Text preview for : lg_mc019a_chassis_cf21s11kex_sm.pdf part of LG CF-20/21S11KEX:CF-20/21T20K/20T22KX:CF-20K51KEX:CF-20/21F60K/KX CF-20/21S11KEX
MODEL : CF-20/21T20K/20T22KX
MODEL : CF-20K51KEX
MODEL : CF-20/21F60K/KX
Back to : lg_mc019a_chassis_cf21s11 | Home
website:http://biz.LGservice.com e-mail:http://www.LGEservice.com/techsup.html
COLOR TV SERVICE MANUAL
CHASSIS : MC-019A
MODEL : CF-20/21S11KEX MODEL : CF-20/21T20K/20T22KX MODEL : CF-20K51KEX MODEL : CF-20/21F60K/KX
CAUTION
BEFORE SERVICING THE CHASSIS, READ THE SAFETY PRECAUTIONS IN THIS MANUAL.
P/NO : 3828VD0104L
Sep.,2001 Printed in Korea
NATVRAL ALGORITHM
EYE
CONTENTS
Contents ................................................................................................................. 2 Safety Precautions ............................................................................................3 Servicing Precautions ..................................................................................... 4 Specifications ..................................................................................................... 6 Description of Controls .................................................................................. 7 Disassembly Instructions .............................................................................10 Adjustment ............................................................................................................11 Purity & Convergence Adjustment ..........................................................14 Block Diagram ......................................................................................................17 Exploded View .................................................................................................. 18 Exploded View Parts List ..............................................................................19 Replacement Parts List ............................................................................... 26 SVC. Sheet ................................................................................................................
- 2 -
SAFETY PRECAUTIONS
IMPORT ANT SAFETY NOTICE
Many electrical and mechanical parts in this chassis have special safety-related characteristics. These parts are identified by in the Schematic Diagram and Replacement Parts List. It is essential that these special safety parts should be replaced with the same components as recommended in this manual to prevent X-RADIATION, Shock, Fire, or other Hazards. Do not modify the original design without permission of manufacturer.
General Guidance
An lsolation Transformer should always be used during the servicing of a receiver whose chassis is not isolated from the AC power line. Use a transformer of adequate power rating as this protects the technician from accidents resulting in personal injury from electrical shocks. It will also protect the receiver and it's components from being damaged by accidental shorts of the circuitary that may be inadvertently introduced during the service operation. If any fuse (or Fusible Resistor) in this TV receiver is blown, replace it with the specified. When replacing a high wattage resistor (Oxide Metal Film Resistor, over 1W), keep the resistor 10mm away from PCB. Keep wires away from high voltage or high temperature parts. Due to high vacuum and large surface area of picture tube, extreme care should be used in handling the Picture Tube. Do not lift the Picture tube by it's Neck.
Before returning the receiver to the customer,
always perform an AC leakage current check on the exposed metallic parts of the cabinet, such as antennas, terminals, etc., to be sure the set is safe to operate without damage of electrical shock.
Leakage Current Cold Check(Antenna Cold Check)
With the instrument AC plug removed from AC source, connect an electrical jumper across the two AC plug prongs. Place the AC switch in the on positioin, connect one lead of ohm-meter to the AC plug prongs tied together and touch other ohm-meter lead in turn to each exposed metallic parts such as antenna terminals, phone jacks, etc. If the exposed metallic part has a return path to the chassis, the measured resistance should be between 1M and 5.2M. When the exposed metal has no return path to the chassis the reading must be infinite. An other abnormality exists that must be corrected before the receiver is returned to the customer.
Leakage Current Hot Check (See below Figure)
Plug the AC cord directly into the AC outlet. Do not use a line Isolation Transformer during this check. Connect 1.5K/10watt resistor in parallel with a 0.15uF capacitor between a known good earth ground (Water Pipe, Conduit, etc.) and the exposed metallic parts. Measure the AC voltage across the resistor using AC voltmeter with 1000 ohms/volt or more sensitivity. Reverse plug the AC cord into the AC outlet and repeat AC voltage measurements for each esposed metallic part. Any voltage measured must not exceed 0.75 volt RMS which is corresponds to 0.5mA. In case any measurement is out of the limits sepcified, there is possibility of shock hazard and the set must be checked and repaired before it is returned to the customer.
X-RAY Radiation
Warning:
The source of X-RAY RADIATION in this TV receiver is the High Voltage Section and the Picture Tube. For continued X-RAY RADIATION protection, the replacement tube must be the same type tube as specified in the Replacement Parts List.
To determine the presence of high voltage, use an accurate high impedance HV meter. Adjust brightness, color, contrast controls to minimum. Measure the high voltage. The meter reading should indicate 23.5 ¡ 1.5KV: 14-19 inch, 26 ¡ 1.5KV: 19-21 inch, 29.0 ¡ 1.5KV: 25-29 inch, 30.0 ¡ 1.5KV: 32 inch If the meter indication is out of tolerance, immediate service and correction is required to prevent the possibility of premature component failure.
Leakage Current Hot Check circuit
AC Volt-meter
To Instrument's exposed METALLIC PARTS
Good Earth Ground such as WATER PIPE, CONDUIT etc.
0.15uF
1.5 Kohm/10W
- 3 -
SERVICING PRECAUTIONS
CAUTION: Before servicing receivers covered by this service manual and its supplements and addenda, read and follow the SAFETY PRECAUTIONS on page 3 of this publication. NOTE: If unforeseen circumstances create conflict between the following servicing precautions and any of the safety precautions on page 3 of this publication, always follow the safety precautions. Remember: Safety First. General Servicing Precautions 1. Always unplug the receiver AC power cord from the AC power source before; a. Removing or reinstalling any component, circuit board module or any other receiver assembly. b. Disconnecting or reconnecting any receiver electrical plug or other electrical connection. c. Connecting a test substitute in parallel with an electrolytic capacitor in the receiver. CAUTION: A wrong part substitution or incorrect polarity installation of electrolytic capacitors may result in an explosion hazard. d. Discharging the picture tube anode. 2. Test high voltage only by measuring it with an appropriate high voltage meter or other voltage measuring device (DVM, FETVOM, etc) equipped with a suitable high voltage probe. Do not test high voltage by "drawing an arc". 3. Discharge the picture tube anode only by (a) first connecting one end of an insulated clip lead to the degaussing or kine aquadag grounding system shield at the point where the picture tube socket ground lead is connected, and then (b) touch the other end of the insulated clip lead to the picture tube anode button, using an insulating handle to avoid personal contact with high voltage. 4. Do not spray chemicals on or near this receiver or any of its assemblies. 5. Unless specified otherwise in this service manual, clean electrical contacts only by applying the following mixture to the contacts with a pipe cleaner, cotton-tipped stick or comparable nonabrasive applicator; 10% (by volume) Acetone and 90% (by volume) isopropyl alcohol (90%-99% strength) CAUTION: This is a flammable mixture. Unless specified otherwise in this service manual, lubrication of contacts in not required. 6. Do not defeat any plug/socket B+ voltage interlocks with which receivers covered by this service manual might be equipped. 7. Do not apply AC power to this instrument and/or any of its electrical assemblies unless all solid-state device heat sinks are correctly installed. 8. Always connect the test receiver ground lead to the receiver chassis ground before connecting the test receiver positive lead. Always remove the test receiver ground lead last. 9. Use with this receiver only the test fixtures specified in this service manual. CAUTION: Do not connect the test fixture ground strap to any heatsink in this receiver. Electrostatically Sensitive (ES) Devices Some semiconductor (solid state) devices can be damaged easily by static electricity. Such components commonly are called Electrostatically Sensitive (ES) Devices. Examples of typical ES devices are integrated circuits and some fieldeffect transistors and semicounductor "chip" components. The following techniques should be used to help reduce the incidence of component damage caused by static by static electricity. 1. Immediately before handling any semiconductor component or semiconductor-equipped assembly, drain off any electostatic charge on your body by touching a known earth ground. Alternatively, obtain and wear a commercially available discharging wrist strap device, which should be removed to prevent potential shock reasons prior to applying power to the unit under test. 2. After removing an electrical assembly equipped with ES devices, place the assembly on a conductive surface such as aluminum foil, to prevent electrostatic charge buildup or exposure of the assembly. 3. Use only a grounded-tip soldering iron to solder or unsolder ES devices. 4. Use only an anti-static type solder removal device. Some solder removal devices not classified as "anti-static" can generate electrical charges sufficent to demage ES devices. 5. Do not use freon-propelled chemicals. These can generate electrical charges sufficient to damage ES devices. 6. Do not remove a repalcement ES device from its protective package until immediately before you are ready to install it. (Most replacement ES devices are packaged with leads electrically shorted together by conductive foam, aluminum foil or comparable conductive material). 7. Immediately before removing the protective material from the ieads of a replacement ES device, touch the protective material to the chassis or circuit assembly into which the device will be installed. CAUTION:Be sure no power is applied to the chassis or circuit, and observe all other safety precautions. 8. Minimize bodily motions when handling unpackaged replacement ES devices. (Otherwise harmless motion such as the bruching together of your clothes fabric or the lifting of your foot from a carpeted floor can generate static electricity sufficient to damage an ES device.) General Soldering Guidelines 1. Use a grounded-tip, low-wattage soldering iron and appropriate tip size and shape that will maintan tip temperature within the range or 500¡£ to 600¡£ F F. 2. Use an appropriate gauge of RMA resin-core solder composed of 60 parts tin/40 parts lead. 3. Keep the soldering iron tip clean and well tinned. 4. Thorohly clean the surfaces to be soldered. Use a mall wirebristle (0.5 inch, or 1.25cm) brush with a metal handle. Do not use freon-propelled spray-on cleaners. 5. Use the following unsoldering technique a. Allow the soldering iron tip to reach normal temperature. (500¡£ to 600¡£ F F) b. Heat the component lead until the solder melts. c. Quickly draw the melted solder with an anti-static, suction-type solder removal device or with solder braid. CAUTION: Work quickly to avoid overheating the circuiboard printed foil. 6. Use the following soldering technique. a. Allow the soldering iron tip to reach a normal temperature (500¡£ to 600¡£ F F) b. First, hold the soldering iron tip and solder the strand against the component lead until the solder melts.
- 4 -
c. Qulckly move the soldering iron tip to the junction of the component lead and the printed circuit foil, and hold it there only until the solder flows onto and around both the component lead and the foil. CAUTION: Work quickly to avoid overheating the circuit board printed foil. d. Closely inspect the solder area and remove any excess or splashed solder with a small wire-bristle brush. IC Remove/Replacement Some chassis circuit boards have slotted holes (oblong) through which the IC leads are inserted and then bent flat against the circuit foil. When holes are the slotted type, the following technique should be used to remove and replace the IC. When working with boards using the familiar round hole, use the standard technique as outlined in parapraphs 5 and 6 above. Remov 1. Desolder and straighten each IC lead in one operation by gently prying up on the lead with the soldering iron tip as the solder melts. 2. Draw away the melted solder with an anti-static suctiontype solder removal device (or with solder braid) before removing the IC. Replacemen 1. Carefully insert the replacement IC in the circuit boare. 2. Carefully bend each IC lead against the circuit foil pad and solder it. 3. Clean the soldered areas with a small wire-bristle brush. (It is not necessary to reapply acrylic coating to the areas). "Small-Signal" Discrete Transistor Removal/Replacement 1. Remove the defective transistor by clipping its leads as close as possible to the component body. 2. Bend into a "U" shape the end of each of three leads remaining on the circuit board. 3. Bend into a "U" shape the replacement transistor leads. 4. Connect the replacement transistor leads to the corresponding leads extending from the circuit board and crimp the "U" with long nose pliers to insure metal to metal contact then solder each connection. Power Output, Transistor Device Removal/Replacement 1. Heat and remove all solder from around the transistor leads. 2. Remove the heatsink mounting screw (if so equipped). 3. Carefully remove the transistor from the heat sink of the circuit board. 4. Insert new transistor in the circuit board. 5. Solder each transistor lead, and clip off excess lead. 6. Replace heatsink. Diode Removal/Replacement 1. Remove defective diode by clipping its leads as close as possible to diode body. 2. Bend the two remaining leads perpendicula y to the circuit board. 3. Observing diode polarity, wrap each lead of the new diode around the corresponding lead on the circuit board. 4. Securely crimp each connection and solder it. 5. Inspect (on the circuit board copper side) the solder joints of the two "original" leads. If they are not shiny, reheat them and if necessary, apply additional solder.
Fuse and Conventional Resistor Removal/Replacement 1. Clip each fuse or resistor lead at top of the circuit board hollow stake. 2. Securely crimp the leads of replacement component around notch at stake top. 3. Solder the connections. CAUTION: Maintain original spacing between the replaced component and adjacent components and the circuit board to prevent excessive component temperatures. Circuit Board Foil Repair Excessive heat applied to the copper foil of any printed circuit board will weaken the adhesive that bonds the foil to the circuit board causing the foil to separate from or "lift-off" the board. The following guidelines and procedures should be followed whenever this condition is encountered. At IC Connections To repair a defective copper pattern at IC connections use the following procedure to install a jumper wire on the copper pattern side of the circuit board. (Use this technique only on IC connections). 1. Carefully remove the damaged copper pattern with a sharp knife. (Remove only as much copper as absolutely necessary). 2. carefully scratch away the solder resist and acrylic coating (if used) from the end of the remaining copper pattern. 3. Bend a small "U" in one end of a small gauge jumper wire and carefully crimp it around the IC pin. Solder the IC connection. 4. Route the jumper wire along the path of the out-away copper pattern and let it overlap the previously scraped end of the good copper pattern. Solder the overlapped area and clip off any excess jumper wire. At Other Connections Use the following technique to repair the defective copper pattern at connections other than IC Pins. This technique involoves the installation of a jumper wire on the component side of the circuit board. 1. Remove the defective copper pattern with a sharp knife. Remove at least 1/4 inch of copper, to ensure that a hazardous condition will not exist if the jumper wire opens. 2. Trace along the copper pattern from both sides of the pattern break and locate the nearest component that is directly connected to the affected copper pattern. 3. Connect insulated 20-gauge jumper wire from the lead of the nearest component on one side of the pattern break to the lead of the nearest component on the other side. Carefully crimp and solder the connections. CAUTION: Be sure the insulated jumper wire is dressed so the it does not touch components or sharp edges.
- 5 -
SPECIFICA TIONS
Note : Specification and others are subject to change without notice for improvement. ¡ Video input system: PAL-B/G, D/K, I/I SECAM-B/G, D/K,L/L' NTSC M NTSC 4.43 ¡ Intermediate Frequency (Unit : MHz) VISION IF : 38.9MHz COLOR IF : 34.47MHz(4.43) 35.32MHz(3.58) : NTSC-M VIF-4.25000MHz ): SECAM ( VIF-4.40625MHz SOUND IF : 33.4MHz (B/G) 32.9MHz (I/I) 32.4MHz (D/K) 34.4MHz (M)
¡ Power requirement : 110~240V, 50/60Hz ¡ Power consumption : 95 ¡ STAND-BY : 3W
¡ Tuning range Band VHF-Low VHF-High Hyper UHF Ch21-69 Ch14-69 For TV B/G Ch2-4 Ch5-12 D/K Ch1-5 Ch6-12 Ch4-13 Ch2-13 I/I NTSC S1'-S3', S1 S2-S10, S11-S20 S21-S41 For CATV
¡ Tuning system : FVS 100 Programme memory 200 Programme memory(W/O TXT) ¡ Antenna input impedance : VHF/UHF 75 ohm, unbalanced ¡ OSD (On Screen Display) : EASY-MENU ¡ Voice coil impedance : 8 ohm ¡ Sound output : 7W¡¿2(MAX) Dual/Stereo : A2/NICAM(Option) ¡ External connection : Head Phone Jack A/V in : 2 PERI Connector(Full Scart) : 1 DVD in
¡ Feature : Auto programme/Manual programme CSM (Color Status Memory) Auto Sleep Turbo Picture & Sound Programme Editing PSM (Picture Status Memory) Teletext (TOP/FLOF/LIST) ACMS Auto Volume Level Game SSM(Sound Status Memory) Favorite Program
¡ External In/Output Audio-In:0.5Vrms¡ 3dB,over 10Kohm Audio-Out:0.5Vrms¡ 3dBb,below 1Kohm Video-In/Out:1Vp-p¡ 3dB,75ohm DVD In Y: 1Vp-p¡ 3dB Pb,Pr : 0.7Vp-p¡ 3dB
- 6 -
DECRIPTIONS OF CONTROLS
All the functions can be controlled with the remote control handset. Some functions can also be adjusted with the buttons on the front panel of the set.
Remote control handset
Before you use the remote control handset, please install the batteries. See the next page.
POWER MUTE
1
1 2 5 8 0
TV
10
3 6 9
TV/AV
1. POWER switches the set on from standby or off to standby. 2. NUMBER BUTTONS switches the set on from standby or directly select a number. 3. MENU (or INDEX) selects a menu. selects an index page in the teletext mode (only TELETEXT models). 4. EYE/ (option) switches the eye function on or off.
2
4 7
MENU/INDEX
3 4
EYE/
11 12
I/II/
VOL
PR ( ) VOL
*
5 6
OK
PR ( )
5.
Q.VIEW
LIST
13
TEXT/MIX SIZE TIME SSM/ HOLD REVEAL SLEEP
M
7
UPDATE PSM
D( D ) / E( E ) (Programme Up/Down) D E selects a programme or a menu item. switches the set on from standby. scans programmes automatically. F / G (Volume Up/Down) adjusts the volume. adjusts menu settings. OK accepts your selection or displays the current mode.
8
/
PICTURE SOUND
14 6. Q.VIEW 15 returns to the previously viewed programme. selects a favorite programme. 16 7. TELETEXT BUTTONS (option) These buttons are used for teletext. For further details, see the ÔTeletextÕ section. 8. PSM (Picture Status Memory) recalls your preferred picture setting. 9. TURBO PICTURE / SOUND BUTTON (option) selects Turbo picture and sound.
TURBO/
9
(With TELETEXT)
- 7 -
10. MUTE switches the sound on or off. 11. TV/AV selects TV or AV mode. clears the menu from the screen. switches the set on from standby. 12. I/II/ (option) selects the language during dual language broadcast. (option) selects the sound output.
*
POWER
MUTE
13. LIST displays the programme table. 14. SLEEP sets the sleep timer. 15. SSM/ (option) (Sound Status Memory) recalls your preferred sound setting.
1
1 2 5 8 0 3 6 9
TV/AV
10
2
4 7
MENU
*
3 4
EYE/
VOL
11 12
I/II/
VOL
º 16. SURROUND (º/ ) (option) selects surround sound.
*
PR ( )
COLOURED BUTTONS : These buttons are used for teletext (only 5 TELETEXT models) or programme edit.
OK
PR ( )
Q.VIEW
LIST
Battery installation
The remote control handset is powered by two AAA type batteries. To load the batteries, turn the remote control handset over and open the battery compartment. Install two batteries as indicated by the polarity symbols ( + and - ) marked inside the compartment.
6
13
PSM
SSM/
SLEEP
8
/
PICTURE SOUND
14 15 16
TURBO/
9
Note : To avoid damage from possible battery leakage, remove the batteries if you do not plan to use the remote control handset for an extended period of time.
(Without TELETEXT)
- 8 -
Front panel
Shown is a simplified representation of front or side panel. Here shown may be somewhat different from your set.
VIDEO VIDEO
6
AUDIO
(L) I AUDIO I (R)
ON/OFF r
y
MENU
OK F VOL G E PR D
VIDEO
AV
AUDIO
§
1
2 3
y
4
5
VIDEO
6
AV
7
§
9
! !
VIDEO
7 7 6
ON/OFF r
MENU OK F VOL G E PR D
L -AUDIO- R
! !
VIDEO (L) I AUDIO I (R)
ON/OFF r MENU OK F VOL G E PR D VIDEO (L)-AUDIO-(R) § P-TURBO-S
1
ON/OFF
23
r
4
MENU
5
OK F VOL G E PR D
6
VIDEO AUDIO §
7
8
9
AUDIO
TURBO SOUND PICTURE
1 (Side panel)
ON/OFF
23
r
4
MENU
5
F VOL PR D PR E VOL G
6
OK
7
8
9
1
2 3 4
5
9
1. MAIN POWER (ON/OFF) switches the set on or off. 2. POWER/STANDBY INDICATOR illuminates brightly when the set is in standby mode. dims when the set is switched on. blinks when signal is input from the remote control. 3. REMOTE CONTROL SENSOR 4. MENU selects a menu. 5. OK accepts your selection or displays the current mode. F / G (Volume Up/Down) adjusts the volume. adjusts menu settings. D / E (Programme Up/Down) selects a programme or a menu item. switches the set on from standby. 6. AUDIO/VIDEO IN SOCKETS (AV) (option) Connect the audio/video out sockets of external equipment to these sockets. Note : Do not connect with the Euro scart socket simultaneously to receive a good front/side audio/video. 7. HEADPHONE SOCKET (option) Connect the headphone plug to this socket. 8. TURBO SOUND/PICTURE (option) switches Turbo sound or Turbo picture on or off. 9. EYE (option) adjusts picture according to the surrounding conditions.
- 9 -
DISASSEMBLY INSTRUCTIONS
Important note
This set is disconnected from the power supply through the converter transformer. An isolating transformer is necessary for service operations on the primary side of the converter transformer.
Chassis Assy Removal
Grasp both side of Frame and pull it backward smoothly.
Back Cabinet Removal
Remove the screws residing on the back cabinet and carefully separate the back cabinet from the front cabinet. (Fig. 2-1).
CPT Removal
1. Pull out the CPT board from the CPT neck. 2. Place the front cabinet on soft material not to mar the front surface or damage control knobs. 3. Remove 5 screws securing the picture tube mounting brackets to the front cabinet. 4. Carefully separate CPT from the front cabinet.
PICTURE TUBE HANDLING CAUTION
Due to high vacuum and large surface area of picture tube, great care must be exercised when handling picture tube. Always lift picture tube by grasping it firmly around faceplate. NEVER LIFT TUBE BY ITS NECK! The picture tube must not be scratched or subjected to excessive pressure as fracture of glass may result in an implosion of considerable violence which can cause personal injury or property damage.
CPT board Remove Screws
Main PCB
Fig. 2-1
Fig. 2-2
- 10 -
ADJUSTMENT
¡
Safety Precautions
1. It is safe to adjust after using insulating transformer between the power supply line and chassis input to prevent the risk of electric shock and protect the instrument. 2. Never disconnect leads while the TV receiver is on. 3. Don't short any portion of circuits while power is on. 4. The adjustment must be done by the correct appliances. But this is changeable in view of productivity. 5. Unless otherwise noted, set the line voltage to 110~240Vac¡ 10%, 50/60Hz. 6. The adjustment of TV should be performed afther warming up for 20 minutes.
Option TBS EYE
Code 0 1 0 1 0
Function W/O TBS WITH TBS W/O EYE WITH EYE W/O 4 KEY WITH 4 KEY
Remark
4 KEY MONO
1 0 1
FORCED MONO
Table 2. OPTION 2 Function
Option BCF Code 0 1 0 GAME 200 PRO CHA + AU DUAL 1 0 1 0 1 0 1 0 ACMS T-SCH 1 0 1 0 1 0 CURVE 1 Function Auto Abnormal ON Not Used W/O GAME PACK WITH GAME PACK 100 PRO 200 PRO Except China,Austrailia China,Austrailia W/O DUAL WITH DUAL Austrailia Except Austrailia W/O TURBO SEARCH WITH TURBO SEARCH W/O TURBO P/S WITH TURBO P/S NORMAL VOLUME CURVE M-A,India VOLUME CURVE Remark
¡
Test Equipment required
1. Multimeter (volt meter) 2. Oscilloscope 3. 10:1 PROBE 4. Color Analyzer
¡ CDL Data Adjustment(LINE SVC-0)
1) Press the SVC button to get into the SVC-0 Mode. 2) Press the Channel UP/DOWN button to select CDL12. 3) Press the Volume UP/DOWN button until the CDL data is the same as the Table below. 21Ó FCD CDL Data Remark 12 FLAT 14,16Ó CPT 8 15Ó CPT 10 FLAT 20,21Ó CPT 12
4) Press the OK(¡Æ button to memorize the data. )
¡ OPTION Data Adjustment(OPTION-1,OPTION-2)
1) Press OK buttons on both TV set and Remote Controller at the same time to get into SVC mode. 2) Press the Yellow button several times to find OPTION-1 or OPTION-2. 3) Input the correspond OPTION data referring to Table below with the numeric buttons. 4) Press the OK(¡Æ button to memorize the data. ) T-P/S
Table 3. OPTION 3 Function
Option Code Function *** *** W/O HOTEL W/HOTEL BG/L BG/I/DK BG/I/DK/M BG/I/DK DUAL BG/I/DK/M DUAL 2nd IF BG 2nd IF I 2nd IF DK Remark
Table 1. OPTION 1 Function
Option C MUTE DVD 2 IN 1 Code 0 1 0 1 0 1 0 1 0 SCART 1 Function ACTIVE NOT ACTIVE W/O DVD DVD(REAR JACK) W/O 2 IN 1TUNER WITH 2 IN 1TUNER FLOF TXT TOP TXT PHONO JACK SCART JACK Remark
RESER VED HOTEL
0 1 0 1 0 1 2
TOP
SYSTEM
3 4 5 6 7
- 11 -
Option Code 0 OSD-L (EU) 1 2
Function ENG. ONLY EU-7EA EU ALL
Remark English English,Deutsch,Francais,Italiano,Espanol English,Nederlands,Svenska,Dansk,Suomi,Por tugues,Romaneste,Polski,Cesky,Pyccknn
¡ FOCUS Adjustment
Test Point Adjust : RK (Red Cathode of CPT Board) : Screen Volume of FBT
3 0 OSD-L (MASIA) 1 2 3 OSD-L (E-ASIA) OSD-L (CH+HI) 0 1 0 1 2 0 TXT-L (EU) 1 2 3 TXT-L (E-ASIA) TXT-L (ARAB) TXT-L (FARSI) 0
EU EAST ENG. ONLY ARABIC PARSI ARAB,FARSI,URDE ENG.ONLY ASIA-ALL ENG.ONLY E+CHINA E+HINDI W-EU E-EU CYRILLIC UKRAINIAN WEST-EU
English,Romaneste,Polski,Cesky,Pyccknn,Magyar English English,Arab,,Urdu,French English,Parsi,Urdu,French English,French,Arab,Urdu,Parsi English English,Malay,Vietnam,Indonesian,Thai English English,Chinese English,Hindi
1) Tune the TV set to receive a PAL 05CH. 2) Adjust the Focus Volume of FBT for best focus.
¡ Screen Voltage Adjustment
Test Point Adjust : Observing Display : Focus Volume of FBT
1) Connect the probe of oscilloscope to the RK (Red Cathode) of CPT Board. 2) Set the oscilloscope to 50V/div and 20Us/div and after putting GND line upon the lowest grid line of the scope by pressing GND button,enter into DC mode. 3) Tune the TV set to receive a PAL-B/G 05CH. 4) Adjust Screen Volume of FBT so that the waveform is the same as below figure (DC 140¡ 3V).
Horizontal FlyBack Time
Black level 140Vp-p
0 1 0 1
WEST-EU ARABIC WEST-EU FARSI 14Ó DC 130V¡ 3 V OTHERS DC 140V¡ 3 V
White level GND for dc
¡ AGC Adjustment (SERVICE 1)
Test Point Adjust : AGC TP (C101) : Remote Controller
¡ White Balance Adjustment.(LINE SVC-0)
NOTE : This adjustment should be performed after screen voltage adjustment. 1) Tune the TV set to receive an 100% white pattern. 2) Press OK(¡Æ) buttons on TV set and remote controller at the same time to get into SVC mode. 3) Press Yellow button on remote controller. (Standard mode) 4) Press Channel UP/DOWN button for desirous function adjustment. 5) Adjust VOL+ or VOL-button in each status of "RG--"/"BG--" for X=272¡ 8, Y=288¡ 8 with color analyzer.(Europe Model : X=288¡ 8, Y=295¡ X=272¡ 8, 11,000K) Status Tuner P/N Marker AGC Voltage Tuner P/N Marker AGC Voltage 6700VPF009G LG Innotek(W/S TUNER) 2.7¡ 0.05V 6700VPF009S LG Innotek(TBS TUNER) 2.5¡ 0.05V BLO-R BLO-G 31 31 6700VPF016A DAEWOO(W/S TUNER) 2.7¡ 0.05V GG BG 31 31 RG Initial Data 31 Remark
1) Connect RF signal (70dB¡ 0.2dB) and turn on the TV. ¡ Standard adjustment Channel - EU 05 Ch. (frf = 175.25MHz) 2) Press the OK buttons on TV set and Remote Controller at the same time to get into SVC-0 mode. 3) Press the Channel UP/DOWN button on the Remote Controller several times to find AGC??. 4) Press the Volume UP/DOWN button until the AGC Voltage is the same as the Table below. 5) Press the OK(¡Æ button to memorize the data. )
7) Press the OK(¡Æ) button to memorize the data.
- 12 -
¡ Deflection Data Adjustment (Line SVC-1)
NOTE: To enter SVC mode, press "OK" buttons on both TV set and the Remote control at the same time.
1. Preparation for Deflection Adjustment
1) At SVC mode, press the Yellow colored button. And then, deflection data adjustment OSD (SVC1 mode) will be displayed. 2) Tune the TV set to receive a PAL 05 CH.
2. Deflection Initial Setup Data
Status VL VA VS HS SC Default 31 31 31 31 25 21" FLAT S/S 31 31 31 31 25 21" FLAT LG 31 31 31 31 25
3. Deflection Adjustment Procedure
VL (Vertical Linearity) Adjust so that the boundary line between upper and lower half is in accord with geometric horizontal center of the CPT. VA (Vertical Amplitude) Adjust so that the circle of a digital circle pattern may be located within the effective screen of the CPT. SC (Vertical "S" Correction) Adjust so that all distance between each horizontal lines are to be the same. VS (Vertical Shift) Adjust so that the horizontal center line of a digital circle pattern is in accord with geometric horizontal center of the CPT.
HS (Horizontal Shift) Adjust so that the vertical center line of a digital circle pattern is in accord with geometric vertical center of the CPT. Press the OK(¡Æ button to memorize the data. )
- 13 -
PURITY & CONVERGENCE ADJUSTMENT
Caution:
Convergence and Purity have been factory aligned. Do not attempt to tamper with these alignments. However, the effects of adjacent receiver components, or replacement of picture tube or deflection yoke may require the need to readjust purity any convergence. 5. Reconnect the internal degaussing coil. 6. Position the beam bender locking rings at the 9 o'clock position and the other three pairs of tabs (2,4 and 6 pole magnets) at the 12 o'clock position.
DEFLECTION YOKE PURITY &CONVERGENCE MAGNET ASSEMBLY
6-POLE MAGNETS MAGNES
6-POLE
PURITY MAGNET(2-POLE)
6-POLE
,, ,,,, ,,,, , ,,,, ,,,, ,,,,
, ,,,,
RUBBER WEDGES
¡ Purity Adjustment
This procedure DOES NOT apply to bonded yoke and picture tube assemblies. The instrument should be at room temperature (60 degrees F or above) for six (6) hours and be operating at low beam current (dark background) for approximately 20 to 30 minutes before performing purity adjustments.
CAUTION: Do not remove any trim magnets that may be attached to the bell of the picture tube.
1. Remove the AC power and disconnect the internal degaussing coil. 2. Remove the yoke from the neck of the picture tube. 3. If the yoke has the tape version beam bender, remove it and replace it with a adjustable type beam bender (follow the instructions provided with the new beam bender) 4. Replace the yoke on the picture tube neck, temporarily remove the three (3) rubber wedges from the bell of the picture tube and then slide the yoke completely forward.
,, , ,,,, , ,,,, , ,,,, , ,,,, , , ,,,, , ,,,, , ,,,, , ,,,,
, ,,,,
4-POLE X-AXIS YOKE MAGNET POSITIONING (L/R PURITY)
PURITY MAGNET 4-POLE
GLASS CLOTH TAPE
CONVERGENCEMAGNET ASSEMBLY MAGNET ASSEMBLY CONVERGENCE
7. Perform the following steps, in the order given, to prepare the receiver for the purity adjustment procedure. a. Face the receiver in the "magnetic north" direction. b. Externally degauss the receiver screen with the television power turned off. c. Turn the television on for approximately 10 seconds to perform internal degaussing and then turn the TV off. d. Unplug the internal degaussing coil. This allows the thermistor to cool down while you are performing the purity adjustment. DO NOT MOVE THE RECEIVER FROM ITS "MAGNETIC NORTH" POSITION. e. Turn the receiver on and obtain a red raster by increasing the red bias control (CW) and decreasing the bias controls for the remaining two colors (CCW). f. Attach two round magnets on the picture tube screen at 3 o'clock and 9 o'clock positions, approximately one (1) inch from the edge of the mask (use double-sided tape).
- 14 -
1.ADJUST YOKE Z-AXIS FIRST TO GET EQUAL BLUE COLOR CIRCLES
2 .ADJUST BEAM BENDER 2 POLE MAGNET TO GET FOUR EQUAL COLOR CIRCLES
MAGNETS
RED
RED
8. Referring to above, perform the following two steps: a. Adjust the yoke Z-axis to obtain equal blue circles. b. Adjust the appropriate beam bender tabs to obtain correct purity (four equal circles). 9. After correct purity is set, tighten the yoke clamp screw and remove the two screen magnets. 10. Remove the AC power and rotate the receiver 180 degrees (facing "magnetic south"). 11. Reconnect the internal degaussing coil. 12. Turn the receiver on for 10 seconds (make sure the receiver came on) to perform internal degaussing, and then turn the receiver off. 13. Unplug the internal degaussing coil. 14. Turn on the receiver and check the purity by holding one (1) round magnet at the 3 o'clock and a second round magnet at 9 o'clock position. If purity is not satisfactory, repeat steps 8 through 14. 15. Turn off the receiver and reconnect the internal degaussing coil.
6. Reconnect the internal degaussing coil and apply AC power. 7. Turn the receiver on for 10 seconds to perform internal degaussing and then turn the receiver off again. 8. Unplug the internal degaussing-coil. 9. Turn on the receiver, connect a signal generator to the VHF antenna terminal and apply a crosshatch signal.
Caution: During the convergence adjustment procedure, be very careful not to disturb the purity adjustment tabs are accidentally move, purity should be confirmed before proceeding with the convergence adjustments. Note: Make sure the focus is set correctly on this instrument before proceeding with the following adjustment.
10. Converge the red and blue vertical lines to the green vertical line at the center of the screen by performing the following steps (below TABLE). a. Carefully rotate both tabs of the 4-pole ring magnet simultaneously in opposite directions from the 12 o'clock position to converge the red and blue vertical lines. b. Carefully rotate both tabs of the 6-pole ring magnet simultaneously in opposite directions form the 12 o'clock position to converge the red and blue (now purple) vertical lines with the green vertical line. 11. Converge the red and blue horizontal with the green line at the center of the screen by performing the following steps. (below TABLE) a. Carefully rotate both tabs of the 4-pole ring magnet simultaneously in the same direction (keep the spacing between the two tabs the same) to converge the red and blue horizontal lines. b. Carefully rotate both tabs of the 6-pole ring magnet simultaneously in same direction (keep the spacing between the two tabs the same) to converge the red and blue (now purple) horizontal lines with the green horizontal line. c. Secure the tabs previsouly adjusted by locking them in place with the locking tabs on the beam bender.
¡ Convergence Adjustment
Caution: This procedure DOES NOT apply to bonded yoke and picture tube assemblies. Do not use screen magnets during this adjustment procedure. Use of screen magnets will cause an incorrect display.
1. Remove AC power and disconnect the internal degaussing coil. 2. Apply AC Power and set the brightness to the Picture Reset condition. Set the Color control to minimum. 3. Make a horizontal line. 4. Adjust the Red, Green and Blue Bias controls to get a dim white line. 5. Restore the screen by removing the horizontal line.
- 15 -
RING PAIRS
ROTATION DIRECTION OF BOTH TABS
MOVEMENT OF RED AND BLUE BEAMS
B OPPOSITE 4 POLE SAME B R OR
B R
R
OR
B
R
B OPPOSITE R 6 POLE SAME B R OR OR
B R
B
R
UP/DOWN ROCKING OF THE YOKE UP/DOWN ROCKING OF THE YOKE CAUSES OPPOSITE ROTATION OF RED CAUSES RASTERS AND BLUE OPPOSITE ROTATION OF RED
AND BLUE RASTERS
LEFT/RIGHT ROCKING OF THE YOKE LEET/RIGHT ROCKING OF THE OF THE CAUSES OPPOSITE SIZE CHANGE YOKE CAUSES OPPOSITE SIZE RED AND BLUE RASTERS CHANGE OF
THE RED AND BLUE RASTERS
GREEN
GREEN
ADJUSTMENT VIEWING AREA
BLUE
RED
ADJUSTMENT VIEWING AREA
RED RED
GREEN
RED BLUE
BLUE RED
GREEN
RED
BLUE TV SCREEN
GREEN
12. While watching the 6 o'clock positions on the screen, rock the front of the yoke in a vertical (up/down) direction to converge the red and blue vertical lines. (Fig upper left) 13. Temporarily place a rubber wedge at the 12 o'clock position to hold the vertical position or the yoke. 14. Check the 3 o'clock and 9 o'clock areas to confirm that the red and blue horizontal lines are converged. If the lines are not converged, slightly offset the vertical tilt of the yoke (move the rubber wedge if necessary) to equally balance the convergence error of the horizontal lines at 3 o'clock and 9 o'clock and the vertical lines at 6 o'clock and 12 o'clock. 15. Place a 1.5 inch piece of glass tape over the rubber foot at the rear of the 12 o'clock wedge. 16. While watching the 6 o'clock and 12 o'clock areas of the screen, rock the front of the yoke in the horizontal (left to right) motion to converge the red and blue horizontal lines. (Fig. upper right)
17. Temporarily place a rubber wedge at the 5 o'clock and 7 o'clock positions to hold the horizontal position of the yoke. 18. Check the 3 o'clock and 9 o'clock areas to confirm that the red and blue vertical lines are converged. If the lines are not converged, slightly offset the horizontal tilt of the yoke (move the temporary rubber wedges if necessary) to equally balance the convergence error of the horizontal lines at 6 o'clock and 12 o'clock and the vertical lines at 3 o'clock and 9 o'clock. 19. Using a round magnet confirm purity at the center, right and left sides and corners. See Purity Adjustment Procedure. 20. Reconfirm convergence and apply a 1.5 inch piece of glass tape over the rubber foot at the rear of the 5 o'clock and the 7 o'clock wedges.
- 16 -
Option Part IIC Bus Line SPK. SPK.
¡Ü
Front-AV(2)
H/P AV-IN
R.G.B AMP. & CPT DRIVE (TDA6107Q)
¡Ü
7
IC651 4 LA7016(Mono Opt) TV Audio(From UOC #28)
/ Game Audio (From HIC01)
2
MNT Audio Out(Mono) TV Audio Out (CL Mono)
ST-BY TRANS (3W Opt)
AC INPUT (110~240V)
PJ202
MONO SOUND AMP TDA2006 STEREO, STEREO, Sound Max SOUND AMP. SOUND AMP. TDA7266/97 TDA7266/97
AUDIO SIF
TO IC631 #1,#5
¡Ü
IC631 A1/A2(R/L)-IN 1 AV STEREO ¡Ü 32 30 TDA9859 28 41 42 40 IC661 ¡Ü RF STEREO 39 DVD(R/L)-IN / Game Audio 24
25
15 18
9 AUDIO B+
(14/17V) IC842 5V REG
¡Ü
SMPS TRANS
MONO ( ~B01L ) STEREO ( ~B01K ~ A13P)
10
SPK(L)-OUT
¡Ü
MSP3410D
44 47
31 30 MNT/TV-A(R/L)-OUT
IC844 8V REG H-Vcc IC131 5V REG
9.5V
BLOCK DIAGRAM
SPK(R/L)-OUT
¡Ü
AM-IN (L/L Only) FM-SIF-IN
¡Ü
Sound Trap Part
¡Ü ¡Ü
12 14V
B+ (110/115V)
Audio(Mono) (TV OUT)
IC02 3.3V Reg.
¡Ü
8V From IC844
EXT.RGB
Video-OUT(TV/MNT OUT) A(R/L)-OUT (MNT/TV-OUT)
EXT Video
3.3V
¡Ü
EXT Video(To UOC #42)
- 17 -
51~53 50 42 35 EXT RGB IK EXT Audio-in OUT Video-in 44 Audio Out IC03 EEPROM 24C08/16 SCL SDA 14 39 39
Int. CVBS
38 IFout SIF 32
SFE 5.74M
¡Ü
VIDEO SW1 SW2
5V From IC131
UOC TDA9361(TXT) TDA9381(Non-TXT)
28 14 39 33
Thai Opt.
V_DY Va Vb
Va 22 Vb 21 H-out
VERTICAL AMP LA7840
6 5 -14V
5V
5V From IC842
14V
8V From IC844
SIF(CE Mono) From Tuner
2 185V 10 AFC 8 ABL 9 HEATER 3 B+ Collector 1 4 7
FBT
5V 5.1V SDA SCL
A1(R/L)-IN
V-OUT
From UOC Video(Game) 1 Audio(Game) DVD Y / Game Video
Y/Pb/Pr
3, 4, 5
HIC01 Game Pack(Game Opt)
2
Rear_AV(1)
( SCART / PHONE)
DVD
(FLAT OPT.)
IC591 ) LA7016(DVD / GameOpt)
2
HDT
TUNER
PJ201
EXPLODED VIEW : 20/21S11KEX
943
913 150 153
400
170 112
174
120
104 300
520
310
700 320
354
330
350
- 18 -
EXPLODED VIEW PARTS LIST
PART NO LOCA. NO 20" 21"
The components identified by mark critical for safety. Replace only with part number specified.
are
DESCRIPTIONS
104 112 120 150 170 174 300 310 320 330 350 354 400 520 700 913 943
343-B52A 112-C20S 120-D38F 150-D02Y 170-A01D 174-009E 3091V00262G 5020V00187A 320-062H 5020V00186A 3750V00009G 4980V00035A 3809V00082M 6871VMM809T 0IGL120104A 332-057B 1PTF0403116
343-B52A 112-C21G 120-D38F 150-D02X 170-A01D 174-009E 3091V00345C 5020V00166A 320-070G 5020V00165A 3750V00009G 4980V00035A 3809V00082M 6871VMM809T 0IGL120104A 332-057B 1PTF0403116
SUPPORTER,PCB CPT SET SPEAKER COIL,DEGAUSSING LEAD SET,CPT EARTH POWER CORD(W/HOLD,HOUSING,L=200,4.0 CABINET ASSY STEREO #16 . . BUTTON,CONTROL SPRING,COIL BUTTON,POWER RACK BASE ASSY 20Ó/21Ó C/SKD,SAME SUPPORTER,BASE(SWIVEL+C/A) BACK COVER ASSY(SCART,D-GRAY) PWB ASSY,MAIN IC,CDS SENSOR MODULE(P1201-04) SCREW ASSY,HEXAGON HEAD SCREW,TAP TITE(P) D4.0 L16.0
- 19 -
EXPLODED VIEW : 20/21T20KX
943
913 170 150 153
400
112
174
OPTION
520
310
300
120
320 330
- 20 -
EXPLODED VIEW PARTS LIST
PART NO LOCA. NO 20" 21"
The components identified by mark critical for safety. Replace only with part number specified.
are
DESCRIPTIONS
112 120
112-C20S 120-C93G 6400VA0019C
112-C21G 120-C93G 6400VA0019C 150-D02X 170-A01D 174-009E 3091V00202S 5020V00070H 320-070G 5020V00071B 3809V00149C 6871VMM714L 332-057J 1PTF0403116
CPT SET SPEAKER SPEAKER COIL,DEGAUSSING LEAD SET,CPT EARTH POWER CORD(W/HOLD,HOUSING,L=200,4.0 CABINET ASSEMBLY STEREO CABINET ASSEMBLY MONO BUTTON,CONTROL 6KEY SPRING,COIL BUTTON,POWER BACK COVER ASSEMBLY(SCART) PWB ASSY,MAIN T22X PWB ASSY,MAIN T20KX SCREW ASSY,HEXAGON HEAD SCREW,TAP TITE(P) D4.0 L16
150 170 174 300
150-D02Y 170-A01D 174-009E 3091V00201M 3091V00201N
310 320 330 400 520
5020V00070H 320-070G 5020V00071B 3809V00149C 6871VMM714M 6871VMM809L
913 943
332-057B 1PTF0403116
- 21 -
EXPLODED VIEW : 20K51KEX
943
913 150 153
400
170 112
174
120 104
520
310
330
320
300
- 22 -
EXPLODED VIEW PARTS LIST
LOCA. NO PART NO DESCRIPTIONS
The components identified by mark critical for safety. Replace only with part number specified.
is
104 112 120 150 170 174 300 310 320 330 400 520 700 913 943
343-B52A 112-C20S 120-C77G 150-D02Y 170-A01D 174-009E 3091V00378D 5020V00158A 320-062E 5020V00161A 3809V00069V 6871VMM714Q 0IGL120104A 332-057B 1PTF0403116
SUPPORTER,PCB CPT SET A48ECR141X(S/S, DARK W/ITC LGE SPEAKER,FULLRANGE C122P02K1459 8 OHM 1 COIL,DEGAUSSING CU 20Ó 60TURN 15 OHM LEAD SET,CPT EARTH POWER CORD(W/HOLD,HOUSING,L=200,4.0 CABINET ASSEMBLY BUTTON,CONTROL SPRING,KNOB BUTTON,POWER BACK COVER ASSEMBLY PWB ASSY,MAIN IC,CDS SENSOR MODULE(P1201-04) SCREW ASSY,HEXAGON HEAD SCREW,TAP TITE(P) D4.0 L16.0
- 23 -
EXPLODED VIEW : 20/21F60KX
943 150 153
913 170
400
112
174
OPTION
104
520
300
310
330 320 120
- 24 -
EXPLODED VIEW PARTS LIST
PART NO LOCA. NO 20" 21"
The components identified by mark critical for safety. Replace only with part number specified.
are
DESCRIPTIONS
104 112 120 150 170 174 300 310 320 330 400 520
343-B52A 112-C20S 120-C93G 150-D02Y 170-A01D 174-009E 3091V00205E 5020V00174E 320-070U 5020V00175B 3809V00153D 6871VMM809L 6871VMM714S
343-B52A 112-C21G 120-C93G 150-D02X 170-A01D 174-009E 3091V00206E 5020V00181C 320-070U 5020V00182B 3809V00153D 6871VMM809U 332-057J 1PTF0403116
SUPPORTER,PCB CPT SET SPEAKER,GENERAL COIL,DEGAUSSING LEAD SET,CPT EARTH POWER CORD(W/HOLD,HOUSING,L=200,4.0 CABINET ASSEMBLY BUTTON,CONTROL SPRING,COIL BUTTON,POWER BACK COVER ASSEMBLY PWB ASSY,MAIN PWB ASSY,MAIN F60KX SCREW ASSY,HEXAGON HEAD SCREW,TAP TITE(P) D4.0 L16.0
913 943
332-057J 1PTF0403116
- 25 -
The components identified by mark are critical for safety. Replace only with part number specified.
REPLACEMENT PARTS LIST
DESCRIPTION LOCA. NO ZD501 ZD601 PART NO 0DZ820009BF 0DZ910009BD 0DZ750009BE DESCRIPTION DIODE,ZENER GDZJ8.2B TP GRANDE DO34 0.5W DIODE,ZENER GDZJ9.1B TP GRANDE DO34 0.5W DIODE,ZENER GDZJ7.5B TP GRANDE DO34 0.5W
LOCA. NO
PART NO
IC
IC01 Ò IC02 IC03 IC130 IC301 IC602 IC603 IC621 IC631 IC661 IC662 IC801 IC802 IC803 IC804 IC842 IC844 IC901 0IZZVC0020D 0IZZVC0020G 0ISG111733B 0IAL241600B 0IKE780500Q 0ISA784070A 0ISG729700A 0IFA754207A 0ISG200600A 0IMCRPH010A 0IIT341000J 0IFA753307A 0ILI817000G 0ILI817000G 0ISK665413C 0ISK110000A 0IMCRUK002A 0IMCRKE001A 0IPH610700A IC,PHILIPS 64P ST (EU)TXT 019A IC,PHILIPS 64P ST (EU)W/O TXT 019 IC,LD1117V33C 3SIP ST REGULATOR IC,AT24C16-10PC 8D EEPROM 16K IC,KIA7805API 3P TO-220 ST REGULA IC,LA7840 7S VERTICAL IC,TDA7297 15P,SIP BK 2CH 15W DUA IC,KA75420ZTA(KA7542ZTA) 3P,TO-92 IC,TDA2006 5Z IC,TDA9859 PHILIPS 32P SDIP ST UN IC,MSP3410D-C5 52P SDIP BK MULTI IC,KA75330ZTA(KA7533ZTA) 3P,TO-92 IC,LTV817M-VB 4P,DIP BK PHOTO COU IC,LTV817M-VB 4P,DIP BK PHOTO COU IC,STR-F6654R(LF1352) 5 SIP BK ST IC,SE110N(LF12) 3P 110V ERROR AMP IC,S78DL05 AUK 3P,TO92 TP 5V-REGU IC,KIA78R08PI KEC 4PIN,TO220IS-4 IC,TDA6107Q SIP9 BK VIDEO OUT AMP
ZD901
TRANSISTOR
Q01 Q102 Q301 Q402 Q442 Q551 Q552 Q571 Q621 Q651 Q653 Q671 Q672 Q801 Q802 Q806 0TR198009BA 0TR319709AB 0TR198009BA 0TR570200AA 0TR233109AA 0TR198009BA 0TR198009BA 0TR198009BA 0TR534309AA 0TR534309AA 0TR198009BA 0TR198009BA 0TR198009BA 0TR102009AB 0TR102009AB 0TR102009AB TR,2SA1980Y TP AUK - TR,KTC3197,TP(KTC388A),KEC TR,2SA1980Y TP AUK - TR,KSD5702 BK SAMSUNG TO3PF H-OUT TR,KSC2331-Y TP SAMSUNG TO-92L TR,2SA1980Y TP AUK - TR,2SA1980Y TP AUK - TR,2SA1980Y TP AUK - TR,2SC5343Y TP AUK - TR,2SC5343Y TP AUK - TR,2SA1980Y TP AUK - TR,2SA1980Y TP AUK - TR,2SA1980Y TP AUK - TR,KRC102M,TP(KRC1202),KEC TR,KRC102M,TP(KRC1202),KEC TR,KRC102M,TP(KRC1202),KEC
DIODE
D101 D301 D401 D441 D442 D443 D501 D571 D802 D803 D804 D805 D806 D807 D808 D814 D815 D816 D824 D901 D902 D903 D904 DB801 LD01 ZD01 ZD101 ZD441 ZD442 ZD443 0DD414809ED 0DD400509AA 0DD150009CA 0DD060009AC 0DD060009AC 0DD060009AC 0DD414809ED 0DD414809ED 0DD100009AM 0DD414809ED 0DD360009AA 0DD200009AH 0DD100009AM 0DD300009AC 0DD060009AC 0DD420000BB 0DD420000BB 0DD060009AC 0DD420000BB 0DR210009AC 0DR210009AC 0DR210009AC 0DR140049AC 0DD260000BB 4930V00183B 0DZ910009AJ 0DZ510009AK 0DZ620009AK 0DZ820009BF 0DZ330009DG DIODE,1N4148 TA DIODE,RECTIFIER 1N4005 GP TA DIODE,RECTIFIER RGP15J,TP(52MM),GI DIODE,TVR06J 0.6A/600V 250NS TP G.I DIODE,TVR06J 0.6A/600V 250NS TP G.I DIODE,TVR06J 0.6A/600V 250NS TP G.I DIODE,1N4148 TA DIODE,1N4148 TA DIODE,RECTIFIER EU1ZV(1) TP SANKEN DIODE,1N4148 TA DIODE,BYW36 TP (2A/600V) TELEFUNKEN DIODE,RU2AMV(1) TP SANKEN DIODE,RECTIFIER EU1ZV(1) TP SANKEN DIODE,RECTIFIER RU3AMV(1) TP SANKEN DIODE,TVR06J 0.6A/600V 250NS TP G.I DIODE,D4L20U SHINDENGEN DIODE,D4L20U SHINDENGEN DIODE,TVR06J 0.6A/600V 250NS TP G.I DIODE,D4L20U SHINDENGEN DIODE,RECTIFIER BAV21 DIODE,RECTIFIER BAV21 DIODE,RECTIFIER BAV21 DIODE,RECTIFIER 1N4004A T-81 DIODE,RECTIFIER BRIDGE D2SBA60(STK) HOLDER LED MODULE ASSY . 4PIN DIODE,ZENER MTZJ9.1B TP ROHM-K DO34 0.5W DIODE,ZENER GDZJ5.1B TP GRANDE DO34 0.5W DIODE,ZENER GDZJ6.2B TP GRANDE DO34 0.5W DIODE,ZENER GDZJ8.2B TP GRANDE DO34 0.5W DIODE,ZENER GDZJ33B TP GRANDE DO34 0.5W C01 C02 C03 C04 C05 C07 C21 C51 C101 C102 C107 C109 C110 C111 C112 C113 C121 C131 C211 C201 C202 C204 C206 C207 C208 C209 C210 C212 C253 Ò 0CN1020K519 0CN1030F679 0CE107DD618 0CC2200K415 0CC2200K415 0CE107DD618 0CE107DD618 0CN1030F679 0CN1030F679 0CE106DF618 0CE107DD618 0CE476DK618 0CN1030F679 0CN1030F679 0CN1030F679 0CN1020K519 0CN1010K519 0CE107DD618 0CN1010K519 0CE227DD618 0CN4710K519 0CN4710K519 0CN4710K519 0CN4710K519 0CE226DF618 0CE226DF618 0CN1030F679 0CN4710K519 0CN1030F679 0CN1020K519
CAPACITOR
1000P 50V K B TA52 10000P 16V M Y TA52 100UF STD 10V M FL TP5 22P 50V J NPO TS 22P 50V J NPO TS 100UF STD 10V M FL TP5 100UF STD 10V M FL TP5 10000P 16V M Y TA52 10000P 16V M Y TA52 10UF STD 16V M FL TP5 100UF STD 10V M FL TP5 47UF STD 50V M FL TP5 10000P 16V M Y TA52 10000P 16V M Y TA52 10000P 16V M Y TA52 1000P 50V K B TA52 100P 50V K B TA52 100UF STD 10V M FL TP5 100P 50V K B TA52 220UF STD 10V M FL TP5 470P 50V K 470P 50V K B TA52 470P 50V K B TA52 470P 50V K 22UF STD 16V M FL TP5 22UF STD 16V M FL TP5 10000P 16V M Y TA52 470P 50V K 10000P 16V M Y TA52 1000P 50V K B TA52
- 26 -
For Capacitor & Resistors, the charactors at 2nd and 3rd digit in the P/No. means as follows;
CC, CX, CK, CN : Ceramic CQ : Polyestor CE : Electrolytic
RD : Carbon Film RS : Metal Oxide Film RN : Metal Film RF : Fusible
The components identified by mark are critical for safety. Replace only with part number specified.
LOCA. NO C255 Ò C260 C301 C302 C303 C304 C307 C401 C402 C403 Ò(20Ó) C404 C405 C441 C443 C444 C446 C447 C449 C452 C501 C502 C503 C504 C505 C506 C507 C509 C511 C512 C513 C514 C515 C516 C517 C524 C529 C530 C532 C534 C538 C540 C541 C542 C548 C549 C551 C561 C573 C574 C594
PART NO 0CN1030F679 0CN1020K519 0CE226DF618 0CQ1041N509 0CQ3931N509 0CK1810W515 0CE107DJ618 0CQ6821N509 181-013P 0CE475DP618 181-015E 181-015J 0CK8210W515 181-091U 0CQ1531N509 0CE477DH618 0CE475DR618 0CE477DH618 0CQ3321N509 181-009V 0CE106DK618 0CF2241L438 0CN1030F679 0CE107DD618 0CE225DK618 0CQ2221N509 0CE105DK618 0CQ2221N509 0CE106DF618 0CE105DK618 0CN1020K519 0CN1020K519 0CQ1041N455 0CQ2231N509 0CQ3321N509 0CE106DF618 0CN1030F679 0CE225DK618 0CQ1041N509 0CE225DK618 0CN1030F679 0CF4741L438 0CN2230H949 0CN2230H949 0CN2230H949 0CN8210K519 0CQ4721N509 0CX4700K409 0CE107DD618 0CE476DF618 0CQ1021N509 0CQ1041N509
DESCRIPTION 10000P 16V M Y TA52 1000P 50V K 22UF STD 16V M FL TP5 0.1U 100V K POLY TP
LOCA. NO C601 C602 C603 C605 C606 C607 C612
PART NO 0CE226DF618 0CF2241L438 0CQ4721N509 0CQ4721N509 0CF2241L438 0CN1030F679 0CE477DH618 0CE477DJ618 0CQ6821N509 0CE225DK618 0CE106DH618 0CE477DJ618 0CQ1041N509 0CE226DK618 0CF4741L438 0CF4741L438 0CE107DD618 0CN1030F679 0CE106DF618 0CQ6821N509 0CF1541L438 0CQ5621N509 0CQ5621N509 0CF1541L438 0CQ6821N509 0CQ5621N509 0CF4741L438 0CQ4731N509 0CF4741L438 0CF4741L438 0CX4700K409 0CX4700K409 0CE227DD618 0CN1030F679 0CN1030F679 0CE335DK618 0CN3320F569 0CN3320F569 0CE226DF618 0CE106DF618 0CE107DD618 0CE106DF618 0CN1030F679 0CN1030F679 0CE106DF618 0CF3341L438 0CF3341L438 0CN1030F679 0CE106DF618 0CN1030F679 0CE106DF618 0CX5600K409
DESCRIPTION 22UF STD 16V M FL TP5 0.22UF D 63V 5% TP 5 M/PE NI 0.0047U 100V K POLY TP 0.0047U 100V K POLY TP 0.22UF D 63V 5% TP 5 M/PE NI 10000P 16V M Y TA52 470UF STD 25V M FL TP5 470UF STD 35V 20% FL TP * MONO 0.0068U 100V K POLY TP
0.0390UF 100V K PE TP 180P 500V K B TS
100UF STD 35V M FL TP5 0.0068U 100V K POLY MPP 400V 0.33UF J 4.7UF STD 160V 20% FL TP 5 MPP 1600V 0.0068UF H MPP 1600V 0.0086UF H 820P 500V K B TS 2KV R 221K 0.015U 100V K POLY TP TP
Ò C621 C622 C623 C624 C625 C626 C631 C632 C633 C634 C635 C636 C637 C638 C639 C640 C641 C642 C643
2.2UF STD 50V 20% FL TP 5 10UF STD 25V M FL TP5 470UF STD 35V 20% FL TP 5 0.1U 100V K POLY TP
22UF STD 50V M FL TP5 0.47UF D 63V 5% TP 5 M/PE NI 0.47UF D 63V 5% TP 5 M/PE NI 100UF STD 10V M FL TP5 10000P 16V M Y TA52 10UF STD 16V M FL TP5 0.0068U 100V K POLY TP
470UF STD 25V M FL TP5 4.7UF STD 250V 20% FL TP 5 470UF STD 25V M FL TP5 0.0033U 100V K POLY PP 200V 0.047UF K 10UF STD 50V M FL TP5 0.22UF D 63V 5% TP 5 M/PE NI 10000P 16V M Y TA52 100UF STD 10V M FL TP5 2.2UF STD 50V 20% FL TP 5 0.0022U 100V K POLY 1UF STD 50V M FL TP5 0.0022U 100V K POLY 10UF STD 16V M FL TP5 1UF STD 50V M FL TP5 1000P 50V K B TA52 1000P 50V K B TA52 0.1000UF 100V J PP NI FM7.5 0.022U 100V K POLY 0.0033U 100V K POLY 10UF STD 16V M FL TP5 10000P 16V M Y TA52 2.2UF STD 50V 20% FL TP 5 0.1U 100V K POLY TP TP TP TP TP TP
0.15UF D 63V 5% TP 5 M/PE NI 0.0056U 100V K POLY 0.0056U 100V K POLY TP TP
0.15UF D 63V 5% TP 5 M/PE NI 0.0068U 100V K POLY 0.0056U 100V K POLY TP TP
0.47UF D 63V 5% TP 5 M/PE NI 0.047U 100V K POLY TP 0.47UF D 63V 5% TP 5 M/PE NI 0.47UF D 63V 5% TP 5 M/PE NI 47P 50V J SL TA52 47P 50V J SL TA52 220UF STD 10V M FL TP5 10000P 16V M Y TA52 10000P 16V M Y TA52 3.3UF STD 50V 20% FL TP 5 3300P 16V K X TA52 3300P 16V K X TA52 22UF STD 16V M FL TP5 10UF STD 16V M FL TP5 100UF STD 10V M FL TP5 10UF STD 16V M FL TP5 10000P 16V M Y TA52 10000P 16V M Y TA52 10UF STD 16V M FL TP5 0.33UF D 63V 5% TP 5 M/PE NI 0.33UF D 63V 5% TP 5 M/PE NI 10000P 16V M Y TA52 10UF STD 16V M FL TP5 10000P 16V M Y TA52 10UF STD 16V M FL TP5 56P 50V J SL TA52
C644 C645 C646 C661 C662 C663 C664 C665 C666 C667 C668 C669 C670 C671 C672 C673 C674 C675 C678 C679 C680 C681 C684 C685 C686
2.2UF STD 50V 20% FL TP 5 10000P 16V M Y TA52 0.47UF D 63V 5% TP 5 M/PE NI 22000P 25V Z FTA52 22000P 25V Z FTA52 22000P 25V Z FTA52 820P 50V K B TA52
0.0047U 100V K POLY TP 47P 50V J SL TA52 100UF STD 10V M FL TP5 47UF STD 16V M FL TP5 0.001U 100V K POLY 0.1U 100V K POLY TP TP
- 27 -
The components identified by mark are critical for safety. Replace only with part number specified.
For Capacitor & Resistors, the charactors at 2nd and 3rd digit in the P/No. means as follows;
CC, CX, CK, CN : Ceramic CQ : Polyestor CE : Electrolytic
RD : Carbon Film RS : Metal Oxide Film RN : Metal Film RF : Fusible
LOCA. NO C687 C688 C689 C690 C801 C802 C803 C804 C806 C807 C808 C809 C811 C812 Ò C813 C815 C816 C817 C818 C819 C820 C821 C823 C825 C828 C829 C830 C831 C834 C841 C901 C902 C903 C904 C905
PART NO 0CX5600K409 0CX5600K409 0CC0200K115 0CC0200K115 0CE107BJ618 181-091U 0CK4710W515 0CQ1041N509 181-001V 0CK10201515 0CK10201515 0CQZVBK002C 181-120K 0CE108DJ618 0CE108DH618 0CK4710W515 0CK4710W515 0CN1030F679 0CK4710W515 0CE107BH618 181-091Y 0CE227DP650 181-120N 0CK4710K515 181-091P 0CE107DF618 0CF1021047A 0CE475DK618 0CE108BF618 0CE476CP618 0CE477DD618 0CE475DR618 0CQ1044R539 0CK12202510 0CE475DR618 0CN5610K519
DESCRIPTION 56P 50V J SL TA52 56P 50V J SL TA52 2P 2P 50V 50V D NP0 TS D NP0 TS
LOCA. NO L251 L252 L402 Ò(20Ó) L501 L502 L503
PART NO 0LA0102K119 0LA0102K119 150-L01Z 150-L02C 0LA0102K119 0LA0102K119 0LA0102K119 0LA0102K119 0LA0681K119 0LA0102K119 0LA0102K119 0LA0102K119 150-C02F 0LA0101K119 0LA0681K119 0LA0681K119 0LA0681K119 6174Z-6040C 6170VC0003C 151-A13P 6170VMCB01K
DESCRIPTION INDUCTOR,10UH K 2.3*3.4 TP INDUCTOR,10UH K COIL,LINEARITY 97UH COIL,LINEARITY 170UH INDUCTOR,10UH K 2.3*3.4 TP INDUCTOR,10UH K 2.3*3.4 TP INDUCTOR,10UH K 2.3*3.4 TP INDUCTOR,10UH K 2.3*3.4 TP INDUCTOR,6.8UH K 2.3*3.4 TP INDUCTOR,10UH K INDUCTOR,10UH K INDUCTOR,10UH K COIL,CHOKE 82UH R1217 INDUCTOR,1.0UH K 2.3*3.4 TP INDUCTOR,6.8UH K 2.3*3.4 TP INDUCTOR,6.8UH K 2.3*3.4 TP INDUCTOR,6.8UH K 2.3*3.4 TP FBT FTMPNG1 -6040C TRANSFORMER,H-DRIVER DRUM 10*12 TRANSFORMER,SMPS EC4215 265UH F6654 TRANSFORMER,SMPS EER4215 340UH
100UF KME 35V M FL TP5 2KV R 221K TP7.5 470PF 500V K B TR 0.1U 100V K POLY TP
L506 L551 L661 L662 L663 L801 R443 R545 R546 R547 T401 T402 T802 Ò
CE 450V 220UF M LUG(85) 1000P 1KV K B TS 1000P 1KV K B TS A.C 275V 0.22UF K (S=22.5) 2200PF 4KV M E FMTW LEAD 4.5 1000UF STD 35V M FL TP5 1000UF STD 25V M FL TP5 470PF 500V K B TR 470PF 500V K B TR 10000P 16V M Y TA52 470PF 500V K B TR 100UF KME 25V M FL TP5 2KV R 681K TP7.5 220UF STD 160V M FM7.5 BULK 1000PF 4KV M E FMTW LEAD4.5 470PF 50V K B TR 1KV SL 271J TP5 100UF STD 16V M FL TP5 1000PF D 800V 5% TP 7.5 M/PP N 4.7UF STD 50V 20% FL TP 5 1000UF KME 16V M FL TP5 47UF SHL,SD 160V 20% FL TP 5 470UF STD 10V M FL TP5 4.7UF STD 250V 20% FL TP 5 0.1UF TE 250V K M/PE NI TP5 1200P 2KV K B S 4.7UF STD 250V 20% FL TP 5 560P 50V K B TA52
RESISTOR
C258 C259 C546 FR441 FR442 Ò(20Ó) FR443 FR802 FR803 J30 J33 J39 J101 J149 J154 L01 L10 L251 L252 R01 R03 R04 R05 R06 R07 R09 R10 R12 R14 0RD4702F609 0RD4702F609 0RD1103F609 0RF0470J607 0RF0121K607 0RF0101J607 0RF0470J607 0RF0470H609 0RF0470K607 0RD2200F609 0RD2200F609 0RD2200F609 0RD4702F609 0RD1001F609 0RD1101F609 0RD1500F609 0RD0102F609 0RD2002F609 0RD2002F609 0RD1002F609 0RD1000F609 0RD3301F609 0RD3301F609 0RD4701F609 0RD4701F609 0RD1000F609 0RD1000F609 0RD1001F609 0RD1603F609 47K OHM 1/6 W 5.00% TA52 47K OHM 1/6 W 5.00% TA52 110K OHM 1/6 W 5.00% TA52 0.47 OHM 1 W 5.00% TA62 1.2 OHM 2 W 5.00% TA62 1 OHM 1 W 5.00% TA62 0.47 OHM 1 W 5.00% TA62 0.47 OHM 1/2 W 5.00% TA52 0.47 OHM 2 W 5.00% TA62 220 OHM 1/6 W 5.00% TA52 220 OHM 1/6 W 5.00% TA52 220 OHM 1/6 W 5.00% TA52 47K OHM 1/6 W 5.00% TA52 1K OHM 1/6 W 5.00% TA52 1.1K OHM 1/6 W 5.00% TA52 150 OHM 1/6 W 5.00% TA52 10 OHM 1/6 W 5.00% TA52 20K OHM 1/6 W 5.00% TA52 20K OHM 1/6 W 5.00% TA52 10K OHM 1/6 W 5.00% TA52 100 OHM 1/6 W 5.00% TA52 3.3K OHM 1/6 W 5.00% TA52 3.3K OHM 1/6 W 5.00% TA52 4.7K OHM 1/6 W 5.00% TA52 4.7K OHM 1/6 W 5.00% TA52 100 OHM 1/6 W 5.00% TA52 100 OHM 1/6 W 5.00% TA52 1K OHM 1/6 W 5.00% TA52 160K OHM 1/6 W 5.00% TA52
FUSE
F801 F812 FR803 0FT4001B53C 131-096N 131-096N FUSE,TIME LAG 4000MA 250V 5.2X20 FUSE,FAST BLOE 4000MA 125V 2.5X7.6 FUSE,FAST BLOE 4000MA 125V 2.5X7.6
COIL & TRANSFORMER
J57 L04 L05 L102 L202 L203 L204 L205 L210 0LA0102K119 0LA1000K119 0LA0102K119 0LA0680K119 0LA0102K119 0LA0102K119 0LA0102K119 0LA0102K119 0LA0102K119 INDUCTOR,10UH K 2.3*3.4 TP INDUCTOR,100UH K 2.3*3.4 TP INDUCTOR,10UH K 2.3*3.4 TP INDUCTOR,0.68UH K 2.3*3.4 TP INDUCTOR,10UH K INDUCTOR,10UH K 2.3*3.4 TP INDUCTOR,10UH K INDUCTOR,10UH K 2.3*3.4 TP INDUCTOR,10UH K 2.3*3.4 TP
- 28 -
For Capacitor & Resistors, the charactors at 2nd and 3rd digit in the P/No. means as follows;
CC, CX, CK, CN : Ceramic CQ : Polyestor CE : Electrolytic
RD : Carbon Film RS : Metal Oxide Film RN : Metal Film RF : Fusible
The components identified by mark are critical for safety. Replace only with part number specified.
LOCA. NO R16 R17 R18 R19 R21 R22 R23 R25 R26 R27 R29 R41 R51 R52 R101 R102 R103 R105 R106 R107 R108 R109 R110 R111 R112 R113 R114 R201 Ò R204 R205 R206 R207 R208 R251 Ò R254 R255 R301 R302 Ò(20Ó) R304 R305 R306 R307 Ò(20Ó) R310 R311 R312 R313 R401 R402
PART NO 0RD4701F609 0RD1000F609 0RD1203F609 0RD1000F609 0RD2201F609 0RD3902F609 0RD2200F609 0RD1201F609 0RD2201F609 0RD4701F609 0RD1201F609 0RD6200F609 0RD1000F609 0RD1000F609 0RD1002F609 0RD1202F609 0RD1802F609 0RD1000F609 0RD1000F609 0RS0272J607 0RD0392F609 0RD0562F609 0RD1201F609 0RD3601F609 0RD1000F609 0RD6800F609 0RD0272F609 0RD0912F609 0RD0682F609 0RD0752F609 0RD0822F609 0RD0822F609 0RD0822F609 0RD1001F609 0RD1300F609 0RD0822F609 0RD2200H609 0RD2200H609 0RD0101F609 0RN1501F409 0RN1201F409 0RD0221H609 0RD0221H609 0RS2700K607 0RD1501F609 0RD1201F609 0RD1801F609 0RD4701H609 0RD2201F609 0RD1002F609 0RD1501H609 0RS2702K607
DESCRIPTION 4.7K OHM 1/6 W 5.00% TA52 100 OHM 1/6 W 5.00% TA52 120K OHM 1/6 W 5.00% TA52 100 OHM 1/6 W 5.00% TA52 2.2K OHM 1/6 W 5.00% TA52 39K OHM 1/6 W 5.00% TA52 220 OHM 1/6 W 5.00% TA52 1.2K OHM 1/6 W 5.00% TA52 2.2K OHM 1/6 W 5.00% TA52 4.7K OHM 1/6 W 5.00% TA52 1.2K OHM 1/6 W 5.00% TA52 620 OHM 1/6 W 5.00% TA52 100 OHM 1/6 W 5.00% TA52 100 OHM 1/6 W 5.00% TA52 10K OHM 1/6 W 5.00% TA52 12K OHM 1/6 W 5.00% TA52 18K OHM 1/6 W 5.00% TA52 100 OHM 1/6 W 5.00% TA52 100 OHM 1/6 W 5.00% TA52 27 OHM 1 W 5.00% TA62 39 OHM 1/6 W 5.00% TA52 56 OHM 1/6 W 5.00% TA52 1.2K OHM 1/6 W 5.00% TA52 3.6K OHM 1/6 W 5.00% TA52 100 OHM 1/6 W 5.00% TA52 680 OHM 1/6 W 5.00% TA52 27 OHM 1/6 W 5.00% TA52 91 OHM 1/6 W 5.00% TA52 68 OHM 1/6 W 5.00% TA52 75 OHM 1/6 W 5.00% TA52 82 OHM 1/6 W 5.00% TA52 82 OHM 1/6 W 5.00% TA52 82 OHM 1/6 W 5.00% TA52 1K OHM 1/6 W 5.00% TA52 130 OHM 1/6 W 5.00% TA52 82 OHM 1/6 W 5.00% TA52 220 OHM 1/2 W 5.00% TA52 220 OHM 1/2 W 5.00% TA52 1 OHM 1/6 W 5.00% TA52 1.5K OHM 1/6 W 1.00% TA52 1.2K OHM 1/6 W 1.00% TA52 2.2 OHM 1/2 W 5.00% TA52 2.2 OHM 1/2 W 5.00% TA52 270 OHM 2 W 5.00% TA62 1.5K OHM 1/6 W 5.00% TA52 1.2K OHM 1/6 W 5.00% TA52 1.8K OHM 1/6 W 5.00% TA52 4.7K OHM 1/2 W 5.00% TA52 2.2K OHM 1/6 W 5.00% TA52 10K OHM 1/6 W 5.00% TA52 1.5K OHM 1/2 W 5.00% TA52 27K OHM 2 W 5.00% TA62
LOCA. NO R442 R444 R446 R447 Ò(20Ó) R450 R451 R453 Ò(20Ó) R455 R456 Ò(20Ó) R501 R504 R505 R506 R518 R521 R522 R523 R524 R525 R526 R537 R538 R539 R540 R542 R544 R551 R552 R553 R554 R556 R559 R572 R573 R601 R602 R604 R606 R608 R609 R610 R611 R621 R622 R623 R624 R625 R626 R627
PART NO 0RD5100H609 0RD0392H609 0RD1001F609 0RD3001F609 0RD1001F609 0RD4701H609 0RD1200H609 0RS4702H609 0RS3302H609 0RS2702K607 0RS2702H609 0RS5102H609 0RD2202F609 0RN3902F409 0RD6800F609 0RD1001F609 0RD3302F609 0RD1000F609 0RD2702F609 0RD1003F609 0RD3001F609 0RD3900F609 0RD2001F609 0RD1000F609 0RD1000F609 0RD1000F609 0RD1000F609 0RD1002F609 0RD2701F609 0RD1200F609 0RD1200F609 0RD3300F609 0RD4701F609 0RD1500F609 0RD1800F609 0RD5600F609 0RD2403F609 0RD4701F609 0RD1002F609 0RD3301F609 0RD7501F609 0RD3301F609 0RD7501F609 0RD4702F609 0RD4702F609 0RD9102F609 0RD6801F609 0RD1003F609 0RD1003F609 0RD1003F609 0RD5101F609 0RD3301F609
DESCRIPTION 510 OHM 1/2 W 5.00% TA52 39 OHM 1/2 W 5.00% TA52 1K OHM 1/6 W 5.00% TA52 3K OHM 1/6 W 5.00% TA52 1K OHM 1/6 W 5.00% TA52 4.7K OHM 1/2 W 5.00% TA52 120 OHM 1/2 W 5.00% TA52 47K OHM 1/2 W 5.00% TA52 33K OHM 1/2 W 5.00% TA52 27K OHM 2 W 5.00% TA62 27K OHM 1/2 W 5.00% TA52 51K OHM 1/2 W 5.00% TA52 22K OHM 1/6 W 5.00% TA52 39K OHM 1/6 W 1.00% TA52 680 OHM 1/6 W 5.00% TA52 1K OHM 1/6 W 5.00% TA52 33K OHM 1/6 W 5.00% TA52 100 OHM 1/6 W 5.00% TA52 27K OHM 1/6 W 5.00% TA52 100K OHM 1/6 W 5.00% TA52 3K OHM 1/6 W 5.00% TA52 390 OHM 1/6 W 5.00% TA52 2K OHM 1/6 W 5.00% TA52 100 OHM 1/6 W 5.00% TA52 100 OHM 1/6 W 5.00% TA52 100 OHM 1/6 W 5.00% TA52 100 OHM 1/6 W 5.00% TA52 10K OHM 1/6 W 5.00% TA52 2.7K OHM 1/6 W 5.00% TA52 120 OHM 1/6 W 5.00% TA52 120 OHM 1/6 W 5.00% TA52 330 OHM 1/6 W 5.00% TA52 4.7K OHM 1/6 W 5.00% TA52 150 OHM 1/6 W 5.00% TA52 180 OHM 1/6 W 5.00% TA52 560 OHM 1/6 W 5.00% TA52 240K OHM 1/6 W 5.00% TA52 4.7K OHM 1/6 W 5.00% TA52 10K OHM 1/6 W 5.00% TA52 3.3K OHM 1/6 W 5.00% TA52 7.5K OHM 1/6 W 5.00% TA52 3.3K OHM 1/6 W 5.00% TA52 7.5K OHM 1/6 W 5.00% TA52 47K OHM 1/6 W 5.00% TA52 47K OHM 1/6 W 5.00% TA52 91K OHM 1/6 W 5.00% TA52 6.8K OHM 1/6 W 5.00% TA52 100K OHM 1/6 W 5.00% TA52 100K OHM 1/6 W 5.00% TA52 100K OHM 1/6 W 5.00% TA52 5.1K OHM 1/6 W 5.00% TA52 3.3K OHM 1/6 W 5.00% TA52
- 29 -
The components identified by mark are critical for safety. Replace only with part number specified.
For Capacitor & Resistors, the charactors at 2nd and 3rd digit in the P/No. means as follows;
CC, CX, CK, CN : Ceramic CQ : Polyestor CE : Electrolytic
RD : Carbon Film RS : Metal Oxide Film RN : Metal Film RF : Fusible
LOCA. NO R628 R631 R632 R633 R634 R651 Ò R652 R655 R657 Ò R660 R662 R663 R664 R665 R666 R667 R670 Ò R671 R801 R802 R803 R804 R805 Ò R806 R808 R809 R812 R813 R815 R816 R903 R904 R905 R906 R907 R908 R909 R910 R911 R912 RC801
PART NO 0RD0331H609 0RD1302F609 0RD1000F609 0RD1000F609 0RD1302F609 0RD1500F609 0RD4700F609 0RD2200F609 0CN1030F679 0RD2201F609 0RD4300F609 0RD4702F609 0RD1000F609 0RD1000F609 0RD1002F609 0RD3901F609 0RD3901F609 0RD0102F609 0RD1001F609 0RD2000F609 0RD1001F609 0RD2701F609 0RD2201F609 0RD1001F609 0RD4701F609 180-A01P 180-A01M 0RD2401F609 0RD4701F609 0RS4702K607 0RK8204H609 0RD1002F609 0RD0751H609 0RD2001F609 0RD2200F609 0RD2200F609 0RD2200F609 0RD1000F609 0RD1000F609 0RD1000F609 0RS1501H609 0RS1501H609 0RS1501H609 0RD2204H609 180-822N
DESCRIPTION 3.3 OHM 1/2 W 5.00% TA52 13K OHM 1/6 W 5.00% TA52 100 OHM 1/6 W 5.00% TA52 100 OHM 1/6 W 5.00% TA52 13K OHM 1/6 W 5.00% TA52 150 OHM 1/6 W 5.00% TA52 470 OHM 1/6 W 5.00% TA52 220 OHM 1/6 W 5.00% TA52 10000P 16V M Y TA52 2.2K OHM 1/6 W 5.00% TA52 430 OHM 1/6 W 5.00% TA52 47K OHM 1/6 W 5.00% TA52 100 OHM 1/6 W 5.00% TA52 100 OHM 1/6 W 5.00% TA52 10K OHM 1/6 W 5.00% TA52 3.9K OHM 1/6 W 5.00% TA52 3.9K OHM 1/6 W 5.00% TA52 10 OHM 1/6 W 5.00% TA52 1K OHM 1/6 W 5.00% TA52 200 OHM 1/6 W 5.00% TA52 1K OHM 1/6 W 5.00% TA52 2.7K OHM 1/6 W 5.00% TA52 2.2K OHM 1/6 W 5.00% TA52 1K OHM 1/6 W 5.00% TA52 4.7K OHM 1/6 W 5.00% TA52 0.13 OHM 2 W 5% TA62 RWR 0.22 OHM 2 W 5% TA62 RWR 2.4K OHM 1/6 W 5.00% TA52 4.7K OHM 1/6 W 5.00% TA52 47K OHM 2 W 5.00% TA62 8.2M OHM 1/2 W 5.00% TA52 10K OHM 1/6 W 5.00% TA52 7.5 OHM 1/2 W 5.00% TA52 2K OHM 1/6 W 5.00% TA52 220 OHM 1/6 W 5.00% TA52 220 OHM 1/6 W 5.00% TA52 220 OHM 1/6 W 5.00% TA52 100 OHM 1/6 W 5.00% TA52 100 OHM 1/6 W 5.00% TA52 100 OHM 1/6 W 5.00% TA52 1.5K OHM 1/2 W 5.00% TA52 1.5K OHM 1/2 W 5.00% TA52 1.5K OHM 1/2 W 5.00% TA52 2.2M OHM 1/2 W 5.00% TA52 RWR 7W 1.0 OHM J PD
LOCA. NO SW06 SW801
PART NO 140-315A 6600VM2002A
DESCRIPTION SWITCH,TACT SKHV17910B LG C&D NON 12V SWITCH,PUSH SDKEA3 IEC 250V 8A HORIZO
FILTER & CRYSTAL
FB801 FB802 FB803 L201 L611 T551 T552 T801 X01 X661 Z102 Z551 125-022R 125-022R 125-022R 125-022R 125-022R 166-C02D 166-C04C 150-F06J 156-A02B 156-A02M 6200VQS001L 166-B02E FILTER,BI3857 FEELUX 5.7X3.6MM AXIAL FILTER,BI3857 FEELUX 5.7X3.6MM AXIAL FILTER,BI3857 FEELUX 5.7X3.6MM AXIAL FILTER,BI3857 FEELUX 5.7X3.6MM FILTER,BI3857 FEELUX 5.7X3.6MM AXIAL FILTER,TPSRD6M00B00-A0 TPS6.0MB-TF21 FILTER,TPWRD5M50B02-A0 TPWA02B-TF21 M FILTER,SQE2930 18MH PHY TURN RESONATOR,CRYSTAL HC49U KJE RADIAL RESONATOR,CRYSTAL KJE RADIAL 18.432MHZ FILTER,SAW OFWK2971M 39.90MHZ INT FILTER,BAND PASS SFSRH6M50CF00-A0
ACCESSO