GEAR (Y)
Remark
Ref. No. 159 160 161 162 163 164 PM901
Part No. 3-029-281-01 3-040-897-04 3-029-273-01 3-007-433-12 3-029-282-12
Description GEAR, IDLER (B) SPRING (TGA), TORSION GEAR (FR) SHEET (N), REFLECTION GEAR (Y)
Remark
3-029-284-13 LEVER, TRIGGER 3-029-284-03 LEVER, TRIGGER 3-010-273-02 GEAR (REEL)
3-029-285-12 GEAR, CAM 1-454-674-32 SOLENOID, PLUNGER
26
WM-FX888
7-5. MECHANISM DECK SECTION-2 (MF-WMFX671-162)
207
210
206 209 205 211 208
M601
212
204
213
203
202 201
mechanism deck section-3
Ref. No. 201 202 203 204 205 206 207
Part No. 3-029-276-02 3-029-289-01 3-029-275-01 3-029-278-01 3-386-694-01
Description WASHER (STOPPER R) WASHER WASHER (STOPPER N) WASHER WASHER
Remark
Ref. No. 208 209 210 211 212 213 M601
Part No. 3-007-428-01 3-029-268-21 3-029-765-01 3-029-274-02 X-3377-584-5
Description WASHER (R) FLYWHEEL (R), INSERT SCREW (M1.4), TOOTHED LOCK RETAINER (F2), MOTOR CHASSIS ASSY (FA)
Remark
3-029-306-21 FLYWHEEL (N), INSERT 3-388-079-01 BELT (F2)
3-029-288-11 PULLEY, REVERSE 1-763-166-14 MOTOR (CAPSTAN/REEL) (WITH PULLEY)
27
WM-FX888
7-6. MECHANISM DECK SECTION-3 (MF-WMFX671-162)
252 253
HP901
254 255 251
Ref. No. 251 252 253
Part No.
Description
Remark
Ref. No. 254 255 HP901
Part No.
Description
Remark
X-3377-038-4 HOLDER (F) ASSY (/M) 3-033-757-01 SHEET (H) X-3377-362-1 LEVER (NA) ASSY, PINCH
3-046-789-01 SPRING (HDA) X-3377-363-1 LEVER (RA) ASSY, PINCH 1-500-576-11 HEAD, MAGNETIC (PLAYBACK)
28
WM-FX888 SECTION 8 ELECTRICAL PARTS LIST
NOTE: · Due to standardization, replacements in the parts list may be different from the parts specified in the diagrams or the components used on the set. · -XX and -X mean standardized parts, so they may have some difference from the original one. · RESISTORS All resistors are in ohms. METAL: Metal-film resistor. METAL OXIDE: Metal oxide-film resistor. F: nonflammable · Abbreviation CH : Chinese model JE : Tourist model KR : Korean model Ref. No. * Part No. Description · Items marked "*" are not stocked since they are seldom required for routine service. Some delay should be anticipated when ordering these items. · SEMICONDUCTORS In each case, u: µ, for example: uA. . : µA. . uPA. . : µPA. . uPB. . : µPB. . uPC. . : µPC. . uPD. . : µPD. . · CAPACITORS uF: µF · COILS uH: µH
MAIN
The components identified by mark 0 or dotted line with mark 0 are critical for safety. Replace only with part number specified. When indicating parts by reference number, please include the board.
Remark
Ref. No. C41 C42 C43 C44 C45 C46 C47 C48 C49 C50 C51 C52 C53 C54 C55 C56 C57 C58 C59 C60 C62 C63 C64 C65 C66 C80 C81 C101 C104 C105 C106 C107 C108 C110 C111 C201 C204 C205 C206 C207 C208 C210 C211
Part No. 1-110-563-11 1-165-176-11 1-162-969-11 1-162-969-11 1-164-360-11 1-164-360-11 1-164-360-11 1-115-156-11 1-162-917-11 1-162-917-11 1-127-895-11 1-162-910-11 1-162-915-11 1-115-156-11 1-164-676-11 1-162-910-11 1-162-910-11 1-162-970-11 1-162-970-11 1-164-676-11 1-164-227-11 1-162-919-11 1-164-217-11 1-107-826-11 1-164-245-11 1-115-156-11 1-115-156-11 1-127-895-11 1-117-863-11 1-115-156-11 1-117-863-11 1-115-467-11 1-115-156-11 1-164-677-11 1-164-227-11 1-127-895-11 1-117-863-11 1-115-156-11 1-115-156-11 1-117-863-11
Description CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP TANTALUM CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP TANTALUM CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP TANTALUM CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP 0.068uF 0.047uF 0.0068uF 0.0068uF 0.1uF 0.1uF 0.1uF 1uF 15PF 15PF 22uF 5PF 10PF 1uF 2200PF 5PF 5PF 0.01uF 0.01uF 2200PF 0.022uF 22PF 150PF 0.1uF 0.015uF 1uF 1uF 22uF 0.47uF 1uF 0.47uF 0.22uF 1uF 0.033uF 0.022uF 22uF 0.47uF 1uF 1uF 0.47uF 0.22uF 0.033uF 0.022uF 10% 10% 10% 10%
Remark 16V 16V 25V 25V 16V 16V 16V 10V 50V 50V
A-3021-620-A MAIN BOARD, COMPLETE ********************* < CAPACITOR > C1 C2 C3 C4 C5 C6 C7 C8 C9 C10 C11 C12 C13 C14 C15 C16 C17 C18 C19 C20 C21 C22 C23 C24 C25 C26 C27 C28 C29 C30 C31 C32 C33 C34 C35 C36 C37 C38 C39 C40 1-162-927-11 1-162-970-11 1-164-227-11 1-164-227-11 1-162-970-11 1-162-908-11 1-164-676-11 1-164-676-11 1-162-927-11 1-162-927-11 1-162-962-11 1-162-905-11 1-107-817-11 1-162-905-11 1-162-925-11 1-164-676-11 1-162-970-11 1-162-959-11 1-135-201-11 1-165-176-11 1-162-927-11 1-165-176-11 1-162-915-11 1-164-227-11 1-164-315-11 1-162-919-11 1-165-176-11 1-162-923-11 1-162-970-11 1-162-961-11 1-164-362-11 1-127-895-11 1-115-156-11 1-115-156-11 1-162-970-11 1-115-156-11 1-164-227-11 1-107-826-11 1-115-412-11 1-127-578-91 CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP TANTALUM CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP TANTALUM CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP TANTALUM CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP TANTALUM CHIP 100PF 0.01uF 0.022uF 0.022uF 0.01uF 3PF 2200PF 2200PF 100PF 100PF 470PF 1PF 0.33uF 1PF 68PF 2200PF 0.01uF 330PF 10uF 0.047uF 100PF 0.047uF 10PF 0.022uF 470PF 22PF 0.047uF 47PF 0.01uF 330PF 470PF 22uF 1uF 1uF 0.01uF 1uF 0.022uF 0.1uF 680PF 3.3uF 5% 10% 10% 10% 10% 0.25PF 5% 5% 5% 5% 10% 0.25PF 10% 0.25PF 5% 5% 10% 5% 20% 10% 5% 10% 0.5PF 10% 5% 5% 10% 5% 10% 10% 5% 20% 50V 25V 25V 25V 25V 50V 16V 16V 50V 50V 50V 50V 16V 50V 50V 16V 25V 50V 4V 16V 50V 16V 50V 25V 50V 50V 16V 50V 25V 50V 50V 4V 10V 10V 25V 10V 25V 16V 25V 6.3V
5% 5%
20% 4V 0.25PF 50V 0.5PF 50V 10V 5% 16V 0.25PF 0.25PF 10% 10% 5% 10% 5% 5% 10% 10% 50V 50V 25V 25V 16V 25V 50V 50V 16V 25V 10V 10V 4V 6.3V 10V 6.3V 10V 10V 16V 25V 4V 6.3V 10V 10V 6.3V 10V 16V 25V
20% 10%
10% 10% 10% 10% 20% 10%
10%
10% 10% 10% 10%
10% 10% 5% 20%
1-115-467-11 CERAMIC CHIP 1-164-677-11 CERAMIC CHIP 1-164-227-11 CERAMIC CHIP
29
WM-FX888 MAIN
Ref. No. C301 C302 C303 C304 C305 C306 C307 C308 C309 C310 C311 C312 C313 C314 C315 C316 C317 C318 C319 C320 C321 C601 C602 C603 C604 C605 C606 C607 C608 C803 C804 C805 C806 C807 C808 C809 C810 C811 C812 C813 Part No. Description 20% 20% Remark 2.5V 4V 16V 4V 4V 6.3V 2.5V 2.5V 10V 16V 16V 16V 10V 16V 10V 50V 50V 4V 16V 25V 25V 6.3V 16V 10V 16V 16V 25V 25V 25V 20V 25V 6.3V 25V 4V 10V 6.3V 25V 10V 4V 10V Ref. No. D301 D302 D303 D304 D305 D801 D802 D803 D804 Part No. Description Remark 1-119-663-11 TANTALUM CHIP 47uF 1-107-815-11 TANTALUM CHIP 2.2uF 1-164-360-11 1-127-895-11 1-127-895-11 1-117-863-11 1-125-926-95 1-125-926-95 1-135-149-21 1-164-360-11 1-165-112-11 1-165-128-11 1-115-156-11 1-165-128-11 1-115-156-11 1-162-968-11 1-162-964-11 1-135-201-11 1-164-360-11 1-164-227-11 1-164-227-11 1-125-837-11 1-107-826-11 1-115-467-11 1-164-360-11 1-107-826-11 1-162-970-11 1-162-970-11 1-162-970-11 1-135-177-21 1-164-227-11 1-125-837-11 1-164-227-11 1-127-895-11 1-115-156-11 1-117-919-11 1-162-970-11 CERAMIC CHIP TANTALUM CHIP TANTALUM CHIP CERAMIC CHIP TANTALUM CHIP TANTALUM CHIP TANTALUM CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP TANTALUM CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP TANTALUM CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP TANTALUM CHIP CERAMIC CHIP TANTALUM CHIP CERAMIC CHIP 0.1uF 22uF 22uF 0.47uF 4.7uF 4.7uF 2.2uF 0.1uF 0.33uF 0.22uF 8-719-422-37 DIODE MA8051 8-719-422-37 DIODE MA8051 8-719-422-37 8-719-422-37 8-719-422-37 8-719-049-09 8-719-420-87 DIODE DIODE DIODE DIODE DIODE MA8051 MA8051 MA8051 1SS367-T3SONY MA8130
20% 20% 10% 20% 20% 20%
8-719-404-50 DIODE MA111-TX 8-719-420-51 DIODE MA729 < FUSE >
0 F1 1uF 0.22uF 1uF 0.0047uF 10% 0.001uF 10% 10uF 0.1uF 0.022uF 0.022uF 1uF 0.1uF 0.22uF 0.1uF 0.1uF 0.01uF 0.01uF 0.01uF 1uF 0.022uF 1uF 0.022uF 22uF 1uF 10uF 0.01uF 20% 10% 10% 10% 10% 10% 10% 10% 10% 10% 20% 10% 10% 10% 20% 20% 10%
1-576-439-21 FUSE (SMD) (0.25A/125V) < FERRITE BEAD >
FB1 FB2 FB3 FB4 FB5 FB6 FB7
1-500-445-21 1-500-445-21 1-500-445-21 1-500-245-11 1-500-245-11
FERRITE FERRITE FERRITE FERRITE FERRITE
0uH 0uH 0uH 0uH 0uH 0uH 0uH
1-500-245-11 FERRITE 1-500-245-11 FERRITE < IC >
IC1 IC2 IC3 IC4 IC5 IC6 IC301 IC302 IC601 IC801
8-759-362-23 8-759-362-25 6-800-840-01 8-759-457-68 8-759-387-31 8-759-457-70 8-759-579-12 8-759-488-80 8-759-356-46 8-759-553-28
IC IC IC IC IC IC IC IC IC IC
TA7371AF-EL TA2022AFN-EL TC9327AF-615 AK93C45AV-L TC75S55F (TE85R) XC62RP1602MR TA2123AF (EL) NJM2185AV-TE2 MM1279XVBE XC6383C251ML
< JACK > J701 1-779-867-81 JACK (i) < RESISTOR > JC101 JC201 1-216-864-11 METAL CHIP 1-216-864-11 METAL CHIP < COIL > 0 0 5% 5% 1/16W 1/16W
1-115-156-11 CERAMIC CHIP 1uF 1-125-984-21 TANTALUM CHIP 22uF 1-115-156-11 CERAMIC CHIP 1uF
20%
< COMPOSITION CIRCUIT BLOCK > CB301 1-127-678-21 CAP, CHIP CERAMIC 330PF SL < CERAMIC FILTER > CF1 CF2 1-767-362-11 FILTER, CERAMIC (10.7MHz) 1-767-480-11 FILTER, CERAMIC (AM) (450kHz) < DIODE > D1 D2 D3 D4 D5 D6 D101 D201 8-719-050-97 8-719-050-97 8-719-072-58 8-719-404-50 8-719-049-09 DIODE DIODE DIODE DIODE DIODE MA357 (E)-(TX).SO MA357 (E)-(TX).SO SVC347-TL MA111-TX 1SS367-T3SONY L1 L2 L3 L4 L6 L7 L8 L801 L802 L803 1-469-373-21 1-416-941-21 1-410-997-42 1-412-995-21 1-412-995-21 1-412-967-31 1-412-967-31 1-412-034-11 1-412-995-21 1-412-010-41 INDUCTOR CHIP COIL (FM OSC) INDUCTOR CHIP INDUCTOR CHIP INDUCTOR CHIP INDUCTOR CHIP INDUCTOR CHIP INDUCTOR CHIP INDUCTOR CHIP INDUCTOR CHIP 95nH 2.2uH 22uH 22uH 0.1uH 0.1uH 330uH 22uH 22uH
< PHOTO REFLECTOR > PH1 8-749-014-43 PHOTO REFLECTOR PR-20-T
8-719-422-37 DIODE MA8051 8-719-422-37 DIODE MA8051 8-719-422-37 DIODE MA8051
30
The components identified by mark 0 or dotted line with mark 0 are critical for safety. Replace only with part number specified.
WM-FX888 MAIN
Ref. No. Part No. Description < TRANSISTOR > Q1 Q2 Q3 Q4 Q5 Q6 Q7 Q8 Q9 Q10 Q11 Q12 Q13 Q14 Q15 Q16 Q17 Q18 Q19 Q20 Q301 Q302 Q303 Q304 Q305 Q601 Q801 Q802 Q803 Q804 Q805 8-729-037-89 8-729-028-69 8-729-037-89 8-729-037-89 8-729-053-44 8-729-028-69 8-729-037-89 8-729-037-64 8-729-823-86 8-729-037-89 8-729-037-63 8-729-037-71 8-729-037-71 8-729-037-89 8-729-425-46 8-729-013-60 8-729-800-71 8-729-427-72 8-729-426-36 8-729-037-71 8-729-800-71 8-729-037-71 8-729-426-36 8-729-037-62 8-729-426-36 8-729-037-71 8-729-800-37 8-729-400-55 8-729-800-71 8-729-800-71 TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR FET TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR 2SC4627J-C (TX).SO 2SC4655-BC (TX) 2SC4627J-C (TX).SO 2SC4627J-C (TX).SO 2SK880-Y-TE85R 2SC4655-BC (TX) 2SC4627J-C (TX).SO UN9116J-(TX).SO 2SA1745 2SC4627J-C (TX).SO UN9115J-(TX).SO UN9210J-(TX).SO UN9210J-(TX).SO 2SC4627J-C (TX).SO XP4315-TXE RN1110-TE85L 2SB815B7-TB XP4501 XP1215-TXE UN9210J-(TX).SO 2SB815B7-TB UN9210J-(TX).SO XP1215-TXE UN9114J-(TX).SO XP1215-TXE UN9210J-(TX).SO 2SD1048-X7 2SD1328-S 2SB815B7-TB 2SB815B7-TB UN9210J-(TX).SO R56 R58 R59 R60 R61 R62 R63 R64 R65 R66 R67 R68 R69 R70 R71 R72 R73 R74 R75 R76 R77 R82 R101 R102 R103 1-218-875-11 1-216-833-11 1-216-833-11 1-216-833-11 1-216-833-11 1-216-845-11 1-216-853-11 1-216-853-11 1-216-849-11 1-216-839-11 1-216-839-11 1-216-825-11 1-216-825-11 1-218-895-11 1-218-851-11 1-218-871-11 1-218-831-11 1-218-855-11 1-218-839-11 1-218-875-11 1-216-829-11 1-218-959-11 1-216-823-11 1-216-837-11 1-216-789-11 METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP 15K 10K 10K 10K 10K 100K 470K 470K 220K 33K 33K 2.2K 2.2K 100K 1.5K 10K 220 2.2K 470 15K 4.7K 3.3K 1.5K 22K 2.2 0.5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 0.5% 0.5% 0.5% 0.5% 0.5% 0.5% 0.5% 5% 5% 5% 5% 5% 1/10W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/16W 1/16W 1/16W 1/16W 1/16W Remark Ref. No. R24 R25 R26 R27 R28 R29 R30 R31 R32 R33 R34 R35 R36 R37 R38 R39 R40 R41 R42 R43 R44 R45 R46 R47 R48 R49 R50 R51 R52 R53 R54 R55 Part No. Description 1K 100K 10K 470K 100K 33K 10K 68K 2.2K 2.2K 1M 2.2K 220K 1M 470K 330 10K 10K 470 220K 330K 680K 1K 1.5K 4.7K 470K 2.2K 1K 3.3K 3.3K 3.3K 4.7K 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 0.5% 0.5% 5% 5% 5% 5% 5% 0.5% 0.5% 0.5% 0.5% 0.5% 0.5% 0.5% 0.5% Remark 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/10W 1/10W 1/16W 1/16W 1/16W 1/16W 1/16W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1/10W 1-216-821-11 METAL CHIP 1-216-845-11 METAL CHIP 1-216-833-11 1-216-853-11 1-216-845-11 1-216-839-11 1-216-833-11 1-216-843-11 1-216-825-11 1-216-825-11 1-216-857-11 1-216-825-11 1-216-849-11 1-216-857-11 1-216-853-11 1-216-815-11 1-216-833-11 1-218-871-11 1-218-839-11 1-216-849-11 1-216-851-11 1-216-855-11 1-216-821-11 1-216-823-11 1-218-863-11 1-218-911-11 1-218-855-11 1-218-847-11 1-218-859-11 1-218-859-11 1-218-859-11 1-218-863-11 METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP
8-729-037-71 TRANSISTOR < RESISTOR >
R1 R2 R3 R4 R5 R6 R7 R8 R9 R10 R11 R12 R13 R14 R15 R16 R17 R18 R19 R20 R21 R22 R23
1-216-841-11 1-216-823-11 1-216-809-11 1-216-825-11 1-216-821-11 1-216-817-11 1-216-845-11 1-216-853-11 1-216-817-11 1-216-829-11 1-216-833-11 1-216-833-11 1-216-837-11 1-216-845-11 1-216-833-11 1-216-853-11 1-216-821-11 1-216-849-11 1-216-829-11 1-216-821-11
METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP
47K 1.5K 100 2.2K 1K 470 100K 470K 470 4.7K 10K 10K 22K 100K 10K 470K 1K 220K 4.7K 1K 4.7K 100K 1K
5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5%
1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W
1-216-829-11 METAL CHIP 1-216-845-11 METAL CHIP 1-216-821-11 METAL CHIP
31
WM-FX888 MAIN
Ref. No. R104 R105 R106 R107 R108 R109 R110 R111 R201 R202 R203 R204 R205 R206 R207 R208 R209 R210 R211 R301 R302 R303 R304 R305 R306 R307 R308 R309 R310 R311 R312 R313 R601 R602 R603 R604 R605 R607 R801 R802 R803 R804 R805 R806 R807 Part No. 1-216-827-11 1-216-823-11 1-216-811-11 1-216-837-11 1-216-811-11 1-218-867-11 1-216-825-11 1-216-849-11 1-216-823-11 1-216-837-11 1-216-789-11 1-216-827-11 1-216-823-11 1-216-811-11 1-216-837-11 1-216-811-11 1-218-867-11 1-216-825-11 1-216-849-11 1-216-849-11 1-216-833-11 1-216-835-11 1-216-837-11 1-216-789-11 1-216-851-11 1-216-825-11 1-218-887-11 1-216-841-11 1-216-845-11 1-216-841-11 1-216-845-11 1-218-899-11 1-216-837-11 1-216-809-11 1-216-829-11 1-216-823-11 1-216-833-11 1-216-845-11 1-216-849-11 1-216-829-11 1-216-817-11 1-216-805-11 1-216-819-11 1-216-819-11 1-216-845-11 Description METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP RES-CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP RES-CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP 3.3K 1.5K 150 22K 150 6.8K 2.2K 220K 1.5K 22K 2.2 3.3K 1.5K 150 22K 150 6.8K 2.2K 220K 220K 10K 15K 22K 2.2 330K 2.2K 47K 47K 100K 47K 100K 150K 22K 100 4.7K 1.5K 10K 100K 220K 4.7K 470 47 680 680 100K 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 0.5% 5% 5% 5% 5% 0.5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% Remark 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/10W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W Ref. No. S3 S4 S5 Part No. Description Remark 1-771-053-21 SWITCH, KEY BOARD (x, RADIO OFF) 1-771-053-21 SWITCH, KEY BOARD (AMS TUNE/PRESET, + FF) 1-771-053-21 SWITCH, KEY BOARD (AMS TUNE/PRESET, REW) 1-771-053-21 1-771-053-21 1-771-053-21 1-771-053-21 1-771-053-21 SWITCH, KEY BOARD (MENU) SWITCH, KEY BOARD (SET) SWITCH, KEY BOARD (BAND, ASP, RADIO ON) SWITCH, KEY BOARD (Y, REPEAT) SWITCH, KEY BOARD (ENTER) < COIL/TRANSFORMER > T1 T2 T801 1-416-943-21 COIL (AM OSC) 1-416-942-21 COIL (AM MIX) 1-423-745-11 TRANSFORMER, DC/DC CONVERTER < THERMISTOR (POSITIVE) > THP601 1-810-794-11 THERMISTOR, POSITIVE < CERAMIC FILTER/VIBRATOR > X1 1-767-357-11 FILTER, CERAMIC (10.7MHz) ************************************************************** MISCELLANEOUS ************** 102 HP901 L5 LCD1 M601 1-694-502-11 1-500-576-11 1-424-975-11 1-803-469-21 1-763-166-14 CONDUCTIVE BOARD, CONNECTION HEAD, MAGNETIC (PLAYBACK) ANTENNA, FERRITE-ROD DISPLAY PANEL, LIQUID CRYSTAL MOTOR (CAPSTAN/REEL) (WITH PULLEY)
S6 S7 S8 S9 S10
PM901 1-454-674-32 SOLENOID, PLUNGER S901 1-762-553-11 SWITCH, LEAF (TAPE DETECT, ATS) X2 1-577-262-11 VIBRATOR, CRYSTAL (75kHz) ************************************************************ ACCESSORIES ************ ADAPTOR, AC (AC-E455) (CH) ADAPTOR, AC (AC-E455) (JE) ADAPTOR, AC (AC-E455) (KR) ADAPTOR, AC (AC-ES455) (E) BATTERY, NI-CD (NC-6WM) ADAPTOR, CONVERSION 2P (JE) STAND, CHARGER (BCA-WM2C) CASE, BATTERY (E, KR, CH) CASE, BATTERY (JE) CASE, CARRYING
0 0 0 0
1-475-622-21 1-476-716-11 1-476-739-11 1-476-845-11 1-528-543-11 1-569-007-11 1-756-232-11 1-759-213-31 1-759-700-22 3-220-749-01
0 0
< COMPOSITION CIRCUIT BLOCK > RB1 RB601 1-233-811-21 RES, NETWORK 470K (3216) 1-233-873-21 RES, NETWORK 220K (CHIP TYPE) (3216) < VARIABLE RESISTOR > RV1 RV301 RV601 1-238-091-11 RES, ADJ, CERMET 22K 1-225-684-21 RES, VAR, CARBON 30K/30K (VOL) 1-238-088-11 RES, ADJ, CERMET 2.2K < SWITCH > S1 S2 1-771-475-21 SWITCH, SLIDE (DIRECTION) 1-572-922-11 SWITCH, SLIDE (HOLD) 8-954-008-91 RECEIVER, EAR MDR-E808SP A-3052-293-A REMOTE CONTROL ASSY (JE) 3-238-360-01 MANUAL, INSTRUCTION (JAPANESE, ENGLISH, KOREAN) (JE) 3-238-360-11 MANUAL, INSTRUCTION (ENGLISH, KOREAN) (KR) 3-238-360-21 MANUAL, INSTRUCTION (ENGLISH, SIMPLIFIED CHINESE) (CH) 3-238-360-31 MANUAL, INSTRUCTION (ENGLISH, SPANISH) (E) 3-238-360-41 MANUAL, INSTRUCTION (TRADITIONAL CHINESE) (E)
32
The components identified by mark 0 or dotted line with mark 0 are critical for safety. Replace only with part number specified.
WM-FX888
MEMO
33
WM-FX888
REVISION HISTORY
Clicking the version allows you to jump to the revised page. Also, clicking the version at the upper right on the revised page allows you to jump to the next revised page. Ver. 1.0 Date 2001.11 Description of Revision New