Text preview for : lg_rf04ga_chassis_mz42pm12x_plasma_[ET].pdf part of LG MZ-42PM12X PLASMA TV
Back to : lg_rf04ga_chassis_mz42pm1 | Home
website:http://biz.LGservice.com e-mail:http://www.LGEservice.com/techsup.html
PLASMA MONITOR SERVICE MANUAL
CHASSIS : RF-04GA
MODEL : MZ-42PM12X
CAUTION
BEFORE SERVICING THE CHASSIS, READ THE SAFETY PRECAUTIONS IN THIS MANUAL.
CONTENTS
CONTENTS .............................................................................................................2 SAFETY PRECAUTIONS .......................................................................................3 ADJUSTMENT INSTRUCTIONS ............................................................................4 SPECIFICATIONS ................................................................................................ 13 ADJUSTMENT INSTRUCTIONS ..........................................................................16 TROUBLE SHOOTING GUIDE .............................................................................18 BLOCK DIAGRAM ................................................................................................29 EXPLODED VIEW .................................................................................................32 EXPLODED VIEW PARTS LIST ...........................................................................33 REPLACEMENT PARTS LIST..............................................................................34 SCHEMATIC DIAGRAM ........................................................................................... PRINTED CIRCUIT BOARD .....................................................................................
- 2 -
SAFETY PRECAUTIONS
IMPORT ANT SAFETY NOTICE
Many electrical and mechanical parts in this chassis have special safety-related characteristics. These parts are identified by in the Schematic Diagram and Replacement Parts List. It is essential that these special safety parts should be replaced with the same components as recommended in this manual to prevent X-RADIATION, Shock, Fire, or other Hazards. Do not modify the original design without permission of manufacturer.
General Guidance
An isolation Transformer should always be used during the servicing of a receiver whose chassis is not isolated from the AC power line. Use a transformer of adequate power rating as this protects the technician from accidents resulting in personal injury from electrical shocks. It will also protect the receiver and it's components from being damaged by accidental shorts of the circuitry that may be inadvertently introduced during the service operation. If any fuse (or Fusible Resistor) in this monitor is blown, replace it with the specified. When replacing a high wattage resistor (Oxide Metal Film Resistor, over 1W), keep the resistor 10mm away from PCB. Keep wires away from high voltage or high temperature parts. Due to high vacuum and large surface area of picture tube, extreme care should be used in handling the Picture Tube. Do not lift the Picture tube by it's Neck.
Leakage Current Hot Check (See below Figure)
Plug the AC cord directly into the AC outlet. Do not use a line Isolation Transformer during this check. Connect 1.5K/10watt resistor in parallel with a 0.15uF capacitor between a known good earth ground (Water Pipe, Conduit, etc.) and the exposed metallic parts. Measure the AC voltage across the resistor using AC voltmeter with 1000 ohms/volt or more sensitivity. Reverse plug the AC cord into the AC outlet and repeat AC voltage measurements for each exposed metallic part. Any voltage measured must not exceed 0.75 volt RMS which is corresponds to 0.5mA. In case any measurement is out of the limits specified, there is possibility of shock hazard and the set must be checked and repaired before it is returned to the customer.
Leakage Current Hot Check circuit
AC Volt-meter
Leakage Current Cold Check(Antenna Cold Check)
With the instrument AC plug removed from AC source, connect an electrical jumper across the two AC plug prongs. Place the AC switch in the on position, connect one lead of ohm-meter to the AC plug prongs tied together and touch other ohm-meter lead in turn to each exposed metallic parts such as antenna terminals, phone jacks, etc. If the exposed metallic part has a return path to the chassis, the measured resistance should be between 1M and 5.2M. When the exposed metal has no return path to the chassis the reading must be infinite. An other abnormality exists that must be corrected before the receiver is returned to the customer.
To Instrument's exposed METALLIC PARTS
Good Earth Ground such as WATER PIPE, CONDUIT etc.
0.15uF
1.5 Kohm/10W
- 3 -
DESCRIPTION OF CONTROLS
Remote Control Key Functions
- When using the remote control aim it at the remote control sensor of the set. - There's maybe a defect in consecutive operation of remote control in specified brightness according to this set feature.
MUTE Switches the sound on or off. MULTIMEDIA Selects the Component, RGB or DVI modes. PIP INPUT Selects the input mode for the sub picture. EXIT Clears all on-screen displays.
MUTE POWER
POWER switches the set on from standby or off to standby. INPUT SELECT
PIP INPUT MULTIMEDIA INPUT SELECT
EXIT
ARC
MENU
ARC Changes the picture format.
D /E Selects a menu option. F / G (Volume Up/Down) Increases/decreases sound level. Adjusts menu settings. OK accepts your selection or displays the current mode.
MENU Displays on screen menus one by one. Exits the current menu. Memorizes menu changes.
OK
VOL VOL
NUMBER buttons
1 4
PSM Adjusts the factory preset picture according to the room. SPLIT ZOOM Enlarge the screen with regular ration. WIN.SIZE Adjusts the sub picture size.
2 5 8 0
3 6 9 SSM
SLEEP
SSM To select the sound appropriate to your viewing programme character.
7 PSM
SPLIT ZOOM PIP/DW
PIP/DW Switches the sub picture on or off. Selects PIP or DW modes. SLEEP Sets the sleep timer. SWAP Alternates between main and sub picture.
WIN. SIZE POSITION SCANSKIPPLAY STOP PAUSE
SWAP SCAN+ SKIP+ POWER
POSITION Moves the sub picture to D / E or F / G direction.
DVD BUTTONS controls a LG DVD player.
- 4 -
- Shown is a simplified representation of the set. - Here shown may be somewhat different from your set.
6
3
ON/OFF
5 2 4
1
or
ON/OFF
INPUT SELECT
MENU
VOL
1
2
3
4
5
6
1. Main Power Button 2. Remote Control Sensor 3. Power Standby Indicator Illuminates red in standby mode, Illuminates green when the set is turned on 4. INPUT SELECT Button
5. MENU Displays on screen menus one by one. Exits the current menu. Memorizes menu changes. 6. D / E Selects a menu option. F / G (Volume Up/Down) Increases/decreases sound level. Adjusts menu settings.
- 5 -
R
REMOTE CONTROL
L
RS-232C INPUT
(CONTROL/SERVICE)
DVI INPUT
AUDIO INPUT
RGB INPUT
RGB OUTPUT
Y
PB
PR
R
L R AUDIO L
(MONO)
AC INPUT S-VIDEO AUDIO INPUT VIDEO INPUT EXTERNAL SPEAKER
COMPONENT INPUT
AUDIO INPUT
Connection to PC
Connection to AV equipment
- 6 -
RCA Type
R
REMOTE CONTROL
L
RS-232C INPUT
(CONTROL/SERVICE)
DVI INPUT
AUDIO INPUT
RGB INPUT
RGB OUTPUT
Y
PB
PR
R
L R AUDIO L
(MONO)
AC INPUT S-VIDEO AUDIO INPUT VIDEO INPUT EXTERNAL SPEAKER
COMPONENT INPUT
AUDIO INPUT
1
2
3
5
4
6
Scart Type
R
REMOTE CONTROL
L
RS-232C INPUT
(CONTROL/SERVICE)
DVI INPUT
AUDIO INPUT
RGB INPUT
RGB OUTPUT
Y
PB
PR
R
L
AV1 AV2
AC INPUT EXTERNAL SPEAKER
COMPONENT INPUT
AUDIO INPUT
S-VIDEO
5
AV1
1. CONTROL LOCK / REMOTE CONTROL 2. RS-232C INPUT(CONTROL/SERVICE) PORT Connect to the RS-232C port on a PC. 3. DVI INPUT / AUDIO INPUT / RGB INPUT SOCKETS Connect the monitor output socket of the PERSONAL COMPUTER to this socket. RGB OUTPUT SOCKET You can watch the RGB signal on another monitor, connect RGB OUTPUT to another monitor's PC input port. 4. EXTERNAL SPEAKER OUTPUT (8 ohm) Connect to optional external speaker(s). * For further information, refer to `Speaker & Speaker Stand' manual.
5. COMPONENT / AUDIO INPUT SOCKETS S-VIDEO / AUDIO (L/MONO) INPUT SOCKETS VIDEO / AUDIO (L/MONO) INPUT SOCKETS EURO SCART SOCKET
Note: If you want to use your external hi-fi stereo system, turn off the internal speakers of the set.
6. POWER CORD SOCKET This Monitor operates on an AC power. The voltage is indicated on the Specifications page. Never attempt to operate the Monitor on DC power.
- 7 -
External Equipment Viewing Setups
Watching VCR (When the Interface board is installed.)
- When connecting the Plasma Monitor with external equipments, match the colours of connecting ports (Video - yellow, Audio(L) - white, Audio(R) -red). - Connect the VIDEO INPUT socket(yellow) with the BNC-RCA adapter to the VIDEO INPUT socket of the set. - If you have a mono VCR, connect the audio cable from the VCR to the AUDIO(L/MONO) input of the Plasma Monitor. - If you connect an S-VIDEO VCR to the S-VIDEO input, the picture quality is improved; compared to connecting a regular VCR to the Video input. - Or, connect the Euro scart socket of the VCR to the Euro scart socket of the set. Avoid having a fixed image remain on the screen for a long period of time. Typically a frozen still picture from a VCR, 4:3 picture format or if a CH label is present; the fixed image may remain visible on the screen. Use the orbiter function to avoid having a fixed image. (Refer to p.20) 1. Press INPUT SELECT button on the remote control and select AV or (AV1 or AV2). (When connecting with S-Video, select the S-Video.) 2. Insert a video tape into the VCR and press the PLAY button on the VCR. (See VCR owner's manual)
Watching Cable TV (When the Interface board is installed.)
- After subscribing to a cable TV service from a local provider and installing a converter, you can watch cable TV programming. This monitor cannot display TV programming without a TV tuner device or cable TV converter box connected to the monitor. 1. Press INPUT SELECT button on the remote control and select AV or (AV1 or AV2). 2. Tune to cable service provided channels using the cable box.
Watching external AV source (When the Interface board is installed.)
- When connecting the Plasma Monitor with external equipments, match the colours of connecting ports. - Or, connect the Euro scart socket of the VCR to the Euro scart socket of the set. 1. Press INPUT SELECT button on the remote control of the monitor to select AV or (AV1 or AV2). 2. Operate the corresponding external equipment. (See external equipment operating guide.)
Watching DVD (When the Interface board is installed.)
How to connect - Connect DVD video inputs to Y, PB, PR of COMPONENT (DVD INPUT) and audio inputs to Audio sockets of AUDIO INPUT. - Or, connect the Euro scart socket of the VCR to the Euro scart socket of the set. How to use 1. Press INPUT SELECT button on the remote control of the monitor to select Component or (AV1 or AV2). 2. Try this after turning on the DVD player. (Refer to the DVD player's manual for operating instructions.)
· Component Input ports You can get better picture quality if you connect DVD player with component input ports as below. Component ports of the Monitor Y Y Y Y Y PB PR
Video output ports of DVD player
Pr Pb B-Y R-Y Cb Cr PB PR
- 8 -
Watching DTV Setup (option)
- To watch digitally broadcast programs, purchase/connect a digital settop box. How to connect a user-supplied Digital Set-Top Box - Connect DTV set-top box video output to monitor COMPONENT (DVD/DTV INPUT) or to the monitor RGB (PC/DTV INPUT) or to the monitor DVI (PC/DTV INPUT) connector depending on your set-top box connectors. - Connect DTV set-top box audio outputs to monitor AUDIO INPUT jacks. How to use 1. Turn on the a digital set-top box. (Refer to the owner's manual for the digital set-top box) 2. Use INPUT SELECT on the remote control to select Component, RGB or DVI.
· DTV Input signal Mode Terminal Component RGB (DTV) DVI (DTV) o o o o o o o o o o o o
486p (60Hz) 576p (50Hz) 720p 1080i
Connecting PC
- To enjoy vivid picture and sound, connect a PC to the set. - Avoid keeping a fixed image on the set's screen for a long period of time. The fixed image may become permanently imprinted on the screen; use a screen saver when possible. - Connect PC to the RGB INPUT(PC INPUT) or DVI INPUT(DIGITAL RGB INPUT) port of the set; change the resolution output of PC accordingly. - There might be a noise according to some resolution, vertical pattern, contrast or brightness in PC mode. Then change the PC mode into other resolution or change the refresh rate into other rate or adjust the brightness and contrast on the menu until the picture is clean. If the refresh rate of the PC graphic card can not be changed, change the PC graphic card or consult it to the manufacturer of the PC graphic card. - The synchronization input form for Horizontal and Vertical frequencies is separate. Setup Instructions to Connect a PC to your set - We recommend using 1024x768, 60Hz for the PC mode, they provide the best picture quality. In MT/MZ-42PM10/11/20/21 series, we recommend using 640x480, 60Hz for the PC mode, they provide the best picture quality. - If the resolution of PC is over UXGA, there will be no picture on the set. - Connect the signal cable from the monitor output port of the PC to the RGB INPUT port of the set or the signal cable from the DVI output port of the PC to the DVI INPUT port on the set. - Connect the audio cable from the PC to the Audio input on the set. (Audio cables are not included with the set). - If using a sound card, adjust PC sound as required. - This set apply a VESA Plug and Play Solution. The set provides EDID data to the PC system with a DDC protocol. The PC adjusts automatically to use this set. - DDC protocol is preset for RGB (Analog RGB), DVI (Digital RGB) mode. - If required, adjust the set settings for Plug and Play functionally. - If graphic card on the PC does not output analog and digital RGB simultaneously, connect only one of both RGB INPUT or DVI INPUT to display the PC on the set. If graphic card on the PC does output analog and digital RGB simultaneously, set the set to either RGB or DVI; (the other mode is set to Plug and Play automatically by the set.) - DOS mode may not work depending on video card if using a DVI-I cable.
PC Setup 1. Turn on the PC and apply power to the set. 2. Turn on the display by pressing the POWER button on the set's remote control. 3. Use the INPUT SELECT or MULTIMEDIA button on the remote control to select the RGB or DVI input source. 4. Set the resolution output of the PC to SXGA or under (1280 x 1024, 60Hz). (Refer to p. 12)
- 9 -
Displayable Monitor Specification
RGB / DVI mode
Resolution 640x350 720x400 Horizontal Vertical Frequency(KHz) Frequency(Hz) 31.468 70.09 37.861 31.469 37.927 31.469 35.000 640x480 37.861 37.500 43.269 31.500 848x480 37.799 39.375 31.500 852x480 37.799 39.375 35.156 37.879 800x600 48.077 46.875 53.674 832x624 49.725 48.363 1024x768 56.476 60.023 68.677 1360x768 1366x768 47.700 59.625 47.700 59.625 54.348 1152x864 63.995 67.500 77.487 1152x870 1280x768 1280x960 1280x1024 68.681 47.693 60.091 68.504 60.023 63.981 85.08 70.08 85.03 59.94 66.66 72.80 75.00 85.00 60.00 70.00 75.00 60.00 70.00 75.00 56.25 60.31 72.18 75.00 85.06 74.55 60.00 70.06 75.02 85.00 60.00 75.02 60.00 75.02 60.05 70.01 75.00 85.00 75.06 60.00 75.00 85.00 60.02 60.02 1280x960 1280x1024 1280x768 1152x870 1152x864 1366x768 1360x768 1024x768 832x624 800x600 852x480 848x480 640x480
RGB / DVI mode
Resolution 640x350 720x400 Horizontal Vertical Frequency(KHz) Frequency(Hz) 31.468 70.09 37.861 31.469 37.927 31.469 35.000 37.861 37.500 43.269 31.500 37.799 39.375 31.500 37.799 39.375 35.156 37.879 48.077 46.875 53.674 49.725 48.363 56.476 60.023 68.677 47.700 59.625 68.500 47.700 59.625 69.500 54.348 63.995 67.500 77.487 68.681 47.693 60.091 68.504 60.023 63.981 85.08 70.08 85.03 59.94 66.66 72.80 75.00 85.00 60.00 70.00 75.00 60.00 70.00 75.00 56.25 (RGB) 60.31 72.18 75.00 85.06 74.55 60.00 70.06 75.02 85.00 60.00 75.02 85.00 60.00 75.02 85.00 60.05 70.01 75.00 85.00 75.06 60.00 75.00 85.00 60.02 60.02
MT/MZ-42PM10/11/20/21 series
MT/MZ-42PM12X series MT/MZ-50PM10/11/20/21 series
- 10 -
Accessories
MUTE POWER
PIP INPUT MULTIMEDIA INPUT SELECT EXIT ARC MENU
OK
VOL VOL
1 4 7 PSM
2 5 8 0
3 6 9 SSM
SLEEP
SPLIT ZOOM PIP/DW
WIN. SIZE POSITION
SWAP SCAN+ SKIP+ POWER
LG TV
AS mark
1.5V 1.5V
SCANSKIP-
PLAY STOP PAUSE
Owner's Manual
Alkaline batteries
Remote Control handset
Power Cord
BNC-RCA adapter (optional)
Optional Extras
Optional extras can be changed or modified for quality improvement without any notification new optional extras can be added. Contract your dealer for buying these items.
50
42
40
40
42
50
Tilt wall mounting bracket Ceiling mounting bracket
Desktop stand
Speakers
- 11 -
40
42
40
42
50
Installation Options
· The set can be installed in different ways such as on a wall, or on a desktop etc. · Install this set only in a location where adequate ventilation is available. · This set is designed so that it can be mounted either horizontally or vertically.
Wall Mount: Horizontal Installation
Wall Mount: Vertical Installation
· The set can be installed on a wall as shown above. (For further information, refer to the optional `Wall Mounting Bracket Installation and Setup Guide'.) · Speakers are optional, and are shown for illustration only.
Desktop Pedestal Installation
· The monitor can be installed vertically on the wall as shown above.(For further information, refer to the optional `Wall Mounting Bracket Installation and Setup Guide'.) Caution: When installing the monitor vertically, the front panel controls must be in the left-down side position as shown above. · Speakers are optional, and are shown for illustration only. · Note: To use the Monitor in a vertical orientation, the source's image must also be in a vertical format.
· The set can be mounted on a desk as shown above. (For further information, refer to the optional 'Desktop Stand Installation and Setup Guide'.) · Speakers and speaker stands shown are optional, and are shown for example only.
To Mount on a Wall Wall mount minimum allowable clearances for adequate ventilation.
10cm
To Install on a Desktop Pedestal mount minimum allowable clearances for adequate ventilation.
3cm
10cm
10cm
10cm
- 12 -
SPECIFICATIONS
NOTE : Specifications and others are subject to change without notice for improvement.
V
Application Range
This spec is sheet is applide to the 42",50" PDP TV used RF-04GA chassis. Chassis Model Name MZ-42PM10 MZ-42PM12X MZ-50PM10 MZ-50PM20 RF-04GA MT-42PM10 MT-42PM20 MT-42PM12X MT-50PM10 MT-50PM20 Non-EU LG Market Place EU Brand LG
V
Specification
Each part is tested as below without special appointment. 1) Temperature : 25¡ 5°C (77¡ 9°F) 2) Relative Humidity: 65¡ 10% 3) Power Voltage: Standard Input voltage (100V-240V~, 50/60Hz) * Standard Voltage of each product is marked by models. 4) Specification and performance of each parts are followed each drawing and specification by part number in accordance with BOM. 5) The receiver must be operated for about 20 minutes prior to the adjustment.
V
Test and Inspection Method
1) Performance : LGE TV test method followed. 2) Demanded other specification Safety: CE, IEC specification EMC : CE, IEC Model Name MZ-42PM10 MZ-42PM12X MZ-50PM10 MZ-50PM20 MT-42PM10 MT-42PM20 MT-42PM12X MT-50PM10 MT-50PM20 Non-EU Safety : IEC60065,IE60950 EMI : EN55022 Market EU Remark Safety : IEC60065 EMI EMS : EN55022 : EN55024
- 13 -
V
General Specification
1. General Specification (42" VGA MODULE) No 1 2 3 4 5 Item Display Screen Device Aspect Ratio PDP Module Screen Filter Operating Environment Specification 42 inch wide Color Display Module 16:9 PDP42V6000 45% Total light transmittance (E- Mesh) 1) Temp : 0~40 deg 2) Humidity : 0~85% 6 Storage Environment 1) Temp : -20~60 deg 2) Humidity : 0~85% 7 Input Voltage 100-240V~, 50/60Hz Maker : SONY / Murata / Sanken LGE SPEC LGE Maker : NBK / Mitsui / LG Chemical PDP Remark
2. General Specification (42" XGA MODULE) No 8 9 10 11 12 Item Display Screen Device Aspect Ratio PDP Module Screen Filter Operating Environment Specification 42 inch wide Color Display Module 16:9 PDP42X1A###, RGB Closed Type 45% Total light transmittance (E- Mesh) 1) Temp : 0~40 deg 2) Humidity : 0~85% 13 Storage Environment 1) Temp : -20~60 deg 2) Humidity : 0~85% 14 Input Voltage AC100 ~ 240V, 50/60Hz Maker : SONY / Sanken LGE SPEC Maker : NBK / Mitsui / LG Chemical PDP Remark
3. General Specification (50" XGA MODULE) No 15 16 17 18 19 Item Display Screen Device Aspect Ratio PDP Module Screen Filter Operating Environment Specification 50 inch wide Color Display Module 16:9 PDP50X2###, RGB Closed Type 45% Total light transmittance (E- Mesh) 1) Temp : 0~40 deg 2) Humidity : 0~85% 20 Storage Environment 1) Temp : -20~60 deg 2) Humidity : 0~85% 21 Input Voltage 100-240V~, 50/60Hz Maker : SONY / Sanken LGE SPEC LGE Maker : NBK / Mitsui / LG Chemical PDP Remark
- 14 -
V
Model Specification
1. MZ-42PM10 / 42PM12X / 50PM10 / 50PM20 No 22 23 Market Scart Jack (2EA ) Item EU PAL, SECAM 4 System : PAL, B/G/I/D/K, SECAM L/, NTSC4.43, PAL60 24 S-AV Input (1EA ) PAL, SECAM, NTSC 4 System : PAL, B/G/I/D/K, SECAM L/, NTSC4.43, PAL60 25 26 27 28 29 30 Component Input (1EA ) RGB Input (1EA ) RGB Outpu t (1EA ) DVI Input (1EA ) Audio Input (4EA ) Wired Control Y/ Cb/ Cr, Y/ Pb/ Pr RGB-PC/DTV RGB-PC/DTV DVI-PC/DTV PC Audio, Component,S-VHS, CVBS Discrete IR Up to UXGA@60Hz/480P Up to UXGA@60Hz/480P DVI-D L/R Input Specification Remark
2. MT-42PM10 / 42PM20 / 42PM12X / 50PM10 / 50PM20 No 31 32 Market Scart Jack (2EA ) Item Non-EU PAL, SECAM, NTSC 4 System : PAL, B/G/I/D/K, SECAM L/, NTSC4.43, PAL60 33 S-AV Input (1EA ) PAL, SECAM, NTSC 4 System : PAL, B/G/I/D/K, SECAM L/, NTSC4.43, PAL60 34 35 36 37 38 39 Component Input (1EA ) RGB Input (1EA ) RGB Outpu t (1EA ) DVI Input (1EA ) Audio Input (4EA ) Wired Control Y/ Cb/ Cr, Y/ Pb/ Pr RGB-PC/DTV RGB-PC/DTV DVI-PC/DTV PC Audio, Component,S-VHS, CVBS Discrete IR Up to UXGA@60Hz/480P Up to UXGA@60Hz/480P DVI-D L/R Input Specification Remark
- 15 -
ADJUSTMENT INSTRUCTIONS
1. Application Object
This spec sjeet os applied all of the 42", 50", RF-04GA chassis bymanufacturing LG TV Plant or sort plant.
Va Va GND GND Vs Vs Vs
Vs ADJ
VR551
P806
2. Specification
(1) Because this is not a hot chassis, it is not necessary to use an isolation transformer. However, the use of isolation transformer will help protect test instrument. (2) Adjustment must be done in the correct order. (3) The adjustment must be performed in the circumstance of 25±5°C of temperature and 65±10% of relative humidity if there is no specific designation. (4) The input voltage of the receiver must keep 100-220V~, 50/60Hz. (5) The receiver must be operated for about 15 minutes prior to the adjustment. After RGB Full white HEAT-RUN Mode, the receiver must be operated prior to adjustment. O Enter into HEAT-RUN MODE 1) Press the POWER ON KEY on R/C for adjustment. 2) OSD display and screen display 100% full WHITE PATTERN.
O
P805
P804
Vs ADJ
VR351
VR5
P803
P802
[ Set is activated HEAT-RUN without signal generator in this mode. [ Single color pattern(RED/BLUE/GREEN) of HEAT-RUN mode uses to check pannel. Caution) If you turn on a still screen more than 20 minutes (Especially digital pattern, cross hatch pattern), a after image may be occur in the black level part of the screen.
P801
[Fig. 1] Connection Diagram of Power Adjustment for Measuring
4. Auto RGB Color balance
4-1 Pattern Equipment : PC Pattern Generator( 801F or VG828 )
(16Gray Scale Pattern output(RGB output Level: 0.7Vp-p))
3. POWER PCB Assy Voltage Adjustments (Va, Vs Voltage Adjustments)
3-1. Test Equipment : D.M.M. 1EA 3-2. Connection Diagram for Measuring
Refer to [Fig 1]
4-2 Method of Auto RGB Color Balance
(1) Input RGB Source: 16Gray Scale Pattern output (RGB output Level: 0.7Vp-p) (2) Press ADJ KEY on R/C for adjustment. (3) Press Vol. +KEY and Operate To Set. (4) Auto-RGB OK means completed adjustment.
3-3. Adjustment Method for
(1) Va Adjustment
1) After receiving 100% Full White Pattern, HEAT RUN. 2) Connect + terminal of D.M.M to Va pin of P805, connect - terminal to GND pin of P805. 3) After turningVR351, voltage of D.M.M adjustment as same as Va voltage which on lable of panel right/top (Deviation; ±0.5V)
(2) Vs Adjustment
1) Connect + terminal of D.M.M to Vs pin of P805, connect terminal to GND pin of P805. 2) After turning RV551, voltage of D.M.M adjustment as same as Va voltage which on label of panel right/top. (Deviation; ±0.5V) [Fig. 2] Auto RGB Color Balance Test Pattern
- 16 -
4-3 Adjustment of White Balance
(1) Required Equipment Color Analyzer( CA-100 or same product) (2) Connecting diagram of equipment for measuring.
COL OR ANAL YZER TYPE; CA-100
5. DDC Data Input
5-1. Required Test Equipment
(1) A jig for adjusting PC, DDC (PC serial to D-sub Connection equipment) (2) S/W for writing DDC (EDID Data Write & Read) (3) D-sub 15P Cable, D-Sub to DVI Connector (Connect to DVI Jack)
High L ight Adj ustor (216 gr ay patter n)
AV Signal I nput
5-2. Setting of Device
Window
Pattern
PDP PC SET
MSPG-2100 or MSTG-5200
RS-232C Ser ial Communication
JIG
[Fig. 3] White Balance Adjustment
If you are adjusting a MZ Model, Use the RCA to SCART(Out) cable to input a AV signal.
5-3. Preparation for Adjustment
(3) Adjustment of White Balance O Operate the zero-calibration of the CA-100, then stick sensor to PDP module surface when you adjust.. O For manual adjustment, It is also possible by the following sequence. 1) Select white pattern of heat-run mode by pressing power on ket on remote control for adjustment then operate heat run more than 15 minute. 2) Supply Gray Pattern(216 Gray full window) signal to VIDEO input.(RZ-42PM10: AV4 input) refer to [fig3] 3) To adjust High Light, stick sensor to 216 Gray level pattern, press ADJ key twice(White Balance) on remote control. For adjustment and D/Eon remote control for adjustment mode to select Red Gain and Blue Gain, press Vol +.-key and adjust it ontil color coordination becomes as below. [RF-04GA:RZ-42PM10]: ¡ ¡ X; 0.283¡ æ0.003, Y; 0.297¡ æ0.003, ¡ Color Temperatuer;9,300 °K¡ æ500°K 4) Exit adjustment mode using V Key.
(1) Set devices as above and turn the PC, jig on. (2) Put S/W for writing DDC (EDID data Write & Read) into operation. (operated in DOS mode.)
5-4. Sequence of Adjustment
(1) DDC Data Input for Analog-RGB
1) Put the set on the table and turn the power on. 2) Connect PC Serial to D-sub 15P Cable of jig for DDC adjustment to RGB terminal (D-Sub 15Pin). 3) Operate S/W for DDC record and select DDC data for Analog RGB in Model Menu. 4) Operate EDID Write command. 5) Operate EDID Read command and check whether Check Sum is OK. 6) If Check Sum is NG, repeat 3) ~ 4). 7) If Check Sum is OK, DDC data for Analog-RGB input is completed.
(2) DDC Data input for Digital-RGB(DVI)
1) Connect PC Serial to DVI Cable of jig for DDC adjustment to DVI terminal (DVI Jack). 2) Operate S/W for DDC record and select DDC data for digital RGB in model menu. 3) Operate EDID Write command. 4) Operate EDID Read command and check whether Check sum is OK 5) If Check sum is NG, repeat 3) ~ 4). 6) If Check sum is OK, DDC data for Analog-RGB input is completed.
4-4 Auto Adjustment Map(RS-232C)
Type Baud Rate 115200 Index R Gain G Gain Protocol Setting B Gain R Offset G Offset B Offset Data bit 8 RF-043B_PDP42 Stop bit 1 Parity NONE
Cmd1 Cmd2 Data Min Value Max Value j j j j j j a b c d e f 00(00) 00(00) 00(00) 00(00) 00(00) 00(00) 255(FF) 255(FF) 255(FF) 255(FF) 255(FF) 255(FF)
- 17 -
TROUBLE SHOOTING GUIDE
1. Power Board
1-1. The whole flowchart which it follows in voltage output state
Start check
Doesn't the screen whole come out?
Yes
It is identical with Power Off condition? Yes
No
Is the Interface signal operated?
Yes 2. Check the Interface signal condition.
No
1. Check the Power Off condition.
Doesn't the low pressure output come out?
Yes
Doesn't the St-by 5V signal come out? Yes
No
Doesn't the 5V Monitor signal come out? Yes 4. Check the 5V Monitor signal circuit.
No
Doesn't the VSC signal RL-ON come out? Yes 5. Check the VSC RL-ON signal.
No
3. Check the St-by 5V signal circuit.
Doesn't the high tension output come out?
Yes
Doesn't the VSC signal Vs-ON come out? Yes
No
Doesn't the Vs, Va voltage output come out? Yes 8. Check the Vs, Va voltage output circuit.
Doesn't the VSC low pressure output come out? Yes 6. Check the VSC low pressure output
No
No
7. Check the VSC Vs-ON signal
High tension output voltage Drop it occurs?
Yes
When remove the Y, Z B/D Module Input Connector, Power Board high tension output voltage Drop it occurs? Yes 9. Check the Power Board Output high tension circuit
No
When remove the Y B/D Module Input Connector, output voltage Drop it occurs? Yes 10. Check the Z B/D Module Coutput circuit
No
When remove the Z B/D Module Input Connector, output voltage Drop it occurs? Yes 11. Check the Y B/D Module Coutput circuit
No
Manufacture enterprise meaning of a passage
- 18 -
1-2. Sony Power Board Structure
T502: Vs Trans T702: Va Trans
1
2
3
T101: St-by Trans T103: Low Voltage Trans
- 19 -
1-3. Sanken Power Board Structure
T221: Vs Trans T271: Va Trans
1
2
3
T121: St-by Trans T201: Low Voltage Trans
- 20 -
2. No Power
(1) Symptom
¯ ¯
Does't minute discharge at module. Non does not come in into the front LED.
(2) Check follow
No Is plug in power cord? Yes No Connect Cable. Plug in power cord.
Is connect the Line Filter and Power Switch Cable? Yes
Is connect the Power Switch and Power Board Cable? Yes
No Connect Cable.
Is normal the Fuse(F101) on Power Board? Yes
No Replace Fuse.
Is connect the Power Board and 7P of VSC Board Cable? Yes
No Connect Cable.
Is connect the Power Switch and Power Board Cable? Yes
No Connect Cable.
After remove the cable connect to Power Board(except the CN101 connection cable), authorizes the AC voltage marking on manual. When ST-BY 5V does not operate, replace Power Board.
- 21 -
3. Protect Mode
(1) Symptom
After once shining, it does not discharge minutely from module ¯ The Rely falls(The sound is audible "click") ¯ It is converted with the color where the front LED is red from green.
¯
(2) Check follow
Is normal the Power Board? Yes Is normal the each connector? Yes Is normal the Y- Board? Yes Is normal the Z- Board? Yes Is normal the X- Board? Yes Is normal the Ctrl Board? Yes Is normal the VSC Board? Yes Is normal the COF of X, Y, Z? No After crisis COF of each board, check the normality operates. If in case normality operates, correspondence COF Fail is replace the module. No Is normal the output voltage after remove P1000, P1200? Yes After remove P1000 normal operation: Replace Analog Board After remove P1200 normal operation: Replace Digital Board No Is normal the output voltage after remove P1, 2, 101, 300, 701, 702 connector of Ctrl-B/D? Yes Replace X-Board. No Is normal the output voltage after remove P1, 2, 3, 4, 6, 7 connector of X-B/D? Yes After remove P1, P2, P3, P4 output voltage normality: Replace Right X-B/D After remove P6, P7 output voltage normality: Replace Left X-B/D No Is normal the Fuse(FS1, FS2) on ZB/D? (In case of open is replace) Yes Is normal the output voltage after remove P1 connector of Z-B/D? Yes Replace Z-Board. No Is normal the Fuse(F52) on Y-B/D? (In case of open is replace) Yes Is normal the output voltage after remove P5, P6 connector of Y-B/D? Yes Replace Y-Board. No After connecting well each connector, the normality it operates? No Replace connector. No Is output the normality Low/High voltage except Stand-by 5V? No Replace Power Board.
- 22 -
4. No Raster
(1) Symptom
¯ ¯
Does't minute discharge at module. It maintains the condition where the front LED is green.
(2) Check follow
Is normal the Power Board? Yes Is normal the each connector? Yes Is normal the Y- Board? Yes Is normal the Z- Board? Yes Is normal the X- Board? Yes Is normal the Ctrl Board? Yes Is normal the VSC Board? Yes Is normal the COF of X, Y, Z? No After crisis COF of each board, check the normality operates. If in case normality operates, correspondence COF Fail is replace the module. No Is normal the output voltage after remove P403, P1300? Yes After remove P403 normal operation: Replace AV Fix Board After remove P1300 normal operation: Replace Digital Board No Is normal the output voltage after remove P1, 2, 101, 300, 701, 702 connector of Ctrl-B/D? Yes Replace X-Board. No Is normal the output voltage after remove P1, 2, 3, 4, 6, 7 connector of X-B/D? Yes After remove P1, P2, P3, P4 output voltage normality: Replace Right X-B/D After remove P6, P7 output voltage normality: Replace Left X-B/D No Is normal the Fuse(FS1, FS2) on ZB/D? (In case of open is replace) Yes Is normal the output voltage after remove P1 connector of Z-B/D? Yes Replace Z-Board. No Is normal the Fuse(F52) on Y-B/D? (In case of open is replace) Yes Is normal the output voltage after remove P5, P6 connector of Y-B/D? Yes Replace Y-Board. No After connecting well each connector, the normality it operates? No Replace connector. No Is output the normality Low/High voltage except Stand-by 5V? No Replace Power Board.
- 23 -
5. In case of occur strange screen into specific mode
5-1. In case of does't display the OSD
(1) Symptom
¯ ¯
LED is green The minute discharge continuously becomes accomplished from module
(2) Check follow
Is normal the LVDS cable? No Is the LVDS cable connected well? No Yes Replace cable.
Yes
Cable inserts well.
Is normal the VSC Digital Board?
No
Operates the Thine Yes IC(IC1200)? No
Operates the IEP(IC1100)? No
Yes
Operates the Scaler(IC900)? No
Yes
Replace VSC Digital B/D.
Yes
Replace Thine IC(IC1200).
Replace IEP(IC1100).
Replace Scaler(IC900).
Is normal the Ctrl Board of Module?
No Replace Ctrl B/D.
- 24 -
5-2. In case of does't display the screen into specific mode
(1) Symptom
¯
The screen does not become the display from specific input mode (RF, AV, Component, RGB, DVI).
(2) Check follow
¯ ¯
Check the all input mode should become normality display. Check the Video(Main)/Data(Sub), Video(Main)/Video(Sub) should become normality display from the PIP mode or DW mode. (Re-Check it Swap)
(3) In case of becomes unusual display from RF mode
No Is normal the Tuner? Is the Tuner Cable connected well? No Yes Cable inserts well. No No Replace IC Replace Tuner Yes Is normal the Input voltage, IIC Communication and CVBS output? No
Is normal the CXA2069Q? Yes Is normal the VPC3230?
Is normal the Input voltage, IIC Communication and HV sync?
No
Is normal the Input voltage, IIC Communication and HV sync?
No Replace IC
(4) In the case of becomes unusual display from RF, AV mode
Is normal the CXA2089Q? Yes Is normal the VPC3230? No Is normal the Input voltage, IIC Communication and HV sync? No Replace IC No Is normal the Input voltage, IIC Communication and HV sync? No Replace IC
- 25 -
(5) In the case of becomes unusual display from RF, AV, Component 480i mode
Is normal the VPC3230? Yes No Is normal the S2300? Yes No Is normal the Scaler? Is normal the Input voltage, IIC Communication and HV sync? No Replace IC Is normal the Input voltage, IIC Communication and HV sync? No Replace IC No Is normal the Input voltage, IIC Communication and HV sync? No Replace IC
(6) In the case of becomes unusual display from Component DTV mode
Is normal the 74LS123? Yes Is normal the CXA2101? Yes Is normal the M52758? Yes No Is normal the Scaler? Is normal the Input voltage, IIC Communication and HV sync? No Replace IC No Is normal the Input voltage, IIC Communication and HV sync? No Replace IC No Is normal the Input voltage, IIC Communication and HV sync? No Replace IC No Is normal the Input voltage, IIC Communication and HV sync? No Replace IC
- 26 -
(7) In the case of becomes unusual display from RGB DTV mode
Is normal the CXA2101? Yes Is normal the M52758? Yes No Is normal the Scaler? Is normal the Input voltage, IIC Communication and HV sync? No Replace IC No Is normal the Input voltage, IIC Communication and HV sync? No Replace IC No Is normal the Input voltage, IIC Communication and HV sync? No Replace IC
(8) In the case of becomes unusual display from RGB PC mode
Is normal the M52758? Yes No Is normal the Scaler? Is normal the Input voltage, IIC Communication and HV sync? No Replace IC No Is normal the Input voltage, IIC Communication and HV sync? No Replace IC
(8) In the case of becomes unusual display from DVI mode
No Is normal the Scaler? Is normal the Input voltage, IIC Communication and HV sync? No Replace IC
- 27 -
6. In case of no sound
(1) Symptom
¯ ¯
LED is green Screen display but sound is not output
(2) Check follow
Is normal the SPK cable? No Is the SPK cable connected well? No Yes Cable inserts well. Yes Replace SPK cable
Is normal the RGB/DVI sound?
No
Is the Flat cable connected well? No Cable inserts well.
Yes Operates the IC501? No Replace IC501
Yes Operates the IC502? No Replace IC502
Yes
Yes Is normal the RF/AV/Component sound? No Replace VSC Analog B/D
Operates the IC502? No Replace IC504
- 28 -
BLOCK DIAGRAM
Cable
- 29 -
BLOCK DIAGRAM
Cable
- 30 -
MEMO
- 31 -
EXPLODED VIEW
300
305 301
303
560 310 200 101 302 102
207
206 103 201 205 203 201
540
204 210 530 541 580
501 550 520 601
400
- 32 -
EXPLODED VIEW PARTS LIST
No.
101 103 103 200 201 202 203 204 205 206 207 210 300 301 302 303 305 310 400 501 520 530 540 541 550 560 580 601
Part No.
5900V06008B 4980V00D43A 4980V00C49A 6348Q-E062A 6871QCH038A 6871QDH068A 6871QDH069A 6871QLH037A 6871QRH043A 6871QYH030A 6871QZH034A 4980V00C62B 3091V00731H 4980V00C59B 4980V00C61G 4980V00C61F 3790V00709B 5020V01004A 3809V00504B 3301V00043B 6871VMMU20A 6871VSMAAUA 6871VSMABFA 5020V01009B 6871VSMAAVA 6871VSMT16A 3501V00182B 4980V00C71E
Description
FAN,DC G6015S12B2-RG DONGYANG 60*60*15 7V 1900RPM 6/12V L=500MM SUPPORTER, FAN SECC(EGI) MZ-42PM10 NCT SUPPORTER, FAN SECC(EGI) DULE MZ-42PM10 PDP, 42" 16:9 1024*768 PDP42X20000.ADLGA PWB(PCB) ASSEMBLY,DISPLAY CTRL ASSY HAND INSERT 42X2 CTRL LGDP4023,4013 PWB(PCB) ASSEMBLY,DISPLAY YDRV ASSY HAND INSERT 42X2 YDRV TOP PWB(PCB) ASSEMBLY,DISPLAY YDRV ASSY HAND INSERT 42X2 YDRV BOTTOM PWB(PCB) ASSEMBLY,DISPLAY XRLT ASSY HAND INSERT 42X2 X-LEFT(TCP) PWB(PCB) ASSEMBLY,DISPLAY XRRT ASSY HAND INSERT 42X2 X-RIGHT (TCP) PWB(PCB) ASSEMBLY,DISPLAY YSUS ASSY HAND INSERT FOR 42X2 PWB(PCB) ASSEMBLY,DISPLAY ZSUS ASSY HAND INSERT FOR 42X2 SUPPORTER, ASSY ZDC SUPP. MODULE VERTICAL C/SKD CABINET ASSEMBLY, 42PM12X RF043E 2TONE SKD SUPPORTER, ASSY EGI SUPP. FILTER TOP C/SKD SUPPORTER, ASSY EGI SUPP. FILTER LEFT APLLY TO MU-42PM12X SKD SUPPORTER, ASSY EGI SUPP. FILTER RIGHT APLLY TO MU-42PM12X SKD FILTER(MECH), MN42PZ41 LGM42-01 MITSUI 42"" ETCHING MESH GLASS FILTER" BUTTON, CONTROL 50PM10 6KEY BACK COVER ASSEMBLY, MZ-42PM10 C/SKD PLATE ASSEMBLY, ASSY 3301V00042A PLATE VSC ASSY C/SKD PWB(PCB) ASSEMBLY,MAIN RF-04GA 42INCH XGA VSC B/D PWB(PCB) ASSEMBLY,SUB A/V RF04GA RCA PAL PWB(PCB) ASSEMBLY,SUB PSW RF043A MAILBU BUTTON, POWER MZ-42PM10 ABS, AF-303S 1KEY C/SKD PWB(PCB) ASSEMBLY,SUB A/V RF04GA FIX B/D PWB(PCB) ASSEMBLY,SUB CONT RF04GA LOCAL KEY POWER SUPPLY ASSEMBLY, PDP 42INCH RF043B 450W APS-208/B SANKEN SUPPORTER, AV INTERFACE EGI MZ-42PM10 SKD
- 33 -
REPLACEMENT PARTS LIST
LOCA. NO PART NO DESCRIPTION LOCA. NO Q203 Q204 IC1100 IC503 IC901 IC1000 IC1001 IC101 IC200 IC801 IC902 IC100 IC1200 IC300 IC400 IC500 IC501 IC502 IC504 IC800 IC1504 IC201 IC506 IC700 IC900 IC1300 IC1301 IC1302 IC1400 IC1401 IC1402 IC1403 IC1404 IC1405 IC1501 IC1502 IC301 IC400 IC401 IC505 IC1503 IC202 IC401 0ICTMLG018A 0IKE704200J 0IKE704200J 0IMMRHY020B 0IMMRMR023B 0IMMRAL014B 0IMMRAL014B 0IMMRHY025C 0IMMRAL025A 0IMCRSG010A 0IMCRTH002A 0ISO208900A 0IMCRMI006A 0ISO210100B 0IMCRMN028B 0IMCRNL001A 0IMCRTI028C 0IMCRGN002C 0IPRPNS054A 0IPRPBB005A 0IPRPJR017A 0IIT323000E 0IPRPGN012A 0IPRPML001A 0IMCRSJ001A 0IMCRFA010A 0IMCRSH001A 0IMCRSH001A 0IMCRRH001A 0IPRPML001A 0IMCRRH001A 0IMCRSJ001A 0IMCRKE007A 0ISH122100B 0IMCRFA010A 0IMCRSH001A 0IPRPML001A 0IMCRFA010A 0IMCRPH015A 0IMCRTI003A 0ISTLSG009A LGDP4410 LG IC 176P TQFP KIA7042AF SOT-89 TP 4.2V VOLTAGE KIA7042AF SOT-89 TP 4.2V VOLTAGE HY5DU283222AQ-5 HYNIX 100P LQFP MX29LV800BTTC-70 MACRONIX 48P AT24C02N-10SI-2.7 ATMEL 8P SOIC AT24C02N-10SI-2.7 ATMEL 8P SOIC HY57V643220DT-6 HYNIX 86P/TSOP AT24C32AN-10SI-2.7 ATMEL 8PIN ST3232CDR SGS-THOMSON SOP16 THC63LVD103 THINE ELECTRONICS 64P CXA2089Q 48QFP BK A/V SWITCH M52758FP MITSUBISHI 36PIN, R/TP PLL IC CXA2101AQ 80P,QFP BK VIDEO MSP4410K MICRONAS 80P/PQFP NSP-6241B NEOFIDELITY 64P TQFP TAS5122DCAR 56P/TSSOP R/TP 30W FLI2300BD GENESIS 208P PQFP LM75CIMX-3 8P/SOP R/TP OPA3692IDBQ 16PIN SSOP NJU26901E2 JRC 8P,EMP R/TP VPC3230D C5 80P QFP GM1501HBD GENESIS 416P PBGA MIC39100 MICREL 3P SOT223 SC1565IST-1.8 3P SOT223 TP KA7809R, FAIRCHILD 2P D-PAK PQ05DZ1U SHARP 5, SMD TYPE PQ05DZ1U SHARP 5, SMD TYPE BA033FP-E2 ROHM 3P-SOP,TO252-3 MIC39100 MICREL 3P SOT223 BA033FP-E2 ROHM 3P-SOP,TO252-3 SC1565IST-1.8 SEMTECH 3P SOT223 TP KIA278R09PI KEC TO220IS,4P ST 2A PQ12RD21 4SIP ST REGULATOR KA7809R, FAIRCHILD 2P D-PAK PQ05DZ1U SHARP 5, SMD TYPE MIC39100 MICREL 3P SOT223 KA7809R, FAIRCHILD 2P D-PAK 74LVC32AD PHILIPS 14P SOT108-1 SN74HCT08D 16P R/TP QUADRUPLE M74HC123RM13TR 16P SOP Q300 Q300 Q301 Q301 Q302 Q302 Q303 Q303 Q304 Q304 Q305 Q305 Q306 Q306 Q307 Q307 Q308 Q308 Q309 Q309 Q310 Q311 Q312 Q313 Q400 Q401 Q402 Q403 Q405 Q407 Q100 Q101 Q200 Q201 Q404 Q406 Q502 Q503 Q504 PART NO 0TR387500AA 0TR387500AA 0TR387500AA 0TR387500AA 0TR387500AA 0TR387500AA 0TR387500AA 0TR387500AA 0TR387500AA 0TR387500AA 0TR387500AA 0TR387500AA 0TR387500AA 0TR387500AA 0TR387500AA 0TR387500AA 0TR387500AA 0TR387500AA 0TR387500AA 0TR387500AA 0TR387500AA 0TR387500AA 0TR387500AA 0TR387500AA 0TR387500AA 0TR387500AA 0TR387500AA 0TR387500AA 0TR387500AA 0TR387500AA 0TR387500AA 0TR387500AA 0TR830009BA 0TR830009BA 0TR830009BA 0TR830009BA 0TR150400BA 0TR104009AF 0TR150400BA 0TR150400BA 0TR150400BA DESCRIPTION CHIP 2SC3875S(ALY) KEC CHIP 2SC3875S(ALY) KEC CHIP 2SC3875S(ALY) KEC CHIP 2SC3875S(ALY) KEC CHIP 2SC3875S(ALY) KEC CHIP 2SC3875S(ALY) KEC CHIP 2SC3875S(ALY) KEC CHIP 2SC3875S(ALY) KEC CHIP 2SC3875S(ALY) KEC CHIP 2SC3875S(ALY) KEC CHIP 2SC3875S(ALY) KEC CHIP 2SC3875S(ALY) KEC CHIP 2SC3875S(ALY) KEC CHIP 2SC3875S(ALY) KEC CHIP 2SC3875S(ALY) KEC CHIP 2SC3875S(ALY) KEC CHIP 2SC3875S(ALY) KEC CHIP 2SC3875S(ALY) KEC CHIP 2SC3875S(ALY) KEC CHIP 2SC3875S(ALY) KEC CHIP 2SC3875S(ALY) KEC CHIP 2SC3875S(ALY) KEC CHIP 2SC3875S(ALY) KEC CHIP 2SC3875S(ALY) KEC CHIP 2SC3875S(ALY) KEC CHIP 2SC3875S(ALY) KEC CHIP 2SC3875S(ALY) KEC CHIP 2SC3875S(ALY) KEC CHIP 2SC3875S(ALY) KEC CHIP 2SC3875S(ALY) KEC CHIP 2SC3875S(ALY) KEC CHIP 2SC3875S(ALY) KEC BSS83 TP PHILIPS N-CHANNEL S/W TR BSS83 TP PHILIPS N-CHANNEL S/W TR BSS83 TP PHILIPS N-CHANNEL S/W TR BSS83 TP PHILIPS N-CHANNEL S/W TR CHIP 2SA1504S(ASY) KEC CHIP KRC104S SOT-23 TP KEC CHIP 2SA1504S(ASY) KEC CHIP 2SA1504S(ASY) KEC CHIP 2SA1504S(ASY) KEC
IC
DIODE
D1500 ZD100 0DD100009AM 0DR050008AA 0DR050008AA 0DR050008AA 0DR050008AA 0DR050008AA 0DR050008AA 0DR050008AA 0DD226239AA 0DD226239AA EU1ZV(1) TP SANKEN SD05.TC R/TP SEMTECH SOD323 5V 5A 15A SD05.TC R/TP SEMTECH SOD323 5V 5A 15A SD05.TC R/TP SEMTECH SOD323 5V 5A 15A SD05.TC R/TP SEMTECH SOD323 5V 5A 15A SD05.TC R/TP SEMTECH SOD323 5V 5A 15A SD05.TC R/TP SEMTECH SOD323 5V 5A 15A SD05.TC R/TP SEMTECH SOD323 5V 5A 15A CHIP KDS226 SOT-23 CHIP KDS226 SOT-23
TRANSISTOR
Q001 Q002 Q102 Q1300 Q1301 Q200 Q201 Q202 0TR387500AA 0TR387500AA 0TR387500AA 0TR387500AA 0TR387500AA 0TR387500AA 0TR387500AA 0TR387500AA CHIP 2SC3875S(ALY) KEC CHIP 2SC3875S(ALY) KEC CHIP 2SC3875S(ALY) KEC CHIP 2SC3875S(ALY) KEC CHIP 2SC3875S(ALY) KEC CHIP 2SC3875S(ALY) KEC CHIP 2SC3875S(ALY) KEC CHIP 2SC3875S(ALY) KEC
ZD101 ZD102 ZD200 ZD201 ZD202 ZD203 D100 D101
- 34 -
For Capacitor & Resistors, the charactors at 2nd and 3rd digit in the P/No. means as follows;
CC, CX, CK, CN : Ceramic CQ : Polyestor CE : Electrolytic
RD : Carbon Film RS : Metal Oxide Film RN : Metal Film RF : Fusible
LOCA. NO D102 D103 D104 D105 D106 D107 D108 D1304 D1305 D1306 D1400 D1401 D1402 D1403 D1404 D1405 D200 D200 D201 D201 D202 D202 D203 D204 D205 D206 D207 D208 D209 D210 D211 D212 D213 D214 D215 D216 D217 D218 D219 D220 D221 D222 D300 D301 D302 D303 D304 D305 D306 D307 D308 D309
PART NO 0DD226239AA 0DD226239AA 0DD226239AA 0DD226239AA 0DD226239AA 0DD226239AA 0DD184009AA 0DD226239AA 0DD226239AA 0DD226239AA 0DD226239AA 0DD226239AA 0DD226239AA 0DD226239AA 0DD226239AA 0DD226239AA 0DD226239AA 0DD226239AA 0DD226239AA 0DD226239AA 0DD226239AA 0DD226239AA 0DD226239AA 0DD226239AA 0DD226239AA 0DD226239AA 0DD226239AA 0DD226239AA 0DD226239AA 0DD226239AA 0DD226239AA 0DD226239AA 0DD226239AA 0DD226239AA 0DD226239AA 0DD226239AA 0DD226239AA 0DD226239AA 0DD226239AA 0DD226239AA 0DD226239AA 0DD226239AA 0DD226239AA 0DD226239AA 0DD226239AA 0DD226239AA 0DD226239AA 0DD226239AA 0DD226239AA 0DD226239AA 0DD226239AA 0DD226239AA
DESCRIPTION CHIP KDS226 SOT-23 CHIP KDS226 SOT-23 CHIP KDS226 SOT-23 CHIP KDS226 SOT-23 CHIP KDS226 SOT-23 CHIP KDS226 SOT-23 KDS184S CHIP 85V 300MA KEC TP CHIP KDS226 SOT-23 CHIP KDS226 SOT-23 CHIP KDS226 SOT-23 CHIP KDS226 SOT-23 CHIP KDS226 SOT-23 CHIP KDS226 SOT-23 CHIP KDS226 SOT-23 CHIP KDS226 SOT-23 CHIP KDS226 SOT-23 CHIP KDS226 SOT-23 CHIP KDS226 SOT-23 CHIP KDS226 SOT-23 CHIP KDS226 SOT-23 CHIP KDS226 SOT-23 CHIP KDS226 SOT-23 CHIP KDS226 SOT-23 CHIP KDS226 SOT-23 CHIP KDS226 SOT-23 CHIP KDS226 SOT-23 CHIP KDS226 SOT-23 CHIP KDS226 SOT-23 CHIP KDS226 SOT-23 CHIP KDS226 SOT-23 CHIP KDS226 SOT-23 CHIP KDS226 SOT-23 CHIP KDS226 SOT-23 CHIP KDS226 SOT-23 CHIP KDS226 SOT-23 CHIP KDS226 SOT-23 CHIP KDS226 SOT-23 CHIP KDS226 SOT-23 CHIP KDS226 SOT-23 CHIP KDS226 SOT-23 CHIP KDS226 SOT-23 CHIP KDS226 SOT-23 CHIP KDS226 SOT-23 CHIP KDS226 SOT-23 CHIP KDS226 SOT-23 CHIP KDS226 SOT-23 CHIP KDS226 SOT-23 CHIP KDS226 SOT-23 CHIP KDS226 SOT-23 CHIP KDS226 SOT-23 CHIP KDS226 SOT-23 CHIP KDS226 SOT-23
LOCA. NO D310 D400 D401 D402 ZD500
PART NO 0DD226239AA 0DD226239AA 0DD226239AA 0DD226239AA 0DZ820009AH
DESCRIPTION CHIP KDS226 SOT-23 CHIP KDS226 SOT-23 CHIP KDS226 SOT-23 CHIP KDS226 SOT-23 MTZJ8.2B TP ROHM-K DO34 - 8.2V 5UA
CAPACITOR
C404 C410 C553 C554 C569 C002 C1000 C1001 C1019 C115 C1300 C1305 C1306 C1308 C1318 C1322 C1323 C1325 C1326 C1330 C1331 C1332 C1335 C1336 C1338 C1351 C1354 C1355 C1356 C1402 C1403 C1418 C1419 C1420 C1422 C1423 C1424 C1427 C1428 C1441 C1443 C1444 C1445 C1446 C1450 0CE108DJ618 0CE108DJ618 0CE108DH618 0CE108DH618 0CE108DH618 0CE476SF6DC 0CE226SF6DC 0CE226SF6DC 0CE107SF6DC 0CE476SF6DC 0CE477SF6DC 0CE227VF6DC 0CE227VF6DC 0CE477SF6DC 0CE477SF6DC 0CE477SF6DC 0CE477SF6DC 0CE227VF6DC 0CE477SF6DC 0CE227VF6DC 0CE227VF6DC 0CE107SF6DC 0CE227VF6DC 0CE227VF6DC 0CE107SF6DC 0CE476SF6DC 0CE107SF6DC 0CE107SF6DC 0CE476SF6DC 0CE477SF6DC 0CE227VF6DC 0CE107SF6DC 0CE107SF6DC 0CE107SF6DC 0CE107SF6DC 0CE107SF6DC 0CE476SF6DC 0CE477SF6DC 0CE227VF6DC 0CE107SF6DC 0CE107SF6DC 0CE107SF6DC 0CE107SF6DC 0CE107SF6DC 0CE477SF6DC 1000UF STD 35V M FL TP5 1000UF STD 35V M FL TP5 1000UF STD 25V M FL TP5 1000UF STD 25V M FL TP5 1000UF STD 25V M FL TP5 47UF MVG 16V M SMD R/TP 22UF MVG 16V 20% SMD R/TP 22UF MVG 16V 20% SMD R/TP 100UF MVG 16V M SMD R/TP 47UF MVG 16V M SMD R/TP 470UF MVG 16V 20% R/TP(SMD) SMD 220UF MV 16V 20% R/TP(SMD) SMD 220UF MV 16V 20% R/TP(SMD) SMD 470UF MVG 16V 20% R/TP(SMD) SMD 470UF MVG 16V 20% R/TP(SMD) SMD 470UF MVG 16V 20% R/TP(SMD) SMD 470UF MVG 16V 20% R/TP(SMD) SMD 220UF MV 16V 20% R/TP(SMD) SMD 470UF MVG 16V 20% R/TP(SMD) SMD 220UF MV 16V 20% R/TP(SMD) SMD 220UF MV 16V 20% R/TP(SMD) SMD 100UF MVG 16V M SMD R/TP 220UF MV 16V 20% R/TP(SMD) SMD 220UF MV 16V 20% R/TP(SMD) SMD 100UF MVG 16V M SMD R/TP 47UF MVG 16V M SMD R/TP 100UF MVG 16V M SMD R/TP 100UF MVG 16V M SMD R/TP 47UF MVG 16V M SMD R/TP 470UF MVG 16V 20% R/TP(SMD) SMD 220UF MV 16V 20% R/TP(SMD) SMD 100UF MVG 16V M SMD R/TP 100UF MVG 16V M SMD R/TP 100UF MVG 16V M SMD R/TP 100UF MVG 16V M SMD R/TP 100UF MVG 16V M SMD R/TP 47UF MVG 16V M SMD R/TP 470UF MVG 16V 20% R/TP(SMD) SMD 220UF MV 16V 20% R/TP(SMD) SMD 100UF MVG 16V M SMD R/TP 100UF MVG 16V M SMD R/TP 100UF MVG 16V M SMD R/TP 100UF MVG 16V M SMD R/TP 100UF MVG 16V M SMD R/TP 470UF MVG 16V 20% R/TP(SMD) SMD
- 35 -
For Capacitor & Resistors, the charactors at 2nd and 3rd digit in the P/No. means as follows;
CC, CX, CK, CN : Ceramic CQ : Polyestor CE : Electrolytic
RD : Carbon Film RS : Metal Oxide Film RN : Metal Film RF : Fusible
LOCA. NO C1451 C1452 C1456 C1457 C1458 C1481 C1482 C1483 C1484 C1485 C1487 C1489 C1490 C1491 C1493 C1501 C1514 C1516 C1517 C1518 C1519 C200 C210 C211 C211 C212 C212 C213 C214 C215 C216 C219 C220 C221 C221 C223 C224 C225 C227 C239 C240 C241 C242 C248 C249 C250 C300 C300 C301 C302 C303 C304
PART NO 0CE477SF6DC 0CE476SF6DC 0CE476SF6DC 0CE477SF6DC 0CE477SF6DC 0CE107SF6DC 0CE476SF6DC 0CE476SF6DC 0CE476SF6DC 0CE476SF6DC 0CE476SF6DC 0CE476SF6DC 0CE476SF6DC 0CE476SF6DC 0CE477SF6DC 0CE476SF6DC 0CE476SF6DC 0CE227VF6DC 0CE105SK6DC 0CE105SK6DC 0CE105SK6DC 0CE477VF6DC 0CE476SF6DC 0CE107SF6DC 0CE476SF6DC 0CE107SF6DC 0CE476SF6DC 0CE107SF6DC 0CE107SF6DC 0CE107SF6DC 0CE107SF6DC 0CE476SF6DC 0CE475WJ6DC 0CE107SF6DC 0CE475WJ6DC 0CE477SF6DC 0CE476SF6DC 0CE477SF6DC 0CE477SF6DC 0CE105SK6DC 0CE105SK6DC 0CE105SK6DC 0CE105SK6DC 0CE475WJ6DC 0CE475WJ6DC 0CE477VF6DC 0CE476SF6DC 0CE105SK6DC 0CE105SK6DC 0CE105SK6DC 0CE105SK6DC 0CE105SK6DC
DESCRIPTION 470UF MVG 16V 20% R/TP(SMD) SMD 47UF MVG 16V M SMD R/TP 47UF MVG 16V M SMD R/TP 470UF MVG 16V 20% R/TP(SMD) SMD 470UF MVG 16V 20% R/TP(SMD) SMD 100UF MVG 16V M SMD R/TP 47UF MVG 16V M SMD R/TP 47UF MVG 16V M SMD R/TP 47UF MVG 16V M SMD R/TP 47UF MVG 16V M SMD R/TP 47UF MVG 16V M SMD R/TP 47UF MVG 16V M SMD R/TP 47UF MVG 16V M SMD R/TP 47UF MVG 16V M SMD R/TP 470UF MVG 16V 20% R/TP(SMD) SMD 47UF MVG 16V M SMD R/TP 47UF MVG 16V M SMD R/TP 220UF MV 16V 20% R/TP(SMD) SMD 1UF MVG 50V M SMD R/TP 1UF MVG 50V M SMD R/TP 1UF MVG 50V M SMD R/TP 470UF MV 16V 20% R/TP(SMD) SMD 47UF MVG 16V M SMD R/TP 100UF MVG 16V M SMD R/TP 47UF MVG 16V M SMD R/TP 100UF MVG 16V M SMD R/TP 47UF MVG 16V M SMD R/TP 100UF MVG 16V M SMD R/TP 100UF MVG 16V M SMD R/TP 100UF MVG 16V M SMD R/TP 100UF MVG 16V M SMD R/TP 47UF MVG 16V M SMD R/TP 4.7UF MVK 35V 20% R/TP(SMD) SMD 100UF MVG 16V M SMD R/TP 4.7UF MVK 35V 20% R/TP(SMD) SMD 470UF MVG 16V 20% R/TP(SMD) SMD 47UF MVG 16V M SMD R/TP 470UF MVG 16V 20% R/TP(SMD) SMD 470UF MVG 16V 20% R/TP(SMD) SMD 1UF MVG 50V M SMD R/TP 1UF MVG 50V M SMD R/TP 1UF MVG 50V M SMD R/TP 1UF MVG 50V M SMD R/TP 4.7UF MVK 35V 20% R/TP(SMD) SMD 4.7UF MVK 35V 20% R/TP(SMD) SMD 470UF MV 16V 20% R/TP(SMD) SMD 47UF MVG 16V M SMD R/TP 1UF MVG 50V M SMD R/TP 1UF MVG 50V M SMD R/TP 1UF MVG 50V M SMD R/TP 1UF MVG 50V M SMD R/TP 1UF MVG 50V M SMD R/TP
LOCA. NO C305 C305 C308 C309 C310 C313 C314 C315 C319 C335 C336 C337 C339 C343 C344 C345 C347 C400 C404 C405 C406 C406 C407 C408 C409 C411 C412 C415 C416 C417 C418 C420 C423 C426 C427 C429 C431 C434 C437 C500 C501 C506 C507 C513 C514 C515 C516 C517 C517 C522 C525 C530
PART NO 0CE476SF6DC 0CE105SK6DC 0CE105SK6DC 0CE476SF6DC 0CE105SK6DC 0CE105SK6DC 0CE105SK6DC 0CE105SK6DC 0CE105SK6DC 0CE476SF6DC 0CE476SF6DC 0CE476SF6DC 0CE476SF6DC 0CE476SF6DC 0CE476SF6DC 0CE476SF6DC 0CE476SF6DC 0CE476SF6DC 0CE476SF6DC 0CE476SF6DC 0CE476SF6DC 0CE227VF6DC 0CE477SF6DC 0CE477SF6DC 0CE477SF6DC 0CE227VF6DC 0CE476XFKDC 0CE476XFKDC 0CE476XFKDC 0CE227VF6DC 0CE106SF6DC 0CE107SF6DC 0CE476SF6DC 0CE477SF6DC 0CE107SF6DC 0CE107SF6DC 0CE477SF6DC 0CE476SF6DC 0CE107SF6DC 0CE476SF6DC 0CE476SF6DC 0CE335SK6DC 0CE335SK6DC 0CE106SF6DC 0CE106SF6DC 0CE107SF6DC 0CE105SK6DC 0CE107SF6DC 0CE226SF6DC 0CE107SF6DC 0CE226VF6DC 0CE107SF6DC
DESCRIPTION 47UF MVG 16V M SMD R/TP 1UF MVG 50V M SMD R/TP 1UF MVG 50V M SMD R/TP 47UF MVG 16V M SMD R/TP 1UF MVG 50V M SMD R/TP 1UF MVG 50V M SMD R/TP 1UF MVG 50V M SMD R/TP 1UF MVG 50V M SMD R/TP 1UF MVG 50V M SMD R/TP 47UF MVG 16V M SMD R/TP 47UF MVG 16V M SMD R/TP 47UF MVG 16V M SMD R/TP 47UF MVG 16V M SMD R/TP 47UF MVG 16V M SMD R/TP 47UF MVG 16V M SMD R/TP 47UF MVG 16V M SMD R/TP 47UF MVG 16V M SMD R/TP 47UF MVG 16V M SMD R/TP 47UF MVG 16V M SMD R/TP 47UF MVG 16V M SMD R/TP 47UF MVG 16V M SMD R/TP 220UF MV 16V 20% R/TP(SMD) SMD 470UF MVG 16V 20% R/TP(SMD) SMD 470UF MVG 16V 20% R/TP(SMD) SMD 470UF MVG 16V 20% R/TP(SMD) SMD 220UF MV 16V 20% R/TP(SMD) SMD 47UF MVK-BP,CN 16V 20%,-20% SMD 47UF MVK-BP,CN 16V 20%,-20% SMD 47UF MVK-BP,CN 16V 20%,-20% SMD 220UF MV 16V 20% R/TP(SMD) SMD 10UF MVG 16V 20% R/TP(SMD) SMD 100UF MVG 16V M SMD R/TP 47UF MVG 16V M SMD R/TP 470UF MVG 16V 20% R/TP(SMD) SMD 100UF MVG 16V M SMD R/TP 100UF MVG 16V M SMD R/TP 470UF MVG 16V 20% R/TP(SMD) SMD 47UF MVG 16V M SMD R/TP 100UF MVG 16V M SMD R/TP 47UF MVG 16V M SMD R/TP 47UF MVG 16V M SMD R/TP 3.3UF MVG 50V 20% SMD R/TP 3.3UF MVG 50V 20% SMD R/TP 10UF MVG 16V 20% R/TP(SMD) SMD 10UF MVG 16V 20% R/TP(SMD) SMD 100UF MVG 16V M SMD R/TP 1UF MVG 50V M SMD R/TP 100UF MVG 16V M SMD R/TP 22UF MVG 16V 20% SMD R/TP 100UF MVG 16V M SMD R/TP 22UF MV 16V 20% R/TP(SMD) SMD 100UF MVG 16V M SMD R/TP
- 36 -
For Capacitor & Resistors, the charactors at 2nd and 3rd digit in the P/No. means as follows;
CC, CX, CK, CN : Ceramic CQ : Polyestor CE : Electrolytic
RD : Carbon Film RS : Metal Oxide Film RN : Metal Film RF : Fusible
LOCA. NO C534 C536 C538 C540 C705 C709 C714 C730 C827 C833 C904 C905 C906 C908 C909 C910 C911 C912 C913 C919 C920 C921 C567 C568 C411 C545 C549
PART NO 0CE106SF6DC 0CE106SF6DC 0CE106SF6DC 0CE106SF6DC 0CE107SF6DC 0CE106SF6DC 0CE106SF6DC 0CE106SF6DC 0CE107SF6DC 0CE107SF6DC 0CE335SK6DC 0CE226SF6DC 0CE226SF6DC 0CE226SF6DC 0CE226SF6DC 0CE226SF6DC 0CE226SF6DC 0CE226SF6DC 0CE226SF6DC 0CE226SF6DC 0CE226SF6DC 0CE226SF6DC 0CF4741L438 0CF4741L438 0CN105EJ56A 0CN105EJ56A 0CN105EJ56A
DESCRIPTION 10UF MVG 16V 20% R/TP(SMD) SMD 10UF MVG 16V 20% R/TP(SMD) SMD 10UF MVG 16V 20% R/TP(SMD) SMD 10UF MVG 16V 20% R/TP(SMD) SMD 100UF MVG 16V M SMD R/TP 10UF MVG 16V 20% R/TP(SMD) SMD 10UF MVG 16V 20% R/TP(SMD) SMD 10UF MVG 16V 20% R/TP(SMD) SMD 100UF MVG 16V M SMD R/TP 100UF MVG 16V M SMD R/TP 3.3UF MVG 50V 20% SMD R/TP 22UF MVG 16V 20% SMD R/TP 22UF MVG 16V 20% SMD R/TP 22UF MVG 16V 20% SMD R/TP 22UF MVG 16V 20% SMD R/TP 22UF MVG 16V 20% SMD R/TP 22UF MVG 16V 20% SMD R/TP 22UF MVG 16V 20% SMD R/TP 22UF MVG 16V 20% SMD R/TP 22UF MVG 16V 20% SMD R/TP 22UF MVG 16V 20% SMD R/TP 22UF MVG 16V 20% SMD R/TP 0.47UF D 63V 5% TP 5 M/PE NI 0.47UF D 63V 5% TP 5 M/PE NI 1.0UF 3216 35V 10% R/TP X7R 1.0UF 3216 35V 10% R/TP X7R 1.0UF 3216 35V 10% R/TP X7R
LOCA. NO RA1101 RA1102 RA1103 RA1104 RA1105 RA1106 RA700 RA701 RA702 RA703 RA800 RA801 RA803 RA805 RA806 RA807 RA808 RA809 RA810 RA811 RA812 RA813 RA814 RA815 RA816 RA817 RA818 RA900 RA901 RA902 RA903 RA904 RA905 RA906 RA907 RA908 RA909 RA910 RA911 RA912
PART NO 0RRZVTA001D 0RRZVTA001D 0RRZVTA001D 0RRZVTA001D 0RRZVTA001D 0RRZVTA001D 0RRZVTA001D 0RRZVTA001D 0RRZVTA001D 0RRZVTA001D 0RRZVTA001D 0RRZVTA001D 0RRZVTA001D 0RRZVTA001D 0RRZVTA001D 0RRZVTA001D 0RRZVTA001D 0RRZVTA001D 0RRZVTA001D 0RRZVTA001D 0RRZVTA001D 0RRZVTA001D 0RRZVTA001D 0RRZVTA001D 0RRZVTA001D 0RRZVTA001D 0RRZVTA001D 0RRZVTA001D 0RRZVTA001D 0RRZVTA001D 0RRZVTA001D 0RRZVTA001D 0RRZVTA001D 0RRZVTA001D 0RRZVTA001D 0RRZVTA001D 0RRZVTA001D 0RRZVTA001D 0RRZVTA001D 0RRZVTA001D
DESCRIPTION 22 OHM 1 / 16 W 1608 5% R/TP 4P E24 22 OHM 1 / 16 W 1608 5% R/TP 4P E24 22 OHM 1 / 16 W 1608 5% R/TP 4P E24 22 OHM 1 / 16 W 1608 5% R/TP 4P E24 22 OHM 1 / 16 W 1608 5% R/TP 4P E24 22 OHM 1 / 16 W 1608 5% R/TP 4P E24 22 OHM 1 / 16 W 1608 5% R/TP 4P E24 22 OHM 1 / 16 W 1608 5% R/TP 4P E24 22 OHM 1 / 16 W 1608 5% R/TP 4P E24 22 OHM 1 / 16 W 1608 5% R/TP 4P E24 22 OHM 1 / 16 W 1608 5% R/TP 4P E24 22 OHM 1 / 16 W 1608 5% R/TP 4P E24 22 OHM 1 / 16 W 1608 5% R/TP 4P E24 22 OHM 1 / 16 W 1608 5% R/TP 4P E24 22 OHM 1 / 16 W 1608 5% R/TP 4P E24 22 OHM 1 / 16 W 1608 5% R/TP 4P E24 22 OHM 1 / 16 W 1608 5% R/TP 4P E24 22 OHM 1 / 16 W 1608 5% R/TP 4P E24 22 OHM 1 / 16 W 1608 5% R/TP 4P E24 22 OHM 1 / 16 W 1608 5% R/TP 4P E24 22 OHM 1 / 16 W 1608 5% R/TP 4P E24 22 OHM 1 / 16 W 1608 5% R/TP 4P E24 22 OHM 1 / 16 W 1608 5% R/TP 4P E24 22 OHM 1 / 16 W 1608 5% R/TP 4P E24 22 OHM 1 / 16 W 1608 5% R/TP 4P E24 22 OHM 1 / 16 W 1608 5% R/TP 4P E24 22 OHM 1 / 16 W 1608 5% R/TP 4P E24 22 OHM 1 / 16 W 1608 5% R/TP 4P E24 22 OHM 1 / 16 W 1608 5% R/TP 4P E24 22 OHM 1 / 16 W 1608 5% R/TP 4P E24 22 OHM 1 / 16 W 1608 5% R/TP 4P E24 22 OHM 1 / 16 W 1608 5% R/TP 4P E24 22 OHM 1 / 16 W 1608 5% R/TP 4P E24 22 OHM 1 / 16 W 1608 5% R/TP 4P E24 22 OHM 1 / 16 W 1608 5% R/TP 4P E24 22 OHM 1 / 16 W 1608 5% R/TP 4P E24 22 OHM 1 / 16 W 1608 5% R/TP 4P E24 22 OHM 1 / 16 W 1608 5% R/TP 4P E24 22 OHM 1 / 16 W 1608 5% R/TP 4P E24 22 OHM 1 / 16 W 1608 5% R/TP 4P E24
COIL
L1300 L1301 L1302 L1303 L400 L401 L402 L507 L508 L509 L510 6140VB0004B 6140VB0004B 6140VB0004B 6140VB0004B 6140VB0004B 6140VB0004B 6140VB0004B 6140VB0024A 6140VB0024A 6140VB0024A 6140VB0024A 26UH 1UEWPHY 22.5TURN YL-9N 0.4 26UH 1UEWPHY 22.5TURN YL-9N 0.4 26UH 1UEWPHY 22.5TURN YL-9N 0.4 26UH 1UEWPHY 22.5TURN YL-9N 0.4 26UH 1UEWPHY 22.5TURN YL-9N 0.4 26UH 1UEWPHY 22.5TURN YL-9N 0.4 26UH 1UEWPHY 22.5TURN YL-9N 0.4 LPK-1322A SOOJUNG 22UH +-10% LPK-1322A SOOJUNG 22UH +-10% LPK-1322A SOOJUNG 22UH +-10% LPK-1322A SOOJUNG 22UH +-10%
CONNECTOR
P101 P200 P201 P500 6630VGA004B 6630VGA001C 6630VGA001C 385-173B 69107-0921 9P 2.77MM 68114-1521 15PIN 2.29MM ANGLE SN 68114-1521 15PIN 2.29MM ANGLE SN VER TYPE(2LINE 4P A+B) D1301 D1302 D1303 LD001 LED400 LED401 LED402 0DL233309AC 0DL233309AC 0DL233309AC 0DL200000CA 0DL233309AC 0DL233309AC 0DL233309AC
LED
SAM2333 GREEN/RED GREEN:10MCD, RED:6MCD SAM2333 GREEN/RED GREEN:10MCD, RED:6MCD SAM2333 GREEN/RED GREEN:10MCD, RED:6MCD SAM5670(DL-2LRG) BK Y-GREEN SAM2333 GREEN/RED GREEN:10MCD, RED:6MCD SAM2333 GREEN/RED GREEN:10MCD, RED:6MCD SAM2333 GREEN/RED GREEN:10MCD, RED:6MCD
RESISTOR
R1530 R801 R802 RA1100 0RD0152H609 0RKZVTA001L 0RKZVTA001L 0RRZVTA001D 15 OHM 1/2 W 5.00% TA52 1.0M OHM 1/2 W 5% TA52 UL PILKOR 1.0M OHM 1/2 W 5% TA52 UL PILKOR 22 OHM 1 / 16 W 1608 5% R/TP 4P E24
SWITCH
SW001 140-313B TACT 2LEAD 160G(TA) LG C&D
- 37 -
LOCA. NO SW002 SW003 SW004 SW005 SW006 SW800 SW900
PART NO 140-313B 140-313B 140-313B 140-313B 140-313B 6600VM2006A 140-313B
DESCRIPTION TACT 2LEAD 160G(TA) LG C&D TACT 2LEAD 160G(TA) LG C&D TACT 2LEAD 160G(TA) LG C&D TACT 2LEAD 160G(TA) LG C&D TACT 2LEAD 160G(TA) LG C&D SDDF3PATP011 250V 4A HORIZONTAL .G TACT 2LEAD 160G(TA) LG C&D
LOCA. NO L1428 L201 L205 L209 L210 L303 L304 L305 L401 L402 L403 L404 L405 L406 L407 L500 L501 L502 L503 L504 L504 L505 L505 L506 L900 X500 X700 X800 X900
PART NO 6210VC0006A 6210VC0006A 6210VC0005A 6210VC0006A 6210VC0006A 6210VC0006A 6210VC0006A 6210VC0006A 6210VC0006A 6210VC0006A 6210VC0006A 6210VC0006A 6210VC0006A 6210VC0006A 6210VC0006A 6210VC0006A 6210VC0006A 6210VC0006A 6210VC0006A 6200JB8010L 6210VC0005A 6200JB8010L 6210VC0005A 6210VC0005A 6210VC0006A 156-A02M 6202VDT002E 6202VDT002J 6202VDT002B
DESCRIPTION FBMH3216 HM501NT 3.2X1.6X1.6MM R/TP FBMH3216 HM501NT 3.2X1.6X1.6MM R/TP BK2125 HS 750 2X1.25X0.85MM R/TP FBMH3216 HM501NT 3.2X1.6X1.6MM R/TP FBMH3216 HM501NT 3.2X1.6X1.6MM R/TP FBMH3216 HM501NT 3.2X1.6X1.6MM R/TP FBMH3216 HM501NT 3.2X1.6X1.6MM R/TP FBMH3216 HM501NT 3.2X1.6X1.6MM R/TP FBMH3216 HM501NT 3.2X1.6X1.6MM R/TP FBMH3216 HM501NT 3.2X1.6X1.6MM R/TP FBMH3216 HM501NT 3.2X1.6X1.6MM R/TP FBMH3216 HM501NT 3.2X1.6X1.6MM R/TP FBMH3216 HM501NT 3.2X1.6X1.6MM R/TP FBMH3216 HM501NT 3.2X1.6X1.6MM R/TP FBMH3216 HM501NT 3.2X1.6X1.6MM R/TP FBMH3216 HM501NT 3.2X1.6X1.6MM R/TP FBMH3216 HM501NT 3.2X1.6X1.6MM R/TP FBMH3216 HM501NT 3.2X1.6X1.6MM R/TP FBMH3216 HM501NT 3.2X1.6X1.6MM R/TP MLB-201209-1000L-N2 R/TP 1000OHM 350MA BK2125 HS 750 2X1.25X0.85MM R/TP MLB-201209-1000L-N2 R/TP 1000OHM 350MA BK2125 HS 750 2X1.25X0.85MM R/TP BK2125 HS 750 2X1.25X0.85MM R/TP FBMH3216 HM501NT 3.2X1.6X1.6MM R/TP RESONATOR,CRYSTAL HC49U 18.432MHZ 30PPM RESONATOR,CRYSTAL SX-1SMD 20250000HZ RESONATOR,CRYSTAL SX-1 13.500000MHZ RESONATOR,CRYSTAL SX-1 SC14.3MHZ
FILTER & CRYSTAL
F100 F101 F102 F103 F500 F501 F502 L100 L1000 L101 L102 L103 L104 L105 L106 L1305 L1307 L1308 L1309 L1400 L1401 L1402 L1404 L1405 L1406 L1409 L1410 L1412 L1413 L1414 L1415 L1416 L1417 L1418 L1419 L1420 L1421 L1422 L1423 L1424 L1425 L1426 L1427 6200J00012A 6200J00012A 6200J00012A 6200J00012A 6200VJS001A 6200VJS001B 6200VJS001B 6210VC0006A 6210VC0006A 6210VC0006A 6200JB8010L 6200JB8010L 6200JB8010L 6200JB8010L 6210VC0006A 6210VC0006A 6210VC0006A 6210VC0006A 6210VC0006A 6210VC0006A 6210VC0006A 6210VC0006A 6210VC0006A 6210VC0006A 6210VC0006A 6210VC0006A 6210VC0006A 6210VC0006A 6210VC0006A 6210VC0006A 6210VC0006A 6210VC0006A 6210VC0006A 6210VC0006A 6210VC0006A 6210VC0006A 6210VC0006A 6210VC0006A 6210VC0006A 6210VC0006A 6210VC0006A 6210VC0006A 6210VC0006A ACM2012-900H-2P TDK R/TP ACM2012-900H-2P TDK R/TP ACM2012-900H-2P TDK R/TP ACM2012-900H-2P TDK R/TP ZJY51R5-4P TDK DIP DC 50VOLT 2A ZJYS51R5-2PL(T) TDK R/TP 50VOLT 2A ZJYS51R5-2PL(T) TDK R/TP 50VOLT 2A FBMH3216 HM501NT 3.2X1.6X1.6MM R/TP FBMH3216 HM501NT 3.2X1.6X1.6MM R/TP FBMH3216 HM501NT 3.2X1.6X1.6MM R/TP MLB-201209-1000L-N2 R/TP 1000OHM 350MA MLB-201209-1000L-N2 R/TP 1000OHM 350MA MLB-201209-1000L-N2 R/TP 1000OHM 350MA MLB-201209-1000L-N2 R/TP 1000OHM 350MA FBMH3216 HM501NT 3.2X1.6X1.6MM R/TP FBMH3216 HM501NT 3.2X1.6X1.6MM R/TP FBMH3216 HM501NT 3.2X1.6X1.6MM R/TP FBMH3216 HM501NT 3.2X1.6X1.6MM R/TP FBMH3216 HM501NT 3.2X1.6X1.6MM R/TP FBMH3216 HM501NT 3.2X1.6X1.6MM R/TP FBMH3216 HM501NT 3.2X1.6X1.6MM R/TP FBMH3216 HM501NT 3.2X1.6X1.6MM R/TP FBMH3216 HM501NT 3.2X1.6X1.6MM R/TP FBMH3216 HM501NT 3.2X1.6X1.6MM R/TP FBMH3216 HM501NT 3.2X1.6X1.6MM R/TP FBMH3216 HM501NT 3.2X1.6X1.6MM R/TP FBMH3216 HM501NT 3.2X1.6X1.6MM R/TP FBMH3216 HM501NT 3.2X1.6X1.6MM R/TP FBMH3216 HM501NT 3.2X1.6X1.6MM R/TP FBMH3216 HM501NT 3.2X1.6X1.6MM R/TP FBMH3216 HM501NT 3.2X1.6X1.6MM R/TP FBMH3216 HM501NT 3.2X1.6X1.6MM R/TP FBMH3216 HM501NT 3.2X1.6X1.6MM R/TP FBMH3216 HM501NT 3.2X1.6X1.6MM R/TP FBMH3216 HM501NT 3.2X1.6X1.6MM R/TP FBMH3216 HM501NT 3.2X1.6X1.6MM R/TP FBMH3216 HM501NT 3.2X1.6X1.6MM R/TP FBMH3216 HM501NT 3.2X1.6X1.6MM R/TP FBMH3216 HM501NT 3.2X1.6X1.6MM R/TP FBMH3216 HM501NT 3.2X1.6X1.6MM R/TP FBMH3216 HM501NT 3.2X1.6X1.6MM R/TP FBMH3216 HM501NT 3.2X1.6X1.6MM R/TP FBMH3216 HM501NT 3.2X1.6X1.6MM R/TP
JACK
P100 P102 P103 P200 P201 P202 P203 P204 380-068E 6612BBBHN6A 380-068E 6612J00010A 6612VJH019C 380-363K 6612M00001A 6612M00001A UEJ-CV-018 UGCOM D3.5 E/P 440062-1 AMP DVI INTERACED UEJ-CV-018 UGCOM D3.5 E/P PPJ128A-1 A/V 2P MONO GN-BL-RD PPJ121-22 A/V 4P FOR EMI WITH SWITCH RED PJ6046G PARKELEC H=8.0 W/O UPJ-R1-023 UGCOM 21PIN W/SHLD UPJ-R1-023 UGCOM 21PIN W/SHLD
ACCESSORIES
A1 A2 A3 A4 3828VA0513F 6710V00138D 6410VEH003C 6850J00005A MANUAL,OWNERSRF04GA PM10 138D TX 026H REMOTE CONTROLLERRF04GA MZ-42PM10 40 POWER CORDM2511A-001 2800MM PLUG IVORY CABLE,DVILVDS UL20276 AWG30 500MM
MISCELLANEOUS
F801 0FS1002B53K FUSE,SLOW BLOW 10000MA 250 V 5.2X20
- 38 -
PRINTED CIRCUIT BOARD
MAIN (TOP) MAIN (BOTTOM )
A/V FIX B/D(TOP)
A/V FIX B/D(TOP)
A/V RCA PAL(ToOP)
A/V RCA PAL(BOTTOM)
CONTROL
P/NO : 3828VD0198N
Dec., 2004 Printed in Korea