Text preview for : 21HS50H GA-1E.pdf part of Sharp 21HS50H Service Manual
Back to : 21HS50H GA-1E.part1.rar | Home
21HS-50H
SERVICE MANUAL
SEBD21HS50H01
Issued: 24th October 2001
GA-1E CHASSIS
PAL I SYSTEM COLOUR TELEVISION
MODEL
21HS-50H
In the interests of user safety (required by safety regulations in some countries) the set should restored to its original condition and only parts identical to those specified should be used.
CONTENTS
ELECTRICAL SPECIFICATION.........................3 IMPORTANT SERVICING NOTES ...................4 CONTROLS & TERMINALS..............................5 SERVICE ADJUSTMENTS................................6 CHASSIS LAYOUT...........................................12 LED FLASHING CODE....................................13 PRINTED WIRING BOARDS...........................13 ICs ADDITIONAL INFORMATION...................18 SCHEMATIC DIAGRAM, WAVE FORMS........26 BLOCK DIAGRAM...........................................32 TROUBLESHOOTING TABLES......................34 PARTS LISTING.............................................37
SHARP CORPORATION This document has been published to
1
be used for after sales service only.
21HS-50H
SERVICE MANUAL UPDATE LOG SHEET
Technical Report No. Technical Bulletin No. Cause / Solution Part No. Page No. Application Data /Serial No.
Use this page to keep any special servicing information as Technical Report (Bulletin), Technical Information, etc. If only part number changes are required, just change part number directly the part number in the Parts Listing Section. If you need more information, please refer to the Technical Report (Bulletin).
2
21HS-50H
ELECTRICAL SPECIFICATIONS
·Power Input .......................220V-240 Volts AC 50Hz ·Power Consumption Normal Operation....................................43W Stand-by Operation...................................3W ·Adjacent Sound Carrier Trap.................40.9MHz ·Sound Carrier Trap...............................32.9MHz
·Audio Power Output Rating ................4W x 2(MPO) Speaker................................16 4W, 9 x 5 cm,2pcs Convergence.........................Self Converging System Focus....................................Bi-Potencial Electrostatic Sweep Deflection...........................................Magnetic ·Picture Intermediate Frecuency..............38.9MHz
·Adjacent Picture Carrier Trap...............30.9MHz
·Aerial Input Impedance VHF/UHF..........................75 ohm Unbalanced ·Tuning Ranges ............45.75MHz thru 855.25 MHz VHF.............IR A - J S1-S41 (HYPERBAND) UHF.............I21 - I69 CH
·White Level Set the brightness control, with no signal connected, so that the CRT cathode current is 600mA. The maximum correction applied to each cathode current to achieve a screen temperature of 8900 degrees K-20 MPCD should not exceed 15% of its original value.
X 0.290 ± 0.015
Y 0.284 ± 0.015
Screen temperature 8900º K-20 MPCD
Specifications are subject to change without prior notice.
WARNING The chassis in this receiver is partially hot. Use an isolation transformer between the line cord plug and power receptacle, when servicing this chassis. To prevent electric shock, do not remove cover. No user-serviceable parts inside. Refer servicing to qualified service personnel.
3
21HS-50H
IMPORTANT SERVICING NOTES
Only qualified service personnel are allowed to carry out maintenance and repair of this receiver.
SERVICING OF HIGH VOLTAGE SYSTEM AND CRT
It is important that the static charge is removed from the high voltage system when carrying out work on the receiver. This can be achieved by connecting a 10K resistor (with a suitably insulated lead) from the CRT cavity connector to the CRT ground tag. This must be carried out with the AC supply disconnected from the receiver. Note the following: · The CRT in this receiver employs Integral Implosion Protection. · If the CRT has to be changed it MUST be replaced with the correct type for continued safe working · DO NOT lift the CRT by its neck. · When handing the CRT, ensure that shatterproof goggles are worn. · Ensure that the CRT is discharge before handling.
X-RAY
This receiver is designed to keep any x-ray emission to an absolute minimum. Some fault conditions and servicing procedures may produce potentially hazardous x-ray radiation levels. This is a problem when in close proximity to the receiver for long periods of time. To reduce any risks associated with this, please observe the following precautions: 1. When undertaking any servicing on this chassis, DO NOT increase the EHT to more than 30.5 KV, (at a instantaneous beam current of 1300µ). 2. Ensure that during normal operation the EHT does not exceed 25.0 KV±1.5KV (at a beam current of 1100µ). This level has been preset in the factory. Always check that this level has not been exceeded after carrying out any repair on the receiver. 3. DO NOT replace the CRT with any other type than that specified in the parts listing as this may cause excessive x-ray radiation.
BEFORE RETURNING THE RECEIVER TO THE CUSTOMER
In addition to the above checks, the following should also be carried out before returning the receiver to the customer. 1. Inspect all the leads to ensure that they are dressed correctly and that they are not obstructed or pinched by any other parts. 2. Ensure that all protective devices are in good condition. These will include nonmetallic control knobs, insulating fish papers, cabinets backs, compartment covers or shields, mechanical insulators, etc.
4
21HS-50H
Location of Controls
Remote Control
CALL ( )/CHILD LOCK ( ) button Infrared Transmitter Window Aim this window at the infrared sensor on your TV set TV/VIDEO Select button
TV
VCR
TV/VIDEO
POWER/STANDBY (
) button
Single/Double Entry button (
)
1
Programme Select buttons
2 5 8 0
3 6 9
COLOUR buttons CHANNEL (PROGRAMME) UP ( )/ DOWN ( ) buttons ( ) Selects next higher programme ( ) Selects next lower programme (These are also used for menu set up) TV button (Teletext) REVEAL (
TV
4 7
FLASHBACK ( ) button Returns to previously viewed programme VOLUME UP ( )/DOWN ( ) buttons ( ) Increases sound ( ) Decreases sound (These are also used for menu set up) MENU button
LIST
CH CH
MENU
) button (Teletext) ) button (Teletext) ) button
CLOCK (
Sound Mode Select ( HOLD (
) button (Teletext) ) button
LIST Select button (Teletext) 26 CANCEL ( STORE ( HALF PAGE ( RESET ( ) button (Teletext)
VCR
SOUND MUTE (
Text/Mix ( ) Select button (Teletext)
CH
) button (Teletext) ) button (Teletext) ) button (Teletext)
INDEX (
) button (Teletext)
GA006SA
TV/ VCR/ TEXT REMOTE CONTROL
TV Front
MENU CH
Power (
) button Channel Up ( Volume Up ( Menu button )/Down ( ) buttons
Power/On Timer indicator Remote Control Sensor
)/Down (
) buttons
Euro-SCART 21-Pin Terminal
21-Pin EuroFor greater A/V enjoyment, various audio and video devices may be connected via the Euro-SCART 21-Pin Terminal.
1. 2. 3. 4. 5. 6. 7.
Audio right output Audio right input Audio left output Common earth for audio Earth for blue Audio left input Blue input
8. Audio-video control 9. Earth for green 10. Not used 11. Green input 12. Not used 13. Earth for red 14. Not used
15. Red input 16. Red/Green/Blue control 17. Earth for video
18. 19. 20. 21.
Earth for video VIDEO output VIDEO input Common earth
Audio: Stereo Input / Output.
5
21HS-50H
SERVICE ADJUSTMENT
· SERVICE MODE FUNCTION ·
All required adjustments for servicing this TV set, may be done in "service mode", excepting G2 and FOCUS.
HOW TO ACCESS THE SERVICE MODE 1. 2. 3. 4. Turn the receiver on and ensure that it is tuned into a test pattern. Turn the receiver off using the mains switch. Press the volume down and channel up buttons together. See Fig.1. Continue pressing the volume down and channel up buttons while turning the mains on using the mains switch. See Fig.1. Keep pressing the volume down and channel up buttons until the picture appears. When <> appears on the screen, release the two buttons. The receiver is now in the service mode. See Fig. 2.
4
Fig.1
MENU
CH
3
5. 6. 7.
To move between the various service mode functions, use the channel up and down buttons. See Fig. 3. Use the volume buttons to change the data to the desired value. See Fig. 3. The data will be stored automatically when exiting the service mode. To exit the service mode press the standby button on the remote control or turn the receiver off with the mains switch.
·
· ·
Fig. 2
Fig. 3
SHARP X
X VXX.XX Adjustment (Yellow) XXXX: XX: Value (Green)
STS0: XXXX XXXX STS1: XXXX XXXX STS2: XXXX XXXX
6
21HS-50H
· SERVICE ADJUSTMENTS AND DATA LIST
The table below shows the various service mode positions, range of values and default value. The columns are headed as follows.
Heading: OSD Function Range Initial Default FIX/ADJ
Description: This is what will appear on the screen when at this position This is the description of the mode's function This is the range of values that can be entered while in this mode This is the initial value, i.e. just after changing the NVM This is the recommended default value for this mode If this is ADJ, then it may be necessary to adjust this value away from the default
No. OSD
Function
Range
Initial
Default
FIX/ADJ
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24
AGC V-LIN V-AMP V-CENT H-CENT H-CENT60 EW / / HB S-COR DRI-RS DRI-GS DRI-BS DRI-RW DRI-GW DRI-BW DRI-RC DRI-GC DRI-BC SUB-VOL SUB-CON SUB-COL SUB-BRI TINT SUB-SHP
AGC Take Over Point Vertical Slope [VS] Vertical Amplitude [VA] Vertical Shift [VSH] Horizontal shift [HS] offset to H-CENT for60 Hz Horizontal Parallelogram [HP] Horizontal Bow S-Correction [SC] White point Red Standard white temp.
0...63 0...63 0...63 0...63 0...63 0...31 data(-16..+15) 0...63 0...63 0...63 0...63
14 32 32 32 32 16 32 32 0 32 32 32 16 16 16 16 16 16 60 63 32 32 32 32
14 32 32 32 32 20 32 32 22 42 42 42 16 9 9 9 9 16 60 63 25 34 32 11
ADJ ADJ ADJ ADJ ADJ FIX FIX FIX FIX ADJ ADJ ADJ FIX FIX FIX FIX FIX FIX FIX FIX FIX FIX FIX FIX
White point Green Standard white temp. 0...63 White point Blue Standard white temp White point Red Warm white temp. White point Green Warm white temp. White point Blue Warm white temp. White point Red Cold white temp. White point Green Cold white temp. White point Blue Cold white temp. Max Volume Sub Contrast Sub Colour Sub Brightness Sub Tint Sub Sharpness 0...63 0...32 0...32 0...32 0...32 0...32 0...32 0...63 0...63 0...63 0...63 0...63 0...63
7
21HS-50H
No. OSD 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 HTL-VOL HTL-PRG RGB SEARCH-SYS CUT-R CUT-G CDL DL-PT DL-ST DL-4T COL-OP COL-OS COL-O4 SHP-OP SHP-OS SHP-O4 SC-VOL PRE-SC PRE-FM PRE-NICAM AVC-DKY AC-OFF-TIM
Function Max Hotel Volume Hotel Program number OSD RGB Reference Sound system for auto turning Black Level off-set R [BLR] Black Level off-set G [BLB] Cathode Drive Level [CL] Y-Delay time for PAL (TV) [YD] Y-Delay time for SECAM (TV) [YD] Y-Delay time for N443 (TV) [YD] COLOUR OFFSET (PAL) COLOUR OFFSET (SECAM) COLOUR OFFSET (NTSC443) SHARPNESS OFFSET(PAL) SHARPNESS OFFSET(SECAM) SHARPNESS OFFSET(NTSC443) SCART volume Prescaler SCART input Prescaler FM/AM Prescaler SCART input AVC Decay Time to set the AC-OFF timer is in steps of 10minutes Language or symbols
Range 0...63 0...99 or > 99 for none 0...15 0(L-BG),1(BG),2(I),3(DK) 0...63 0...63 0...15 0...15 0...15 0...15 0...15 0...15 0...15 0...15 0...15 0...15 0..255 0..127 0..127 0..127 0...3 data(1.2.4.8.) 0..15 0(symboles), 1(English), 2(French) 0 (teletext pan-european language) 1 (second language;cyrillic) 2(third language;Greek) 0 (disable) or 1 (enable) 0 (disable) or 1 (enable) 0 (disable) or 1 (enable) 0 (disable) or 1 (enable) 0 (disable) or 1 (enable) 0 (disable) or 1 (enable) 0 (disable) or 1 (enable) 0 (disable) or 1 (enable) 0 (disable) or 1 (enable) 0 (disable) or 1 (enable) 0 (disable) or 1 (enable) 0 (disable) or 1 (enable) 0 for 1 AV or 1 for 2 AV 0 (disable) or 1 (enable) 0 (disable) or 1 (enable) 0 (disable) or 1 (enable) 0 (disable) or 1 (enable) 0 (disable) or 1 (enable) 0 (disable) or 1 (enable) 0 (disable) or 1 (enable) 0 (disable) or 1 (enable) 0 (disable) or 1 (enable) 0 (disable) or 1 (enable) 0 (westem) or 1 (eastem) 0 (disable) or 1 (enable) 0 for Ph1 or 1 for Ph2 0 (fast tuning) or 1 (moderate speed tuning) 0 (disable) or 1 (enable) 0 (disable) or 1 (enable) 0 (disable) or 1 (enable) 0 or 1 0 (disable) or 1 (enable)
Initial 30 255 15 1 0 0 0 12 15 12 8 8 4 8 4 8 115 25 72 0 2 0 0
Default 30 255 0 2 0 10 5 4 8 8 8 8 4 8 4 8 109 25 72 90 1 0 1
FIX/ADJ FIX FIX FIX FIX FIX FIX FIX FIX FIX FIX FIX FIX FIX FIX FIX FIX FIX FIX FIX FIX FIX FIX FIX
47 DISP
48
TXT-EUR
Teletext pan-European language
0
0
FIX
49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75
BKS AVC FFI ACL S-L S-DK S-I S-BG BLUE-BACK VMC HTL BTSC AV FMWS SM0 SM1 AGC0 AGC1 FOA-FE FOB-FE FOA-AV FOB-AV TXT TXT-WE FSL HP2 CP
Black Stretch Automatic Volume Control(AVL) Fast Filter IF-PLL Auto Colour Limit Sound system L Sound system DK Sound system I Sound system BG Video mute at Ident loss Video Mute at program/source Change Hotel mode Reduced FM demodulator Gain (for BTSC sig) Number of external AV sources FM Window Selection Sound Mute bit 0 Sound Mute bit 1 IF AGC speed bit0 IF AGC speed bit1 Phi 1 time constant for FE(RF) Phi 2 time constant for FE(RF) Phi 1 time constant for AV Phi 2 time constant for AV Teletext Teletext Western or Eastern characters Forced V-SYNC slicing level Sync of OSD Charge pump NICAM decoding enabled IGR decoding enabled Start auto tuning at POWER-ON Function of TXT key Enable Vertical Guard
1 0 0 0 0 1 1 1 1 1 0 0 1 0 1 0 1 0 0 0 1 1 0 0 0 0 0 0 0 0 0 1
1 1 0 1 0 0 1 0 1 1 0 0 0 0 1 0 1 0 0 0 1 1 1 0 0 0 0 1 0 0 0 1
FIX FIX FIX FIX FIX FIX FIX FIX FIX FIX FIX FIX FIX FIX FIX FIX FIX FIX FIX FIX FIX FIX FIX FIX FIX FIX FIX FIX FIX FIX FIX FIX
76 NICAM 77 IGR 78 AUTO 79 TXT-TGL 80 EVG
8
21HS-50H
· SCREEN ADJUSTMENT 1. G2 Adjustment
1. 2. 3. 4. 5. 6. 7. 8. 9. Enter the service mode (see page 6). Use the channel up or channel down buttons to enter the << BLUE-BACK >> function. Set this to << BLUE-BACK: 0 >>, i.e. blue background is turned off. Turn the set off at the mains. Turn the set back on. Set the picture control settings to normal. Select the SCART input by pressing the TV/SCART button on the remote control. Do not connect an input to the SCART socket. A blank raster will appear. Connect an oscilloscope to TP851 on the CRT PWB. The waveform as in figure 4 should be displayed. Adjust the G2 control (screen voltage) so that the peak of this waveform is 3.0V +/-0.1V above the zero volt line.
9GF
9
9
Fig. 4
10. Enter the service mode. 11. Turn the blue background function back on again - set << BLUUE-BACK: 1 >>. 12. Turn off the receiver using the mains button. 13. The G2 adjustment is now complete.
2. Focus Adjustment
1. 2. 3. Receive a monoscope pattern signal at a level of 60 to 80 dBuV. Set the picture settings to normal. Adjust the focus potentiometer to obtain maximum definition.
· AGC ADJUSTMENT
1. 2. 3. 4. 5. 6. 7. 8. Tune the receiver into a colour bar signal on channel E-12. Set the RF generator to an output signal strength of 57dBuV (+/-1dBuV) 50 Ohms unbalanced. Connect an oscilloscope to TP201. TP201 is one end of R201. Enter the service mode (see page 6). Use the channel up and channel down buttons to enter the AGC mode. By using the volume up and the volume down buttons, adjust the AGC until the voltage on TP201 drops by 0.1V to 0.3V below its maximum value. Change the input signal strength to 66-70dBuV and make sure that there is no noise apparent in the picture. Turn the receiver off at the mains, this will exit the service mode and store the adjustment.
9
21HS-50H
· GEOMETRY ADJUSTMENT PROCEDURE
To adjust the geometry, follow the procedure outlined below: 1.Tune the set into a Philips test pattern. 2.Enter the service mode as described on page 6. 3.Use the channel up or channel down buttons to enter the desired mode 4.Use the volume buttons to achieve correct setting. 5.When adjustments are complete, use the standby button to turn off the set. The adjustment values will be stored at this point.
V-LIN Adjust the vertical linearity control so that the picture centring is as shown in figure 5.
Fig. 5 V-AMP Adjust the vertical amplitude control so that the picture overscans as shown in figure 6.
Fig. 6 V-CENT Adjust the vertical centring control so that the picture is centred as shown in figure 7.
Fig. 7 H-CENT Adjust the horizontal centring control so that the picture is centred as shown in figure 8.
Fig. 8
10
21HS-50H
·COLOUR ADJUSTMENT PROCEDURE
The following adjustments should only be carried out when the CRT or IC801 are replaced.
NOTES: · This adjustment must be done after warming up the unit for 30 minutes or longer with a beam current over 700 µA. · The red value «DRI-RS» should be fixed to 42. (Refer to "How to access service mode" section). · «DRI-GS» adjustment alters "Y" co-ordinate. · «DRI-BS» adjustment alters "X" and "Y" co-ordinates.
ADJUSTMENT METHOD 1 (using the signal generator, varying the picture signal) 1. 2. 3. 4. 5. Adjust G2. Input a white pattern with burst signal from SCART. Position the colorimeter in the centre of screen. Adjusting input signal level, select a luminance of 70 nits. Operate again in "service mode" and select «DRI-GS» and/or «DRI-BS» locations to obtain colour co-ordinates:
X 0.290 ± 0.015
Y 0.284 ± 0.015
Screen temperature 8900º K-20 MPCD
6. Re-set the TV with the mains switch button to store the adjustment and exit service mode. 7. Check colour co-ordinates "X" and "Y" at 20 a 120 Nits. It may be necessary to repeat the same procedure to obtain the above values.
ADJUSTMENT METHOD 2 (using the signal generator, with a fixed picture signal) 1. 2. 3. 4. 5. Adjust G2. Tune a white pattern with burst signal. Operate in "service mode": Using «SUB-CON», select a luminance of 70 nits. Operate again in "service mode" and select «DRI-GS» and/or «DRI-BS» locations to obtain colour co-ordinates:
X 0.290 ± 0.015
Y 0.284 ± 0.015
Screen temperature 8900º K-20 MPCD
6. Select «SUB-CON». Return data to "63". 7. Re-set the TV with the mains switch button to store the adjustment and exit service mode. 8. Check colour co-ordinates "X" and "Y" at 20 a 120 Nits. It may be necessary to repeat the same procedure to obtain the above values.
11
21HS-50H
CHASSIS LAYOUT MOTHER UNIT
CRT UNIT
12
21HS-50H
LED FLASHING CODE
PURPOSE: INPUT: The led indicates the power mode,ocurred I2C error and On timer - Current power mode - I2C Errors - On timer
Processing:
- If in STANDBY mode and On timer in-active then switch LED off. - If in STANDBY and On timer active set LED to blinking, (switch on and off at 1 Hz with a 50 % duty cycle). - If in POWER-ON mode, switch LED on. - If an I2C error occurred, let the LED blink at 1 Hz, 50 % duty cycle. For the blinking times see the Table below.
Note:
Only when an I2C error occurs for a number of times, or for a number of seconds, the I2C error is handled by the system (that is ,only then the set will go to standby, the led starts blinking).
IC/Module Name
Slave Address
Bus Error LED Remarks Blinking Time 2 3 6 6 5 512x8 EEPROM Address of internal TV processor PLL Tuner Multistandard Sound Processor
Ref. No.
M24C04 A0,A2 TDA935x/6x/8x 8A VTST6HD64 or C0 CTF551 C0 MSP34x5G 80 Table Error LED blinking times
IC1002 IC801 TU201 IC3001
F 7341N0 PRINTED WIRING BOARD. Components side.
6
5
4
3
2
1 Y 0 X 1 2 3 4 5 6 7 8 9 10
13
21HS-50H
F 7340N4 PRINTED WIRING BOARD. Components side.
25 24
23
22
21
20
19
18
17
16
15
14
13
12
11
10
9
8
7
6
5
4
3
Page 15
2
1 Y 0 X 1 2 3 4 5 6 7 8 9 10 11 12 13
14
21HS-50H
F 7340N4 PRINTED WIRING BOARD. Components side.
25 24
23
22
21
20
19
18
17
16
15
14
13
12
11
10
9
8
7
6
5
4
3
Page 14
2
1
Y 12 13 14 15 16 17 18 19 20 21 22 23 24 X 25
15
21HS-50H
F 7340N4 PRINTED WIRING BOARD. Copper side.
25 24
23
22
21
20
19
18
17
16
15
14
13
12
11
10
9
8
7
6
5
4
3
Page 17
2
1 Y 25 X 24 23 22 21 20 19 18 17 16 15 14 13 12
16
21HS-50H
F 7340N4 PRINTED WIRING BOARD. Copper side.
25 24
23
22
21
20
19
18
17
16
15
14
13
12
11
10
9
8
7
6
5
4
3
Page 16
2
1
Y 13 12 11 10 9 8 7 6 5 4 3 2 1 X 0
17
21HS-50H
ICs ADDITIONAL INFORMATION:TDA9350(IC801)
QUICK REFERENCE DATA SYMBOL Supply VP IP Input voltages ViVIFrms) ViSIF(rms) ViAUDIO(rms) ViCVBS(p-p) ViCHROMA(p-p) ViRGB(p-p) ViYIN(p-p) ViUVIN(p-p) Vo(IFVO)(p-p) Vo(QSSO)(rms) video IF amplifier sensitivity (RMS value) QSS sound IF amplifier sensitivity (RMS value) external audio input (RMS value) external CVBS/Y input (peak-to-peak value) external chroma input voltage (burst amplitude) (peak-to-peak value) RGB inputs (peak-to-peak value) luminance input signal (peak-to-peak value) U/V input signal (peak-to-peak value) - - - - - - - - - - - 0 - 10 1 1.2 75 60 500 1.0 0.3 0.7 1.4 - - - - - - - µV µV mV V V V V V supply voltages supply current - - 8.0/3.3 135/60 - - V mA PARAMETER MIN. TYP. MAX. UNIT
1.33/1.05 - 2.5 100 500 - 2.0 - - - - - - 5 - - - -
Output signals demodulated CVBS output (peak-to-peak value) sound IF intercarrier output in QSS versions (RMS value) V mV mV mA V mA mA mA
Vo(AMOUT)(rms) demodulated AM sound output in QSS versions (RMS value) Io(AGCOUT) VoRGB(p-p) IoHOUT IoVERT IoEWD tuner AGC output current range RGB output signal amplitudes (peak-to-peak value) horizontal output current vertical output current (peak-to-peak value) EW drive output current
AUDOUT/AMOUT
EHTO AUDEXT/QSSO/ AMOUT
INSSW2
IFVO/SVO
P1.2/INT0
P1.0/INT1
XTALOUT
CHROMA
OSCGND
CVBSINT
CVBS/Y
P1.1/T0
XTALIN
RESET
G2/YIN
B2/UIN
R2/VIN
BCLIN
FBISO HOUT
BLKIN
VDDC
VDDP
GND1
VDDA
PLLIF
P3.0/ADC0/PWM0
P3.1/ADC1/PWM1
P3.2/ADC2/PWM2
P3.3/ADC3/PWM3
AUDEEM/SIFIN1 DECSDEM/SIFIN2
SNDPLL/SIFAGC
18
AVL/SNDIF/ REFO/AMOUT
handbook, halfpage
P2.0/TPMW
P1.7/SDA
P1.6/SCL
DECDIG
SECPLL
VSSC/P
P1.3/T1
TUNERAGC
AVL/EWD
DECBG
PH2LF
PH1LF
GND3
VDRB VDRA
VSSA
P0.5
P0.6
VP2
GND2
IFIN1
IFIN2
IREF
VSC
Fig. 3 Pin configuration (SDIP 64)
VPE
64
63
62
61
60
59
58
57
56
55
54
53
52
51
50
49
48
47
46
45
44
43
42
41
40
39
VP1
GO
RO
BO
38
37
36
35
34
33 32
MXXxxx
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
1
2
3
4
5
6
7
8
9
TDA935X/6X/8X PS/N2
XXX
SNDIF
RESET
SOUND TRAP SCL SDA +3.3 V VPE VST OUT AUDEXT AUDOUT
BLOCK DIAGRAM
LED OUT (2x)
TUNERAGC 10/11 (20) 29 28 (32) 35 1+62-64 DEEMPHASIS ENHANCED 1/10 PAGE MEMORY 80C51 CPU VST PWM-DAC I/O PORTS AUDIO SWITCH (AVL) VOLUME CONTROL I2C-BUS TRANSCEIVER 5-8 44 60 55 59 58 57 3 4 9 2 12 54 56 61
27
37
38
(32) 31
23
IFIN
24
VISION IF ALIGNMENT-FREE PLL DEMOD. AGC/AFC VIDEO AMP.
ADC IN (4x)
I/O PORTS (4x)
40 CVBS ROM/RAM ACQUISITION V TELETEXT
VIDEO SWITCH
H TELETEXT/OSD DISPLAY
CVBS/Y
42
VIDEO IDENT.
CHROMA 43 SYNC REF BASE-BAND DELAY LINE LUMA DELAY PEAKING BLACK STRETCH COR
VIDEO FILTERS
AGC CIRCUIT NARROW BAND PLL DEMODULATOR R G
REF
B BL CONTR/BRIGHTN OSD/TEXT INSERT CCC WHITE-P. ADJ. R G B 51 52 53 49 50 RGB/YUV INSERT RO GO B0 BCLIN BLKIN
ICs ADDITIONAL INFORMATION:TDA9350(IC801)
19
H-DRIVE V-DRIVE + V GEOMETRY (EW GEOMETRY) 2nd LOOP H-SHIFT 34 16 33 25 26 22 21 36 (20) HOUT V-DRIVE EHTO EWD
13
PAL/SECAM/NTSC DECODER (32)
30
41
18 Y U V
+8V
39
H/V SYNC SEP.
RGB/YUV MATRIX SATURATION YUV/RGB MATRIX 46 47 48 45
14
H-OSC. + PLL
19
H
15
17
R/V G/Y B/U BL
21HS-50H
Block diagram TDA935X/6X8X PS/N2 with mono intercarrier sound demodulator
21HS-50H
ICs ADDITIONAL INFORMATION:TDA9350(IC801)
PINNING SYMBOL P1.3/T1 P1.6/SCL P1.7/SDA P2.0/TPWM P3.0/ADC0/PWM0 P3.1/ADC1/PWM1 P3.2/ADC2/PWM2 P3.3/ADC3/PWM3 VSSC/P P0.5 P0.6 VSSA SECPLL VP2 DECDIG PH2LF PH1LF GND3 DECBG AVL/EWD (1) VDRB VDRA IFIN1 IFIN2 IREF VSC TUNERAGC AUDEEM/SIFIN1(1) DECSDEM/SIFIN2(1) GND2 SNDPLL/SIFAGC(1) AVL/SNDIF/REF0/ AMOUT(1) HOUT FBISO AUDEXT/ QSSO/AMOUT(1) EHTO PLLIF IFVO/SVO VP1 CVBSINT GND1 CVBS/Y CHROMA AUDOUT /AMOUT(1) PIN 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 DESCRIPTION port 1.3 or Counter/Timer 1 input port 1.6 or I2C-bus clock line port 1.7 or I2C-bus data line port 2.0 or Tuning PWM output port 3.0 or ADC0 input or PWM0 output port 3.1 or ADC1 input or PWM1 output port 3.2 or ADC2 input or PWM2 output port 3.3 or ADC3 input or PWM3 output digital ground for µ-Controller core and periphery port 0.5 (8 mA current sinking capability for direct drive of LEDs) port 0.6 (8 mA current sinking capability for direct drive of LEDs) analog ground of Teletext decoder and digital ground of TV-processor SECAM PLL decoupling 2nd supply voltage TV-processor (+8V) decoupling digital supply of TV-processor phase-2 filter phase-1 filter ground 3 for TV-processor bandgap decoupling Automatic Volume Levelling /East-West drive output vertical drive B output vertical drive A output IF input 1 IF input 2 reference current input vertical sawtooth capacitor tuner AGC output audio deemphasis or SIF input 1 decoupling sound demodulator or SIF input 2 ground 2 for TV processor narrow band PLL filter /AGC sound IF Automatic Volume Levelling / sound IF input / subcarrier reference output /AM output (non controlled) horizontal output flyback input/sandcastle output external audio input /QSS intercarrier out /AM audio output (non controlled) EHT/overvoltage protection input IF-PLL loop filter IF video output / selected CVBS output main supply voltage TV-processor (+8 V) internal CVBS input ground 1 for TV-processor external CVBS/Y input chrominance input (SVHS) audio output /AM audio output (volume controlled)
20
21HS-50H
ICs ADDITIONAL INFORMATION:TDA9350(IC801)
SYMBOL INSSW2 R2/VIN G2/YIN B2/UIN BCLIN BLKIN RO GO BO VDDA VPE VDDC OSCGND XTALIN XTALOUT RESET VDDP P1.0/INT1 P1.1/T0 P1.2/INT0 Note
PIN 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 2nd
DESCRIPTION RGB / YUV insertion input 2nd R input / V (R-Y) input 2nd G input / Y input 2nd B input / U (B-Y) input beam current limiter input / (V-guard input, note 2) black current input / (V-guard input, note 2) Red output Green output Blue output analog supply of Teletext decoder and digital supply of TV-processor (3.3 V) OTP Programming Voltage digital supply to core (3.3 V) oscillator ground supply crystal oscillator input crystal oscillator output reset digital supply to periphery (+3.3 V) port 1.0 or external interrupt 1 input port 1.1 or Counter/Timer 0 input port 1.2 or external interrupt 0 input
1. The function of pin 20, 28, 29, 31, 32, 35 and 44 is dependent on the IC version (mono intercarrier FM demodulator / QSS IF amplifier and East-West output or not) and on some software control bits. The valid combinations are given in table 1. 2. The vertical guard function can be controlled via pin 49 or pin 50. The selection is made by means of the IVG bit in subaddress 2BH. Table 1 Pin functions for various versions FM-PLL version QSS version
IC version
East-West Y/N N Y N Y CMB1/CMB0 bits 00 01/10/11 00 01/10/11 00 01/10/11 00 01/10/11 AM bit - - - - - 0 1 - 0 1 Pin 20 AVL EWD AVL EWD Pin 28 AUDEEM SIFIN1 Pin 29 DECSDEM SIFIN2 Pin 31 SNDPLL SIFAGC REFO(2) AMOUT REFO(2) Pin 32 SNDIF(1) REFO(2) AVL/SNDIF(1) REFO(2) AMOUT Pin 35 AUDEXT AUDEXT QSSO AMOUT AUDEXT QSSO AMOUT Pin 44 AUDOUT controlled AM or audio out Note 1. When additional (external) selectivity is required for FM-PLL system pin 32 can be used as sound IF input. This function is selected by means of SIF bit in subaddress 28H. 2. The reference output signal is only available for the CMB1/CMB0 setting of 0/1. For the other settings this pin is a switch output (see also table 67).
21
21HS-50H
ICs ADDITIONAL INFORMATION:TEA1507(IC701)
ndbook, full pagewidth
VCC
1
SUPPLY MANAGEMENT internal UVLO start supply
START-UP CURRENT SOURCE
8
DRAIN HVS n.c.
clamp VALLEY
7
GND
2
S1
M-level
VOLTAGE CONTROLLED OSCILLATOR
4
LOGIC
100 mV
DEM
FREQUENCY CONTROL
OVERVOLTAGE PROTECTION
OVERTEMPERATURE PROTECTION
LOGIC
DRIVER
Iss
6
DRIVER
CTRL
3
-1
POWER-ON RESET
S
Q
LEB blank
soft start S2
0.5 V
2.5 V
burst detect
UVLO
R
Q
5 OCP Isense
TEA1507
MAXIMUM ON-TIME PROTECTION
short winding
0.75 V
OVERPOWER PROTECTION
MGU230
Block diagram.
PINNING SYMBOL PIN VCC GND CTRL DEM Isense DRIVER HVS DRAIN 1 2 3 4 5 6 7 8 ground control input input from auxiliary winding for demagnetization timing, OVP and OPP programmable current sense input gate driver output high voltage safety spacer, not connected drain of external MOS switch, input for start-up current and valley sensing Pin configuration. DESCRIPTION supply voltage
handbook, halfpage
VCC 1 GND 2
8 DRAIN 7 HVS
TEA1507
CTRL 3 DEM 4
MGU231
6 DRIVER 5 Isense
22
21HS-50H
ICs ADDITIONAL INFORMATION:AN7523(IC303)
Circuit Function Block Diagram
Pin Descriptions
Pin No. 1 2 3 4 5 6 7 8 9 Description Vcc Ch Output (+) GND Ch Output (-) Standby Ch Input GND (Input) N.C Volume
VCC 1
2
3
4
5
6
7
8
Standby
Note: Do not apply voltage or current to NC pin from outside
ICs ADDITIONAL INFORMATION:AN5522(IC501)
Volume
Output
Output
GND
GND
Input
N.C.
9
Circuit Function Block Diagram
Pin Descriptions
Pin No. Pin Name Inverting Input Power Supply Pump-up Output GND Vertical Output Vertical Output Power Supply Non-inverting Input
Thermal Protection
1 2 3 4 5 + 6 7
Pump Up
Amp
1
Inverting Input
2
Vcc
3
Pump Up Out
4
GND
5
Output
6
Output Vcc
7
Non-inverting Input
23
21HS-50H
ICs ADDITIONAL INFORMATION:MSP34x5G (IC3001)
Absolute Maximum Ratings Symbol TA TS VSUP1 VSUP2 VSUP3 dVSUP23 PTOT Parameter Ambient Operating Temperature Storage Temperature First Supply Voltage Second Supply Voltage Third Supply Voltage Voltage between AVSUP and DVSUP Package Power Dissipation PSDIP64 PSDIP52 PQFP80 PLQFP64 PMQFP44 Input Voltage, all Digital Inputs Input Current, all Digital Pins Input Voltage, all Analog Inputs Input Current, all Analog Inputs Output Current, all SCART Outputs Output Current, all Analog Outputs except SCART Outputs Output Current, other pins connected to capacitors SCn_IN_s,2) MONO_IN SCn_IN_s,2) MONO_IN SC1_OUT_s2) DACM_s2) CAPL_M, AGNDC Pin Name AHVSUP DVSUP AVSUP AVSUP, DVSUP AHVSUP, DVSUP, AVSUP Min. 0 Max. 70 125 9.0 6.0 6.0 0.5 Unit
°C °C
V V V V
-40 -0.3 -0.3 -0.3 -0.5
1300 1200 1000 960 960
mW mW mW mW mW V mA1) V mA1)
VIdig IIdig VIana IIana IOana IOana ICana
1) 2) 3) 4)
-0.3 -20 -0.3 -5
3) 4)
VSUP2+0.3 +20 VSUP1+0.3 +5
3) 4)
,
,
3)
3)
3)
3)
positive value means current flowing into the circuit "n" means "1" or "2", "s" means "L" or "R" The Analog Outputs are short-circuit proof with respect to First Supply Voltage and Ground. Total chip power dissipation must not exceed absolute maximum rating.
Stresses beyond those listed in the "Absolute Maximum Ratings" may cause permanent damage to the device. This is a stress rating only. Functional operation of the device at these or any other conditions beyond those indicated in the "Recommended Operating Conditions/Characteristics" of this specification is not implied. Exposure to absolute maximum ratings conditions for extended periods may affect device reliability.
24
21HS-50H
ICs ADDITIONAL INFORMATION:MSP34x5G (IC3001)
NC VREF1 SC1_OUT_R SC1_OUT_L NC AHVSUP DACM_L DACM_R VREF2 NC NC
33 32 31 30 29 28 27 26 25 24 23 CAPL_M AHVSS AGNDC SC2_IN_L SC2_IN_R ASG SC1_IN_L SC1_IN_R VREFTOP MONO_IN AVSS 34 35 36 37 38 39 40 41 42 43 44 1 AVSUP ANA_IN1+ ANA_IN- TESTEN XTAL_IN XTAL_OUT TP 2 3 4 5 6 7 8 9 10 11 STANDBYQ ADR_SEL D_CTR_I/O0 D_CTR_I/O1 22 21 20 19 18 RESETQ I2S_DA_IN2 DVSS DVSUP ADR_CL I2S_DA_IN1 I2S_DA_OUT I2S_WS I2S_CL I2C_DA I2C_CL
MSP 34x5G
17 16 15 14 13 12
PMQFP44 package
Sound IF1
ADC
Demodulator
Preprocessing
Loudspeaker Sound Processing
DAC
Loudspeaker
I2S1 I2S2 Prescale
Source Select
I2S
SCART1 DAC SCART DSP Input Select
SCART2
ADC
Prescale
SCART Output Select
SCART1
MONO
Simplified functional block diagram of MSP 34x5G
25
21HS-50H
DESCRIPTION OF SCHEMATIC DIAGRAM
SAFETY NOTE: 1. DISCONNECT THE AC PLUG FROM THE AC OUTLET BEFORE REPLACING PARTS. 2. SEMICONDUCTOR HEAT SINKS SHOULD BE REGARDED AS POTENTIAL SHOCK HAZARDS WHEN THE CHASSIS IS OPERATING. IMPOTANT SAFETY NOTE: PARTS MARKED WITH « ! » ( ) ARE IMPORTANT FOR MAINTAINING THE SAFETY OF THE SET. BE SURE TO REPLACE THESE PARTS WITH SPECIFIED ONES FOR MAINTAINING THE SAFETY AND PERFORMANCE OF THE SET.
NOTE: 1. The unit of resistance «ohm»is omitted (K=1000 ohms. M= Megaohm). 2. All resistors are 1/16 watt. unless otherwise noted. 3. All capacitors are µF, unless otherwise noted (P= µµF). 4. The capacitor with Part No. RC-FZ9XXXBMNJ is designed to with stand 63V. 5. The capacitor with Part No. RC-FZ4XXXBMNJ is designed to with stand 50V.
SERVICE PRECAUTION: THE AREA ENCLOSED BY THIS LINE ( ) IS DIRECTLY CONNECTED WITH AC MAINS VOLTAGE. WHEN SERVICING THE AREA, CONNECT AN ISOLATING TRANSFORMER BETWEEN TV RECEIVER AND AC LINE TO ELIMINATE HAZARD OF ELECTRIC SHOCK. WAVEFORM MEASUREMENT CONDITION: Colour bar genetator signal of 70 dB from RF input.
CAUTION This circuit diagram is original one, therefore there may be slight difference from yours.
WAVEFORMS:
26
21HS-50H
27
21HS-50H
SCHEMATIC DIAGRAM OF MOTHER UNIT (F7340N4, 01 Version)
I
H
G
F
E
D
C
B
Page 29
A
1
2
3
4
5
6
7
28
21HS-50H
SCHEMATIC DIAGRAM OF MOTHER UNIT (F7340N4, 01 Version)
I
H
G
F
E
D
C
B
Page 30
Page 28
A
8
9
10
11
12
13
14
29
21HS-50H
SCHEMATIC DIAGRAM OF MOTHER UNIT (F7340N4, 01 Version)
I
H
G
F
E
D
C
Page 29
B
A
8
9
10
11
12
13
14
30
21HS-50H
SCHEMATIC DIAGRAM OF CRT (F7341N0, 00 Version)
I
H
G
F
E
D
C
B
A
1
2
3
4
5
6
7
31
21HS-50H
CRT UNIT BLOCK DIAGRAM
I
H
G
F
E
D
C
B
A
1
2
3
4
5
6
7
32
21HS-50H
MOTHER UNIT BLOCK DIAGRAM
I
H
G
F
E
D
C
B
A
1
2
3
4
5
6
7
33
21HS-50H
TROUBLESHOOTING TABLES.
NO RASTER
Check F701. Abnormal Check R701 Q701. and IC701 Normal Check T701 pin16 voltage. (Approx. 290V at 220V AC) Normal Check Secondary Main+B. (Approx. 110V) YES Check CRT connector K1K5 bias. Normal Check C878. Abnormal Check IC801.
Blown out. Replace the fuse. The fuse is again blown out. Check IC701,D701,D702, D703,D704 and C705.
Abnormal Check D758,IC702,IC753 and D762. Normal Check R615.
Normal D1001 (Power LED Bright Red) turns on. NO NO D1001 (Power LED Dark Red) turns on
D1001 turns on brightly and darkly. (Bus error)
Checking the protector circuit.
NVM (IC1002) See many often D1001 flashes in red. This indicates which IC to check up. TV PROCESSOR (IC801) SOUND PROCESSOR (IC3001) TUNER (TU201)
34
21HS-50H
TROUBLESHOOTING TABLES.
NEITHER VERTICAL NOR HORIZONTAL SYNCHRONIZATION
CIRCUIT TO BE CHECKED: Sync. Separator Circuit. Check pin33 and 34 of IC801.
DEFECTIVE VERTICEL AMP. AND VERTICAL LINEARITY
Readjusted vertical size. (Bass Data)
Vertical linearity and size is abnormal.
Check R502,R505
NO VERTICAL SCAN
Check IC501 bias. Normal Abnormal
Check C502 and C514.
Check IC501.
NO SPECIFIC COLOUR
NO YES
Is some colour produced in B/W broadcast reception? Check IC801,R801,R802, R803,D804,D805,D806 and Q801.
YES
Is the white balance properly adjusted?
NO
Readjusted the white balance.
The picture colour is cyan.
The picture colour is magenta.
The picture colour is yellow.
Check Q870,Q885 and their adjacent circuits.
Check Q871,Q883 and their adjacent circuits.
Check Q872,Q887 and their adjacent circuits.
35
21HS-50H
TROUBLESHOOTING TABLES.
NO PICTURE, NO SOUND
CIRCUITS TO BE CHECKED: Tuner. PIF. Automatic Gain Control. 5V, 32V Power Source.
Does the noise level increase at max. Contrast,Brightness and Sound controls?
Noise increase but no signal is received.
No snow noise.
Check the tuner supply voltage LB and HB must be approx. 5V, BT must be approx. 32V,and CH preset data check.
Does noise or signal appear at pin40 of IC801?
NO YES
Normal
Does noise or signal appear at pin38 of IC801?
NO YES
Check IC801 and its related circuit.
Check the tuner AGC at TP201. Normal Abnormal
Does noise or signal appear at pin23 and 24 of IC801?
NO YES
Check Q401 Q402 and related circuit.
Check pin38 of IC801.
Check pin27 of IC801,Tuner and related circuit.
Check pin1,2 of SF201,Tuner and related circuit.
Check pin37 of IC801 and related circuit.
NO SOUND NO SOUND
CIRCUITS TO BE CHECKED: CIRCUITS TO BE CHECKED: Audio Output Circuit. Audio Output Circuit. Does signal appear Does signal appear at pin6 of IC303?
YES NO NO
at pin6 of IC302/303? YES
NO
Check IC801 and Check IC3001 and its related circuit. its related circuit.
NO
Check Speaker.
Check Speaker.
Check IC303 and peripheralIC302/303 and Check circuit.
peripheral circuit.
36
21HS-50H
PARTS LISTING
REPLACEMENT PARTS
Replacement parts which have special safety characteristics are identified in this manual. Electrical components having such features are identified by in the Replacement Part List. The use of a substitute replacement part which does not have the same safety characteristics as the factory recommended is not permitted. Replacement parts not shown in this service manual may create shock fire, or other hazards.
REF No. PARTS
D D D D D D D D D D D D D D D D D D D D D D D D D D D D D D D D D D D D D D D D D D D D D D D 0456 0457 0501 0502 0503 0504 0505 0507 0508 0509 0510 0601 0602 0603 0604 0605 0606 0607 0607 0608 0609 0610 0611 0612 0614 0615 0631 0632 0701 0702 0703 0704 0705 0708 0709 0751 0752 0753 0755 0756 0758 0759 0804 0805 0806 0807 1001 RH-EX1399CEZZ RH-EX1399CEZZ RH-DX0131CEZZ RH-DX0441CEZZ RH-EX0684GEZZ RH-EX0684GEZZ RH-DX0131CEZZ RH-EX0603GEZZ RH-DX0045BMZZ RH-DX0045BMZZ RH-EX0627GEZZ RH-DX0302CEZZ RH-DX0045BMZZ RH-DX0131CEZZ RH-DX0045BMZZ RH-DX0045BMZZ RH-DX0045BMZZ RH-EX0652GEZZ RH-EX0653GEZZ RH-DX0577BMZZ VHD1SS244//-1 RH-DX0045BMZZ RH-EX0615GEZZ RH-DX0045BMZZ RH-DX0045BMZZ RH-DX0045BMZZ RH-EX0627GEZZ RH-DX0045BMZZ RH-DX0571BMZZ RH-DX0571BMZZ RH-DX0571BMZZ RH-DX0571BMZZ VHD1SS244//-1 RH-DX0045BMZZ RH-EX0656GEZZ RH-DX0302CEZZ RH-DX0064GEZZ RH-EX0612GEZZ RH-DX0045BMZZ RH-EX0615GEZZ RH-DX0468CEZZ RH-DX0045BMZZ RH-EX1399CEZZ RH-EX1399CEZZ RH-EX1399CEZZ RH-EX1399CEZZ RH-PX0013PEZZ
DESCRIPTION
* SN CODE EX CODE
AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AB AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AB AB AB AB AA AA AB AA AA AA AA AB AA AB AA AA AA AA AA AE AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AB AC AA AA AA AC AA AB AB AB AB AB
HOW TO ORDER REPLACEMENT PARTS
To have your order completed promplty and corretly please supply the following information. 1. MODEL NUMBER 3. PART NO. 5. CODE 2. REF. NO. 4. DESCRIPTION 6. QUANTITY
MARK *: SPARE PARTS DELIVERY SECTION REF No. PARTS
! !
DESCRIPTION PICTURE TUBE
* SN CODE EX CODE
BN AH CD AP
VB51EFS83912E RCILG0408BMZZ
CRT 21" THA51EFS83X391+DYW S DEGUSSING COIL TODAIMUSEN S
PRINTED WIRING BOARDS (Not replacement item)
DUNTK7340CJV3 DUNTK7341BMV3 ADJUST CHASSIS 21HS50H CRT UNIT INS A 21HS50H S S -----
PWB-A
TU 0201 VTUCTF5511+++
MOTHER UNIT TUNER
TUNER THOMSON S AA AZ
INTEGRATED CIRCUITS
IC 0303 IC 0501 IC 0601 IC 0701 IC 0702 IC 0751 IC 0801 IC 1002 IC 3001 VHIAN7523++-1 VHIAN5522++-1 VHIKA7808AP-1 VHITEA1507/-1 RH-FX0008GEZZ VHITA48M033-1 RH-IXA096WJZZ VHIM24C08W6-1 VHIMSP3415G-1 IC AN7523 MATSUSHITA S IC AN5523 MATSUSHITA S S IC KIA7808API KOREA ELECTRONIC IC TEA1507P/N1 PHILIPS S P/COUPLER RANK-S SHARP S IC TA48M033F(S) TOSHIBA S IC TDA9350 P/N TEXT 64K STEREO S IC M24C08-WMN6T ST MICRO S IC S AC AC AA AC AA AB AA AB AA AH AG AE AH AD AF BF AF BC
!
TRANSISTORS
Q Q Q Q Q Q Q Q Q Q Q Q Q Q Q Q Q Q Q Q 0331 0351 0352 0401 0402 0451 0501 0502 0601 0602 0603 0604 0605 0631 0701 0752 0753 0754 1005 1006 VS2SC2412KQ-1 VS2SC2412KQ-1 VS2SC2412KQ-1 VS2SC2412KQ-1 VS2SC2412KQ-1 VS2SC2412KQ-1 VS2SC2412KQ-1 VS2SC2412KQ-1 VS2SC2482//-1 VS2SD2586//1E VS2SC2412KQ-1 VS2SC4793//-1 VS2SA1037KQ-1 VS2SA1037KQ-1 VSSTP4NC80Z1E VS2SC1815GW-1 VS2SC2412KQ-1 VS2SC2412KQ-1 VS2SC2412KQ-1 VS2SC2412KQ-1 TRT 2SC2412 ROHM TRT 2SC2412 ROHM TRT 2SC2412 ROHM TRT 2SC2412 ROHM TRT 2SC2412 ROHM TRT 2SC2412 ROHM TRT 2SC2412 ROHM TRT 2SC2412 ROHM TRT 2SC2482 TOSHIBA TRT 2SD2586 TOSHIBA TRT 2SC2412 ROHM TRT C4793 TOSHIBA TRT BC807 SMD TRT BC807 SMD MOS FET STP4NC80ZFP TOMEN TRT NPN 60V 150MA 400MW TRT 2SC2412 ROHM TRT 2SC2412 ROHM TRT 2SC2412 ROHM TRT 2SC2412 ROHM S S S S S S S S S S S S S S S S S S S S AA AA AA AA AA AA AA AA AA AA AA AB AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AB AR AA AE AA AA AH AA AA AA AA AA
ZENER DIODE UDZSTE-179.1B WAK S S ZENER DIODE UDZSTE-179.1B WAK DIODE EU-1 SANKEN S DIODE IN4002G23 GENERAL INSTRS ZENER DIODE MTZJ39BT ROHM S ZENER DIODE MTZJ39BT ROHM S DIODE EU-1 SANKEN S Z.DIODE MTZJ 3.9A S DIODE 1N4148 S DIODE 1N4148 S ZENER DIODE MTZJ8.2BT ROHM S DIODE UZA S DIODE 1N4148 S DIODE EU-1 SANKEN S DIODE 1N4148 S DIODE 1N4148 S DIODE 1N4148 S ZENER DIODE MTZJ18B ROHM S DIODE ZENER MTZJ18C ROHM S DIODE 1N4935 ACPA S SW DIODE 1SS244T-72 S DIODE 1N4148 S ZENER DIODE 5.6V S DIODE 1N4148 S DIODE 1N4148 S DIODE 1N4148 S ZENER DIODE MTZJ8.2BT ROHM S DIODE 1N4148 S DIODE 1N4005 ACPA S DIODE 1N4005 ACPA S DIODE 1N4005 ACPA S DIODE 1N4005 ACPA S SW DIODE 1SS244T-72 S DIODE 1N4148 S ZENER DIODE MTZJ20C ROHM S DIODE UZA S DIODE AK04V1 SANKEN S ZENER DIODE MTZJ5.1BT ROHM S DIODE 1N4148 S ZENER DIODE 5.6V S DIODE S3L20U SHINDENGEN S DIODE 1N4148 S S ZENER DIODE UDZSTE-179.1B WAK S ZENER DIODE UDZSTE-179.1B WAK S ZENER DIODE UDZSTE-179.1B WAK S ZENER DIODE UDZSTE-179.1B WAK LED L-53ID-13.95L/F S
PACKAGED CIRCUITS
PR 0701 X 1001 X 3001 RMPTP0001BMZZ RCRSB0300CEZZ RCRSB0249GEZZ PTC B59250-C1080-B70 S S CRYSTAL HC-49/U-S 12000KHz-A1 M X'TAL 18.432MHZ (KDS) S AA AB AA AD AF AE
COILS
L L L L L L L L L L L L L L L L L L L L 0201 0204 0308 0351 0352 0353 0354 0403 0451 0602 0701 0801 0802 1002 3001 3002 3003 3030 3050 3060 VP-DF270K0000 VP-DF270K0000 VP-CF3R3K0000 VP-DF3R3K0000 VP-DF3R3K0000 VP-DF3R3K0000 VP-DF3R3K0000 VP-XF120K0000 VP-DF3R3K0000 RCILP0225CEZZ RCILF0111BMZZ VP-XF100K0000 VP-XF100K0000 VP-XF100K0000 VP-DF100K0000 VP-DF100K0000 VP-DF100K0000 VP-CF3R3K0000 VP-CF3R3K0000 VP-CF3R3K0000 PEAK COIL 27UH 10% PEAK COIL 27UH 10% PEAK COIL 3.3UH 10% PEAK COIL 3,3UH 10% PEAK COIL 3,3UH 10% PEAK COIL 3,3UH 10% PEAK COIL 3,3UH 10% PEAK COIL 12UH 10% 1/8W PEAK COIL 3,3UH 10% COIL SL_A TOKYO COIL HR-19043 PEAK COIL 10UH 10% 1/8W PEAK COIL 10UH 10% 1/8W PEAK COIL 10UH 10% 1/8W PEAK COIL 10UH 10% PEAK COIL 10UH 10% PEAK COIL 10UH 10% PEAK COIL 3.3UH 10% PEAK COIL 3.3UH 10% PEAK COIL 3.3UH 10% S S S S S S S S S S S S S S S S S S S S AA AA AB AB AB AB AB AA AB AA AE AA AA AA AA AA AA AB AB AB AB AB AB AB AB AB AB AA AB AD AL AA AA AA AA AA AA AB AB AB
DIODES
D D D D D D D 0201 0303 0351 0451 0452 0453 0454 RH-EX0676GEZZ RH-DX0045BMZZ RH-EX1399CEZZ RH-EX1399CEZZ RH-EX1399CEZZ RH-EX1399CEZZ RH-EX1399CEZZ ZENER DIODE MTZJ33CT ROHM S DIODE 1N4148 S S ZENER DIODE UDZSTE-179.1B WAK S ZENER DIODE UDZSTE-179.1B WAK S ZENER DIODE UDZSTE-179.1B WAK S ZENER DIODE UDZSTE-179.1B WAK S ZENER DIODE UDZSTE-179.1B WAK AA AA AA AA AA AA AA AA AA AB AB AB AB AB
!
37
21HS-50H
REF No. PARTS
CF 0401 SF 0201 RFILC0023CEZZ RFILC0283BMZZ
DESCRIPTION CERAMIC FILTERS
SOUND FILTER (TAPED) SAW FILTER J1980M SIEMENS
* SN CODE EX CODE
S S AA AF AD AM
REF No. PARTS
C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C 0531 0532 0533 0599 0602 0603 0604 0605 0606 0607 0608 0609 0610 0611 0614 0615 0616 0617 0619 0621 0622 0631 0632 0633 0701 0702 0703 0704 0705 0707 0708 0709 0710 0712 0713 0716 0751 0752 0753 0754 0755 0756 0757 0758 0759 0761 0762 0764 0765 0767 0801 0803 0804 0805 0806 0807 0808 0809 0810 0811 0812 0813 0814 0815 0817 0818 0819 0822 0823 1001 1002 1006 1009 1011 VCKYCY1HB102K VCKYCY1HB102K VCQYTA1HM104J VCKYPA1HB102K VCEA0A1CW477M VCEA0A1CW107M VCKYPA1HF103Z VCEA0A1AW227M VCEA0A1CW107M VCKYPA1HF103Z VCKYCY1EF104Z VCKYPA2HB102K VCFYSB2EB823J VCFPVC3CA912H VCFPVC2DB564J RC-EZ0724CEZZ VCQYTA1HM104J VCEA0A1HW105M VCEA0A1HW106M VCEA0A2CW105M VCEA0A1CW227M VCKYCY1EF104Z VCKYCY1HB222K VCEA0A1CW107M RC-FZ0176BMZZ RC-KZ0029CEZZ RC-KZ0029CEZZ RC-KZ0029CEZZ RC-EZ0150BMZZ VCEA0A1EW107M VCQYTA1HM104J VCFYFA1HA474J RC-KZ0040CEZZ RC-KZ0105GEZZ VCKYPA1HB102K VCKYPA2HB102K RC-KZ0299CEZZ RC-EZ0724CEZZ VCKYPA1HB102K VCEA0A1CW108M VCEA0A1CW227M VCEA0A0JW227M VCKYPA2HB102K VCEA0A1EW108M VCKYPA1HB102K VCKYCY1EF104Z VCCCPA1HH680J VCEA0A1EW107M VCEA0A1CW107M VCKYCY1HF103Z VCEA0A1CW227M VCFYFA1HA224J VCFYFA1HA224J VCKYCY1HB222K VCEA0A1HW105M VCKYCY1HB472K VCKYCY1HF223Z VCEA0A1CW106M VCEA0A1HW474M VCKYCY1HB102K VCKYCY1HB102K VCKYCY1HB102K VCKYCY1HB561K VCEA0A1CW227M VCKYCY1HF103Z VCKYCY1HF103Z VCEA0A1CW227M VCKYCY1HF103Z VCKYCY1HF103Z VCCCCY1HH220J VCCCCY1HH220J VCKYCY1HF223Z VCEA0A0JW107M VCEA0A0JW107M
DESCRIPTION
* SN CODE EX CODE
AA AA AA AA AA AA AA -AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AC AC AC AA AA AA AA AD AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AB AA AB AA AA -AA AA AA AA AB AC AC AG AB AA AA AB AA AA AA AA AB AC AC AC AM AA AB AB AD AC AA AA AC AG AA AB AA AA AA AC AA AA AA AA AA AA AA AC AC AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA
TRANSFORMERS
! !
T 0601 T 0602 T 0701
RTRNZ0026PEZZ RTRNF2053CEZZ RTRNW0005CEZZ
DRIVER TRANSFORMER FBT BSC21-2643S SHENZHEN SMT TABUCHI
S S S
AA AM AA
AF AY AP
CAPACITORS
C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C 0201 0202 0204 0206 0207 0208 0209 0210 0211 0212 0215 0302 0305 0307 0308 0311 0314 0315 0318 0320 0322 0323 0324 0325 0326 0331 0341 0342 0344 0349 0351 0352 0354 0356 0357 0358 0359 0360 0361 0362 0363 0402 0403 0404 0431 0432 0433 0451 0453 0502 0504 0505 0506 0507 0508 0509 0511 0512 0513 0514 0515 0521 0522 VCEA0A1CW476M VCEA0A1AW107M VCEA0A1HW106M VCKYCY1HF223Z VCKYCY1HB472K VCKYCY1HB821K VCKYCY1EF104Z VCCCCY1HH220J VCKYPA1HF103Z VCKYPA1HF103Z VCCCCY1HH220J VCEA0A1CW106M VCEA0A1EW337M VCEA0A1CW226M VCKYCY1HF103Z VCKYCY1HB102K VCKYCY1HB102K VCKYCY1HB102K VCEA0A1CW106M VCKYCY1HB102K VCKYCY1HF103Z VCKYCY1HB102K VCKYCY1HB102K VCCSPA1HL221J VCCSPA1HL221J VCEA0A1HW225M VCKYCY1HB332K VCEA0A1CW106M VCKYCY1HF103Z VCKYCY1HF103Z VCKYCY1HB102K VCEA0A1CW107M VCEA0A1CW107M VCKYCY1HB102K VCEA0A1CW107M VCEA0A1CW107M VCKYCY1HB102K VCEA0A1CW106M VCKYCY1HB102K VCEA0A1CW106M VCKYCY1HB102K VCCCCY1HH220J VCKYCY1HF103Z VCEA0A1CW106M VCKYCY1HF223Z VCKYCY1HB102K VCKYCY1EF104Z VCEA0A1CW106M VCKYCY1HF103Z VCEA0A1EW477M VCKYPA1HB102K VCEA0A1HW107M VCKYPA1HB102K VCKYCY1HF103Z RC-FZ0272CEZZ VCQYTA2AA563J VCKYPA1HB102K VCKYCY1HF103Z VCKYPA2HB102K VCEA0A1EW477M VCQYTA1HM103J VCKYCY1HB102K VCKYPA1HB102K ELEC C 47UF 20% 16V S ELEC C 100UF 20% 10V S ELEC C 10UF 20% 50V S SC CAPACITOR 0.022UF 50V TAPE S S.CHIP CAP 4700PF/50V T S S GRM39B 821K 50 (1608)SMD CAPAC S CHIP TAPE CAP 0.1UF/25V S S. CHIP CAP 22PF/50V TAPED S C.CAPACITOR 0.01U-F 50V S C.CAPACITOR 0.01U-F 50V S S. CHIP CAP 22PF/50V TAPED S ELEC C 10UF 20% 16V S ELEC C 330UF 20% 25V S ELEC C 22UF 20% 16V S CHIP CAP 0.01UF/50V S S. CHIP CAP 0.001UF/50V S S. CHIP CAP 0.001UF/50V S S. CHIP CAP 0.001UF/50V S ELEC C 10UF 20% 16V S S. CHIP CAP 0.001UF/50V S CHIP CAP 0.01UF/50V S S. CHIP CAP 0.001UF/50V S S. CHIP CAP 0.001UF/50V S CERAM C 220PF 5% 50V S CERAM C 220PF 5% 50V S ELEC C 2,2UF 20% 50V S s.chip cap 3300pf /50v S ELEC C 10UF 20% 16V S CHIP CAP 0.01UF/50V S CHIP CAP 0.01UF/50V S S. CHIP CAP 0.001UF/50V S ELEC C 100UF 20% 16V S ELEC C 100UF 20% 16V S S. CHIP CAP 0.001UF/50V S ELEC C 100UF 20% 16V S ELEC C 100UF 20% 16V S S. CHIP CAP 0.001UF/50V S ELEC C 10UF 20% 16V S S. CHIP CAP 0.001UF/50V S ELEC C 10UF 20% 16V S S. CHIP CAP 0.001UF/50V S S. CHIP CAP 22PF/50V TAPED S CHIP CAP 0.01UF/50V S ELEC C 10UF 20% 16V S SC CAPACITOR 0.022UF 50V TAPE S S. CHIP CAP 0.001UF/50V S S CHIP TAPE CAP 0.1UF/25V S ELEC C 10UF 20% 16V S CHIP CAP 0.01UF/50V S ELEC C 470UF 20% 25V S C.CAPACITOR 1000PF/50V S ELEC C 100UF 20% 50V S C.CAPACITOR 1000PF/50V S CHIP CAP 0.01UF/50V S C POL P 0,39UF 100V S POL FILM C 56NF 5% 100V S C.CAPACITOR 1000PF/50V S CHIP CAP 0.01UF/50V S CERAM C 1NF 10% 500V S ELEC C 470UF 20% 25V S F. CAPACITOR 0.01UF/50V S S. CHIP CAP 0.001UF/50V S C.CAPACITOR 1000PF/50V S AA -AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA -AA AA AA AA AA AA AA AA AA AA AB AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AB AA AA AA AA AC AB AA AA AA AB AA AA AA
!
!
!
!
S. CHIP CAP 0.001UF/50V S S. CHIP CAP 0.001UF/50V S F. CAPACITOR 0.1 UF 50 V S C.CAPACITOR 1000PF/50V S ELEC C 470UF 20% 16V S ELEC C 100UF 20% 16V S C.CAPACITOR 0.01U-F 50V S ELEC C 220UF 20% 10V S ELEC C 100UF 20% 16V S C.CAPACITOR 0.01U-F 50V S S CHIP TAPE CAP 0.1UF/25V S CERAM C 1NF 10% 500V S POL FILM C 82NF 5% 100V S PP FILM C 9,1NF 50% 1600V S PP FILM C 560NF 5% 200V S ELEC C KMF160VB-100MMC NICHICS F. CAPACITOR 0.1 UF 50 V S ELEC C 1UF 20% 50V S ELEC C 10UF 20% 50V S ELEC C 1UF 20% 160V S E CAPACITOR 220UF 16V 6.3x11 S S CHIP TAPE CAP 0.1UF/25V S S CHIP CAPACITOR 0.0022UF/50V TS ELEC C 100UF 20% 16V S POL C B81130 100NF 275V X2 S CERAM C 10NF 80,20% 250V S CERAM C 10NF 80,20% 250V S CERAM C 10NF 80,20% 250V S ELEC C 100uF 400V LPN100M2GN S E. CAPACITOR 100UF 25V 6.3x11 S F. CAPACITOR 0.1 UF 50 V S FILM CAPACITOR 474 MAT S CERAM C 820PF 2KV S C. CAP 2200PF/4KV-KX S C.CAPACITOR 1000PF/50V S CERAM C 1NF 10% 500V S CERAM C DE1105-979BN821K2K-A3S ELEC C KMF160VB-100MMC NICHICS C.CAPACITOR 1000PF/50V S ELEC C 1000MF 16V 10X16MM S E CAPACITOR 220UF 16V 6.3x11 S E CAPACITOR 220UF/6.3V-5X11 S CERAM C 1NF 10% 500V S ELEC C 1000MF 25V 10X16MM S C.CAPACITOR 1000PF/50V S S CHIP TAPE CAP 0.1UF/25V S CERAM C 68PF 5% 50V S ELEC C 100UF 20% 25V S ELEC C 100UF 20% 16V S CHIP CAP 0.01UF/50V S E CAPACITOR 220UF 16V 6.3x11 S PP FILM C 220NF 5% 50V S PP FILM C 220NF 5% 50V S S CHIP CAPACITOR 0.0022UF/50V TS ELEC C 1UF 20% 50V S S.CHIP CAP 4700PF/50V T S SC CAPACITOR 0.022UF 50V TAPE S ELEC C 10UF 20% 16V S ELEC C 0,47UF 20% 50V S S. CHIP CAP 0.001UF/50V S S. CHIP CAP 0.001UF/50V S S. CHIP CAP 0.001UF/50V S S. CAPACITOR 560PF/50V S E CAPACITOR 220UF 16V 6.3x11 S CHIP CAP 0.01UF/50V S CHIP CAP 0.01UF/50V S E CAPACITOR 220UF 16V 6.3x11 S CHIP CAP 0.01UF/50V S CHIP CAP 0.01UF/50V S S. CHIP CAP 22PF/50V TAPED S S. CHIP CAP 22PF/50V TAPED S SC CAPACITOR 0.022UF 50V TAPE S ELEC C 100UF 20% 6,3V S ELEC C 100UF 20% 6,3V S
38
21HS-50H
REF No. PARTS
C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C 1012 1013 1014 1015 1016 1017 1018 3001 3003 3004 3005 3006 3007 3008 3011 3012 3013 3014 3015 3016 3017 3018 3019 3020 3021 3022 3023 3024 3025 3026 3027 3028 3029 3030 VCKYCY1EF104Z VCKYCY1HF103Z VCEA0A0JW107M VCEA0A1CW106M VCEA0A1CW476M VCKYCY1HF103Z VCKYCY1HF103Z VCKYCY1HF103Z VCKYCY1HB102K VCKYCY1HB471K VCEA0A1CW107M VCEA0A1HW335M VCEA0A1CW106M VCKYCY1EF104Z VCKYCY1EF104Z VCKYCY1EF104Z VCKYCY1EF104Z VCKYCY1EF104Z VCEA0A1CW106M VCCCCY1HH101J VCCCCY1HH560J VCCCCY1HH560J VCCCCY1HH1R5C VCCCCY1HH1R5C VCKYCY1EF104Z VCKYCY1HB102K VCKYCY1HB471K VCEA0A1CW106M VCKYCY1HB102K VCEA0A1HW105M VCEA0A1HW105M VCKYCY1HF103Z VCEA0A1CW106M VCKYCY1HB151K
DESCRIPTION
* SN CODE EX CODE
AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AC AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA
REF No. PARTS
R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R 0455 0456 0457 0458 0459 0460 0461 0490 0491 0501 0502 0503 0504 0505 0507 0509 0511 0512 0513 0514 0515 0516 0517 0518 0531 0532 0533 0603 0604 0605 0606 0607 0608 0609 0610 0611 0612 0613 0614 0615 0616 0618 0619 0620 0621 0623 0624 0625 0626 0627 0629 0630 0631 0632 0633 0634 0636 0637 0638 0639 0640 0701 0706 0707 0708 0710 0711 0712 0713 0715 0716 0718 0752 0753 0758 VRD-RA2EE750J VRD-RA2EE750J VRD-RA2EE750J VRS-CY1JF103J VRD-RA2EE750J VRD-RA2EE750J VRD-RA2BE224J VRS-CY1JF000J VRS-CY1JF000J VRD-RA2BE392J VRN-VV3DB2R7J VRD-RA2HD331J VRS-CY1JF181J VRD-RA2BE1R0J VRS-CY1JF181J VRD-RA2BE102J VRD-RA2HD102J VRD-RA2BE100J VRD-RA2BE103J VRS-CY1JF103J VRS-CY1JF153J VRS-CY1JF153J VRS-CY1JF223J VRS-CY1JF334J VRD-RA2BE101J VRD-RA2BE101J VRD-RA2BE393J VRD-RA2BE102J VRD-RA2HD472J VRS-KT3LB332J VRD-RA2HD102J VRD-RA2BE104J VRN-RV3ABR82J VRD-RA2HD101J VRS-CY1JF102J VRS-CY1JF103J VRD-RA2BE331J VRD-RA2HD184J VRD-RA2HD472J VRD-RA2HD472J VRD-RA2HD182J VRD-RA2BE123J VRS-CY1JF000J VRD-RA2HD100J VRD-RA2HD820J VRG-RL2HB562J VRD-RA2BE123J VRD-RA2BE103J VRS-CY1JF562J VRS-CY1JF103J VRD-RA2EE151J VRD-RA2BE101J VRD-RA2BE391J VRD-RA2BE273J VRS-CY1JF822J VRS-CY1JF102J VRS-CY1JF154J VRS-CY1JF333J VRS-CY1JF221J VRD-RA2BE333J VRD-RA2BE101J VRW-KP3HC5R6K VRD-RA2BE122J VRD-RA2BE393J VRD-RA2BE102J VRN-VV3ABR27J VRD-RA2BE270J VRD-RA2HD100J VRD-RA2BE394J VRC-UA2HG825K VRC-UA2HG825K VRD-RA2BE824J VRD-RA2HD102J VRN-VV3DB5R6J VRN-VV3DB5R6J
DESCRIPTION
RES 75 OHM 5% 1/4W RES 75 OHM 5% 1/4W RES 75 OHM 5% 1/4W S.C. RESISTOR 10K OHM RES 75 OHM 5% 1/4W RES 75 OHM 5% 1/4W RES 220KOHM 5% 1/8W S. CHIP RES. 0-OHM TAPED S. CHIP RES. 0-OHM TAPED RES 3,9KOHM 5% 1/8W MET FILM R 2,7 OHM 5% 2W RES 330 OHM 5% 1/2W S CHIP RES. 180-OHM TAPED RES 1 OHM 5% 1/8W S CHIP RES. 180-OHM TAPED RES 1KOHM 5% 1/8W RES 1KOHM 5% 1/2W RES 10 OHM 5% 1/8W RES 10KOHM 5% 1/8W S.C. RESISTOR 10K OHM S CHIP RES. 15K-OHM TAPED S CHIP RES. 15K-OHM TAPED S.CHOP REG 22K-OHM T S. CHIP RES. 330K-OHM TAPED RES 100 OHM 5% 1/8W RES 100 OHM 5% 1/8W RES 39KOHM 5% 1/8W RES 1KOHM 5% 1/8W RES 4.7KOHM 5% 1/2W MET OX RES 3,3KOHM 5% 3W RES 1KOHM 5% 1/2W RES 100KOHM 5% 1/8W MET FILM R 0,82 OHM 5% 1W RES 100 OHM 5% 1/2W S.CHIP RES TAPE 1K OHM S.C. RESISTOR 10K OHM RES 330 OHM 5% 1/8W RES 180KOHM 5% 1/2W RES 4.7KOHM 5% 1/2W RES 4.7KOHM 5% 1/2W RES 1,8KOHM 5% 1/2W RES 12KOHM 5% 1/8W S. CHIP RES. 0-OHM TAPED RES 10 OHM 5% 1/2W RES 82 OHM 5% 1/2W FUS RES 5,6KOHM 5% 1/2W RES 12KOHM 5% 1/8W RES 10KOHM 5% 1/8W S. CHIP RES. 5.6K-OHM TAPED S.C. RESISTOR 10K OHM RES 150 OHM 5% 1/4W RES 100 OHM 5% 1/8W RES 390 OHM 5% 1/8W RES 27KOHM 5% 1/8W S. CHIP RES. 8.2K-OHM TAPED S.CHIP RES TAPE 1K OHM S CHIP RES. 150K-OHM TAPED S. CHIP RES. 33K-OHM TAPED S. CHIP RES. 220-OHM TAPED RES 33KOHM 5% 1/8W RES 100 OHM 5% 1/8W WOUND RES 5,6 OHM 10% 5W RES 1,2KOHM 5% 1/8W RES 39KOHM 5% 1/8W RES 1KOHM 5% 1/8W MET FILM R .27 OHM 5% 1W RES 27 OHM 5% 1/8W RES 10 OHM 5% 1/2W RES 390KOHM 5% 1/8W SOLID R 8,2MOHM 10% 1/2W SOLID R 8,2MOHM 10% 1/2W RES 820KOHM 5% 1/8W RES 1KOHM 5% 1/2W MET FILM R 5.6 OHM 5% 2W MET FILM R 5.6 OHM 5% 2W
* SN CODE EX CODE
S S S S S S S S S S S S S S S S S S S S S S S S S S S S S S S S S S S S S S S S S S S S S S S S S S S S S S S S S S S S S S S S S S S S S S S S S S S AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AB AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AB AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AD AA AA AB AA AA AA AA AA AA AA AA AA AA AA AA AB AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AC AA AA AA AA AA AA AA AA AA AA AA AB AB
S CHIP TAPE CAP 0.1UF/25V S CHIP CAP 0.01UF/50V S ELEC C 100UF 20% 6,3V S ELEC C 10UF 20% 16V S ELEC C 47UF 20% 16V S CHIP CAP 0.01UF/50V S CHIP CAP 0.01UF/50V S CHIP CAP 0.01UF/50V S S. CHIP CAP 0.001UF/50V S S GRM39B 471K 50 (1608)SMD CAPAC ELEC C 100UF 20% 16V S ELEC C 3,3UF 20% 50V S ELEC C 10UF 20% 16V S S CHIP TAPE CAP 0.1UF/25V S S CHIP TAPE CAP 0.1UF/25V S S CHIP TAPE CAP 0.1UF/25V S S CHIP TAPE CAP 0.1UF/25V S S CHIP TAPE CAP 0.1UF/25V S ELEC C 10UF 20% 16V S S. CHIP CAP 100PF/50V TAPED S S. CHIP CAP 56PF/50V TAPE S S. CHIP CAP 56PF/50V TAPE S GRM39CK 1R5C 50 (1608)SMD CAPS GRM39CK 1R5C 50 (1608)SMD CAPS S CHIP TAPE CAP 0.1UF/25V S S. CHIP CAP 0.001UF/50V S S GRM39B 471K 50 (1608)SMD CAPAC ELEC C 10UF 20% 16V S S. CHIP CAP 0.001UF/50V S ELEC C 1UF 20% 50V S ELEC C 1UF 20% 50V S CHIP CAP 0.01UF/50V S ELEC C 10UF 20% 16V S CAPACITOR GRM39B 151K 50 (1608S
RESISTORS
R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R 0201 0202 0208 0209 0302 0303 0305 0306 0331 0332 0333 0341 0351 0352 0354 0355 0356 0357 0359 0360 0362 0363 0364 0365 0366 0367 0401 0403 0404 0405 0406 0407 0408 0409 0451 0452 0453 0454 VRD-RA2BE332J VRS-CY1JF681J VRS-CY1JF102J VRS-CY1JF391J VRS-CY1JF472J VRD-RA2BE102J VRD-RA2BE102J VRS-CY1JF392J VRS-CY1JF103J VRS-CY1JF473J VRD-RA2BE103J VRS-CY1JF101J VRS-CY1JF000J VRS-CY1JF104J VRS-CY1JF000J VRS-CY1JF104J VRS-CY1JF102J VRS-CY1JF103J VRS-CY1JF102J VRS-CY1JF103J VRS-CY1JF472J VRS-CY1JF104J VRS-CY1JF472J VRS-CY1JF104J VRS-CY1JF561J VRS-CY1JF561J VRS-CY1JF101J VRS-CY1JF102J VRD-RA2BE101J VRS-CY1JF181J VRS-CY1JF102J VRD-RA2BE101J VRD-RA2BE101J VRD-RA2BE102J VRD-RA2EE750J VRS-CY1JF104J VRS-CY1JF223J VRS-CY1JF562J RES 3,3KOHM 5% 1/8W S S. CHIP RES. 680-OHM TAPED S S.CHIP RES TAPE 1K OHM S SURFACE MOUNT CHIP RESISTORS S. RES. 4.7K OHM TAPED S RES 1KOHM 5% 1/8W S RES 1KOHM 5% 1/8W S S. CHIP RES. 3.9K-OHM TAPED S S.C. RESISTOR 10K OHM S S. CHIP RES 47K-OHM TAPED S RES 10KOHM 5% 1/8W S S. CHIP RES. 100-OHM TAPED S S. CHIP RES. 0-OHM TAPED S S. CHIP RES. 100K-OHM TAPED S S. CHIP RES. 0-OHM TAPED S S. CHIP RES. 100K-OHM TAPED S S.CHIP RES TAPE 1K OHM S S.C. RESISTOR 10K OHM S S.CHIP RES TAPE 1K OHM S S.C. RESISTOR 10K OHM S S. RES. 4.7K OHM TAPED S S. CHIP RES. 100K-OHM TAPED S S. RES. 4.7K OHM TAPED S S. CHIP RES. 100K-OHM TAPED S S. CHIP RES 560-OHM TAPED S S. CHIP RES 560-OHM TAPED S S. CHIP RES. 100-OHM TAPED S S.CHIP RES TAPE 1K OHM S RES 100 OHM 5% 1/8W S S CHIP RES. 180-OHM TAPED S S.CHIP RES TAPE 1K OHM S RES 100 OHM 5% 1/8W S RES 100 OHM 5% 1/8W S RES 1KOHM 5% 1/8W S RES 75 OHM 5% 1/4W S S. CHIP RES. 100K-OHM TAPED S S.CHOP REG 22K-OHM T S S. CHIP RES. 5.6K-OHM TAPED S AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA
!
! !
!
39
21HS-50H
REF No. PARTS
R 0761 R 0762 R 0763 R 0766 R 0768 R 0770 R 0771 R 0772 R 0773 R 0774 R 0801 R 0802 R 0803 R 0804 R 0805 R 0806 R 0807 R 0808 R 0809 R 1001 R 1002 R 1003 R 1004 R 1005 R 1006 R 1008 R 1009 R 1014 R 1015 R 1016 R 1017 R 1018 R 1019 R 1020 R 1022 R 1023 R 1024 R 1025 R 1026 R 1027 R 1028 R 1029 R 1033 R 1034 R 1035 R 1036 R 1037 R 1038 R 1040 R 1041 R 1042 R 1043 R 1044 R 1047 R 1048 R 1052 R 1053 R 1054 R 1056 R 1057 R 1058 R 3001 R 3002 R 3003 R 3004 R 3007 R 3008 R 3009 R 3010 R 3011 R 3012 RJ 0001 RJ 0002 RJ 0004 VRD-RA2BE152J VRD-RA2HD184J VRD-RA2BE822J VRD-RA2EE183J VRD-RA2HD124J VRD-RA2HD181J VRD-RA2HD181J VRS-CY1JF333J VRS-CY1JF153J VRS-CY1JF332J VRS-CY1JF101J VRS-CY1JF101J VRS-CY1JF101J VRS-CY1JF101J VRS-CY1JF223J VRS-CY1JF101J VRS-CY1JF101J VRS-CY1JF101J VRS-CY1JF101J VRS-CY1JF181J VRS-CY1JF221J VRS-CY1JF331J VRS-CY1JF681J VRS-CY1JF472J VRS-CY1JF101J VRS-CY1JF000J VRS-CY1JF000J VRD-RA2BE101J VRD-RA2BE101J VRD-RA2BE332J VRD-RA2BE101J VRD-RA2BE332J VRS-CY1JF101J VRS-CY1JF153J VRS-CY1JF101J VRD-RA2BE153J VRS-CY1JF101J VRS-CY1JF122J VRS-CY1JF224J VRS-CY1JF101J VRD-RA2BE101J VRS-CY1JF101J VRS-CY1JF101J VRD-RA2BE332J VRS-CY1JF101J VRD-RA2BE332J VRD-RA2BE101J VRS-CY1JF223J VRS-CY1JF152J VRS-CY1JF152J VRS-CY1JF000J VRS-CY1JF562J VRS-CY1JF000J VRS-CY1JF000J VRS-CY1JF391J VRS-CY1JF000J VRS-CY1JF000J VRS-CY1JF101J VRS-CY1JF103J VRS-CY1JF472J VRS-CY1JF101J VRD-RA2BE101J VRD-RA2BE101J VRD-RA2BE101J VRD-RA2BE101J VRS-CY1JF102J VRS-CY1JF103J VRS-CY1JF333J VRS-CY1JF103J VRS-CY1JF333J VRS-CY1JF103J VRS-CY1JF000J VRS-CY1JF000J VRS-CY1JF000J
DESCRIPTION
* SN CODE EX CODE
AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA
REF No. PARTS
RJ 0008 RJ 0009 RJ 0010 RJ 0011 RJ 0012 RJ 0019 RJ 0020 RJ 0024 RJ 0025 RJ 0026 RJ 0027 RJ 0029 RJ 0031 RJ 0033 RJ 0035 RJ 0036 RJ 0044 RJ 0046 RJ 0047 RJ 0048 RJ 0055 RJ 0056 RJ 0057 RJ 0058 RJ 0059 RJ 0061 RJ 0062 RJ 0064 RJ 0065 RJ 0067 RJ 0068 RJ 0070 RJ 0072 RJ 0075 RJ 0077 RJ 0078 RJ 0080 RJ 0081 RJ 0082 RJ 0085 VRS-CY1JF000J VRS-CY1JF000J VRS-CY1JF000J VRS-CY1JF000J VRS-CY1JF000J VRS-CY1JF000J VRS-CY1JF000J VRS-CY1JF000J VRS-CY1JF000J VRS-CY1JF000J VRS-CY1JF000J VRS-CY1JF000J VRS-CY1JF000J VRS-CY1JF000J VRS-CY1JF000J VRS-CY1JF000J VRS-CY1JF000J VRS-CY1JF000J VRS-CY1JF000J VRS-CY1JF000J VRS-CY1JF000J VRS-CY1JF000J VRS-CY1JF000J VRS-CY1JF000J VRS-CY1JF000J VRS-CY1JF000J VRS-CY1JF000J VRS-CY1JF000J VRS-CY1JF000J VRS-CY1JF000J VRS-CY1JF000J VRS-CY1JF000J VRS-CY1JF000J VRS-CY1JF000J VRS-CY1JF000J VRS-CY1JF000J VRS-CY1JF000J VRS-CY1JF000J VRS-CY1JF000J VRS-CY1JF000J
DESCRIPTION
S. CHIP RES. 0-OHM TAPED S. CHIP RES. 0-OHM TAPED S. CHIP RES. 0-OHM TAPED S. CHIP RES. 0-OHM TAPED S. CHIP RES. 0-OHM TAPED S. CHIP RES. 0-OHM TAPED S. CHIP RES. 0-OHM TAPED S. CHIP RES. 0-OHM TAPED S. CHIP RES. 0-OHM TAPED S. CHIP RES. 0-OHM TAPED S. CHIP RES. 0-OHM TAPED S. CHIP RES. 0-OHM TAPED S. CHIP RES. 0-OHM TAPED S. CHIP RES. 0-OHM TAPED S. CHIP RES. 0-OHM TAPED S. CHIP RES. 0-OHM TAPED S. CHIP RES. 0-OHM TAPED S. CHIP RES. 0-OHM TAPED S. CHIP RES. 0-OHM TAPED S. CHIP RES. 0-OHM TAPED S. CHIP RES. 0-OHM TAPED S. CHIP RES. 0-OHM TAPED S. CHIP RES. 0-OHM TAPED S. CHIP RES. 0-OHM TAPED S. CHIP RES. 0-OHM TAPED S. CHIP RES. 0-OHM TAPED S. CHIP RES. 0-OHM TAPED S. CHIP RES. 0-OHM TAPED S. CHIP RES. 0-OHM TAPED S. CHIP RES. 0-OHM TAPED S. CHIP RES. 0-OHM TAPED S. CHIP RES. 0-OHM TAPED S. CHIP RES. 0-OHM TAPED S. CHIP RES. 0-OHM TAPED S. CHIP RES. 0-OHM TAPED S. CHIP RES. 0-OHM TAPED S. CHIP RES. 0-OHM TAPED S. CHIP RES. 0-OHM TAPED S. CHIP RES. 0-OHM TAPED S. CHIP RES. 0-OHM TAPED
* SN CODE EX CODE
S S S S S S S S S S S S S S S S S S S S S S S S S S S S S S S S S S S S S S S S AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA
!
RES 1,5KOHM 5% 1/8W S RES 180KOHM 5% 1/2W S RES 8,2KOHM 5% 1/8W S RES 18KOHM 5% 1/4W S RES 120KOHM 5% 1/2W S RES 180 OHM 5% 1/2W S RES 180 OHM 5% 1/2W S S. CHIP RES. 33K-OHM TAPED S S CHIP RES. 15K-OHM TAPED S S. CHIP RES. 3.3K-OHM TAPED S S. CHIP RES. 100-OHM TAPED S S. CHIP RES. 100-OHM TAPED S S. CHIP RES. 100-OHM TAPED S S. CHIP RES. 100-OHM TAPED S S.CHOP REG 22K-OHM T S S. CHIP RES. 100-OHM TAPED S S. CHIP RES. 100-OHM TAPED S S. CHIP RES. 100-OHM TAPED S S. CHIP RES. 100-OHM TAPED S S CHIP RES. 180-OHM TAPED S S. CHIP RES. 220-OHM TAPED S S CHIP RES TAPE 330 OHM S S. CHIP RES. 680-OHM TAPED S S. RES. 4.7K OHM TAPED S S. CHIP RES. 100-OHM TAPED S S. CHIP RES. 0-OHM TAPED S S. CHIP RES. 0-OHM TAPED S RES 100 OHM 5% 1/8W S RES 100 OHM 5% 1/8W S RES 3,3KOHM 5% 1/8W S RES 100 OHM 5% 1/8W S RES 3,3KOHM 5% 1/8W S S. CHIP RES. 100-OHM TAPED S S CHIP RES. 15K-OHM TAPED S S. CHIP RES. 100-OHM TAPED S RES 15KOHM 5% 1/8W S S. CHIP RES. 100-OHM TAPED S S. RESISTOR 1.2K OHM S S. CHIP RES. 220K-OHM TAPED S S. CHIP RES. 100-OHM TAPED S RES 100 OHM 5% 1/8W S S. CHIP RES. 100-OHM TAPED S S. CHIP RES. 100-OHM TAPED S RES 3,3KOHM 5% 1/8W S S. CHIP RES. 100-OHM TAPED S RES 3,3KOHM 5% 1/8W S RES 100 OHM 5% 1/8W S S.CHOP REG 22K-OHM T S S. CHIP RES. 1.5K-OHM S S. CHIP RES. 1.5K-OHM S S. CHIP RES. 0-OHM TAPED S S. CHIP RES. 5.6K-OHM TAPED S S. CHIP RES. 0-OHM TAPED S S. CHIP RES. 0-OHM TAPED S SURFACE MOUNT CHIP RESISTORS S. CHIP RES. 0-OHM TAPED S S. CHIP RES. 0-OHM TAPED S S. CHIP RES. 100-OHM TAPED S S.C. RESISTOR 10K OHM S S. RES. 4.7K OHM TAPED S S. CHIP RES. 100-OHM TAPED S RES 100 OHM 5% 1/8W S RES 100 OHM 5% 1/8W S RES 100 OHM 5% 1/8W S RES 100 OHM 5% 1/8W S S.CHIP RES TAPE 1K OHM S S.C. RESISTOR 10K OHM S S. CHIP RES. 33K-OHM TAPED S S.C. RESISTOR 10K OHM S S. CHIP RES. 33K-OHM TAPED S S.C. RESISTOR 10K OHM S S. CHIP RES. 0-OHM TAPED S S. CHIP RES. 0-OHM TAPED S S. CHIP RES. 0-OHM TAPED S
MISCELLANEOUS PARTS
! !
!
F 0701 F 0751 FB 0451 FB 0452 FB 0601 FB 0701 FH 0701 FH 0702 P 0302 P 0601 P 0602 P 0701 P 0702 P 0801 P 1001 RMC1001 S 0701 S 1001 S 1002 S 1003 S 1004 S 1005 SC 0451 VA 0701
QFS-C3229CEZZ QFS-J2521CEZZ RBLN-0037CEZZ RBLN-0037CEZZ RBLN-0037CEZZ RBLN-0037CEZZ QFSHD1001BMZZ QFSHD1002BMZZ QPLGN0441CEZZ QPLGN0441CEZZ QPLGN0505CEZZ QPLGN0304CEZZ QPLGN0207CEZZ QPLGN0541CEZZ QPLGN0641CEZZ RRMCU0255CEZZ QSW-P0591CEZZ QSW-K0079GEZZ QSW-K0079GEZZ QSW-K0079GEZZ QSW-K0079GEZZ QSW-K0079GEZZ QSOCZ2107BMZZ RH-VX0047