Text preview for : Sharp LC-32SH25E.pdf part of Sharp LC-32SH25E LCD TV Service Manual



Back to : Sharp LC-32SH25E.part1.ra | Home

LC-32SH25E

SERVICE MANUAL
No. SX8T4LC32SH25

LCD COLOUR TELEVISION MODELS

LC-32SH25E

In the interests of user-safety (Required by safety regulations in some countries) the set should be restored to its original condition and only parts identical to those specified should be used.

CONTENTS
SAFETY PRECAUTION IMPORTANT SERVICE SAFETY PRECAUTION ............................................................2 Precautions for using lead-free solder ................3 CHAPTER 1. OPERATION MANUAL [1] SPECIFICATIONS ..................................................4 [2] OPERATION MANUAL ...........................................5 [3] DIMENSIONS .......................................................10 CHAPTER 2. REMOVING OF MAJOR PARTS [1] REMOVING OF MAJOR PARTS ..........................11 CHAPTER 3. ADJUSTMENT PROCEDURE [1] ADJUSTMENT PROCEDURE .............................16 [2] SERVICE MODE ..................................................21 [3] SOFTWARE UPGRADE PROCEDURE...............22 CHAPTER 4. TROUBLESHOOTING TABLE [1] TROUBLESHOOTING TABLE..............................26 CHAPTER 5. MAJOR IC INFORMATIONS [1] MAJOR IC INFORMATIONS.................................39 CHAPTER 6. BLOCK DIAGRAM/WIRING DIAGRAM [1] VIDEO & AUDIO BLOCK DIAGRAM ...................59 [2] POWER MANAGEMENT BLOCK DIAGRAM ......60 [3] I2C and RS232 BLOCK DIAGRAM .......................61 [4] WIRING DIAGRAM ...............................................62 CHAPTER 7. PRINTED WIRING BOARD [1] MAIN UNIT PRINTED WIRING BOARD ...............63 [2] POWER UNIT PRINTED WIRING BOARD ..........65 [3] KEY UNIT PRINTED WIRING BOARD .................67 [4] IR UNIT PRINTED WIRING BOARD ....................68 CHAPTER 8. SCHEMATIC DIAGRAM [1] MAIN SCHEMATIC DIAGRAM ............................69 [2] POWER SCHEMATIC DIAGRAM .......................83 [3] KEY SCHEMATIC DIAGRAM .............................84 [4] IR SCHEMATIC DIAGRAM .................................85 CHAPTER 9. Parts Guide [1] SPARE PARTS LIST.............................................86 [2] CABINET PARTS ................................................108 [3] SUPPLIED ACCESSOORIES..............................110 [4] PACKING PARTS................................................111

Parts marked with "

" are important for maintaining the safety of the set. Be sure to replace these parts with specified ones for maintaining the

safety and performance of the set.

This document has been published to be used for after sales service only. The contents are subject to change without notice.

1

LC-32SH25E

SAFETY PRECAUTION
IMPORTANT SERVICE SAFETY PRECAUTION

Service work should be performed only by qualified service technicians who are thoroughly familiar with all safety checks and the servicing guidelines which follow: · Use an AC voltmeter having with 5000 ohm per volt, or higher, sen-

WARNING
1. For continued safety, no modification of any circuit should be attempted. 2. Disconnect AC power before servicing.

sitivity or measure the AC voltage drop across the resistor. · Connect the resistor connection to all exposed metal parts having a return to the chassis (antenna, metal cabinet, screw heads, knobs and control shafts, escutcheon, etc.) and measure the AC voltage drop across the resistor.

CAUTION: FOR CONTINUED PROTECTION AGAINST A RISK OF FIRE REPLACE ONLY WITH SAME TYPE FUSE. 42" F901 (T6.3AH/250V) 26"/32" F901 (T5AH/250V)

All checks must be repeated with the AC cord plug connection reversed. (If necessary, a nonpolarized adaptor plug must be used only for the purpose of completing these checks.) Any reading of 1.05 V peak (this corresponds to 0.7 mA peak AC.) or more is excessive and indicates a potential shock hazard which must be corrected before returning the monitor to the owner.

BEFORE RETURNING THE RECEIVER
(Fire & Shock Hazard)
Before returning the receiver to the user, perform the following safety checks: 3. Inspect all lead dress to make certain that leads are not pinched, and check that hardware is not lodged between the chassis and other metal parts in the receiver. 4. Inspect all protective devices such as non-metallic control knobs, insulation materials, cabinet backs, adjustment and compartment covers or shields, isolation resistor-capacitor networks, mechanical insulators, etc. 5. To be sure that no shock hazard exists, check for leakage current in the following manner. · Plug the AC cord directly into a 220~240 volt AC outlet. · Using two clip leads, connect a 1.5k ohm, 10 watt resistor paralleled by a 0.15µF capacitor in series with all exposed metal cabinet parts and a known earth ground, such as electrical conduit or electrical ground connected to an earth ground. ////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////// TO EXPOSED METAL PARTS CONNECT TO KNOWN EARTH GROUND 0.15 µF TEST PROBE DVM AC SCALE 1.5k ohm 10W

SAFETY NOTICE
Many electrical and mechanical parts in LCD color television have special safety-related characteristics. These characteristics are often not evident from visual inspection, nor can protection afforded by them be necessarily increased by using replacement components rated for higher voltage, wattage, etc. Replacement parts which have these special safety characteristics are identified in this manual; electrical components having such features are identified by " " and shaded areas in the Replacement Parts List and Schematic Diagrams. ////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////// For continued protection, replacement parts must be identical to those used in the original circuit. The use of a substitute replacement parts which do not have the same safety characteristics as the factory recommended replacement parts shown in this service manual, may create shock, fire or other hazards.

2

LC-32SH25E

Precautions for using lead-free solder
Using lead-free wire solder
· When fixing the PWB soldered with the lead-free solder, apply lead-free wire solder. Repairing with conventional lead wire solder may cause damage or accident due to cracks. As the melting point of lead-free solder (Sn-Ag-Cu) is higher than the lead wire solder by 40 °C, we recommend you to use a dedicated soldering bit, if you are not familiar with how to obtain lead-free wire solder or soldering bit, contact our service station or service branch in your area.

Soldering
· As the melting point of lead-free solder (Sn-Ag-Cu) is about 220 °C which is higher than the conventional lead solder by 40 °C, and as it has poor solder wettability, you may be apt to keep the soldering bit in contact with the PWB for extended period of time. However, Since the land may be peeled off or the maximum heat-resistance temperature of parts may be exceeded, remove the bit from the PWB as soon as you confirm the steady soldering condition. Lead-free solder contains more tin, and the end of the soldering bit may be easily corroded. Make sure to turn on and off the power of the bit as required. If a different type of solder stays on the tip of the soldering bit, it is alloyed with lead-free solder. Clean the bit after every use of it. When the tip of the soldering bit is blackened during use, file it with steel wool or fine sandpaper.

· Be careful when replacing parts with polarity indication on the PWB silk.

3

LC-32SH25E

CHAPTER 1. OPERATION MANUAL
[1] SPECIFICATIONS
Specification

Item

32" LCD Colour TV, Model: LC-32SH25E

LCD panel

32" diagonal 3,147,264 dots (1366 X 768 X 3 dots)

Number of dots Video Colour System TV-Standard Receiving Channel TV-Tuning System STEREO/BILINGUAL Backlight life Viewing angles Audio amplifier Speaker Antenna RS-232C SCART 1 SCART 2 Rear PC IN Component SPDIF AUDIO OUT HDMI 1 HDMI 2 C. I. (Common Interface) Headphones Side AV IN USB HDMI 3 Analogue Digital TV Function VHF/UHF CATV

PAL/SECAM/NTSC 3.58/NTSC 4.43/PAL 60 CCIR (B/G, I, D/K, L/L') DVB-T (2K/8K OFDM) ATV : IRA-E69, DVB-T : E5-E69 S-band, S1­S41ch Auto Preset 999 ch, Auto Label, Auto Sort NICAM/A2 60,000 hours (at Backlight Standard position) H : 176° V : 176° 5W X 2 (100 mm X 30 mm) X 2 UHF/VHF 75 D-Sub 3 pin male connector SCART (AV input, Y/C input, RGB input, TV output-analogue only) SCART (AV input, Y/C input, monitor output (analogue source - RF, SCART 1, SIDE AV) ) VGA pin (AV input), Ø 3.5mm jack (Audio output) Y/Pb(Cb)/Pr(Cr), RCA pin (L/R) Digital audio output RCA pin (L/R)

EN50221, R206001 Ø 3.5mm jack (Audio output) RCA pin (AV input) , RCA pin (L/R), S-VIDEO (Y/C input)
For service use only

Bulgarian, Croatian, Czech, Danish, Dutch, English, Finnish, French, German, Greek, Hungarian, OSD language Italian, Norwegian, Polish, Portuguese, Romanian, Russian, Serbian, Slovak, Slovene, Spanish, Swedish, Turkish Power Requirement Power Consumption AC 220­240 V, 50 Hz 150 W (Standby<1W) (Method IEC60107) 10.7 kg (Without stand), 12.5 kg (With stand) 0°C to + 40°C

Weight Operating temperature ·

As a part of policy of continuous improvement, SHARP reserves the right to make design and specification changes for product improvement without prior notice. The performance specification figures indicated are nominal values of production units. There may be some deviations from these values in individual units.

4

LC-32SH25E

[2] OPERATION MANUAL
Remote control unit
POWER
Press to turn the LCD TV on or enter standby mode.

MUTE
Press to toggle audio on and off. You can also press (+/-) VOL to restore the previous volume level.

VIDEO
Press this key you could select YPbPr, Side AV, HDMI 1, HDMI 2, HDMI 3.

DISPLAY
Press to display the current signal status, including input source/ channel audio mode.

SCART
Press this key you could select SCART 1, SCART 2.

MENU
Press to activate the LCD TV OSD. Press again to exit the LCD TV OSD.

PC
Press to direct to the PC mode.

TV
Press to direct to the TV mode.

EXIT
Press to exit LCD TV OSD.

OK 0-9 DIGIT BUTTONS
To select a TV channel directly. Press to activate a setting.


Press to navigate and confirm your selection.

EPG
Press this button to display electronic program guide in TV mode.

R/G/Y/B (Colour Button)
Press buttons to select the pictures with various colours of text. Different channels display different functions.·

PRE PR
To display the previous selected TV channel.

TELETEXT
Press this button to activate Teletext. Press again to turn off Teletext.

(INPUT SOURCE)
Select an input source.

ASPECT
Change the aspect ratio; please refer to Picture format section.

MIX
Press this button to activate Teletext with TV.

SIZE
Press this button to change the font size: Full screen, Top half and Bottom half.

DUAL
Select MONO, STEREO, DUAL 1 and DUAL 2 for ATV channel. Select Audio language for DTV channel.

SUBPAGE
To select the subpage when the current page contains subpage(s).

SLEEP
Press to turn the LCD TV off within an amount of time. (5-180 minutes.)

INDEX
Press this button to return to page 100 or the index page; and then press 0 to 9. The teletext page will be numbered and added to the page you select or the secondary item.

PICTURE
Press to set the LCD TV to a predefined picture setting. User / Cinema / Sport / Vivid / Hi-Bright

PR LIST
Press to display a list of channels. Then press Red button to select the Digital or Analogue channel list.

SUBTITLE
For DTV, press it to select subtitle setting. off / on / on during mute For ATV, please activate Teletext to select subtitle page.

SOUND
Press to set the LCD TV to a predefined sound setting. Off / Rock / Pop / Live / Dance / Techno / Classic / Soft

HOLD
Press this button to stop the scrolling of pages. The text decoder stops receiving data.

REVEAL
Reveal hidden information such as answers to a quiz.

(+/-)
Press to adjust the volume.

P(/)
Press to select the channel.

2008-03-14

5

LC-32SH25E

TV (Front view)

(Standby/On) indicator

Remote control sensor

TV (Rear view)

(+/-) Volume buttons

12
P( / ) Programme [channel] buttons P MENU button (INPUT SOURCE) button (Power) button MENU

13 14

15 16 1 17

5
PC IN

2 3

9

SERVICE AUDIO VGA COMPONENT

10

HDMI1

6
HDMI2

Y

Pb

Pr

11 7

4
L R SPDIF OUT

8

AUDIO OUT L R

SCART1

SCART2

1 Power connector 2 SERVICE socket 3 HDMI 1 4 HDMI 2 5 PC IN (VGA/AUDIO) 6 Component Video and L/R Audio input 7 SPDIF Output (Digital audio out) 8 AV L/R Audio Output 9 SCART 1 (CVBS Tuner out) 10 SCART 2 (CVBS Monitor out) 11 Tuner Input 12 COMMON INTERFACE slot 13 Earphone Output 14 Composite ( AV IN, AV/LR) 15 S-Video 16 SERVICE socket(For LC-32SH25E) 17 HDMI 3

6

LC-32SH25E

Preparation
Mount the TV Stand
1. Put the TV face down on a safe surface that is covered by a soft and smooth cloth. 2. 3. Adjust the TV stand to the base column. Fasten 4 screws.

3

Wall mounting
TV screen size ( inches) 32" 1. 2. Put the TV face down on a safe surface that is covered by a soft and smooth cloth. Unscrew the 4 bolts that fasten the base column to the TV by using a cross-head screwdriver. (not supplide) Detach the stand from the bottom of the TV. VESA-compatible wall bracket (millimeters) (W x H) 200 x 200 mm

Screw type Metric 6 x 10 mm

3

3.

2008-03-14

7

LC-32SH25E

preparation
Installation of batteries
1. insert two AAA batteries into Remote control. Make sure (+) and (-) are facing the proper direction. 2. Replace the cover.

NOTE · If the remote control will not to be used for a long time, remove the batteries to avoid remote control damage. CAUTION Improper use of batteries can result in chemical leakage or explosion. Be sure to follow the instructions below. · Do not mix batteries of different types. Different types of batteries have different characteristics. · Do not mix old and new batteries. Mixing old and new batteries can shorten the life of new batteries or cause chemical leakage in old batteries. · Remove batteries as soon as they have worn out. Chemicals that leak from batteries can cause a rash. If you find any chemical leakage, wipe thoroughly with a cloth. · The batteries supplied with this product may have a shorter life expectancy due to storage conditions. · If you will not be using the remote control unit for an extended period of time, remove the batteries from it. Note on disposing batteries: The batteries provided contain no harmful materials such as cadmium, lead or mercury. Regulations concerning used batteries stipulate that batteries may no longer be thrown out with the household Rubbish. Deposit any used batteries free of charge into the designated collection containers set up at commercial Businesses.

Using the remote control unit
Use the remote control unit by pointing it towards the remote control sensor. Objects between the remote control unit and sensor may prevent proper operation.

Bundling the cables

Remote control sensor 5m

30

30

8

LC-32SH25E

Appendix
troubleshooting
problem No picture possible Solution 1. Connect power cord correctly. 2. Turn on power. 3. Connect signal cable correctly. 4. Press any button on the LCD TV. Connect signal cable correctly. 1. Connect signal cable correctly. 2. Please use compatible signal. Adjust brightness and contrast. 1. Please check if input signal is connected correctly. 2. TV-RF signal must not be lower than 50dB. 1. Connect signal cable correctly. 2. Adjust volume to proper level. 3. Connect audio signal cable correctly. 4. TV-RF signal must not be lower than 50dB. 1. Please change battery. 2. Turn off power for 10 seconds; and then restart power. Please use the Channel scan function to increase the number of channels not included in memory. Please adjust the colour setup 1. Check the connection of antenna/signal cable. 2. Check if channel is in play mode. 3. Press signal source and change input mode. Adjust antenna. Keep the TV away from noise sources, such as automobiles, neon lights, and hair dryers. Please use the Update scan method to add the channels not included in memory Please use multi-directional outdoor antenna. (If your TV is subject to the influence of nearby mountains or buildings). If the item you choose turns gray, that item cannot be selected. Please use the Update scan method to add the channels not included in memory. 1. If the lamp(s) is(are) broken, panel inverter will not kick on the lamps, so TV set phenomena will be "no picture on display." But the TV system is still working, that is the RC can also control LED. When AC power on, the LED will keep last status and when use RC DC power on, the LED will keep green light. 2. The failed panel should be sent back to Panel maker (CMO) via RMA process. Panel maker (CMO) will not rework the lamps at customer's side since the repaired panel should be checked through regular inspection flow to secure the quality.

Abnormal colours Twisted picture Picture too dark Audio only, no images Picture only, no audio

Cannot use remote control Cannot receive sufficient channels through antenna No colours Blinking picture accompanied by ghost image Broken lines or segments

Certain TV channels are blocked (Hope to acquire some channels) Overlapping images or ghost images Cannot use a function Cannot receive programs 1. When a lamp in LCD panel is broken and the protector circuit in inverter operates and we tune on the this set, LED keep red? or Green? 2. Service man only change the lamp in LCD panel?

Cautions regarding use in high and low temperature environments · When the unit is used in a low temperature space (e.g. room, office), the picture may leave trails or appear slightly delayed. This is not a malfunction, and the unit will recover when the temperature returns to normal. · Do not leave the unit in a hot or cold location. Also, do not leave the unit in a location exposed to direct sunlight or near a heater, as this may cause the cabinet to deform and the LCD panel to malfunction. · Storage temperature: +5°C to +35°C.

information on the software license for this product
Software composition The software included in this product is comprised of various software components whose individual copyrights are held by SHARP or by third parties. Software developed by SHarp and open source software The copyrights for the software components and various relevant documents included with this product that were developed or written by SHARP are owned by SHARP and are protected by the Copyright Act, international treaties, and other relevant laws. This product also makes use of freely distributed software and software components whose copyrights are held by third parties. These include software components covered by a GNU General Public License (hereafter GPL), a GNU Lesser General Public License (hereafter LGPL) or other license Agreement. obtaining source code Some of the open source software licensors require the distributor to provide the source code with the executable software components. GPL and LGPL include similar requirements. For information on obtaining the source code for the open source software and for obtaining the GPL, LGPL, and other license agreement information, visit the following website: http://www.sharp-eu.com/gpl/ We are unable to answer any questions about the source code for the open source software. The source code for the software components whose copyrights are held by SHARP is not distributed. acknowledgements The following open source software components are included in this product: 2008-03-14 ·linuxkernel·modutils·glibc·zlib·libpng

9

LC-32SH25E

[3] DIMENSIONS

10

LC-32SH25E

CHAPTER 2. REMOVING OF MAJOR PARTS
[2] REMOVING OF MAJOR PARTS(LC-32SH25)
1. Assy/Panel Removal
Notes: Please put your machine on soft material to avoid to scrape panel when you disassemble it. Front view

Fig.1 Back view

Fig.2 Step 1. Remove the Base Assy. 1. Remove the base as Fig.3. Remove the 4 screws as Fig.3 and pull out the base as Fig.4

Fig.3

2008-03-14

11

LC-32SH25E

Fig.4 2. Remove the 4 screws. Detach the BASE STAND as Fig.5.

Step 2. Remove the REAR COVER Assy. 1. Remove the 11 screws. Detach the REAR COVER as Fig.5.

Fig.5 Step 3. Remove the Main, Power, IR, Key board and the Speakers.

Fig.6 1. Remove the 6 screws and disconnect 4 cables. Detach the Main board as Fig.7 and Fig.8.

12

LC-32SH25E

Fig.7

Fig.8 2. Remove the 5 screws and disconnect 2 cables. Detach the Power board as Fig.9.

Fig.9 3. Remove the 1 screw and disconnect 1 cable. Detach the IR board as Fig.10.

Fig.10 4. Disconnect 1 cable. Detach the Key board as Fig.11.

2008-03-14

13

LC-32SH25E

Fig.11 5. Remove the 4 screws and disconnect 4 cables. Detach the Speakers as Fig.12 and Fig.13.

Fig.12 Step 4. Remove the Metal Frame. 1. Remove the 6 screws and disconnect 2 cables. Detach the Metal Frame as Fig.14.

Fig.13

Fig.14 Step 5. Remove the Bezel Assy. 1. Remove the Bezel Assy as Fig.15

Fig.15 2. The below picture is panel as Fig.16.

14

LC-32SH25E

Fig.16

2. Set Re-assembly
To re-assemble the whole set, execute all processes in reverse order. Notes: a. While re-assembling, make sure that all cables are placed and connected in their original position. b. Pay special attention not to damage the EMC foams at the SSB shielding. Check that EMC foams are put correctly on their places.

2008-03-14

15

LC-32SH25E

CHAPTER 3. ADJUSTMENT PROCEDURE
PROCEDURE
[1] ADJUSTMENT PROCEDURE
1. OSD Menu
OSD tree - As following

·

TV

Digital Europe OSD tree-TV OSD Layer 1 Picture 2 Smart Picture 3 User Cinema Sport Vivid Hi-bright Contrast Brightness Color Sharpness Tint Color temperature slider slider slider slider slider Normal Warm Cool Picture format Automatic Super zoom 4:3 Movie expand 14:9 Movie expand 16:9 Wide screen Subtitle zoom Noise Reduction Sound Settings Off On Bass Treble Sound mode Balance Off Rock Pop Live Dance Techno Classic Soft Virtual surround Volume-visually impaired Audio language Dual I-II Mono/Stereo Auto volume leveling Off On slider Broadcsted list of audio languages Dual I Dual II Mono Stereo Off On slider slider slider 4 5 6

Remark

16

LC-32SH25E
Features Timer Clock Time zone GMT +x:xx GMT -x:xx As broadcaster Auto synchronization On Off Date Time Start time Timer Off On Stop time Sleeptimer Auto lock Lock program Change code Clear all Parental rating Timer slider (Channel number...) Please enter your current PIN. Start now None Age 4~18 X-rated(Spain) Subtitle Off On On during mute Subtitle language Common interface Installation Language Menu language Cesky Dansk Deutsch English Español Français Hrvatski Italiano magyar Nederlands Norsk Polski Português Român Slovenský Slovenscina Srpski Suomi Svenska Türkçe Preferred audio language Basque Bulgarian Catalan Croatian Czech Danish Dutch Broadcsted list of audio languages (When CAM inserted) Off On 20xx/xx/xx xx:xx:xx

Time

2008-03-14

English Finnish

17

LC-32SH25E
French Gaelic Galician German Greek Hungarian Italian Norwegian Polish Portuguese Romanian Russian Serbian Slovak Slovenian Spanish Swedish Turkish Welsh Preferred subtitle language Basque Bulgarian Catalan Croatian Czech Danish Dutch English Finnish French Gaelic Galician German Greek Hungarian Italian Norwegian Polish Portuguese Romanian Russian Serbian Slovak Slovenian Spanish Swedish Turkish Welsh Hearing impaired Audio description Country France Status: scanning... Digital channels found: Analoguel channels found: Status: scanning... Start Network name: Signal quality:Good/Poor Off On Off On

Channel installation

Automatic installation

Start now

Installation update Digital: Test reception

Start now 000.00 MHz

18

LC-32SH25E
Signal strength: Analog: Manual installation System West EU East EU UK France Search 000 MHz Fine tune 000.00 MHz Store current channel Store Store as new channel Store (Channel numbers...) Rename,reshuffle No label DVD Blu-ray HDD/DVDR HD rec. Game VCR PC Digital STB HD dig STB Other Decoder Current software info Factory reset · Start now (Channel numbers...)

Rearrange Source labels YPbPr Side AV SCART 1 SCART 2 PC HDMI 1 HDMI 2 HDMI 3

PC

Digital Europe OSD tree-PC OSD Layer 1 Picture Contrast Brightness Colour Temperature 2 slider slider Normal Warm Cool Picture format 4:3 Wide screen Sound Incredible surround Off On Picture adjustment Auto adjust Manual adjust Start Phase Clock Horizontal Vertical Factory reset Start now slider slider slider slider 3 4 5

Remark

2008-03-14

19

LC-32SH25E

2. Picture check
1) WHITE-D adjustment
General set-up :
Equipment Requirements: Minolta CA-210 or Equivalent Color analyzer Chroma 2250 or equivalent PC signal generator input requirements: Input Signal Type : PC VGA signal 1280 X 1024/60Hz PC mode with "5 white block" pattern. (see pattern-1) Input Signal Strength : 0.7 Vp-p linear voltage. Input Injection Point : PC D-SUB input

Pattern-1 Alignment method: Initial Set-up: 1>. Select source as "PC". 2>. Set Contrast = 50 (Sharp) and Brightness=50 (Sharp) , at normal menu mode. 3>. Apply "5 white block"(pattern-1) pattern by VGA pattern generator. 4>. Enter factory mode menu: press MENU + Numeric keys "062596" + MENU key (FAC mode menu). Then select "Factory" item. Alignment: 1>. At FAC mode menu, select AUTO_COLOR item. Then press "OK" key to adjust ADC_GAIN_R, ADC_GAIN_G, ADC_GAIN_B and ADC_OFFSET_R, ADC_OFFSET_G, ADC_OFFSET_B. Then store those values to NVM. 2>. Apply Flat80 pattern (80% white pattern). 3>. Set color temperature to "NORMAL". 4>. At FAC mode menu, adjust the CLR TEMP R, CLR TEMP G, CLR TEMP B values to meet "NORMAL" color coordinates specification below. Then store those values to NVM 5>. Set color temperature to "COOL". 6>. At FAC mode menu, adjust the CLR TEMP R, CLR TEMP G, CLR TEMP B values to meet "COOL" color coordinates specification below. Then store those values to NVM 7>. Set color temperature to "WARM". 8>. At FAC mode menu, adjust the CLR TEMP R, CLR TEMP G, CLR TEMP B values to meet "WARM" color coordinates specification below. Then store those values to NVM Color temperature Normal/Warm/Cool (x, y) co-ordinates specification: Picture Mode o Normal (9000 K) o Cool (12000 K) o Warm (6500 K) x 0.289±0.003 0.272±0.003 0.314±0.003 Table 5: Reading with Minolta CA-210. Note: 1>. Use Minolta CA-210 for color coordinates and luminance check. 2>. Befor adjusting,all colour analyzers (CA-210) should be coordinates with a same reference TV set. 3>. Luminance > 400 cd/m in the center of the screen when Brightness control at 100; Contrast control at 100 for Sharp 32" panels.
2

y 0.291±0.003 0.277±0.003 0.319±0.003

20

LC-32SH25E

[2] SERVICE MODE
Enter factory mode menu: press MENU + Numeric keys "062596" + MENU key (FAC mode menu).Then select "Factory" item.

2008-03-14

21

LC-32SH25E

[3] SOFTWARE UPGRADE PROCEDURE
Environment Setup

Before you start to write the code, we suggest you setup the environment first. This chapter lists the setup requirements and guides you to setup and test your development environment.

1.1 Connect to ISP Board to upgrade the software firmware.

Use USB port connecting PC & MT536x Board via ISP board(Code number: 9JR9900000099(715G537XL2)).
To PC USB port

To system board service port

Example: PC Connected to system board service port ( From USB to RS232).

1. Unzip USB2COM Driver.zip to C:\

PL-2303 Driver Installer.rar
I. PL-2303 Driver Installer.exe II. Double click exe file to install driver

mtktool_mt5391.rar

2. Use MTK_Tools to download .bin file. (Ex: SHARP_LC_32SH25E__Vxx.xx_image.bin)

3. Make sure the Type "MTK539X" && "USB Baud Rate 115200x8" && Load the correct "bin" file.

Detailed operation sequence listed as follows. Load .bin file on the Linux system or on the local Windows file system(Ex: SHARP_LC_32SH25E__Vxx.xx_image.bin) & Set Bridge & Auto Set Flash BaudRate.

22

LC-32SH25E
BaudRate.

4. Set COM port resource that used by USB Port.

5. Set Baud rate 115200x8 & High speed item Enable. & MT539x.

2008-03-14

23

LC-32SH25E

6. Push "Upgrade" button. (Waiting for "Finished!" message.)

Press "" button

7. Mainboard Power Off

On.

24

LC-32SH25E
1.2 Connect to TV USB port to upgrade the software firmware

Please follow the following step to upgrade the firmware.

1. Copy the software firmware (*.pkg) to USB Disk. 2. Modify the pkg's filename to "upgrade.pkg" 3. Insert the USB Disk to TV USB port.

4. TV AC power off -> AC power on 5. TV will upgrade by itself after detect the USB disk condition and the content of the pkg file. Note: TV's Green LED will flash during upgrade process 6. After finish upgrade process, TV will reboot by itself. 7. Remove USB disk from TV. 8. Check the software version is correct or not. (Menu / setup / Current software info)

2008-03-14

25

LC-32SH25E

CHAPTER 4. TROUBLESHOOTING TABLE
[1] TROUBLESHOOTING TABLE
Power unit operation check.


Are the power cord and harness in the unit properly connected?

NO

Connect the power cord and harness properly, and turn on the power.

LINE_FILTER_UNIT:
Is F901 normal?

YES
LINE_FILTER_UNIT: Isn't L901,L902,RV901,C903,C904,C901,C902, etc. out of order? Moreover, whether the short-circuit with the circumference circuit is checked. POWER_UNIT: BD901, RV902, IC951, etc. out of order? Moreover, whether the short-circuit with the circumference circuit is checked.

NO

POWER_UNIT

YES NO
Does the PFC circuit operate normally? (L906, Q901, D902, D903, IC901 and etc. And, the circuit around the protection circuit etc. is checked.)

Is BD901 (+320V) output? (Set the main power SW to OFF.) * When power on/off switch is on About +400V

YES
Is a voltage of +5V applied to pin (11,12) of connector (CN902)? (Set the main power SW to OFF.)

NO

Does the switching circuit operate normally? Check circuit around the primary side (T901, IC931, Q931, ZD981, ZD930, D980, D981, ZD981, etc.), the secondary side (D935, L980, etc.), the AC_DET circuit (ZD982, IC932, IC982, Q992, Q993, etc.), and the protection circuit.

YES
Are +24V output as for the power on/off switch when it is on?

NO

Does the inverter circuit operate normally? Check circuit around the primary side (T902,Q951,Q952,IC951, D951,D952, etc.), the secondary side (D955, L971, ZD967, IC952, IC953, etc.), the STANDBY circuit (Q988, etc.), and the protection circuit.

YES
Similarly, is +12V output as for the power on/off switch when it is on?

NO

Check +12V circuit of D956, L931, etc.

26

LC-32SH25E
The sound is not emitted from the speaker though the picture has come out.


No sound output in all modes? TEREMINAL UNIT:

NO
Check IC U400 and its peripheral circuits.

Is the audio signal output of pin (H26) (AL0) and pin (H25) (AR0) of IC U400 normal?

YES
Is the audio signal output of pin (17) (PGA2OUTL) and pin (18) (PGA2OUTR) of IC U605 normal?

NO

Check IC U605 and its peripheral circuits.

YES
Is audio signal input to pin (2)(L), pin (14)(R) of IC U600 (AMP)?

NO

Check the line between IC U605 and IC U600.

YES
Is MUTE circuit [AMP_MUTE_LINE, POWERUP_LINE] normal?

NO

Check the AMP_MUTE_LINE and POWERUP_LINE. (Q600, etc.)

YES
Is the audio signal output of pin (3, 4) (L-ch) and pin (1, 2) (R-ch) of CN600 (AOUDIO-CONNECTOR) normal?

NO

Check IC U600 and its peripheral circuits.

YES
Check Speaker Box (right and left) and wire harness.

No sound (during the reception of TV(ANALOG) broadcasting)


Does not the sound go out though the picture has come out when UHF/VHF is received? TEREMINAL UNIT:

NO
Check the tuner and its peripheral circuits. Replace as required.

Is the SIF signal output from pin (11) of TUNER (TU200)?

YES
Is the SIF signal sent to pin (AB25) and pin (AB26) of IC U400?

NO

Check IC U400 its peripheral circuits.

YES
Refer to "No sound output in all modes".

2008-03-14

27

LC-32SH25E
No sound (during the reception of TV (DIGITAL) broadcasting)


Does not the sound go out though the picture has come out when DTV is received? MAIN UNIT:

NO
Check the tuner and its peripheral circuits. Replace as required.

Is the DIF signal output from pin (17) and pin (19) of TUNER (TU200)?

YES
Is the DIF signal sent to pin (R25) and pin (T25) of IC U400?

NO

Check IC U400 its peripheral circuits.

YES
Refer to "No sound output in all modes". No sound from external input devices (1)


Does not the sound of the audio signal input to SCART1 go out? Does not the sound of the audio signal input to SCART2 go out? TEREMINAL UNIT:

NO NO
Check the setting of an external input device that connects of CN500. Check the setting of an external input device that connects of CN501.

Is the audio signal properly sent to pin (6) (SCT1_AUL_IN) and pin (2) (SCT1_AUR_IN) of SCART1(CN500)? Is the audio signal properly sent to pin (6) (SCT2_AUL_IN) and pin (2) (SCT2_AUR_IN) of SCART2(CN501)?

YES
Is the audio signal properly sent to pin (44) (SC1_LIN) and pin (43) (SC1_RIN) of IC U605? Is the audio signal properly sent to pin (46) (SC2_LIN) and pin (45) (SC2_RIN) of IC U605?

NO NO

Check the line between CN500 and IC U605.

Check the line between CN501 and IC U605.

YES
Refer to "No sound output in all modes". No sound from external input devices (2)


Does not the sound of the audio signal input to AV1(Component) go out? MAIN UNIT:

NO
Check the connection to CN553 and the external input device.

Is the audio signal properly sent to pin (2) (AV1_AudioLIN) and pin (4)(AV1_AudioRIN) of CN553?

YES
Is the audio signal properly sent to pin (50) (AV1_LIN) and pin (49) (AV1_RIN) of IC U605?

NO

Check the line between CN553 and IC U605.

YES
Refer to "No sound output in all modes".

28

LC-32SH25E
No sound from external input devices (3)


Does not the sound of the audio signal input to AV3(Composite/Y/C) go out? MAIN UNIT:

NO
Check the connection to CN650 and the external input device.

Is the audio signal properly sent to pin (4) (AV3_AudioLIN) and pin (6) (AV3_AudioRIN) of CN650?

YES
Is the audio signal properly sent to pin (52) (SIDE_LIN) and pin (51) (SIDE_RIN) of IC U605?

NO

Check the line between CN650 and IC U605.

YES
Refer to "No sound output in all modes". No sound from external input devices (4)


Does not the sound of the audio signal input to VGA go out? MAIN UNIT:

NO
Check the connection to CN555 and the external input device.

Is the audio signal properly sent to pin (2) (VGA_AudioLIN) and pin (3) (VGA_AudioRIN) of CN555?

YES
Is the audio signal properly sent to pin (48) (VGA_LIN) and pin (47) (VGA_RIN) of IC U605?

NO

Check the line between CN555 and IC U605.

YES
Refer to "No sound output in all modes". No sound from external input devices (5)


Does not the sound of the audio signal input to HDMI1/2/3 go out?


Is picture of the signal input from HDMI1/2/3 displayed?

NO

Refer to "Does not the picture of the HDMI signal input to HDMI1/2/3 go out?".

YES
Refer to "No sound output in all modes".

2008-03-14

29

LC-32SH25E
The audio signal is not output (1)


The audio signal of UHF/VHF is not output from SCART1. TEREMINAL UNIT:

YES
Check the connection to SCART1 and external devices.

Is audio signal output from IC U602 sent to pin (3)(SCT1_AULOUT) and pin(1)(SCT1_AUR-OUT) of SCART1(CN500)?

NO
Is audio signal output from IC U400 sent to pin (2)(LRCLK) and pin (3)(DIN) and pin (4)(BCLK) and pin(13)(MCLK) of IC U602?

YES

Check the line between IC U400 and IC U602.

NO
Check IC U400 and its peripheral circuits.

The audio signal is not output (2)


The audio signal of UHF/VHF/MONITOR is not output from SCART2. TEREMINAL UNIT:

YES
Check the connection to SCART2 and external devices.

Is audio signal output from IC U605 sent to pin(3)(SCT2_AUL_OUT) and pin(1)(SCT2_AUR_OUT) of

NO
Is the audio signal output from IC U400 pin(K26) (AL2) and pin(J24) (AR2) sent to pin(26)(INPUT1L) and pin(25)(INPUT1R) of IC U605?

YES

Check the line between IC U400 and IC U605.

NO
Check IC U400 and its peripheral circuits.

The audio signal is not output (3)


No audio signal output from LINE_AUDIO_OUTPUT terminal. TEREMINAL UNIT:

YES
Check the connection to LINE_AUDIO_OUT and external devices.

Is audio signal output from IC U605 sent to pin(2)(L_OUT) and pin (4)(R_OUT) of LINE_AUDIO_OUT connector(CN556)?

NO
Is the audio signal output from IC U400 pin(K26) (AL2) and pin(J24) (AR2) sent to pin(26)(INPUT1L) and pin(25)(INPUT1R) of IC U605?

YES

Check the line between IC U400 and IC U605.

NO
Check IC U400 and its peripheral circuits.

30

LC-32SH25E
The audio signal is not output (4)


No audio signal output from SPDIF_OUTPUT terminal. TEREMINAL UNIT:

YES
Check the connection to SPDIF_OUT and external devices.

Is ASPDIF audio signal output from pin (E26) of IC U400 to pin (6) of connector CN553?

NO
Check IC U400 and its peripheral circuits. The audio signal is not output (5)


No sound from HEADPHONE_OUTPUT terminal. MINI AV_UNIT:

NO
Check the connection to CN602 and external headphone is plug in well.

Is the HPDET signal input into pin (AA5) of IC U400 from pin (7) of a headphone terminal (CN602)?

YES
Is the audio signal output from IC U605 to pin(2) (HPOUTL) and pin (3) (HPOUTR) of headphone terminal CN602?

NO

Check the line between IC U605 and CN602.

YES
Is the audio signal output from IC U400 pin(J26)(AL1) and pin(J25) (AR1) sent to pin(24)(INPUT0L) and pin(23)(INPUT0R) of IC U605?

NO

Check the line between IC U400 and IC U605.

YES
Check IC U400 and its peripheral circuits.

2008-03-14

31

LC-32SH25E
No picture on the display (1)


The picture doesn't appear in all modes. MAIN UNIT:



Is LVDS signal output from 1st_channel and 2nd_channel of IC U400 in each mode? (A0N/A0P),(A1N/A1P),(A2N/A2P),(A3N/A3P),(CLK1N/CLK1P)

NO YES
Is the above-mentioned LVDS signals output to connector CN750? Check IC U400 and its peripheral control circuits.

NO

Check the line between IC U400 and CN750.

YES
Is LCD controller's control signal normal?

NO

Control signals BRIGHT_ADJ, INVERTER_ON_OFF, PANEL_VCC_ON/OFF, and it peels off and whether normality is checked.

PANEL_UNIT:

YES NO
Wire harness is checked.

Similarly, is the LVDS signal input to connector of the panel module?

YES
Check the panel module.

No picture on the display (2)


Does not the picture come out when VHF/UHF is received? TERMINAL UNIT:

NO
Check whether I2C is normally accessed between TU200 and IC U400.

Is TUNER_CVBS signal output from pin (21) of TUNER (TU200)?

MAIN_UNIT:

YES NO
Check the line between IC U400 and TU200.

Is picture signal input from pin (21) of TUNER (TU200) to pin (AB24) of IC U400?

YES
Refer to "The picture doesn't appear in all modes."

32

LC-32SH25E
No picture on the display (3)


Does not the picture come out when DTV is received? TERMINAL UNIT:

NO
Each power supply circuit is checked.

Is the voltage of regulation for a TUNER circuit and the power supply terminal of IC U400 supplied?

YES
Is IF signal output from pin (17), (19) of TUNER (TU200) to pin (R25), pin (T25) of IC U400 ?

NO

Check the tuner, IC U400 and their peripheral circuits. Replace as required.

YES
Is MPEG data (TS0INDATA0, TS0INSYNC, TS0INCLK, TS0INVALID) from IC U400 are output to pin (9), pin (7), pin (6), pin (8) of a IC U401? MAIN_UNIT:

NO

is communication control carried out between pin (6)(SCL), pin(9)(SDA), of TU200, and pin(F24)(TUNER_SCL1), pin (F25)(TUNER_SDA1), of IC U400?

YES NO
Check X300/ X400 and its peripheral circuits.

Do X300 (60.00MHz)/ X400 (27MHz) oscillate?

YES
Is MPEG data (TS_DATAO, TS_CKO, TS_VALIDO, TS_SYNCO) from IC U401 are output to pin (B21/A21/B20/C21) of a IC U400?

NO

Is the control signal between IC U401 and IC U400 normal? (RESET_CI, etc.).

YES
Refer to "The picture doesn't appear in all modes."

2008-03-14

33

LC-32SH25E
No picture on the display (4)


Does not the picture of the CVBS signal input to SCART1 go out? Does not the picture of the CVBS signal input to SCART2 go out? TERMINAL UNIT:

NO NO
Check the setting of an external input device that connects of CN500. Check the setting of an external input device that connects of CN501.

Is CVBS signal sent to pin (20) of SCART1 (CN500)? Is CVBS signal sent to pin (20) of SCART2 (CN501)? MAIN_UNIT:

YES NO NO
Check the line between IC U400 and CN500. Check the line between IC U400 and CN501.

Is CVBS signal sent to pin (AE24) of IC U400? Is CVBS signal sent to pin (AE26) of IC U400?

YES
Refer to "The picture doesn't appear in all modes."

No picture on the display (5)


Does not the picture of the R/G/B video signal input to SCART1 go out? TERMINAL UNIT:

NO
Check the setting of an external input device that connects of CN500.

Is RGB signal sent to pin (15)/R, (11)/G, (7)/B, of SCART1 (CN500)? MAIN_UNIT:

YES NO
Check the line between IC U400 and CN500.

Is RGB signal sent to pin (AF24)/R, (AD24)/G, (AD23)/B of IC U400?

YES
Refer to "The picture doesn't appear in all modes."

34

LC-32SH25E
No picture on the display (6)


Does not the picture of the Y/C signal input to SCART1 go out? Does not the picture of the Y/C signal input to SCART2 go out? TERMINAL UNIT:

NO NO
Check the setting of an external input device that connects of CN500. Check the setting of an external input device that connects of CN501.

Is Y/C signal sent to pin (20) and (15) of SCART1 (CN500)? Is Y/C signal sent to pin (20) and (15) of SCART2 (CN501)?

MAIN_UNIT:

YES NO NO
Check the line between IC U400 and CN500. Check the line between IC U400 and CN501.

Is Y/C signal sent to pin (AE24)/Y, (AF25)/C of IC U400? Is Y/C signal sent to pin (AE26)/Y, (AE25)/C of IC U400?

YES
Refer to "The picture doesn't appear in all modes."

No picture on the display (7)


Does not the picture of the composite video signal input to AV3(Composite) go out? TERMINAL UNIT:

NO
Check the setting of an external input device that connects of CN650.

Is CVBS signal sent to pin (2) of AV3 (CN650) ?

MAIN_UNIT:

YES NO
Check the line between IC U400 and CN650.

Is CVBS signal sent to pin (AC24) of IC U400?

YES
Refer to "The picture doesn't appear in all modes."

No picture on the display (8)


Does not the picture of the Y/C video signal input to AV3(Y/C) go out? TERMINAL UNIT:

NO
Check the setting of an external input device that connects of CN650.

Is Y/C signal sent to pin (8)/Y, (7)/C of AV3 (CN650) ?

MAIN_UNIT:

YES NO
Check the line between IC U400 and CN650.

Is Y/C signal sent to pin (AD26)/Y, (AD25)/C of IC U400?

YES
Refer to "The picture doesn't appear in all modes."

2008-03-14

35

LC-32SH25E
No picture on the display (9)


Does not the picture of the HDMI signal input to HDMI1 go out? MINI AV_UNIT:

NO
Check the line between pin (AC4) of IC U400 and CN702.

Is the HOT_PLUG detection function of pin (19) of a HDMI terminal (CN702) normal?


Check the connection and setup with the external HDMI devices.

YES
Are EDID data pin (6)(SCL) of IC U708 (EEPROM), pin (5)(SDA) accessed, and is it read from pin (15), pin (16) of a HDMI terminal(CN702)?

NO

Is access possible in the re-writing or exchange of EDID data of IC U708?

NO YES
Is TMDS signal input into pin (AF10, AE10)/RX2±, (AF9, AE9)/RX1 ±, (AF8, AE8)/RX0±, (AF7, AE7)/RXC± of IC U400? Check CN702, IC U708 and peripheral circuits.

NO

Check the line between IC U400 and CN702.

YES
Refer to "The picture doesn't appear in all modes."

No picture on the display (10)


Does not the picture of the HDMI signal input to HDMI2 go out? MINI AV_UNIT:

NO
Check the line between pin (AA6) of IC U400 and CN700.

Is the HOT_PLUG detection function of pin (19) of a HDMI terminal (CN700) normal?


Check the connection and setup with the external HDMI devices.

YES
Are EDID data pin (6)(SCL) of IC U701 (EEPROM), pin (5)(SDA) accessed, and is it read from pin (15), (16) of a HDMI terminal(CN700)?

NO

Is access possible in the re-writing or exchange of EDID data of IC U701?

NO YES
Is TMDS signal input into pin(AF14, AE14)/RX2±, (AF13, AE13)/RX1±, (AF12, AE12)/RX0±, (AF11, AE11)/RXC± of IC U400? Check CN700, IC U701 and peripheral circuits.

NO

Check the line between IC U400 and CN700.

YES
Refer to "The picture doesn't appear in all modes."

36

LC-32SH25E
No picture on the display (11)


Does not the picture of the HDMI signal input to HDMI3 go out? MINI AV_UNIT:

NO
Check the line between pin (AB5) of IC U400 and CN701.

Is the HOT_PLUG detection function of pin (19) of a HDMI terminal (CN701) normal?


Check the connection and setup with the external HDMI devices.

YES
Are EDID data pin (6)(SCL) of IC U700 (EEPROM), pin (5)(SDA) accessed, and is it read from pin (15), (16) of a HDMI terminal(CN701)?

NO

Is access possible in the re-writing or exchange of EDID data of IC U700?

NO YES
Is TMDS signal input into pin (AF18, AE18)/RX2±, (AF17, AE17)/RX1±, (AF16, AE16)/RX0±, (AF15, AE15)/RXC± of IC U400? Check CN701, IC U700 and peripheral circuits.

NO

Check the line between IC U400 and CN701.

YES
Refer to "The picture doesn't appear in all modes."

No picture on the display (12)


Does not the picture of the PC IN(ANALOG) video signal input to VGA(15pin-D-SUB terminal) go out? TERMINAL_UNIT:

NO
Check the setting of an external input device that connects of CN554.

Is R/G/B/H/V signal sent to pin (1)/R, (2)/G, (3)/B, (14)/H, (13)/V of VGA (CN554)? MAIN_UNIT:

YES NO
Check the line between IC U400 and CN554.

Is R/G/B/H/V signal sent to pin (AE20)/R, (AE19)/G, (AD19)/B, (AC18)/H, (AB18)/V of IC U400?

YES
Refer to "The picture doesn't appear in all modes."

No picture on the display (13)


Does not the picture of the component video signal input to Component go out? TERMINAL_UNIT:

NO
Check the setting of an external input device that connects of CN552.

Is Component Y/Pb/Pr signal sent to pin (2)/Y, (4)/Pb, (6)/Pr of AV1(CN552) ? MAIN_UNIT:

YES NO
Check the line between IC U400 and CN552.

Is Component Y/Pb/Pr signal sent to pin (AE21)/Y, (AD22)/Pb, (AF22)/Pr of IC U400?

YES
Refer to "The picture doesn't appear in all modes."

2008-03-14

37

LC-32SH25E
< During external connection > No picture on the monitor (1)


No picture appears on SCART1 - connected monitor during the tuner (U/V) reception.


Checklist: 1) Is the Signal Type (item) in MENU-Option-Input Select equal to Signal Type of an external device? ...Set it to "CVBS", "Y/C", "RGB", "AUTO". 2) Is ANT-CABLE disconnected or connected improperly? ...Connect it correctly as per the operation manual. 3) The picture is sent to the monitor in a CVBS signal if the source during display is ATV, CVBS or Y/C of SCART1-2, AV3. When sent by component, etc., that signal is not sent to the monitor. 4) When the monitor picture is not sent and is not displayed on the monitor, refer to "No picture" for each terminal. 5) The video output from SCART1 is not the monitor output (output of the picture now watching). The picture of the last selected TV channel is always sent to SCART1. (Specification) TERMINAL_UNIT:

YES
Check the setting of an external input device that connects of CN500.

Is CVBS signal output into pin (19) of CN500 (SCART1)?

NO
Is TUNER_CVBS signal output into pin (21) of CN500 (SCART1)?

YES

Check the line between CN500 and TU200.

NO
Refer to "The picture doesn't appear in all modes."

< During external connection > No picture on the monitor (2) SCART2:



No picture from SCART1 appears on SCART2-connected monitor. NOTE: Normally, if the screen during display is sent to SCART2, no picture is sent to SCART2.


Checklist: 1) Is the Signal Type (item) in MENU-Option-Input Select equal to Signal Type of an external device? ...Set it to "CVBS", "Y/C", "AUTO". 2) The picture is sent to the monitor in a CVBS signal if the source during display is TV, CVBS or Y/C of SCART1-2, AV3. When sent by component, etc., that signal is not sent to the monitor. 3) When the monitor picture is not sent and is not displayed on the monitor, refer to "No picture" for each terminal. 4) The video output from SCART1 is not the monitor output (output of the picture now watching). The picture of the last selected TV channel is always sent to SCART1. (Specification) TERMINAL_UNIT:

YES
Check the setting of an external input device that connects of CN501.

Is CVBS signal output into pin (19) of CN501 (SCART2)?

NO
Is CVBS signal output from pin (A13) of IC U400 into pin (19) of CN501 (SCART2)?

YES

Check the line between CN501 and IC U400.

NO
Refer to "The picture doesn't appear in all modes."

38

LC-32SH25E

CHAPTER 5. MAJOR IC INFORMATIONS
[1] MAJOR IC INFORMATIONS
1. MAJOR IC INFORMATIONS
1.1. U400 (MT5362CHG/A)
GENERAL DESCRIPTION The MediaTek MT5362CHG/A family consists of a DTV(DVB-T) front-end demodulator, a backend decoder and a TV controller and offers high integration for advanced applications. It combines a transport de-multiplexer, a high definition video decoder, an AC3 audio decoder, an dual-link LVDS transmitter, and an NTSC/PAL/SECAM TV decoder with a 3D comb filter(NTSC/PAL). The MT5362CHG/A enables consumer electronics manufactures to build high quality, low cost and feature-rich DTV. World-Leading Audio/Video Technology: The MT5362CHG/A supports most Full-HD video decoder standards including H.264, MPEG4, MPEG2 and JPEG. The MT5362CHG/A also supports MediaTek MDDi
TM

de-interlace solution to reach very smooth picture quality for motions. A 3D comb filter added

to the TV decoder recovers great details for still pictures. The special color processing technology provides natural, deep colors and true studio quality video. Also, the MT5362CHG/A family has built-in high resolution and high-quality audio codec. Rich Features for High Value Products: The MT5362CHG/A family enables true single-chip experience. It integrates high-quality HDMI1.3, high speed VGA ADC, dual-channel LVDS, USB2.0 receiver and multi-media decoder Reliable DVB-T Receiving capability: MT5362CHG/A family supports DVB-T demodulation function. Excellent adjacent and co-channel rejection capability grants customers never miss any wonderful stream. Professional error-concealment provides stable, smooth and mosaic-free video quality. Key Features: 1. DVB-T demodulator 2. A transport demultiplexer 3. A multi-standard video decoder 4. An AC3/MPEG2 audio decoder 5. HDMI1.3 receiver 6. Audio codec Note: All packages are lead free General Feature List Host CPU · ARM 926EJS · 16K I-Cache and 16K D-Cache · 8K Instruction TCM · JTAG ICE interface · Watch Dog timers · Build-in CPI analyzer and Cache Hit Rate Meter Transport Demultiplexer · Supports a serial or parallel transport stream input · Supports ATSC, DVB, MPEG-2 transport stream input · Supports DES/3-DES/DVB/AES de-scramblers · Up to 8-PID even/odd keys for descrambling · Support 32 PID filters and 32 section filters · Support micro-processor section filtering · Support hardware CRC-32 check · Support PCR recovery function · Support a micro-processor for stream process and MPEG start code detection · Support DVB CA · Support simple trick play (Playback / Pause /Fast Forward (upto x32)) through USB or Flash MPEG2 Decoder · MPEG MP@ML, MP@HL and MPEG-1 video standards · Support de-blocking filter MPEG1 Decoder MPEG4.2 Decoder · ASP@15 (720P) H.264 (MPEG4.10) HD Decoder (AVC) · [email protected], [email protected], BP@L3 (baseline) video standard Still Image decoding · JPEG (base-line or progressive) De-mosquito engine · 2D/3D for all AV inputs 2D Graphics · Support multiple color modes

2008-03-14

· Point, horizontal/vertical line primitive drawings

39

LC-32SH25E
· Rectangle fill and gradient fill functions · Bitblt with transparent options · Alpha blending and alpha composition Bitblt · Stretch Bitblt · Font rendering by color expansion · YCbCr to RGB color space conversion Image Resizer · Support 2/4/8bpp index format, 16bpp/32bpp direct color format. · Support 420/422 video format. · Support 420/422/444 JPEG format. · Arbitrary ratio vertical/horizontal scaling of video, from 1/128X to 128X · Simple DMA. OSD Plane ·Two linking list OSDs with multiple color mode and one of them has scaler Video Plane · Support video capture and over scan. · Flesh tone management · Gamma correction · Color Transient Improvement (CTI) · 2D Peaking · Saturation/hue adjustment · Brightness and contrast adjustment · Black and White level extender · Adaptive Luma/Chroma management · Automatic detect film or video source · 3:2/2:2 pull down source detection · Support maximum 1920 width motion-adaptive de-interlace. · Support excellent low angle image processing. · Arbitrary ratio vertical/horizontal scaling of video, from 1/32X to 32X · Advanced non-linear panorama scaling. · Programmable zoom viewer · Progressive scan output · Support alpha blending · Dithering processing for flat panel display · Frame rate conversion. · Support FHD panel and VGA dot-to-dot · Support PIP/POP, (dual de-interlace, one HD and one SD) LVDS · Support 6/8/10-bit one ­ channel or 6/8-bit dual-channel LVDS transmitter, 2-link LVDS up-to 175 MHz · Built-in spread spectrum for EMI performance · Programmable panel timing output CVBS In · On-chip 54 MHz 10-bit video ADC · Support PAL (B,G,D,H,M,N,I,Nc), NTSC, · NTSC-4.43, SECAM · Macrovision detection · NTSC/PAL support 3D/2D comb filter · Built-in motion-adaptive 3D Noise Reduction · VBI data slicer for CC/TT decoding · Support 2-S-Video. · Max. Support 4-channel CVBS. · Support SCART connector VGA In · Support VGA input up to UXGA 162 MHz · Support full VESA standards Component Video In · Support two component video inputs · Support 480i / 480p / 576i / 576p / 720p / 1080i / 1080p Audio ADC · 2 channel on chip Audio ADC Audio digital input · 1 bit I2S audio input HDMI Receiver · HDMI1.3, data rate can be up to 2.25 GHz · EIA/CEA-861B · CEC

40

LC-32SH25E
Video bypass (for EU application) · TVbypass · CVBS Monitor (any AV input) TV audio demodulator

· Support BTSC / EIA-J / A2 / NICAM / PAL FM /
· SECAM world-wide formats · Standard automatic detection · Stereo demodulation, SAP demodulation · Mode selection (Main/SAP/Stereo) Audio DAC · 6 on-chip audio DACs (3-pair) support R/L channel and subwoofer outputs DRAM Controller · 32-bit DDR1/2 interface · Support 8MB to 128 MB DDR DRAM devices · Support DDR1-400, DDR1-500, DDR2-667 DDR2-800 Audio DSP · Support Dolby Digital AC-3 decoding (ATSC) · MPEG-1 layer I/II decoding (DVB) · Dolby Prologic II · Support WMA / HE-AAC / DTS / ADPCM / · LPCM · Audio output: 7.1ch + 2ch (down mix) · Pink noise and white noise generator · Equalizer · Bass management · 3D surround processing with virtual surround · Audio and video lip synchronization · Support reverberation · Automatic volume control · Support 5-bit (10-channel) main audio I S output interface: each of these channels is up to 24-bit resolution. · Support 1-bit (2-channel) aux audio I S output I/F: each of these channels is up to 24-bit resolution. S/PDIF interface · One SPDIF input · One SPDIF out Digital TV(DVB-T) Demodulator · COFDM(Coded Orthogonal Frequency Division Multiplex) channel demodulator for DVB-T receiver · ETSI 300 744 & Nordig Unified compliant · Excellent performance for SFN(Single Frequency Network) & Indoor reception · Support 2K, 8K modes · Support QPSK,16,64 QAM constellations · 1/4,1/8,1/16,1/32 Guard interval · Support hierarchical & non-hierarchical modes · Accept 6,7,8 MHz channel bandwidth · Automatic mode detection · Full-digital timing/frequency with wide acquisition range · Support triple offset · Excellent adjacent Channel interference (ACI) rejection capability · Excellent Co-Channel interference(CCI) rejection capability · Fast channel lock time Analog TV IF Demodulator · Support PAL/SECAM standard · Accept IF frequency at 38.25 MHz · Full digital AGC control and carrier recovery Peripherals · Each of the MT5362CHG/A has one built-in UART with Tx and Rx FIFO. It has hardware flow control and high speed data transferring. · The MT5362CHG/A family has three basic serial interfaces; one is for the tuner, one is the master for general purpose, the other is the slave for HDMI EDID data. · Three PWMs · While NAND Flash is disabled, the MT5362CHG/A support MS/MS-PRO, SD/MMC, and SDHC card reader. · IR blaster and receiver · Real-time clock and watchdog controller · The MT5362CHG/A includes 2-link USB2.0/1.1 (support external hub) for USB mass storage class device. · Built-in uP in standby module · SDIO interface (for DSG, WiFi or UWB) 2008-03-14 · Support two serial flash or one serial and one NAND · Support five-input low-speed ADC.
2 2

41

LC-32SH25E
· Support boundary scan (JTAG) IC Outline · MT5362CHG/A is 27x27 mm BGA Package · 3.3V/1.0V and 1.8V for DDR2

1.2. U103, U104 (L5985 VFQFPN8)
Description The L5985 is a step down switching regulator with 2.5A current limited embedded power MOSFET, so it is able to deliver up to 2A DC current to the load depending on the application condition. The input voltage can range from 2.9V to 18V, while the output voltage can be set starting from 0.6V to VIN. Having a minimum input voltage of 2.9V, the device is suitable for buses staring from for 3.3V bus. Requiring a minimum set of external components, the device includes an internal 250KHz switching frequency oscillator that can be externally adjusted up to 1MHz. The QFN package with exposed pad allows reducing the RthJA down to approximately 60°C/W. Features · 2A DC output current · 2.9V to 18V input voltage · Output voltage adjustable from 0.6V · 250KHz switching frequency, programmable up to 1MHz ·Internal Soft-start and Inhibit · Low dropout operation: 100% duty cycle · Voltage feed-forward · Zero load current operation · Over current and thermal protection · VQFN3x3-8L package Applications · Consumer: STB, DVD, DVD recorder, car audio, LCD TV and monitors · Industrial: Chargers, car battery, PLD, PLA, FPGA · Networking: XDSL, modems, DC-DC modules · Computer: Optical storage, hard disk drive, printers, audio/graphic cards

1.3. U351, U352 (HYB18TC512160B2F-25 TFBGA84)
Features The 512-Mbit Double-Data-Rate-Two SDRAM offers the following key features: · 1.8 V ± 0.1 V Power Supply · 1.8 V ± 0.1 V (SSTL_18) compatible I/O · DRAM organizations with 8, 16 data in/outputs · Double Data Rate architecture: - two data transfers per clock cycle - four internal banks for concurrent operation · Programmable CAS Latency: 3, 4, 5 and 6 · Programmable Burst Length: 4 and 8 · Differential clock inputs (CK and CK) · Bi-directional, differential data strobes (DQS and DQS) are transmitted / received with data. Edge aligned with read data and center-aligned with write data. · DLL aligns DQ and DQS transitions with clock · DQS can be disabled for single-ended data strobe operation · Commands entered on each positive clock edge, data and data mask are referenced to both edges of DQS · Data masks (DM) for write data · Posted CAS by programmable additive latency for better command and data bus efficiency · Off-Chip-Driver impedance adjustment (OCD) and On-Die-Termination (ODT) for better signal quality. · Auto-Precharge operation for read and write bursts · Auto-Refresh, Self-Refresh and power saving Power-Down modes · Average Refresh Period 7.8 µs at a TCASE lower than 85 °C, 3.9 µs between 85 °C and 95 °C · Programmable self refresh rate via EMRS2 setting · Programmable partial array refresh via EMRS2 settings · DCC enabling via EMRS2 setting · Full and reduced Strength Data-Output Drivers · 1K page size for x8, 2KB page size for x16 · Packages: PG-TFBGA-84, PG-TFBGA-60 · RoHS Compliant Products ) · All Speed grades faster than DDR2-400 comply with DDR2-400 timing specifications when run at a clock rate of 200 MHz.
1

42

LC-32SH25E
1.4. U600 (TDA8933BTW HTSSOP32)
General description The TDA8933B is a high-efficiency class D amplifier with low power dissipation. The continuous-time output power is 2 × 10 W in a stereo half-bridge application (RL = 8 ) or 1 × 20 W in a mono full-bridge application (RL =16 ). Due to the low power dissipation the device can be used without any external heat sink when playing music. Due to the implementation of thermal foldback(TF) the device remains operating with considerable music output power without the need for an external heat sink, even for high supply voltages and/or lower load impedances.

The device has two full differential inputs driving two independent outputs. It can be used in a mono full-bridge configuration (Bridge-Tied Load(BTL)) or as stereo half-bridge configuration (Single-Ended(SE)). Features · Operating voltage from 10 V to 36 V asymmetrical or ±5 V to ±18 V symmetrical · Mono bridge-tied load (full-bridge) or stereo single-ended (half-bridge) application · Application without heat sink using thermally enhanced small-outline package · High efficiency and low-power dissipation · Thermal foldback to avoid audio holes · Current limiting to avoid audio holes · Full short-circuit proof across load and to supply lines (using advanced current protection) · Switchable internal or external oscillator (master-slave setting) · No pop noise · Full differential inputs Applications · Flat-panel television sets · Flat-panel monitor sets · Multimedia systems · Wireless speakers · Mini/micro systems · Home sound sets

1.5. U602 (WM8521H9GED/RV SOIC-14)
DESCRIPTION The WM8521 is a 96kHz stereo DAC with an integrated output op-amp stage, designed to generate a 2.0Vrms output signal directly, so reducing external component requirements in digital audio applications. WM8521 comes into two variants WM8521HC and WM8521H9 which offers different line drive output capabilities. WM8521HC outputs 2Vrms at 12V supply, while WM8521H9 outputs 2.0Vrms at 9V supply. WM8521HC/H9 are designed for cost sensitive consumer digital audio applications requiring 2Vrms line output. A 24-bit multi-bit sigma delta DAC is used with oversampling digital interpolation filters. Digital audio input word lengths from 16-32 bits and sampling rates from 8kHz to 96kHz are supported. The audio interface supports I S, Right Justified and DSP digital audio formats. The devices are controlled via a hardware interface which provides access to features including de-emphasis, mute and data formats. These devices are pin equivalent and are available in a 14-pin SOIC package. FEATURES · Audio Performance - DAC SNR 98dB (`A' weighted @ 48kHz) - THD -81dB (`A' weighted @ 48kHz) · DAC Sampling Frequency: 8kHz ­ 96kHz · Pin Selectable Audio Data Interface Format - I S, 16-bit Right Justified or 16bit DSP · 2.0 Vrms output at 12V or 9V supply · 8.2V to 13.2V Analogue, 2.7V to 3.6 Digital Supply · 14-pin SOIC Package APPLICATIONS · Consumer digital audio applications requiring 2 Vrms output - DVD Players - Digital TV - Digital Set Top Boxes - A/V Receivers
2 2

2008-03-14

1.6. U401 (MT8295AE LQFP-128)

43

LC-32SH25E
FEATURES PCMCIA/CI Interface · Single slot PC Card interface · Single slot CI interface · 512 byte embedded buffer Host Interface · NAND flash interface · Interrupt capability · 3.3V logic levels Transport Stream Interface · MPEG2 compliant TS · One parallel or two serial TS interface from demodulator · Serial TS interface to MPEG2 decoder · Parallel TS interface from/to CAM · Supports serial to parallel TS conversion · Supports parallel to serial TS conversion Miscellaneous · 27 MHz crystal · 60 MHz clock input · Integrated PLL · 3.3/1.8V process · 5V compatible I/Os for PC Card interface · Supports additional 15 GPIOs · LQFP 128-pin package

1.7. U390 (MX25L3205DMI-12G SOP-16)
FEATURES GENERAL · Serial Peripheral Interface compatible -- Mode 0 and Mode 3 · 32M:33,554,432 x 1 bit structure or 16,772,216 x 2 bits (two I/O read mode) structure · 1024 Equal Sectors with 4K byte each (32Mb) - Any Sector can be erased individually · 64 Equal Blocks with 64K byte each (32Mb) - Any Block can be erased individually · Single Power Supply Operation - 2.7 to 3.6 volt for read, erase, and program operations · Latch-up protected to 100mA from -1V to Vcc +1V · Low Vcc write inhibit is from 1.5V to 2.5V PERFORMANCE · High Performance - Fast access time: 86MHz serial clock (15pF + 1TTL Load) and 66MHz serial clock (30pF + 1TTL Load) - Serial clock of two I/O read mode : 50MHz (15pF + TTL Load), which is equivalent to 100MHz - Fast program time: 1.4ms(typ.) and 5ms(max.)/page (256-byte per page) - Byte program time: 7us (typical) - Continuously program mode (automatically increase address under word program mode) - Fast erase time: 60ms(typ.) /sector (4K-byte per sector) ; 0.7s(typ.) /block (64K-byte per block); 25s(typ.) for 32Mb · Low Power Consumption - Low active read current: 25mA(max.) at 86MHz, 20mA(max.) at 66MHz and 10mA(max.) at 33MHz - Low active programming current: 20mA (max.) - Low active erase current: 20mA (max.) - Low standby current: 20uA (max.) - Deep power-down mode 1uA (typical) · Typical 100,000 erase/program cycles SOFTWARE FEATURES · Input Data Format - 1-byte Command code · Advanced Security Features - Block lock protection The BP0-BP3 status bit defines the size of the area to be software protection against program and erase instructions - Additional 512-bit secured OTP for unique identifier · Auto Erase and Auto Program Algorithm -