Text preview for : Samsung-TV-Service-Manual-CS29A5HT8XBWT.pdf part of SAMSUNG CS29A5HT8XBWT TV d 29"
Back to : Samsung-TV-Service-Manual | Home
COLOR TELEVISION RECEIVER
Chassis : Model : KS3A(P) (REV. 2) CS29A5HT8X/BWT CS29A5HT8X/NWT CS29A5HT8X/VWT CZ21A8VW8X/ELS
RTV servis Horvat
Tel: ++385-31-856-637 Tel/fax: ++385-31-856-139 Mob: 098-788-319
www.rtv-horvat-dj.hr
COLOR TELEVISION RECEIVER
CONTENTS
1. Precautions 2. Reference Information 3. Specifications 4. Alignment and Adjustments 5. Troubleshooting 6. Exploded Views and Parts List 7. Electrical Parts List 8. Block Diagrams 9. Wiring Diagram 10. Schematic Diagrams
www.rtv-horvat-dj.hr
Precautions
1. Precautions
Follow these safety, servicing and ESD precautions to prevent damage and protect against potential hazards such as electrical shock and X-rays.
1-1 Safety Precautions
1. Be sure that all of the built-in protective devices are replaced. Restore any missing protective shields. 2. When reinstalling the chassis and its assemblies, be sure to restore all protective devices, including: nonmetallic control knobs and compartment covers. 3. Make sure that there are no cabinet openings through which people--particularly children--might insert fingers and contact dangerous voltages. Such openings include the spacing between the picture tube and the cabinet mask, excessively wide cabinet ventilation slots, and improperly fitted back covers. If the measured resistance is less than 1.0 megohm or greater than 5.2 megohms, an abnormality exists that must be corrected before the unit is returned to the customer. 4. Leakage Current Hot Check (Figure 1-1): Warning: Do not use an isolation transformer during this test. Use a leakagecurrent tester or a metering system that complies with American National Standards Institute (ANIS C101.1, Leakage Current for Appliances), and Underwriters Laboratories (UL Publication UL1410, 59.7). 5. With the unit completely reassembled, plug the AC line cord directly into the power outlet. With the unit's AC switch first in the ON position and then OFF, measure the current between a known earth ground (metal water pipe, conduit, etc.) and all exposed metal parts, including: antennas, handle brackets, metal cabinets, screwheads and control shafts. The current measured should not exceed 0.5 milliamp. Reverse the powerplug prongs in the AC outlet and repeat the test.
DEVICE UNDER TEST TEST ALL EXPOSED METAL SURFACES 2-WIRE CORD ALSO TEST WITH PLUG REVERSED (USING AC ADAPTER PLUG AS REQUIRED)
LEAKAGE CURRENT TESTER
(READING SHOULD NOT BE ABOVE 0.5mA)
EARTH GROUND
Fig. 1-1 AC Leakage Test 6. Antenna Cold Check: With the unit's AC plug disconnected from the AC source, connect an electrical jumper across the two AC prongs. Connect one lead of the ohmmeter to an AC prong. Connect the other lead to the coaxial connector. 7. X-ray Limits: The picture tube is especially designed to prohibit X-ray emissions. To ensure continued X-ray protection, replace the picture tube only with one that is the same type as the original. Carefully reinstall the picture tube shields and mounting hardware; these also provide X-ray protection. 8. High Voltage Limits: High voltage must be measured each time servicing is done on the B+, horizontal deflection or high voltage circuits. Correct operation of the X-ray protection circuits must be reconfirmed whenever they are serviced. (X-ray protection circuits also may be called "horizontal disable" or "hold-down".) Heed the high voltage limits. These include the Xray Protection Specifications Label, and the Product Safety and X-ray Warning Note on the service data schematic.
Samsung Electronics
www.rtv-horvat-dj.hr
1-1
Precautions
1-1 Safety Precautions (Continued)
9. High voltage is maintained within specified limits by close-tolerance, safety-related components and adjustments. If the high voltage exceeds the specified limits, check each of the special components. 10. Design Alteration Warning: Never alter or add to the mechanical or electrical design of this unit. Example: Do not add auxiliary audio or video connectors. Such alterations might create a safety hazard. Also, any design changes or additions will void the manufacturer's warranty. 11. Hot Chassis Warning: Some TV receiver chassis are electrically connected directly to one conductor of the AC power cord. If an isolation transformer is not used, these units may be safely serviced only if the AC power plug is inserted so that the chassis is connected to the ground side of the AC source. To confirm that the AC power plug is inserted correctly, do the following: Using an AC voltmeter, measure the voltage between the chassis and a known earth ground. If the reading is greater than 1.0V, remove the AC power plug, reverse its polarity and reinsert. Re-measure the voltage between the chassis and ground. 12. Some TV chassis are designed to operate with 85 volts AC between chassis and ground, regardless of the AC plug polarity. These units can be safely serviced only if an isolation transformer inserted between the receiver and the power source. 13. Some TV chassis have a secondary ground system in addition to the main chassis ground. This secondary ground system is not isolated from the AC power line. The two ground systems are electrically separated by insulating material that must not be defeated or altered. 14. Components, parts and wiring that appear to have overheated or that are otherwise damaged should be replaced with parts that meet the original specifications. Always determine the cause of damage or overheating, and correct any potential hazards. 15. Observe the original lead dress, especially near the following areas: Antenna wiring, sharp edges, and especially the AC and high voltage power supplies. Always inspect for pinched, out-of-place, or frayed wiring. Do not change the spacing between components and the printed circuit board. Check the AC power cord for damage. Make sure that leads and components do not touch thermally hot parts. 16. Picture Tube Implosion Warning: The picture tube in this receiver employs "integral implosion" protection. To ensure continued implosion protection, make sure that the replacement picture tube is the same as the original. 17. Do not remove, install or handle the picture tube without first putting on shatterproof goggles equipped with side shields. Never handle the picture tube by its neck. Some "in-line" picture tubes are equipped with a permanently attached deflection yoke; do not try to remove such "permanently attached" yokes from the picture tube. 18. Product Safety Notice: Some electrical and mechanical parts have special safety-related characteristics which might not be obvious from visual inspection. These safety features and the protection they give might be lost if the replacement component differs from the original--even if the replacement is rated for higher voltage, wattage, etc. Components that are critical for safety are indicated in the circuit diagram by shading, ( ) or ( ). Use replacement components that have the same ratings, especially for flame resistance and dielectric strength specifications. A replacement part that does not have the same safety characteristics as the original might create shock, fire or other hazards.
1-2
www.rtv-horvat-dj.hr
Samsung Electronics
Precautions
1-2 Servicing Precautions
Warning1: First read the "Safety Precautions" section of this manual. If some unforeseen circumstance creates a conflict between the servicing and safety precautions, always follow the safety precautions. Warning2: An electrolytic capacitor installed with the wrong polarity might explode. 1. Servicing precautions are printed on the cabinet. Follow them. 2. Always unplug the unit's AC power cord from the AC power source before attempting to: (a) Remove or reinstall any component or assembly, (b) Disconnect an electrical plug or connector, (c) Connect a test component in parallel with an electrolytic capacitor. 3. Some components are raised above the printed circuit board for safety. An insulation tube or tape is sometimes used. The internal wiring is sometimes clamped to prevent contact with thermally hot components. Reinstall all such elements to their original position. 4. After servicing, always check that the screws, components and wiring have been correctly reinstalled. Make sure that the portion around the serviced part has not been damaged. 5. Check the insulation between the blades of the AC plug and accessible conductive parts (examples: metal panels, input terminals and earphone jacks). 6. Insulation Checking Procedure: Disconnect the power cord from the AC source and turn the power switch ON. Connect an insulation resistance meter (500V) to the blades of the AC plug. The insulation resistance between each blade of the AC plug and accessible conductive parts (see above) should be greater than 1 megohm. 7. Never defeat any of the B+ voltage interlocks. Do not apply AC power to the unit (or any of its assemblies) unless all solid-state heat sinks are correctly installed. 8. Always connect a test instrument's ground lead to the instrument chassis ground before connecting the positive lead; always remove the instrument's ground lead last.
Samsung Electronics
www.rtv-horvat-dj.hr
1-3
Precautions
1-3 Precautions for Electrostatically Sensitive Devices (ESDs)
1. Some semiconductor ("solid state") devices are easily damaged by static electricity. Such components are called Electrostatically Sensitive Devices (ESDs); examples include integrated circuits and some field-effect transistors. The following techniques will reduce the occurrence of component damage caused by static electricity. 2. Immediately before handling any semicon ductor components or assemblies, drain the electrostatic charge from your body by touching a known earth ground. Alternatively, wear a discharging wrist-strap device. (Be sure to remove it prior to applying power-- this is an electric shock precaution.) 3. After removing an ESD-equipped assembly, place it on a conductive surface such as aluminum foil to prevent accumulation of electrostatic charge. 4. Do not use freon-propelled chemicals. These can generate electrical charges that damage ESDs. 5. Use only a grounded-tip soldering iron when soldering or unsoldering ESDs. 6. Use only an anti-static solder removal device. Many solder removal devices are not rated as "anti-static"; these can accumulate sufficient electrical charge to damage ESDs. 7. Do not remove a replacement ESD from its protective package until you are ready to install it. Most replacement ESDs are packaged with leads that are electrically shorted together by conductive foam, aluminum foil or other conductive materials. 8. Immediately before removing the protective material from the leads of a replacement ESD, touch the protective material to the chassis or circuit assembly into which the device will be installed. 9. Minimize body motions when handling unpackaged replacement ESDs. Motions such as brushing clothes together, or lifting a foot from a carpeted floor can generate enough static electricity to damage an ESD.
1-4
www.rtv-horvat-dj.hr
Samsung Electronics
Reference Information
2. Reference Information
2-1 Tables of Abbreviations and Acronyms
Table 2-1 Abbreviations A Ah Å dB dBm °C °F °K F G GHz g H Hz h ips kWh kg kHz k km km/h kV kVA kW I MHz Ampere Ampere-hour Angstrom Decibel Decibel Referenced to One Milliwatt Degree Celsius Degree Fahrenheit degree Kelvin Farad Gauss Gigahertz Gram Henry Hertz Hour Inches Per Second Kilowatt-hour Kilogram Kilohertz Kilohm Kilometer Kilometer Per Hour Kilovolt Kilovolt-ampere Kilowatt Liter Megahertz MV MW M m µA µF µH µm µs µW mA mg mH mI mm ms mV nF pF Ib rpm rps s V VA W Wh Megavolt Megawatt Megohm Meter Microampere Microfarad Microhenry Micrometer Microsecond Microwatt Milliampere Milligram Millihenry Milliliter Millimeter Millisecond Millivolt Nanofarad Ohm Picofarad Pound Revolutions Per Minute Revolutions Per Second Second (Time) Volt Volt-ampere Watt Watt-hour
Samsung Electronics
www.rtv-horvat-dj.hr
2-1
Reference Information
Table 2-2 Table of Acronyms ABL AC ACC AF AFC AFT AGC AM ANSI APC APC A/V AVC BAL BPF B-Y CATV CB CCD CCTV Ch CRT CW DC DVM EIA ESD ESD FBP FBT FF FM FS GND G-Y H HF HI-FI IC IC IF Automatic Brightness Limiter Alternating Current Automatic Chroma Control Audio Frequency Automatic Frequency Control Automatic Fine Tuning Automatic Gain Control Amplitude Modulation American National Standards Institute Automatic Phase Control Automatic Picture Control Audio-Video Automatic Volume Control Balance Bandpass Filter Blue-Y Community Antenna Television (Cable TV) Citizens Band Charge Coupled Device Closed Circuit Television Channel Cathode Ray Tube Continuous Wave Direct Current Digital Volt Meter Electronics Industries Association Electrostatic Discharge Electrostatically Sensitive Device Feedback Pulse Flyback Transformer Flip-Flop Frequency Modulation Fail Safe Ground Green-Y High High-Frequency High Fidelity Inductance-Capacitance Integrated Circuit Intermediate Frequency I/O L L LED LF MOSFET MTS NAB NEC NTSC OSD PCB PLL PWM QIF R RC RF R-Y SAP SAW SIF SMPS S/N SW TP TTL TV UHF UL UV VCD VCO VCXO VHF VIF VR VTR VTVM TR Input/output Left Low Light Emitting Diode Low Frequency Metal-Oxide-Semiconductor-Field-Effect-Tr Multi-channel Television Sound National Association of Broadcasters National Electric Code National Television Systems Committee On Screen Display Printed Circuit Board Phase-Locked Loop Pulse Width Modulation Quadrature Intermediate Frequency Right Resistor & Capacitor Radio Frequency Red-Y Second Audio Program Surface Acoustic Wave(Filter) Sound Intermediate Frequency Switching Mode Power Supply Signal/Noise Switch Test Point Transistor Transistor Logic Television Ultra High Frequency Underwriters Laboratories Ultraviolet Variable-Capacitance Diode Voltage Controlled Oscillator Voltage Controlled Crystal Oscillator Very High Frequency Video Intermediate Frequency Variable Resistor Video Tape Recorder Vacuum Tube Voltmeter Transistor
2-2
www.rtv-horvat-dj.hr
Samsung Electronics
Reference Information
2-2 IC Line Up
Table 2 - 3 IC Line - Up NO BOARD LOC. NO IC201S IC601 IC901 IC902 IC602 HIC201 HIC202 HIC203 HIC204 HIC401 IC301 Q402 Q401 D414 IC401 1 MAIN Q404 IC801S D801S PC801S IC802 D805 D806 D807 D802 IC201 IC804 IC803 IC903 IC904 Q909 Q910 TU01S TU02S Samsung Electronics TCLS3101PD09A9(S) TCPN3081PD09A(S) Main Tuner with IF Block Sub Tuner with IF Block Refer to Table 2-3-4 Refer to Table 2-3-5 2-3 FMG-G2CS KA78RM33 KA7806 KA78R08 KA78RM33 KIA7025AP 2N7000 3.3V Regulator 6V Regulator 8V Controlled Regulator 3.3V Regulator MICOM Reset IC IIC Level Shifter VDPY FML-G12S Rectifier Diode HC801 DDRI001 LA7845 KSC2073-H2 KSD5703 FMP-3FU KA393 IRF620 3S1265R RBV606 PC123Y KA78R05 SPS Controllor Bridge Diode Photo Coupler 5V Controlled Regulator E/W Drive IC Horizontal Drive IC HC401 100Hz Horizontal Pulse AMP Vertical IC Option DRGB001 RGB Drive AMP Hybrid IC SPEC VDP3112B MSP3411G SDA555X KS24L161 TDA7297 DESCRIPTION Video Processor Multistandard Sound Processor MICOM, TTX(MTP) EEPROM Audio AMP Refer to Table 2-3-3 VM Option REMARK Refer to Table 2-3-1 Refer to Table 2-3-2
www.rtv-horvat-dj.hr
Reference Information
Table 2 - 3 IC Line - Up NO 1 BOARD MAIN LOC. NO T801S T444S IC501 IC502 2 CRT IC503 QF04 QF05 QG02 QG03 ICG01 3 4 5 DOUBLE FOCUS V-S/W PIP ICP02 ICH01 QH01 ICS01 ICP01 2SC2344 2SA1011 KSA940 KSD2073-H2 KA4558 KA4558 2SC4636RB TEA6425 SDA9489X EZ1086CM OP-AMP (TILT) OP-AMP TR-Power Video Switching IC with Adder Output High-end Picture-In Picture IC 3.3V Regulator Option Option Option Push-Pull (VM) Option TR-Power (TILT) TDA6111Q Video Output AMP R.G.B Drive SPEC AA26-00046A FUJ-29B001 DESCRIPTION Trans Switching Trans FBT REMARK Refer to Table 2-3-6 Refer to Table 2-3-7
2-4
www.rtv-horvat-dj.hr
Samsung Electronics
Reference Information
Table 2-3-1 VIDEO IC (IC201S) SPEC VDP3108B VDP3112B VDP3120B VDP3130Y VDP3140D 50Hz Basic 50Hz, 2H Comb Filtr 50Hz, 2H Comb Filter, Horizontal Scaler 50Hz, 2H Comb Filter, DVD Input 100Hz FUNCTION REMARK
Table 2-3-2 SOUND IC (IC601) SPEC MSP3400D MSP3410D MSP3411G Multistandard, A2 Stereo Multistandard, A2 Stereo, Nicam Multistandard, A2 Stereo, Nicam, Vitual Dolby FUNCTION REMARK
Table 2-3-3 SOUND AMP (IC602) SPEC TDA7297 15W x 2CH, 10W x 2CH FUNCTION REMARK
Table 2-3-4 1'st TUNER (TU01S) SPEC TCLS3101PD09A(S) TCPS3001PD09D(S) TCPS3001PD09E(S) Note CS with LNA Function CS CS India FUNCTION Main REMARK
TCPS3001PD09A(S) is out-of-date, TCPS3001PD09D(S) which is up-to-date has the same function.
Table 2-3-5 2'nd TUNER (TU02S) SPEC TCPS3000PC09B(S) CS FUNCTION Sub REMARK
Samsung Electronics
www.rtv-horvat-dj.hr
2-5
Reference Information
Table 2-3-6 TRANS SPEC FUJ-29B001 FUH-29A001B 29" 21" FUNCTION REMARK
Table 2-3-7 TRANS FLYBACK (FBT) SPEC AA26-00046A AA26-00044C 29" 21" FUNCTION REMARK
2-6
www.rtv-horvat-dj.hr
Samsung Electronics
Specifications
3. Specifications
Television System
CS PAL/SECAM-B/G,D/K,L,I, NTSC-M 75ohms, Coaxial Cable 100W (Applied When 29" Flat) 220V Only Free Voltage Frequency 50/60Hz 15W x 2CH Output 10W x 2CH 5W x 2CH Vitual Dolby Effect Turbo Sound Pseudo Stereo RCA Input Front (AV2) S-VHS Head-Phone
Option Option 29 Inch 21 Inch Not Present R815
Antena Input
Consumption
Power
Requirements
Sound
Jacks
Back
2Scart Input/Output DVD Input(YPbPr) AV2 Monitor Audio Output S-VHS
AV1 : Scart I/O, RGB Input, RF Out AV2 : Scart I/O, Monitor Out
Option Option Option
Specifications are subject to change. Specifications for Model Name (Ex. CS29A6??8X/HAC) Function N P PF PT PW MT NT WT GW NICAM 2 TUNER PIP 2 TUNER PIP, NICAM, TTX 2 TUNER PIP, A2 STEREO, TTX 2 TUNER PIP, A2 STEREO 2 TUNER MULTI PIP, A2 STEREO, NICAM, TTX A2 STEREO, TTX 1 TUNER PIP, A2 STEREO, TTX "NICAM" means that A2 STEREO + NICAM NOTE
Samsung Electronics
www.rtv-horvat-dj.hr
3-1
Alignment and Adjustments
4. Alignment and Adjustments
4-1 General Alignment Instructions
1. Usually, a color TV-VCR needs only slight touch-up adjustment upon installation. Check the basic characteristics such as height, horizontal and vertical sync and focus. 2. Observe the picture for good black and white details. There should be objectionable color shading; if color shading is present, demagnetize, perform purity and convergence adjustments described below. 3. Use the specified test equipment or its equivalent. 4. Correct impedance matching is essential. 8. To protect against shock hazard, use an isolation transformer. 5. Avoid overload. Excessive signal from a sweep generator might overload the front-end of the TV. When inserting signal markers, do not allow the marker generator to distort test results. 6. Connect the TV only to an AC power source with voltage and frequency as specified on the backcover nameplate. 7. Do not attempt to connect or disconnect any wires while the TV is turned on. Make sure that the power cord is disconnected before replacing any parts.
4-2 Automatic Degaussing
A degaussing coil is mounted around the picture tube, so that external degaussing after moving the TV should be unnecessary. But the receiver must be properly degaussed upon installation. The degaussing coil operates for about 1 second after the power is switched ON. If the set is moved or turned in a different direction, the power should be OFF for at least 10 minutes. If the chassis or parts of the cabinet become magnetized, poor color purity will result. If this happens, use an external degaussing coil. Slowly move the degaussing coil around the faceplate of the picture tube and the sides and front of the receiver. Slowly withdraw the coil to a distance of about 6 feet before turning power OFF. If color shading persists, perform the following Color purity and Convergence adjustments.
4-3 High voltage Check
CAUTION : There is no high voltage adjustment on this chassis. The B+ power supply should be +135 volts (with full color- bar input and normal picture level).
1. Connect a digital voltmeter to the second anode of the picture tube. 2. Turn on the TV. Set the Brightness and Contrast controls to minimum (zero beam current). 3. Adjust the Brightness and contrast controls to both extremes. Ensure that the high voltage does not exceed 32 KV under any conditions.
Samsung Electronics
www.rtv-horvat-dj.hr
4-1
Alignment and Adjustments
4-4 Dynamic Focus Adjustment
1. A dynamic focus adjustment should be done after replacing the CRT PCB, FBT or CRT. 2. Input a crosshatch pattern.
3. Enter " STANDARD " in video mode. 4. Turn the Dynamic focus VR fully clockwise (maximum).( ) 5. Turn the Static focus VR fully counterclockwise (maximum).( ) 6. Slowly turn the static focus VR counterclockwise. Adjust until the vertical line in the middle of the screen has maximum clarity.( ) 7. Slowly turn the dynamic focus VR (clockwise) and adjust the 3rd horizontal line for maximum clarity.( ) 8. Repeat 4-7, if necessary.
H
STATIC FOCUS VR
V
DYNAMIC FOCUS VR
SCREEN
4-5 SCREEN Adjustment
1. Input Toshiba Pattern 2. Enter "Service Mode".(Refer to "Service Mode") 3. Select "G2-Adjust". 4. Set the values as below. 29 Inch IBRM = 220 WDRV = 35 CDL = 220 COLR G B = 150 150 150 21 Inch IBRM = 220 WDRV = 35 CDL = 165 COL = 70
4-2
www.rtv-horvat-dj.hr
Samsung Electronics
Alignment and Adjustments
5. Turn the SCREEN VR until "MRCR G B" and "MRWDG" are green and those value are about 100. (The incorrect SCREEN Voltage may result that "MRCR G B" and "MRWDG" should be red)
Note 1. When you do not have Toshiba Pattern, follow this method. 1. 2. 3. 4. 5. Set the TV on the condition that AV mode no signal(black) Enter the "Menu" and set the mode to blue screen off. Enter the "Service Mode". Select " G2-Adjust". Set the values as below. IBRM = 220 WDRV = 35 CDL = 220 COLR G B = 150 150 150 6. Turn the SCREEN VR until the value of " MRCR G B" is about 120. Do not mind that the "OSD" Color is red.
s After completing G2-Adjust, follow this procedure. x Enter the "Video Adjust 1". Choose any item in menu. (ex. Select "Red Cutoff") Change the value of item you select, and recover the value.
For example, when the value of "Red Cutoff" is 127, change the value to 128 and restore the value to 127. If you do not follow this procedure, the picture may be abnormal. For example, when the TV set is on, the picture becames brighter gradually.
Samsung Electronics
www.rtv-horvat-dj.hr
4-3
Alignment and Adjustments
4-6 E2PROM (IC902) Replacement
1. When IC902 is replaced, all adjustment data revert to the initial values. So, all adjustment values when servicing should be readjusted. 2. After IC902 is replaced, connect the AC power supply cord. 3. Turn the power switch ON. 4. In stand-by, warm up the TV for at least 10 seconds. 5. Power on the TV.
4-7 White Balance Adjustment
s Equipment : Color-Analyzer (CA-100) s Input Signal : Pattern signal (Toshiba pattern) 1. Select STANDARD from the menu. 2. Input an 100% White pattern. 3. Enter the "Service Mode". (Refer to "4-8 Service Mode") 4. Warm up the TV set at least for 30 minutes. 5. Input a Toshiba pattern signal. 6. Enter the "Video Adjust1". - Adjust "Sub Contrast" so that Y (luminance) becomes 40 ft ± 3. - Use "Red Drive" and " Blue Drive" to adjust High-Light (x : 290, y : 300) - Adjust "Sub Bright" so that Y (luminance) becomes 1.3ft ± 0.3. - Use "Red Cutoff" and "Blue Cutoff" to adjust Low-Light (x : 290, y : 300). 7. Adjust CA-100 so that the final adjustment value can be fixed. 8. Use the Channel Up/Down (v/w) buttons to move the cursor on the adjustment modes. 9. Use the Volume +/- buttons to change the adjustment value.
4-4
www.rtv-horvat-dj.hr
Samsung Electronics
Alignment and Adjustments
4-8 Factory Adjustment
4-8-1 Service Mode
1. To enter the "Service Mode", Press the remote-control keys in this sequence : - If you do not have Factory remote-control
PICTURE OFF DISPLAY ( ) MENU MUTE PICTURE ON
- If you have Factory remote-control
PICTURE ON DISPLAY ( ) FACTORY
2. After the Service Mode is entered, the initial screen is as shown in the figure below.
Service Deflection Video Adjust 1 Video Adjust 2 Video Adjust 3 Option(81h 0Ch) Reset G2-Adjust Others
*
These hexa * depends on digits are check sum value which the MICOM. If check sum value is changed, the value of 2 E PROM Data newly initialed.
3. Use the Channel Up/Down buttons to move the cursor in the adjustment parameters. Note 2. - When CRT, CRT PCB, FBT, E PROM (sometimes MICOM) is replaced, the adjustment values should be controlled. - After the Service adjustment is completed, Do not select "Reset" in the service mode menu. (After above procedure is done, power is on initially and the "Plug and Play" will be operated.)
2
Samsung Electronics
www.rtv-horvat-dj.hr
4-5
Alignment and Adjustments
4-8-2 Memory Data
4-8-2(A) DEFLECTION (GEOMETRIC ADJUSTMENT VALUE)
Fixed Value No. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 OSD V Shift V Amp V Slope V SC H EW H Trapizium H Parabola H Symmetry H Corner H Shift PIP Contrast PIP Tint PIP PAL V Pos PIP NTSC V Pos PIP H Pos PIP BLKLG Range -128 ~127 -128 ~127 -128 ~127 -128 ~127 -128 ~127 -128 ~127 -128 ~127 -128 ~127 -128 ~127 -128 ~127 0 ~ 15 0 ~ 63 0 ~ 255 0 ~ 255 0 ~ 255 0 ~ 15 Initial Value -30 -7 -3 -17 73 -47 -7 13 23 13 8 0 26 23 30 6 Function Adjust Vertical Picture Position Adjust Vertical Picture Size Adjust Vertical Slope Correction Adjust Vertical S-Correction Adjust Horizontal Picture Size Adjust Horizontal Trapeziod Adjust Horizontal Parabola Wave Adjust Horizontal Symmetry Adjust Horizontal Corner Adjust Horizontal Position Adjust PIP Contrast Adjust PIP Tinit Adjust PIP Vertical Position (Main Picture is PAL) Adjust PIP Vertical Position (Main Picture is NTSC) Adjust PIP Horizontal Position Adjust PIP Green Cutoff Level Not to be adjusted Not to be adjusted Remark
4-6
www.rtv-horvat-dj.hr
Samsung Electronics
Alignment and Adjustments
4-8-2(B) SCREEN CHANGE (I2C BUS GEOMETRIC ADJUSTMENT)
1
V Shift
6
V Amp
2
V Slope
7
V SC
3
H EW
8
H Trapizium
4
H Parabola
9
H Symmetry
5
H Corner
10
H Shift
Samsung Electronics
www.rtv-horvat-dj.hr
4-7
Alignment and Adjustments
4-8-2(C) VIDEO ADJUST 1
Fixed Value No. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 OSD Red Cufoff Green Cutoff Blue Cutoff Red Drive Green Drive Blue Drive Sub Bright Sub Contrast Sub Color Sub Tint BCL Threshold BCL Gain BCL Time TTX Contrast YC Delay Range Initial Value 0 ~255 0 ~255 0 ~255 0 ~255 0 ~255 0 ~255 0 ~ 200 0 ~ 13 0 ~ 27 0 ~ 100 0 ~ 255 0 ~ 15 0 ~ 15 0 ~ 255 0~8 127 127 127 127 127 127 100 50 27 80 65 8 9 90 * Adjust OSD/TTX Contrast Refer to Table 1 Adjust Beam Control Limit Refer to Note 3 Not to be adjusted Adjust Red Cutoff Level Adjust Green Cutoff Level Adjust Blue Cutoff Level Adjust Red Output Gain Adjust Green Output Gain Adjust Blue Output Gain Adjust Brightness Level Adjust Contrast Level Adjust Color Level Adjust Tint Low Light High Light High Light Low Light Function Remark
Note 3. Beam Control Limit Characteristic
beam
MIN 1.8mA 1.6mA BCL GAIN BCL THESHOLD MAX
WDRGB
50
IRE
Table 1. YC Delay Adjustment Table YC Delay Value PAL Def. 4 BG 3 DK 6 I 6 L 7 Def. 1 BG 1 SECAM DK 5 I 8 L 5 NTSC Def. 4 M 3
The "Def." means that TV is in AV mode.
4-8
www.rtv-horvat-dj.hr
Samsung Electronics
Alignment and Adjustments
4-8-2(D) VIDEO 2 ADJUST
Fixed Value No. 1 2 3 4 5 6 7 8 OSD B stretch-BTHR B stretch-BTLT B stretch-BAM Coring RGB Bright RGB Contrast EHT Time EHT Compensation Range 0 ~ 55 0 ~ 15 0 ~ 31 10 ~ 31 0 ~ 255 0 ~ 255 0 ~ 15 0 ~ 255 Initial Value 50 8 4 20 45 15 0 90 Black Stretch Threshold Black Stretch Tilt Position Black Stretch Amount Luma Peaking Filter Coring OSD/TTX RGB Bright OSD/TTX RGB Contrast Electronic High Tension Response Time Electronic High Tension Coefficient Function Remark
Coring : The Value of Center Frequency for the active bandwidth.
4-8-2(E) VIDEO 3 ADJUST
No. 1 2 3 4 5 6 7 OSD Peak Threshold Soft Limit Slope B Hard Limit Peak Video Ref Peak Video Gain Range Initial Value 0 ~ 255 0 ~ 15 0 ~ 255 0~4 0~5 185 4 255 0 0 33 39 Function White Peak Level Threshold Refer to Picture Below White Peak Level Threshold Reference White Peak Level Threshold Gain Auto Color Control Refer to Note Below Remark
ACC-REF(PAL/NTSC) 0 ~ 40 ACCR(SECAM) 0 ~ 39
Note 4. Soft Limit & Hard Limit
Output 511
Part 1
Part 2 0 2
Slope 1 [0...15]
Hard limiter
400
300
200
0 2 4 6 8 10 12 14
4 6 8 10 12 14
Slope 2 [0...15]
Soft Limit Slope B
range=256...511
"Soft Limit" is that Limitting the peak white without feed-back, but "Peak Limit" is that with feed-back for white peak level
100 tilt 1 [0...511] 0 0 100 200 300 400 500 600 700 800 900 tilt 2 [0...511] Li 1023
Samsung Electronics
www.rtv-horvat-dj.hr
4-9
Alignment and Adjustments
4-8-2(E) OPTION
Fixed Value No. 1 2 3 4 5 6 7 8 9 Language Sound CRT AV Mode X-Ray Tilt Control Auto FM PIP Txt Language OSD Initial Value Arab, Iran, Lybya, CIS A2/NICAM, V-Dolby, Mono, L-Stereo 4:3, Wide, Q(12.8:9), 4:3-16:9, Q-16:9 2Scart, 2Scart+S, 1RCA, 2RCA, 2RCA+S, 2RCA+D, 2RCA+S+D, 1Scart Off, On Off, On Off, On 2-Tuner, 1-Tuner, Off Arabic, Farsi, Arab-Hebrew, West Europe, East Europe, Russian, Greek-Turkey Off, On Off, On Off, On Off, On Without "TV/VIDEO" key in the front panel, set to "On" When PIP is "2-Tuner", set to "ON" Function Remark OSD Language Depending on IC601 Refer to Note 5 S:S-VHS, D:DVD
10 11 12 13
LNA Equalizer High Deviate TTX On/Off
14
AV by CH key
Off, On
Initial Value : Refer to Note 6 on the next page.
Note 5. Sound A2/NICAM V-DOLBY Mono L-Stereo MSP3400D, MSP3410D MSP3411G Not used this mode for KS3A Chassis IC601
4-10
www.rtv-horvat-dj.hr
Samsung Electronics
Alignment and Adjustments
Note 6. Option. CS29A5WT8X/UMG Description LANGUAGE SOUND CRT AV MODE X-RAY TILT CONTROL AUTO FM PIP TEXT LANGUAGE LNA EQUALIZER HIGH DEVIATE TTX ON/OFF AV BY CH KEY OPTION BYTE Initial Vaue Arab V-Dolby 4:3 2 RCA + S OFF ON ON OFF Arabic OFF ON ON ON ON 84 CC D8 CS29A6PF8X/HAC Initial Vaue Arab V-Dolby 4:3 2 RCA + S OFF ON ON 2-Tuner Farsi ON ON ON ON OFF 85 DC 5E CS29A6WT8X/BWT Initial Vaue CIS A2/Nicam 4:3 2 SCART + S OFF ON ON OFF RUSSIAN OFF ON ON ON OFF 83 AC 28 CS29A5MT9X/BWT Initial Vaue CIS A2/Nicam 4:3 2 SCART + S OFF ON ON 2-Tuner RUSSIAN ON ON ON ON ON 83 AC AE
4-8-2(F) OTHERS
Fixed Value No. 1 2 3 4 5 6 7 8 OSD VSU H QEW H ZOOM Parabola H 16:9 Parabola TTX H Shift Range 96 ~ 111 -30 ~ 30 -30 ~ 30 -30 ~ 30 -30 ~ 30 Initital Value 98 0 8 -15 6 BG 2 8 Adjust Melody Volumn Adjust Horizontal Parabola in Zoom Mode Adjust Horizontal Parabola in 16:9 Mode Adjust Horizontal OSD/TTX Position Vertical Set Up Time Function Remark
Mono Sound System BG/DK/I/M V Slice Level Melody Volumn 0~3 0 ~ 20
Samsung Electronics
www.rtv-horvat-dj.hr
4-11
Alignment and Adjustments
4-9 MICOM
4-9-1 Pin Layout
Write Protect EEPROM SDA EEPROM SCL Bus-Stop Main SDA Main SCL Sound Reset Video Reset VDD 2.5V GND VDD 3.3V CVBS Input VDD 2.5V GND AFT Scart1 Ident Scart2 Ident Key 1 H-Sync V-Sync Key 3 Key 2 X-Ray Protect IR Input Stand-By LED Time LED
1 2 3 4 5 6 7 8 9 10 11 12 13 14
I/O I/O IO I/O I/O I/O I/O I/O
PWM I/O I/O
52 51 50 49 48 47 46 45
Tilt N.C. Power Sound Mute N.C. N.C. PX. Y PX. Y VDD 3.3V GND VDD 2.5V CORE OSD-B OSD-G OSD-R VDD 2.5V GND X-TAL Out X-TAL In MICOM Reset N.C. N.C. VDD 3.3V GND N.C. Relay
15 ADC 16 ADC 17 ADC 18 ADC 19 20 21 I/O 22 I/O 23 I/O 24 I/O 25 I/O 26 I/O
S D A 5 5 5 X
44 43 42 41 40 39 38 37 36 35 34 33 32 31 30 29 28 I/O 27
4-12
www.rtv-horvat-dj.hr
Samsung Electronics
Alignment and Adjustments
4-9-2 Pin Assignment Specification
PIN NO FUNCTION 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 I/O I/O I/O I/O I/O I/O I/O I/O Vdd GND Vdd CVBS Vdd GND ADC ADC ADC ADC HS VS I/O I/O I/O I/O I/O I/O
ASSIGN Write Protect ROM SDA ROM SCL Bus Stop Main SDA Main SCL Sound Reset Video Reset VDD 2.5V
IN/OUT Out I/O I/O In I/O I/O Out Out
ACTIVE H/L Low
DESCRIPTION EEPROM Write Protection EEPROM Serial Data Line EEPROM Serial Clock Line
Low
Disable Micom IIC Peripheral IC Serial Data Line
Low Low
Peripheral IC Serial Clock Line MSP IC Initial Control VDP IC Initial Control
VDD 3.3V CVBS Input VDD 2.5V In TTX CVBS Input Analog B+ Analog Ground AFT SC1-ID SC2-ID Key1 H-Sync V-Sync Key3 Key2 X-Ray IR-In STD-LED TIM-LED In In In In In In In In In In Out Out Auto Fine Tuning Control Scart1 Ident Scart2 Ident Key1 Input Horizontal Sync Input Vertical Sync Input Key3 Input Key2 Input X-Ray Protection Remocon Signal Input LED Drive Output(Red) LED Drive Output(Green)
Samsung Electronics
www.rtv-horvat-dj.hr
4-13
Alignment and Adjustments
4-9-2 Pin Assignment Specification (Continued)
PIN NO FUNCTION 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 I/O N.C. GND Vdd N.C. N.C. Reset X-In X-Out GND Vdd R G B COR Vdd GND Vdd I/O I/O N.C. Not Used (Programmed Gound Level) N.C. I/O I/O N.C. I/O Tilt Out PWM S-Mute Power Out Out High Low Sound Amp Mute Picture On/Off Control Not Used (Programmed Gound Level) Tilt Control Output VDD 3.3V PX.Y PX.Y In When The Caption Function Adopted, Used. Out VDD 2.5V OSD-R OSD-G OSD-B CORE VDD 2.5V Out Out Out Out Reset X-TAL In X-TAL Out In In Out Low 6MHz 6MHz VDD 3.3V ASSIGN Relay
IN/OUT Out
ACTIVE H/L Low
DESCRIPTION Activate Degausssing Coil Not Used (Programmed Gound Level) Analog Ground Not Used (Programmed Gound Level) Not Used (Programmed Gound Level) Micom Hardware Reset Crystal Oscillation Input Crystal Oscillation Output Analog Ground Analog B+ OSD/TTX Output (Red) OSD/TTX Output (Green) OSD/TTX Output (Blue) Fast Blank/Half Contrast Output
4-14
www.rtv-horvat-dj.hr
Samsung Electronics
Samsung Electronics
Abnormal Check MICOM IIC #5, #6
5-1 No Power
5. Troubleshooting
Plug in Power Cord
ON
Check LED lamp
OFF
Normal
Check IC901 MICOM Input Voltage Abnormal
Normal Check and Replace the MICOM
www.rtv-horvat-dj.hr
5-1
Check Level Shifter Q909, Q910 Output(If 2N7000 Output has the DC Component over 0.7V, it is broken) Normal Check MICOM IIC #2, #3 Normal Check IC902 EEPROM Normal Check IC201S Replace EEPROM(IC902) Abnormal Abnormal
Normal
Check the MICOM Power #59 With Remote Controller
Abnormal
Check IC903 3.3V Regulator Input Voltage Abnormal Check D801 and D811 Normal
Normal
Check and Replace IC903
Normal Replace Q908 Normal Check IC802, IC803 Normal Check IC201S VDP H-OUT #50 Normal Check Q401 H-TR Normal Check 135V Line Normal Replace FBT Abnormal Check PC801S, IC801S Abnormal Replace Q401 Abnormal Replace IC201S Abnormal Replace IC802, IC803 Abnormal Replace Q908
Replace the MICOM
Replace Q909, Q910
Abnormal
Replace D801 or D811
Check IC804 Input Voltage Abnormal Check R828 and D805 Abnormal Check IC801S and FP801S
Normal
Check and Replace IC804
Normal
Check and Replace R828 or D805
Troubleshooting
Note : When you check whether any component is normal, you must let the output pin be open in order not to be affected by the side of output.
No Picture, but sound is in normal operation
Normal
Turn the VR of FBT, higher screen voltage and Check the Deflection is in Normal Operation (If the deflection is in operation, flyback signal is appeared)
Abnormal
Normal
Check CRT PCB RK, BK, GK
Abnormal
Normal
Check IC201S #31
Abnormal
Check Heater Voltage Normal Check CRT and FBT
Abnormal
Check HIC202, HIC203, HIC204 Output
Abnormal
Check 8V Abnormal Normal
Abnormal
Check DZ202 Normal
Abnormal
Check CRT and FBT Normal
Check IC201S #63 or #59 Normal Replace IC201S
Check IC803 Check IC301 Replace IC201S
Replace DZ202
Check 200V, 16.5V Line
Check Tuner CVBS Output
5-2 No Picture
Troubleshooting
5-2
Samsung Electronics
www.rtv-horvat-dj.hr
Troubleshooting
5-3 No Sound
No Sound, but Picture is in normal operation
Normal
Check the CN602 Connection and Signal
Abnormal
Check the Speaker Wire Connection
Normal
Check 14V Line
Abnormal
Check IC602 #7 (If the pin is in low state, Sound is mute) Normal
Abnormal
Check FA803S
Check D816, Q906 Check IC601 #24, #25 Normal Replace IC602 Check IC601 Input Voltages (5V,8V) Normal Check the coils around IC601 Check IC601 Input Signal Normal Replace IC601 Check the Tuner Abnormal Abnormal Abnormal
Samsung Electronics
www.rtv-horvat-dj.hr
5-3
Exploded View & Parts List
6. Exploded View & Parts List
6-1 CS29A5HT8X/BWT
No 1
Code No AA91-00113W AA64-31106S
Description;Specification ASSY CABINET FRONT;-,29A5 KS3A CIS,S704+ CABINET FRONT;29A5 KS3A,S704P+G802P PLAN BADGE-BRAND;AL,SS,SILVER,L65,R2000,-,WINDOW-REMOCON;-,725A,-,PC,-,VIOLET,KNOB-MASTER;-,295A,VT803M MASTER,ABS,HB, SPRING-CS;-,SUS304,0.4,OD5.5,H9,N4,-,-,ASSY-PCB,A/V SIDE;-,29A6,29A5,100HZ,KS3A SCREW-TAPPING;TH,+,2,M4,L15,ZPC(BLK),SWR KNOB-CONTROL;-,725A,-,ABS,HB,GRAY INDICATOR-LED;-,295A,-,ACRYL,-,CLR,SCREW-TAPPING;RH,+,2,M4,L15,ZPC(BLK),SWR
Q'ty 1 1 1 1 1 1 1 2 1 1 3
Remark
www.rtv-horvat-dj.hr
Samsung Electronics
1-1 1-2 1-3 1-4 1-5 1-6 1-7 1-8 1-9
AA64-70117B AA64-40455A AA64-10709A AA61-60005D AA95-00872A 6002-000522 AA64-10710A AA64-40456B 6002-000514
2 2-1 2-2
AA03-00076A AA60-10050V 3704-001032
CRT-COLOR;-,A68QCP891X004(C),+380MG,29IN SCREW-ASSY;WC,HH,+,M6,L30,SWRCH18A,ZPC(S SOCKET-CRT;8P,29PI,35.5PI,AU30U
1 4 1
3 3-1
AA91-00333B AA60-10050A
ASSY HOLDER SPK;-,PP,8ohm/15W,BLK,AA91-0 SCREW-ASSY;WP,RH,+,M4,L25,SWRCH18A,-,ZPC
1 4
4 4-1 4-2
AA64-31107C AA60-10050T AA63-30213C
CABINET-BACK;-,29A5,-,HIPS,V2,BLK,-,SCREW-TAPPING;RH,+,2S,M4,L20,ZPC(BLK),SW COVER-TOP,SPK;-,725A,-,HIPS,V2,BLK,-,-
1 7 1
6-1
Electrical Parts List
7. Electrical Parts List
7-1 CS29A5HT8X/BWT
Level Loc. No. Code No. Description ; Specification Remark Level Loc. No. Code No. Description ; Specification Remark
ASSY PCB MAIN(OPT)
1 ..2 ..2 ..2 ..2 ..2 ..2 ..2 ..2 ..2 ..2 ..2 ..2 ...3 ...3 ...3 ...3 ...3 ..2 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ..2 ...3 ...3 ...3 ...3 ...3 ...3 ..2 ..2 ..2 ...3 ...3 ...3 ...3 ..2 ...3 ...3 ...3 ...3 ..2 ...3 ...3 ...3 ...3 ...3 ..2 ...3 ...3 ...3 ...3 ..2 ..2 ..2 ..2 ..2 ..2 * BOT1 C-BLOC C423 C820 CLAMP CLAMP CLAMP CLAMP CLAMP D-COIL D211 D801S AA94-02759K ASSY PCB MAIN(OPT);CS29A5HT8X/BWT,KS3A,R AA39-00046E AA26-00069A 2301-001296 2401-003076 AA65-30109A AA65-30018A AA65-30105C AA65-30104C AA65-30105A AA27-00128A 0401-000005 AA96-00276A 6003-000335 AA62-00052A AA60-30003A 0402-000549 0205-000129 AA96-00291B 6003-000334 AA62-30177A AA62-00051B AA60-30001A AA02-00007A 6003-000333 0502-001175 0402-001296 0205-000129 AA96-00475A AA62-00066B 6003-000334 1203-001006 0402-001230 0402-000233 0205-000129 AA13-00094A 1204-001727 AA96-50381A 0205-000129 1204-000517 6003-000333 AA62-30180B AA96-50369B 0205-000129 1201-001064 6003-000333 AA62-30181F AA96-50371C AA62-30181H AA61-10386A 6003-000333 1203-001482 0205-000129 AA96-00243C 0205-000129 1203-000284 6003-000335 AA62-00045A AA09-00041A 3722-000195 AA27-10004F AA27-00015A AA27-00031A 0505-001116 LEAD CONNECTOR-ASSY;-,-,-,-,-,-,-,-,-,JU TRANS FBT;FUJ-29C002C(S),DREAM3,4,-,-,-, C-FILM,MPPF;720NF,5%,400V,BK,26X15.5X20M C-AL;3300uF,20%,50V,WP,BK,18x35.5mm CLAMP-FBT;NYLON-66,V2,BLK,-,-,CLAMP-WIRE;NYLON-66,-,-,DATL-600,DONG-A, CLAMP-WIRE;ALL MODEL,NYLON 66,V2,NTR,5MM CLAMP-WIRE;NYLON 66,V2,NTR,W1 Z4,ALL MOD CLAMP-WIRE;NYLON 66,V2,NTR,15MM,ALL MODE COIL DEGAUSSING;-,-,-,-,50T,7,-,29inch,2 DIODE-SWITCHING;1N4148,100V,200mA,DO-35, ASSY H/S;-,BRIDGE,AA62-00052A,RBV606,WA SCREW-TAPTITE;RH,+,2S,M3,L8,ZPC(YEL),SWR HEAT SINK-PS;-,-,-,SILVER,HOLE 18.5mm, 2 WASHER;-,-,-,T1.5,-,SBHG-1,DIODE-BRIDGE;RBV606,600V,6A,-,BK GREASE-SILICON;SC102,JAPAN ASSY H/S;-,POWER,AA62-00051B,2SC5446 + SCREW-TAPTITE;RH,+,2S,M3,L6,ZPC(YEL),SWR HEAT-SINK,PN;-,CUS-1,T1.0,-,KCV12D,-,-,1 HEAT SINK-PS;-,-,-,SILVER,HOLE 34mm,ALL, WASHER-PLATE;M3,ID3.5,15X8.5,T1.0,-,SBHG MICA;DPM-04,MICA,22x29x0.15mm SCREW-TAPTITE;RH,+,2S,M3,L10,ZPC(YEL),SW TR-POWER;2SC5446,NPN,200000mW,TO-3PL,BK DIODE-RECTIFIER;FMP-3FU,1.5KV,5A,TO-3PF, GREASE-SILICON;SC102,JAPAN ASSY H/S;-,REGULATOR,AA62-00066B,FML-G1 HEAT SINK;D2,D3,AL ,T1.0,89,70,-,AA62-00 SCREW-TAPTITE;RH,+,2S,M3,L6,ZPC(YEL),SWR IC-VOLTAGE REGULATOR;78R05,TO-220F,4P,-, DIODE-RECTIFIER;FMG-G2CS,1000V,3A,TO-220 DIODE-RECTIFIER;FML-G12S,200V,5A,-,GREASE-SILICON;SC102,JAPAN IC HYBRID;-,DDRI001A,SIP,5P,-,TP IC-VIDEO PROCESS;VDP3140D-E5,DIP,64P,-,P ASSY-H/S;-,-,AA62-30180B,LA7845,GREASE-SILICON;SC102,JAPAN IC-VERTIVAL DEF.;LA7845,SIP,7P,-,PLASTIC SCREW-TAPTITE;RH,+,2S,M3,L10,ZPC(YEL),SW HEAT SINK-ES;-,A6063 EXTR.,2,WHT,70MM,-, ASSY-H/S;-,-,AA62-30181F,TDA7297,GREASE-SILICON;SC102,JAPAN IC-POWER AMP;7297,ZIP,15P,-,DUAL,32DB,PL SCREW-TAPTITE;RH,+,2S,M3,L10,ZPC(YEL),SW HEAT SINK-ES;-,AL6063 EXTR.,2,WHT,50MM,ASSY-H/S;-,-,AA62-30181H,KA3S1265R,HEAT SINK-ES;-,AL6063 EXTR.,2,WHT,50MM,BRACKET-IC;-,-,SECC 100,T1.0,-,KA2S0680, SCREW-TAPTITE;RH,+,2S,M3,L10,ZPC(YEL),SW IC-PWM CONTROLLER;3S1265R,TO-3P,5P,210,P GREASE-SILICON;SC102,JAPAN ASSY H/S;-,REGULATOR,AA62-00045A,KA7806 GREASE-SILICON;SC102,JAPAN IC-POSI.FIXED REG.;7806,TO-220,3P,-,PLAS SCREW-TAPTITE;RH,+,2S,M3,L8,ZPC(YEL),SWR HEAT SINK-PS;-,-,T1.0,-,-,DREAM,-,-,-,-, IC-MCU;SDA555X-OTP,SDA555X-OTP,-,-,52 JACK-SCART;42P,-,SN,BLK,NO COIL-CHOKE;-,56uH,K,-,2.5A,BK,-,DR12x15, COIL-LINEARLITY;-,7.3UH,L81 DR15X18,-,-, COIL-HORIZ.WIDTH;-,140UH,AR 8X20,0.8MM,B FET-SILICON;BUZ73A,N,200V,22A,0.6ohm,40W
! ..2
Q404
! ! !
S.N.A S.N.A S.N.A S.N.A S.N.A
!
!
S.N.A S.N.A S.N.A
HC401
S.N.A S.N.A S.N.A
S.N.A S.N.A
HC801
S.N.A
! ! !
HIC401 IC201S IC301
S.N.A
S.N.A S.N.A
!
IC602
S.N.A S.N.A S.N.A
! ! ! ! ! ! ! ! !
!
IC801S
S.N.A S.N.A
!
IC804
S.N.A
!
!
IC901 JA701 L402 L403 L408 Q402
! ! ! ! !
...3 ...3 ...3 ..2 ..2 ..2 ..2 ..2 ..2 ..2 ...3 ...3 ...3 ...3 ...3 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ...3 ..2 ..2 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3 ...3
S-H/S T444S T801S TUBE Z
CNS01 CNS02 ICS01 PCB CS01 CS02 CS03 CS04 CS05 CS06 CS07 CS08 DZS01 DZS02 LS01 QS01 QS02 QS03 RS01 RS02 RS03 RS04 RS05 RS06 RS07 RS10 RS11 RS12 RS13
C405 C406 C407 C426 C803 C815 CN501 CN902 CX801S CX802S CY802S FP801S IC202 IC401 IC601 IC803 IC902 L405 L808 LX801S LX802S NT802S PC801S PT801S
AA96-00437A 0505-000156 AA62-00076A 6003-000334 AA65-30105A AA26-00082A AA26-00046A AA39-00108A AA65-30105A AA39-20010C AA95-00871A 3711-002704 3711-002706 1001-001114 AA41-00153E AA99-20082H 2305-000412 2305-000412 2305-000412 2305-000412 2305-000412 2305-000412 2401-002009 2305-000665 0403-000508 0403-000508 2701-000114 0501-000389 0501-000389 0501-000389 2001-000281 2001-000734 2001-000429 2001-000734 2001-000429 2001-000734 2001-000429 2001-000429 2001-000429 2001-000969 2001-000969 0202-000187 AA61-00462B AA99-30192G 2303-001015 2303-001015 2301-001338 2306-000195 2401-003576 2401-003026 3711-002641 3711-003043 2306-000318 2306-000318 2201-002002 3601-000297 1203-001944 1202-000103 1204-001661 1203-001697 1103-001171 AA27-00096A AA27-00098A AA29-30002N AA29-30002N 1404-001045 0604-001038 1404-000002
ASSY H/S;-,MAIN,AA62-00076A,IRF620,100H FET-SILICON;IRF620,N,200V,5A,0.8ohm,50W, HEAT SINK;100Hz,AL ,T1.0,10,40,-,-,SCREW-TAPTITE;RH,+,2S,M3,L6,ZPC(YEL),SWR CLAMP-WIRE;NYLON 66,V2,NTR,15MM,ALL MODE TRANS FBT;FUJ-29C002F(S),CT29A7DR,1.95mH TRANS SWITCHING;-,-,-,AC90~260V,DC135/16 LEAD CONNECTOR-ASSY;,-,-,-,-,-,-,GRT-TUB CLAMP-WIRE;NYLON 66,V2,NTR,15MM,ALL MODE LEAD CONNECTOR-ASSY;-,YFH800-01,S,1P,600 ASSY-PCB,VIDEO S/W;-,100HZ,KS3A,PAL,-,CONNECTOR-HEADER;NOWALL,6P,1R,2.5mm,ANGL CONNECTOR-HEADER;NOWALL,8P,1R,2.5mm,ANGL IC-VIDEO SWITCH;TEA6425,VIDEO SWITCH ,DI PCB-VIDEO SWITCH;CS29A6,FR-1,1L,E,1.6T,2 ASSY-PCB SUB,AUTO; AA95-00871A ,V C-FILM,MPEF;470nF,5%,63V,TP,-,5mm C-FILM,MPEF;470nF,5%,63V,TP,-,5mm C-FILM,MPEF;470nF,5%,63V,TP,-,5mm C-FILM,MPEF;470nF,5%,63V,TP,-,5mm C-FILM,MPEF;470nF,5%,63V,TP,-,5mm C-FILM,MPEF;470nF,5%,63V,TP,-,5mm C-AL;100uF,20%,16V,GP,TP,6.3x7,5 C-FILM,MPEF;100nF,5%,63V,TP,7.5x4.0x5.0m DIODE-ZENER;MTZJ5.6B,5.6V,5.45-5.73V,500 DIODE-ZENER;MTZJ5.6B,5.6V,5.45-5.73V,500 INDUCTOR-AXIAL;10uH,10%,2.5x3.4mm TR-SMALL SIGNAL;KSC815,NPN,400mW,TO-92,T TR-SMALL SIGNAL;KSC815,NPN,400mW,TO-92,T TR-SMALL SIGNAL;KSC815,NPN,400mW,TO-92,T R-CARBON;100OHM,5%,1/8W,AA,TP,1.8X3.2MM R-CARBON;4.7KOHM,5%,1/8W,AA,TP,1.8X3.2M R-CARBON;1KOHM,5%,1/8W,AA,TP,1.8X3.2MM R-CARBON;4.7KOHM,5%,1/8W,AA,TP,1.8X3.2M R-CARBON;1KOHM,5%,1/8W,AA,TP,1.8X3.2MM R-CARBON;4.7KOHM,5%,1/8W,AA,TP,1.8X3.2M R-CARBON;1KOHM,5%,1/8W,AA,TP,1.8X3.2MM R-CARBON;1KOHM,5%,1/8W,AA,TP,1.8X3.2MM R-CARBON;1KOHM,5%,1/8W,AA,TP,1.8X3.2MM R-CARBON;75OHM,5%,1/8W,AA,TP,1.8X3.2MM R-CARBON;75OHM,5%,1/8W,AA,TP,1.8X3.2MM SOLDER-WIRE FLUX;-,RS60S,D1.2,63Sn/37Pb SUPPORT-HEAT SINK;21A9,ABS,GRAY,VO,-,-,ASSY-PCB ROBOT; AA94-02759K ,ER C-FILM,PPF;5.5nF,5%,1.6kV,TP,29x9.5x17,2 C-FILM,PPF;5.5nF,5%,1.6kV,TP,29x9.5x17,2 C-FILM,MPE-PPF;0.68nF,5%,1.6kV,TP,28x7x1 C-FILM,MPPF;360nF,5%,400V,TP,26x19x11.5, C-AL;470uF,20%,450V,GP,ST,35x45mm,1 C-AL;330uF,20%,200V,GP,ST,22x35,10 CONNECTOR-HEADER;BOX,10P,1R,2.54mm,STRAI CONNECTOR-HEADER;BOX,4P,1R,2.5mm,STRAIGH C-FILM,MPPF;220nF,20%,250V,TP,-,22.5mm C-FILM,MPPF;220nF,20%,250V,TP,-,22.5mm C-CERAMIC,DISC;4.7nF,20%,400V,Y5U,TP,16x FUSE-CARTRIDGE;250V,5A,TIME-LAG,GLASS,5. IC-POSI.FIXED REG.;78RM33,TO-220,3P,-,PL IC-VOLTAGE COMP.;393,DIP,8P,300MIL,DUAL, IC-SOUND PROCESSOR;MSP3411G-A2,DIP,52P,IC-VOLTAGE REGULATOR;78R08,TO-220,4P,-,P IC-EEPROM;L51DC,16KBit,DIP,8P,300MIL,10m COIL HORIZ. WIDTH;-,10.0mH,DR15 X 27.5,U COIL CHOKE;-,-,24uH,10%,-,0.1,3.0A,DR10X FILTER-LINE NOISE;-,16MH,1.5A,AC100~260V FILTER-LINE NOISE;-,16MH,1.5A,AC100~260V THERMISTOR-NTC;4.7OHM,15%,2900K,35.0MW,T PHOTO-COUPLER;TR,130-260%,200mW,DIP-4,ST THERMISTOR-PTC;9ohm,20%,-,-,TR,RECT,-
S.N.A S.N.A
S.N.A
S.N.A S.N.A
S.N.A S.N.A S.N.A
Samsung Electronics
www.rtv-horvat-dj.hr
7-1
Electrical Parts List
Level Loc. No. Code No.
Description ; Specification
Remark
Level Loc. No. Code No.
Description ; Specification
Remark
! ...3 ! ...3 ! ...3
...3 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4
RL801S 3501-001040 T401 AA26-50001S TU01S AA40-00060A AA99-10187U C103 2301-000383 C104 2401-003578 C105 2301-000383 C106 2401-000611 C113 2202-000127 C115 2202-000121 C116 2202-000121 C201 2401-000603 C202 2401-002235 C205 2401-002235 C206 2305-000665 C207 2401-002235 C208 2401-001026 C209 2401-001914 C211 2202-000796 C212 2301-000224 C213 2301-000247 C214 2305-000665 C215 2401-002235 C216 2305-000665 C217 2401-001026 C218 2202-000632 C219 2202-000632 C220 2202-000632 C221 2202-000632 C222 2202-000632 C223 2202-000632 C224 2201-002031 C225 2201-002031 C228 2301-000356 C229 2401-002619 C230 2301-000356 C231 2401-002235 C232 2202-000632 C233 2305-000412 C234 2305-000412 C235 2305-000412 C236 2305-000412 C237 2401-000914 C239 2401-002235 C240 2305-000665 C242 2301-000192 C244 2202-000121 C245 2202-000121 C246 2202-000210 C247 2202-000849 C248 2202-000210 C249 2202-000231 C250 2202-000121 C302 2401-000360 C303 2201-002103 C304 2305-000285 C305 2305-000149 C306 2301-000342 C307 2401-000360 C308 2305-000412 C401 2201-000556 C402 2401-001397 C403 2201-000556 C404 2401-001397 C408 2305-000382 C409 2301-001268 C411 2301-000232 C412 2301-000148 C413 2401-000493 C414 2401-002597 C415 2301-000342 C416 2301-000383 C418 2401-002597 C421 2201-000556 C422 2401-001527 C424 2201-000132
RELAY-POWER;12VDC,500mW,10A,1FormA,15mS, TRANS-HORIZ.DRIVE;-,6.0mH,44uH,1.5uH,EI2 TUNER-F/S;TCPS3001PD09D(S),-,PAL-M(NTSC) ASSY-PCB MAIN,AUTO; AA99-30192G ,V C-FILM,PEF;10nF,5%,50V,TP,6x7x3.2mm,5mm C-AL;1000uF,20%,10V,GP,TP,8x20mm,5 C-FILM,PEF;10nF,5%,50V,TP,6x7x3.2mm,5mm C-AL;1uF,20%,50V,WT,TP,5x11,5 C-CERAMIC,MLC-AXIAL;10nF,+80-20%,25V,Y5V C-CERAMIC,MLC-AXIAL;100pF,10%,50V,Y5P,TP C-CERAMIC,MLC-AXIAL;100pF,10%,50V,Y5P,TP C-AL;1uF,20%,50V,GP,TP,5x11,5 C-AL;10uF,20%,16V,GP,TP,5x11mm,5mm C-AL;10uF,20%,16V,GP,TP,5x11mm,5mm C-FILM,MPEF;100nF,5%,63V,TP,7.5x4.0x5.0m C-AL;10uF,20%,16V,GP,TP,5x11mm,5mm C-AL;3.3UF,20%,50V,GP,TP,5X11,5 C-AL;1uF,20%,50V,BP,TP,5x11,5 C-CERAMIC,MLC-AXIAL;1NF,10%,50V,Y5P,TP,3 C-FILM,PEF;22nF,5%,50V,TP,7.4x3.9x13mm,5 C-FILM,PEF;33nF,5%,50V,TP,8.1x4.5x13mm,5 C-FILM,MPEF;100nF,5%,63V,TP,7.5x4.0x5.0m C-AL;10uF,20%,16V,GP,TP,5x11mm,5mm C-FILM,MPEF;100nF,5%,63V,TP,7.5x4.0x5.0m C-AL;3.3UF,20%,50V,GP,TP,5X11,5 C-CERAMIC,MLC-AXIAL;100nF,20%,50V,Z5U,TP C-CERAMIC,MLC-AXIAL;100nF,20%,50V,Z5U,TP C-CERAMIC,MLC-AXIAL;100nF,20%,50V,Z5U,TP C-CERAMIC,MLC-AXIAL;100nF,20%,50V,Z5U,TP C-CERAMIC,MLC-AXIAL;100nF,20%,50V,Z5U,TP C-CERAMIC,MLC-AXIAL;100nF,20%,50V,Z5U,TP C-CERAMIC,DISC;0.005nF,0.5pF,50V,NP0,TP, C-CERAMIC,DISC;0.005nF,0.5pF,50V,NP0,TP, C-FILM,PEF;47nF,5%,50V,TP,7.5x4.0x6.5,5m C-AL;47uF,20%,25V,GP,TP,5x11,5 C-FILM,PEF;47nF,5%,50V,TP,7.5x4.0x6.5,5m C-AL;10uF,20%,16V,GP,TP,5x11mm,5mm C-CERAMIC,MLC-AXIAL;100nF,20%,50V,Z5U,TP C-FILM,MPEF;470nF,5%,63V,TP,-,5mm C-FILM,MPEF;470nF,5%,63V,TP,-,5mm C-FILM,MPEF;470nF,5%,63V,TP,-,5mm C-FILM,MPEF;470nF,5%,63V,TP,-,5mm C-AL;22uF,20%,16V,GP,TP,5x11,5 C-AL;10uF,20%,16V,GP,TP,5x11mm,5mm C-FILM,MPEF;100nF,5%,63V,TP,7.5x4.0x5.0m C-FILM,PEF;1nF,5%,50V,TP,5.3x10mm,5mm C-CERAMIC,MLC-AXIAL;100pF,10%,50V,Y5P,TP C-CERAMIC,MLC-AXIAL;100pF,10%,50V,Y5P,TP C-CERAMIC,MLC-AXIAL;270PF,10%,50V,Y5P,TP C-CERAMIC,MLC-AXIAL;18pF,5%,50V,CH,TP,3. C-CERAMIC,MLC-AXIAL;270PF,10%,50V,Y5P,TP C-CERAMIC,MLC-AXIAL;330pF,10%,50V,Y5P,TP C-CERAMIC,MLC-AXIAL;100pF,10%,50V,Y5P,TP C-AL;100uF,20%,50V,GP,TP,8x11.5,5 C-CERAMIC,DISC;0.015nF,5%,500V,NP0,TP,6. C-FILM,MPEF;220NF,5%,100V,TP,10.5X5.5X15 C-FILM,MPEF;100nF,5%,100V,TP,12x12.5x6.5 C-FILM,PEF;2.2nF,5%,50V,TP,7.4x3.9x13mm, C-AL;100uF,20%,50V,GP,TP,8x11.5,5 C-FILM,MPEF;470nF,5%,63V,TP,-,5mm C-CERAMIC,DISC;0.47nF,10%,500V,Y5P,TP,5. C-AL;470uF,20%,25V,GP,TP,10x16,5 C-CERAMIC,DISC;0.47nF,10%,500V,Y5P,TP,5. C-AL;470uF,20%,25V,GP,TP,10x16,5 C-FILM,MPEF;4.7nF,5%,400V,TP,-,5mm C-FILM,PPF;33nF,5%,630V,TP,20x11x17,7.5 C-FILM,PEF;3.3nF,5%,50V,TP,8.1x4.5x13mm, C-FILM,PEF;10nF,5%,100V,TP,7x3.2x7mm,5mm C-AL;10uF,20%,50V,LZ,TP,5x11mm,5mm C-AL;220uF,20%,35V,GP,TP,10x12.5,5 C-FILM,PEF;2.2nF,5%,50V,TP,7.4x3.9x13mm, C-FILM,PEF;10nF,5%,50V,TP,6x7x3.2mm,5mm C-AL;220uF,20%,35V,GP,TP,10x12.5,5 C-CERAMIC,DISC;0.47nF,10%,500V,Y5P,TP,5. C-AL;47uF,20%,250V,HR,TP,13x25mm,5m C-CERAMIC,DISC;0.1nF,10%,500V,Y5P,TP,6.5
S.N.A
....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4
C425 C601 C603 C604 C605 C607 C608 C610 C611 C612 C613 C617 C620 C621 C622 C623 C624 C625 C626 C627 C628 C629 C630 C631 C632 C634 C635 C636 C637 C638 C639 C640 C641 C642 C643 C644 C645 C646 C647 C649 C652 C654 C656 C657 C701 C702 C703 C707 C708 C804 C805 C807 C808 C809 C810 C811 C814 C816 C817 C818 C819 C821 C822 C823 C824 C825 C826 C827 C829 C831 C832 C833 C835 C837 C838 C839
2301-001259 2201-000558 2401-002235 2401-000603 2305-000665 2202-000796 2202-000796 2301-000445 2301-000445 2401-001914 2401-001914 2401-000493 2305-000665 2401-002458 2401-001989 2202-000231 2202-000231 2401-001989 2401-001989 2202-000231 2401-001989 2202-000231 2401-002235 2401-002235 2202-000806 2401-001840 2305-000665 2401-001026 2401-000027 2202-000231 2202-000231 2401-000027 2401-000027 2202-000231 2401-000027 2202-000231 2401-002235 2305-000665 2202-000286 2301-000108 2401-002235 2201-000611 2201-000304 2201-000304 2202-000121 2202-000231 2202-000231 2401-001989 2401-002235 2201-000332 2201-000332 2301-001397 2401-003046 2301-000356 2301-000356 2301-000356 2201-000406 2401-000293 2201-000599 2401-000722 2201-000599 2301-000192 2201-000599 2401-003046 2401-003046 2305-000665 2401-000287 2401-002212 2305-000665 2305-000665 2401-001840 2401-002619 2401-002289 2305-000665 2401-001840 2305-000665
C-FILM,MPPF;100nF,5%,400V,TP,19x8x16,7.5 C-CERAMIC,DISC;0.47nF,10%,50V,Y5P,TP,5x3 C-AL;10uF,20%,16V,GP,TP,5x11mm,5mm C-AL;1uF,20%,50V,GP,TP,5x11,5 C-FILM,MPEF;100nF,5%,63V,TP,7.5x4.0x5.0m C-CERAMIC,MLC-AXIAL;1NF,10%,50V,Y5P,TP,3 C-CERAMIC,MLC-AXIAL;1NF,10%,50V,Y5P,TP,3 C-FILM,PEF;4.7nF,5%,50V,TP,5.5x7x3mm,5mm C-FILM,PEF;4.7nF,5%,50V,TP,5.5x7x3mm,5mm C-AL;1uF,20%,50V,BP,TP,5x11,5 C-AL;1uF,20%,50V,BP,TP,5x11,5 C-AL;10uF,20%,50V,LZ,TP,5x11mm,5mm C-FILM,MPEF;100nF,5%,63V,TP,7.5x4.0x5.0m C-AL;1000uF,20%,35V,GP,TP,16x25,7.5 C-AL;4.7uF,20%,50V,BP,TP,5x11,5 C-CERAMIC,MLC-AXIAL;330pF,10%,50V,Y5P,TP C-CERAMIC,MLC-AXIAL;330pF,10%,50V,Y5P,TP C-AL;4.7uF,20%,50V,BP,TP,5x11,5 C-AL;4.7uF,20%,50V,BP,TP,5x11,5 C-CERAMIC,MLC-AXIAL;330pF,10%,50V,Y5P,TP C-AL;4.7uF,20%,50V,BP,TP,5x11,5 C-CERAMIC,MLC-AXIAL;330pF,10%,50V,Y5P,TP C-AL;10uF,20%,16V,GP,TP,5x11mm,5mm C-AL;10uF,20%,16V,GP,TP,5x11mm,5mm C-CERAMIC,MLC-AXIAL;220pF,10%,50V,Y5P,TP C-AL;100uF,20%,16V,GP,TP,6.3x11,5 C-FILM,MPEF;100nF,5%,63V,TP,7.5x4.0x5.0m C-AL;3.3UF,20%,50V,GP,TP,5X11,5 C-AL;4.7uF,20%,50V,GP,TP,5x11,5 C-CERAMIC,MLC-AXIAL;330pF,10%,50V,Y5P,TP C-CERAMIC,MLC-AXIAL;330pF,10%,50V,Y5P,TP C-AL;4.7uF,20%,50V,GP,TP,5x11,5 C-AL;4.7uF,20%,50V,GP,TP,5x11,5 C-CERAMIC,MLC-AXIAL;330pF,10%,50V,Y5P,TP C-AL;4.7uF,20%,50V,GP,TP,5x11,5 C-CERAMIC,MLC-AXIAL;330pF,10%,50V,Y5P,TP C-AL;10uF,20%,16V,GP,TP,5x11mm,5mm C-FILM,MPEF;100nF,5%,63V,TP,7.5x4.0x5.0m C-CERAMIC,MLC-AXIAL;56pF,5%,50V,SL,TP,1. C-FILM,PEF;1.5nF,5%,50V,TP,6.5x3.0x5.5mm C-AL;10uF,20%,16V,GP,TP,5x11mm,5mm C-CERAMIC,DISC;0.056nF,5%,50V,NP0,TP,7x3 C-CERAMIC,DISC;0.001nF,0.25pF,50V,NP0,TP C-CERAMIC,DISC;0.001nF,0.25pF,50V,NP0,TP C-CERAMIC,MLC-AXIAL;100pF,10%,50V,Y5P,TP C-CERAMIC,MLC-AXIAL;330pF,10%,50V,Y5P,TP C-CERAMIC,MLC-AXIAL;330pF,10%,50V,Y5P,TP C-AL;4.7uF,20%,50V,BP,TP,5x11,5 C-AL;10uF,20%,16V,GP,TP,5x11mm,5mm C-CERAMIC,DISC;2.2nF,20%,250V,Y5U,TP,9x4 C-CERAMIC,DISC;2.2nF,20%,250V,Y5U,TP,9x4 C-FILM,PPF;2.2nF,5%,1.2kV,TP,15x8.5x13.5 C-AL;47uF,20%,50V,WT,TP,6.3x11,2.5 C-FILM,PEF;47nF,5%,50V,TP,7.5x4.0x6.5,5m C-FILM,PEF;47nF,5%,50V,TP,7.5x4.0x6.5,5m C-FILM,PEF;47nF,5%,50V,TP,7.5x4.0x6.5,5m C-CERAMIC,DISC;0.27nF,10%,2kV,Y5P,TP,6.3 C-AL;100uF,+30-10%,200V,GP,TP,16x25 C-CERAMIC,DISC;0.56nF,10%,500V,Y5P,TP,5. C-AL;2200uF,20%,25V,WT,TP,16x25,7.5 C-CERAMIC,DISC;0.56nF,10%,500V,Y5P,TP,5. C-FILM,PEF;1nF,5%,50V,TP,5.3x10mm,5mm C-CERAMIC,DISC;0.56nF,10%,500V,Y5P,TP,5. C-AL;47uF,20%,50V,WT,TP,6.3x11,2.5 C-AL;47uF,20%,50V,WT,TP,6.3x11,2.5 C-FILM,MPEF;100nF,5%,63V,TP,7.5x4.0x5.0m C-AL;100uF,20%,16V,WT,TP,6.3x11,5 C-AL;10uF,20%,25V,WT,TP,5x11,5 C-FILM,MPEF;100nF,5%,63V,TP,7.5x4.0x5.0m C-FILM,MPEF;100nF,5%,63V,TP,7.5x4.0x5.0m C-AL;100uF,20%,16V,GP,TP,6.3x11,5 C-AL;47uF,20%,25V,GP,TP,5x11,5 C-AL;470uF,20%,35V,WT,TP,10x20,5 C-FILM,MPEF;100nF,5%,63V,TP,7.5x4.0x5.0m C-AL;100uF,20%,16V,GP,TP,6.3x11,5 C-FILM,MPEF;100nF,5%,63V,TP,7.5x4.0x5.0m
7-2
www.rtv-horvat-dj.hr
Samsung Electronics
Electrical Parts List
Level Loc. No. Code No.
Description ; Specification
Remark
Level Loc. No. Code No.
Description ; Specification
Remark
! ! ! ! ! ! !
! ! ! ! ! ! !
....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4
C840 C841 C901 C902 C903 C905 C907 C908 C909 C910 C911 C912 C913 C914 C915 C916 C917 C918 C919 C920 C921 C922 C923 C924 CN502 CN602 CN702 CN704 CN901 CW901 D201 D202 D203 D204 D205 D206 D207 D208 D209 D210 D301 D401 D402 D404 D405 D406 D408 D411 D602 D604 D801 D803 D804 D808 D810 D811 D816 D901 D902 D903 D904 D906 D907 DZ201 DZ202 DZ203 DZ204 DZ205 DZ206 DZ302 DZ303 DZ304 DZ305 DZ306 DZ401 DZ402 DZ601
2401-002212 2401-000611 2202-000632 2301-000192 2202-000719 2202-000796 2305-000412 2202-000863 2301-000383 2201-000980 2201-000980 2401-000027 2401-001840 2305-000665 2401-001840 2305-000665 2401-000493 2401-001840 2202-000632 2401-002235 2202-000632 2202-000632 2202-000796 2202-000632 3711-002646 3711-002644 3711-002647 3711-002646 3711-002644 2503-000156 0401-000005 0401-000005 0404-000156 0404-000156 0404-000156 0404-000156 0401-000005 0401-000005 0401-000005 0401-000005 0402-000546 0402-000540 0402-000534 0402-000534 0401-000005 0402-000132 0401-000005 0402-000534 0401-000005 0401-000005 0402-001111 0402-000546 0401-000005 0402-000132 0402-000132 0402-000132 0402-000546 0404-000156 0404-000156 0404-000156 0404-000156 0401-000005 0402-000132 0403-000508 0403-000508 0403-001321 0403-000508 0403-000508 0403-000508 0403-001329 0403-001329 0403-001329 0403-001221 0403-000700 0403-001325 0401-000005 0403-000508
C-AL;10uF,20%,25V,WT,TP,5x11,5 C-AL;1uF,20%,50V,WT,TP,5x11,5 C-CERAMIC,MLC-AXIAL;100nF,20%,50V,Z5U,TP C-FILM,PEF;1nF,5%,50V,TP,5.3x10mm,5mm C-CERAMIC,MLC-AXIAL;6.8NF,20%,16V,Y5R,3. C-CERAMIC,MLC-AXIAL;1NF,10%,50V,Y5P,TP,3 C-FILM,MPEF;470nF,5%,63V,TP,-,5mm C-CERAMIC,MLC-AXIAL;560pF,10%,50V,Y5P,TP C-FILM,PEF;10nF,5%,50V,TP,6x7x3.2mm,5mm C-CERAMIC,DISC;0.03nF,5%,50V,NP0,TP,5x3, C-CERAMIC,DISC;0.03nF,5%,50V,NP0,TP,5x3, C-AL;4.7uF,20%,50V,GP,TP,5x11,5 C-AL;100uF,20%,16V,GP,TP,6.3x11,5 C-FILM,MPEF;100nF,5%,63V,TP,7.5x4.0x5.0m C-AL;100uF,20%,16V,GP,TP,6.3x11,5 C-FILM,MPEF;100nF,5%,63V,TP,7.5x4.0x5.0m C-AL;10uF,20%,50V,LZ,TP,5x11mm,5mm C-AL;100uF,20%,16V,GP,TP,6.3x11,5 C-CERAMIC,MLC-AXIAL;100nF,20%,50V,Z5U,TP C-AL;10uF,20%,16V,GP,TP,5x11mm,5mm C-CERAMIC,MLC-AXIAL;100nF,20%,50V,Z5U,TP C-CERAMIC,MLC-AXIAL;100nF,20%,50V,Z5U,TP C-CERAMIC,MLC-AXIAL;1NF,10%,50V,Y5P,TP,3 C-CERAMIC,MLC-AXIAL;100nF,20%,50V,Z5U,TP CONNECTOR-HEADER;BOX,7P,1R,2.5mm,STRAIGH CONNECTOR-HEADER;BOX,5P,1R,2.5mm,STRAIGH CONNECTOR-HEADER;BOX,8P,1R,2.5mm,STRAIGH CONNECTOR-HEADER;BOX,7P,1R,2.5mm,STRAIGH CONNECTOR-HEADER;BOX,5P,1R,2.5mm,STRAIGH C-NETWORK;100pFx4,20%,50V DIODE-SWITCHING;1N4148,100V,200mA,DO-35, DIODE-SWITCHING;1N4148,100V,200mA,DO-35, DIODE-SCHOTTKY;RB441Q,10V,100mA,DO-34,TP DIODE-SCHOTTKY;RB441Q,10V,100mA,DO-34,TP DIODE-SCHOTTKY;RB441Q,10V,100mA,DO-34,TP DIODE-SCHOTTKY;RB441Q,10V,100mA,DO-34,TP DIODE-SWITCHING;1N4148,100V,200mA,DO-35, DIODE-SWITCHING;1N4148,100V,200mA,DO-35, DIODE-SWITCHING;1N4148,100V,200mA,DO-35, DIODE-SWITCHING;1N4148,100V,200mA,DO-35, DIODE-RECTIFIER;TVR10G,400V,1.0A,DO-41,T DIODE-RECTIFIER;RU20A,600V,1.5A,-,TP DIODE-RECTIFIER;RG10V,400V,1.2A,DO-201,T DIODE-RECTIFIER;RG10V,400V,1.2A,DO-201,T DIODE-SWITCHING;1N4148,100V,200mA,DO-35, DIODE-RECTIFIER;1N4004,400V,1A,DO-41,TP DIODE-SWITCHING;1N4148,100V,200mA,DO-35, DIODE-RECTIFIER;RG10V,400V,1.2A,DO-201,T DIODE-SWITCHING;1N4148,100V,200mA,DO-35, DIODE-SWITCHING;1N4148,100V,200mA,DO-35, DIODE-RECTIFIER;1N5397GP,600V,1.5A,DO-20 DIODE-RECTIFIER;TVR10G,400V,1.0A,DO-41,T DIODE-SWITCHING;1N4148,100V,200mA,DO-35, DIODE-RECTIFIER;1N4004,400V,1A,DO-41,TP DIODE-RECTIFIER;1N4004,400V,1A,DO-41,TP DIODE-RECTIFIER;1N4004,400V,1A,DO-41,TP DIODE-RECTIFIER;TVR10G,400V,1.0A,DO-41,T DIODE-SCHOTTKY;RB441Q,10V,100mA,DO-34,TP DIODE-SCHOTTKY;RB441Q,10V,100mA,DO-34,TP DIODE-SCHOTTKY;RB441Q,10V,100mA,DO-34,TP DIODE-SCHOTTKY;RB441Q,10V,100mA,DO-34,TP DIODE-SWITCHING;1N4148,100V,200mA,DO-35, DIODE-RECTIFIER;1N4004,400V,1A,DO-41,TP DIODE-ZENER;MTZJ5.6B,5.6V,5.45-5.73V,500 DIODE-ZENER;MTZJ5.6B,5.6V,5.45-5.73V,500 DIODE-ZENER;MTZJ6.8C,6.66-7.01V,500mW,DO DIODE-ZENER;MTZJ5.6B,5.6V,5.45-5.73V,500 DIODE-ZENER;MTZJ5.6B,5.6V,5.45-5.73V,500 DIODE-ZENER;MTZJ5.6B,5.6V,5.45-5.73V,500 DIODE-ZENER;MTZJ24B,22.61-23.77V,500mW,D DIODE-ZENER;MTZJ24B,22.61-23.77V,500mW,D DIODE-ZENER;MTZJ24B,22.61-23.77V,500mW,D DIODE-ZENER;UZ39BSB,35.36-37.19V,500MW,D DIODE-ZENER;TZP33A,33V,31-35V,1W,DO-41,T DIODE-ZENER;MTZJ15C,14.35-15.09V,500mW,D DIODE-SWITCHING;1N4148,100V,200mA,DO-35, DIODE-ZENER;MTZJ5.6B,5.6V,5.45-5.73V,500
! !
! !
....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4
DZ602 DZ603 DZ605 DZ801 DZ802 DZ803 DZ804 DZ805 DZ806 DZ808 DZ902 DZ903 DZ904 DZ905 DZ906 DZ907 DZ908 DZ909 DZ910 F801A F801B FA802S FA803S HIC201 HIC202 HIC203 HIC204 IC903 IC904 J231 J401 J412 J901 J904 L102 L103 L108 L109 L201 L202 L204 L207 L208 L209 L210 L212 L301 L302 L303 L401 L406 L407 L410 L601 L604 L605 L606 L607 L608 L609 L701 L702 L705 L706 L709 L710 L711 L801 L802 L803 L804 L806 L807 L809 L901 L902 L903
0403-000720 0403-000508 0403-000508 0403-001322 0403-000508 0403-001167 0403-000700 1203-001217 0403-000508 0403-001322 0403-000508 0403-000508 0403-000508 0403-000508 0403-000508 0403-000508 0403-000508 0403-000508 0403-000508 3602-000114 3602-000114 3601-001086 3601-001228 AA13-00093A AA13-00093A AA13-00093A AA13-00093A 1203-001944 1203-001943 2001-000449 2701-000114 3301-001223 3301-000287 2001-000281 2701-000200 2701-000115 2701-000114 2701-000114 2901-000297 2701-000114 2701-000184 3301-000287 2701-000146 2701-000168 2701-000168 2701-000168 2701-000114 3301-000287 3301-000287 2001-001038 2701-000114 2901-000297 3301-001223 2901-000297 2701-000169 2701-000177 2701-000177 2701-000177 2701-000177 2901-000297 2701-000177 2701-000177 2701-000177 2701-000177 2701-000168 2701-000168 2701-000114 3301-001223 3301-000287 3301-000287 3301-000287 3301-001223 2901-000297 3301-000287 2702-001094 2701-000184 2702-001094
DIODE-ZENER;MTZJ9.1B,9.1V,8.57-9.01V,500 DIODE-ZENER;MTZJ5.6B,5.6V,5.45-5.73V,500 DIODE-ZENER;MTZJ5.6B,5.6V,5.45-5.73V,500 DIODE-ZENER;MTZJ8.2B,7.78-8.19V,500mW,DO DIODE-ZENER;MTZJ5.6B,5.6V,5.45-5.73V,500 DIODE-ZENER;MTZJ30D,30V,29.02-30.51V,500 DIODE-ZENER;TZP33A,33V,31-35V,1W,DO-41,T IC-POSI.ADJUST REG.;431,TO-92,3P,4.58MIL DIODE-ZENER;MTZJ5.6B,5.6V,5.45-5.73V,500 DIODE-ZENER;MTZJ8.2B,7.78-8.19V,500mW,DO DIODE-ZENER;MTZJ5.6B,5.6V,5.45-5.73V,500 DIODE-ZENER;MTZJ5.6B,5.6V,5.45-5.73V,500 DIODE-ZENER;MTZJ5.6B,5.6V,5.45-5.73V,500 DIODE-ZENER;MTZJ5.6B,5.6V,5.45-5.73V,500 DIODE-ZENER;MTZJ5.6B,5.6V,5.45-5.73V,500 DIODE-ZENER;MTZJ5.6B,5.6V,5.45-5.73V,500 DIODE-ZENER;MTZJ5.6B,5.6V,5.45-5.73V,500 DIODE-ZENER;MTZJ5.6B,5.6V,5.45-5.73V,500 DIODE-ZENER;MTZJ5.6B,5.6V,5.45-5.73V,500 FUSE-HOLDER;-,-,30mohm FUSE-HOLDER;-,-,30mohm FUSE-AXIAL LEAD;125V,5A,FAST-ACTING,GLAS FUSE-AXIAL LEAD;125V,10A,FAST-ACTING,EPO IC HYBRID;-,DRGB001A,SIP,5P,-,TP IC HYBRID;-,DRGB001A,SIP,5P,-,TP IC HYBRID;-,DRGB001A,SIP,5P,-,TP IC HYBRID;-,DRGB001A,SIP,5P,-,TP IC-POSI.FIXED REG.;78RM33,TO-220,3P,-,PL IC-VOL. DETECTOR;7025,TO-92,3P,-,PLASTIC R-CARBON;2.2KOHM,5%,1/8W,AA,TP,1.8X3.2M INDUCTOR-AXIAL;10uH,10%,2.5x3.4mm CORE-FERRITE BEAD;AA,62ohm,3.5x0.8x5mm,CORE-FERRITE BEAD;AA,3.5x1.0x6.0mm,1500, R-CARBON;100OHM,5%,1/8W,AA,TP,1.8X3.2MM INDUCTOR-AXIAL;5.6uH,10%,4.2x9.8mm INDUCTOR-AXIAL;10uH,10%,3x7mm INDUCTOR-AXIAL;10uH,10%,2.5x3.4mm INDUCTOR-AXIAL;10uH,10%,2.5x3.4mm FILTER-EMI ON BOARD;-,3A,-,-,3.5x5,TP,INDUCTOR-AXIAL;10uH,10%,2.5x3.4mm INDUCTOR-AXIAL;4.7uH,10%,2.5x3.4mm CORE-FERRITE BEAD;AA,3.5x1.0x6.0mm,1500, INDUCTOR-AXIAL;2.2uH,10%,2.5x3.4mm INDUCTOR-AXIAL;3.3uH,5%,2.5x3.4mm INDUCTOR-AXIAL;3.3uH,5%,2.5x3.4mm INDUCTOR-AXIAL;3.3uH,5%,2.5x3.4mm INDUCTOR-AXIAL;10uH,10%,2.5x3.4mm CORE-FERRITE BEAD;AA,3.5x1.0x6.0mm,1500, CORE-FERRITE BEAD;AA,3.5x1.0x6.0mm,1500, R-CARBON(S);0.56OHM,5%,1/2W,AA,TP,2.4X6. INDUCTOR-AXIAL;10uH,10%,2.5x3.4mm FILTER-EMI ON BOARD;-,3A,-,-,3.5x5,TP,CORE-FERRITE BEAD;AA,62ohm,3.5x0.8x5mm,FILTER-EMI ON BOARD;-,3A,-,-,3.5x5,TP,INDUCTOR-AXIAL;3.9uH,10%,2.5x3.4mm INDUCTOR-AXIAL;33uH,10%,2.5x3.4mm INDUCTOR-AXIAL;33uH,10%,2.5x3.4mm INDUCTOR-AXIAL;33uH,10%,2.5x3.4mm INDUCTOR-AXIAL;33uH,10%,2.5x3.4mm FILTER-EMI ON BOARD;-,3A,-,-,3.5x5,TP,INDUCTOR-AXIAL;33uH,10%,2.5x3.4mm INDUCTOR-AXIAL;33uH,10%,2.5x3.4mm INDUCTOR-AXIAL;33uH,10%,2.5x3.4mm INDUCTOR-AXIAL;33uH,10%,2.5x3.4mm INDUCTOR-AXIAL;3.3uH,5%,2.5x3.4mm INDUCTOR-AXIAL;3.3uH,5%,2.5x3.4mm INDUCTOR-AXIAL;10uH,10%,2.5x3.4mm CORE-FERRITE BEAD;AA,62ohm,3.5x0.8x5mm,CORE-FERRITE BEAD;AA,3.5x1.0x6.0mm,1500, CORE-FERRITE BEAD;AA,3.5x1.0x6.0mm,1500, CORE-FERRITE BEAD;AA,3.5x1.0x6.0mm,1500, CORE-FERRITE BEAD;AA,62ohm,3.5x0.8x5mm,FILTER-EMI ON BOARD;-,3A,-,-,3.5x5,TP,CORE-FERRITE BEAD;AA,3.5x1.0x6.0mm,1500, INDUCTOR-RADIAL;10uH,10%,6x4mm INDUCTOR-AXIAL;4.7uH,10%,2.5x3.4mm INDUCTOR-RADIAL;10uH,10%,6x4mm
Samsung Electronics
www.rtv-horvat-dj.hr
7-3
Electrical Parts List
Level Loc. No. Code No.
Description ; Specification
Remark
Level Loc. No. Code No.
Description ; Specification
Remark
....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ....4 ..