Text preview for : PANASONIC TX-L42G20E, TX-L42G20ES, TX-LF42G20S GLP25.pdf part of PANASONIC TX-L42G20E, TX-L42G20ES, TX-LF42G20S power TNP8EP103
Back to : PANASONIC TX-L42G20E, TX- | Home
ORDER No. PCZ1005063CE
Service Manual
Colour LCD Television
TX-L42G20E TX-L42G20ES TX-LF42G20S
GLP25 Chassis
Specifications
Power Source: 220-240V AC, 50Hz Rated Power Consumption: 188W Stand-by Power Consumption: 0.25W (Without monitor out recording) 17W (With monitor out recording) Aerial Impedance: Receiving System: 75 unbalanced, Coaxial Type PAL-I/H, B/G, D/K SECAM B/G, D/K, L/L' PAL-525/60 (AV only) DVB-T (Digital Terrestrial Services (MPEG2 and MPEG4-AVC(H.264)) DVB-C (Digital cable services (MPEG2 and MPEG4-AVC(H.264)) M.NTSC (AV only) NTSC (AV only) VGA, SVGA, WVGA, XGA, SXGA, WXGA (compressed) Horizontal scanning frequency 31 69 kHz Vertical scanning frequency 59 86 Hz VHF E2-E12 VHF A-H (ITALY) VHF R3-R5 UHF E21-E69 CATV S1-S10 (M1-M10) CATV S21-S41 (Hyperband) VHF H1-H2 (ITALY) VHF R1-R2 VHF R6-R12 CATV (S01-S05) CATV S11-S20 (U1-U10)
PC signals:
Receiving Chanels:
Aerial - Rear: Operating Conditions: Intermediate Frequency: Video/Audio Video Audio
VHF/UHF Temperature :0°C ÷ 35°C Humidity :20% ÷ 80% RH (non condensing)
Colour
38.9MHz, 33.9MHz 33.4MHz (B/G), 33.16MHz (A2) 33.05MHz (NICAM B/G, D/K, L') 32.4MHz (D/K), 32.66MHz (CZ STEREO) 40.4MHz (L'), 39.75MHz (L' NICAM) 34.47MHz (PAL) 34.5MHz, 34.65MHz (SECAM) 38.3MHz, 38.15MHz (SECAM L') © Panasonic Corporation 2010. Unauthorized copying and distribution is a violation of law.
Terminals: AV1 IN
Video (21 pin) Audio (21 pin) RGB (21 pin) Video (21 pin) Audio (21 pin) Video (21 pin) Audio (21 pin) RGB (21 pin) S-video IN (21-pin) Video (21 pin) Audio (21 pin) Audio (RCAx2) Video (RCAx1)
1V p-p 75 500mV rms 10k 0.7V p-p 75 1V p-p 75 500mV rms 1k 1V p-p 75 500mV rms 10k 0.7V p-p 75 Y: 1V p-p 75 C:0.3V p-p 75 1V p-p 75 500mV rms 1k 500mV rms 10k(used for HDMI4, AV3-AUDIO) Y:1V p-p 75
AV1 OUT AV2 IN
AV2 OUT
AV3 IN
HDMI1, HDMI2, HDMI3, HDMI4 Type A Connectors HDMI 1/3/4 :HDMI (Version 1.3a with Deep Colour) :HDMI (Version 1.4 with Content Type) HDMI 2 :HDMI (Version 1.4 with Content Type, Audio Return Channel) :HDMI (Version 1.3a with Deep Colour) This TV supports "HDAVI Control 5" function. COMPONENT AUDIO IN AUDIO OUT DIGITAL AUDIO OUT USB 1/2 CARD SLOT PC Video (RCAx3) Audio (RCAx2) Y:1V p-p 75 (including synchronization) Pb, Pr: ±0.35V p-p 75 500mV rms 10k (used for HDMI1/2/3, COMPONENT-AUDIO)
Audio (RCAx2) 500mV rms 1k (high impedance) PCM / Dolby digital,DTS, Fiber optic USB 2.0 DC 5V Max 500mA SD Card slot x1 Common Interface slot x1 HIGH-DENSITY D_SUB 15PIN R,G,B: 700mV p-p 75 HD,VD/TTL Level 2-5V p-p (high impedance)
ETHERNET LCD screen:
RJ45, IEEE802.3 10BASE-T / 100BASE-TX L5EDDAT00006 1,920 x 1,080 XGA, 16:9 Visible Diagonal 1060mm 20W (2x10W), 10% THD 3,5mm, 8 Impedance Remote Control Height: 682mm 637mm Width: 1021mm 1021mm 2 x R6 (UM3) Batteries Depth: 310mm 109mm
Audio Output: Headphones: Accessories supplied : Dimensions: Including TV stand TV set only Mass: Including TV stand TV set only
20.5kg 17.5kg
Specifications are subject to change without notice. Weights and dimensions shown are approximate.
Warning
This service information is designed for experienced repair technicians only and is not designed for use by the general public. It does not contain warnings or cautions to advise non-technical individuals of potencial dangers in attempting to service a product. Products powered by electricity should be serviced or repaired only by experienced professional technicians. Any attempt to service or repair the product or products deal within this service information by anyone else could result in serious injury or death.
2
CONTENTS
SAFETY PRECAUTIONS .......................................................................... 4 GENERAL GUIDE LINES..................................................................... 4 TOUCH CURRENT CHECK.............................................................. 4 PREVENTION OF ELECTROSTATIC DISCHARGE (ESD) TO ELECTROSTATICALLY SENSITIVE (ES) DEVICES .......................... 5 ABOUT LEAD FREE SOLDER (PBF)........................................................ 6 SUGGESTED PB FREE SOLDER....................................................... 6 APPLICABLE SIGNALS............................................................................. 7 SERVICE HINTS ....................................................................................... 8 CHASSIS BOARD LAYOUT ...................................................................... 9 AND LOCATION OF LEAD WIRING.................................................9 TECHNICAL DESCRIPTION.....................................................................10 SETTING INSPECTION........................................................................... 11 SELF-CHECK .......................................................................................... 12 POWER LED BLINKING TIMING CHART ............................................... 13 SERVICE MODE FUNCTION .................................................................. 14 SERVICE ................................................................................................ 15 SERVICE TOOL MODE........................................................................... 16 HOTEL MODE ......................................................................................... 17 DATA COPY BY SD CARD ..................................................................... 18 DATA COPY FROM TV SET TO SD CARD ............................................ 19 DATA COPY FROM TV SET TO TV SET................................................ 20 OPTION DESCRIPTION.......................................................................... 21 ADJUSTMENT METHOD ........................................................................ 22 WIRING DIAGRAM .................................................................................. 23 BLOCK DIAGRAMS................................................................................. 24 PARTS LOCATION.................................................................................. 27 REPLACEMENT PARTS LIST................................................................. 29 SCHEMATIC DIAGRAMS........................................................................ 47 A-BOARD (1 OF 23) SCHEMATIC DIAGRAM ................................... 48 P-BOARD (1 OF 2) SCHEMATIC DIAGRAM ..................................... 71 TC-BOARD (1 OF 6) SCHEMATIC DIAGRAM................................... 73 V-BOARD SCHEMATIC DIAGRAM ................................................... 79 CONDUCTOR VIEWS ............................................................................. 80
3
Safety Precautions
General Guide Lines
1. 2. 3. 4. When servicing, observe the original lead dress. If a short circuit is found, replace all parts which have been overheated or damaged by the short circuit. After servicing, see to it that all the protective devices such as insulation barriers, insulation papers shields are properly installed. After servicing, make the following touch current checks to prevent the customer from being exposed to shock hazards. Always ensure panel TKP0E16001 is correctly replaced before returning to customer (see Fig.1).
Fig. 1
Touch-Current Check
1. 2. 3. 4. 5. 6. Plug the AC cord directly into the AC outlet. Do not use an isolation transformer for this check. Connect a measuring network for touch currents between each exposed metallic part on the set and a good earth ground such as a water pipe, as shown in Fig. 2. Use Leakage Current Tester (Simpson 228 or equivalent) to measure the potential across the measuring network. Check each exposed metallic part, and measure the voltage at each point. Reserve the AC plug in the AC outlet and repeat each of the above measure. The potential at any point (TOUCH CURRENT) expressed as voltage U1 and U2, does not exceed the following values: For a. c.: U1 = 35 V (peak) and U2 = 0.35 V (peak); For d. c.: U1 = 1.0 V, Note: The limit value of U2 = 0.35 V (peak) for a. c. and U1 = 1.0 V for d. c. correspond to the values 0.7 mA (peak) a. c. and 2.0 mA d. c. The limit value U1 = 35 V (peak) for a. c. correspond to the value 70 mA (peak) a. c. for frequencies greater than 100 kHz. In case a measurement is out of the limits specified, there is a possibility of a shock hazard, and the equipment should be repaired and rechecked before it is returned to the customer.
7.
Measuring network for TOUCH CURRENTS
COLD WATER PIPE (EARTH GROUND) RS=1500 CS=0.22F 10k TO APPLIANCES EXPOSED METAL PARTS Resistance values in ohms () V: Voltmetr or oscilloscope (r.m.s. or peak reading) Input resistance: 1M Input capacitance: 200pF Frequency range: 15Hz to 1MHz and d.c.respectively
R0=500
U1
0.022F
V
U2 (V)
NOTE Appropriate measures should be taken to obtain the correct value in case of non-sinusoidal waveforms
Fig. 2
4
Prevention of Electrostatic Discharge (ESD) to Electrostatically Sensitive (ES) Devices
Some semiconductor (solid state) devices can be damaged easily by static electricity. Such components commonly are called Electrostatically Sensitive (ES) Devices. Examples of typical ES devices are integrated circuits and some field-effect transistors and semiconductor "chip" components. The following techniques should be used to help reduce the incidence of component damage caused by electrostatic discharge (ESD). 1. Immediately before handling any semiconductor component or semiconductor-equipped assembly, drain off any ESD on your body by touching a known earth ground. Alternatively, obtain and wear a commercially available discharging ESD wrist strap, which should be removed for potential shock reasons prior to applying power to the unit under test. After removing an electrical assembly equipped with ES devices, place the assembly on a conductive surface such as aluminum foil, to prevent electrostatic charge build up or exposure of the assembly. Use only a grounded-tip soldering iron to solder or unsolder ES devices. Use only an anti-static solder removal device. Some solder removal devices not classified as "anti-static (ESD protected)" can generate electrical charge sufficient to damage ES devices. Do not use freon-propelled chemicals. These can generate electrical charges sufficient to damage ES devices. Do not remove a replacement ES device from its protective package until immediately before you are ready to install it. (Most replacement ES devices are packaged with leads electrically shorted together by conductive foam, aluminum foil or comparable conductive material). Immediately before removing the protective material from the leads of a replacement ES device, touch the protective material to the chassis or circuit assembly into which the device will be installed. Caution Be sure no power is applied to the chassis or circuit, and observe all other safety precautions. Minimize bodily motions when handling unpackaged replacement ES devices. (Otherwise harmless motion such as the brushing together of your clothes fabric or the lifting of your foot from a carpeted floor can generate static electricity (ESD) sufficient to damage an ES device).
2. 3. 4. 5. 6.
7.
8.
IMPORTANT SAFETY NOTICE
There are special components used in this equipment which are important for safety. These parts are marked by in schematic diagrams, exploded views and replacement parts list. It is essential that these critical parts should be replaced with manufacturer's specified parts to prevent shock, fire, or other hazards. Do not modify the original design without permission of manufacturer.
5
About lead free solder (PbF)
Note: Lead is listed as (Pb) in the periodic table of elements. In the information below, Pb will refer to Lead solder, and PbF will refer to Lead Free Solder. The Lead Free Solder used in our manufacturing process and discussed below is (Sn+Ag+Cu). That is Tin (Sn), Silver (Ag) and Copper (Cu) although other types are available. This model uses Pb Free solder in it's manufacture due to environmental conservation issues. For service and repair work, we'd suggest the use of Pb free solder as well, although Pb solder may be used. PCBs manufactured using lead free solder will have the PbF within a leaf Symbol stamped on the back of PCB. Caution · Pb free solder has a higher melting point than standard solder. Typically the melting point is 50 ~ 70 °F (30~40°C) higher. Please use a high temperature soldering iron and set it to 700 ± 20 °F (370 ± 10 °C). · Pb free solder will tend to splash when heated too high (about 1100 °F or 600 °C). If you must use Pb solder, please completely remove all of the Pb free solder on the pins or solder area before applying Pb solder. If this is not practical, be sure to heat the Pb free solder until it melts, before applying Pb solder. · After applying PbF solder to double layered boards, please check the component side for excess solder which may flow onto the opposite side. (see Fig.3)
Fig.3
Suggested Pb free solder There are several kinds of Pb free solder available for purchase. This product uses Sn+Ag+Cu (tin, silver, copper) solder. However, Sn+Cu (tin, copper), Sn+Zn+Bi (tin, zinc, bismuth) solder can also be used. (see Fig.4)
Fig.4
6
Applicable Signals
Component (Y, Pb, Pr), HDMI Signal name 525 (480) / 60i 525 (480) / 60p 625 (576) / 50i 625 (576) / 50p 750 (720) / 60p 750 (720) / 50p 1,125 (1,080) / 60i 1,125 (1,080) / 50i 1,125 (1,080) / 60p 1,125 (1,080) / 50p 1,125 (1,080) / 24p COMPONENT * * * * * * * * HDMI * * * * * * * * * * *
PC (from D-sub 15P) Signal name 640 × 400 @70 Hz 640 × 480 @60 Hz 640 × 480 @75 Hz 800 × 600 @60 Hz 800 × 600 @75 Hz 800 × 600 @85 Hz 852 × 480 @60Hz 1,024 × 768 @60Hz 1,024 × 768 @70Hz 1,024 × 768 @75Hz 1,024 × 768 @85Hz 1,280 × 768 @60Hz 1,280 × 1,024 @60Hz 1,366 × 768 @60Hz Macintosh 13" (640 × 480) Macintosh 16" (832 × 624) Macintosh 21" (1,152 × 870)
Applicable input signal for PC is basically compatible to VESA standard timing. Horizontal frequency (kHz) 31.47 31.47 37.50 37.88 46.88 53.67 31.44 48.36 56.48 60.02 68.68 47.70 63.98 48.39 35.00 49.73 68.68 Vertical frequency (Hz) 70.07 59.94 75.00 60.32 75.00 85.06 59.89 60.00 70.07 75.03 85.00 60.00 60.02 60.04 66.67 74.55 75.06
PC (from HDMI terminal) Signal name 640 × 480 @60 Hz 750 (720) / 60p 1,125 (1,080) / 60p
Applicable input signal for PC is basically compatible to HDMI standard timing. Horizontal frequency (kHz) 31.47 45.00 67.50 Vertical frequency (Hz) 60.00 60.00 60.00
Note: · · · Signals other than above may not be displayed properly. The above signals are reformatted for optimal viewing on your display. PC signal is magnified or compressed for display, so that it may not be possible to show fine detail with sufficient clarity.
7
Service Hints
How to remove the backcover
Lay the main unit face down. (see Fig.5)
Fig.5
Remove the 4 fixing screws and the pedestal assembly. (see Fig.6)
SCREWS
Fig.6
Remove the 17 fixing screws. (see Fig.7)
SCREWS
SCREWS
Fig.7
8
Chassis Board Layout
TC-BOARD G-UNIT P-BOARD A-BOARD
V-BOARD
Board Name A-BOARD P-BOARD V-BOARD G-UNIT TC-BOARD
Function AV Terminal, HDMI, AV Switch, Sound Processor, TV tuner, PC, LAN, OPT Terminal, GENX, EEPROM, ADV,LDA2, Speaker out,USB slot Power Supply, Main Input Remote Receiver, C.A.T.S., R/G LED Side AV3 Terminal Panel Driver
Location of Lead Wiring
To find the Part Number of required wire in Replacement Parts List click on the wire name in red box.
P3-INV
P4-INV
A09-P2
TC01-PAN
TC04-PAN
A15-PAN
TC01
TC04
TC05
TC06
P4 P3 P2 A15
A09 CN0100 A12 P1
A02
A10
SP V10 SP
A02-S01
A10-V10
A12-SP
9
Technical Description
Specification of KEY for CI Plus, DTCP-IP and One-to-One General information:
1. EEPROM (IC8950) for spare parts has the seed of KEY for each. 2. The final KEY data will be generated by LDA2 IC (IC8000) when SELF CHECK was done and are stored in both LDA2 IC (IC8000) and EEPROM (IC8950). Three KEY are not generated for all models. The necessary KEY are only generated and stored depend on the feature of models.
Replacement of ICs:
When LDA2 IC (IC8000) is replaced, EEPROM (IC8950) should be also replaced with new one the same time. When EEPROM (IC8950) is replaced, LDA2 IC (IC8000) is not necessary to be replaced the same time. After the replacement of IC, SELF CHECK should be done to generate the final KEY data. How to SELF CHECK: While pressing [VOLUME ( - )] button on the main unit, press [MENU] button on the remote control for more than 3 seconds. TV will be forced to the factory shipment setting after this SELF CHECK.
Model and Keys:
Keys Model No. TX-L42G20E TX-L42G20ES TX-LF42G20S CI PLUS YES YES None DTCP-IP YES YES YES One-to_one (for USB Rec.) YES YES YES
10
Setting Inspection
Voltage Confirmation
A board Description SUB1.8V SUB1.2V SUB3.3V SUB5V SUB9V STB5V TC board Description ZW1.2V ZW3.3V LVCORE1.2V LVCC3.3V LVDD16V VGH(25oC) VGL H_VDD8V P board Description 24V_INV 17V 12V STB_5V8/TUNER5V8 400V Test point TP807 TP806 TP805 TP803 TP800 Voltage < 1V < 1V < 0.5V 5.7V ± 0.3V n/a Test point TP5601 TP5600 TP5602 TP5200 TP5220 TP5400 Voltage 1.76V 1.87V 1.18V 1.29V 3.19V 3.39V 4.9V 5.1V 8.82V 9.27V 4.9V 5.1V
Test point TP9061 TP9062 TP9205 TP9208 TP9210 TP9211 TP9207 TP9206
Voltage 1.17 - 1.31V 3.1 - 3.5V 1.10 - 1.25V 3.1 - 3.5V 15.75 - 16.94V 26.69 - 28.69V -5.67 - -4.93V 7.89 - 8.41V
11
Self Check
Self-check is used to automatically check the bus lines and hexadecimal code of the TV set. To enter Self-Check mode, keep pressing the down (-/v) button on the TV set and press the STATUS button on the remote control. To exit Self Check, switch off the TV set at the power button.
42FHD
TX-L42G20E
TUN STBY MEM1 MEM2 ADAM AVSW OFDM VIF LAN ZWEI ID O.K. O.K. O.K. O.K. O.K. O.K. O.K. O.K. O.K. O.K. O.K.
Panasonic 2010LCD Self Check Complete PEAKS-SOFT PEAKS-EEP LSI-PACKAGE LSI-RELEASE STBY-SOFT STBY-EEP STBY-ROMCORR ZWEI-SOFT 2.005 01.00.0005 0.024 0.29 1.00.00 1.08.3600 1.01.00 05000102 SUM C71D
MODEL ID
07 03087100 00000020
EDID
53 0afaeada
42FHD
TX-L42G20ES
TUN STBY MEM1 MEM2 ADAM AVSW OFDM VIF LAN ZWEI ID O.K. O.K. O.K. O.K. O.K. O.K. O.K. O.K. O.K. O.K. O.K.
Panasonic 2010LCD Self Check Complete PEAKS-SOFT PEAKS-EEP LSI-PACKAGE LSI-RELEASE STBY-SOFT STBY-EEP STBY-ROMCORR ZWEI-SOFT 2.005 01.00.0005 0.024 0.29 1.00.00 1.08.3600 1.01.00 05000102 SUM C71D
MODEL ID
07 03087100 00000020
EDID
53 0afaeada
42FHD
TX-LF42G20S
TUN STBY MEM1 MEM2 ADAM AVSW OFDM VIF LAN ZWEI ID O.K. O.K. O.K. O.K. O.K. O.K. O.K. O.K. O.K. O.K. O.K.
Panasonic 2010LCD Self Check Complete PEAKS-SOFT PEAKS-EEP LSI-PACKAGE LSI-RELEASE STBY-SOFT STBY-EEP STBY-ROMCORR ZWEI-SOFT 2.005 01.00.0006 0.024 0.29 1.00.00 1.08.3600 1.01.00 05000102 SUM C7BE
MODEL ID
07 03A87100 00000020
EDID
53 0afaeada
Display TUN STBY MEM1 MEM2 ADAM AVSW OFDM VIF LAN ZWEI ID
Ref. No. TU2901 IC1100 IC1101 IC8950 IC8000 IC3000 IC8300 TU2901 IC8703 IC9006 IC8950
Description TUNER GENX EEPROM GENX EEPROM LDA2 A CHIP LDA2 AUDIO VIDEO SWITCH DIGITAL DEMODULATOR TUNER ETHERNET IF ZWEI EEPROM(LDA2)
P.C.B. A-Board A-Board A-Board A-Board A-Board A-Board A-Board A-Board A-Board TC-Board A-Board
If the CCU ports have been checked and found to be incorrect or not located then " - - " will appear in place of "O.K.".
12
Power LED blinking timing chart
1. Subject Information of LED Flashing timing chart. Contents When abnormality has occurred the unit, the protection circuit operates and reset to the stand by mode. At this time, the defective block can be identified by number of blinking of the Power LED on the front panel of the unit.
2.
Blinking times
Once
Blinking timing
4 sec Light No Light
Contents BL_SOS (BACKLIGHT SOS)
Check point LCD PANEL A BOARD
1
2
FAN_SOS
A BOARD
3
SOS
A BOARD A BOARD P BOARD
4
SUB12V_SENSE_SOS
7
SUB3.3V_SENSE_SOS
A BOARD
9
SOUND_SOS
A BOARD P UNIT
10
ZWEI
TC BOARD
13
EMERGENCY SOS
A BOARD
13
Service Mode Function
MPU controls the functions switching for each IICs through IIC bus in this chassis. The following setting and adjustment can be adjusted by remote control in Service Menu
How to enter SERVICE
While pressing (-/v) button on TV unit, press control for 3 times within 2 seconds. Note: To exit from Service mode, press the exit button on remote control. 0 on the remote
14
SERVICE
SERVICE ADJUST WB-ADJ OPTION SRV-TOOL Peaks SOFT 2.005 Peaks EEP 01.00.0005 LSI PACKAGE 0.024 LSI DATA 0.02.09 STBY SOFT 1.00.00 STBY EEP 1.08.3600 STBY ROMCOR 1.01.00 ZWEI SOFT 5.01.0002 Ajax_CE 0.8.6 OPTION 1 OPTION 2 OPTION 3 OPTION 4 Model ID 1c ee 01 08 07 03087100 00000020 000/000 0000 L0.403
Key Command
· · · · Press the 3/4 button to change the adjustment values or function. Press the 1/2 button to step up/down through the functions and adjustments Press the numerical button VOLUME (+/-) to change option item. Press the OK button after each adjustment has been made to store the required values.
R/E Cnt INV Cnt CMS data
1
2
ADJUST CONTRAST YMAX
DYNAMIC 000
3
ADJUST COLOR
DYNAMIC 3C
3
ADJUST TINT
DYNAMIC 00
3
ADJUST SUB-BRT
DYNAMIC 800
3
ADJUST BACKLIGHT
DYNAMIC 554
3
ADJUST H-POS
DYNAMIC 0
3
ADJUST H-AMP
DYNAMIC 0
3
ADJUST V-POS
DYNAMIC 0
3
ADJUST V-AMP
DYNAMIC 0
1,2:MAIN SELECT 3,4:SUB SELECT 9 :PICTURE MENU SELECT YELLOW:AUTO ADJUST VOL:ADJUST OK :WRITE
4
1,2:MAIN SELECT 3,4:SUB SELECT 9 :PICTURE MENU SELECT VOL:ADJUST OK :WRITE
4
1,2:MAIN SELECT 3,4:SUB SELECT 9 :PICTURE MENU SELECT VOL:ADJUST OK :WRITE
4
1,2:MAIN SELECT 3,4:SUB SELECT 9 :PICTURE MENU SELECT VOL:ADJUST OK :WRITE
4
1,2:MAIN SELECT 3,4:SUB SELECT 9 :PICTURE MENU SELECT VOL:ADJUST OK :WRITE
4
1,2:MAIN SELECT 3,4:SUB SELECT 9 :PICTURE MENU SELECT VOL:ADJUST OK :WRITE
4
1,2:MAIN SELECT 3,4:SUB SELECT 9 :PICTURE MENU SELECT VOL:ADJUST OK :WRITE
4
1,2:MAIN SELECT 3,4:SUB SELECT 9 :PICTURE MENU SELECT VOL:ADJUST OK :WRITE
4
1,2:MAIN SELECT 3,4:SUB SELECT 9 :PICTURE MENU SELECT VOL:ADJUST OK :WRITE
4 1 2
ADJUST VCOM BEFORE WB-ADJ G-GAIN BEFORE DYNAMIC FF FF 02 NORMAL WB-ADJ B-GAIN BEFORE DYNAMIC E8 E8 02 NORMAL WB-ADJ R-CENT BEFORE DYNAMIC 93 93 02 NORMAL WB-ADJ G-CENT BEFORE DYNAMIC 80 80 02 NORMAL WB-ADJ B-CENT BEFORE DYNAMIC 9B 9B 02 NORMAL
3
DYNAMIC 154 154
WB-ADJ R-GAIN BEFORE
DYNAMIC FF FF 02 NORMAL
3
3
3
3
3
METHOD COLOR TEMP
METHOD COLOR TEMP
METHOD COLOR TEMP
METHOD COLOR TEMP
METHOD COLOR TEMP
METHOD COLOR TEMP
1,2:MAIN SELECT 3,4:SUB SELECT 7 :COLOR TEMP SELECT 9 :PICTURE MENU SELECT 0 :WB METHOD SELECT VOL:ADJUST OK :WRITE/WB DIFF ADJ
4
1,2:MAIN SELECT 3,4:SUB SELECT 7 :COLOR TEMP SELECT 9 :PICTURE MENU SELECT 0 :WB METHOD SELECT VOL:ADJUST OK :WRITE/WB DIFF ADJ
4
1,2:MAIN SELECT 3,4:SUB SELECT 7 :COLOR TEMP SELECT 9 :PICTURE MENU SELECT 0 :WB METHOD SELECT VOL:ADJUST OK :WRITE/WB DIFF ADJ
4
1,2:MAIN SELECT 3,4:SUB SELECT 7 :COLOR TEMP SELECT 9 :PICTURE MENU SELECT 0 :WB METHOD SELECT VOL:ADJUST OK :WRITE/WB DIFF ADJ
4
1,2:MAIN SELECT 3,4:SUB SELECT 7 :COLOR TEMP SELECT 9 :PICTURE MENU SELECT 0 :WB METHOD SELECT VOL:ADJUST OK :WRITE/WB DIFF ADJ
4
1,2:MAIN SELECT 3,4:SUB SELECT 7 :COLOR TEMP SELECT 9 :PICTURE MENU SELECT 0 :WB METHOD SELECT VOL:ADJUST OK :WRITE/WB DIFF ADJ
1,2:MAIN SELECT 3,4:SUB SELECT 5 :FLICKER PATTERN 9 :PICTURE MENU SELECT VOL:ADJUST OK :WRITE
1
2
OPTION Boot
DYNAMIC ROM
3
OPTION STBY-SET
DYNAMIC 00
3
OPTION Emergency
DYNAMIC ON
3
OPTION Y/C Delay
DYNAMIC
3
OPTION OPT 1
DYNAMIC 00001100
3
OPTION OPT 2
DYNAMIC 11101110
3
OPTION OPT 3
DYNAMIC 00000001
3
OPTION OPT 4
DYNAMIC 00100000
3
OPTION EDID-CLK HDMI
DYNAMIC MID 1
1,2:MAIN SELECT 3,4:SUB SELECT 9 :PICTURE MENU SELECT VOL:ADJUST
4
1,2:MAIN SELECT 3,4:SUB SELECT 9 :PICTURE MENU SELECT OK :POWER OFF
4
1,2:MAIN SELECT 3,4:SUB SELECT 9 :PICTURE MENU SELECT VOL:ADJUST
4
1,2:MAIN SELECT 3,4:SUB SELECT 9 :PICTURE MENU SELECT VOL:ADJUST OK :WRITE
4
1,2:MAIN SELECT 3,4:SUB SELECT 5,6:BIT SELECT 9 :PICTURE MENU SELECT VOL:ADJUST OK :WRITE
4
1,2:MAIN SELECT 3,4:SUB SELECT 5,6:BIT SELECT 9 :PICTURE MENU SELECT VOL:ADJUST OK :WRITE
4
1,2:MAIN SELECT 3,4:SUB SELECT 5,6:BIT SELECT 9 :PICTURE MENU SELECT VOL:ADJUST OK :WRITE
4
1,2:MAIN SELECT 3,4:SUB SELECT 5,6:BIT SELECT 9 :PICTURE MENU SELECT VOL:ADJUST OK :WRITE
4
1,2:MAIN SELECT 3,4:SUB SELECT 7 :HDMI SELECT 9 :PICTURE MENU SELECT VOL:ADJUST OK :WRITE
1
2
SRV-TOOL
DYNAMIC 00
1,2:MAIN SELECT 9 :PICTURE MENU SELECT OK :ENTER
15
Service Tool Mode
How to access
1. 2. Select [SRV-TOOL] in Service Mode. Press [OK] button on the remote control.
SRV-TOOL
Display of TD2Microcode version Display of Flash ROM maker code Display of SOS History
TD2Microcode:005a0910 Flash ROOM: AD F1 PTCT:00.00.00.00.00
Time 00051:30
On/Off 0000042
POWER ON TIME/COUNT Press [MUTE] button (3sec)
Display of SOS History
SOS History (Number of LED blinking) indication. nd st From left side; Last SOS, before Last, three occurrence before, 2 occurrence after shipment, 1 occurrence after shipment. This indication will be cleared by [Self/check indication and forced to factory shipment setting].
Power ON Time, On/Off
Note: To display TIME/COUNT menu, highlight position, then press MUTE for 3sec. Time: Cumulative power on time, indicated hour: minute by decimal. On/Off: Number of On/Off switching by decimal. Note: This indication will not be cleared by either of the self-checks or any other command.
Exit
Disconnect the AC cord from wall outlet or switch off the power with [Power] button on the main unit.
16
Hotel Mode
1. Purpose Restrict a function for hotels. 2. Access command to the Hotel mode setup menu. In order to display the Hotel mode setup menu, please enter the following command (within 2 second). [TV] : Vol.[Down] + [REMOTE] : AV (3 times) Then, the Hotel mode setup menu is displayed.
ITEM Hotel Mode Initial INPUT Function Select hotel mode ON/OFF Select input signal modes. Set the input, when each time power is switched on. Selection: Off Analog /DVB-C/DVB-T AV1/AV2/AV2S/AV3/ Component/HDMI1/HDMI2/HDMI3/HDMI4 *Off: give priority to the last memory. However, Euro Model is compulsorily set to TV. *AVnS/AVnC: only Euro model selectable * PC:selectable with VGA option Select programme number. Selection: Off/0 to 99 *Off: give priority to the last memory Adjust the volume when each time power is switched on. Selection/Range: Off/0 to 100 *Off: give priority to the last memory Adjust maximum volume. Range: 0 to 100 Select local key conditions. Selection: Off/SETUP/MENU/ALL *Off: altogether valid *Setup: only F-key is invalid (Tuning guide (menu) can not be selected.) *MENU: only F-key is invalid (only Volume/Mute can be selected.) *All: altogether invalid. Select remote control key conditions. Selection: Off/SETUP/MENU *Off: altogether valid *Setup: only Setup menu is invalid MENU: Picture/Sound/Setup menu are invalid
Hotel mode Hotel mode Initial INPUT Initial POS Initial VOL Level Maximum Vol Level Button Lock Remote Lock Select
EXIT Change RETURN
Off Off Off Off Off Off Off
Initial POS
Initial VOL Level
Maximum VOL Level Button Lock
3. To exit the "Hotel mode" menu press the EXIT button on remote control. 4. Explain the Hotel mode setup menu.
Remote Lock
17
Data Copy by SD Card
Purpose a) Board replacement (Copy the data when exchanging A-board):
When exchanging A-board, the data in original A-board can be copied to SD card and then copy to new A-board.
TV
(Before exchanging) Copy to SD card SD (After exchanging) Copy back from SD card
A-board
Following data can be copied. User setting data (inc. Hotel mode setting data) Channel scan data Adjustment and factory preset data
b) Hotel (Copy the data when installing a number of units in hotel or any facility):
When installing a number of units in hotel or any facility, the data in master TV can be copied to SD card and the copy to other TVs.
Master TV SD Copy to SD card
Other TV
Other TV
Other TV
Following data can be copied. User setting data (inc. Hotel mode setting data) Channel scan data
Copy from SD card
Preparation
Make pwd file as startup file for (a) or (b) in an empty SD card. 1. Insert an empty SD card to your PC. 2. Right-click a blank area in a SD card window, point to New, and then click text document. A new file is created by default (New Text Document.txt). 3. Right-click the new text document that you just created and select rename, and then change the name and extension of the file to the following file name (a) or (b) and press ENTER. File name: (a) For Board replacement: boardreplace.pwd (b) For Hotel: hotel.pwd Note: Please make only one file to prevent the operation error. No any other file should be in SD card.
18
Data Copy from TV set to SD Card
1. 2. 3. Turn on the TV set. Insert SD card with a startup file (pwd file) to SD slot. On-screen Display will be appeared according to the startup file automatically. Input a following password for (a) or (b) by using remote control. (a) For Board replacement: 2770 (b) For Hotel: 4850 Data will be copied from TV set to SD card. It takes around 2 to 6 minutes maximum for copying. After the completion of copying to SD card, remove SD card from TV set. Turn off the TV set.
4. 5.
Note: Following new folder will be created in SD card for data from TV set. (a) For Board replacement: user_setup (b) For Hotel: hotel
Data Copy(Board replacement )
Data copy (Board replacement) or (Hotel)
Input password -----
Data Copy(Board replacement )
Input Password 2770 or 4850
Input password -----
Data Copy(Board replacement ) Copy TV to SD card Please wait for a while Please do not remove the SD card
Performing
GETTING
Data Copy(Board replacement ) Performing
Data copy has been successful Please remove SD card
Completion
FINISH
19
Data Copy from SD Card to TV set
1. 2. 3. Turn on the TV set. Insert SD card with Data to SD slot. On-screen Display will be appeared according to the Data folder automatically. Input a following password for (a) or (b) by using remote control. (a) For Board replacement: 2771 (b) For Hotel: 4851 Data will be copied from SD card to TV set. After the completion of copying from SD card, remove SD card from TV set. (a) For Board replacement: Data will be deleted after copying (Limited one copy). (b) For Hotel: Data will not be deleted and can be used for other TVs. Turn off the TV set.
4.
5. Note: 1. 2.
Depending on the failure of boards, function of Data for board replacement does not work. This function can be effective among the same model numbers.
Input Data Copy(Board replacement ) Password Input Password 2771 or 4851
Input password Performing -----
Data Copy(Board replacement ) Copy SD card to TV Please wait for a while Please do not remove the SD card
Performing
WRITING
Data Copy(Board replacement ) Performing
Data copy has been successful Please remove SD card
Completion
FINISH
20
Option Bytes Description
OPTION1 b0 b1 b2 b3 b4 b5 b6 b7 OPTION2 b0 b1 b2 b3 b4 b5 b6 b7 OPTION3 b0 b1 b2 b3 b4 b5 b6 b7 OPTION4 b0 b1 b2 b3 b4 b5 b6 b7 ATP Search Speed TXT Ch Refresh ID-1 Macrovision Auto-Judge Surround enable low bit (*1) Surround enable low bit (*1) Pre Emphasis TINT_COMPONENT_HDMI Adjust lgain enable A2 BC enable (5.5) A2 DK1 enable (6.26) A2 DK3 enable (5.742) NICAM scan NICAM BG enable (5.5) NICAM I enable (6.0) NICAM DK enable (6.5) NICAM priority Starhub scan enable add H264 enable A2 DK2 enable Inhibition of countermeasure for SIF signal drop get onid from physical CH SASO mute All country DVB-S enable All country DVB-C enable 3DYC color motion detected Slow (1) / Fast (0) On (1) / Off (0) On (1) / Off (0) On (1) / Off (0) On (1) / Off (0) On (1) / Off (0) On (1) / Off (0) On (1) / Off (0) On (1) / Off (0) On (1) / Off (0) On (1) / Off (0) On (1) / Off (0) On (1) / Off (0) On (1) / Off (0) On (1) / Off (0) On (1) / Off (0) On (1) / Off (0) On (1) / Off (0) On (1) / Off (0) On (1) / Off (0) On (1) / Off (0) On (1) / Off (0) On (1) / Off (0) On (1) / Off (0) On (1) / Off (0) On (1) / Off (0) On (1) / Off (0) On (1) / Off (0) On (1) / Off (0) On (1) / Off (0) On (0) / Off (1)
PIP RF remote control
21
Adjustment Method
Sub-Contrast/White Balance Adjustment
1. 2. 3. 4. Instrument Name Remote controller LCD WB meter (Minolta CS-1000A equivalent) Comunication jig Computer for external control Procedure Connect to Remarks Correlation can be also taken by CA-210 or equivalent
Remarks Let the panel standfor more than 3 hours at more than 20 °C. Basically perform adjustment in the ambient environment of room temperature more than 20 °C. The aging time is more than20 min at above room temperature. Applied signal
Subcontrast adjustment 1. Receive PAL colour bar (100% white) RF signal. 2. Enter "Contrast" adj. In SERVICE mode. 3. Start adjusting by using Yellow Key. 4. If the adjustment finished normally, the letter of Contrast will change from red to black
100% full colour bar 0.7V p-p white peak 87.5% modulation
White Balance adjustment 1. Procedure basically performs checking using the production software and make automatic adjustment using external computer. 2. It adjusts in the mode of : Colour balance Normal as follows. Viewing Mode Dynamic
WHITE
Normal x: 0.2940 ± 0,010 y: 0.3140 ± 0,010 Normal x: 0.2940 ± 0,010 y: 0.3140 ± 0,010
100% WHITE
GRAY
50% GRAY
22
ETHERNET JK8401 CN0100 JK8850 D3300 JK8700 JK8701
Y,PB,PR AUDIO IN, AUDIO OUT CI SLOT SERVICE SD SLOT DIGITAL AUDIO OUT USB1 USB0
JK8800
JK3301
A04 G04
G-UNIT
JK3700 AV3
PC
JK3304
Wiring Diagram
AV1
JK3302
AV2
JK3303
A-BOARD
JK4700 JK4701 JK4703 JK4702 HDMI1 HDMI2 HDMI3 HDMI4
TUNER TU2901A
KEY
A02
SP
A12
LCD PANEL
A10
A09
A15
23
V10 P2 TC06
TC05 TC01
T-CON
TC04
V-BOARD
P-BOARD
P3
P4
P1
MAIN IN
Block Diagram (1/3)
JK8401 CI SLOT
SUB CI 5V
JK8700 USB1
JK8701 USB0
(C1AB00003188) OFDM IFD1/2
IC8300
TUNER DVB-T/C
TU2901A
2 10 15
IFD1/2 19,20 SIF-OUT 9 VIDEO OUT 11
TNR5V FE 1.2V SUB3.3V IFD1/2 SIF MAIN RF CVBS
37,38 32,40
2.5V
30,42,7 19 SUB3.3V
28,32,44 22,10 FE 1.2V
(C1AB00003193) CI TS ASIC 64,15 24,37 49
IC8400
(C1AB00002913) LEVEL SHIFER ASIC 49 2,17,33
IC8401
(C0DBZYY00266)
POWER SUPPLY 2,3
IC8701
(C0DBZYY00266)
POWER SUPPLY 2,3
IC8700
USB DATA
HS DATA
SUB3.3V
SUB5V
SUB3.3V
(C1AB00003218) AVSW
AV1 21PIN SCART
AV1_VOUT 19 AV1_RED 15
AV1_V 20
79 CVBSIN6 44 CVBS/Y +COUT3
SUB 1.2V D
SUB3.3V
SUB3.3V
5 CVBSin4
SUB5V
IC3000
JK3302
8 SUB 1.5V D SUB 3.3V VDDSD IIC1 EEP
AV1_GREEN 11 AV1_L 6
AV1_BLUE 7 AV1_LOUT 3
23 CVBS_IN2
IIC2 SDA/SCL 46-47
AV2 21PIN SCART
AV2_VOUT 19 AV2_RED/C 15 AV2_GREEN 11 AV2_L 6
AV2_V 20
AV2_BLUE 7 AV2_LOUT 3
19 G1/YIN1 38 Y/Y+C/CVBSOUT4 37 SAG CVBSOUT4 11 R2/CIN3 21 B1 CIN1 13 G2/YIN2 15 B2/CIN2 64 L4IN 54 L2OUT 65 R4IN 53 R2OUT
PC-R PC-G PC-B YPBPR-Y YPBPR-PB YPBPR-PR AUDIO L IN
SIF
G/CY/CVBSout1 31 B/PB/Cout1 33 R/PRout1 35 CVBSout 46 HDout 32 CVBSin1 17 R4out 49 L4out 50 L1IN 58 R1IN 59 L2IN 60 R2IN 61 VDout 34
SIF INN SIF INP
B9 A9 A4 A5 A6 A7 P1 P2 E18 C15 A15 B13 A13 D13 C13 POWER SUPPLY D-CHIP LVDS I/F SUB 3.3V SUB 1.2V D SUB 1.5V D VDDSD DDR1.5V
JK3303
LVDS RGB 10bit
MAIN Y/CVBS MAIN PB/C MAIN PR RGB CVBS PC VS PC HS DVB CVBS AV - R AV - L AUDIOOUT L AUDIOOUT R TV OUT L TV OUT R
37-40 32,33,35 36,30-27 24-21 16,17,19 20,14-11
AV2_ROUT 1
AV2_R 2
(MN2WS0110C) LDA02
AV / IO
AUDIO OUT F20 E19 C19 B19 D20 OPT AUDIO OUT SERIAL I/F SDA/SCL MAIN SND 17V 8 9 14 15 MAIN SND 17V
IC8000
A12
25-26 30-31 4 3
JK3304
1
3 RIN 2 GIN 1 BIN 95 CYIN1 93 PBIN1 97 PRIN1 70 L7IN 71 R7IN 52 L3OUT 51 R3OUT
PC
2 3
AUDIO AMP
(C1AB00003230) 36-37 41-42 2 1
IC2301
AUDIO OUT IN Y,PB,PR
Y PB PR L R L R
JK3301
HP_LOUT HP_ROUT
SERIAL COMMUNICATION
B14 A14
HDMI
ETHER PHY
A-Chip
D-Chip
(C0DBGYY00895) REG 1 DATA
IC5220
3
SUB F12V 15V SUB 9V
A04 TO G-UNIT
6 4 2 3 1
STB SUB8.8V
AV3_RIN HP_LOUT HP_ROUT
SUBF12_15V
SUB OP 5V
OVP DET
AV3_LIN
P17V
IIC1
AV3_VIN
81 CVBS IN5 68 L6IN 69 R6IN
OVP Circuit
STB XRST
SUB F12V 15V SUB OP 5V
2 REG 3 (C0DBAYY00755) 1 8 4 5
IC5300
ADJ SCL/SDA
IC5000 IC4701
4 PWM9V SUB_F12V_15V
HDMI 5V DET0,1,2,3 (AN34042A-VF)
(C0DBAYY00715) STB 5.8V P17V SUBF12 15V DCDCIN STB SUB 5.8V 5.8VS DCDCIN DCDCIN
3
TO P-BOARD
DDC0,1,2,3
9 9-10 10 12
13 13 12
STB 3.3V
STB3.3V
SUB 5V
20
SUB3.3V
HPD1 HDMI_5V_DET1
STB 5V
2 1
5.8VS KEYSCAN
STB-5.8V
SDA/SCL
SUB3.3V
SUB3.3V
SUB F12V 15V
STB 5V
Q5241
PNL 12V
SUB3.3V
ON/OFF
HDMI 5V DET1 ARC
ALARM
HPD2 HDMI_5V_DET2
HDMI_5V_DET0
ARC SWITCH OPT SPDIF
GenX8 E2PROM
5 4
SUB ON MAIN ON
P17V
R5266 R5265
MAIN SND 17V
(C0DBGYY00281) STB 5.8V
IC5280
4
3
5.8VS
STB5V
4 9
SUB1.5V
TNR 5V
HDMI CEC
HPD0,1,2,3
SUB3.3V
(C0DBAYY00715)
IC5501
STB SUB 5.8V
(C0DBGYY00281) REG
IC2952
SG GENX KEY1
7 7
STB 3.3V
SUB3.3V
3
20
4 9
SUB1.2V_A SUB1.2V_D
SUB 5V STB SUB 5.8V
REG (C0DBEYY00124)
IC5200
HDMI SWITCH (C1AB00003079) 3.3V HDMI
(C0DBGYY00578) REG
AI SENSOR 24,39,62 88,68,64 IIC1 EEP 8 25,26 9-12 G LED R LED
5 3 2
5
SUB5V STB3.3V
8 4
DDC1
CEC HPD1
DDC1
DDC0
DDC2
CEC
CEC
CEC HPD0
A02
HDMI2
HDMI1
HDMI3
HDMI4
D3300
1
2
3
SD CARD
JK4701
JK4700
JK4703
JK4702
24
DIGITAL AUDIO OUT
TO K BOARD
JK8850
SERVICE FOR ADJUSTMENT
ETHERNET LAN
CN0100
JK8800
RX/TX
TO V-BOARD
A09
IC5500
IC4700
Analog ASIC
IC1100
(MNZSFH9GP91)
EEP WP IIC1
GenX8
(C3EBFC000047)
EEPROM
IC1101
(C1CB00003239)
ETHERNET
IC8703
A10
REMOTE 6
TO TC-BOARD SP- R SP- L
AV1_ROUT 1
AV1_R 2
91 PRIN2/R3 89 CYIN2/G3 87 PBIN2/B3 62 L3IN 56 L1OUT 63 R3_IN 55 R1_OUT
(C3EBJC000055) EEPROM LDA2
IC8950
IC8240,IC8241
DDR3 2x 1Gbit
12,37
(C3FBTY000011) NAND FLASH
IC8921
(C0DBGYY00281) REG 1
IC2952
4
STB SUB5.8V TNR 5V SUB3.3V FE1.2V PNL 12V
USB DATA
IC8302 (C0DBFYY00041)
SUB 0P 5V
SUB 0P 5V
POWER SUPPLY A-CHIP
IIC /IF (HSDATA)
DDR3 I/F
EXTERNAL BUS
TS IF
CPU BUS
HS DATA
USB I/F
(C0CBCAG00031) REG 1
IC2950
6
A15
1-5 42-44
V-BOARD
RM2500
(PNJ4815M01TV) VCC
STBY 3.3V
3
OUT
1
V10
1
OUT (B3JB0000078) AI
SUB 5V
3 VCC
SN2500
R LED
AI
Block Diagram (2/3)
1 2
G LED
3
STBY 3.3V
R LED
Q2500 Q2501
G LED
TC-BOARD
VDD 3.3V ZW 3.3V ZW 1.2V PNL 12V VDD 16V (C0DBAYY00731) Gamma Voltage GEN. VGL -L10V
R
G
TO A10
(B3AGB000060)
4
AI
STBY 3.3V
5
REMOTE
7
SUB 5V
D2500
25
IC9207
VGH L20V PNL 12V VCC L3.3V
IC9004
IC9205
H_VDD8V VCC L3.3V VDD L16V H VDD8V
(C0DBAYY00715) DC/DC CONVERTER 20 PNL 12V
(C0DBAYY00730) STEP DOWN CONVERTER
RIGHT 60pin
DRIVER
1.22V
SDA SCL
2.5V
3.3V
VCC L3.3V
VDD L16V
SDA SCL
SPI ZWEI FLASH SCL/SDA
IC9003
LVCC3.3V
3.3V EEP
IC9202
TC05
SPI mini LVDS
(MN85061) ZWEI 2
LCD PANEL
9-10 51-47
PNL 12V
FLSH
5-6
SDA SCL
IC9006
IC9201 3-14 (C1AB00003252) 17-28 31-42 TFL LCD PANEL CONTROLL
92-95,97-100,102-105 107-108,110-111,113-116 118-121,123-124,126-127
(C0FBBY000076) TCON GAMMA DAT CLK
IC9206
3-6 GMA 1-4 15-18 H_VDD8V VCC L3.3V VDD L16V
LEFT 60pin
DRIVER
TC05 TO A15
LVDS
BL PWMB/PWMA
LVDS RGB 10bit
37-40 32-36 30-27 24-21 20-16 14-11
IN 1-6 (C1AB00003246)
LEVEL SHIFTER
mini-LVDS
IC9204
3
mini-LVDS OUT 1-6 CLK 1-6
TC06
2
P-BOARD
HOT COLD
P2
RELAY5V6 5V8 12V TV_MAIN_ON 17V
11 1,2 4,5 10 7 9
TO A09
P1
~
LF800 RL801
~
4 10
LF801
+
6 7
TV_SUB_ON
4 D816
T802
A_DIM INV_ON INV_PWM INV_SOS
Block Diagram (3/3)
MAIN IN
RL800 PC804
5,2 7,8 4
1
F800
Line Filter
Line Filter
11 12 13 14
IC802 PC801 IC803
A_DIM INV_ON INV_PWM INV_SOS 24V_INV
P3
15 14 13 12 1,2,3 4,5
GND
TO INVERTER
26
T803
18 10 16,17 12,13 11 15
D830 D834
4
6,7,8 9,10
~
2
-
D808
+
T801
IC804
~
IC800
2
7
1
P4
PC803 PC802 Q860
24V_INV
1,2,3 4,5
GND
TO INVERTER
IC801
16 18 1
2
6,7,8 9,10 PC805
HOT
COLD
Parts Location
NOTE:
The numbers on the exploded view below refer to the exploded view section of the Replacement Parts List.
27
23 28 8
6
25
7
29
27
NOTE:
The numbers on the exploded view below refer to the exploded view section of the Replacement Parts List.
17 5
12
15
20
12
24
26
19
4 22
3 2 13 11 14 1 18 21 16 9 10
28
Replacement Parts List
Important Safety Notice
Components Identified by mark have special characteristics important for safety. * When replacing any of these components, use only manufacturers specified parts. In case of ordering these spare parts, please always add the complete Model-Type number to your order.
RTL (Retention Time Limited) Note:
The marking (RTL) indicates that the Retention Time is Limited for this item. After the discontinuation of this assembly in production, the item will continue to be available for a specific period of time. The retention period of availability is dependent on the type of assembly, and in accordance with the laws governing part and product retention. After the end of this period, the assembly will no longer be available. The marking (X) indicates that board should be exchanged for service.
X
Cct Ref Parts Number
Description
Cct Ref .
Parts Number XYN4+F12FJK
Description SCREW BOTTOM CUSHION CARTON THERMAL PAD THERMAL PAD THERMAL PAD THERMAL PAD SPONGE TOP CUSHION IC FOR POWER SUPPLY REGULATOR IC FOR POWER SUPPLY IC FOR POWER SUPPLY IC FOR POWER SUPPLY MICRO_GENX EEPROM GENX AUDIO AMPLIFIER REGULATOR REGULATOR AUDIO VIDEO SWITCH HDMI SWITCH REGULATOR ANALOG ASIC REGULATOR REGULATOR REGULATOR REGULATOR DC/DC CONVERTER DC/DC CONVERTER REGULATOR REGULATOR IC LDA2 CLOCK GENERATOR DDR SDRAM DDR SDRAM DVB-T/C DEMODULATOR REGULATOR CI TS ASIC LEVEL SHIFTER IC SWITCH REGULATOR REGULATOR LAN TRANSCEIVER FLASH MEMORY SPI FLASH MEMORY DC/DC CONVERTER RESET IC
COMMON PARTS
EXPLODED VIEW
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 EAS16S795A ENG37F03KF K0RB00600015 K4ZZ09000014 L5EDDAT00006 N2QAYB000490 TBL0E0124 TKP0E16001 TKP0E39001 TKX0E6001 TKX0E6101 TKZ0EA5012 TKZ0EA5013 TKZ0EA5014 TKZ0EC5006 TKZ0EC5010-1 TKZ0EC5017 TKZ0EG5017 TNP8EP103AB TNP8ETC01AA TNP8EV103AD TTP0E0109 TTU0E0683-1 TUA0E7800 TXASX01QWB-3 SPEAKER UNIT TUNER CONTROL BUTTON UNIT G UNIT LCD PANEL REMOTE CONTROL STAND MTG ASSY CONNECTOR COVER AC CORD BRACKET SPEAKER BRACKET L SPEAKER BRACKET R MASK BRACKET MASK BRACKET CORNER R MASK BRACKET CORNER L VERTICAL SUPPORT BRACK METAL BRACKET BOTTOM METAL BRACKET TOP P-PCB BRACKET P P.C.B. TC P.C.B. V P.C.B. SIDE AV ASSY BACK COVER ASSY METAL CHASSIS FRAME AC CORD
X RTL RTL RTL
BOTCUS TPD0E2125-1 CARTON TPC0EA00901 FA01 FA02 FA03 FA04 TMKK394 TMKK394 TMKK395 TMKK395
FA05 TMK0EK003 TOPCUS TPD0E1126-2
I.C.s
IC800 IC801 IC802 IC803 IC804 IC1100 IC1101 IC2301 IC2950 IC2952 IC3000 IC4700 IC4701 IC5000 IC5200 IC5220 IC5280 IC5300 IC5500 IC5501 IC5603 IC5604 IC8000 IC8100 IC8240 IC8241 IC8300 IC8302 IC8400 IC8401 IC8402 IC8700 IC8701 IC8703 IC8921 IC9003 IC9004 IC9005 C0DBBYY00019 C0DABYY00017 C0DAZYY00028 C0DAEMZ00007 C0DAEMZ00007 MNZSFH9GP92 24GLP25GENX C1AB00003230 C0CBCAG00031 C0DBGYY00281 C1AB00003218 C1AB00003079 C0DBGYY00578 AN34042A-VF C0DBEYY00124 C0DBGYY00895 C0DBGYY00281 C0DBAYY00755 C0DBAYY00715 C0DBAYY00715 C0DBFYY00049 C0DBGYY00578 MN2WS0110C C1ZBZ0003967 C3ABTY000025 C3ABTY000025 C1AB00003188 C0DBFYY00041 C1AB00003193 C1AB00002913 C0ZBZ0001584 C0DBZYY00266 C0DBZYY00266 C1CB00003239 TVRR329AJ TVRR464 C0DBAYY00715 C0EBM0000026
MISCELLANEOUS COMPONENTS
. . . . . . . . . . . . . . . . R6DB/2P TBM0E9049-1 TBM0E9053 THEJ024 THTD020J TKP0E45701 TMK0EA040 TMM0E420 TMM8E18048 TPE0E9004 TPG0E9520 XTB4+12JFJK XTB4+25AFJ XTV3+6JFJ XTV3+8JFJK XTW3+10TFJ BATTERY REAR AV LABEL SIDE AV LABEL SCREW SCREW IR/LED WINDOW FELT CLAMPER TAB-RELEASE CABLE POLYBAG_PEDESTAL CARTON CAP SCREW SCREW SCREW SCREW SCREW
29
Cct Ref IC9006 IC9201 IC9202 IC9203 IC9204 IC9205 IC9206 IC9207 IC9208 PC801 PC802 PC803 PC804
Parts Number MN85061 C1AB00003252 24TCON42G20 C0CBCAG00031 C1AB00003246 C0DBAYY00730 GAMMA42G20 C0DBAYY00731 C0ABEB000037 B3PBA0000503 B3PBA0000503 B3PBA0000503 B3PBA0000503
Description ZWEI2 TFL LCD PANEL CONTROLL EEPROM PANEL REGULATOR LEVEL SHIFTER STEP-DOWN CONVERTER TCON GAMMA DAC GAMMA VOLTAGE GENERATO OPERATIONAL AMPLIFIER PHOTO COUPLER PHOTO COUPLER PHOTO COUPLER PHOTO COUPLER PHOTO COUPLER LED RECEIVER PHOTO IC DIODE
Cct Ref D2772 D2773 D2774 D2775 D2776 D2777 D2778 D2779 D2780 D3129 D3130 D4702 D4703 D4704 D4719 D4720 D4721 D4735 D4736 D4737 D4770 D4771 D4772 D4785 D5002
Parts Number B0ACCJ000048 B0ACCJ000048 DZ2J062M0L DZ2J062M0L B0ACCJ000048 B0ACCJ000048 B0ACCJ000048 B0ACCJ000048 DZ2J062M0L B0ACCJ000048 B0ACCJ000048 B0ACCJ000048 DZ2J056M0L B0JCCE000008 B0ACCJ000048 DZ2J056M0L B0JCCE000008 B0ACCJ000048 DZ2J056M0L B0JCCE000008 B0ACCJ000048 DZ2J056M0L B0JCCE000008 B0ECKM000048 DZ2J033M0L B0ACCJ000048 B0ACCJ000048 B0JCPD000026 B0BC01700015 B0ACCJ000048 B0BC010A0007 B0ACCJ000048 B0BC02400011 B0ACCJ000048 B0BC010A0007 B0ACCJ000048 B0JCPD000026 B0HCMM000014 B0ACCK000005 B0ECKM000048 B0JCPE000004 B0JCPE000004 B0ECKM000048 B0HCMM000014 B0ECKM000048 B0ECKM000048
Description DIODE DIODE DIODE DIODE DIODE DIODE DIODE DIODE DIODE DIODE DIODE DIODE ZENER DIODE DIODE DIODE ZENER DIODE DIODE DIODE ZENER DIODE DIODE DIODE ZENER DIODE DIODE DIODE ZENER DIODE DIODE DIODE DIODE DIODE DIODE DIODE DIODE ZENER DIODE DIODE DIODE DIODE DIODE DIODE DIODE DIODE DIODE DIODE DIODE DIODE DIODE DIODE
PC805 B3PBA0000503 RM2500A B3RAD0000168 SN2500 B3JB00000078
FUSES
F800-1 F800-2 F800 PA2750 PA9001 R9372 K3GE1ZA00010 K3GE1ZA00010 K5D502BNA007 K5H4022A0031 ERBSE5R00U ERBSE1R50U FUSE HOLDER FUSE HOLDER AC FUSE CHIP FUSE FUSE FUSE
DIODES
D800 D801 D803 D804 D805 D806 D807 D808 D809 D810 D811 D812 D813 D814 D815 D816 D818 D819 D821 D822 D823 D824 D825 D826 D827 D828 D829 D830 D833 D834 D835 D836 D837 D841 D1100 D1101 D2500 D2757 D2758 D2766 D2768 D2770 D2771 ERZV10V621T2 B0HCMM000014 B0JCPE000028 B0HCMM000014 B0BA01900005 B0BA02100001 B0FAAR000013 B0EBNT000026 DA2J10100L DA2J10100L DA2J10100L DA2J10100L DA2J10100L B0EAJV000004 B0EAJV000004 B0EBNT000026 B0AAKR000011 B0BA4R600003 B0BC6R700006 DA2J10100L B0BA9R600002 B0BA03600021 B0BA9R600002 B0HCMM000014 B0HAGV000004 B0JAPG000039 B0BA9R600002 B0JBSH000001 B0JAPG000039 B0JBSH000001 DA2J10100L DA2J10100L B0BA3R100004 B0BA01500003 B0JCCE000008 B0JCCE000008 B3AGB0000060 DZ2J062M0L EZJZ0V120JA DZ2J140M0L DZ2J140M0L B0ACCJ000048 B0ACCJ000048 VARISTOR DIODE DIODE DIODE DIODE DIODE DIODE DIODE DIODE DIODE DIODE DIODE DIODE DIODE DIODE DIODE DIODE DIODE DIODE DIODE DIODE DIODE DIODE DIODE DIODE DIODE DIODE DIODE DIODE DIODE DIODE DIODE DIODE DIODE DIODE DIODE LED DIODE VARISTOR ZENER DIODE ZENER DIODE DIODE DIODE
D5050 D5200 D5300 D5420 D5421 D5422 D5423 D5424 D5425 D5426 D5427 D5505 D5605 D9202 D9203 D9204 D9205 D9206 D9211 D9212 D9213
TRANSISTORS
Q800 Q801 Q802 Q803 Q804 Q805 Q806 Q807 Q2101 Q2252 Q2253 Q2254 Q2301 Q2500 Q2501 Q2504 Q3100 Q3101 Q3102 Q3103 B1ABNF000011 B1CERQ000060 DSC200100L B1ABNF000011 B1CARR000001 B1CARR000001 B1CFHD000010 DSC200100L DSA2001S0L DSA2001S0L B1AAFB000002 B1AAFB000002 DSC2001S0L DSC200100L DSC200100L DSC200100L B1ABCF000231 B1ABCF000231 B1ABCF000231 B1ABCF000231 TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR
30
Cct Ref Q3104 Q3105 Q4512 Q4513 Q4700 Q4701 Q4702 Q4703 Q4704 Q4705 Q4709 Q4710 Q5053 Q5054 Q5055 Q5240 Q5241 Q5500 Q5501 Q5502 Q5503 Q5504 Q8400 Q8401 Q9001 Q9003 Q9007 Q9008 Q9009 Q9201 Q9202 Q9203 Q9204 Q9205 Q9206 Q9207 Q9208
Parts Number B1ABCF000231 B1ABCF000231 B1HFCFA00026 B1ADCE000022 B1ABCF000231 B1ABCF000231 B1ABCF000231 B1ABCF000231 B1ABCF000231 B1ABCF000231 B1ABCF000231 B1ABCF000231 DSC2001S0L B1ADCE000022 B1ADCE000022 DSC200100L B1CHRE000005 B1MBDDA00003 B1CFRD000048 B1MBDDA00003 B1MBEDA00015 B1CFRD000048 DSC200100L DSC200100L B1ABCF000231 B1ABCF000231 B1ADCE000022 B1MBDDA00003 B1MBEDA00015 B1ABMD000006 B1DHCD000023 B1BDCF000021 B1ABNF000006 B1ABNF000006 B1ADNF000006 B1ADNF000006 B1ADCF000190
Description TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR
Cct Ref L3110 L3111 L3112 L3113 L3114 L3115 L3116 L3117 L3118 L3119 L3120 L4700 L4701 L4702 L4703 L4704 L4705 L4706 L4707 L4708 L4712 L4715 L4716 L4717 L5000 L5001 L5300 L5500 L5501 L5502 L5503 L5504 L5505 L5608 L8000 L8001 L8002 L8003 L8004 L8005 L8006 L8007 L8008
Parts Number J0JCC0000287 J0JCC0000287 J0JCC0000287 J0JCC0000287 J0JCC0000287 J0JCC0000287 J0JCC0000287 J0JCC0000287 J0JCC0000287 J0JCC0000287 J0JCC0000287 J0JYC0000068 J0JYC0000068 J0JYC0000068 J0JYC0000068 J0JYC0000068 J0JYC0000068 J0JYC0000068 J0JYC0000068 J0JYC0000068 J0JHC0000045 J0JYC0000068 J0JYC0000068 J0JYC0000068 J0JYC0000068 J0JYC0000068 G1C6R8MA0416 G1C2R2M00022 G1C3R3Z00005 G1C2R2Z00007 G1C3R3Z00004 G1C100MA0077 G1C100MA0077 J0JHC0000045 J0JCC0000287 J0JCC0000287 J0JCC0000287 J0JHC0000045 J0JKC0000021 J0JKC0000021 J0JCC0000287 J0JHC0000045 J0JCC0000287 J0JHC0000045 J0JCC0000287 J0JHC0000116 J0JCC0000287 J0JCC0000287 J0JCC0000287 J0JHC0000116 J0JHC0000116 J0JHC0000045 J0JHC0000045 J0JHC0000045 J0JCC0000287 J0JCC0000287 J0JHC0000045 J0JHC0000045 J0JCC0000287 J0JHC0000045 J0JYC0000065 J0JYC0000065 J0JBC0000116 J0JHC0000045 J0JHC0000045 J0JHC0000045 J0JHC0000045 J0JHC0000045
Description COIL COIL COIL COIL COIL COIL COIL COIL COIL COIL COIL CHIP INDUCTOR CHIP INDUCTOR CHIP INDUCTOR CHIP INDUCTOR CHIP INDUCTOR CHIP INDUCTOR CHIP INDUCTOR CHIP INDUCTOR CHIP INDUCTOR COIL BLM18PG121SN1D CHIP INDUCTOR CHIP INDUCTOR CHIP INDUCTOR CHIP INDUCTOR CHIP INDUCTOR COIL COIL COIL COIL COIL COIL COIL COIL BLM18PG121SN1D COIL COIL COIL COIL BLM18PG121SN1D COIL COIL COIL COIL BLM18PG121SN1D COIL COIL BLM18PG121SN1D COIL COIL COIL COIL COIL COIL COIL COIL BLM18PG121SN1D COIL BLM18PG121SN1D COIL BLM18PG121SN1D COIL COIL COIL BLM18PG121SN1D COIL BLM18PG121SN1D COIL COIL BLM18PG121SN1D COIL COIL COIL COIL BLM18PG121SN1D COIL BLM18PG121SN1D COIL BLM18PG121SN1D COIL BLM18PG121SN1D COIL BLM18PG121SN1D
TRANSFORMERS
T801 T802 T803 ETS26AZ169AD ETS19AB2G6AG ETS40LE116AD TRANSFORMER TRANSFORMER TRANSFORMER
COILS
L800 L801 L802 L803 L804 L1101 L2301 L2303 L2304 L2305 L2306 L2310 L2311 L2312 L2313 L2900 L2901 L2904 L2905 L2906 L2950 L3104 L3107 L3108 L3109 EXCELSA35T EXCELSA35V EXCELSA39V EXCELSA35V EXCELSA35T J0JYC0000068 J0JHC0000042 G1C220MA0416 G1C220MA0416 G1C220MA0416 G1C220MA0416 J0JHC0000078 J0JHC0000078 J0JHC0000078 J0JHC0000078 J0JCC0000278 J0JCC0000278 J0JCC0000278 J0JHC0000046 J0JCC0000278 J0JHC0000045 J0JCC0000287 J0JCC0000287 J0JCC0000287 J0JCC0000287 COIL COIL COIL COIL COIL CHIP INDUCTOR CHIP INDUCTOR SMD INDUCTOR SMD INDUCTOR SMD INDUCTOR SMD INDUCTOR COIL COIL COIL COIL CHIP INDUCTOR CHIP INDUCTOR CHIP INDUCTOR COIL CHIP INDUCTOR COIL BLM18PG121SN1D COIL COIL COIL COIL
L8009 L8010 L8011 L8012 L8013 L8014 L8015 L8016 L8017 L8018 L8019 L8020 L8021 L8022 L8023 L8024 L8100 L8102 L8103 L8104 L8300 L8302 L8303 L8304 L8400
31
Cct Ref L8401 L8701 L8702 L8705 L8706 L8707 L8708 L8850 L8920 L8921 L9001 L9003 L9004 L9005 L9006 L9007 L9008 L9009 L9010 L9011 L9012 L9013 L9014 L9015 L9016 L9201 L9202 L9203 L9204
Parts Number J0JHC0000045 J0JHC0000045 J0JHC0000045 J0JHC0000045 J0JHC0000045 J0JHC0000045 J0JHC0000045 J0JHC0000045 J0JHC0000075 J0JHC0000045 G1C100MA0072 J0JHC0000045 J0JHC0000046 J0JHC0000045 J0JHC0000046 J0JYC0000068 J0JHC0000045 J0JHC0000045 J0JHC0000045 J0JHC0000045 J0JHC0000045 G1C3R3Z00004 G1C2R2Z00006 G1C100MA0077 J0JHC0000075 J0JHC0000046 G1C6R8MA0416 G1C220MA0234 G1C220MA0234
Description COIL BLM18PG121SN1D COIL BLM18PG121SN1D COIL BLM18PG121SN1D COIL BLM18PG121SN1D COIL BLM18PG121SN1D COIL BLM18PG121SN1D COIL BLM18PG121SN1D COIL BLM18PG121SN1D COIL BLM21PG600SN1D COIL BLM18PG121SN1D COIL COIL BLM18PG121SN1D COIL COIL BLM18PG121SN1D COIL CHIP INDUCTOR COIL BLM18PG121SN1D COIL BLM18PG121SN1D COIL BLM18PG121SN1D COIL BLM18PG121SN1D COIL BLM18PG121SN1D COIL SMD INDUCTOR COIL COIL BLM21PG600SN1D COIL COIL COIL COIL
Cct Ref JS8367 JS8368 JS8369 JS8370 R800 R801 R802 R803 R804 R805 R806 R807 R808 R809 R810 R811 R812 R813 R816 R817 R818 R819 R820 R821 R822 R823 R824 R825 R826 R827 R828 R829 R830 R831 R832 R833 R834 R835 R837 R838 R839 R840 R841 R842 R843 R844 R845 R846 R847 R848 R849
Parts Number D0GAR00Z0001 D0GAR00Z0001 D0GAR00Z0001 D0GAR00Z0001 ERC12ZGK105V ERJ6ENF8202V ERJ6GEYJ683 ERJ6ENF1003V D0BF101JA032 ERJ6GEYJ104 ERJ6GEYJ470 ERJ6GEYJ222 ERJ6GEYJ271 ERJ6GEYJ150 ERJ6GEYJ473 ERJ6GEYJ473 ERJ6GEYJ561 D0GD103JA036 ERJ6GEYJ472 ERJ6ENF1303V ERJ6ENF1303V ERJ6ENF1303V ERJ6ENF1303V ERJ6ENF1303V ERJ6ENF1303V ERJ6ENF1303V ERJ6ENF1303V ERJ6ENF1303V ERJ6RBD752 ERJ6GEYJ473 ERJ6GEYJ472 ERJ6GEYJ473 ERJ6GEYJ473 ERJ6GEYJ222 ERJ6RBD912V ERJ6RBD622V ERF2AJ100P ERJ6GEYJ333 ERJ12YJ514U ERJ12YJ514U ERJ6GEYJ623 ERJ6ENF11R3V ERJ6ENF10R0V D0D21R8KA003 ERJ6GEYJ564 ERJ8GEYJ220V ERJ8GEYJ220V ERJ6GEYJ103 ERJ6GEYJ103 ERJ12YJ100U ERX2FJR47H ERJ12YJ513U ERX2FJR47H ERJ6GEYJ473 ERJ6GEYJ473 D0XB106J0003 ERJ6GEYJ222 ERJ6GEYJ331 ERJ6GEYJ114 D0GD102JA036 ERJ6GEYJ223 ERJ12YJ102U ERJ6RBD332V ERJ6RBD562V ERJ6ENF6801 D0GDR00Z0002 ERJ6GEYJ393 ERJ6GEYJ223
Description SMD .063W SMD SMD SMD CARBON SMD S.M.CARB SMD FIXED RE S.M.CARB S.M.CARB S.M.CARB S.M.CARB S.M.CARB S.M.CARB S.M.CARB S.M.CARB SMD S.M.CARB SMD SMD SMD SMD SMD SMD SMD SMD SMD SMD S.M.CARB S.M.CARB S.M.CARB S.M.CARB S.M.CARB SMD SMD FIXED S.M.CARB SMD SMD S.M.CARB SMD SMD FIXED RE S.M.CARB SMD SMD S.M.CARB S.M.CARB SMD METAL SMD METAL S.M.CARB S.M.CARB RESISTOR S.M.CARB S.M.CARB S.M.CARB SMD S.M.CARB SMD SMD SMD S.M.CARB SMD S.M.CARB S.M.CARB .063W .063W
-
0 0 0 0 1M 82K 68K 100K 100 100K 47 2K2 270 15 47K 47K 560 10K 4K7 130K 130K 130K 130K 130K 130K 130K 130K 130K 7K5 47K 4K7 47K 47K 2K2 9K1 6K2 10 33K 510K 510K 62K 11R3 10 1R8 560K 22 22 10K 10K 10 R47 51K R47 47K 47K 10M 2K2 330 110K 1K 22K 1K 3K3 5K6 6K8 0 39K 22K
.063W 0.5W 10% .125W 0.1W 0.1W 0.5W 0.1W 0.1W 0.1W 0.1W 0.1W 0.1W 0.1W 0.1W .125W 0.1W .125W .125W .125W .125W .125W .125W .125W .125W .125W 0.1W 0.1W 0.1W 0.1W 0.1W 0.1W 0.1W 0.1W 2W 0.1W 0.5W 0.5W 0.1W .125W .125W 1% 5% 1% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 1% 1% 1% 1% 1% 1% 1% 1% 1% 0.5 5% 5% 5% 5% 5% 0.5 0.5 5% 5% 5% 5% 5% 1% 1%
FILTERS
FL4800 FL4801 FL4802 FL4804 FL4805 FL4806 FL8701 FL8702 FL9001 FL9002 FL9003 FL9004 FL9005 FL9006 FL9007 FL9008 LF800 LF801 S806 EXC28CE201U EXC28CE201U EXC28CE201U EXC28CE201U EXC28CE201U EXC28CE201U EXC24CE900U EXC24CE900U EXC28CE900U EXC28CE900U EXC28CE900U EXC28CE900U EXC28CE900U EXC28CE900U EXC28CE900U EXC28CE900U ELF18N010B ELF18N010B J0LF00000025 FILTER FILTER FILTER FILTER FILTER FILTER FILTER FILTER FILTER FILTER FILTER FILTER FILTER FILTER FILTER FILTER LINE FILTER LINE FILTER FILTER
2W 10% 0.1W 5% 0.25W 0.25W 0.1W 0.1W 0.5W 2W 0.5W 2W 0.1W 0.1W 1W 0.1W 0.1W 0.1W .125W 0.1W 0.5W 0.1W 0.1W 0.1W .125W 0.1W 0.1W 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 0.5 0.5 1% 5% 5%
CRYSTALS
X1101 X8002 X8100 X8300 X9001 X9201 H0J100500035 H0J245500101 H0J270500120 H0J410500001 H0J270500113 H2D100500004 CRYSTAL CRYSTAL CRYSTAL CRYSTAL CRYSTAL CRYSTAL 8 0 0 0 0 0 0 0 0 0
R850 R851 R854 R855 R856 R857 .063W .063W .063W .063W .063W .063W .063W .063W .063W R858 R859 R860 R861 R862 R863 R864 R865 R867 R868 R869
RESISTORS
CF800 JS1001 JS1012 JS8360 JS8361 JS8362 JS8363 JS8364 JS8365 JS8366 D4CAY8R00003 D0GAR00Z0001 D0GAR00Z0001 D0GAR00Z0001 D0GAR00Z0001 D0GAR00Z0001 D0GAR00Z0001 D0GAR00Z0001 D0GAR00Z0001 D0GAR00Z0001 NTC THER SMD SMD SMD SMD SMD SMD SMD SMD SMD
32
Cct Ref R870 R871 R872 R873 R874 R875 R876 R877 R878 R879 R880 R881 R882 R883 R884 R885 R0900 R0901 R0902 R0903 R0904 R0907 R0910 R0940 R0941 R0942 R0943 R0944 R0945 R0946 R0947 R0948 R0949 R0952 R0953 R0958 R0959 R0966 R0967 R0972 R0973 R0976 R0977 R0978 R0979 R0980 R0981 R0982 R0983 R0984 R0985 R0986 R0987 R1110 R1178 R1180 R1183 R1187 R1189 R1191 R1224 R1225 R1237 R1243 R1502 R1504 R1506 R1514
Parts Number D0GD103JA036 ERJ6RBD122 ERJ6RBD203V ERJ6RBD242V ERJ6GEYJ272 ERJ12YJ272U ERJ12YJ272U ERJ12YJ272U ERJ12YJ272U ERJ12YJ272U ERJ12YJ514U ERJ12YJ514U ERJ12YJ513U ERJ6GEYJ102 ERJ12YJ101U ERJ6GEYJ331 D0GA680JA015 D0GA680JA015 EXB28V680JX D0GA680JA015 EXB28V103JX ERJ2GEJ103X ERJ2GEJ103X D0GA680JA015 D0GA680JA015 D0GA680JA015 D0GA680JA015 D0GA680JA015 D0GA680JA015 ERJ2GEJ220X ERJ2GEJ220X D0GA472JA015 D0GA472JA015 ERJ2GEJ220X ERJ2GEJ220X ERJ2GEJ220X ERJ2GEJ220X D0GA472JA015 D0GA472JA015 ERJ2GEJ220X ERJ2GEJ220X ERJ2GEJ220X ERJ2GEJ220X ERJ2GEJ220X ERJ2GEJ220X D0GA472JA015 D0GA472JA015 ERJ2GEJ220X ERJ2GEJ220X D0GA472JA015 D0GA472JA015 ERJ2GEJ220X ERJ2GEJ220X D0GA821JA015 D0GA331JA015 ERJ2GEJ102X D0GA472JA015 D0GA273JA015 D1BB7151A055 D0GA473JA015 ERJ2GEJ103X ERJ2GEJ103X ERJ2GEJ102X D0GA473JA015 D0GA473JA015 D0GA473JA015 D0GA473JA015 D0GA182JA015
Description SMD SMD SMD SMD S.M.CARB SMD SMD SMD SMD SMD SMD SMD SMD S.M.CARB SMD S.M.CARB SMD SMD SMD SMD SMD SMD SMD SMD SMD SMD SMD SMD SMD SMD SMD SMD SMD SMD SMD SMD SMD SMD SMD SMD SMD SMD SMD SMD SMD SMD SMD SMD SMD SMD SMD SMD SMD SMD SMD SMD SMD SMD SMD SMD SMD SMD SMD SMD SMD SMD SMD SMD
.125W 0.1W 0.1W 0.1W 0.1W 0.5W 0.5W 0.5W 0.5W 0.5W 0.5W 0.5W 0.5W 0.1W 0.5W 0.1W .063W .063W .031W .063W .031W .063W .063W .063W .063W .063W .063W .063W .063W .063W .063W .063W .063W .063W .063W .063W .063W .063W .063W .063W .063W .063W .063W .063W .063W .063W .063W .063W .063W .063W .063W .063W .063W .063W .063W .063W .063W .063W 0.1W .063W .063W .063W .063W .063W .063W .063W .063W .063W
5% 0.5 0.5 0.5 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 1% 5% 5% 5% 5% 5% 5% 5% 5% 5%
10K 1K2 20K 2K4 2K7 2K7 2K7 2K7 2K7 2K7 510K 510K 51K 1K 100 330 68 68 68 68 10K 10K 10K 68 68 68 68 68 68 22 22 4K7 4K7 22 22 22 22 4K7 4K7 22 22 22 22 22 22 4K7 4K7 22 22 4K7 4K7 22 22 820 330 1K 4K7 27K 7K15 47K 10K 10K 1K 47K 47K 47K 47K 1K8
Cct Ref R1515 R1516 R1520 R1521 R1568 R1569 R2053 R2055 R2069 R2070 R2101 R2102 R2107 R2135 R2139 R2140 R2254 R2255 R2256 R2257 R2258 R2259 R2301 R2302 R2303 R2304 R2305 R2310 R2331 R2340 R2341 R2342 R2500 R2502 R2504 R2507 R2508 R2509 R2512 R2514 R2515 R2516 R2517 R2518 R2529 R2530 R2532 R2543 R2751 R2752 R2753 R2754 R2755 R2756 R2764 R2765 R2767 R2768 R2786 R2795 R2907 R2914 R2926 R2960 R3003 R3006 R3007 R3012
Parts Number D0GA473JA015 D0GA473JA015 ERJ2GEJ103X ERJ2GEJ104X D0GA683JA015 D0GA223JA015 D1BB1403A055 D1BB1403A055 ERJ2GEJ103X ERJ2GEJ103X D0GA332JA015 D0GA472JA015 D0GAR00Z0001 ERJ2GEJ102X ERJ2GEJ221X ERJ2GEJ221X ERJ2GEJ102X D0GA473JA015 ERJ2GEJ103X D0GA105JA015 D0GA101JA015 D0GA101JA015 ERJ2GEJ103X EXB28V220JX D0GA100JA015 D0GA100JA015 D0GA100JA015 ERJ2GEJ103X D0GA473JA015 D0GA473JA015 D0GA473JA015 ERJ2GEJ103X D1BA6800A014 D0GA473JA015 D0GA223JA015 D0GA473JA015 ERJ2GEJ103X D1BA1821A014 D0GA470JA015 D0GA562JA015 D0GA124JA015 ERJ2GEJ473X ERJ2GEJ104X ERJ2GEJ103X D0GA332JA015 D0GA332JA015 D0GAR00Z0001 D0GAR00Z0001 ERJ6GEY0R00 ERJ6GEY0R00 D0GAR00Z0001 D0GAR00Z0001 ERJ2GEJ102X ERJ2GEJ102X D0GA473JA015 ERJ6GEY0R00 ERJ6GEY0R00 ERJ6GEY0R00 D0GA101JA015 D0GA101JA015 D0GAR00Z0001 ERJ2GEJ103X D0GA680JA015 D0GA153JA015 ERJ2GEJ104X D0GA680JA015 D0GA680JA015 ERJ2GEJ221X
Description SMD .063W SMD SMD SMD SMD SMD SMD SMD SMD SMD SMD SMD SMD SMD SMD SMD SMD SMD SMD SMD SMD SMD SMD SMD SMD SMD SMD SMD SMD SMD SMD SMD SMD SMD SMD SMD SMD SMD SMD SMD SMD SMD SMD SMD SMD SMD SMD SMD S.M.CARB S.M.CARB SMD SMD SMD SMD SMD S.M.CARB S.M.CARB S.M.CARB SMD SMD SMD SMD SMD SMD SMD SMD SMD SMD .063W .063W .063W .063W .063W 0.1W 0.1W .063W .063W .063W .063W .063W .063W .063W .063W .063W .063W .063W .063W .063W .063W .063W .031W .063W .063W .063W .063W .063W .063W .063W .063W .063W .063W .063W .063W .063W .063W .063W .063W .063W .063W .063W .063W .063W .063W .063W .063W 0.1W 0.1W .063W .063W .063W .063W .063W 0.1W 0.1W 0.1W .063W .063W .063W .063W .063W .063W .063W .063W .063W .063W
5% 5% 5% 5% 5% 5% 1% 1% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 1% 5% 5% 5% 5% 1% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5%
47K 47K 10K 100K 68K 22K 140K 140K 10K 10K 3K3 4K7 0 1K 220 220 1K 47K 10K 1M 100 100 10K 22 10 10 10 10K 47K 47K 47K 10K 680 47K 22K 47K 10K 1K82 47 5K6 120K 47K 100K 10K 3K3 3K3 0 0 0 0 0 0 1K 1K 47K 0 0 0 100 100 0 10K 68 15K 100K 68 68 220
33
Cct Ref R3013 R3101 R3102 R3103 R3104 R3105 R3108 R3109 R3117 R3120 R3121 R3123 R3124 R3125 R3126 R3127 R3128 R3129 R3130 R3137 R3138 R3139 R3140 R3141 R3142 R3143 R3145 R3147 R3150 R3151 R3152 R3153 R3154 R3155 R3156 R3157 R3158 R3159 R3161 R3162 R3163 R3164 R3165 R3166 R3167 R3168 R3169 R3170 R3171 R3172 R3173 R3174 R3175 R3176 R3177 R3178 R3179 R3180 R3181 R3182 R3183 R3184 R3185 R3186 R3187 R3188 R3189 R3190
Parts Number ERJ2GEJ221X D0GA472JA015 D0GA472JA015 ERJ6ENF75R0 ERJ6ENF75R0 ERJ6ENF75R0 D0GA101JA015 ERJ8ENF75R0 ERJ2GEJ221X ERJ2GEJ221X ERJ2GEJ221X D0GA680JA015 D0GA680JA015 D0GA680JA015 D0GA680JA015 D0GA680JA015 ERJ2GEJ104X ERJ2GEJ104X ERJ6ENF75R0 ERJ6ENF75R0 ERJ8ENF75R0 ERJ8ENF75R0 ERJ8ENF75R0 ERJ8ENF75R0 ERJ8ENF75R0 ERJ8ENF75R0 ERJ8ENF75R0 ERJ8ENF75R0 ERJ2GEJ221X ERJ2GEJ221X ERJ2GEJ221X ERJ2GEJ221X ERJ2GEJ221X ERJ2GEJ221X ERJ2GEJ221X ERJ2GEJ221X ERJ2GEJ221X ERJ2GEJ221X ERJ2GEJ104X ERJ2GEJ104X ERJ2GEJ104X ERJ2GEJ104X D0GA333JA015 D0GA333JA015 D0GA333JA015 D0GA333JA015 D0GA101JA015 D0GA101JA015 D0GA101JA015 D0GA101JA015 ERJ2GEJ221X ERJ2GEJ221X ERJ2GEJ221X ERJ2GEJ221X D0GA331JA015 D0GA331JA015 D0GA331JA015 D0GA331JA015 ERJ6ENF75R0 ERJ6ENF75R0 ERJ6ENF75R0 ERJ2GEJ104X ERJ2GEJ104X D0GA333JA015 D0GA333JA015 ERJ2GEJ221X ERJ2GEJ221X D0GA101JA015
Description SMD SMD SMD SMD SMD SMD SMD SMD SMD SMD SMD SMD SMD SMD SMD SMD SMD SMD SMD SMD SMD SMD SMD SMD SMD SMD SMD SMD SMD SMD SMD SMD SMD SMD SMD SMD SMD SMD SMD SMD SMD SMD SMD SMD SMD SMD SMD SMD SMD SMD SMD SMD SMD SMD SMD SMD SMD SMD SMD SMD SMD SMD SMD SMD SMD SMD SMD SMD
.063W .063W .063W .125W .125W .125W .063W 0.25W .063W .063W .063W .063W .063W .063W .063W .063W .063W .063W .125W .125W 0.25W 0.25W 0.25W 0.25W 0.25W 0.25W 0.25W 0.25W .063W .063W .063W .063W .063W .063W .063W .063W .063W .063W .063W .063W .063W .063W .063W .063W .063W .063W .063W .063W .063W .063W .063W .063W .063W .063W .063W .063W .063W .063W .125W .125W .125W .063W .063W .063W .063W .063W .063W .063W
5% 5% 5% 1% 1% 1% 5% 1% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 1% 1% 1% 1% 1% 1% 1% 1% 1% 1% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 1% 1% 1% 5% 5% 5% 5% 5% 5% 5%
220 4K7 4K7 75 75 75 100 75 220 220 220 68 68 68 68 68 100K 100K 75 75 75 75 75 75 75 75 75 75 220 220 220 220 220 220 220 220 220 220 100K 100K 100K 100K 33K 33K 33K 33K 100 100 100 100 220 220 220 220 330 330 330 330 75 75 75 100K 100K 33K 33K 220 220 100
Cct Ref R3191 R3192 R3193 R3194 R3195 R3196 R3197 R3198 R3201 R3202 R3203 R3204 R3205 R3206 R3207 R3208 R3209 R3212 R3240 R3241 R3990 R3991 R4208 R4210 R4548 R4549 R4550 R4551 R4552 R4553 R4554 R4556 R4557 R4560 R4651 R4655 R4659 R4663 R4666 R4668 R4670 R4672 R4676 R4677 R4702 R4703 R4704 R4706 R4707 R4708 R4709 R4710 R4711 R4712 R4715 R4716 R4717 R4719 R4720 R4721 R4722 R4723 R4724 R4725 R4728 R4729 R4730 R4732
Parts Number D0GA101JA015 D0GA820JA015 D0GA820JA015 D0GA331JA015 D0GA331JA015 D0GA820JA015 D0GA680JA015 D0GA680JA015 ERJ8ENF75R0 ERJ8ENF75R0 D1BA2152A014 D1BA2152A014 D1BA1302A014 D1BA1302A014 D0GA273JA015 D0GA273JA015 D0GA680JA015 D0GA680JA015 D0GA333JA015 D0GA333JA015 ERJ2GEJ103X ERJ2GEJ103X D0GA473JA015 D0GA473JA015 ERJ2GEJ220X D0GA151JA015 D0GA151JA015 D0GA151JA015 D0GA560JA015 ERJ2GEJ103X ERJ2GEJ102X ERJ2GEJ103X D0GAR00Z0001 D0GA473JA015 ERJ2GEJ220X ERJ2GEJ220X ERJ2GEJ220X ERJ2GEJ220X D0GA330JA015 D0GA330JA015 D0GA330JA015 D0GA330JA015 ERJ2GEJ102X D0GA122JA015 ERJ2GEJ103X D0GA330JA015 D0GA473JA015 ERJ2GEJ103X D0GA473JA015 ERJ2GEJ103X ERJ2GEJ103X D0GA473JA015 ERJ2GEJ102X D0GA473JA015 ERJ2GEJ103X D0GA330JA015 D0GA473JA015 ERJ2GEJ103X D0GA473JA015 ERJ2GEJ103X ERJ2GEJ103X D0GA473JA015 ERJ2GEJ102X D0GA473JA015 ERJ2GEJ103X D0GA330JA015 D0GA473JA015 ERJ2GEJ103X
Description SMD .063W SMD SMD SMD SMD SMD SMD SMD SMD SMD SMD SMD SMD SMD SMD SMD SMD SMD SMD SMD SMD SMD SMD SMD SMD SMD SMD SMD SMD SMD SMD SMD SMD SMD SMD SMD SMD SMD SMD SMD SMD SMD SMD SMD SMD SMD SMD SMD SMD SMD SMD SMD SMD SMD SMD SMD SMD SMD SMD SMD SMD SMD SMD SMD SMD SMD SMD SMD .063W .063W .063W .063W .063W .063W .063W 0.25W 0.25W .063W .063W .063W .063W .063W .063W .063W .063W .063W .063W .063W .063W .063W .063W .063W .063W .063W .063W .063W .063W .063W .063W .063W .063W .063W .063W .063W .063W .063W .063W .063W .063W .063W .063W .063W .063W .063W .063W .063W .063W .063W .063W .063W .063W .063W .063W .063W .063W .063W .063W .063W .063W .063W .063W .063W .063W .063W .063W
5% 5% 5% 5% 5% 5% 5% 5% 1% 1% 1% 1% 1% 1% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5% 5%
100 82 82 330 330 82 68 68 75 75 21K5 21K5 13K 13K 27K 27K 68 68 33K 33K 10K 10K 47K 47K 22 150 15