Text preview for : China ch. 29M03 with M37160, M61260.pdf part of China tv Service Manual
Back to : China ch. 29M03 with M37 | Home
.
SERVICE MANUAL
CHASSIS : Mitsubishi
DOCUMENT : SM-20PM
DATE : 08/08/2005
This manual is the latest at the time of print, and does not include the modification which
may be made after the printing, by the constant improvement of product.
.
CONTENTS
1. Safety precautions.....................................................................................................1
2. Service adjustment.....................................................................................................2
3. Purity / convergence adjustment................................................................................8
4. List of Parts ..............................................................................................................10
5. Circuit Diagram.......................................................................................Attached
.
1. SAFETY PRECAUTIONS
1. The design of this product contains special hardware, many those components that indicate evidence of overheating should
circuits and components especially for safety purposes. For be replaced. Always use the manufacturer's replacement
continued protection, no changes should be made to the original components.
design unless authorized in writing by the manufacturer. 9. Isolation Check
Replacement parts must be identical to those used in the (Safety for Electrical Shock Hazard)
original circuits. Service should be performed by qualified After re-assembling the product, always perform an isolation
personnel only. check on the exposed metal parts of the cabinet (antenna
terminals, video/audio input and output terminals, Control knobs,
2. Alterations of the design or circuitry of the products should not metal cabinet, screw heads, earphone jack, control shafts, etc.)
be made. Any design alterations or additions will void the to be sure the product is safe to operate without danger of
manufacturer's warranty and will further relieve the electrical shock.
manufacturer of responsibility for personal injury or property 10. The surface of the TV screen is coated with a thin film which can
damage resulting therefrom. easily be damaged. Be very careful with it when handle the TV.
Should the TV screen become soiled, wipe it with a soft dry
3. Many electrical and mechanical parts in the products have cloth. Never rub it forcefully. Never use any cleaner or detergent
special safety-related characteristics. These characteristics are on it.
often not evident from visual inspection nor can the protection
afforded by them necessarily be obtained by using replacement (1) Dielectric Strength Test
components rated for higher voltage, wattage, etc. The isolation between the AC primary circuit and all metal parts
Replacement parts which have these special safety exposed to the user, particularly any exposed metal part having
characteristics are identified in the parts list of Service manual. a return path to the chassis should withstand a voltage of 3000V
Electrical components having such features are identified by AC (r.m.s.) for a period of one second.
shading on the schematics and by ( ) on the parts list in (...Withstand a voltage of 1100V AC (r.m.s.) to an appliance
Service manual. The use of a substitute replacement which rated up to 120V, and 3000V AC (r.m.s.) to an appliance rated
does not have the same safety characteristics as the 200V or more, for a period of one second.)
recommended replacement part shown in the parts list of This method of test requires test equipment not generally found
Service manual may cause shock, fire, or other hazards in the service trade.
(2) Leakage Current Check
4. Don't short between the LIVE side ground and ISOLATED Plug the AC line cord directly into the AC outlet (do not use line
(NEUTRAL) side ground or EARTH side ground when isolation transformers during this check). Using a "Leakage
repairing. Some model's power circuit is partly different in the Current Tester", measure the leakage current from each
GND. The difference of the GND is shown by the LIVE: ( ) exposed metal part of the cabinet, particularly any exposed
side GND, ISOLATED (NEUTRAL): ( ) side GND and metal part having a return path to the chassis, to a known good
EARTH: ( ) side GND. Don't short between the LIVE side earth ground (water pipe, etc.). Any leakage current must not
GND and ISOLATED (NEUTRAL) side GND or EARTH side exceed 0.5mA AC (r.m.s.).
GND and never measure with a measuring apparatus However, in tropical area, this must not exceed 0.2mA AC
(oscilloscope etc.) the LIVE side GND and ISOLATED (r.m.s.).
(NEUTRAL) side GND or EARTH side GND at the same time. If Alternate Check Method
above note will not be kept, a fuse or any parts will be broken. Plug the AC line cord directly into the AC outlet ( do not use a
line isolation transformer during this check.). Use an AC
5. If any repair has been made to the chassis, it is recommended voltmeter having 1000 ohms per volt or more sensitivity in the
that the B1 setting should be checked or adjusted (See following manner. Connect a 1500 10W resistor paralleled by
ADJUSTMENT OF B1 POWER SUPPLY). a 0.15F AC-type capacitor between an exposed metal part and
a known good earth ground (water pipe, etc.). Measure the AC
6. The high voltage applied to the picture tube must conform to voltage across the resistor with the AC voltmeter. Move the
that specified in Service manual. Excessive high voltage can resistor connection to each exposed metal part, particularly any
cause an increase in X-Ray emission, arcing and possible exposed metal part having a return path to the chassis, and
component damage, therefore operation under excessive high measure the AC voltage across the resistor. Now, reverse the
voltage conditions should be kept to a minimum, or should be plug in the AC outlet and repeat each measurement. Any
prevented. If severe arcing occurs, remove the AC power voltage measured must not exceed 0.75V AC (r.m.s.). This
immediately and determine the cause by visual inspection corresponds to 0.5mA AC (r.m.s.).
(incorrect installation, cracked or melted high voltage harness, However, in tropical area, this must not exceed 0.3V AC
poor soldering, etc.). To maintain the proper minimum level of (r.m.s.).
soft X-Ray emission, components in the high voltage circuitry This corresponds to 0.2mA AC (r.m.s.)
including the picture tube must be the exact replacements or
alternatives approved by the manufacturer of the complete
product.
7. Do not check high voltage by drawing an arc. Use a high
voltage meter or a high voltage probe with a VTVM. Discharge
the picture tube before attempting meter connection, by
connecting a clip lead to the ground frame and connecting the
other end of the lead through a 10k 2W resistor to the anode
button.
8. When service is required, observe the original lead dress. Extra
precaution should be given to assure correct lead dress in the
high voltage circuit area. Where a short circuit has occurred,
Enter Factory Menu
1 Entrance of factory controller: Use factory key to enter/switch/exit factory mode. Entrance of common
controller: When main menu appears, enter code 6483, which is equivalent to factory key.
2 Specification: Factory mode includes three kinds: FACTORY: for factory aging; B/W BALANCEfor
adjustment of black and white balance; ADJUSTfor all adjustments of factory.
Pressing factory key (or pressing 6483 when main menu appears) will display the following:
Common state FACTORY B/W BALANCE ADJUST
Factory Explanation
1 FACTORY (Aging mode): This mode is used for factory aging, in which TV set will not be turned off if
there is no signal.
2 Adjustment of B/W BALANCE: Press factory key to enter into B/W BALANCE and set value as table 1;
press "MUTE" key to enter horizontal line, and then adjust grid potentiometer to make the horizontal line
to bright up; adjust CUT R, CUT G AND CUT B (See table 2) to make the line turn white; and then adjust
grid potentiometer to make the line disappear. Press "MUTE" key to exit the line and dark balance is OK.
Fine tuning DRI R and DRI B to make the white to become pure white; and B/W BALANCE is OK.
Table 1
OSD Explanation 14-21 25-34
Indication
DRI R Adjust range of output R 0127 60 60
DRI B Adjust range of output B0127 63 63
CUT R Adjust base level of output R0255 100 100
CUT G Adjust base level of output G0255 100 100
CUT B Adjust base level of output B0255 100 100
BRI Adjust brightness of horizontal line0~255108 120
SIG 8 second built-in signal
Table 2
Key Name 1 2 3
Function CUT R+ CUT G+ CUT B+
Key Name 4 5 6
Function CUT R- CUT G- CUT B-
Note: BRI is only for adjusting voltage of grid, not for SUB-brightness; so please set BRI value as the
above table. It is better not to make any changes. If it needs to make change, please make it within the
range 14-21100-12025-34110-130.
2
3 ADJUSTMENT
Explanation of adjustments and settings: There are 11 pages for adjustments and settings from "SERVCJ0"
to "SERVCJ9" and "AUTO VCJ". It is available to turn down the page with MUTE key and swiftly arrive the
set page with 0-9 keys. Use P+/P- to select the adjusted item; and use VOL+ or VOL- to make set
adjustment.
0) Page SERVCJ0
No. Name Explanation
0 H PH Line center (range: 0~31)
1 V SH Vertical center (range: 0-7)
2 V SI Vertical range (range: 0-63)
3 V SC Vertical correction SC (range: 0-63) (effective only when choosing
M61264)
4 V LI Vertical linearity (range: 0-63) (effective only when choosing M61264)
5 N H PH Deviation amount of line center in NTSC (range: -31~+31)
6 N V SH Deviation amount of vertical center in NTSC (range: -7~+7)
7 N V SI Deviation amount of line center in NTSC (range: -63~+63)
8 N V SC Deviation amount of vertical correction SC in NTCS (range: -63~+63)
(effective only when choosing M61264)
9 N V LI Deviation amount of vertical linearity in NTCS (range: -63~+63)
(effective only when choosing M61264)
1) SERVCJ1
No. Name Explanation 30
0 AGC RF.AGC adjustment (range: 0~127) 1
1 HT Half-transparent switch (0: off; 1: on)
2 AUDIO Audio output (range: 0~127); effective only when the value of PWM 100
OPT of SERVCJ4 is more than 0.
3 YDL Time delay adjustment of brightness07 2
4 VDL V delay adjustment L (0~3) (effective only in YUV mode) 0
5 UDL U delay adjustment (0~3) (effective only in YUV mode) 0
6 YUV TINT YUV tincture adjustment 0~127(effective only in YUV mode) 50
2) Page SERVCJ2 (effective only in M61260)
No. Name Explanation
0 S BL R Adjustment of SECAM R-Y signal031 16
1 S BL B Adjustment of SECAM B-Y signal031 16
2 S YDL Time delay compensation of SECAM 0off 1on 0
3 S BPG Time delay option of SECAM BGP03 0
3
3Page SERVCJ3
No. Name Explanation
0 IC Option of decoding CMOS chip (M61260/M61264/M61266) M61264
1 SEA CHACK Checking of automatic channel searching when TV set is turned on.0 1
no 1yes
2 CAL Option of calendar (1yes/ 0no) 1
3 GAME Option of game (0no /1: yes) 1
4 ZOOM Option of ZOOM (1yes/ 0no) 1
5 LOCK Option of child lock (1yes/ 0no) 0
6 CURT Option of screen stretching (0no / 1on / 2off / 3both) 3
7 WOO Option of bass0no 1: base switch 2digital control 0
8 SAVER Option of screen protection (0no 1yes 2uper line LOGO 3: two line 1
LOGO)
4Page SERVCJ4
0 HP Left/right of OSD (range: 0~60) 28
1 VP Up/down of OSD (range: 0~60) 29
2 Z1 Vertical range data when screen is enlarged (range: 0~63) 58
3 Z2 Vertical range data when screen is widened (range: 0~63) 30
4 CURT TIM Time option of black screen before stretching screen when TV set is turned on 4
(range: 0~30 seconds)
5 PWM Volume option (0: inner volume control;, 1: 1-circuit PWM output; 2:2-circuit 0
PWM number, 3: IC control of acoustics)
6 AV AV option 01-circuit AV 1: 2-circuit AV 21-circuit AV, 1-circuit YUV 0
3: 2-circuit AV1-circuit YUV
7 S SYS Option of sound system (see note 1) 01111
8 POW Option of turning-on state (
0 direct turning on 1turning on after standby 22
memory turning on
Note 1: display 0 0 0 0 0
D/K
I
BG
M
5.742
As shown in the fig., the sound will be opened when each of the corresponding sound system is in 1 position;
and closed when in 0.
4
5Page SERVCJ5
0 V FREQ Option of middle frequency: 38.0MHZ38.9MHZ39.5MHZ45.75MHZ 38.0
34.47MHZ
1 V VCO Tuning of middle frequency: when tuning, AFT of the last line in the menu is in 26
OK mode.
2 V GAIN Scale control of video output0~7 7
3 H VCO Tuning of horizontal frequency (range: 0~7) 3
4 C TR limiting of color waves
0 ~ 3(ineffective when tuning in terminal S or YUV input) 0
6Page SERVCJ6
0 BS SW black level extending switch: 0on/1off 0
1 BS CHAG 03controlling of extending scale of black level03 2
2 BS DIS 03controlling of extending scale of black level03 0
3 BS GAIN Gaining switch of black level extending: 0normal1enhance 0
4 GAMMA 0~3Correction of curve GAMMA0~3 0
5 A SW limiting switch of automatic contrast: 0control of automatic contrast, 1 0
limiting of automatic contrast.
6 A GAIN ABCL gaining switch 0low, 1high 0
7 OM DET Checking of modulation: 0off, 1on 0
8 M/N ption of PAL-NPAL-M 0off, 1on 0
7Page SERVCJ7
0 D OSD OSD digit 1off 0on 0
1 OSD L Output scale of OSD digit: 0low 1high 1
2 S DOWN Sync cutting mode: 0: 50, 1: 40, 2: 30, 3: 25% 2
3 R MIX Adjustment of matrix R: 0normal 1enhance 1
4 VSY DET Switch of sync time testing: 011.5us 120.5us 0
5 BLACK SCR Option of screen blackening 1
6 VOL CHOICE Option of acoustics curves: 0standard 1customer 0
8Page SERVCJ8
0 SUB CONT Sub-contrast 0~29 18
1 SUB BRI Sub-brightness 0~105 20
2 SUB COL Sub-color 0~27 18
5
3 SUB SHA Sub-sharpness 0~13 13
4 SUB TI Sub-tincture 0~27 10
5 SA BR Screen protection and brightness of blueness in no-signal mode 0~255 138
6 LAN CHOICE Language option: 0: only English, 1: Chinese, English 1
7 TUNER TUNER OPTION: 0VS TUNER, 1: FS TUNER 0
CHOICE
9Page SERVCJ9 (effective only in choosing M61266)
0 Cr ADJ Adjustment of base level Cr 0~15
1 Cb ADJ Adjustment of base level Cb 0~15
2 SIF45 GAIN Attenuation of output scale of NTSC acoustics 00dB 1-6dB
3 SIF PAL enhancing of PAL SNR0OFF 1: ON
4 SIF PAL INV Polarity switch of SIF PAL0: NORMAL 1: INVERT
5 AMF Testing switch of weak radio-frequency signal0OFF 1:ON
6 AMF VTH Level adjustment of weak radio-frequency signal testing
7 AMF CUR reduce filtering current of MF AGC0: NORMAL 1: CURRENT
REDUCED
8 AMF HYS Switch HYS 0: OFF 1: ON
10Page AUTO VCJ: This menu automatically adjusts VIF VCO and S TRAP; and save the adjusted data in
EEPROM. Pressing volume key begins the automatic adjustment and it will return to original mode 2~3
seconds after adjustment.
Note 1: the adjusted datum will be shown in SER VCJ5.
Note 2: Adjusting will not affect any keys.
0 S TRAP
1 VIF VCO
Explanation of Special Function
1 Enter factory LOG set: press "LOGO" key will directly enter into adjusting mode; or in "AV" indication for
common controller in AV state, successively input 6483 will also enter into adjusting mode.
2Setting of factory LOGO: There are two lines for factory LOGO, the 1st of which is "Double Happiness" or
defined by customer; the 2nd of which is for customer to define (it is available for customer to set not more
than 13 characters). And customer may set switch, font, color, up/down position and left/right position. If
"LOGO" in the menu is set in "ON" position, the screen will show the equivalent "LOGO" when there is on
signal in POWER-ON state.
ˇ The setting menu of factory logo is displayed on two screens, which are available to adjust the 1st
line and 2nd line of the LOGO separately. After entering the setting menu, press POS+/POS to
6
choose different options. Yellow block will appear when displaying item is selected, and then use
VOL+/VOL- key to adjust the selected item.
ˇ Adjustment of the selected item: use RECALL key to select the shown item in 1st or 2nd line, when
yellow block indicates the current selectable character, use VOL+/VOL key to adjust the selected
character.
ˇ It is available to use "0" key to eliminate the current set character.
ˇ On setting menu, press DISPLAY key to indicate adjustment effect, and re-press DISPLAY key to
return LOGO set menu. Factory LOGO set is in "to gain what is seen"; and the other items, color, font,
position in the displaying lines are completely the same in normal display. So, while adjusting, it is
available to see the adjusted effect.
ˇ Setting of items in two lines. Do not set overlapping (even if one line is set in OFF position) so as to
prevent abnormal display.
ˇ When adjusting V POS, the menu probably may flash, but this will not affect LOGO display when TV
set is turned on.
3Note: After setting, change screen protection mode through factory setting item. Please see Page
SERVCJ3 for details.
6-2Realization of factory automatic adjustment
Note: There is no any effect for any key in BUS OPEN mode.
Pin 13 of CPU is the automatic adjustment ENABLE terminal; high level should be kept in normal
working state. When the terminal is connected to low level, CPU will transfer the control of BUS LINE to
automatic equipment (automatically enter into "BUS OPEN" mode); and the automatic equipment will send
data to decoding CMOS chip through BUS LINE to implement adjustment. Then it will save the adjusted
data in the address of equivalent EEPROM and recover the high level in ENABLE terminal. CPU returns to
normal working state. The concerned data of automatic decoding piece and EEPROM address are as
follows:
Address of EEPROM: written address: A0H read address: A1H
Address of decoding piece: written address: BAH read address: BBH
Name Sub-address in the Sub-address in the Max value
equivalent EEPROM equivalent decoding
piece
R.DIR 3BH 0BH 7FH
B.DIR 3CH 0CH 7FH
R.CUTOFF 3DH 0DH FFH
G.CUTOFF 3EH 0EH FFH
B.CUTOFF 3FH 0FH FFH
7
PURITY / CONVERGENCE ADJUSTMENT
8
PURITY ADJUSTMENT
1. Demagnetize CRT with the demagnetizer. WEDGE
DEFLECTION YOKE
2. Loosen the retainer screw of the deflection yoke.
P
3. Remove the wedges. CRT
4. Input a green raster signal from the signal generator,
and turn the screen to green raster. 4 6
5. Move the deflection yoke backward.
P/C MAGNETS
6. Bring the long lug of the purity magnets on the short
lug and position them horizontally. (Fig2) P: PURITY MAGNET
4: 4-POLES (convergence magnets)
7. Adjust the gap between two lugs so that the GREEN 6: 6-POLES (convergence magnets)
RASTER will come into the centre of the screen.
(Fig. 3)
8. Move the deflection yoke forward, and fix the position Fig. 1
of the deflection yoke so that the whole screen will
become green.
9. Insert the wedge to the top side of the deflection yoke PURITY MAGNETS
so that it will not move.
Long lug
10. Input a crosshatch signal.
11. Verify that the screen is horizontal.
12. Input red and blue raster signals, and make sure that
purity is properly adjusted.
Short lug
Bring the long lug over the short lug and
position them horizontally.
Fig. 2
(FRONT VIEW)
GREEN RASTER
CENTER
Fig. 3
9
STATIC CONVERGENCE ADJUSTMENT
1. Input a crosshatch signal.
2. Using 4-pole convergence magnets overlap the red
and blue lines in the center of the screen (Fig. 1) and
turn them to magenta (red/blue).
(FRONT VIEW)
3. Using 6-pole convergence magnets overlap the
magenta (red/blue) and green lines in the center of the
screen and turn them to white.
4. Repeat 2 and 3 above, and make the best
convergence.
Fig. 1
(FRONT VIEW)
DYNAMIC CONVERGENCE ADJUSTMENT
RED GREEN BLUE
1. Move the deflection yoke up and down and overlap
lines in the periphery. (Fig. 2) BLUE
RED
2. Move the deflection yoke left to right and overlap the
lines in the periphery. (Fig. 3) GREEN GREEN
RED BLUE
3. Repeat 1 and 2 above, and make the best
convergence.
BLUE GREEN RED
Fig.2
(FRONT VIEW)
After adjustment, fix the wedge at the original position. RED GREEN BLUE BLUE GREEN RED
Fasten the retainer screw of the deflection yoke.
Fix the 6 magnets with glue. RED
GREEN
BLUE
BLUE
GREEN
RED
Fig. 3
10
List of Parts
14" ~ 21"
Description Q'ty Location
1 HZ5C2(5.1V) 4 VD902 VD110 VD111 VD452
2 6.2V 1W/IN4735A 1 VD561
3 HZ7C2(7.5V) 1 VD519
4 HZ9A2(8.2V) 4 VD601 VD602 VD603 VD904
5 UPC574/CW574 1 VD101
6 IN4148 13 VD133 VD203 VD514 VD516 VD518
VD537 VD538 VD903 VD914
VD600 VD607 VD608 VD609
7 IN4002(10L) 1 VD451
8 IN4002(12.5L) 1 VD135
9 FR154(12.5L) 2 VD448 VD517
10 FR154(12.5LH) 3 VD553 VD554 VD555
11 FR157(12.5LH) 1 VD552
12 HER308(20LH) 1 VD551
13 RL207(12.5L) 4 VD503 VD504 VD505 VD506
14 2SA1015Y 1 V600
15 2SC1815Y 3 V102 V553 V604
16 2SC1815GR 1 V191
17 2SC1674/2SC388A 1 V101
18 HSB772P/3CA8772/B764 1 V511
19 2SC2383-O 4 V901 V132 V133 V701
20 HBF422 3 V651 V652 V653
21 2SC3807 1 V512
22 2SC5296/TT2190 1 V413
23 ST1802/2S5297 1 V513
24 PC817B/Q817/F817 1 N501
25 ATME24C08/24LC08 1 N602
26 AN5522/ST9302 1 N451N401
27 TDA2003 1 N301
M37160M8-058FP or
28 M37160M8-063FP or 1 N601
M37160M8-064FP
29 M61266 1 N101
30 F3828H(38MHz) 1 Z101
31 JA18B-4.43MHZ(S) 1 Z601
32 CBB21-250V-684J 1 C441
33 CBB62-250V-224K 1 C501
34 CBB81-1.6KV-103J 1 C436
35 2 C605 C606
36 CC1-SL-50V-181J 1 C604
37 CC1-50V-101J 1 C719
38 CC1-50V-221J 2 C601 C715
39 CT1-50V-471K 3 C122 C713 C621
40 CT1-50V-331K 2 C622 C623
11
41 CT1-50V-102K 3 C119 C611 C721
42 CT1-50V-103Z 17 C101 C102 C115 C116 C121
C198 C205 C207 C211 C315
C629 C708 C711 C716 C718
C903 C905
43 CT1-500V-471K 3 C553 C554 C555
44 CT1-500V-102K 1 C930
45 CT1-500V-392K 1 C931
46 CT81-B-1KV-471K 2 C551 C552
47 CT81-B-1KV-102K 2 C503 C505
48 CT81-B-2KV-681K 1 C516
49 CT81-B-2KV-102K 1 C630
50 CT7-400VAC-222M 1 C535
51 CL11-100V-222K 1 C306
52 CL11-100V-472K 1 C312
53 CL11-100V-103K 3 C124 C901 C906
54 CL11-100V-153K 1 C603
55 CL11-100V-333K 1 C456
56 CL11-100V-104K 5 C307 C438 C451
C203 C363
57 CL21X-63V/100V-153J 2 C515 C517
58 CL21X-100V/63V-104J 3 C117 C401 C514
CL21X-100V/63V-224J 3 C108 C118 C191
59 CL21X-100V/63V-474J 1 C433
60 CL21X-100V/63V-334J 1 C402
61 CD110-16V-10UF-M 5 C110 C131 C144 C1 C808
62 CD110-16V-47UF-M 2 C628 C923
63 CD110-16V-100UF-M 7 C104 C114 C212 C814 C904
C380 C600
64 CD110-16V-220UF-M 2 C206 C706
65 CD110-16V-470UF-M 1 C130
66 CD110-16V-1000UF-M 1 C564
67 CD110-25V-470UF-M 2 C565 C362
68 CD110-25V-1000UF-M 2 C455 C316
69 CD110-35V-47UF-M 1 C932
70 CD110-35V-100UF-M 1 C452
71 CD110-35V-470UF-M 1 C563
72 CD110-35V-1000UF-M 1 C453
73 CD110-50V-0.22UF-M 1 C125
74 CD110-50V-0.47UF-M 1 C123
75 CD110-50V-1UF-M 7 C165 C304 C308 C366
C602 C902 C215
76 CD110-50V-3.3UF-M 1 C454
77 CD110-50V-4.7UF-M 7 C105 C106 C107 C109 C113
C303 C309
78 CD110-160V-100UF+20% 1 C561
79 CD110-250V-4.7UF-M(5 1 C444
80 CD110-250V-22UF-M 1 C562
81 CD293-400V-100UF-M 1 C507
12
82 JLC-96-37UH/YDD-37UH 1 L401
83 LGA0307-151K 1 L600
84 LGA0307-1R2K 1 L101
85 LGA0307-100K 2 L133 L644
86 LGA0307-100K 1 L103
87 LGA0307-330K 1 L601
88 LGA0410-180K(12.5) 1 R599
89 RJ-1/4W-2.2K-1% 1 R526
90 RT-1/6W-1-J 1 R453
91 RT-1/6W-2.2-J 1 R362
92 RT-1/6W-27-J 1 R102
93 RT-1/6W-33-J 1 R611
94 RT-1/6W-56-J 3 R621 R622 R623
95 RT-1/6W-82-J 1 R823
96 RT-1/6W-100-J 12 R105 R114 R126 R129 R198
R203 R204 R722 R824
R671 R672 R673
97 RT-1/6W-180-J 3 R604 R605 R606
98 RT-1/6W-220-J 2 R110 W230
99 RT-1/6W-270-J 1 R107
100 RT-1/6W-470-J 2 R115 R117
RT-1/6W-560-J 1 R454
101 RT-1/6W-330-J 3 R631 R632 R633
102 RT-1/6W-1K-J 5 R104 R112 R205 R517 R716
103 RT-1/6W-1.8K-J 2 R523 R310
104 RT-1/6W-2.2K-J 8 R601 R602 R603 R727
R545 R641 R642 R643
105 RT-1/6W-4.7K-J 6 R101 R103 R119 R712 R816
R111
106 RT-1/6W-5.6K-J 2 R511 R553
107 RT-1/6W-6.8K-J 5 R307 R614 R724 R725 R901
108 RT-1/6W-10K-J 6 R113 R120 R600 R711 R903
W165
109 RT-1/6W-12K-J 1 R461
RT-1/6W-15K-J 1 R462
110 RT-1/6W-22K-J 6 R457 R515 R556 R719 R720
R723
111 RT-1/6W-47K-J 3 R207 R211 R730
112 RT-1/6W-100K-J 1 R815
113 RT-1/4W-3.3-J 1 RR452
114 RT-1/4W-4.7-J 1 R363
115 RT-1/4W-22-J 1 R519
116 RT-1/4W-100-J 1 R800
117 RT-1/4W-150-J 1 R914
118 RT-1/4W-220-J 1 R361
119 RT-1/4W-270-J 1 R938
120 RT-1/4W-470-J 1 W161
13
121 RT-1/4W-1K-J 2 R180 R930
122 RT-1/4W-1.2K-J 2 R917 R936
123 RT-1/4W-2.2K-J 2 R906 R726
124 RT-1/4W-4.7K-J 3 R312 R701 R702
125 RT-1/4W-10K-J 4 R116 R703 R713 R902
126 RT-1/4W-15K-J 3 R121 R522 R560
127 RT-1/4W-22K-J 1 R731
128 RT-1/4W-120K-J 1 R904
129 RT-1/4W-1M-J 1 R907
130 RT-1/2W-270-J 1 R466
131 RT-1/2W-1K-J 1 R443
132 RT-1/2W-2.7K-J 3 R691 R692 R693
133
134 RT-1/2W-22K-J 2 R440 R448
135 RT-1/2W-100K-J 1 R552
136 RT-1/2W-120K-J 2 R520 R521
137 RT-1/2W-150K-J 1 R554
138 RT-1/2W-220K-J 2 R501 R558
139 RY(15)-1/2W-1K-J 1 R441
140 RY(15)-1/2W-1.8-J 1 R452
141 RY(20)-1W-12-J 1 R142
142 RY(20)-1W-39-J 1 R709
143 RY-1W-47K-J 1 R555
144 RY-2W-1-J(17.5LH) 1 R562
145 RY-2W-1.5-J(17.5LH) 1 R437
146 RY-2W-12-J(17.5LH) 2 R133 R134
147 RY-2W-270-J(15LH) 1 R436
148 RY-2W-12K-J(20LH) 4 R551
R681 R682 R683
149 RY-3W-68-J(20LH) 2 R525A R524
150 RXG-5W-8.2-J 1 VD436
151 RS11-1/2W-12M-K 1 R531
152 MF72-2-7-M 1 R502
153 MZ72-14RM 1 RT501
154 WI06-2-2K-M 1 RP551
ET-5G1E-CV100(063Y)(38MHz)
155 1 U101
/ET-5CE-V01
156 21" BSC24-01N4006E 1 T471
14" BSC24-01N4010G/
BSC24-01N4010GA
157 JBC-145-UU10.5 1 T901
158 BCK40-45-1275 1 T511
159 JLF-98-UF16 1 L501
160 T3.15AL250VAC 1 FUSE
161 Fuse Clip 2 FUSE
162 GZS10-2-108C 1 CRT
163 TJC1-1A 1 GND
164 TJC1-2A 2 XS501 XS502
165 TJC2-5A(DY) 1 XS901
166 TJC2-5A(L=7) 1 XS408
14
167 TJC3-2A 3 XS303 XS302 XS703
168 TJC3-3A 2 XS702 XS803
169 TJC3-4A 2 XS402 XS701
170 TJC3-5A 1 XS601
171 YG-2A 1 XP451
172 TJC3-4Y-450mm 1 XP602
173 TJC3-5Y-450mm 1 XP601
174 21MMT1 1 V513
175 21MMHV2 1 V413
176 21MMB1-1 1 N301
Bare Wire
182 5mm 24 W130 W176 W199 W203 W212
W214 W231 W309 W360 W366
W429 W439 W504 W515 C810
C936 L430 R580 XS1 W112(1)-W213(3)
W600 W601 W602 W606
183 7.5mm 18 W1 W132 W133 W134 W151
W168 W170 W174 W178 W179
W184 W185 W192 W206
W511 R308 W152 R820
184 10mm 16 L502*2 W147 W148 W155
W164 W172 W173 W181 W182
W183 W204 W431 W507
R416 W603
185 12mm 1 C807
- -R818
8
186 12.5mm 6 W137 W149 W162 W177 W201
W190
187 14mm 1 N801(2)-W210)
188 15mm 11 W100 W131 W135 W153 W157
W158 W159 W186 W187 W209
W438
R8144-W211
189 16mm 1
1
190 17.5mm 5 W141 W142 W156 W188
W189
191 20mm 5 W143 W154 W169 W202 N301:1-9
1 RT-1/6W-1.5K-J 1 R1015
2 RT-1/6W-2.4K-J 1 R702
3 RT-1/6W-3.6K-J 1 R701
4 RT-1/6W-3.9K-J 1 R703
5 RT-1/6W-6.2K-J 1 R704
6 RT-1/6W-12K-J 1 R705
7 CD110-16V-47UF-M 1 C1101
BRM-1040/FPS-6038-T53
8 /MIM-5383K4 /MIM-5383J2/
MIM-5383K4-F-5 1 RM
15
25" ~ 34"
Description Q'ty Location
1 HZ5C2(5.1V) 3 VD902 VD110 VD111
2 6.2V 1W/1N4735A 1 VD561
3 HZ7C2(7.5V) 2 VD519 VD452
4 HZ9A2(8.2V) 4 VD601 VD602 VD603 VD904
5 UPC574/CW574 1 VD101
6 IN4148 13 VD133 VD203 VD514 VD516 VD518
VD537 VD538 VD903 VD914 VD600
VD607 VD608 VD609
7 IN4002(10L) 1 VD451
8 IN4002(12.5L) 1 VD135
9 FR154(12.5L) 2 VD448 VD517
10 FR154(12.5LH) 3 VD553 VD554 VD555
11 FR157(12.5LH) 1 VD552
12 FR305(12.5LH) 1 VD436
13 BY228(20LH) 1 VD435
14 SF36(20LH) 1 VD551
15 RL207(12.5L) 4 VD503 VD504 VD505 VD506
17 2SA1015Y 1 V600
18 2SC1815Y 7 V102 V110 V201 V553
V604 V830 V831
19 2SC1815GR 1 V191
20 2SC1674/2SC388A 1 V101
21 HSB772P 1 V511
22 2SC2383-O 4 V901 V132 V133 V701
23 2SC2688 3 V651 V652 V653
24 2SC3807 1 V512
25 2SC5296 1 V413
26 2SC4460-M 1 V513
27 D2012 1 V303
29 LTV817B 1 N501
30 ATME24C08/24LC08 1 N602
31 TDA8177 1 N451
32 AN7522 1 N301
M37160M8-058FP/M37160M8H-051FP
33 or M37160M8-063FP or 1 N601
M37160M8-064FP
34 M61266 1 N101
35 MCI4053B/HEF4053/CD4053/HCF4053 1 N801
37 F3828H 1 Z101
38 JA18B-4.43MHZ(S) 1 Z601
39 CBB21-630V-473J 1 C433
40 CBB21-400V-684J 1 C441
41 CBB62-250VAC-224K 1 C502
42 CBB81-1.6KV-103J 1 C436
43 CBB81-1.6KV-822J 1 C439
44 CC1-SL-50V-181J 1 C604
45 CC1-50V-101J 1 C719
16
46 CC1-50V-221J 2 C601 C715
47 CC1-50V-22PF-J 2 C605 C606
CT1-50V-331K 2 C622 C623
48 CT1-50V-471K 3 C122 C621 C713
49 CT1-50V-102K 3 C119 C611 C721
50 CT1-50V-103Z 18 C101 C102 C115 C116 C121
C198 C205 C207 C211 C315
C629 C708 C711 C716 C718
C800 C903 C905
51 CT1-500V-471K 3 C553 C554 C555
52 CT1-500V-102K 1 C930
53 CT1-500V-392K 1 C931
54
55 CT81-B-1KV-471K 2 C551 C552
56 CT81-B-1KV-102K 4 C503 C505 C504 C506
57
58 CT81-B-2KV-102K 2 C630 C516
59
60 CT7-400VAC-472M 1 C535
62 CL11-100V-222K 1 C306
63 CL11-100V-472K 2 C311 C312
64 CL11-100V-103K 3 C124 C901 C906
CL11-100V-153K 1 C603
66 CL11-100V-333K 1 C456
67 CL11-100V-104K 3 C203 C307 C438
CL21X-63V/100V-153J 2 C515 C517
68 CL21X-100V/63V-104J 3 C117 C401 C514
69 CL21X-100V/63V-224J 3 C108 C118 C191
70 CL21X-100V/63V-334J 1 C402
71 CL21X-100V/63V-474J 1 C451
CL21X-100V/63V-224J
72 CD71S-50V-10UF-M 1 C302
73 CD71-160V-4.7UF-M 1 C444
74 CD110-16V-10UF-M 15 C1 C110 C131 C144 C314
C704 C801 C802 C807 C808
C809 C810 C811 C812 C896
75 CD110-16V-47UF-M 2 C628 C923
76 CD110-16V-100UF-M 6 C104 C114 C212 C814 C904
C600
77 CD110-16V-220UF-M 2 C206 C706
78 CD110-16V-470UF-M 1 C130
79 CD110-16V-1000UF-M 3 C564 C316 C565
80 CD110-25V-2200UF-M 1 C455
81 CD110-35V-47UF-M 1 C932
82 CD110-35V-100UF-M 1 C452
83 CD110-35V-470UF-M 1 C563
84 CD110-35V-1000UF-M 1 C453
17
85 CD110-50V-0.22UF-M 1 C125
86 CD110-50V-0.47UF-M 1 C123
87 CD110-50V-1UF-M 8 C165 C304 C308 C320 C366
C602 C617 C902
88 CD81-50V-4.7UF-M 105 1 C454
89 CD110-50V-4.7UF-M 8 C105 C106 C107 C109 C113
C303 C309 C310
90 CD110-160V-220UF-M 1 C561
91 CD110-250V-22UF-M 1 C562
92 CD293-400V-220UF-M 1 C507
94 18UH 1 L401
95 410UH 1 L301
96 LGA0307-151K 1 L600
97 LGA0307-1R2K 1 L101
98 LGA0307-100K 2 L133 L644
99 LGA0307-100K 1 L103
100 LGA0307-330K 1 L601
101 LGA0410-180K(12.5) 1 R599
102 RJ-1/6W-22Ką1% 1 R457
103 RJ-1/6W-15Ką1% 1 R462
104 RJ-1/4W-2.2Ką1% 1 R526
105 RT-1/6W-1-J 1 R453
106 RT-1/6W-27-J 1 R102
107 RT-1/6W-33-J 1 R611
108 RT-1/6W-56-J 3 R621 R622 R623
109 RT-1/6W-68-J 1 R806
110 RT-1/6W-82-J 3 R817 R823 R890
111 RT-1/6W-100-J 14 R105 R114 R126 R129 R198
R203 R204 R671 R672 R673
R722 R818 R824 R833
112 RT-1/6W-180-J 3 R604 R605 R606
113 RT-1/6W-220-J 2 R110 W230
114 RT-1/6W-270-J 1 R107
115 RT-1/6W-470-J 3 R115 R117 R454
116 RT-1/6W-300-J 3 R631 R632 R633
117 RT-1/6W-1K-J 9 R104 R112 R205 R222 R316
R517 R716 R803 R804
118 RT-1/6W-1.5K-J 1 R317
119 RT-1/6W-1.8K-J 1 R523
120 RT-1/6W-2.2K-J 11 R111 R601 R602 R603
R641 R642 R643 R727 R306
R307 R545
122 RT-1/6W-3.3K-J 1 R835
123 RT-1/6W-4.7K-J 12 R101 R103 R119 R309 R310
R712 R743 R814 R816 R820
R822 R553
124 RT-1/6W-5.6K-J 1 R511
125 RT-1/6W-6.8K-J 4 R614 R724 R725 R901
126
18
127 RT-1/6W-10K-J 6 R113 R120 R600 R711 R903
W165
128 RT-1/6W-12K-J 1 R461
129
130 RT-1/6W-22K-J 9 R315 R515 R556 R719
R720 R723 R808 R832 R211
131
132 RT-1/6W-47K-J 2 R207 R730
133 RT-1/6W-68K-J 1 R313
134 RT-1/6W-100K-J 6 R801 R802 R813 R815 R819
R821
135 RT-1/6W-270K-J 1 R314
136 RT-1/6W-8.2M-J 1 R300
137 RT-1/4W-22-J 1 R519
138 RT-1/4W-22-J 1 R224
139 RT-1/4W-100-J 1 R800
140 RT-1/4W-150-J 1 R914
141 RT-1/4W-270-J 1 R938
142 RT-1/4W-470-J 1 W161
143 RT-1/4W-1K-J 2 R180 R930
144 RT-1/4W-1.2K-J 2 R917 R936
145 RT-1/4W-2.2K-J 2 R906 R726
146 RT-1/4W-4.7K-J 3 R312 R701 R702
147 RT-1/4W-10K-J 5 R116 R703 R713 R830 R902
148 RT-1/4W-15K-J 4 R121 R522 R560 R440
149 RT-1/4W-22K-J 2 R731 R831
150 RT-1/4W-120K-J 1 R904
151 RT-1/4W-1M-J 1 R907
153 RT-1/2W-3.3-J 1 RR452
154 RT-1/2W-270-J 1 R466
155 RT-1/2W-1K-J 1 R443
156 RT-1/2W-2.7K-J 3 R691 R692 R693
157 RT-1/2W-22K-J 1 R448
158 RT-1/2W-100K-J 1 R552
159 RT-1/2W-120K-J 2 R520 R521
160 RT-1/2W-150K-J 1 R554
161 RT-1/2W-220K-J 2 R501 R558
163 RY(15)-1/2W-1K-J 1 R441
164 RY(15)-1W-1.2-J 1 R452
165 RY(20)-1W-12-J 1 R142
166 RY(15)-1W-5.1-J 1 R330
167 RY(20)-1W-39-J 1 R709
168 RY-1W-47K-J 1 R555
169 RY-1W-560-J(15LH) 1 R463
170 RY(17.5)-2W-1-J 1 R562
171 RY(17.5)-2W-1.5-J 1 R437
172 RY(17.5)-2W-12-J 2 R133 R134
173 RY(15)-2W-270-J 1 R436
174 RY(20)-2W-10K-J 3 R681 R682 R683
19
175 RY-2W-15K-J(20LH) 1 R551
176 RS11-1/2W-12M-K 1 R531
177 RXG-7W-2.2-J 1 R502
178 RY-2W-1-J 1 R580
179 RXG-5W-22-J(15) 1 R524
180 RXG-5W-39-J(15) 1 R525A
181 MZ73-14RM 1 RT501
182 WI06-2-2K-M 1 RP551
185 ET-5G1E-CV100(063Y)/ET-5CE-V01 1 U101
186 BSC26-01N4010A 1 T471
187 JBC-184-E119 1 T901
188 BCK40-45-1243-1 1 T511
189 JLF-148-ET24 2 L501 L502
190 T3.15AL250VAC 1 FUSE
191 Fuse Clip 2 FUSE
192 SW-3K 1 S-IN
193 GZS10-2-108C 1 CRT
194 AV6-14 1 AV2
197 TJC1-1A 1 GND
198 TJC1-2A 2 XS501 XS502A
199 TJC2-5A(DY) 1 XS901
200 TJC2-5A(L=7) 1 XS408
201 TJC3-2A 4 XS301 XS302 XS703 XS1
202 TJC3-3A 2 XS702 XS102
203 TJC3-4A 3 XS402 XS701 XS803
204 TJC3-5A 1 XS601
205 YG-2A 1 XP451
207 TJC3-4Y-500mm 1 XP602
208 TJC3-5Y-500mm 1 XP601
Bare Wire
223 5MM 23 W130 W176 W199 W203 W212
W214 W231 W360 W366 W429
W439 W504 W515 W600 W601
W602 W606 C804 C936 W210
W310 W362 C362
224 7.5MM 19 W1 W132 W133 W134 W151
W168 W170 W174 W178 W179
W184 W185 W192 W206 W512
W152 W211 W604 R308
225 10MM 14 W147 W148 W603 W155
W164 W172 W173 W181 W182
W183 W204 W431 W507 R416
226 12.5MM 8 W137 W149 W162 W177 W201
W171 L430 W190
227 15MM 13 W100 W131 W135 W153 W157
W158 W159 W186 W187 W209
W438 W160 W208
228 17.5MM 5 W141 W142 W156 W188 W189
20
229 20MM 4 W143 W154 W169 W202
230 RT-1/6W-1.5K-J 1 R1015
231 RT-1/6W-2.4K-J 1 R702
232 RT-1/6W-3.6K-J 1 R701
233 RT-1/6W-3.9K-J 1 R703
234 RT-1/6W-6.2K-J 1 R704
235 RT-1/6W-12K-J 1 R705
236 CD110-16V-47UF-M 1 C1101
BRM-1040/FPS-6038-T53
237 /MIM-5383K4
/MIM-5383J2/MIM-5383K4-F-5 1 RM
21
Y Cb Cr
4 4
XS302 XS302 B901
Rin1 3 3 TJC3-2A 10W8OHM
B2 TJC3-2Y
IC301 AN7522
2 R891 R892 C892 10V
2 + C316
STBY
75 100K
GND
GND
GND
100K C315
VCC
S-3K Vin1 75 120
VOL
RIN
104