Text preview for : 20AS25+Parts,+Service+Manual.pdf part of TOSHIBA 20AS25 COMPLETE FACTORY MANUAL
Back to : 20AS25+Parts,+Service+Man | Home
FILE NO. 050-200501
SERVICE MANUAL
COLOR TELEVISION
20AS25
DOCUMENT CREATED IN JAPAN, Jan., 2005
SERVICING NOTICES ON CHECKING
1. KEEP THE NOTICES
As for the places which need special attentions, they are indicated with the labels or seals on the cabinet, chassis and parts. Make sure to keep the indications and notices in the operation manual.
6. AVOID AN X-RAY
Safety is secured against an X-ray by considering about the cathode-ray tube and the high voltage peripheral circuit, etc. Therefore, when repairing the high voltage peripheral circuit, use the designated parts and make sure not modify the circuit. Repairing except indicates causes rising of high voltage, and it emits an X-ray from the cathoderay tube.
2. AVOID AN ELECTRIC SHOCK
There is a high voltage part inside. Avoid an electric shock while the electric current is flowing.
3. USE THE DESIGNATED PARTS
The parts in this equipment have the specific characters of incombustibility and withstand voltage for safety. Therefore, the part which is replaced should be used the part which has the same character. Especially as to the important parts for safety which is indicated in the circuit diagram or the table of parts as a mark, the designated parts must be used.
7. PERFORM A SAFETY CHECK AFTER SERVICING
Confirm that the screws, parts and wiring which were removed in order to service are put in the original positions, or whether there are the portions which are deteriorated around the serviced places serviced or not. Check the insulation between the antenna terminal or external metal and the AC cord plug blades. And be sure the safety of that.
(INSULATION CHECK PROCEDURE)
4. PUT PARTS AND WIRES IN THE ORIGINAL POSITION AFTER ASSEMBLING OR WIRING
There are parts which use the insulation material such as a tube or tape for safety, or which are assembled in the condition that these do not contact with the printed board. The inside wiring is designed not to get closer to the pyrogenic parts and high voltage parts. Therefore, put these parts in the original positions.
5. TAKE CARE TO DEAL WITH THE CATHODE-RAY TUBE
In the condition that an explosion-proof cathoderay tube is set in this equipment, safety is secured against implosion. However, when removing it or serving from backward, it is dangerous to give a shock. Take enough care to deal with it.
1. Unplug the plug from the AC outlet. 2. Remove the antenna terminal on TV and turn on the TV. 3. Insulation resistance between the cord plug terminals and the eternal exposure metal [Note 2] should be more than 1M ohm by using the 500V insulation resistance meter [Note 1]. 4. If the insulation resistance is less than 1M ohm, the inspection repair should be required.
[Note 1]
If you have not the 500V insulation resistance meter, use a Tester.
[Note 2]
External exposure metal: Antenna terminal Earphone jack
HOW TO ORDER PARTS
Please include the following informations when you order parts. (Particularly the VERSION LETTER.) 1. MODEL NUMBER and VERSION LETTER The MODEL NUMBER can be found on the back of each product and the VERSION LETTER can be found at the end of the SERIAL NUMBER. 2. PART NO. and DESCRIPTION You can find it in your SERVICE MANUAL.
IMPORTANT
Inferior silicon grease can damage IC's and transistors. When replacing an IC's or transistors, use only specified silicon grease (YG6260M). Remove all old silicon before applying new silicon.
A1-1
ABOUT LEAD FREE SOLDER (PbF)
Distinction of PbF PCB:
PCBs (manufactured) using lead free solder will have a PbF printing on the PCB. (Please refer to figures.)
Caution: · Pb free solder has a higher melting point than standard solder;
Typically the melting point is 50°F~70°F(30°C~40°C) higher. Please use a soldering iron with temperature control and adjust it to 650°F ± 20°F (350°C ± 10°C).
· ·
In case of using high temperature soldering iron, please be carefull not to heat too long. Pb free solder will tend to splash when heated too high (about 1100°F/ 600°C). All products with the printed circuit board with PbF printing must be serviced with lead free solder. When soldering or unsoldering, completely remove all of the solder from the pins or solder area, and be sure to heat the soldering points with the lead free solder until it melts sufficiently.
Recommendations
Recommended lead free solder composition is Sn-3.0Ag-0.5Cu.
A1-2
CONTENTS
SERVICING NOTICES ON CHECKING ...................................................................................................... HOW TO ORDER PARTS ........................................................................................................................... IMPORTANT ................................................................................................................................................ ABOUT LEAD FREE SOLDER (PbF) ......................................................................................................... CONTENTS ................................................................................................................................................. GENERAL SPECIFICATIONS .................................................................................................................... DISASSEMBLY INSTRUCTIONS 1.REMOVAL OF ANODE CAP .............................................................................................................. 2.REMOVAL AND INSTALLATION OF FLAT PACKAGE IC ............................................................... SERVICE MODE LIST ................................................................................................................................. CONFIRMATION OF HOURS USED .......................................................................................................... WHEN REPLACING EEPROM (MEMORY) IC ........................................................................................... ELECTRICAL ADJUSTMENTS .................................................................................................................. BLOCK DIAGRAM ...................................................................................................................................... PRINTED CIRCUIT BOARDS MAIN/CRT ............................................................................................................................................... SCHEMATIC DIAGRAMS MICON/CHROMA/TUNER ...................................................................................................................... TV POWER ............................................................................................................................................. DEFLECTION/CRT ................................................................................................................................. SOUND/AV ............................................................................................................................................. WAVEFORMS ............................................................................................................................................. MECHANICAL EXPLODED VIEW .............................................................................................................. MECHANICAL REPLACEMENT PARTS LIST .......................................................................................... ELECTRICAL REPLACEMENT PARTS LIST ............................................................................................ A1-1 A1-1 A1-1 A1-2 A2-1 A3-1~A3-5 B1-1 B2-1, B2-2 C-1 C-1 C-1 D-1~D-4 E-1, E-2 F-1~F-4 G-1, G-2 G-3, G-4 G-5, G-6 G-7, G-8 H-1, H-2 I-1, I-2 J1-1 J2-1~ J2-3
A2-1
GENERAL SPECIFICATIONS
G-1 TV System CRT CRT Size / Visual Size CRT Type Deflection Magnetic Field BV/BH 19 inch / 480.0mmV Normal 90 degree +0.35G/0.30G NTSC 1Speaker Bottom 3 Inch 8 ohm 1.5 W 1.0 W No US System M 1Tuner USA(W/ CATV) F-Synth VHF/UHF 75 ohm 2 - 69, 4A, A-5 - A-1, A - I, J - W, W+1 - W+84 45.75MHz 41.25MHz 4.50MHz No No Yes 120V AC 60Hz at AC Stand by (at AC) Per Year Power Fuse Safety Radiation X-Radiation Operation Storage 73 W at AC 120 V 60 Hz 5 W at AC 120 V 60 Hz -kWh/Year Yes UL FCC DHHS +5oC ~ +40oC -20oC ~ +60oC Less than 80% RH
Color System Speaker Position Size Impedance MAX 10%(Typical)
Sound Output NTSC3.58+4.43 /PAL60Hz Broadcasting System Tuner and Receive CH
G-2
Tuning System
System Destination Tuning System Input Impedance CH Coverage Picture(FP) Sound(FS) FP-FS
Intermediate Frequency Preset CH Stereo/Dual TV Sound Tuner Sound Muting Power Source Power Consumption
G-3
Power
AC DC
Protector G-4 Regulation
G-5 G-6
Temperature Operating Humidity
A3-1
GENERAL SPECIFICATIONS
G-7 On Screen Display Menu Menu Type Picture Contrast Brightness Color Tint Sharpness Audio Bass Treble Balance BBE On/Off Stable Sound On/Off CH Set Up TV/CABLE(CATV) Auto CH Memory Add/ Delete Language V-chip Lock On Timer CH Label Favorite CH Color Stream DVD/DTV Control Level Volume Brightness Contrast Color Tint Sharpness Tuning Bass Treble Balance Back Light Stereo,Audio Output,SAP Video Color Stream Channel(TV/Cable) CH Label Game Timer Sleep Timer Sound Mute V-chip Rating G-8 G-9 OSD Language Clock and Timer Sleep Timer Max Time Step Program(On Timer ) more than Yes Yes Yes Yes Yes Yes Yes No No No No No No Yes No Yes No Yes Yes Yes Yes English Yes Yes Yes Yes Yes Yes Yes Yes No No No Yes Character Yes Yes Yes Yes Yes Yes No No No No No No
French
Spanish
On Timer Wake Up Timer Timer Back-up (at Power Off Mode)
120 Min 10 Min Yes No -Min Sec
A3-2
GENERAL SPECIFICATIONS
G-10 Remote Control Unit Glow in Dark Remocon Format Custom Code Power Source Total Keys Keys RC-EH Yes[From '04 DEC O/R] Toshiba 40-BF h 3V UM-4 x 2 pcs 27 Keys Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes No Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes No No Yes Yes No No No No No No No No No No No No No
Voltage(D.C) UM size x pcs Power 1 2 3 4 5 6 7 8 9 0 100 CH Up CH Down Volume Up Volume Down TV/Caption/Text CH1/CH2 TV/Video(TV/AV) CH RTN/CH ENT(Quick View) Sleep RE Call(Call) Reset Menu Enter Mute Exit MTS(Audio Select) Set + Set CH Up(VCR) CH Down(VCR) Pause/Still TV/VCR(VCR) Code FF Rew Rec Play Stop TV VCR Cable
Multi Brand Keys
A3-3
GENERAL SPECIFICATIONS
G-11 Features Auto Degauss Auto Shut Off Canal+ CATV Anti-theft Rental Memory(Last CH) Memory(Last Volume) V-Chip Type BBE Auto Search CH Allocation SAP Just Clock Function CH Label VM Circuit Full OSD Premiere Comb Filter Auto CH Memory Hotel Lock Closed Caption Stable Sound FBT Leak Test Protect CH Lock Video Lock Game Timer (Max Time:120 Min) Stable Sound Energy Star Power On Memory Favorite CH Owner's Manual Language W/ Warranty Remote Control Unit Rod Antenna Poles Terminal Loop Antenna Terminal U/V Mixer DC Car Cord (Center+) Guarantee Card Warning Sheet Circuit Diagram Antenna Change Plug Service Facility List Important Safety Instruction Dew/AHC Caution Sheet AC Plug Adapter Quick Set-up Sheet Battery UM size x pcs OEM Brand AC Cord AV Cord (2Pin-1Pin) Registration Card (NDL Card) ESP Card PTB Sheet 300 ohm to 75 ohm Antenna Adapter Yes Yes No Yes No No Yes Yes Yes USA,ORION Type No No No No No No No No No No Lines Yes No Yes No Yes Yes Yes Yes No No Yes No English / Spanish No Yes No
G-12
Accessories
No No No Yes No No No No No No No No Yes UM4 x 2 No No No No No No No
A3-4
GENERAL SPECIFICATIONS
G-13 Interface Switch Front Power System Select Main Power SW Sub Power Channel Up/Reset Channel Down/Enter Volume Up/Set Up Volume Down/Set Down MENU=Volume Up+Volume Down AC/DC TV/CATV Selector Degauss Main Power SW Power Stand-by On Timer Video Input Audio Input Other Terminal Video Input(Rear1) Video Input(Rear2) Audio Input(Rear1) Audio Input(Rear2) Video Output Audio Output Euro Scart Color Stream Diversity Ext Speaker DC Jack 12V(Center +) VHF/UHF Antenna Input AC Outlet Approx. W x D x H (mm) Net (Approx.) Gross (Approx.) Content Material Dimensions W x D x H(mm) Description of Origin Gift Box Material Dimensions W x D x H(mm) Design Description of Origin Drop Test Height (cm) Container Stuffing Cabinet Cabinet Front Cabinet Rear PCB Non-Halogen Demand Eyelet Demand Pb Free Yes No No No Yes Yes Yes Yes Yes No No No No Yes No No RCA RCA x 1 No No No No No No No No No No No No F Type No 488 x 465 x 416 17.5kg ( 38.6 lbs) 20.0kg ( 44.1lbs) No ---Sets -/--- x -- x -No Yes Double/Brown 546 x 526 x 472 As per Buyer's Yes Natural Dropping At 1 Corner / 2 Edges / 4 Surfaces 60 (ORION SPEC:46) 436 Sets/40' container PS 94V0 DECABROM PS 94V0 DECABROM No Yes Phase3
Rear
Indicator
Terminals
Front
Rear
G-14 G-15 G-16
Set Size Weight Carton Master Carton
G-17
Cabinet Material
G-18
Environment
A3-5
DISASSEMBLY INSTRUCTIONS
1. REMOVAL OF ANODE CAP
Read the following NOTED items before starting work. * After turning the power off there might still be a potential voltage that is very dangerous. When removing the Anode Cap, make sure to discharge the Anode Cap's potential voltage. * Do not use pliers to loosen or tighten the Anode Cap terminal, this may cause the spring to be damaged. REMOVAL 1. Follow the steps as follows to discharge the Anode Cap. (Refer to Fig. 1-1.) Connect one end of an Alligator Clip to the metal part of a flat-blade screwdriver and the other end to ground. While holding the plastic part of the insulated Screwdriver, touch the support of the Anode with the tip of the Screwdriver. A cracking noise will be heard as the voltage is discharged. Location of Anode Cap 3. After one side is removed, pull in the opposite direction to remove the other. NOTE Take care not to damage the Rubber Cap. INSTALLATION 1. Clean the spot where the cap was located with a small amount of alcohol. (Refer to Fig. 1-3.)
Fig. 1-3 GND on the CRT NOTE Confirm that there is no dirt, dust, etc. at the spot where the cap was located. 2. Arrange the wire of the Anode Cap and make sure the wire is not twisted. 3. Turn over the Rubber Cap. (Refer to Fig. 1-4.)
Screwdriver
CRT Support Alligator Clip Fig. 1-4
GND on the CRT
Fig. 1-1 4. Insert one end of the Anode Support into the anode button, then the other as shown in Fig. 1-5.
2. Flip up the sides of the Rubber Cap in the direction of the arrow and remove one side of the support. (Refer to Fig. 1-2.) Rubber Cap
CRT CRT Support Fig. 1-2
Support Fig. 1-5
5. Confirm that the Support is securely connected. 6. Put on the Rubber Cap without moving any parts. B1-1
DISASSEMBLY INSTRUCTIONS
2. REMOVAL AND INSTALLATION OF FLAT PACKAGE IC
REMOVAL 1. Put the Masking Tape (cotton tape) around the Flat Package IC to protect other parts from any damage. (Refer to Fig. 2-1.) NOTE Masking is carried out on all the parts located within 10 mm distance from IC leads.
Blower type IC desoldering machine
3. When IC starts moving back and forth easily after desoldering completely, pickup the corner of the IC using a tweezers and remove the IC by moving with the IC desoldering machine. (Refer to Fig. 2-3.) NOTE Some ICs on the PCB are affixed with glue, so be careful not to break or damage the foil of each IC leads or solder lands under the IC when removing it.
Masking Tape (Cotton Tape)
IC
Tweezers
Fig. 2-1
IC
2. Heat the IC leads using a blower type IC desoldering machine. (Refer to Fig. 2-2.) NOTE Do not add the rotating and the back and forth directions force on the IC, until IC can move back and forth easily after desoldering the IC leads completely. 4. Peel off the Masking Tape.
Fig. 2-3
5. Absorb the solder left on the pattern using the Braided Shield Wire. (Refer to Fig. 2-4.) NOTE Do not move the Braided Shield Wire in the vertical direction towards the IC pattern.
Blower type IC desoldering machine
Braided Shield Wire
Soldering Iron
IC
Fig. 2-2
IC pattern
Fig. 2-4
B2-1
DISASSEMBLY INSTRUCTIONS
INSTALLATION 1. Take care of the polarity of new IC and then install the new IC fitting on the printed circuit pattern. Then solder each lead on the diagonal positions of IC temporarily. (Refer to Fig. 2-5.) 4. When bridge-soldering between terminals and/or the soldering amount are not enough, resolder using a Thin-tip Soldering Iron. (Refer to Fig. 2-8.)
Thin-tip Soldering Iron
IC
Soldering Iron
Fig. 2-8 5. Finally, confirm the soldering status on four sides of the IC using a magnifying glass. Confirm that no abnormality is found on the soldering position and installation position of the parts around the IC. If some abnormality is found, correct by resoldering. NOTE When the IC leads are bent during soldering and/or repairing, do not repair the bending of leads. If the bending of leads are repaired, the pattern may be damaged. So, always be sure to replace the IC in this case.
Solder temporarily
Solder temporarily
Fig. 2-5 2. Supply the solder from the upper position of IC leads sliding to the lower position of the IC leads. (Refer to Fig. 2-6.)
Solder
Soldering Iron
IC
Supply soldering from upper position to lower position
Fig. 2-6 3. Absorb the solder left on the lead using the Braided Shield Wire. (Refer to Fig. 2-7.) NOTE Do not absorb the solder to excess.
Soldering Iron IC
Braided Shield Wire
Fig. 2-7 B2-2
SERVICE MODE LIST
This unit provided with the following SERVICE MODES so you can repair, examine and adjust easily. To enter the Service Mode, press both set key and remote control key for more than 2 seconds. Set Key VOL. (-) MIN Remocon Key 0 Releasing of V-CHIP PASSWORD. Initialization of the factory. NOTE: Do not use this for the normal servicing. If you set a factory initialization, the memories are reset such as the channel setting, and the POWER ON total hours. POWER ON total hours is displayed on the screen. Refer to the "CONFIRMATION OF HOURS USED". VOL. (-) MIN 6 Can be checked of the INITIAL DATA of MEMORY IC. Refer to the "WHEN REPLACING EEPROM (MEMORY) IC". VOL. (-) MIN 9 Display of the Adjustment MENU on the screen. Refer to the "ELECTRICAL ADJUSTMENT" (On-Screen Display Adjustment). Operations
VOL. (-) MIN
1
CONFIRMATION OF HOURS USED
POWER ON total hours can be checked on the screen. Total hours are displayed in 16 system of notation. NOTE: If you set a factory initialization, the total hours is reset to "0". ADDRESS DATA 1. Set the VOLUME to minimum. 2. Press both VOL. DOWN button on the set and Channel button (6) on the remote control for more than 2 seconds. Initial setting content of MEMORY IC. INIT 00 50 3. After the confirmation of using hours, turn off the power. POWER ON total hours. CRT ON 0010
= (16 x 16 x 16 x thousands digit value) + (16 x 16 x hundreds digit value) + (16 x tens digit value) + (ones digit value)
FIG. 1
WHEN REPLACING EEPROM (MEMORY) IC
If a service repair is undertaken where it has been required to change the MEMORY IC, the following steps should be taken to ensure correct data settings while making reference to TABLE 1. NOTE: No need setting for after INI 0F due to the adjustment value. INI 00 +0 50 +1 04 +2 EB +3 4E +4 57 +5 B3 +6 24 +7 69 +8 39 +9 00 +A 0C +B 05 +C 90 +D AE +E 00 +F 07
Table 1 1. Enter DATA SET mode by setting VOLUME to minimum. 2. Press both VOL. DOWN button on the set and Channel button (6) on the remote control for more than 2 seconds. ADDRESS and DATA should appear as FIG 1. 3. ADDRESS is now selected and should "blink". Using the VOL. +/- button on the remote, step through the ADDRESS until required ADDRESS to be changed is reached. 4. Press ENTER to select DATA. When DATA is selected, it will "blink". 5. Again, step through the DATA using VOL. +/- button until required DATA value has been selected. 6. Pressing ENTER will take you back to ADDRESS for further selection if necessary. 7. Repeat steps 3 to 6 until all data has been checked. 8. When satisfied correct DATA has been entered, turn POWER off (return to STANDBY MODE) to finish DATA input. After the data input, set to the initializing of shipping. 9. Turn POWER on. 10. Press both VOL. DOWN button on the set and Channel button (1) on the remote control for more than 2 seconds. 11. After the finishing of the initializing of shipping, the unit will turn off automatically. The unit will now have the correct DATA for the new MEMORY IC.
C-1
ELECTRICAL ADJUSTMENTS
1. ADJUSTMENT PROCEDURE
Read and perform these adjustments when repairing the circuits or replacing electrical parts or PCB assemblies. CAUTION · Use an isolation transformer when performing any service on this chassis. · Before removing the anode cap, discharge electricity because it contains high voltage. · When removing a PCB or related component, after unfastening or changing a wire, be sure to put the wire back in its original position. · When you exchange IC and Transistor for a heat sink, apply the silicon grease on the contact section of the heat sink. Before applying new silicon grease, remove all the old silicon grease. (Old grease may cause damages to the IC and Transistor.) Prepare the following measurement tools for electrical adjustments. 1. Oscilloscope 2. Digital Voltmeter 3. Pattern Generator On-Screen Display Adjustment 1. In the condition of NO indication on the screen. Press the VOL. DOWN button on the set and the Channel button (9) on the remote control for more than 2 seconds to appear the adjustment mode on the screen as shown in Fig. 1-1. TV
2. BASIC ADJUSTMENTS
2-1: CUT OFF 1. Adjust the unit to the following settings. R.DRIVE=10, B.DRIVE=10, R.BIAS=64, G.BIAS=64, B.BIAS=64, BRI.CENT=100, CONT.MAX=60. 2. Place the set with Aging Test for more than 15 minutes. 3. Activate the adjustment mode display of Fig. 1-1 and press the channel button (01) on the remote control to select "CUT OFF". 4. Adjust the Screen Volume until a dim raster is obtained. 2-2: WHITE BALANCE NOTE: Adjust after performing CUT OFF adjustment. 1. Place the set with Aging Test for more than 10 minutes. 2. Receive the gray scale pattern from the Pattern Generator. 3. Using the remote control, set the brightness and contrast to normal position. 4. Activate the adjustment mode display of Fig. 1-1 and press the channel button (10) on the remote control to select "R. BIAS". 5. Press the CH. UP/DOWN button on the remote control to select the "R. BIAS", "G. BIAS", "B. BIAS", "R. DRIVE" or "B. DRIVE". 6. Adjust the VOL. UP/DOWN button on the remote control to whiten the R. BIAS, G. BIAS, B. BIAS, R. DRIVE, and B. DRIVE at each step tone sections equally. 7. Perform the above adjustments 5 and 6 until the white color is looked like a white. 2-3: FOCUS 1. Receive the monoscope pattern. 2. Turn the Focus Volume fully counterclockwise once. 3. Adjust the Focus Volume until picture is distinct.
00 OSD
28 Fig. 1-1
2-4: HORIZONTAL PHASE 1. Receive the monoscope pattern. 2. Using the remote control, set the brightness and contrast to normal position. 3. Activate the adjustment mode display of Fig. 1-1 and press the channel button (05) on the remote control to select "H. PHAS". 4. Press the VOL. UP/DOWN button on the remote control until the SHIFT quantity of the OVER SCAN on right and left becomes minimum. 2-5: VERTICAL SHIFT 1. Receive the monoscope pattern. 2. Using the remote control, set the brightness and contrast to normal position. 3. Activate the adjustment mode display of Fig. 1-1 and press the channel button (07) on the remote control to select "V. SFT". 4. Press the VOL. UP/DOWN button on the remote control until the horizontal line becomes fit to the notch of the shadow mask.
3. Use the Channel UP/DOWN button or Channel button (0-9) on the remote control to select the options shown in Fig. 1-2. 4. Press the MENU button on the remote control to end the adjustments.
NO. 00 01 04 05 06 07 08 09 10 11 12 13 14 15 FUNCTION OSD H CUT OFF H. VCO H. PHASE V. SIZE V. SHIFT R DRIVE B DRIVE R BIAS G BIAS B BIAS BRIGHT CENT BRIGHT MAX BRIGHT MIN NO. 16 17 18 19 20 21 22 23 24 25 26 27 28 29 FUNCTION CONTRAST CENT CONTRAST MAX CONTRAST MIN COLOR CENTER COLOR MAX COLOR MIN TINT SHARPNESS FM LEVEL LEVEL SEPARATION1 SEPARATION2 TEST MONO TEST STEREO
Fig. 1-2 D-1
ELECTRICAL ADJUSTMENTS
2-6: VERTICAL SIZE 1. Receive the monoscope pattern. 2. Using the remote control, set the brightness and contrast to normal position. 3. Activate the adjustment mode display of Fig. 1-1 and press the channel button (06) on the remote control to select "V. SIZE". 4. Press the VOL. UP/DOWN button on the remote control until the SHIFT quantity of the OVER SCAN on upside and downside becomes 10 ± 2%. 2-7: SUB BRIGHTNESS 1. Receive the monoscope pattern. (RF Input) 2. Using the remote control, set the brightness and contrast to normal position. 3. Activate the adjustment mode display of Fig. 1-1 and press the channel button (13) on the remote control to select "BRI.CENT". 4. Press the VOL. UP/DOWN button on the remote control until the white 10% is starting to be visible 5. Receive the monoscope pattern. (Audio Video Input) 6. Press the TV/VIDEO button on the remote control to set to the AV mode. Then perform the above adjustments 2~4. 2-8: SUB TINT/SUB COLOR 1. Receive the color bar pattern. 2. Connect the oscilloscope to TP023. 3. Activate the adjustment mode display of Fig. 1-1 and press the channel button (22) on the remote control to select "TINT". 4. Press the VOL. UP/DOWN button on the remote control until the section "A" becomes as straight line (Refer to Fig. 2-1) 5. Connect the oscilloscope to TP022. 6. Activate the adjustment mode display of Fig. 1-1 and press the channel button (19) on the remote control to select "COL.CENT". 7. Press the VOL. UP/DOWN button on the remote control until the red color level is adjusted to 120 ± 5% of the white level. (Refer to Fig. 2-2) 8. Receive the color bar pattern. (Audio Video Input) 9. Press the TV/VIDEO button on the remote control to set to the AV mode. Then perform the above adjustments 2~7 white 100% red 120% 2-9: SUB CONTRAST 1. Activate the adjustment mode display of Fig. 1-1 and press the channel button (17) on the remote control to select "CONT. MAX". 2. Press the VOL. UP/DOWN button on the remote control until the contrast step No. becomes "60". 3. Receive a broadcast and check if the picture is normal. 4. Press the TV/VIDEO button on the remote control to set to the AV mode. Then perform the above adjustments 1~3. 2-10: OSD HORIZONTAL 1. Activate the adjustment mode display of Fig. 1-1. 2. Press the VOL. UP/DOWN button on the remote control until the difference of A and B becomes minimum. (Refer to Fig. 2-3) Fig. 2-2
TV
00 OSD A
28 B
Fig. 2-3
2-11: Confirmation of Fixed Value (Step No.) Please check if the fixed values of the each adjustment items are set correctly referring below. (RF/AV) NO. 04 14 15 16 18 20 21 23 24 25 26 27 D-2 FUNCTION STEP NO. H. VCO 04 BRIGHT MAX 183 BRIGHT MIN 60 CONTRAST CENT 30 CONTRAST MIN 17 COLOR MAX 74 COLOR MIN 00 SHARPNESS 45 FM LEVEL 00 LEVEL 00 SEPARATION1 00 SEPARATION2 00
"A"
Fig. 2-1
ELECTRICAL ADJUSTMENTS
3. PURITY AND CONVERGENCE ADJUSTMENTS
NOTE 1. Turn the unit on and let it warm up for at least 30 minutes before performing the following adjustments. 2. Place the CRT surface facing east or west to reduce the terrestrial magnetism. 3. Turn ON the unit and demagnetize with a Degauss Coil. 3-1: STATIC CONVERGENCE (ROUGH ADJUSTMENT) 1. Tighten the screw for the magnet. Refer to the adjusted CRT for the position. (Refer to Fig. 3-1) If the deflection yoke and magnet are in one body, untighten the screw for the body. 2. Receive the green raster pattern from the color bar generator. 3. Slide the deflection yoke until it touches the funnel side of the CRT. 4. Adjust center of screen to green, with red and blue on the sides, using the pair of purity magnets. 5. Switch the color bar generator from the green raster pattern to the crosshatch pattern. 6. Combine red and blue of the 3 color crosshatch pattern on the center of the screen by adjusting the pair of 4 pole magnets. 7. Combine red/blue (magenta) and green by adjusting the pair of 6 pole magnets. 8. Adjust the crosshatch pattern to change to white by repeating steps 6 and 7. 3-2: PURITY NOTE Adjust after performing adjustments in section 3-1. 1. Receive the green raster pattern from color bar generator. 2. Adjust the pair of purity magnets to center the color on the screen. Adjust the pair of purity magnets so the color at the ends are equally wide. 3. Move the deflection yoke backward (to neck side) slowly, and stop it at the position when the whole screen is green. 4. Confirm red and blue color. 5. Adjust the slant of the deflection yoke while watching the screen, then tighten the fixing screw. DEFLECTION YOKE DEFLECTION YOKE SCREW MAGNET SCREW 3-3: STATIC CONVERGENCE NOTE Adjust after performing adjustments in section 3-2. 1. Receive the crosshatch pattern from the color bar generator. 2. Combine red and blue of the 3 color crosshatch pattern on the center of the screen by adjusting the pair of 4 pole magnets. 3. Combine red/blue (magenta) and green by adjusting the pair of 6 pole magnets. 3-4: DYNAMIC CONVERGENCE NOTE Adjust after performing adjustments in section 3-3. 1. Adjust the differences around the screen by moving the deflection yoke upward/downward and right/left. (Refer to Fig. 3-2-a) 2. Insert three wedges between the deflection yoke and CRT funnel to fix the deflection yoke. (Refer to Fig. 3-2-b) RGB RGB
R G B UPWARD/DOWNWARD SLANT RIGHT/LEFT SLANT Fig. 3-2-a
R G B
WEDGE
WEDGE
WEDGE WEDGE POSITION Fig. 3-2-b
PURITY MAGNETS 6 POLE MAGNETS 4 POLE MAGNETS Fig. 3-1
D-3
ELECTRICAL ADJUSTMENTS
4. ELECTRICAL ADJUSTMENT PARTS LOCATION GUIDE (WIRING CONNECTION)
CRT PCB
CP806
03 B P8
0 R8 3
0 R8
TP022 TP023
C
7
FB401
CP 4 01
CP803A
TU001
01 J8
CP802B CP801
CD801
CR T DY
GND CRT
DEGAUSS COIL
CD501 AC IN
S501B CP802A S501A
L503 CP502 CD101B CD101A SPEAKER
MAIN PCB
D-4
BLOCK DIAGRAM
TU001 10 11 12 CH. DOWN IC1001 AN7511 VOL. DOWN 21 CH. UP 66 VOL. UP POWER 73 67 68 OS101 1 69 70 74 78 76 D106 Q105 SW
I/O IIC TIM INT PWM AD
13
17
20
34
2
6 SPEAKER SP1001
SOUND AMP IC 4 8 Q801
RGB Proc.2 OSD SW CONTRAST BRIGHTNESS
Chroma Proc. ACC/C-BPF APC/KILLER TINT/DEMO
ATT
RGB Proc.1 RGB MATRIX COLOR CONT
MCU CLK
RGB OUTPUT Stage DRIVE CUT OFF HV BLK
50 51 52
RED OUT Q802 GREEN OUT
Q607
H-CTL
Q803 BLUE OUT
OSD ROM RAM
Ver.Proc. Ver SYNC SEP Ver.COUNT DOWN V RAMP
Hor.Proc. SYNC SEPA/Hor. VCO Hor.COUNT DOWN AFC-1/H COINCIDENT AFC-2 H PHASE
46 45 Q402 H. DRIVE Q401
VCXO
J703 2 J702 2 56 58 57 27 26 37 38
H. OUTPUT 3
X601 3.579545MHz
16
9 G
7 R
Q505 P. FAIL
T502 16 8 13 6 4
MICON/CHROM IC IC101 OEC7091C
V-OUT IC IC401 LA78040N-E Q507 FEED BACK SW 5 6 MEMORY IC SDA SCL IC199 BR24L02F-WE2
DEGAUSS COIL L503
B Heater 4
V801
F
8
IC501 LTV-817M-VB
FEED BACK Q502 BUFFER Q501
PUMP UP AMP + 7 1 VCC 3 6 5 FB401 9 DY
D501~D504 RECTIFIER
POWER AMP
Q503 PROTECT DRV. L501 2 1 4
1 2 10 3 3
F S HV
F501
AC IN
E-1
E-2
PRINTED CIRCUIT BOARDS MAIN/CRT (INSERTED PARTS)
SOLDER SIDE
D408
D404 R429 CD803A W002 W003
C406 CP601 R403 C435 D410 GND AFC ABL
HEATER
CP803A 180V D405
D411
W008 W007 TU001 C434 C007 D001
R410 C403 C448_1 8V 12V
CP4
01
T401
25V
COL
+B
C002
D412 R408 W062 W011 R409 R401 W010 W072 R413 R405 R424 C414
C43
7
C401 W001
FB401
R421
R404
C440_1
C004
Q402
C44
3
L401 HS402 D512
R503 D506 HS501
R542 B503 D509
D409
R446 R448
H IC 4 01
S4
01
Q401 R427 D406
C511 R506 W827 Q501 R520 C510 C527
Q502
C446
R449 R417 R504 W009 R418 C516
D516
W004
R508
C51
B502 4
R510_1
47 R4
D513
C509 W804 R501
D508 T502
C417_1
C526
R509
W039 W037 R415 W015
W038 R422 W834
C422 C427 R416 C418 C521 W829 C517_1 D403
R514 IC501 D503
D502
C506 D501
W036
R002
L001_1
W050 W049 W048 W831 W046 R608 C601 W833 R604 C106 R602
R001
D504
W006
D505
R527_1 R445 Q603 R516 R528 Q503
C515 Q602 Q601 C617 C606 R505 Q505 W809 W035 W070 C507 W014 W817 W012 R603 D521 W025 Q606 W024 W065 W069 W064 R605 R119 R130 C519 R519 D514
R52 5
C508 D528
C503
CP502
D510 W005 TP401 C518
CMD009A
C502
W802
R6
W067
29
R523_1
R518 R507 D511_1 R513 R512 D507 C513
TH501_1
W019
CP503
17_ R5
1
D515
R515
R537_1 W034
L501
R502
W832
05
C447_1 W040 W073
R423
D522
TP 02 4
R8 03
D606 W059 W058 W057 W816 W054 C612 CD802A C614 CP802A Q607 W811
RISK
R8
X601
C103 C602 C605
W843
B 03 P8 C
C623
Q507
F501 FH502
W023
OF FIRE - REPLACE AS MARKED.
D602 C615_1 R601 W056 W018 C616 W017 C622 W053 C610 R606 W052 W051 C624_1 R621 W061 R614 R613 R615 C628 C630 W823 W828 W068 R607 W032 W031 W030 W028 R617 R611 R620
R804 TP022 Q802_1 Q801_1 R802
CP806
R538
3B 80 D C
W020
W071
C8
19
C634_1 W055
R8
IC1001
07
_1
C505
FH501
W033
C621 C620_1 C1003 D604 R1001 W803
S501B
01 J8
C809 R815 R811 C808 R813 R809 R816 C810 R814 CP802B CD802B
TP023 Q803_1
C1001
C1005
00 R5
S501A
CD501
R806
W045
W044
W043
D603 W066
Q105
C633 R616
W812 CP801_1 R121 OS101 D106_1 W807
W029
CCD004A
W027 W026
R112
R113 C123
CD101B
W808 C118 CD101A
R110
R109
W041 W042
J703 R704_2 W060
J702
SW101
SW102
SW103
SW104
SW105
R701
F-1
F-2
F-3
C501
CCD004A
R101
SOLDER SIDE
R1005 C1004 R419 R420 R1008 R1004
C001 R116
R1003 R143 R115 R004 R003
PRINTED CIRCUIT BOARDS MAIN (CHIP MOUNTED PARTS)
R126
R128
R107
R125 R127 R129 1 C102 R103 25 C105 C104 R102 C107 C108_1 C603 R104 C604 64
IC 10 1
R106 R124 C629 R105 R108 R627 C609 41
R618
C627 C626
R609 R610 C112 IC199_1 R702 C101 R703
CMD009A
F-4
A
IC199_1 BR24L02F-WE2
B
0 1 E0 2 E1 0 3 E2 0 4 VSS 0
C
D
E
F
G
H
MICON/CHROMA/TUNER SCHEMATIC DIAGRAM
(MAIN PCB)
8
50V 10 KA C633
8
MEMORY IC
MODE
VCC
SCL
SDA
8 4.9
7 0
6 4.8
5 R617 4.8
47K 1/4W
R621 2.2K 1/2W 220 1/4W
4.9 5.6 W808
5 H.CTL Q607 KTC3198 P.CON+5V
R618 P.CON+5V W828 22K W823
R620
H_CTL
3 H_SYNC
H_OUT
11E1-EIC ABCL
C118 H_CTL
FROM/TO DEFLECTION/CRT R608 CLAMP 1K 1/4W P.CON+B V_OUT GND
G.OUT
7
B.OUT
R.OUT
6.3V 100 KA C101 0.01 F AT+5V 100P CH R105 4.7K R124 10K R130 10K 1/4W 0 64 R119 22K 1/4W AFT R112 R113 R116 R115 2.2K 1/4W KEY1 2.2K 1/4W KEY2 2.2K 22K POWER_ON REMOCON 4.9 69 4.9 70 0 71 NC 4.9 NC AUDIO_MUTE R125 47K X-RAY IIC_OFF ON_TIMER 0 77 NC POWER_FAIL R129 47K 4.9 78 0 79 4.9 80 NC R127 1K 4.9 2.9 74 4.9 75 PWM AD 0 76 I/O 4.9 68 ROM RAM 4.9 67 4.9 65 2.4 66 63 0 62 0 61 0 60 C112 R109 10K 1/4W
R110 10K 1/4W
2
7
100 1/4W
100 1/4W
100 1/4W
R610
10K
C630 10K 1/4W 10V R609 120K 470 YK R611 C629 0.01 7 F R627 10K
D606
V_FEEDBACK F 63V 1 MKT F C627 C626 ABCL H_OUT X-RAY R.OUT G.OUT C623 50V 2.2 8.8 40 4.6 39 R607 100 1/4W 4 V_OUT POWER_FAIL R606 V_FEEDBACK UNREG+12V X-RAY GND C621 16V 47 YK AT+5V KA 8.5 11.3 UNREG+12V 7.9 B.OUT H_SYNC 8V REG Q606 KTC3203_Y FROM/TO TV POWER C624_1 0.01 0.01
SDA R106 1 CNVSS 2 XIN 3 XOUT 4 TEST1 5 VSS 6 MCU VCC 7 TEST0 8 FILT 9 HLT 10 VHOLD 11 CVIN 12 RESET IN 13 MCU RESET OUT 14 Y SW OUT 15 V/C GND 16 3.58 XTAL 17 C-APC 18 MCU5.7V REG OUT 19 NC 20 CVBS IN3 21 AUDIO IN3 22 V/C VCC 23 MCU TEST 24 CVBS IN2 25 AUDIO IN2 26 CVBS IN1 27 AUDIO IN1 28 5.7V REG OUT 29 C(Y/C) IN 41 NC 42 HVCO F/B 43 AFC FILTER 44 DEF GND 45 FBP IN 46 H OUT 47 DEF VCC 48 NC 49 HI VCC 50 R OUT 51 G OUT 52 B OUT 53 ACL 54 NC 55 PROTECT 56 SDA 57 H_CTL 58 SCL 59 NC 60 NC 61 NC 62 DEGAUSS_H 63 STANDBY_H 64 VOLUME 65 NC 66 AFT 67 KEY1 68 KEY2 69 POWER_ON 70 REMOCON 71 AV2 72 AV1 73 AUDIO_MUTE 74 X-RAY 75 IIC_OFF 76 ON_TIMER 77 SYNC 78 POWER FAIL W809 80 EXT_MUTE 79 NC AT+5V MICON/CHROMA IC IC101 OEC7091C 1 0 2 0 3 5.0 4 SCL 4.7K
1K 1/4W
R107
R108
100
100
R616
5
6
0 59
4.9 58
0.3 57
4.9 56
6
NC 0 4.6 NC 2.3 3.2 3.2 3.5 8.0 0 8.0 4.6 4.9 0 3.4 3.7 0 NC 55 54 53 52 51 50 49 48 47 46 45 44 43 42 41
50V 1 KA
R615
R614
R613
C628
6
MCU GND Ver.Proc. IIC BUS
DECODER
37 0 22K 1/4W 36 3.3 35 4.0
SDA/SCL OSD
PGB OUTPUT Stage DRIVE CUT-OFF HV BLK
Hor.Proc. SYNC SEPA/Hor.VCO Hor.COUNT DOWN AFC-1/H COINCIDENT AFC-2 H PHASE
Ver SYNC SEP Ver.COUNT DOWN V RAMP
4.5 38 2.6
C622 50V 1 KA AUDIO_OUT 1 D603 1SS133 P.CON+5V TUNER+5V 5V REG Q602 KTC3203_Y 5.5 C617 10V 100 YK VIDEO_IN 5.5 5V REG Q603 KTC3203_Y C620_1 0.01 B
72
33
5
73
32
IIC TIM INT CCD
P-ON CONT
Power Manage. MCU RESET
RGB Proc.2 OSD SW CONTRAST BRIGHTNESS
RGB Proc.1 RGB MATRIX COLOR CONT
34 4.6 NC 3.1 NC 8.8 2.0 NC 2.3 NC 5.7
5
D604 MTZJ8.2B FROM/TO SOUND/AV R605 220 1/2W AUDIO_MUTE VIDEO_IN AUDIO_IN 4.9 AUDIO_OUT P.CON+5V 7.2 R629 22 3W C001
19
29
CPU core
CLK CONT
MCU CLK
Vldeo Proc. C-TRAP/YDELAY SHARPNESS BLACK STRETCH Y MUTE
LPF 6bB AMP
Chroma Proc. ACC/C-BPF APC/KILLER TINT/DEMO
30
31
R604 C614 100 1/4W AUDIO_IN
ATT
28 2.3 27
GND
VCO XO VCXO
4
26
30 Y(Y/C) IN 31 VREG VCC 32 FSC OUT 33 MONITOR OUT 34 AUDIO ATT OUT 35 AUDIO ATT FILTER 36 TEST 3 37 V RAMP F/B 38 V RAMP OUT 39 V RAMP CAP 40 8.7V REG OUT
2.0 50V 1 KA C612 2.2 NC 50V 1 KA
7.2 4.9
4
25
18
NC
1
NC NC
5 5.0 0 C102 0.01 F
6 4.9 C104
7 0 0.01 F
8 1.2
9 2.0 C108_1
10 0.8 0.001 B
11 3.4
12 4.9
13 5.0 C602
14 3.4 F 0.1
15 0 X601
16 3.4
17 2.9 R602
C605 0.022 F 22P CH 100CT3R505 3.579545MHz
19 20 21 22 23 24 18 5.6 NC 0 2.9 2.8 5.0 0 NC 2.0 100 1/4W C615_1 TU_VIDEO 10V 100 YK 50V 1 Serr D602
0.01 F C002 6.3V 1000 YK L001_1 3.3uH TUNER+5V
NC 2 TUNER+5V 3 NC 4 NC 5
C107 50V 1 KA
C106
C105 1K
50V 1 KA
NC NC NC
W833
R102
C601
B
R103 470P B
C603
220P
C606
16V 47 YK
C103
C609 0.01 F C616
MTZJ9.1B NC TU_AUDIO 50V 1 KA 6
R104
1M
C604
1K
3
W816
8.2K 50V 1 KA 1/4W
C610 6.3V 47 KA C634_1 0.027 B
3
NC 7 NC 8 NC 9 SCL 10 NC NC NC R004 SCL SDA NC AFT IIC_OFF TU_AUDIO 0.022 B C007 NC SDA SCL R002 R001 NC IIC_OFF SDA SCL GND P.CON+B TEST POINT CP601 A2001WR2-6P 6 5 4 3 2 1
0 4.8 SWITCHING Q105 KRA102MAT
ON_TIMER
REMOCON
POWER_ON
KEY2
KEY1
AT+5V
R601
5.1
R003 100 SDA 11 100 AFT 12
1/4W
R143 47
25V 10 KA
R121
TU_AUDIO 13
270
2
R128
560 5V REG 5.5 Q601 KTC3203_Y 8.8 R603 120 1/2W
NC 14 P.CON+B 15 NC 16 TU001 115-V-KA35ARB TU_VIDEO 17
20 21
2
C123
POWER ON/ON TIMER D106_1
SLR-342VCT32
SW101 EVQ21505R CH DOWN
SW103 EVQ21505R
VOL DOWN
SW102 EVQ21505R
SW104 EVQ21505R
SW105 EVQ21505R
0.022
2.7K 4.9 4.8 0 VOL UP CH UP B+ 3 GND 2 1
560 POWER
NC
C004
F
R126
R101
4.9
15K 1/2W 15K 1/2W
TU_VIDEO MTZJ33B
Vout
D001
PCB010 CMD009
OS101 RPM7138-WH5
CAUTION: DIGITAL TRANSISTOR NOTE:THE DC VOLTAGE AT EACH PART WAS MEASURED WITH THE DIGITAL TESTER WHEN THE COLOR BROADCAST WAS RECEIVED IN GOOD CONDITION AND PICTURE IS NORMAL.
1
NOTE: THIS SCHEMATIC DIAGRAM IS THE LATEST AT THE TIME OF PRINTING AND SUBJECT TO CHANGE WITHOUT NOTICE
CAUTION:SINCE THESE PARTS MARKED BY CRITICAL FOR SAFETY,USE ONES
DESCRIBED IN PARTS LIST ONLY
ARE
ATTENTION
:LES PIECES REPAREES PAR UN ETANT DANGEREUSES AN POINT DE VUE SECURITE N'UTILISER QUE CELLS DECRITES DANS LA NOMENCLATURE DES PIECES
R.SIGNAL G.SIGNAL B.SIGNAL DEFLECTION SIGNAL TUNER VIDEO SIGNAL
G H
1
A
B
C
D
E
F
G-1
G-2
A
B
C
D
E
F
G
H
TV POWER SCHEMATIC DIAGRAM
(MAIN PCB)
8
PROTECTION AGAINST FIRE HAZARD, CAUTION :FOR CONTINUEDWITH THE SAME TYPE 4A 125V (F501) REPLACE ONLY FUSE.
4A 125V
8
PROTECTION CONTINUE LES ATTENTION :POUR UNEN'UTILISER QUE DES FUSIBLE RISQUES D'INCEIE DE MEME TYPE 4A 125V (F501).
TO SOUND/AV GND D505 R517_1 SOUND+B C518 500V 470P B C519 16V 1000 YK 21DQ09N 3.3 1W
7
7
SOUND_GND FROM/TO DEFLECTION/CRT D510 DEGAUSS COIL L503 8R200030 1 W802 R501 TH501_1 1 B59203-S1060-B14 1N4005-EIC CP503 003P-2100 D501 3.3 5W C 0.22 1W R514 C521 2 2KV 820P RR 1 2.7M 1/2W +-10% +B RU2AM-EIC PROTECT DRIVE Q503 2SA1624 135.0 0 100V 10 MHE 135.0 R527_1 5.6K UNREG+12V W834 P.CON+B R500
CP502 A1561WV2-2P
6
160V 100 MHE
C517_1
2
6
R523_1 47K
1N4005-EIC
D502
C507
200V 330 UP
2.2M 1/2W
R525 1.2 2W GND 1/4W
C526
275V 0.22 ECQUL
1.5M 1/2W
1N4005-EIC
B
500V 0.001
MTZJ18B
C505
R538
D504
C502
0.0056 B
C527
6.8K
5
F501 51MS040L 4A125V
D509
3 1
4 2
T502 8129109S
R528
4A 125V
500V 0.001
1N4005-EIC
D503
C503
B
R510_1
FROM/TO MICON/CHROMA/TUNER W832 R537_1 P.FAIL Q505 KTA1266 X-RAY 10K 1/4W POWER_FAIL
5
50V 10 YK
NC 144.0
R516
7 6
12 13 14 15 16 132.3 0 0 11.3 W829 D513 21DQ09N 16V 2200 YK C515
C516
0
1/4W
FH501 EYF-52BCY
4A125V
FH502 EYF-52BCY
COIL,LINE FILTER L501 1R0A562F20
1.7
8
11
10.0
D516 1N4937
R504 100 1/4W
D521 MTZJ6.8B
R505 1K 1/4W
4.9 4.8
0
10K
UNREG+12V AT+5V
W804
W5RH3.5X5X1.0
AC120V_60Hz CD501 09414909
NC 5 10.3 6.6 10.3 R508 G 4.8 POWER AMP Q501 2SK3563(ORION_Q) W5RH3.5X5X1.0 220 1W 1SS133 C509 W827 0.047 M 56K 1/4W D512 4 3 2
S501A B502
4
BLADE WIDE
BLACK C514 WHITE S501B C506 250V 0.001 KX R
GND
4
2KV 680P
144.0 D S 0.1
17 NC 18 NC 1SS133 MTZJ2.2B D515 D507
1SS133
D508
B503
C511 50V 1 KA MTZJ18B D506
R506
1K
R509
3
100 1/4W
1/4W
100 1/4W
R520
R503
BUFFER Q502 KTC3198 4.8 0.1
3
1/2W 120K
100 1/4W
R502
0.47 1W
0.0082 B
R542
C513
0
C508 250V 0.0047 KX
C501
HS501 763WSAA021
9.5 C510 MTZJ3.9B D511_1 1/4W 0.033 B FEED BACK IC501 5.5 R513
6.0 1SS133 FEED BACK SWITCHING Q507 KTC3198 1SS133 D514 D522
2
2.2K
0.1
R515
F
LTV-817M-VB
4
1
11.5
10.5
R512 680 1/4W
R519 100 1/4W 1.2K 1/4W R507
2
3
0.1
2 9.5 MTZJ5.6B D528
5.6K +-1%
R518
PCB010 CMD009
1
NOTE: THIS SCHEMATIC DIAGRAM IS THE LATEST AT THE TIME OF PRINTING AND SUBJECT TO CHANGE WITHOUT NOTICE
NOTE:THE DC VOLTAGE AT EACH PART WAS MEASURED WITH THE DIGITAL TESTER WHEN THE COLOR BROADCAST WAS RECEIVED IN GOOD CONDITION AND PICTURE IS NORMAL.
CAUTION:SINCE THESE PARTS MARKED BY CRITICAL FOR SAFETY,USE ONES
DESCRIBED IN PARTS LIST ONLY
ARE
ETANT ATTENTION:LES PIECES REPAREES PAR UN SECURITE DANGEREUSES AN POINT DE VUE N'UTILISER QUE CELLS DECRITES DANS LA NOMENCLATURE DES PIECES
1
NOTE: THE RESISTOR MARKED F IS FUSE RESISTOR. THE ALUMI ELECTROLYTIC CAPACITOR MARKED NP IS NON POLAR ONE. A B
C
D
E
F
G
H
G-3
G-4
A
FROM MICON/CHROMA/TUNER CLAMP
B
C
D
E
F
CP802B B2013H02-5P 1 2 3 4 5 1 2 3 4 5 1 2 3 4 GND CLAMP G.OUT R.OUT B.OUT CP803B GND CLAMP G.OUT R.OUT B.OUT
G
H
DEFLECTION/CRT SCHEMATIC DIAGRAM
V-OUT IC IC401 LA78040N-E
THERMAL PROTECTION PUMP UP AMP
(MAIN PCB)
CP802A B2013H02-5P GND CLAMP G.OUT R.OUT B.OUT GND CLAMP G.OUT R.OUT B.OUT
8
G.OUT R.OUT B.OUT
8
CP803A B2013H02-4P HEATER 1 HEATER GND 2 GND NC 180V 7 25.0 3.5 NC 180V 3 4
B2013H02-4P HEATER HEATER GND GND NC 180V NC 180V 4.7K 1/4W 4.7K 1/4W 4.7K 1/4W R809 R811 R814
1 3.5
2 25.0 C414
3 2.0 35V 100 YK
4 0
5 12.0
6
7
W843
8
R423 12 100 1/4W R424 6.8K 1/4W R418 R419 680 15K 1/4W 50V 10 YK 33K 1/4W D403 13 11E1-EIC 330 1/2W
CD801 CH823004 V801 A48LGS30X14AN35 9 10 8 6 11
50V 10 YK
CP801_1 A2361WV2-2P 1 2 1 2
RED OUT Q801_1 KTC4217
3.2 100.6 2.7
330 1/4W 390P B R813
GREEN OUT Q802_1 KTC4217 3.2
BLUE OUT Q803_1 KTC4217 3.2
7
100V 0.15 MKT
98.4 2.7
330 1/4W 390P B R815 C809
95.4 2.7
390P B 330 1/4W C810 R816
C422
R420
25V 470 YK
R410
R417
C418
1 1/2W
C417_1
R416
1.8K
1/2W C427
5 7 1
6
R422
HS401 763WSAA021
1.8 1/2W
2.2K 1/2W
R413
TO DY
C808
4.7K
R415
R G B
6
5 4 CP401 A1561WV2-A5P 3 14 15 16
100V 22 YK
TP022
TP024
TP023
C434
R429 3.9 D411
AU02A-EIC 1W
NC
2 1
470 YK
12K 2W
1/4W
2.7K 1/4W
16V
4.7K
R805
2.7K
R802
R807
FROM/TO MICON//CHROMA/TUNER
5
X-RAY P.CON+B
W831 27K
R401 +-1%
R409 27K +-1%
R803
R806
R804
2.7K 1/4W
+-1%
MTZJ5.1B
C447_1
12K 2W
12K 2W
D412
R408
5
C401 9 T401 ETH09K14BZ
250V 0.33 PMS
470 1/2W
R446
GND V_FEEDBACK
4
V_OUT ABCL H_OUT
50V 22 YK
H.DRIVE Q402 2SC1627_Y 27.0
C437
NC 2 1
6 10 11
68 1/2W
R404
4.7mH
L401
3
4
250V 2.2
MHE
4
FB401 130.0 1 COL FQI20B103_M HV FOCUS CP806 132.5 132.5 48.0 7.0 2KV 0.001 B 6 2 VIDEO B+ F S GND 0 11 ABL 7 4.3 8 9 FOCUS SCREEN SCREEN C819_1
1/4W
H_SYNC R405
0
C440_1
500V 0.0012
130.0
100 1/4W
1K
0 0
FROM/TO TV POWER GND
R427
H.OUTPUT Q401 2SC5885
TP401 +B W817
HS402 763WSAA028
1.25KV 0.0066 MPP
0.3
B
C446
C443
AFC 9 HEA 10 TER 8 GND
96.4
22K 1/4W P.CON+B C406 500V 100P B
NC 4 E12 25.0 E25 3
GND 0 8 E8 5 NC
101.6 0
4 3 6 5
7
3
R403
0
3
F 1 0 99.6
J801 ISMS01S
0
6.4
MTZJ6.2B D404 R447 UNREG+12V 150 2W 11E1-EIC AU02A-EIC D406
PCB110 CCD004
D405
11E1-EIC
D409
D410
2
AU02A-EIC
2
NOTE: THIS SCHEMATIC DIAGRAM IS THE LATEST AT THE TIME OF PRINTING AND SUBJECT TO CHANGE WITHOUT NOTICE
R449 680 R448 680 1/2W 35V 470 YK 250V 22 YK 1/2W
NOTE:THE DC VOLTAGE AT EACH PART WAS MEASURED WITH THE DIGITAL TESTER WHEN THE COLOR BROADCAST WAS RECEIVED IN GOOD CONDITION AND PICTURE IS NORMAL.
R445
100V 0.1 MHE 220K 1/4W
NOTE: THE RESISTOR MARKED F IS FUSE RESISTOR. THE ALUMI ELECTROLYTIC CAPACITOR MARKED NP IS NON POLAR ONE.
C448_1
150K
1/4W C435
ETANT ATTENTION:LES PIECES REPAREES PAR UN SECURITE DANGEREUSES AN POINT DE VUE
11E1-EIC D408 R421
R.SIGNAL G.SIGNAL B.SIGNAL DEFLECTION SIGNAL
G H 1
1
N'UTILISER QUE CELLS DECRITES DANS LA NOMENCLATURE DES PIECES
PCB010 CMD009
C403
CAUTION:SINCE THESE PARTS MARKED BY CRITICAL FOR SAFETY,USE ONES
DESCRIBED IN PARTS LIST ONLY
ARE
A
B
C
D
E
F
G-5
G-6
A
B
C
D
E
F
G
H
SOUND/AV SCHEMATIC DIAGRAM
8
(MAIN PCB)
8
ACCESSORY RCA JACK WHITE J703 AV1-09AD-4 (FRONT) H 2 1 AUDIO 2 20 VIDEO_IN VIDEO 2 68 1/4W R702 R701 47K W811 E 19 R703 820 H E R704_2 10 1/4W RCA JACK YELLOW J702 AV1-09AD-3 2 1 V_IN TM101 RC-EH050(CT-859) UM-4 BT002 GR03X-SP2 A_IN
TO MICON/CHROMA/TUNER
7
AUDIO_IN
UM-4 BT001 GR03X-SP2
7
GND
6
6
5
5
W807
4
FROM TV POWER 18
W812
4
SOUND_GND SOUND+B
CD101A C3013207
SPEAKER 1 2 1 2 SP1001 S08F21A 8 OHM
CD101B C3013206 GND 5 6 7 8 SOUND AMP IC AN7511 8.2 3.5 0 3.4
+
3
FROM MICON/CHROMA/TUNER 4 R1001 AUDIO_MUTE 47K 1/4W 5.1 3 0 2 0.3
-
3
1 3.9
R1003 P.CON+5V 68K 25V 10 KA KA
R1004
C1003
R1005
W803
C1004
50V
2
C1005
100K
270K
1
B
IC1001
2
GND R1008 39K
C1001 AUDIO_OUT 50V 0.1 KA
17
0.0015
PCB010 CMD009
1
NOTE: THIS SCHEMATIC DIAGRAM IS THE LATEST AT THE TIME OF PRINTING AND SUBJECT TO CHANGE WITHOUT NOTICE
NOTE:THE DC VOLTAGE AT EACH PART WAS MEASURED WITH THE DIGITAL TESTER WHEN THE COLOR BROADCAST WAS RECEIVED IN GOOD CONDITION AND PICTURE IS NORMAL.
ETANT ATTENTION:LES PIECES REPAREES PAR UN SECURITE DANGEREUSES AN POINT DE VUE N'UTILISER QUE CELLS DECRITES DANS LA NOMENCLATURE DES PIECES
CAUTION:SINCE THESE PARTS MARKED BY CRITICAL FOR SAFETY,USE ONES
DESCRIBED IN PARTS LIST ONLY
ARE
TUNER VIDEO SIGNAL AUDIO SIGNAL
1
A
B
C
D
E
F
G
H
G-7
G-8
MICON/CHROMA/TUNER
WAVEFORMS
1 0.5V 2ms/div
6 1V 20µs/div
11 200V 20µs/div
2
20V 20µs/div
7 1V 20µs/div
12 10V 5ms/div
DEFLECTION/CRT
3 200mV 20µs/div
8 0.5V 5ms/div
13 10V 5ms/div
4
0.5V 5ms/div
9
20V 20µs/div
14 50V 20µs/div
5
1V 20µs/div
10 2V 20µs/div
15 50V 20µs/div
NOTE: The following waveforms were measured at the point of the corresponding balloon number in the schematic diagram.
H-1
WAVEFORMS
16 50V 20µs/div
SOUND/AV
17 0.5V 1ms/div
18 1V 1ms/div
19 200mV 500µs/div
20 500mV 20µs/div
NOTE: The following waveforms were measured at the point of the corresponding balloon number in the schematic diagram.
H-2
MECHANICAL EXPLODED VIEW
202
103
202 102B 202
117
201
102A
102B
119
102
119
201 106 105
201
202
PCB110 (CRT PCB ASS'Y)
107
119
205 201
119
205 203
PCB010 (MAIN PCB ASS'Y) 204 101D 101B 118 104 101C
101A
101 I-1
MECHANICAL EXPLODED VIEW (PACKING DIAGRAM)
109
113, 114, 115, TM101
109
109
109
108
111
116
110
110
I-2
MECHANICAL REPLACEMENT PARTS LIST
Location No. TSB P/N
101 101A 101B 101C 101D 102 102A 102B 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 201 202 203 204 205 AE006004 AE006173 AE001500 AD300694 AE006174 AE005646 AE006175 AE005648 AE005649 AE005650 AE005651 BZ710660 BZ710260 AE005652 AD300700 AD300701 AE005653 AE005654 AE005715 AE006176 AE006177 AE005656 AE005657 AE006178 AD302158 AE005928 AE004847 AE003531 AE003528 AE005659
Reference No.
7A701A356A 701WPJC966 713WPAA046 713WPAA050 735WPBB357 7A702A088A 702WPAA844 800WQ0A091 722549A413 723000C727 723000C778 741WUA0021 899HV3T000 791WHAA126 792WHAA054 792WHAA055 793WCDC582 A3M218S975 JB5KD200 J3M21802A J3M21821B 723000C776 726000A085 735WPAA938 800WR0A002 8160H50B8U 8117540A6U 810763080U 8110630A0U 8109I3080U FRONT CABI ASS'Y CABINET,FRONT GLASS,LED GUIDE,REMOCON BUTTON,FRAME BACK CABI ASS'Y CABINET,BACK FELT SHEET
Description
SHEET,RATING SHEET,CAUTION FILM,DECORATION SPRING,EARTH HOLDER,ANODE WIRE FILM BAG PACKAGE,TOP PACKAGE,BOTTOM GIFT BOX INSTRUCTION BOOK KIT POLYBAG,INSTRUCTION(RED CAUTION) GUARANTEE CARD INSTRUCTION BOOK(E/S) SHEET,BAR CODE SHEET,CRT SERVICEMAN HOLDER,SPEAKER SHEET,CRT SUPPORT SCREW,TAP TITE(P) SCREW,TAP TITE(B0) TRUSS SCREW,TAP TITE(S) BRAZIER SCREW,TAP TITE(P) BRAZIER SCREW,TAP TITE(B) WH7 W5x28 4x16 3x8 3x10 3x8
J1-1
ELECTRICAL REPLACEMENT PARTS LIST
Location No. TSB P/N
! ! ! ! ! ! ! ! ! R401 R404 R408 R409 R429 R447 R500 R501 R508 R509 R510 R514 R515 R517 R518 R519 R525 R538 R542 R629 R803 R805 R807 BZ210089 AE001556 BZ210258 BZ210089 AE005886 BZ210229 BZ210080 AD300652 BZ210240 AD301203 AE003279 AE005735 BZ210081 AE001696 BZ210244 BZ210124 AD301315 BZ210206 BZ210251 AE000081 BZ210050 BZ210050 BZ210050 BZ110149 AD301434 BZ110041 BZ110195 BZ110174 AE001548 BZ110205 BZ110204 BZ110061 BZ110025 AD301026 AE002878 BZ110172 BZ110135 BZ110203 BZ110207 BZ110092 AD301635 79091377 AE003280 BZ110247 BZ410037 BZ410054 BZ410043 BZ410066 BZ410063 BZ410043 BZ410043 BZ410043 BZ410063 BZ410063 BZ410020 BZ410085 BZ410085 BZ410085 BZ410085 BZ410010 AD300671 BZ410067 BZ410006 AD300671 BZ410080 BZ410006 BZ410006 BZ410010 BZ410006
Reference No. RESISTORS
R4X5T6273F R615U2680J R4X5T6472F R4X5T6273F R638813R9J R3X28A151J R0G3K2275K R5X2CD3R3J R3X181221J R002T4101J R00202225J R63881R22J R002T2124J R3X1813R3J R4X5T6562F R002T4122J R3X18A1R2J R002T2155J R3X181R47J R3X28B220J R3X18A123J R3X18A123J R3X18A123J E02LT4471M E02LU4101M E02LT3471M E02LU8220M P4J7F3334J P4N8FJ662H E02LU5220M E0ELFD220M C0JTB0513K P2122B224M CD39E0M13M CD39E0MQ3M C03L0R7U2K E02L02222M C0PLRR7W2K E02LT2102M E5EZFB101M E51CGC331M CQGTB04S3K E52H05010M C0JBB0713K D97U03301B 0021721150 D2WT011E10 D97U06R21B D2WTAU02A0 D2WT011E10 D2WT011E10 D2WT011E10 D2WTAU02A0 D2WTAU02A0 D97U05R11B D2WXN40050 D2WXN40050 D2WXN40050 D2WXN40050 D28T21DQN9 D97U01801B D97U02R21B D1VT001330 D97U01801B D2WXRU2AM0 D1VT001330 D1VT001330 D28T21DQN9 D1VT001330 R,METAL R,FUSE R,METAL R,METAL R,FUSE R,METAL OXIDE RC R,CEMENT R,METAL OXIDE RC RC R,FUSE RC R,METAL OXIDE R,METAL RC R,METAL OXIDE RC R,METAL OXIDE R,METAL OXIDE R,METAL OXIDE R,METAL OXIDE R,METAL OXIDE CE CE CE CE CMPP CMPP CE CE CC CMP CC CC CC CE CC CE CE CE CC CE CC
Description
27K OHM 1/6W 68 OHM 1/2W 4.7K OHM 1/6W 27K OHM 1/6W 3.9 OHM 1W 150 OHM 2W 2.7M OHM 1/2W 3.3 OHM 5W 220 OHM 1W 100 OHM 1/4W 2.2M OHM 1/2W 0.22 OHM 1W 120K OHM 1/2W 3.3 OHM 1W 5.6K OHM 1/6W 1.2K OHM 1/4W 1.2 OHM 2W 1.5M OHM 1/2W 0.47 OHM 1W 22 OHM 3W 12K OHM 2W 12K OHM 2W 12K OHM 2W 470 UF 35V 100 UF 35V 470 UF 25V 22 UF 100V 0.33 UF 250V PMS 0.0066UF 1.25KV 22 UF 50V 22 UF 250V 0.001 UF 500V B 0.22 UF 275V ECQUL 0.001 UF 250V 0.0047UF 250V 680 PF 2KV R 2200 UF 16V 820 PF 2KV RR 1000 UF 16V 100 UF 160V 330 UF 200V 0.0056UF 50V B 1 UF 50V 0.001 UF 2KV B MTZJ33B T-77 SLR-342VCT32 11E1-EIC MTZJ6.2B T-77 AU02A-EIC 11E1-EIC 11E1-EIC 11E1-EIC AU02A-EIC AU02A-EIC MTZJ5.1B T-77 1N4005-EIC 1N4005-EIC 1N4005-EIC 1N4005-EIC 21DQ09N-TA2B1 MTZJ18B T-77 MTZJ2.2B T-77 1SS133T-77 MTZJ18B T-77 RU2AM-EIC 1SS133T-77 1SS133T-77 21DQ09N-TA2B1 1SS133T-77
! ! ! ! ! ! ! ! ! ! !
CAPACITORS
! C403 C414 ! C418 ! C434 C437 ! C443 C446 ! C448 C503 ! C505 ! C506 ! C508 C514 ! C515 ! C517 ! C519 ! C521 ! C526 C527 C615 C819 D001 D106 D403 D404 D405 D406 D408 D409 D410 D411 D412 D501 D502 D503 D504 D505 D506 D507 D508 D509 D510 D511 D512 D513 D514
DIODES
DIODE,ZENER LED DIODE,SILICON DIODE,ZENER DIODE,SILICON DIODE,SILICON DIODE,SILICON DIODE,SILICON DIODE,SILICON DIODE,SILICON DIODE,ZENER DIODE,SILICON DIODE,SILICON DIODE,SILICON DIODE,SILICON DIODE,SCHOTTKY DIODE,ZENER DIODE,ZENER DIODE,SILICON DIODE,ZENER DIODE,SILICON DIODE,SILICON DIODE,SILICON DIODE,SCHOTTKY DIODE,SILICON
! !
! ! ! ! ! ! ! !
! ! ! !
J2-1
ELECTRICAL REPLACEMENT PARTS LIST
Location No. TSB P/N
D515 D516 D521 D522 D528 D602 D603 D604 D606 IC101 IC199 ! IC401 ! IC501 ! IC1001 Q105 Q401 Q402 Q501 Q502 Q503 Q505 Q507 Q601 Q602 Q603 Q606 Q607 Q801 Q802 Q803 BZ410006 AD300731 BZ410022 BZ410006 BZ410021 BZ410023 BZ410006 BZ410058 BZ410043 AE005644 AE005642 AE002783 BZ410088 BZ611001 BZ510086 AE000656 BZ510089 AE002251 BZ510069 BZ510004 BZ510073 BZ510069 BZ510070 BZ510070 BZ510070 BZ510070 BZ510069 BZ510091 BZ510091 BZ510091 BZ310136 AD301644 AD301395 AE001529 BZ310157 AE001531 AE005633 AE005632 BZ614434 BZ612010 BZ612010 BZ612010 BZ612010 BZ612010 AE005641 AE005643 BZ310121 BZ310121 AE005640 AE005640 AE005639 AE005637 BZ614310 BZ614493 BZ614303 BZ614283 BZ614016 AE005634 BZ614269 AE005636 AE005635 BZ614276 BZ614276 BZ614334
Reference No. DIODES
D1VT001330 D2WXN49370 D97U06R81B D1VT001330 D97U05R61B D97U09R11B D1VT001330 D97U08R21B D2WT011E10 I56F07091C A3M218S015 I03TD804N0 0002E00610 I01DP75110 TPATB03003 TC1G058850 TC5T01627Y T25F035630 TCATC31980 TA3T016240 TAATA12660 TCATC31980 TCAT032034 TCAT032034 TCAT032034 TCAT032034 TCATC31980 TCA0042170 TCA0042170 TCA0042170 021LA63R3K 021L75472J 029T000104 028R200030 045009003J 048129109S 060Q401112 060Q401111 066F120018 0504101T34 0504101T34 0504101T34 0504101T34 0504101T34 A3M218S010 A3M218S110 024HT03553 024HT03553 141R004016 141R004016 1209414909 06CH823004 WCL6844038 WBL6032038 069S450089 069S420110 069W01001A 069S260639 069S320010 06C3013207 06C3013206 067U005049 067U005049 067U004029 DIODE,SILICON DIODE,SILICON DIODE,ZENER DIODE,SILICON DIODE,ZENER DIODE,ZENER DIODE,SILICON DIODE,ZENER DIODE,SILICON
Description
1SS133T-77 1N4937 MTZJ6.8B T-77 1SS133T-77 MTZJ5.6B T-77 MTZJ9.1B T-77 1SS133T-77 MTZJ8.2B T-77 11E1-EIC OEC7091C BR24L02F-WE2 LA78040N-E LTV-817M-VB
ICS
IC INIT DATA IC PHOTO COUPLER IC COMPOUND TRANSISTOR TRANSISTOR,SILICON TRANSISTOR,SILICON FET TRANSISTOR,SILICON TRANSISTOR,SILICON TRANSISTOR,SILICON TRANSISTOR,SILICON TRANSISTOR,SILICON TRANSISTOR,SILICON TRANSISTOR,SILICON TRANSISTOR,SILICON TRANSISTOR,SILICON TRANSISTOR,SILICON TRANSISTOR,SILICON TRANSISTOR,SILICON COIL COIL COIL,LINE FILTER COIL,DEGAUSS TRANS,HORIZONTAL DRIVE TRANSFORMER,SWITCHING
TRANSISTORS
! ! ! ! ! KRA102MAT 2SC5885 2SC1627_Y(TPE2) 2SK3563(ORION_Q) KTC3198-AT(Y,GR) 2SA1624-AA KTA1266-AT(Y,GR) KTC3198-AT(Y,GR) KTC3203_Y-AT KTC3203_Y-AT KTC3203_Y-AT KTC3203_Y-AT KTC3198-AT(Y,GR) KTC4217(O,Y) KTC4217(O,Y) KTC4217(O,Y) 3.3 UH 4.7 MH 1R0A562F20 8R200030 ETH09K14BZ 8129109S
! ! !
COILS &TRANSFORMERS
L001 L401 ! L501 ! L503 T401 ! T502 J702 J703 ! J801 SW101 SW102 SW103 SW104 SW105 PCB010 PCB110 B502 B503 BT001 BT002 ! CD501 CD801 CD802 CD803 ! CP401 ! CP502 CP503 CP601 CP801 CD101A CD101B CP802A CP802B CP803A
JACKS
RCA JACK AV1-09AD-3 RCA JACK AV1-09AD-4 SOCKET,CATHODE RAY TUBE ISMS01S
SWITCHES
SWITCH,TACT SWITCH,TACT SWITCH,TACT SWITCH,TACT SWITCH,TACT PCB ASS'Y PCB ASS'Y CORE,BEADS CORE,BEADS BATTERY,MANGAN BATTERY,MANGAN CORD,AC BUSH CORD,CONNECTOR FLAT CABLE AWM2468 A FLAT CABLE AWM2468 A CONNECTOR PCB SIDE CONNECTOR PCB SIDE CONNECTOR PCB SIDE CONNECTOR PCB SIDE CONNECTOR PCB SIDE CORD,CONNECTOR CORD,CONNECTOR WIRE HOLDER WIRE HOLDER WIRE HOLDER EVQ21505R EVQ21505R EVQ21505R EVQ21505R EVQ21505R CMD009A CCD004A W5RH3.5X5X1.0 W5RH3.5X5X1.0 GR03X-SP2 GR03X-SP2 9414909 CH823004 WG26 5C GRAY 440MM WG26 4C BLACK 320MM A1561WV2-A5P A1561WV2-2P 003P-2100 A2001WR2-6P A2361WV2-2P C3013207 C3013206 B2013H02-5P B2013H02-5P B2013H02-4P
P.C.BOARD ASSEMBLIES MISCELLANEOUS
J2-2
ELECTRICAL REPLACEMENT PARTS LIST
Location No. TSB P/N
CP803B EL001 EL002 F501 FB401 FH501 FH502 OS101 SP1001 TH501 TM101 TU001 V801 X601 BZ614334 BZ614043 BZ614044 AD302166 AE003283 AE002634 AE002634 AD301048 AE005722 AD302000 AD301335 AE006069 AE005638 BZ613004
Reference No. MISCELLANEOUS
067U004029 124116281A 124120301A 081PC04005 043220061F 06710T0009 06710T0009 0773071001 070Y132027 D8EE0B1400 076N0EH020 0163300018 098Y200495 100CT3R505
Description
B2013H02-4P XRY16X28BD XRY20X30BD 51MS040L FQI20B103_M EYF-52BCY EYF-52BCY RPM7138-WH5 S08F21A B59203-S1060-B14 RC-EH020 115-V-KA35ARB A48LGS30X14AN35 HC-49/U
! !
! ! ! !
WIRE HOLDER EYE LET EYE LET FUSE TRANSFORMER,FLYBACK HOLDER,FUSE HOLDER,FUSE REMOTE RECEIVER SPEAKER DEGAUSS ELEMENT TRANSMITTER RF UNIT CRT W/DY CRYSTAL
RESISTOR RC................... CAPACITORS CC................... CE................... CP................... CPP.................. CPL.................. CMP...................... CMPL................ CMPP................ CERAMIC CAPACITOR ALUMI ELECTROLYTIC CAPACITOR POLYESTER CAPACITOR POLYPROPYLENE CAPACITOR PLASTIC CAPACITOR METAL POLYESTER CAPACITOR METAL PLASTIC CAPACITOR METAL POLYPROPYLENE CAPACITOR CARBON RESISTOR
J2-3
TOSHIBA CORPORATION
1-1, SHIBAURA 1-CHOME, MINATO-KU, TOKYO 105-8001, JAPAN