Text preview for : ED1112S.pdf part of ED1112S ED1112S ED1112S
Back to : ED1112S.pdf | Home
11mm Rotary type Encoders-With Switch (11mm ±ÛÂড½s½X¾¹ -ªþ¶}Ãö )
ED1112S Part Number
ED1112S 20 -L 20 F
20 clicks Shaft Length
20 ¥dÂI ¶bªø
Shaft Type
¶b«¬
Dimensions ³W®æ¤Øo
Shaft Type ¶b«¬
http://www.song-huei.com.tw
mm Metal Shaft Rotary Potentiometer (9mm ª÷Äݶb±ÛÂà¹q¦ì¾¹ )
11mm Rotary type Encoders-With Switch (11mm ±ÛÂড½s½X¾¹ -ªþ¶}Ãö )
General ¤@¯ëS©Ê
(1 ) Scope
This specification applies to 12mm size low-profile rotary encoder (incremental type) for
microscopic current circuits used in electronic equipment.
(2) Standard atmospheric conditions
Unless otherwise specified, the range of atmospheric conditions for making measurements
and test is as following limits:
Ambient temperature : 15¢J¡ã 35¢J
Relative humidity : 25 % ¡ã 85 %
Air pressure : 86k Pa ¡ã 106k Pa
If there is any objection, the inspection should be preceded as following:
Ambient temperature
Relative humidity : 63 % ¡ã 67 %
Air pressure : 86k Pa¡ã 106k Pa
(3) Operating temperature range : ¡Ð 10¢J ¡ã ¡Ï 70¢J
(4) Storage temperature range : ¡Ð 40¢J ¡ã ¡Ï 85¢J
Rating ÃB©w¥\²v
(1) Rated Voltage : D.C. 5V.10mA ( 1 mA / min. )
(2) Maximum operating current ( resistive load )
Each lead : 0.5 mA ( Max. : 5mA Min. : 0.5 mA )
Common lead : 1.0 mA ( Max. : 10mA Min. : 0.5 mA )
Mechanical characteristics ¾÷±ñ¯S©Ê
(1) Total rotational 360¢X Endless)
(
(2) Detent torque 5 ~ 19 mN. (51.0 ~ 193.8 gf. cm. ) Shaft rotational at -10¢J ~ +5¢J
(3) Number and Position of detents 20 detents ( Step angle : 18¢Ó ¡ 3¢X
X )
(4) Terminal strength A static load of 5N (0.51Kgf) shall be applied to the tip of terminals
for 1 min any direction.
(5) Push-pull Strength of shaft Push and pull static load of 10 N (10.2 Kgf) shall be to
the shaft in the axial direction for 10S. (After installing)
(6) Shaft wobble 0.7 xL/30 mm p-p MAX.( L : shaft length) Under Conditions as below.
A momentary load of 50mN¡D shall be applied at the point 5 mm form
m
the tip of the shaft in a direction perpendicular to the axis of shaft.
http://www.song-huei.com.tw
(7) Side thrust strength of shaft Static load of 20 N (2.04 Kg) shall be to the shaft in the
axial direction for 10S. (After installing)
(8) Using angle of rotary shaft 5¢X
MAX.
Electrical characteristics ¹q®ð¯S©Ê
(1) Output signal format 2 phase - different signals(signal A signal B)Details
shown in < PH 1 > ( The broken line shows detente position )
Shaft rotational Direction Signal Output
OFF
A (Terminal A ~ C )
ON
C¡O W¡O OFF
B (Terminal B ~ C )
ON
OFF
A (Terminal A ~ C )
ON
C¡O C¡O W¡O OFF
B (Terminal B ~ C )
ON
¡y PH 1.¡z
(2) Resolution 20 pulses /360¢X each phase . Under Conditions as below,
for
number of pulses in 360¢X
rotation.
(3) Withstand Voltage A voltage of 300V A.C. shaft be applied for 1min between
individual terminals and bushing.
(4) Insulation resistance Between individual terminals and bushing ; 100 M£[ min.
Under conditions as bushing, Measurement shaft be made
under the condition which a voltage 250V D.C. is applied
between individual terminals and bushing.
(5) Phase-difference Measurement shaft be made under the condition which the shaft is
rotated in constant speed. In < PH2 >
C.W T C.C.W T
off off
Signal A Signal A
on on
(Terminal A ~ C) (Terminal A ~ C)
off off
Signal B Signal B
on on
(Terminal B ~ C) (Terminal B ~ C)
£G T £G T
¡° MIN.£G T = 0.08T
http://www.song-huei.com.tw
(6) Switching Characteristics Measurement shall be made under the condition as
follows.
Shaft rotational speed : 360¢XS
/
Test circuit : < PH3 >
( note ) Code¡Ð ON area : The area which the voltage is 1.5V or
less.
Code¡Ð OFF area : The area which the voltage is 3.5V or
more.
DC5V
OFF
10K£[ 10K£[
¡[ Terminal A ¡[ Terminal B 3.5 V
1.5 V
Encoder
ON
Terminal C t1 t2 t3
¡y PH3. ¡z ¡y PH4. ¡z
(6-1) Chattering Conditions : Specified by the signal¡¦s passage time form 1.5V to 3.5V of each
switching position ( code OFF ON or ON OFF )
Specifications : t 1 , t 3 ¡Ø 2 mS
(6-2) Noise (Bounce) Conditions: Specified by the time of voltage change exceed 1.5V in
code-ON area. When the bounce has code-ON time Less than 1 mS
between chattering ( t1 or t3 ) , the voltage change shall be regarded as a
part of chattering. When the code-ON time between 2 bounces is less
than 1 mS , hey are regarded as 1 linked bounce.
Specifications : t 2 ¡Ø 2 mS
(6-3) Noise Conditions: The voltage change in code-OFF area.
Specifications: 3.5V MIN.
Endurance characteristics -@¤[¯S©Ê
(1) Rotational life Conditions: The shaft of encoder shall be rotated to 30,000 cycles at a
speed of 600~1000H without electrical load, after which measurements
shall be made.
Specifications : Chattering t1 , t2¡Ø 3 mS
Detent Toque -30% ~ +10%
http://www.song-huei.com.tw
(2) Damp heat The encoder shall be stored at temperature of 40¡Ó 2¢J with relative
humidity of 90% to 95% for 240¡Ó 10 in a thermostatic chamber. And
then the encoder shall be subjected to standard atmospheric conditions for
1.5 H. After which measurements shall be made.
(3) Dry heat The encoder shall be stored at a temperature of 80¢J ¡Ó 3¢J for 240 ¡Ó 10 H in
a thermostatic chamber . And then the encoder shall be subjected to
standard atmospheric conditions for 1.5H.After witch measurement shaft
be made.
(4) Cold The encoder shall be stored at a temperature of 40 ¢J ¡Ó 3¢J for 240 ¡Ó 10 H
in a thermostatic chamber . And then the encoder shall be subjected to
standard atmospheric conditions for 1.5 H. After witch measurement shall
be made.
(5) Free falling The encoder shall be fallen freely at any posture from 60 cm. height to the
concrete floor covered with vinyl - tile. After which measurement shall be
made.
(6) Vibration The following vibration shall be applied to the encoder, after which
measurement shall be made: The entire frequency range from 10Hz to
55Hz and return to 10Hz shall be transverse in 1 min. Amplitude (total
excursion): 1.5 mm This motion shall be applied for a period of 2H in
each of 3mutually perpendicular axes.
Soldering conditions ²k±µø¥ó
(1) Manual soldering Bit temperature of soldering iron : 300¢J or less.
Application time of soldering iron : within 3s.
(2) Dip soldering Printed-wiring board: Single-sided copper clad laminate board with
thickness of 1.6mm.
Flex : Specific gravity : 0.82 or more.
Flux shall be applied to the board using a bubble foaming type fluxer.
The board shall be soaked in the flux bubble only to the middle of its thickness.
Flux shall not come into contact with the component side surface.
Preheating : Surface temperature of board : 100¢J or less.
Preheating time : Within 2 min.
Soldering : Solder temperature : 260¢J or less.
Immersion time : Within 3 s¡Ó 1s.
Maintaining : The encoder has to maintain temperature between at 25¡Ó 2¢J in
the house , and the relative humidity should be within at 35¢M¡ã 85¢MPH. Keep out of
humidity and sun.
Apply the above soldering process for 1 or 2 times.
http://www.song-huei.com.tw
(3) Note for soldering method Solder Terminal
Avoid wiring and soldering that causes
solder to flow out to the top of P.C. Board
as shown. A contact failure may occur in
the terminal section.
Sold P.C.
Other ¨ä¥L
(1) To assure smooth rotation of a potentiometer at extremely low temperature, dry and no silicon or
cyanogen base gas atmosphere.
(2) The process and design of encoder switch numbers of pulse. Please be considered speed, time and
noise of pules. After all confirmation then using the encoder switch.
(3) The detent stability on a signal is standard. A signal with OFF position is more stability.
(4) Avoid contacting dew or water drops with base body might occur extraordinary on the output
wherefrom.
Push Switch part ¶}Ãö±À³¡¤
1. Rating D.C. 5V 10mA ( 1 mA min. )
2. Electrical Characteristics
(1) Contact Resistance Conditions : Testing method under DC 5V 1mA min.
Specifications : First period 100M£[ ; 200M£[ after the end of useful life is reached.
(2) Sliding Noise Conditions : specified by the signal¡¦s passage time from 1 second for
each time rotation.( OFF ON OFF) Specifications: 10ms max.
(3) Insulation Resistance Between terminal and installment board has DC50V 1mA. Insulation
resistance 10M£[ max.
(4) Withstand Voltage Between terminal and installment board has AC50V / 1 minute.
(5) Remark Between shaft and terminal of switch are insulated.
3. Mechanical characteristics
(1) Switch circuit, the number of contact Single pole and single throw.
(2) Travel of switch 0.5 mm (3) Operating Force of Switch 360 gf
4. Reliability
The shaft of encoder shall be rotated to 20,000 cycles at a speed of 500 cycles per hour without electrical
load, after which measurements should be made. However, an interim measurement should be made
immediately after 5,000 cycles. The contact resistance should be 200 m£[ max. (Shaft push-pull strength
shall be 1 kgf.cm max.)
http://www.song-huei.com.tw