Text preview for : DMC-TZ5.pdf part of Panasonic DMC-TZ5 Digital Still Camera
Back to : DMC-TZ5.pdf | Home
ORDER NO.DSC0803021CE B26
Digital Camera
Model No.
DMC-TZ5P DMC-TZ5PC DMC-TZ5PL DMC-TZ5PR DMC-TZ5EB DMC-TZ5EE DMC-TZ5EF DMC-TZ5EG DMC-TZ5E DMC-TZ5SG DMC-TZ15GC DMC-TZ15GD DMC-TZ15GK DMC-TZ15GN DMC-TZ15GT DMC-TZ15GJ
VOL.1
Colours (S)....................Silver Type (except PR/GD) (K)....................Black Type (A)....................Blue Type (only DMC-TZ5P/PC/PL/PR/ EE/EG/E) (TA)....................Dark Brown Type (only DMC-TZ5EF/ EG/E) (T)....................Brown Type (only DMC-TZ5SG, DMCTZ15GC/GK/GJ)
© 2008 Matsushita Electric Industrial Co., Ltd. All rights reserved. Unauthorized copying and distribution is a violation of law.
2
TABLE OF CONTENTS
PAGE 1 Safety Precaution ------------------------------------------------ 4 1.1. General Guidelines---------------------------------------- 4 1.2. Leakage Current Cold Check--------------------------- 4 1.3. Leakage Current Hot Check (See Figure 1) -------- 4 1.4. How to Discharge the Capacitor on Flash PCB ----------------------------------------------------------- 5 2 Warning -------------------------------------------------------------- 6 2.1. Prevention of Electrostatic Discharge (ESD) to Electrostatic Sensitive (ES) Devices -------------- 6 2.2. How to Recycle the Lithium Ion Battery (U.S. Only) ---------------------------------------------------------- 6 2.3. Caution for AC Cord (For EB/GC/SG)---------------- 7 2.4. How to Replace the Lithium Battery ------------------ 8 3 Service Navigation ----------------------------------------------- 9 3.1. Introduction-------------------------------------------------- 9 3.2. General Description About Lead Free Solder (PbF)---------------------------------------------------------- 9 3.3. Important Notice 1:(Other than U.S.A. and Canadian Market) ----------------------------------------- 9 3.4. How to Define the Model Suffix (NTSC or PAL model) ------------------------------------------------------10 4 Specifications ----------------------------------------------------13 5 Location of Controls and Components ------------------15 6 Service Mode -----------------------------------------------------17 6.1. Error Code Memory Function--------------------------17 7 Service Fixture & Tools----------------------------------------20 7.1. Service Fixture and Tools-------------------------------20 7.2. When Replacing the Main PCB -----------------------20 7.3. Service Position-------------------------------------------20 8 Disassembly and Assembly Instructions ---------------22 8.1. Disassembly Flow Chart --------------------------------22 8.2. PCB Location ----------------------------------------------22 8.3. Disassembly Procedure---------------------------------23 8.4. Disassembly Procedure for the Lens ----------------28 8.5. Assembly Procedure for Lens -------------------------31 8.6. Removal of the CCD Unit-------------------------------35 8.7. Removal of the Zoom Motor Unit ---------------------36 8.8. Removal of the Focus Motor Unit --------------------36 8.9. The Applyment of grease Method --------------------37 9 Measurements and Adjustments---------------------------38 9.1. Matrix Chart for Replaced Part and Necessary Adjustment -------------------------------------------------38 10 Maintenace --------------------------------------------------------39 10.1. Cleaning Lens, Viewfinder and LCD Panel --------39 PAGE
3
1 Safety Precautions
1.1. General Guidelines 1.3.
1. IMPORTANT SAFETY NOTICE There are special components used in this equipment which are important for safety. These parts are marked by in the Schematic Diagrams, Circuit Board Layout, Exploded Views and Replacement Parts List. It is essential that these critical parts should be replaced with manufacturer's specified parts to prevent X-RADIATION, shock fire, or other hazards. Do not modify the original design without permission of manufacturer. An Isolation Transformer should always be used during the servicing of AC Adaptor whose chassis is not isolated from the AC power line. Use a transformer of adequate power rating as this protects the technician from accidents resulting in personal injury from electrical shocks. It will also protect AC Adaptor from being damaged by accidental shorting that may occur during servicing. When servicing, observe the original lead dress. It a short circuit is found, replace all parts which have been overheated or damaged by the short circuit. After servicing, see to it that all the protective devices such as insulation barriers, insulation papers shields are properly installed. After servicing, make the following leakage current checks to prevent the customer from being exposed to shock hazards.
Leakage Current Hot Check (See Figure 1)
2.
3.
4.
1. Plug the AC cord directly into the AC outlet. Do not use an isolation transformer for this check. 2. Connect a 1.5k, 10 W resistor, in parallel with a 0.15F capacitor, between each exposed metallic part on the set and a good earth ground, as shown in Figure 1. 3. Use an AC voltmeter, with 1 k/V or more sensitivity, to measure the potential across the resistor. 4. Check each exposed metallic part, and measure the voltage at each point. 5. Reverse the AC plug in the AC outlet and repeat each of the above measurements. 6. The potential at any point should not exceed 0.75 V RMS. A leakage current tester (Simpson Model 229 or equivalent) may be used to make the hot checks, leakage current must not exceed 1/2 mA. In case a measurement is outside of the limits specified, there is a possibility of a shock hazard, and the equipment should be repaired and rechecked before it is returned to the customer.
5.
1.2.
Leakage Current Cold Check
1. Unplug the AC cord and connect a jumper between the two prongs on the plug. 2. Measure the resistance value, with an ohmmeter, between the jumpered AC plug and each exposed metallic cabinet part on the equipment such as screwheads, connectors, control shafts, etc. When the exposed metallic part has a return path to the chassis, the reading should be between 1M and 5.2M. When the exposed metal does not have a return path to the chassis, the reading must be infinity.
Figure 1
4
1.4.
How to Discharge the Capacitor on Flash PCB
CAUTION: 1. Be sure to discharge the capacitor on FLASH PCB. 2. Be careful of the high voltage circuit on FLASH PCB when servicing. [Discharging Procedure] 1. Refer to the disassemble procedure and remove the necessary parts/unit. 2. Put the insulation tube onto the lead part of Resistor (ERG5SJ102:1k /5W). (an equivalent type of resistor may be used.) 3. Put the resistor between both terminals of capacitor on FLASH PCB for approx. 5 seconds. 4. After discharging confirm that the capacitor voltage is lower than 10V using a voltmeter.
Fig. F1
5
2 Warning
2.1. Prevention of Electrostatic Discharge (ESD) to Electrostatic Sensitive (ES) Devices
Some semiconductor (solid state) devices can be damaged easily by static electricity. Such components commonly are called Electrostatically Sensitive (ES) Devices.
The following techniques should be used to help reduce the incidence of component damage caused by electrostatic discharge (ESD).
1. Immediately before handling any semiconductor component or semiconductor-equipped assembly, drain off any ESD on your body by touching a known earth ground. Alternatively, obtain and wear a commercially available discharging ESD wrist strap, which should be removed for potential shock reasons prior to applying power to the unit under test. 2. After removing an electrical assembly equipped with ES devices, place the assembly on a conductive surface such as aluminum foil, to prevent electrostatic charge buildup or exposure of the assembly. 3. Use only a grounded-tip soldering iron to solder or unsolder ES devices. 4. Use only an antistatic solder removal device. Some solder removal devices not classified as can generate electrical charge sufficient to damage ES devices. 5. Do not use freon-propelled chemicals. These can generate electrical charges sufficient to damage ES devices. 6. Do not remove a replacement ES device from its protective package until immediately before you are ready to install it. (Most replacement ES devices are packaged with leads electrically shorted together by conductive foam, aluminum foil or comparable conductive material). 7. Immediately before removing the protective material from the leads of a replacement ES device, touch the protective material to the chassis or circuit assembly into which the device will be installed. CAUTION: Be sure no power is applied to the chassis or circuit, and observe all other safety precautions. 8. Minimize bodily motions when handling unpackaged replacement ES devices. (Otherwise harmless motion such as the brushing together of your clothes fabric or the lifting of your foot from a carpeted floor can generate static electricity (ESD) sufficient to damage an ES device).
2.2.
How to Recycle the Lithium Ion Battery (U.S. Only)
6
2.3.
2.3.1.
Caution for AC Cord (For EB/ GC/SG)
Information for Your Safety
2.3.2.1.
Important
The wires in this mains lead are coloured in accordance with the following code:
Blue Brown Neutral Live
IMPORTANT Your attention is drawn to the fact that recording of prerecorded tapes or discs or other published or broadcast material may infringe copyright laws. WARNING To reduce the risk of fire or shock hazard, do not expose this equipment to rain or moisture. CAUTION To reduce the risk of fire or shock hazard and annoying interference, use the recommended accessories only. FOR YOUR SAFETY DO NOT REMOVE THE OUTER COVER To prevent electric shock, do not remove the cover. No user serviceable parts inside. Refer servicing to qualified service personnel.
As the colours of the wires in the mains lead of this appliance may not correspond with the coloured markings identifying the terminals in your plug, proceed as follows: The wire which is coloured BLUE must be connected to the terminal in the plug which is marked with the letter N or coloured BLACK. The wire which is coloured BROWN must be connected to the terminal in the plug which is marked with the letter L or coloured RED. Under no circumstances should either of these wires be connected to the earth terminal of the three pin plug, marked with the letter E or the Earth Symbol.
2.3.2.
Caution for AC Mains Lead
For your safety, please read the following text carefully. This appliance is supplied with a moulded three-pin mains plug for your safety and convenience. A 5-ampere fuse is fitted in this plug. Should the fuse need to be replaced please ensure that the replacement fuse has a rating of 5 amperes and it is approved by ASTA or BSI to BS1362 Check for the ASRA mark or the BSI mark on the body of the fuse.
2.3.2.2.
Before Use
remove the Connector Cover as follows.
If the plug contains a removable fuse cover you must ensure that it is refitted when the fuse is replaced. If you lose the fuse cover, the plug must not be used until a replacement cover is obtained. A replacement fuse cover can be purchased from your local Panasonic Dealer. If the fitted moulded plug is unsuitable for the socket outlet in your home then the fuse should be removed and the plug cut off and disposed of safety. There is a danger of severe electrical shock if the cut off plug is inserted into any 13-ampere socket. If a new plug is to be fitted please observe the wiring code as shown below. If in any doubt, please consult a qualified electrician.
2.3.2.3.
How to Replace the Fuse
1. Remove the Fuse Cover with a screwdriver.
2. Replace the fuse and attach the Fuse cover.
7
2.4.
2.4.1.
How to Replace the Lithium Battery
Replacement Procedure
at component side of Top Operation PCB) and then replace it into new one.
1. Remove the Top Operation PCB. (Refer to Disassembly Procedures.) 2. Remove the Lithium battery (Ref. No.
Note: The lithium battery is a critical component. (Type No.: ML-421S/ZT Manufactured by Matsushita Battery Industrial Co.,Ltd.) It must never be subjected to excessive heat or discharge. It must therefore only be fitted in equipment designed specifically for its use. Replacement batteries must be of the same type and manufacture. They must be fitted in the same manner and location as the original battery, with the correct polarity contacts observed. Do not attempt to re-charge the old battery or re-use it for any other purpose. It should be disposed of in waste products destined for burial rather than incineration.
NOTE: Above caution is applicable for a battery pack which is for DMC-TZ5/TZ15 series, as well.
8
3 Service Navigation
3.1. Introduction
This service manual contains technical information, which will allow service personnel's to understand and service this model. Please place orders using the parts list and not the drawing reference numbers. If the circuit is changed or modified, the information will be followed by service manual to be controlled with original service manual.
3.2.
General Description About Lead Free Solder (PbF)
The lead free solder has been used in the mounting process of all electrical components on the printed circuit boards used for this equipment in considering the globally environmental conservation. The normal solder is the alloy of tin (Sn) and lead (Pb). On the other hand, the lead free solder is the alloy mainly consists of tin (Sn), silver (Ag) and Copper (Cu), and the melting point of the lead free solder is higher approx.30 °C (86 °F) more than that of the normal solder. Definition of PCB Lead Free Solder being used
The letter of is printed either foil side or components side on the PCB using the lead free solder. (See right figure)
Service caution for repair work using Lead Free Solder (PbF) · The lead free solder has to be used when repairing the equipment for which the lead free solder is used. (Definition: The letter of is printed on the PCB using the lead free solder.) To put lead free solder, it should be well molten and mixed with the original lead free solder. Remove the remaining lead free solder on the PCB cleanly for soldering of the new IC. Since the melting point of the lead free solder is higher than that of the normal lead solder, it takes the longer time to melt the lead free solder. · Use the soldering iron (more than 70W) equipped with the temperature control after setting the temperature at 350±30 degrees C (662±86 °F). Recommended Lead Free Solder (Service Parts Route.) · The following 3 types of lead free solder are available through the service parts route. RFKZ03D01K-----------(0.3mm 100g Reel) RFKZ06D01K-----------(0.6mm 100g Reel) RFKZ10D01K-----------(1.0mm 100g Reel) Note * Ingredient: tin (Sn) 96.5%, silver (Ag) 3.0%, Copper (Cu) 0.5%, Cobalt (Co) / Germanium (Ge) 0.1 to 0.3% · · · ·
3.3.
Important Notice 1:(Other than U.S.A. and Canadian Market)
1. The service manual does not contain the following information, because of the impossibility of servicing at component level without concerned equipment/facilities. a. Schematic diagram, Block Diagram and PCB layout of MAIN PCB and SUB PCB. b. Parts list for individual parts for MAIN PCB and SUB PCB. When a part replacement is required for repairing MAIN PCB and/or SUB PCB, replace as an assembled parts. (MAIN PCB/ SUB PCB) 2. The following category is/are recycle module part. please send it/them to Central Repair Center. · MAIN PCB (VEP56063A) · SUB PCB (VEP51020A)
9
3.4.
How to Define the Model Suffix (NTSC or PAL model)
There are eight kinds of DMC-TZ5/TZ15, regardless of the colours. · a) DMC-TZ5 (Japan domestic model.) · b) DMC-TZ5P/PC · c) DMC-TZ5EB/EF/EG/E · d) DMC-TZ5EE · e) DMC-TZ15GD · f) DMC-TZ15GT · g) DMC-TZ15GN · h) DMC-TZ5PL/PR/SG, TZ15GC/GK/GJ (DMC-TZ5S is exclusively Japan domestic model.) What is the difference is that the "INITIAL SETTINGS" data which is stored in Flash ROM mounted on Main PCB.
3.4.1.
Defining methods
To define the model suffix to be serviced, refer to the nameplate which is putted on the bottom side of the Unit.
NOTE: After replacing the MAIN PCB, be sure to achieve adjustment. The adjustment instruction is available at "software download" on the "Support Information from NWBG/VDBG-PAVC" web-site in "TSN system", together with Maintenance software.
10
3.4.2.
INITIAL SETTINGS:
When you replace the Main PCB, be sure to perform the initial settings after achieving the adjustment by ordering the following procedure in accordance with model suffix of the unit. 1. IMPORTANT NOTICE: Before proceeding Initial settings, be sure to read the following CAUTIONS.
2. PROCEDURES: · Preparation. Proceed the picture back up from the unit (Refer to above "CAUTION 2") · Step 1. The temporary cancellation of initial setting: Set the REC/PLAY switch to "[ Recording ]". Set the mode dial to "[ Normal picture mode ] (Red camera mark)". While keep pressing [ E. zoom switch ] and "[ UP ] of Cross Key" simultaneously, turn the Power on. · Step 2. The cancellation of initial setting: Set the REC/PLAY switch to "[ Playback ]". Press [ E. zoom switch ] and "[ UP ] of Cross Key" simultaneously, then turn the Power off. · Step 3. Turn the Power on: Set the REC/PLAY switch to "[ Recording ]". Set the mode dial to "[ Normal picture mode ] (Red camera mark)", and then turn the Power on. · Step 4. Display the INITIAL SETTING: While keep pressing [ MENU ] and "[ RIGHT ] of Cross Key" simultaneously, turn the Power off.
11
· Step 5. Set the INITIAL SETTING: (Refer to "CAUTION 1") [Caution for before settings] Once "NONE(JAPAN)" (Area for Japan) or "P" (Area for North America) is selected with "INITIAL SETTINGS", other areas will not displayed even if "INITIAL SETTINGS" menu is displayed again, thus, the area can not be changed. Select the area carefully. Select the area with pressing "[ UP ]/[ DOWN ] of Cross Key", and then press the "[ RIGHT ] of Cross Key".
The only set area is displayed, and then press the "[ RIGHT ] of Cross key" after confirmation. (The unit is powered off automatically.) Confirm the display of "PLEASE SET THE CLOCK" in English when the unit is turned on again. · Step 6. CONFIRMATION: The display shows "PLEASE SET THE CLOCK" when turn the Power on again. When the unit is connected to PC with USB cable, it is detected as removable media. (When the "GT" or "GK" model suffix is selected, the display shows "PLEASE SET THE CLOCK" in Chinese.) 1) As for your reference Default setting condition is given in the following table. · Default setting (After "INITIAL SETTINGS")
MODEL DMC-TZ5S DMC-TZ5P/PC/PL DMC-TZ5EB/EG/E/SG/PR DMC-TZ15GC/GN/GJ DMC-TZ5EF DMC-TZ5EE DMC-TZ15GK DMC-TZ15GT DMC-TZ15GD VIDEO OUTPUT NTSC NTSC PAL PAL PAL PAL NTSC NTSC LANGUAGE Japanese English English French Russian Chinese (simplified) Chinese (traditional) Korean DATE Year/Month/Date Month/Date/Year Date/Month/Year Date/Month/Year Date/Month/Year Year/Month/Date Year/Month/Date Year/Month/Date REMARKS
a) b) c) d) e) f) g) h)
12
4 Specifications
13
14
5 Location of Controls and Components
15
16
6 Service Mode
6.1. Error Code Memory Function
1. General description This unit is equipped with history of error code memory function, and can be memorized 16 error codes in sequence from the latest. When the error is occurred more than 16, the oldest error is overwritten in sequence. The error code is not memorized when the power supply is shut down forcibly (when the unit is powered on by the battery, the battery is pulled out) because the error code is memorized to FLASH ROM when the unit is powered off. 2. How to display The error code can be displayed by the following procedure: Before perform the error code memory function, connect the AC adaptor or insert the battery. (Since this unit has built-in memory, this error code memory function can be performed without inserting SD memory card.) · 1. The temporary cancellation of initial setting: Set the mode dial to "[ Normal picture mode ] (Red camera mark)". While keep pressing [ E. zoom switch ] and "[ UP ] of Cross Key" simultaneously, turn the Power on. · 2. The display of error code: Press [ E. zoom switch ], [MENU] and "[ LEFT ] of Cross Key" simultaneously with the step 1 condition. The display is changed as shown below when the above buttons is pressed simultaneously. Normal display Error code display Operation history display Normal display .....
Example of Error Code Display
· 3. The change of display: The error code can be memorized 16 error codes in sequence, however it is displayed 5 errors on the LCD. Display can be changed by the following procedure: "[ UP ] or [ DOWN ] of Cross Key" : It can be scroll up or down one by one. "[ LEFT ] or [ RIGHT ] of Cross Key" : It can be scroll up or down every 5 error. · 4. How to read the error date: The error date code is displayed "year, month, day, time" in order. (Example: "08030216" 16 hours 2nd MAR. 2008) Error date information is acquired from "Clock setting" setting, it is displayed as "00000000". information when the error occurs. When the clock is not · 5. How to read the error code: One error code is displayed for 8 bit, the contents of error codes is indicated the table as shown below.
17
Attribute LENS
Main item Lens drive
Sub item OIS
C.B./Zoom
Error code Contents (Upper) High 4bits Low 4 bits Check point (Lower) 18*0 1000 PSD (X) error. Hall element (X axis) position detect error in OIS unit. OIS Unit 2000 PSD (Y) error. Hall element (Y axis) position detect error in OIS unit. OIS Unit 3000 GYRO (X) error. Gyro (IC7101: X axis) detect error on Main P.C.B.. IC7101 (Gyro element) or IC6001 (VENUS 4) 4000 GYRO (Y) error. Gyro (IC7101: Y axis) detect error on Main P.C.B.. IC7101 (Gyro element) or IC6001 (VENUS 4) 5000 MREF error (Reference voltage error). IC9101 (LENS drive) or IC6001 (VENUS 4) 6000 Drive voltage (X) error. VENUS 4 AD value error, LENS Unit, LENS flex breaks etc. 7000 Drive voltage (Y) error. VENUS 4 AD value error, LENS Unit, LENS flex breaks etc. 0010 HP Low detect error. (HP ENC. detects always low. (Fully retracted connection.)) Zoom motor, ABS ENC., and/or circuit failure. Zoom deadlock (Exit side). 0020 HP Low detect error. (HP ENC. detects always high. (Exit connection.)) Zoom motor, ABS ENC., and/or circuit failure. Zoom deadlock (Retract side). 0030 Zoom ENC. detect error. (No signal is supplied from Encoder located on Zoom Motor.) 0040 Zoom motor, ABS ENC., and/or circuit failure Zoom deadlock. 0050 0001 0002
Focus
Lens
18*1 18*2
0000 0000 2000 3000 4000 5000 6000 7000 8000 9000 A000 B000 C000 D000 E000 0000 0001 0002
Adj.History
OIS
19*0
HARD
VENUS A/D FLASH ROM (EEPROM Area) SYSTEM
Flash FLASH ROM (EEPROM Area) RTC
28*0 2B*0
2C*0
0001
HP Low detect error (Focus encoder always Low detect error). FP9001-(33) signal line or IC6001 (VENUS 4) HP High detect error (Focus encoder always High detect error). FP9001-(41) signal line or IC6001 (VENUS 4) Power ON time out error. Lens drive system Power OFF time out error. Lens drive system OIS adj. Yaw direction amplitude error (small) OIS adj. Pitch direction amplitude error (small) OIS adj. Yaw direction amplitude error (large) OIS adj. Pitch direction amplitude error (large) OIS adj. MREF error OIS adj. time out error OIS adj. Yaw direction off set error OIS adj. Pitch direction off set error OIS adj. Yaw direction gain error OIS adj. Pitch direction gain error OIS adj. Yaw direction position sensor error OIS adj. Pitch direction position sensor error OIS adj. other error Flash charging error. IC6001-(AC17) signal line or Flash charging circuit EEPROM read error IC6002 (FLASH ROM) EEPROM write error IC6002 (FLASH ROM) SYSTEM IC initialize failure error Communication between IC6001 (VENUS 4) and IC9101 (SYSTEM)
18
Attribute SOFT
Main item CPU
Sub item Reset
Card
Card
Error code High 4bits Low 4 bits 30*0 0001 | 0007 31*0 0001 0002 0004 39*0 38*0 0005 0001 0002 0100 0200 0300 0000 0000 0001 | 0007 0000 0000
Contents (Upper) Check point (Lower) NMI reset Non Mask-able Interrupt (30000001-30000007 are caused by factors) Card logic error SD memory card data line or IC6001 (VENUS 4) Card physical error SD memory card data line or IC6001 (VENUS 4) Write error SD memory card data line or IC6001 (VENUS 4) Format error Camera task finish process time out. Communication between Lens system and IC6001 (VENUS 4) Camera task invalid code error. IC6001 (VENUS 4) File time out error in recording motion image IC6001 (VENUS 4) File data send error in recording motion image IC6001 (VENUS 4) Single or burst recording brake time out. FLASHROM processing early period of camera during movement. Imperfect zoom lens processing. Zoom lens Software error. (0-7bit : command, 8-15bit : status) Though record preprocessing is necessary, it is not called. Though record preprocessing is necessary, it is not completed.
CPU, ASIC hard
Stop
Operation Zoom
Power on Zoom
3B*0 3C*0 35*0
35*1 35*2
About "*" indication in the above table: The third digit from the left is different as follows. - In case of 0 (example: 18001000) When the third digit from the left shows "0", this error occurred under the condition of INITIAL SETTINGS has been completed. It means that this error is occurred basically at user side. - In case of 8 (example: 18801000) When the third digit from the left shows "8", this error occurred under the condition of INITIAL SETTINGS has been released. (Example; Factory assembling-line before unit shipment, Service mode etc.) It means that this error is occurred at service side. · 6. How to returned to Normal Display: Turn the power off and on, to exit from Error code display mode. NOTE: The error code can not be initialized.
19
7 Service Fixture & Tools
7.1. Service Fixture and Tools
The following Service Fixture and tools are used for checking and servicing this unit.
7.2.
When Replacing the Main PCB
After replacing the MAIN PCB, be sure to achieve adjustment. The adjustment instruction is available at "software download" on the "Support Information from NWBG/VDBG-PAVC" web-site in "TSN system", together with Maintenance software.
7.3.
No. 1 2 3 4 5 6 7
Service Position
Parts No. RFKZ0416 RFKZ0363 VFK2024 RFKZ0445 VFK1951 VFK1175 VFK1974 FP9001 (MAIN) FP9002 (MAIN) FP9004 (MAIN) PP9001 (MAIN) FP9801 (SUB) FP9802 (SUB) FP9007 (MAIN) Connection - LENS UNIT - TOP OPERATION UNIT - LCD UNIT - PS9801 (SUB) - CCD UNIT - FP8001 (FLASH) - LCD UNIT Form 41PIN 0.3 FFC 19PIN 0.5 FFC 51PIN 0.3 FFC 100PIN B to B 39PIN 0.3 FFC 16PIN 0.5 FFC 4PIN 0.5 FFC
This Service Position is used for checking and replacing parts. Use the following Extension cables for servicing.
20
7.3.1.
Extension Cable Connections
CAUTION-1. (When servicing FLASH PCB) 1. Be sure to discharge the capacitor on FLASH PCB. Refer to "HOW TO DISCHARGE THE CAPACITOR ON FLASH PCB". The capacitor voltage is not lowered soon even if the AC Cord is unplugged or the battery is removed. 2. Be careful of the high voltage circuit on FLASH PCB. 3. DO NOT allow other parts to touch the high voltage circuit on FLASH PCB.
21
8 Disassembly and Assembly Instructions
8.1. Disassembly Flow Chart
8.2.
PCB Location
22
8.3.
Disassembly Procedure
Fig. Fig.D1 Removal Card Battery 2 Screws (A) 1 Screw (B) 2 Screws (C) FP9004 (Flex) FP9007 (Flex) Rear Case Unit 5 Locking tabs LCD Unit 1 Locking tab Slide Guide Slide Knob FP9001 (Flex) FP9002 (Flex) PP9001 (Connector) Main P.C.B. PCB Spacer Top Operation Unit 2 Locking tabs AF Panel Light FP9902 (Flex) 2 Screws (D) 3 Locking tabs Top Operation P.C.B. NOTE: (When Installing) 1 Screw (E) PCB Plate FP9801 (Flex) FP9802 (Flex) 2 Locking tabs Sub P.C.B. 2 Screws (F) 1 Screw (G) Lens Unit 1 Screw (H) 2 Screws (I) 1 Screw (J) 2 Screws (K) 2 Locking tabs Flash Unit Battery Case Unit Battery Frame Unit 2 Locking tabs Front Grip Front Case 3 Locking tabs Battery Case Unit
8.3.1.
Removal of the Rear Case Unit
No. Item 1 Rear Case Unit
2 3
LCD Unit Main P.C.B. Unit,
Fig.D2 Fig.D3
4 5
Top Operation Unit Top Operation P.C.B.
Fig.D4 Fig.D5
6
Sub P.C.B.
Fig.D6 Fig.D7
7
Lens Unit
Fig.D8
8
Flash Unit, Battery Case Fig.D9 Unit, Battery Frame Unit, Front Grip, Front Case Fig.D10
9
Battery Case Unit
Fig.D11
Fig. D1
23
8.3.2.
Removal of the LCD Unit
8.3.3.
Removal of the Main P.C.B.
Fig. D2
Fig. D3
24
8.3.4.
Removal Top Operation Unit
8.3.5.
Removal of the Top Operation P.C.B.
Fig. D4
Fig. D5
25
8.3.6.
Removal of the Sub P.C.B.
Fig. D6
Fig. D7
8.3.7.
Removal of the Lens Unit
Fig. D8
26
8.3.8.
Removal of the Flash Unit, Battery Case Unit, Battery Frame Unit, Front Grip and Front Case
Fig. D9
Fig. D10
27
8.3.9.
Removal of the Battery Case Unit
8.4.
Disassembly Procedure for the Lens
NOTE: When Disassembling and Assembling for the Lens 1. To minimize the possibility of the CCD being dirt, perform disassemble and/or assemble under the condition of the CCD is being mounted. Disassembling procedures for the CCD unit, refer to item 8.6. 2. Take care that the dust and dirt are not entered into the lens. In case of the dust is putted on the lens, blow off them by airbrush. 3. Do not touch the surface of lens. 4. Use lens cleaning KIT (BK)(VFK1900BK). 5. Apply the grease to the point where is shown to" Grease apply" in the figure.
8.4.1.
1. 2. 3. 4. 5.
Removal of the Zoom Motor Unit and Master Flange Unit
Fig. D11
NOTE: (When Assembling) Be sure to confirm the following points when assembling. · The Screw is tightened enough. · Assembling conditions are fine. (No distortion, no illegalspace.) · No dust and/or dirt on every Lens surfaces. · LCD image is fine. (No dust and dirt on it, and no gradient images.)
Unsolder (16 points). Remove the libs (4 points). Unscrew the 6 screws (A). Remove the zoom motor unit. Remove the master flange unit.
28
8.4.2.
Removal of the Direct Frame, Both Side Cam, 1st Lens Frame/2nd Lens Frame/3rd Lens Frame, Penetration Cam and Drive Frame
8.4.3.
Removal of the Direct Frame, Both Side Cam and 1st Lens Frame/2nd Lens Frame/3rd Lens Frame
· Push the penetration cam to the indicated by arrow from lens side, and then remove the unit of direct frame, both side cam, 1st lens frame/2nd lens frame/3rd lens frame, penetration cam and drive frame from the fixed frame unit.
1. Turn the drive frame, and then Align the groove of drive frame and pin of 1st lens frame.
2. Push the 1st lens frame to the indicated by arrow from lens side, and then remove the unit of direct frame, both side cam and 1st lens frame/2nd lens frame/3rd lens frame from the penetration cam and drive frame.
29
8.4.4.
Removal of the Direct Frame, Both Side Cam and 2nd Lens Frame/3nd Lens Frame
8.4.5.
Removal of the 3rd Lens Frame and 2nd Lens Frame
· Turn to the indicated by arrow(1) while picking the pin, and then remove the unit of direct frame, both side cam and 2nd lens frame/3rd lens frame from the 1st lens frame.
1. Turn the direct frame, and then Align the groove of direct frame and groove of both side cam. 2. Remove the 3rd lens frame and 2nd lens frame from the direct frame, both side cam.
30
8.4.6.
Removal of the Direct Frame
8.5.
8.5.1.
Assembly Procedure for Lens
Phase alignment of the Penetration Cam and Drive Frame
31
8.5.2.
Phase alignment of the Direct Frame and Both Side Cam
8.5.3.
Assembly for the 2nd Lens Frame and 3nd Lens Frame
32
8.5.4.
Assembly for the Direct Frame, Both Side Cam and 2nd Lens Frame/3nd Lens Frame
8.5.5.
Assembly for the Direct Frame, Both Side Cam and 1st Lens Frame/ 2nd Lens Frame/3rd Lens Frame
33
8.5.6.
Assembly for the Direct Frame, Both Side Cam and 1st Lens Frame/ 2nd Lens Frame/3rd Lens Frame, Penetration Cam and Drive Frame
8.5.7.
Assembly for the Zoom Motor Unit and Master Flange Unit
34
8.6.
Removal of the CCD Unit
To prevent the CCD unit from catching the dust and dirt, do not remove the CCD unit except for replacing.
35
8.7.
Removal of the Zoom Motor Unit
8.8.
Removal of the Focus Motor Unit
36
8.9.
The Applyment Method
of
Grease
The grease apply point of lens unit are as follows. Apply grease additionally in the specified position if necessary. When the grease is applied, use a toothpick and apply thinly. · Focus motor nut moving part - Grease: RFKZ0472 - Amount of apply: 3 - 5 mg · 4th lens frame positioning pole, guide pole - Grease: RFKZ0472 - Amount of apply: 0.15 - 0.35 mg
37
9 Measurements and Adjustments
9.1. Matrix Chart for Replaced Part and Necessary Adjustment
The relation between Replaced part and Necessary Adjustment is shown in the following table. When concerned part is replaced, be sure to achieve the necessary adjustment(s). As for Adjustment condition/procedure, consult the "Adjustment Manual" which is available in Adjustment software. The Adjustment software is available at "TSN Website", therefore, access to "TSN Website" at "Support Information from NWBG/ VDBG-PAVC". NOTE: After adjustments have been terminated, make sure to achieve "INITIAL SETTINGS".
Replaced Part Flash-ROM Lens Part (IC6002) (Excluding CCD) O O O O O O O O O O
Adjustment Item
Main P.C.B.
VENUS (IC6001) O O O O O
CCD Unit
Camera Section
OIS hall element adjustment (OIS) Back focus adjustment (BF) Shutter adjustment (SHT) ISO sensitivity adjustment (ISO) AWB adjustment High brightness coloration inspection (WBL) CCD white scratch compensation (WKI) CCD black scratch compensation (BKI)
O O O O O
O*1 O O O
O O
O O
O O
-
O*1 O*1
*1 This adjustment is necessary, not only replacing CCD unit but also removing it from the lens unit. NOTE: *There is no LCD adjustment in this model.
38
10 Maintenance
10.1. Cleaning Lens, Viewfinder and LCD Panel
Do not touch the surface of lens, Viewfinder and LCD Panel with your hand. When cleaning the lens, use air-Blower to blow off the dust. When cleaning the LCD Panel, dampen the lens cleaning paper with lens cleaner, and the gently wipe the their surface. Note: The Lens Cleaning KIT ; VFK1900BK(Only supplied as 10 set/Box) is available as Service Aid.
39
DSC0803021CE
S1. About Indication of The Schematic Diagram
S1.1. Important Safety Notice
COMPONENTS IDENTIFIED WITH THE MARK HAVE THE SPECIAL CHARACTERISTICS FOR SAFETY. WHEN REPLACING ANY OF THESE COMPONENTS USE ONLY THE SAME TYPE. 1.Although reference number of the parts is indicated on the P.C.B. drawing and/or schematic diagrams, it is NOT mounted on the P.C.B. when it is displayed with "$" mark. 2.It is only the "Test Round" and no terminal (Pin) is available on the P.C.B. when the TP (Test Point) indicated as " " mark. 3.The voltage being indicated on the schematic diagram is measured in "Standard-Playback" mode when there is no specify mode is mentioned. 4.Although the voltage and waveform available on here is measured with standard frame, it may be differ from actual measurement due to modification of circuit and so on. 5.The voltage being indicated here may be include observational-error (deviation) due to internal-resistance and/or reactance of equipment. Therefore, handle the value indicated on here as reference. 6.Use the parts number indicated on the Replacement Parts List . 7.Indication on Schematic diagrams:
Circuit name being connected.
Service Manual Diagrams and Replacement Parts List
Digital Camera
Model No. DMC-TZ5P DMC-TZ5PC DMC-TZ5PL DMC-TZ5PR DMC-TZ5EB DMC-TZ5EE DMC-TZ5EF DMC-TZ5EG DMC-TZ5E DMC-TZ5SG DMC-TZ15GC DMC-TZ15GD DMC-TZ15GK DMC-TZ15GN DMC-TZ15GT DMC-TZ15GJ
Vol. 1 Colour (S)...........Silver Type (except PR/GD) (K)...........Black Type (A)...........Blue Type (only P/PC/PL/PR/EE/EG/E) (TA).........Dark Brown Type (only EF/EG/E) (T)...........Brown Type (only SG/GC/GK/GJ)
OFTR
FEP
This signal is connected to the FEP schematic diagram.
Name of Signal
Table of contents
S1. About Indication of The Schematic Diagram ............................ S-1 S1.1. Important Safety Notice......................................................... S-1 S2. Voltage Chart ........................................................................... S-2 S2.1. Flash P.C.B. .......................................................................... S-2 S3. Block Diagram .......................................................................... S-3 S3.1. Overall Block Diagram .......................................................... S-3 S4. Schematic Diagram .................................................................. S-4 S4.1. Interconnection Diagram ....................................................... S-4 S4.2. Flash Schematic Diagram ..................................................... S-5 S4.3. Top Operation Schematic Diagram ....................................... S-6 S4.4. CCD Flex Schematic Diagram .............................................. S-7 S4.5. Lens Flex Schematic Diagram .............................................. S-8 S5. Print Circuit Board .................................................................... S-9 S5.1. Flash P.C.B. .......................................................................... S-9 S5.2. Top Operation P.C.B. ........................................................... S-10 S5.3. CCD Flex P.C.B................................................................... S-11 S5.4. Lens Flex P.C.B................................................................... S-12 S6. Replacement Parts List .......................................................... S-13 S7. Exploded View ....................................................................... S-17 S7.1. Frame and Casing Section.................................................. S-17 S7.2. Packing Parts and Accessories Section .............................. S-18
S-1
S2. Voltage Chart
Note) Indicated voltage values are the standard values for the unit measured by the DC electronic circuit tester (high-impedance) with the chassis taken as standard. Therefore, there may exist some errors in the voltage values, depending on the internal impedance of the DC circuit tester.
S2.1. Flash P.C.B.
REF No. IC8001 IC8001 IC8001 IC8001 IC8001 Q8009 Q8009 Q8009 Q8009 Q8009 Q8009 PIN No. 1 2 3 4 5 1 2 3 4 5 6 POWER ON 0 4.9 0 0 5.1 5.1 0 0 5.1 5.1
S-2
S3. Block Diagram
S3.1. Overall Block Diagram
(28mm ~ 280mm) IC3101 CCD
1/2.33" 10 MEGA PIX
IC6002 IC3001 PRE PROCESS
CDS,AGC, A/D,TG, CCD DRIVER
FLASH ROM /512Mbit SDRAM/256Mbit
ZOOM
IRIS
SHUTTER
OIS UNIT
FOCUS
SD CARD
IC9101 MOTOR DRIVE, OIS DRIVE& PRE PROCESS
IC2102 HD VIDEO OUT
HD VIDEO
IC9101 AUDIO AMP
MICROPHONE AMP SPEAKER CONTROL
MICROPHONE
SPEAKER
IC7101 GYRO SENSOR X/Y
IC6001 VENUS4 FLASH
CAMERA PROCESS J-PEG COMP/EX PANDS MEDIA I/F USB I/F MAIN MICROPROCESSOR OIS CONTROL LENS DRIVE LCD DRIVE
IC9001 VIDEO OUT
DIGITAL/ AV OUT TERMINAL
REAR OPERATION UNIT
IC9101 SYSTEM IC
COLOUR LCD PANEL
3.0" PANEL 460K PIX
(Type of LCD Driver inclusion) X9101 (32.768kHz)
TOP OPERATION UNIT
DC IN TERMINAL
(POWER SUPPLY) BATTERY
IC1001 POWER
DMC-TZ5/TZ15 OVERALL BLOCK DIAGRAM
S-3
S4. Schematic Diagram
S4.1. Interconnection Diagram
TOP OPERATION P.C.B. (COMPONENT SIDE)
: (FOIL SIDE) SPEAKER
BATTERY
FLASH P.C.B. (FOIL SIDE)
: (COMPONENT SIDE)
FP9901 LI BATT+ NC POWER ON L NC E ZOOM TELE WIDE SHUTTER 0 SHUTTER 1 D GND D GND D GND MODE DTAL A GND MIC IN A GND SPSP+ AF LED K AF LED A (D3V) ET9902
TL8902
TL8901
ET9901
TL8903
1 2 3 4
FP9902 MIC GND MIC GND MIC IN MIC IN
FP8001 UNREG UNREG UNREG NC BATBATBATNC STROBE TRG A GND STB PWM OUT STB CHG LV 5V BAT THERMO UNREG GND UNREG GND
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19
MICROPHONE
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16
MAIN P.C.B. (FOIL SIDE)
: (COMPONENT SIDE)
FP9004 NC VCAMFH VCSH SI XRST TEST OUT15V GND C50LCF1P C50LCF2P GND VDD C65LCFP C50LCFP OUT50LV DE XHD DC0 DC2 DC4 DC6 DY0 DY2 DY4 DY6 GND 1 3 5 7 9 11 13 15 17 19 21 23 25 27 29 31 33 35 37 39 41 43 45 47 49 51
FP9002
FP9802
2 4 6 8 10 12 14 16 18 20 22 24 26 28 30 32 34 36 38 40 42 44 46 48 50
NC VCAMPL XCS XSCK SO VREF VGM C50LCF1N C50LCF2N OUT50V VDD C65LCFN OUT65P C50LCFN VDDIO XVD DCLK DC1 DC3 DC5 DC7 DY1 DY3 DY5 DY7
LCD UNIT
CCD UNIT
LENS UNIT
1 3 5 7 9 11 13 15 17 19 21 23 25 27 29 31 33 35 37 39
FP9801 CON CHK CCD THERMO SUBSW2 SUBSW1 SUB MSUBSW MSUB V9R V9L V11R V11L V12 V11 V7 V10 V9 V8 V7S V7A V11A V7B V11B V6 V5AV5B V1 V4 V3AV3B V3 V2 V1A V5A V1B V5B VL CCD GND VH CCD GND CCD OUT CCD GND CCD GND R HL H1 H2 CCD GND CON CHK
2 4 6 8 10 12 14 16 18 20 22 24 26 28 30 32 34 36 38
SUB P.C.B. (FOIL SIDE)
51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100
PS9801 POWER CTL SW UNREG UNREG ACADP IN STB PWM OUT BAT THERMO STB CHG LV HD CABLE DET A GND CABLE DET G VIDEO A GND G VIDEO PB G LINE OUT G VIDEO PR A GND A GND A GND HD DRV MUTE G SDTV OUT A GND A GND A GND A GND HD3V ON H A GND LCD BLT A GND PW BL MINUS BLT PWM PW A3R1V USB CAB IN PW A3R1V PW BL PLUS PW D3V PW D1R8V PW D3V PW D1R8V D GND PW 5V G USBPW 5V G USB+ PW D1R2V D GND PW D1R2V D GND PW AF2R4V SCACLK PW AF2R4V D GND SCACD SCADAT2 SCAWP SCADAT0 D GND SCACMD SCADAT3 D GND SCADAT1 N.C. D GND D GND N.C. D GND N.C. D GND N.C. CCD1 CCD0 CCD2 CCD3 CCD4 CCD5 CCD6 CCD7 CCD8 CCD9 CCD10 CCD11 CCDVD S AFE SCK CCDHD S AFE SDATA D GND S AFE CS CLK45 FCK MSUBSW D GND D GND CCD POWER SE CCD THERMO D GND D GND D GND D GND FRAME GND FRAME GND FRAME GND FRAME GND
BAT+ BAT+ BAT+ NC BATBATBATNC STROBE TRG A GND STB PWM OUT STB CHG LV 5V BAT THERMO UNREG GND UNREG GND
50 49 48 47 46 45 44 43 42 41 40 39 38 37 36 35 34 33 32 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1
1 LI BATT+ 2 NC POWER ON L 3 4 NC 5 E ZOOM 6 TELE WIDE 7 SHUTTER 0 8 SHUTTER 1 9 D GND 10 D GND 11 D GND 12 MODE DTAL A GND 13 14 MIC IN 15 A GND 16 SPSP+ 17 18 AF LED K AF LED A (D3V) 19 PP9001 50 POWER CTL SW UNREG 49 ACADP IN UNREG 48 BAT THERMO STB PWM OUT 47 HD CABLE DET STB CHG LV 46 CABLE DET A GND G VIDEO 45 A GND 44 G LINE OUT G VIDEO PB 43 A GND G VIDEO PR 42 A GND A GND 41 G SDTV OUT HD DRV MUTE 40 A GND A GND 39 A GND A GND 38 A GND HD3V ON H 37 A GND LCD BLT 36 BLT PWM PW BL MINUS PW A3R1V 35 USB CAB IN 34 PW BL PLUS PW A3R1V 33 PW D1R8V PW D3V 32 PW D1R8V PW D3V 31 PW 5V D GND 30 PW 5V G USB29 PW D1R2V G USB+ 28 PW D1R2V D GND 27 PW AF2R4V D GND 26 PW AF2R4V SCACLK 25 SCACD D GND SCADAT2 24 SCAWP 23 D GND SCADAT0 SCACMD 22 SCADAT3 D GND 21 SCADAT1 20 D GND D GND 19 D GND D GND 18 D GND D GND 17 D GND D GND 16 CCD1 CCD0 CCD2 15 CCD3 14 CCD5 CCD4 13 CCD7 CCD6 12 CCD9 CCD8 11 CCD11 CCD10 10 S AFE SCK CCDVD 9 S AFE SDATA CCDHD 8 S AFE CS D GND 7 MSUBSW CLK45 FCK 6 D GND D GND 5 CCD THERMO CCD POWER SE 4 D GND D GND D GND 3 D GND 2 FRAME GND FRAME GND 1 FRAME GND FRAME GND
16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1
51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100
FP9007 BL PLUS BL MINUS BL RANK D GND
1 2 3 4
2 4 6 8 10 12 14 16 18 20 22 24 26 28 30 32 34 36 38 40
FMAN FMBP FMAP FZHP LED K ESD GND SHUT2 SHUT1 IRIS2 IRIS1 YHOXV+ XVYDRXDRYHO+ ZENC1 LED K ZENC1 VCC ZM+ ZMZENC2 LED K
FP9001 FMBN FMBP FMAP FZHP VCC FZHP SHUT2 SHUT1 IRIS2 IRIS1 YV+ XHO+ XHOYDR+ XDR+ YVESD GND ZENC1 ZM+ ZMZENC2 VCC ZENC2
1 3 5 7 9 11 13 15 17 19 21 23 25 27 29 31 33 35 37 39 41
DMC-TZ5/TZ15 INTERCONNECTION SCHEMATIC DIAGRAM
S-4
S4.2. Flash Schematic Diagram
G
1.25A 32V
CAUTION: FOR CONTINUED PROTECTION AGAINST FIRE HAZARD, REPLACE ONLY WITH THE SAME TYPE 1.25A 32V FUSE. ATTENTION: POUR UNE PROTECTION CONTINUE LES RISQUES D' INCENDIE N' UTILISERQUE DES FUSIBLE DE MÉME TYPE 1.25A 32V.
1.5A 32V
CAUTION: FOR CONTINUED PROTECTION AGAINST FIRE HAZARD, REPLACE ONLY WITH THE SAME TYPE 1.5A 32V FUSE. ATTENTION: POUR UNE PROTECTION CONTINUE LES RISQUES D' INCENDIE N' UTILISERQUE DES FUSIBLE DE MÉME TYPE 1.5A 32V.
F
1.25A 32V 1.5A 32V
E
D
C
B
A
DMC-TZ5/TZ15 Flash Schematic Diagram
1
2
3
4
5
6
7
8
9
10
S-5
S4.3. Top Operation Schematic Diagram
G
F
E
D
C
B
A
DMC-TZ5/TZ15 Top Operation Schematic Diagram
1
2
3
4
5
6
7
8
9
10
S-6
S4.4. CCD Flex Schematic Diagram
G
F
E
D
C
B
A
DMC-TZ5/TZ15 CCD Flex Schematic Diagram
1
2
3
4
5
6
7
8
9
10
S-7
S4.5. Lens Flex Schematic Diagram
POSITIVE VOLTAGE LINE
G
FMBN FMAN FMBP FMBP FMAP FMAP 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 E1 E2 E3 F1 D1 D2 D3 D4 D5 D6 D7 D8 D9 D10 D11 D12 C4 C3 C1 B1 B2 B3 A4 A1 A2 A3
COIL
COIL
STEPPING MOTOR
A FOCUS MOTOR UNIT
F
FZHP_VCC FZHP_LED_K FZHP ESD_GND SHUT2 SHUT2 SHUT1
PHOTO SENSOR
B FOCUS ENCODER
C2
E
SHUT1 IRIS2 IRIS2 IRIS1
DC SOLENOID (SHUTTER) C SHUTTER UNIT DC SOLENOID (IRIS)
TO MAIN (MAIN CN) CIRCUIT (FP9001)
IRIS1 YV+ YH0XH0+
D
XV+ XH0XVYDR+ YDRXDR+ XDR-
HALL SENSOR (X)
DRIVE COIL (Y ) DRIVE COIL (X) HALL SENSOR (Y )
D OIS
C
YVYH0+ ESD_GND
ZENC1_LED_K 32 ZENC1 ZENC1_VCC ZM+ ZM+ 33 34 35 36 37 38 39
PHOTO SENSOR
E FOCUS ENCODER
B
ZMZMZENC2_VCC
F2
DC MOTOR
D ZOOM MOTOR UNIT
G1 G2 G3
ZENC2_LED_K 40 ZENC2 41
PHOTO SENSOR
G ZOOM ENCODER 2
A
DMC-TZ5/TZ15 LENS FLEX SCHEMATIC DIAGRAM
1
2
3
4
5
6
S-8
S5. Print Circuit Board
S5.1. Flash P.C.B.
G
F
E
(Component Side)
D
C
B
(Foil Side)
A
DMC-TZ5/TZ15 Flash P.C.B.
1
2
3
4
5
6
7
8
9
10
S-9
S5.2. Top Operation P.C.B.
G
F
E
D
(Component Side)
C
B
A
(Foil Side)
DMC-TZ5/TZ15 Top Operation P.C.B.
1
2
3
4
5
6
7
8
9
10
S-10
S5.3. CCD Flex P.C.B.
G
F
E
D
(Component Side)
C
B
A
(Foil Side)
DMC-TZ5/TZ15 CCD Flex P.C.B.
1
2
3
4
5
6
7
8
9
10
S-11
S5.4. Lens Flex P.C.B.
F
B FOCUS ENCODER B3 B2
B1
E
A FOCUS MOTOR UNIT A1 A2
A4 C1 C2
A3
D
C SHUTTER UNIT
C3 C4
E D OIS
ZOOM ENCODER1
Pin1
C
D6
D7
D5
D4
D8
D3
D2
D1
D9
D10 D11
D12
E1
E2
E3
F1 F ZOOM MOTOR UNIT Pin41
G3
G2
G1
F2
B
G ZOOM ENCODER2
A
DMC-TZ5/TZ15 LENS FLEX P. C. B.
1
2
3
4
5
6
7
8
9
S-12
S6. Replacement Parts List
Note: 1.* Be sure to make your orders of replacement parts according to this list. 2. IMPORTANT SAFETY NOTICE Components identified with the mark have the special characteristics for safety. When replacing any of these components, use only the same type. 3. Unless otherwise specified, All resistors are in OHMS, K=1,000 OHMS. All capacitors are in MICRO-FARADS (uf), P=uuF. 4. The marking (RTL) indicates the retention time is limited for this item. After the discontinuation of this assembly in production, it will no longer be available. 5. Supply of CD-ROM, in accordance with license protection, is allowable as replacement parts only for customers who accidentally damaged or lost their own.
E.S.D. standards for Electrostatically Sensitive Devices, refer to PREVENTION OF ELECTROSTATIC DISCHARGE (ESD) TO ELECTROSTATICALLY SENSITIVE (ES) DEVICES section. Definition of Parts supplier: 1. Parts marked with [MBI] in the remarks column are supplied from Matsushita Battery Industrial Co., Ltd.
S-13
DMC-TZ5P/PC/PL/PR/EB/EE/EF/EG/E/SG, TZ15GC/GD/GK/GN/GT/GJ vol.1
Ref.No.
## ## ## ## ##
Part No.
VEP51020A VEP56063A VEP59052A VEP58055A VEK0L97
Part Name & Description
SUB P.C.B MAIN P.C.B TOP OPERATION P.C.B FLASH P.C.B CCD UNIT
Pcs
1 (RTL) E.S.D 1 (RTL) E.S.D
Remarks
Ref.No.
T8002
Part No.
Part Name & Description
Pcs
1
Remarks
G5F1A0000024 TRANSFORMER
## 1 (RTL) E.S.D 1 (RTL) E.S.D 1 E.S.D. C3101 C3103 Q3101 R3101 R3102 R3107 R3108 TH3101 ET9901 ET9902 FP9901 FP9902 LB9911 LB9912 R9901 R9902 R9903 R9904 R9905 R9907 R9908 R9909 R9911 R9912 R9913 S9901 S9902 S9903 S9904 ZB9901 K4AC01D00001 EARTH SPRING K4AC01D00001 EARTH SPRING K1MN19BA0209 CONNECTOR K1MN04BA0208 CONNECTOR J0JCC0000317 J0JCC0000317 ERJ2GEJ152 ERJ2GEJ242 ERJ2GEJ362 ERJ2GEJ562 ERJ2GEJ123 ERJ2GEJ332 ERJ2RHD682X ERJ2GEJ223 ERJ3GEYJ100 ERJ3GEYJ100 ERJ6GEYJ512 K0MZ26000001 K0D112B00145 EVQPQ6B55 K0G166A00004 K3ZZ00200042 FILTER FILTER M.RESISTOR CH 1/16W M.RESISTOR CH 1/16W M.RESISTOR CH 1/16W M.RESISTOR CH 1/16W M.RESISTOR CH 1/16W M.RESISTOR CH 1/16W M.RESISTOR CH 1/16W M.RESISTOR CH 1/16W M.RESISTOR CH 1/10W M.RESISTOR CH 1/10W M.RESISTOR CH 1/10W SWITCH SWITCH SWITCH ROTARY SWITCH BATTERY HOLDER 1.5K 2.4K 3.6K 5.6K 12K 3.3K 6.8K 22K 10 10 5.1K 19P 4P 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
VEK0L97
CCD UNIT 1 1
E.S.D.
ECJ1VB1C105K C.CAPACITOR CH 16V 1U F1H1A225A051 C.CAPACITOR CH 10V 2.2U UP05C8B00L ERJ2GEJ470 ERJ2GEJ182 ERJ2GEJ821 ERJ2RKD330 TRANSISTOR M.RESISTOR CH 1/16W 47 M.RESISTOR CH 1/16W 1.8K M.RESISTOR CH 1/16W 820 M.RESISTOR CH 1/16W 33
1 E.S.D. 1 1 1 1 1
## D9901
VEP59052A
TOP OPERATION P.C.B
(RTL) E.S.D 1 E.S.D.
B3ADB0000120 LED
D4CC11030026 THERMISTER
## C8001 C8004 C8006 C8007 C8009 D8002 F8001 F8002 FP8001 IC8001 Q8001 Q8009 R8002 R8003 R8004 R8006 R8013 R8021 R8032 R8033 T8001
VEP58055A ECJ1VB0J105K F1K2J102A010 F1K2J333A031 F1G1A1040006 F1J1A106A024
FLASH P.C.B C.CAPACITOR CH 6.3V 1U C.CAPACITOR 630V 1000P C.CAPACITOR 630V 0.033U C.CAPACITOR CH 10V 0.1U C.CAPACITOR CH 10V 10U 1 1 1 1 1
(RTL) E.S.D
B0EDAT000002 DIODE ERBSE1R25U ERBSE1R50U FUSE 32V 1.25A FUSE 32V 1.5A 16P
1 E.S.D. 1 1 1 1 E.S.D. 1 E.S.D. 1 E.S.D. 100K 82 0 1M 15K 15K 1M 1M 1 1 1 1 1 1 1 1 1
K1MN16BA0209 CONNECTOR C0ZBZ0000914 IC B1JBLP000016 TRANSISTOR B1DFCG000020 TRANSISTOR ERJ3GEYJ104 ERJ3GEYJ820 D0YAR0000007 ERJ8GEYJ105V ERJ2RHD153X ERJ2GEJ153 ERJ6RED105 ERJ6RED105
M.RESISTOR CH 1/10W M.RESISTOR CH 1/10W M.RESISTOR CH 1/16W M.RESISTOR CH 1/8W M.RESISTOR CH 1/16W M.RESISTOR CH 1/16W M.RESISTOR CH 1/16W M.RESISTOR CH 1/16W
G5D1A0000061 TRANSFORMER
S-14
DMC-TZ5P/PC/PL/PR/EB/EE/EF/EG/E/SG, TZ15GC/GD/GK/GN/GT/GJ vol.1
Ref.No.
1 2 3 4 5 7 8 9 11 11 13 14 15 16 17 18 19 20 23 23 23 23 23 23-1 23-2 23-2 23-2 23-2 23-2 23-3 23-4 23-5 23-5 23-5 23-5 23-5 24 24 24 24 24 24-1 25 26 27 28 29 29 29 29 29 30 31 33 35 36 37 38 40 41
Part No.
VEP51020A VEP56063A L0AA01A00032 ML421S/ZT VMB4169 VGU0B04 VEP59052A VML3972 VYK2S33 VYK2S34 VEK0L84 VGQ9761 VMB4024 VWJ2036 VEP58055A VGQ9765 F2A2F9500003 VGL1274 VYQ4283 VYQ4287 VYQ4288 VYQ4289 VYQ4290 VGK3414 VKF4299 VKF4300 VKF4301 VKF4302 VKF4334 VMS7822 VMS7893 VYF3178 VYF3182 VYF3183 VYF3184 VYF3185 VYK2N05 VYK2N09 VYK2N07 VYK2N11 VYK2N13 VGQ9758 VYK2M54 VGU0C33 VGK3409 VGK3412 VYK2R55 VYK2R56 VYK2R57 VYK2R58 VYK2R59 VGQ9317 VGQ9760 VGQ9162 VMC2056 VGQ9162 VWJ2035 VGL1230 VEK0M49 VGQ9909
Part Name & Description
SUB P.C.B MAIN P.C.B SPEAKER BUTTON BATTERY EARTH SPRING OIS BUTTON TOP OPERATION P.C.B SLIDE KNOB TOP ORNAMENT U TOP ORNAMENT U FLASH U CONDENSER COVER BATTERY SPRING FPC FLASH P.C.B SLIDE GUIDE E.CAPACITOR CH 300V 95UF AF PANEL LIGHT FRAME ASSY FRAME ASSY FRAME ASSY FRAME ASSY FRAME ASSY STRAP HOLDER JACK DOOR JACK DOOR JACK DOOR JACK DOOR JACK DOOR BATTERY DOOR SHAFT JACK DOOR SHAFT BATTERY DOOR ASSY BATTERY DOOR ASSY BATTERY DOOR ASSY BATTERY DOOR ASSY BATTERY DOOR ASSY FRONT CASE ASSY FRONT CASE ASSY FRONT CASE ASSY FRONT CASE ASSY FRONT CASE ASSY LENS ORNAMENT LCD ASSY CURSOR BUTTON FRONT GRIP GRIP FIX REAR CASE ASSY REAR CASE ASSY REAR CASE ASSY REAR CASE ASSY REAR CASE ASSY TRIPOD PCB SPECER CURSOL TAPE PCB PLATE CURSOL TAPE FPC REAR PANEL LIGHT HEAT SINK SHEET U LCD SHEET
Pcs
1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 (RTL) E.S.D (RTL) E.S.D
Remarks
Ref.No.
201 202 203 204 205 207 208 210 211 214 215 216 217 218 B1 B1 B2 B2 B3 B3 B4 B5 B6 B7 B8 B9 B9 B10 B10 B11 B11 B12 B12 B13 B13 B14 B14 B15 B15 B16 B17 B18 B19 B20 B201 B202 B203 B207 B208 B209 B210 B211 B212 B213 B214
Part No.
VDL2073 VEK0L97 VMX3650-B L6DABCGD0002 B3NAA0000132 VDW1412 VXP2912 VXP2746 VXP2918 VXQ1576 L6HA86ND0002 VXW0934 VXP2830 VEK0L98 VHD1693 VHD1853 VHD1693 VHD1853 VHD1693 VHD1853 VHD1652 VHD1652 VHD1921 VHD1921 VHD1926 VHD1954 VHD1956 VHD1954 VHD1956 VHD1954 VHD1956 VHD1954 VHD1956 VHD1957 VHD1958 VHD1957 VHD1958 VHD1957 VHD1958 VHD1803 VHD1924 VHD1924 XQN16+BJ3FN VHD1652 VHD1871 VHD1871 VHD1871 VHD1871 XQN14+CJ4FN XQN14+CJ4FN XQN14+CJ4FN XQN14+CJ4FN XQN14+CJ4FN XQN14+CJ4FN XQN14+CJ4FN
Part Name & Description
OPTICAL FILTER CCD UNIT CCD CUSHION RUBBER ZOOM MOTOR UNIT PHOTO COUPLER 2ND/3RD DIRECT FRAME 1ST LENS FRAME UNIT 2ND LENS FRAME UNIT 3RD LENS FRAME UNIT MASTER FRANGE UNIT FOCUS MOTOR UNIT LENS UNIT FIX CAM FRAME UNIT LENS FPC SCREW SCREW SCREW SCREW SCREW SCREW SCREW SCREW SCREW SCREW SCREW SCREW SCREW SCREW SCREW SCREW SCREW SCREW SCREW SCREW SCREW SCREW SCREW SCREW SCREW SCREW SCREW SCREW SCREW SCREW SCREW SCREW SCREW SCREW SCREW SCREW SCREW SCREW SCREW SCREW SCREW
Pcs
1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 (-S)(-T) (-K)(-A)(-TA) (-S)(-T) (-K)(-A)(-TA) (-S)(-T) (-K)(-A)(-TA)
Remarks
(MBI) (B9901)
(RTL) E.S.D (TZ5) (TZ15)
(RTL) E.S.D (C8003) (-S) (-K) (-A) (-T) (-TA) (-S) (-K) (-A) (-T) (-TA)
(-S) (-K) (-A) (-T) (-TA) (-S) (-K) (-A) (-T) (-TA)
(-S)(-T) (-K)(-A)(-TA) (-S)(-T) (-K)(-A)(-TA) (-S)(-T) (-K)(-A)(-TA) (-S)(-T) (-K)(-A)(-TA) (-S)(-T) (-K)(-A)(-TA) (-S)(-T) (-K)(-A)(-TA) (-S)(-T) (-K)(-A)(-TA)
(-S) (-K) (-A) (-T) (-TA)
S-15
DMC-TZ5P/PC/PL/PR/EB/EE/EF/EG/E/SG, TZ15GC/GD/GK/GN/GT/GJ vol.1
Ref.No.
301 302 302 302 302 302 302 302 302 303 303 304 304 304
Part No.
Part Name & Description
Pcs
Remarks
Ref.No.
313
Part No.
VQT1P89 VQT1P94
Part Name & Description
SIMPLIFIED O/I (HUNGARIAN/FINNISH) SIMPLIFIED O/I (ENGLISH/ CHINESE(TRADITIONAL)) SIMPLIFIED O/I (ARABIC/PERSIAN) INSTRUCTION BOOK (KOREAN) INSTRUCTION BOOK (CHINESE(SIMPLIFIED)) INSTRUCTION BOOK (ENGLISH) INSTRUCTION BOOK (CHINESE(TRADITIONAL)) INSTRUCTION BOOK (THAI) O/I SOFTWARE (ENGLISH/CANADIAN FRENCH) O/I SOFTWARE (ENGLISH/SPANISH/ PORTUGUESE) O/I SOFTWARE (GERMAN/ITALIAN/FRENCH/ DUTCH/SPANISH/ PORTUGUESE) O/I SOFTWARE (ENGLISH) O/I SOFTWARE (RUSSIAN/UKRAINIAN) O/I SOFTWARE (FRENCH) O/I SOFTWARE (FINNISH/SWEDISH/DANISH/ POLISH/CZECH/HUNGARIAN) O/I SOFTWARE (ENGLISH/ CHINESE(TRADITIONAL)/ ARABIC/PERSIAN) O/I SOFTWARE (KOREAN) O/I SOFTWARE (CHINESE(SIMPLIFIED)) O/I SOFTWARE (CHINESE(TRADITIONAL)) O/I SOFTWARE (THAI) BATTERY CARRYING CASE U BATTERY CARRYING CASE U PAD PAD
Pcs
1 TZ5E 1 TZ5SG, TZ15GC 1 TZ5SG, TZ15GC 1 TZ15GD 1 TZ15GK 1 TZ15GN 1 TZ15GT 1 TZ15GJ 1 TZ5P,PC 1 TZ5PL
Remarks
VPF1137 CAMERA BAG K2CJ2DA00006 AC CORD W/PLUG K2CT3CA00004 AC CORD W/PLUG K2CQ2CA00006 AC CORD W/PLUG K2CR2CA00003 K2CA2CA00020 K2CJ2DA00008 K2CA2CA00027 K2CP2YY00001 ----------------------DE-A45BA DE-A46DA DE-A46AA DE-A46BA DE-A46CA K1HA08CD0019 K1HA08CD0020 VFC4297 VFF0400-S VFF0401-S VPK3446 VPK3517 VPK3525 VPK3447 VPK3518 VPK3526 VPK3560 VPK3565 VPK3448 VPK3519 VPK3523 VPK3449 VPK3520 VPK3524 VPN6659 VPF1294 VFF0413 VQT1P79 VQT1P80 VQT1P81 VQT1P82 VQT1P83 VQT1P86 VQT1P91 VQT1P92 VQT1P93 VQT1P90 VQT1P84 VQT1P85 VQT1P87 VQT1P88 AC CORD W/PLUG AC CORD W/PLUG AC CORD W/PLUG AC CORD W/PLUG AC CORD W/PLUG BATTERY PACK BATTERY PACK BATTERY CHARGER BATTERY CHARGER BATTERY CHARGER BATTERY CHARGER BATTERY CHARGER USB CABLE AV CABLE HAND STRAP CD-ROM CD-ROM PACKING CASE PACKING CASE PACKING CASE PACKING CASE PACKING CASE PACKING CASE PACKING CASE PACKING CASE PACKING CASE PACKING CASE PACKING CASE PACKING CASE PACKING CASE PACKING CASE CUSHION BAG, POLYETHYLENE CD-ROM (INSTRUCTION BOOK) INSTRUCTION BOOK (ENGLISH) INSTRUCTION BOOK (SPANISH) INSTRUCTION BOOK (CANADIAN FRENCH) SIMPLIFIED O/I (ENGLISH/SPANISH) SIMPLIFIED O/I (PORTUGUESE) SIMPLIFIED O/I (SPANISH/PORTUGUESE) INSTRUCTION BOOK (ENGLISH) INSTRUCTION BOOK (RUSSIAN) INSTRUCTION BOOK (UKRAINIAN) INSTRUCTION BOOK (FRENCH) SIMPLIFIED O/I (GERMAN/FRENCH) SIMPLIFIED O/I (ITALIAN/DUTCH) SIMPLIFIED O/I (SWEDISH/DANISH) SIMPLIFIED O/I (POLISH/CZECH)
304 304 305 306 307 308 308 309 309 309 309 309 309 309 309 309 309 309 309 309 309 310 311 312 313 313 313 313 313 313 313 313 313 313 313 313 313 313
1 1 TZ5PR 1 TZ5EB,SG, TZ15GC 1 TZ5EE,EF,EG,E,SG, TZ15GC 1 TZ15GD 1 TZ15GK 1 TZ15GN 1 TZ15GT 1 TZ15GJ 1 TZ5P,PC 1 (EXCEPT TZ5P,PC) 1 TZ5P,PC,PL 1 TZ5PR 1 TZ5EB,EF,EG,E, TZ15GN 1 TZ5EE,SG, TZ15GC,GK,GJ,GD 1 TZ15GT 1 1 1 1 TZ5P,PC 1 (EXCEPT TZ5P/PC) 1 TZ5P-S,PC-S 1 TZ5P-K,PC-K 1 TZ5P-A,PC-A 1 TZ5PL-S,EE-S,EB-S,EF-S, EG-S,E-S,SG-S 1 TZ5PL-K,EE-K,PR-K,EB-K, EF-K,EG-K,E-K,SG-K 1 TZ5PL-A,EE-A,PR-A,EG-A, E-A 1 (-TA) 1 TZ5SG-T 1 TZ15GC-S,GJ-S,GN-S,GT-S 1 TZ15GC-K,GJ-K,GD-K,GN-K, GT-K 1 TZ15GC-T,GJ-T 1 TZ15GK-S 1 TZ15GK-K 1 TZ15GK-T 1 1 1 TZ5PL,PR,EG,SG, TZ15GC 1 TZ5P,PC 1 TZ5P
313
313 313 313 313 313 313 314 314
VQT1P95 VQT1P99 VQT1P97 VQT1P98 VQT1P96 VQT1Q79 VQT1M47 VQT1M48
314
VQT1M49
1 TZ5PR,EG
314 314 314 314
VQT1M52 VQT1M53 VQT1M51 VQT1M50
1 TZ5EB, TZ15GN 1 TZ5EE 1 TZ5EF 1 TZ5E
314
VQT1M54
1 TZ5SG, TZ15GC
314 314 314 314 315 315 317 317
VQT1M57 VQT1M56 VQT1M55 VQT1Q76 VYQ3680 VYQ4386 VPN6664 VPN6666
1 TZ15GD 1 TZ15GK 1 TZ15GT 1 TZ15GJ 1 (EXCEPT TZ15GK) 1 TZ15GK 1 TZ5PL,EE,PR,EF,EG,E, TZ15GK,GJ,GD,GN,GT 1 TZ5EB,SG, TZ15GC
1 TZ5PC 1 TZ5PL 1 TZ5PL 1 TZ5PR,EG 1 TZ5EB 1 TZ5EE 1 TZ5EE 1 TZ5EF 1 TZ5EG 1 TZ5EG 1 TZ5E 1 TZ5E
S-16
S7. Exploded View
S7.1. Frame and Casing Section
14 19 B19 17 5 23-2 23-1
37
23 B13 B11 26 9 18
33
29
23-4 13 15 23-3 23-5
36 38 B10 B3 25
B15
B16
41
202
B201 B202 B203
1
B20 35
31
2 40 B8
201 203
11 215 7 211 20 16 3 204
B208 B209 B210 205 B211 B207 B212 B213 B214 214 210 207 217 B6 B7
218
8 B4 B5 B14 B12 27 28 4 24 208
B17 B18
216
B9 24-1
B1
30 B2
S-17
S7.2. Packing Parts and Accessories Section
308 313 314 311 312 307 301 303 315 305
306 304 310 317 (Except P/PC areas.) 302 (Except P/PC areas.)
309
S-18