Text preview for : panasonic_sdr-h40.pdf part of Panasonic SDR-H40 Service Manual
Back to : panasonic_sdr-h40.zip | Home
ORDER NO.VM0712053CE B27
SD Card / Hard Disk Video Camera
Model No.
SDR-H40P
SDR-H40PC SDR-H40EG SDR-H40E SDR-H40EB SDR-H40EP SDR-H40EF SDR-H40GC SDR-H40GN SDR-H40PL SDR-H48GK
VOL.1
Colour (S)....................Silver Type
© 2007 Matsushita Electric Industrial Co., Ltd. All rights reserved. Unauthorized copying and distribution is a violation of law.
SDR-H40P
CONTENTS
Page
1 Safety Precaution 1.1. General Guidelines 2 Warning 2.1. Prevention of Electrostatic Discharge (ESD) to Electrostatic Sensitive (ES) Devices 2.2. Service caution based on legal restrictions 2.3. Caution for AC Cord (For EB/GC) 2.4. How to Replace the Lithium Battery (PROCEDURE) 2.5. How to Recycle the Lithium Battery (U.S. Only) 3 Service Navigation 3.1. Service Information 3.2. Precautions for Handling HDD 3.3. Formatting HDD 4 Specifications 5 Location of Controls and Components 6 Service Mode 6.1. Error Display 6.2. Service Menu 6.3. About Default Setting 7 Service Fixture & Tools 7.1. Service Tools and Equipment 8 Disassembly and Assembly Instructions 8.1. Disassembly Frow Chart 8.2. P.C.B. Layout 8.3. Disassembly Procedures 8.4. Disassembly Procedures of Camera Lens Unit 4 5 6 7 8 9 9 10 14 15 16 18 18 18 23 24 24 25 25 25 26 31 3 3 4 9 Measurements and Adjustments 9.1. EEPROM Data for spare parts of the MAIN P.C.B. 9.2. Service Positions 9.3. Location for Connectors of the Main P.C.B. 9.4. Electrical Adjustment Procedures 10 Maintenance 10.1. Cleaning Lens and LCD Panel 11 Schematic Diagrams 11.1. OVERALL SCHEMATIC DIAGRAM 11.2. INTERCONNECTION SCHEMATIC DIAGRAM 11.3. FRONT SCHEMATIC DIAGRAM 11.4. LCD BACKLIGHT SCHEMATIC DIAGRAM 11.5. REAR CASE SCHEMATIC DIAGRAM 11.6. SHAFT FPC SCHEMATIC DIAGRAM 11.7. HDD FPC UNIT SCHEMATIC DIAGRAM 11.8. CCD SCHEMATIC DIAGRAM 11.9. SIDE L UNIT SCHEMATIC DIAGRAM 11.10. SD SCHEMATIC DIAGRAM 12 Printed Circuit Board 12.1. SD P.C.B. 12.2. FRONT P.C.B. 12.3. LCD BACKLIGHT P.C.B. 13 Parts and Exploded Views 13.1. Exploded Views 13.2. Replacement Parts List
Page
32 32 32 34 35 39 39 41 41 42 43 44 45 45 45 46 47 48 49 49 50 51 53 53 58
2
SDR-H40P
1 Safety Precaution
1.1. General Guidelines
1. IMPORTANT SAFETY NOTICE There are special components used in this equipment which are important for safety. These parts are marked by in the Schematic Diagrams, Circuit Board Layout, Exploded Views and Replacement Parts List. It is essential that these critical parts should be replaced with manufacturer's specified parts to prevent X-RADIATION, shock fire, or other hazards. Do not modify the original design without permission of manufacturer. 2. An Isolation Transformer should always be used during the servicing of AC Adaptor whose chassis is not isolated from the AC power line. Use a transformer of adequate power rating as this protects the technician from accidents resulting in personal injury from electrical shocks. It will also protect AC Adaptor from being damaged by accidental shorting that may occur during servicing. 3. When servicing, observe the original lead dress. It a short circuit is found, replace all parts which have been overheated or damaged by the short circuit. 4. After servicing, see to it that all the protective devices such as insulation barriers, insulation papers shields are properly installed. 5. After servicing, make the following leakage current checks to prevent the customer from being exposed to shock hazards.
1.1.1.
Leakage Current Cold Check
1. Unplug the AC cord and connect a jumper between the two prongs on the plug. 2. Measure the resistance value, with an ohmmeter, between the jumpered AC plug and each exposed metallic cabinet part on the equipment such as screwheads, connectors, control shafts, etc. When the exposed metallic part has a return path to the chassis, the reading should be between 1MW and 5.2MW. When the exposed metal does not have a return path to the chassis, the reading must be infinity.
1.1.2.
Leakage current hot check (See Figure 1)
1. Plug the AC cord directly into the AC outlet. Do not use an isolation transformer for this check. 2. Connect "A" to exposed metallic part on the set. And connect "B" to a good earth ground, as shown in Figure 1. 3. Use an AC voltmeter, with 1 kW/V or more sensitivity, to measure the potential across the resistor. 4. Check each exposed metallic part, and measure the voltage at each point. 5. Reverse the AC plug in the AC outlet and repeat each of the above measurements. 6. The potential at any point should not exceed 0.25 V RMS. A leakage current tester (Simpson Model 229 or equivalent) may be used to make the hot checks, leakage current must not exceed 1/2 mA. In case a measurement is outside of the limits specified, there is a possibility of a shock hazard, and the equipment should be repaired and rechecked before it is returned to the customer.
Figure 1
3
SDR-H40P
2 Warning
2.1. Prevention of Electrostatic Discharge (ESD) to Electrostatic Sensitive (ES) Devices
Some semiconductor (solid state) devices can be damaged easily by static electricity. Such components commonly are called Electrostatic Sensitive (ES) Devices. Examples of typical ES devices are integrated circuits and some field-effect transistors and semiconductor "chip" components. The following techniques should be used to help reduce the incidence of component damage caused by electrostatic discharge (ESD). 1. Immediately before handling any semiconductor component or semiconductor-equipped assembly, drain off any ESD on your body by touching a known earth ground. Alternatively, obtain and wear a commercially available discharging ESD wrist strap, which should be removed for potential shock reasons prior to applying power to the unit under test. 2. After removing an electrical assembly equipped with ES devices, place the assembly on a conductive surface such as aluminum foil, to prevent electrostatic charge buildup or exposure of the assembly. 3. Use only a grounded-tip soldering iron to solder or unsolder ES devices. 4. Use only an antistatic solder removal device. Some solder removal devices not classified as "antistatic (ESD protected)" can generate electrical charge sufficient to damage ES devices. 5. Do not use freon-propelled chemicals. These can generate electrical charges sufficient to damage ES devices. 6. Do not remove a replacement ES device from its protective package until immediately before you are ready to install it. (Most replacement ES devices are packaged with leads electrically shorted together by conductive foam, aluminum foil or comparable conductive material). 7. Immediately before removing the protective material from the leads of a replacement ES device, touch the protective material to the chassis or circuit assembly into which the device will be installed. CAUTION: Be sure no power is applied to the chassis or circuit, and observe all other safety precautions. 8. Minimize bodily motions when handling unpackaged replacement ES devices. (Otherwise harmless motion such as the brushing together of your clothes fabric or the lifting of your foot from a carpeted floor can generate static electricity (ESD) sufficient to damage an ES device).
4
SDR-H40P
2.2.
2.2.1.
Service caution based on legal restrictions
General description about Lead Free Solder (PbF)
The lead free solder has been used in the mounting process of all electrical components on the printed circuit boards used for this equipment in considering the globally environmental conservation. The normal solder is the alloy of tin (Sn) and lead (Pb). On the other hand, the lead free solder is the alloy mainly consists of tin (Sn), silver (Ag) and Copper (Cu), and the melting point of the lead free solder is higher approx.30 degrees C (86°F) more than that of the normal solder. Definition of PCB Lead Free Solder being used
The letter of "PbF" is printed either foil side or components side on the PCB using the lead free solder. (See right figure)
Service caution for repair work using Lead Free Solder (PbF) · The lead free solder has to be used when repairing the equipment for which the lead free solder is used. (Definition: The letter of "PbF" is printed on the PCB using the lead free solder.) · To put lead free solder, it should be well molten and mixed with the original lead free solder. · Remove the remaining lead free solder on the PCB cleanly for soldering of the new IC. · Since the melting point of the lead free solder is higher than that of the normal lead solder, it takes the longer time to melt the lead free solder. · Use the soldering iron (more than 70W) equipped with the temperature control after setting the temperature at 350±30 degrees C (662±86°F). Recommended Lead Free Solder (Service Parts Route.) · The following 3 types of lead free solder are available through the service parts route. RFKZ03D01K-----------(0.3mm 100g Reel) RFKZ06D01K-----------(0.6mm 100g Reel) RFKZ10D01K-----------(1.0mm 100g Reel) Note * Ingredient: tin (Sn), 96.5%, silver (Ag) 3.0%, Copper (Cu) 0.5%, Cobalt (Co) / Germanium (Ge) 0.1 to 0.3%
5
SDR-H40P
2.3.
2.3.1.
Caution for AC Cord (For EB/GC)
Information for your safety
Blue Brown
Neutral Live
IMPORTANT Your attention is drawn to the fact that recording of prerecorded tapes or discs or other published or broadcast material may infringe copyright laws. WARNING To reduce the risk of fire or shock hazard, do not expose this equipment to rain or moisture. CAUTION To reduce the risk of fire or shock hazard and annoying interference, use the recommended accessories only. FOR YOUR SAFETY DO NOT REMOVE THE OUTER COVER To prevent electric shock, do not remove the cover. No user serviceable parts inside. Refer servicing to qualified service personnel.
As the colours of the wires in the mains lead of this appliance may not correspond with the coloured markings identifying the terminals in your plug, proceed as follows: The wire which is coloured BLUE must be connected to the terminal in the plug which is marked with the letter N or coloured BLACK. The wire which is coloured BROWN must be connected to the terminal in the plug which is marked with the letter L or coloured RED. Under no circumstances should either of these wires be connected to the earth terminal of the three pin plug, marked with the letter E or the Earth Symbol.
2.3.2.
Caution for AC mains lead
2.3.2.2.
Before use
For your safety, please read the following text carefully. This appliance is supplied with a moulded three-pin mains plug for your safety and convenience. A 5-ampere fuse is fitted in this plug. Should the fuse need to be replaced please ensure that the replacement fuse has a rating of 5 amperes and it is approved by ASTA or BSI to BS1362 Check for the ASRA mark or the BSI mark on the body of the fuse.
remove the Connector Cover as follows.
2.3.2.3.
If the plug contains a removable fuse cover you must ensure that it is refitted when the fuse is replaced. If you lose the fuse cover, the plug must not be used until a replacement cover is obtained. A replacement fuse cover can be purchased from your local Panasonic Dealer. If the fitted moulded plug is unsuitable for the socket outlet in your home then the fuse should be removed and the plug cut off and disposed of safety. There is a danger of severe electrical shock if the cut off plug is inserted into any 13-ampere socket. If a new plug is to be fitted please observe the wiring code as shown below. If in any doubt, please consult a qualified electrician.
How to replace the Fuse
1. Remove the Fuse Cover with a screwdriver.
2. Replace the fuse and attach the Fuse cover.
2.3.2.1.
Important
The wires in this mains lead are coloured in accordance with the following code:
6
SDR-H40P
2.4.
How to Replace the Lithium Battery (PROCEDURE)
1. Remove the SD P.C.B.. (Refer to Disassembly Procedures.) 2. Unsolder the Lithium Battery "ML-621S/F9D" and then replace the new one. (See Figure B1.)
Fig. B1
Note: The lithium battery is a critical component. (Type No.: ML-621S/F9D Manufactured by Panasonic.) It must never be subjected to excessive heat or discharge. It must therefore only be fitted in equipment designed specifically for its use. Replacement batteries must be of the same type and manufacture. They must be fitted in the same manner and location as the original battery, with the correct polarity contacts observed. Do not attempt to re-charge the old battery or re-use it for any other purpose. It should be disposed of in waste products destined for burial rather than incineration.
7
SDR-H40P
2.5.
How to Recycle the Lithium Battery (U.S. Only)
8
SDR-H40P
3 Service Navigation
3.1. Service Information
This service manual contains technical information which will allow service personnel´s to understand and service this model. Please place orders using the parts list and not the drawing reference numbers. If the circuit is changed or modified, this information will be followed by supplement service manual to be filed with original service manual. Notes 1: 1. VSK0697 is indicated on AC Adapter used on the following models: SDR-H40P/PC/PL. However, the AC Adapter replacement part number is DE-A51BA which should be used when ordering. 2. VSK0698 is indicated on AC Adapter used in the following models: SDR-H40EG/E/EB/EP/EF/GC/GN. However, the AC Adapter replacement part number is DE-A51CA which should be used when ordering. 3. VSK0698 is indicated on AC Adapter used on the following model: SDR-H48GK. However, the AC Adapter replacement part number is DE-A51DA which should be used when ordering. Notes 2: 1) This service manual does not contain the following information, because of the impossibility of sevicing at component level. 1. Schematic Diagram, Block Diagram and P.C.B. layout of Main P.C.B. 2. Parts List for individual parts of Main P.C.B. 2) The following category are recycle module part. Please send them to Central Repair Center. *Main P.C.B. (LSEP8443A1: SDR-H40P/PC/PL) (LSEP8443P1: SDR-H40EG/E/EB/EP/EF/GC/GN, SDR-H48GK) When a part replacement is required for repairing each Main P.C.B., replace the assembly parts. (Main P.C.B.) The following circuits are contained in Main P.C.B. 1. Main Connection Circuit 2. AVIO Circuit 3. Video Circuit 4. Memory Circuit 5. USB Host Circuit 6. LCD Circuit 7. Power Circuit 8. HDD G-Sensor Circuit 9. Lens Drive Circuit 10. TG/AFE Circuit 11. SYSCON Circuit 12. Sub SYSCON Circuit
9
SDR-H40P
3.2.
Precautions for Handling HDD
1. Handle HDD very carefully to prevent the static electricity and shock. 2. Set the HDD quickly after taking it out from the package. Make sure to put the HDD on buffer materials, etc.
3.2.1.
Precautions at incoming process and for opening packages
10
SDR-H40P
3.2.2.
Precautions for installing HDD
11
SDR-H40P
3.2.3.
Precautions for inserting and removing HDD FPC
Make sure to use the tool (LSVQ0112) when locking and unlocking the lock lever of HDD FPC connector. Do not lock the lock lever without inserting HDD FPC. Otherwise, the connector may be damaged.
12
SDR-H40P
Make sure to use the tool (LSVQ0112) when opening and closing the lock lever. *See "" (Fig. D4) for attaching to the unit.
13
SDR-H40P
3.3.
Formatting HDD
When HDD is exchanged, format HDD as the procedure below. Without formatting, the error message appears on the LCD display when accessing HDD. Rotate the mode dial to select Select [HDD] in [MEDIA SELECT]. 1. Press the MENU button, then select [SETUP] ® [FORMAT HDD] ® [YES] and press the joystick. .
2. When the confirmation message appears, select [YES], then press the joystick. · When formatting is complete, press the MENU button to exit the message screen. Note: · During formatting, do not turn this unit off. · When you format the HDD, use a battery with sufficient battery power or the AC adaptor. · During formatting, do not cause any vibrations or impacts to this unit.
14
SDR-H40P
4 Specifications
15
SDR-H40P
5 Location of Controls and Components
Followings are the Location of Controls and Components for SDR-H40P/PC as a sample. For other models, refer to each Operatin Instructions.
16
SDR-H40P
17
SDR-H40P
6 Service Mode
6.1. Error Display
"PUSH THE RESET SWITCH" is displayed automatically on the LCD Monitor when an undesirable condition has occurred.
Fig. 1
Note: When "PUSH THE RESET SWITCH" is displayed repeatedly, service is required. Check the Error Code which is listed in the Service Menu.
6.2.
Service Menu
When abnormal detection contents are confirmed, do the following operation. Automatic diagnosis code will bedisplayed. (Service Menu) To enter the Service Menu Push the [DELETE], [JOYSTICK CONTROL LEFT] and [DVD COPY] simultaneously for 3 seconds (with no SD Card inserted). Note: If a SD Card is inserted, the above operation will not work.
Fig. 2-1
18
SDR-H40P
Note: Only perform items 1, 2, 3, 4, 9, 10 and 14 in the Service Menu. To select the Item of Service Menu 1. Press [JOYSTICK CONTROL UP/DOWN] to select item [1], [2], [3], [4], [9], [10] or [14]. 2. Press [JOYSTICK CONTROL RIGHT] to display [YES/NO] screen. 3. Press [JOYSTICK CONTROL UP/DOWN] to select [YES]. 4. Press [JOYSTICK CONTROL CENTER] to end.
Fig. 2-2
19
SDR-H40P
Fig. 2-3
20
SDR-H40P
Fig. 2-4
21
SDR-H40P
Fig. 2-5
22
SDR-H40P
Fig. 2-6
To exit the Service Menu Unplug the AC Cord.
6.3.
6.3.1.
About Default Setting
How to set the Default Setting
The data of Menu, Mode, Card and EEPROM setting, etc. is set to the default condition in factory.
1. Turn the Power on and set the Mode Dial to [VIDEO RECORDING MODE]. 2. When pressing [DELETE], [JOYSTICK CONTROL RIGHT] and [DVD COPY] for more than 3 minutes simultaneously (with no SD Card inserted), the items below are set to the Default Setting. 1. Menu, Mode, Adjusted Value 2. Card format 3. Reset of picture files and directory number (Set the picture record file number to 1) 4. Clear the information of Mechanism Lock 5. Set the time setting to no-setting
23
SDR-H40P
7 Service Fixture & Tools
7.1. Service Tools and Equipment
24
SDR-H40P
8 Disassembly and Assembly Instructions
8.1. Disassembly Frow Chart
This flow chart indicates the disassembly steps the cabinet parts and P.C.B.. Unit in order to access to be serviced. When reinstalling, perform the steps in the reverse order.
8.2.
P.C.B. Layout
Fig. F1
25
SDR-H40P
8.3.
No. 1
Disassembly Procedures
Item / Part Fig. Removal (Screw,Connector,FPC. & Other) 5-Screws (A) 1-Screw (B) 2-Tabs Grip Unit Open the LCD Unit and Jack Cover. 3-Screws (C) 1-Screw (D) 1-Connector FP61 Operation Unit 4-Screws (E) 1-Connector FP21 Head Disk Drive, HDD Cushion, HDD Shield Case 4-Screws (F) 1-Tab 1-Connector FP6501 Front/ Mic Unit 3-Screws (G) 1-Connector FP81 Side R/ LCD Unit 1-Screw (H) 4-Connectors FP11,FP31,FP51,FP71 Main P.C.B. & Main Plate Unit 3-Screws (I) Main Plate Unit,Main P.C.B. 1-Screw (J) Lens Unit 3-Screws (K) Front P.C.B. 5-Screws (L) 1-Tab 1-Connector P6301 Speaker Angle,SD P.C.B. Turn the LCD Case to the arrow direction so that the screws can be seen, and remove the 2 screws (M). 6-Tabs LCD Case A Unit 1-Connector FP8101 LCD Case B Unit 1-Connector FP8102 1-Screw (N) 6-Tabs LCD Backlight P.C.B.
Flow-Chart for Disassembly Procedure
Grip Unit
2
Operation Unit
3
HDD Unit
4
Front/ Mic Unit
5
Side R/ LCD Unit Main P.C.B.
6
Fig. D1
7 8 9
Lens Unit Front P.C.B. SD P.C.B.
10
LCD Backlight P.C.B.
Fig. D2
26
SDR-H40P
Note for replacing HDD · Be sure to use the tool when inserting and removing HDD FPC. After replacing the HDD, be sure to format the new HDD. See "Formatting HDD" in Service Navigation. 1) How to Remove Remove the HDD Shield Case from the unit. Remove the HDD cushion from the HDD. Remove the HDD FPC from HDD using the tool.
Fig. D3
Fig. D4
27
SDR-H40P
2) How to Attach Attach the HDD FPC to the new HDD using the tool. Attach the HDD cushion to the HDD. Attach the HDD Shield Case to the unit.
Fig. D6
Fig. D7
Fig. D5
28
SDR-H40P
Fig. D10 Fig. D8
Fig. D9 Fig. D11
29
SDR-H40P
Fig. D12
Fig. D13
30
SDR-H40P
8.4.
Disassembly Procedures of Camera Lens Unit
The following flowchart describes order or steps for removing the Camera lens unit and certain printed circuit boards in order to make access to the item needing service. To reassemble the unit follow the steps in reverse order.
Fig. L1
Fig. L2
31
SDR-H40P
9 Measurements and Adjustments
9.1. EEPROM Data for spare parts of the MAIN P.C.B.
After replacing the MAIN P.C.B., be sure to achieve adjustment. As for Adjustment condition/procedure, consult the "Adjustment Manual" which is available in Adjustment software. The Adjustment software is available at "TSN Website", therefore, access to "TSN Website" at "Support Information from NWBG/VDBG-PAVC".
9.2.
9.2.1.
Service Positions
List of the extension cables
Use the following extension cables when checking or adjusting individual circuit boards except module Parts (Main P.C.B.).
32
SDR-H40P
9.2.2.
Checking and repairing individual circuit boards except module parts (Main P.C.B.)
How to use extension cables.
33
SDR-H40P
9.3.
Location for Connectors of the Main P.C.B.
34
SDR-H40P
9.4.
9.4.1.
Electrical Adjustment Procedures
Initial Guideline
The table below shows which adjustments are necessary according to the unit parts and individual parts to be replaced. Make sure to perform these adjustments shown below as necessary.
9.4.2.
Set-up manual for SD Card/Hard Disk Video Camera.
1. Installation of USB-SERIAL Driver Execute the "Setup.exe" file in "Com Mass" folder by double clicking to install the USB-SERIAL driver. 2. Set-Up a. Remove the SD card from this unit. b. To enter the PC connection (COM) mode, push the [DELETE] button, [DVD COPY] button and [JOYSTICK CONTROL UP] simultaneously for 3 seconds without connecting the USB Cable.
35
SDR-H40P
c. Connect the PC and SD Card/Hard Disk Video Camera as shown in Fig. E1 and E2.
Fig. E1
Fig. E2 Rough image of set-up connection
36
SDR-H40P
9.4.3.
Set up of PC-EVR Adjustment Program
1. Turn on the PC and install the PC-EVR Adjustment Program into the PC. 2. Execute the "khd2008.exe" file by double clicking to start up the PC-EVR Adjustment Program. The main menu will be displayed. 3. Select the appropriate model. 4. Turn on the camcorder and set to PC connection (COM) mode. Then click "Start". Note: When the camcorder does not power on, turn the power on with forced power on function. Push and hold the [MENU] and [JOYSTICK CONTROL RIGHT], then set [POWER SW] to ON until the power is turned on. Note: The adjusted data is stored in the EEPROM IC after each adjustment. 7. After adjustment, to close the software, select "Exit" in the File menu or close the window.
Fig. E2-3
Fig. E2-1
5. When the communication is complete, the dialog will appear. Click "Yes" and "Save" to save the EEPROM data.
Fig. E2-4
8. To release the PC connection (COM) mode, push the [DELETE], [DVD COPY] and [JOYSTICK CONTROL UP] simultaneously for 3 seconds with the USB Cable disconnected.
9.4.4.
Fig. E2-2
How to confirm "OneNAND-Flash ROM Error"
6. When EEPROM data has been saved, the menu will appear. To perform each adjustment, display the adjustment menu by selecting from "Camera Adjust" or "Video Adjust" and select each adjustment item.
If there is a problem with Flash ROM (IC3203), the unit does not turn the power on. (Problem: When the power SW is turned on, the power LED lights for 3 seconds and goes out. The power can not be turned on again.) If this problem occurs, check if the Flash ROM (IC3203) has a problem in the following procedure. 1. Start PC-EVR Adjustment Program. 37
SDR-H40P
Refer to "8.1.4. Set up of PC-EVR Adjustment Program" and start PC-EVR Adjustment Program. 2. Select the "Diagnosis"
Fig. E2-8
Fig. E2-5
3. Select the "Lock Info"
Fig. E2-6
4. Confirm the OneNAND-Flash ROM Error information.
Fig. E2-7
5. If "Fatal Error" is displayed, Flash ROM (IC3203) is defective. Replace Main P.C.B. Note: This error information is recorded on EEPROM. Click "Error Reset" to clear the error information after replacing Flash ROM (IC3203).
38
SDR-H40P
10 Maintenance
10.1. Cleaning Lens and LCD Panel
Do not touch the surface of the lens and LCD Panel with your hand. When cleaning the lens, use air-Blower to blow off the dust. When cleaning the LCD Panel, dampen the lens cleaning paper with lens cleaner, and the gently wipe the their surface. Note: A lens cleaning paper and lens cleaner are available at local camera shops and market place.
39
SDR-H40P
40
SDR-H40P
11 Schematic Diagrams
11.1. OVERALL SCHEMATIC DIAGRAM
LENS UNIT
CCD FLEX.
FRONT P.C.B.
MIC
AV MULTI JACK (AV OUTPUT)
SPEAKER
SD
ZOOM
OIS
IRIS
FOCUS
IC7801, IC7802 (GYRO)
IC4801 (MIC AMP)
IC3301 AVIO (D/A,A/D,AV OUT AMP)
AVIO
IC303 (V.DRIVER) USB TERMINAL
IC302 (TIMING GENERATOR, CAMERA SIGNAL PROCESSOR)
IC3001 (VIDEO SIGNAL PROCESS, AUDIO SIGNAL PROCESS, MICROCONTROLLER INTERFACE, ATAPI INTERFACE, SD CARD INTERFACE, USB INTERFACE, MEMORY INTERFACE, DAC, VCO, JPEG COMPRESSION, ETC)
IC3203 (USB HOST)
TG/AFE
VIDEO
USB HOST
HDD DRIVE UNIT
IC701 (ZOOM DRIVE, FOCUS DRIVE, IRIS DRIVE, OIS DRIVE)
LENS DRIVE
HDD G-SENSOR
IC2302 (HDD G-SENSOR) IC3203 (FLASH MEMORY) IC3202 (SDRAM) IC8001 (CONTROLLER & SIGNAL PROCESSOR)
IC6201 (RTC/POWER CONTROL)
MEMORY
IC6001 (CONTROL MICROCOMPUTER)
LCD
IC6004 (EEPROM)
POWER SUPPLY CONTROL CIRCUIT IC1001 (POWER SUPPLY) 2.7"WIDE LCD
SYSCON & SUB SYSCON MAIN P.C.B.
POWER
LCD BLACKLIGHT P.C.B.
SDR-H40,H48 OVERALL SCHEMATIC DIAGRAM
41
SDR-H40P
11.2. INTERCONNECTION SCHEMATIC DIAGRAM
W
T ZOOM O.I.S. MODE DIAL POWER LCD PLUS DVD COPY RECORDING START/STOP BATTERY CATCHER
LENS UNIT
N
JOYSTICK MENU DELETE
REAR CASE UNIT
OPERATION UNIT
B1
M
ECM(L)
ECM(R)
L
MIC UNIT
USB
TO EVR
MAIN P.C.B. FRONT P.C.B.
MAIN CONNECTION TG/AFE LENS DRIVE USB HOST SYSCON AVIO LCD HDD G-SENSOR SUB SYSCON POWER MEMORY
K
FP81 FP8102 FP8101
LCD REVERS SWITCH
VIDEO
MONITOR LCD PANEL
J
LCD OPEN SWITCH
AV MULTI
SHAFT FPC
LCD BACKLIGHT P.C.B.
I
LITHIUM BATTERY
SPEAKER
PS301 2 SP1 SP+
H
DOOR OPEN
SPEAKER UNIT
SD P.C.B.
FP6301
10
11
12
8
7
6
5
4
3
2
1
9
13
HDD DRIVE
SDR-H40,H48 INTERCONNECTION SCHEMATIC DIAGRAM
1
2
3
4
5
6
7
8
9
10
42
SDR-H40P
11.3. FRONT SCHEMATIC DIAGRAM
(FRONT P.C.B.)
:AUDIO MAIN SIGNAL PATH IN REC MODE
4.9 4.9 4.2 TO MAIN CN FP6501
G
0
2.4
2.4
2.4
TO FP41
F
(MIC AMP)
2.4
2.4
2.4
4.9
E
D
2.9 1.4 (AMP) 1.7 1.7 2.9 (AMP) 0
C
1.2
2.9 NOTE: DO NOT USE ANY PART NUMBER SHOWN ON THIS SCHEMATIC DIAGRAM FOR ORDERING. WHEN YOU ORDER A PART,PLEASE REFER TO PARTS LIST. NOTE: THE MEASUREMENT MODE OF THE DC VOLTAGE ON THIS DIAGRAM IS STOP MODE. NOTE: CIRCUIT VOLTAGE AND WAVEFORM DESCRIBED HEREIN SHALL BE REGARDED AS REFERENCE INFORMATION WHEN PROBING DEFECT POINT, BECAUSE IT MAY DIFFER FROM AN ACTUAL MEASURING VALUE DUE TO DIFFERENCE OF MEASURING INSTRUMENT AND ITS MEASURING CONDITION AND PRODUCT ITSELF.
B
(GYRO P SENSOR) 1.3 0
1.2
2.9
(GYRO Y SENSOR)
A
1.3
0
SDR-H40,H48 FRONT SCHEMATIC DIAGRAM
1
2
3
4
5
6
7
8
9
10
43
SDR-H40P
11.4. LCD BACKLIGHT SCHEMATIC DIAGRAM
(LCD BACKLIGHT P.C.B.)
:VIDEO MAIN SIGNAL PATH
H
R8148 0
TO LCD PANEL FP8102
G
TO SHAFT FPC FP8101
R8149 0
F
(AMP) 0 -5.6
R8142 68K C8120 4.7
0
E
R8144 220K
D
47K
47K
47K
0 2.9
C
2.9 0 0
0 UNR9213J (LCD DRIVE)
0 UNR9213J 0 (LCD DRIVE)
UNR9213J 0 (LCD DRIVE)
NOTE: DO NOT USE ANY PART NUMBER SHOWN ON THIS SCHEMATIC DIAGRAM FOR ORDERING. WHEN YOU ORDER A PART,PLEASE REFER TO PARTS LIST.
MONITOR LCD BACKLIGHT
MONITOR LCD BACKLIGHT
MONITOR LCD BACKLIGHT
MONITOR LCD BACKLIGHT
NOTE: THE MEASUREMENT MODE OF THE DC VOLTAGE ON THIS DIAGRAM IS STOP MODE. (LCD: ON) NOTE: CIRCUIT VOLTAGE AND WAVEFORM DESCRIBED HEREIN SHALL BE REGARDED AS REFERENCE INFORMATION WHEN PROBING DEFECT POINT, BECAUSE IT MAY DIFFER FROM AN ACTUAL MEASURING VALUE DUE TO DIFFERENCE OF MEASURING INSTRUMENT AND ITS MEASURING CONDITION AND PRODUCT ITSELF.
B
(BACKLIGHT DRIVE) (BACKLIGHT DRIVE) (BACKLIGHT DRIVE)
(BACKLIGHT ON/ OFF CONTLOL)
1.1 1.4 0 1.1 0.3
0.5
1.4 1.1 0.3
1.4 1.1 0.3
1.4 1.1 0.3
C8121 4.7
A
(BACKLIGHT DRIVE)
SDR-H40,H48 LCD BACKLIGHT SCHEMATIC DIAGRAM
1 2 3 4 5 6 7 8 9 10 11 12
44
SDR-H40P
11.5. REAR CASE SCHEMATIC DIAGRAM
(REAR CASE UNIT) "FOR REFERENCE ONLY"
11.7. HDD FPC UNIT SCHEMATIC DIAGRAM
(HDD FPC) "FOR REFERENCE ONLY"
B
TO MAIN CN BATTERY CATCHER
E
TO MAIN CN
TO HDD UNIT
TO FP11
A
SDR-H40,H48 REAR CASE UNIT SCHEMATIC DIAGRAM
D
1
2
3
4
5
11.6. SHAFT FPC SCHEMATIC DIAGRAM
(SHAFT FPC) "FOR REFERENCE ONLY"
:VIDEO MAIN SIGNAL PATH IN REC MODE
LCD REVERS TO LCD BACK LIGHT
C
TO FP21
D
TO MAIN CN
B
C
TO FP81
TO FP8101
A
SDR-H40,H48 HDD FPC SCHEMATIC DIAGRAM
B
1
2
3
4
5
A
SDR-H40,H48 SHAFT FPC SCHEMATIC DIAGRAM
LCD OPEN
1
2
3
4
5
45
SDR-H40P
11.8. CCD SCHEMATIC DIAGRAM
(CCD FPC) "FOR REFERENCE ONLY"
:VIDEO MAIN SIGNAL PATH
TO MAIN CN
C
TO FP31
B
(AMP)
A
SDR-H40,H48 CCD SCHEMATIC DIAGRAM
1
2
3
4
5
46
SDR-H40P
11.9. SIDE L UNIT SCHEMATIC DIAGRAM
(SIDE L UNIT) "FOR REFERENCE ONLY"
G
F
TO MAIN CN
E
TO FP61
D
C
B
A
SDR-H40,H48 SIDE L UNIT SCHEMATIC DIAGRAM
1
2
3
4
5
6
7
8
9
10
47
SDR-H40P
11.10. SD SCHEMATIC DIAGRAM
(SD P.C.B.)
NOTE: DO NOT USE ANY PART NUMBER SHOWN ON THIS SCHEMATIC DIAGRAM FOR ORDERING. WHEN YOU ORDER A PART,PLEASE REFER TO PARTS LIST. NOTE: THE MEASUREMENT MODE OF THE DC VOLTAGE ON THIS DIAGRAM IS STOP MODE. NOTE: CIRCUIT VOLTAGE AND WAVEFORM DESCRIBED HEREIN SHALL BE REGARDED AS REFERENCE INFORMATION WHEN PROBING DEFECT POINT, BECAUSE IT MAY DIFFER FROM AN ACTUAL MEASURING VALUE DUE TO DIFFERENCE OF MEASURING INSTRUMENT AND ITS MEASURING CONDITION AND PRODUCT ITSELF.
G
TO SPEAKER P6301
SD DOOR
F
2.9 (TEMP SENSOR)
IMPORTANT SAFETY NOTICE: COMPONENTS IDENTIFIED WITH THE MARK HAVE THE SPECIAL CHARACTERISTICS FOR SAFETY. WHEN REPLACING ANY OF THESE COMPONENTS, USE ONLY THE SAME TYPE.
MANUAL 3.0 0 BATTERY
E
TO MAIN CN FP6301
AUTO
RESET
D
3.2 3.2 TO FP51 3.2
(CARD IN :ON)
C
B
A
SDR-H40,H48 SD SCHEMATIC DIAGRAM
1
2
3
4
5
6
7
8
9
10
48
SDR-H40P
12 Printed Circuit Board
12.1. SD P.C.B.
(LSEP8444A1)
D
C
B
A
(COMPONENT SIDE)
(FOIL SIDE)
SDR-H40,H48 SD P.C.B.
1
2
3
4
5
6
7
8
9
49
SDR-H40P
12.2. FRONT P.C.B.
(LSEP8445A1)
E
D
C
B
A
(COMPONENT SIDE)
(FOIL SIDE)
SDR-H40,H48 FRONT P.C.B.
1
2
3
4
5
6
7
8
9
50
SDR-H40P
12.3. LCD BACKLIGHT P.C.B.
(LSEP8433B1)
E
D
C
B
A
(COMPONENT SIDE)
(FOIL SIDE)
SDR-H40,H48 LCD BLACKLIGHT P.C.B.
1
2
3
4
5
6
7
8
9
51
SDR-H40P
52
SDR-H40P
13 Parts and Exploded Views
13.1. Exploded Views
13.1.1. Frame & Casing Section
53
SDR-H40P
54
SDR-H40P
13.1.2. LCD Section
55
SDR-H40P
13.1.3. Camera Lens Section
56
SDR-H40P
13.1.4. Packing Parts & Accessories Section
57
SDR-H40P
13.2. Replacement Parts List
13.2.1. Frame & Casing Section Parts List
Ref. No. B107 B110 B111 B112 B113 B114 B115 B116 Part No. XQN16+BF4FN XQN16+BJ5FN XQN16+BJ5FN XQN16+BJ5FN XQN16+BJ5FN XQN16+BJ5FN XQN16+BJ5FN XQN16+BJ5FN Part Name & Description SCREW SCREW SCREW SCREW SCREW SCREW SCREW SCREW Pcs 1 1 1 1 1 1 1 1 Remarks
Ref. No. 1 1-1 1-2 2 3 5 6 B1 B2 B3 B4 B6 B7 B8 B9 B10 B11 B12 B13 B14 B15 B16 B17 B18 B19 B20 B21 B22 B23 101
Part No.
Part Name & Description FRONT P.C.B. FRONT ANGLE MIC DAMPER OPERATION U FRONT/TOP U GRIP U SIDE R CASE U SCREW SCREW SCREW SCREW SCREW SCREW SCREW SCREW SCREW SCREW SCREW SCREW SCREW SCREW SCREW SCREW SCREW SCREW SCREW SCREW SCREW SCREW MAIN P.C.B.
Pcs
Remarks
LSEP8445A1 LSMA1039 LSMG0190 LSYK2330 LSYK2350 LSYK2352 LSYK2322 XQN2+BF5FN XQN2+BF5FN XQN16+BJ4FN XQN16+BJ4FN XQN16+BF4FN XQN16+BF4FN XQN16+BF4FN XQN16+BF4FN XQN16+BF4FN XQN16+BF4FN XQN16+BF4FN XQN16+BF4FN XQN16+BF4FN XQN16+BJ5FN XQN16+BJ5FN XQN16+BJ5FN XQN16+BJ5FN XQN16+BJ5FN XQN16+BJ5FN XQN16+BJ5FN XQN16+BJ5FN XQN16+BJ5FN LSEP8443A1
1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
(RTL)
13.2.2. LCD Section Parts List
Ref. No. 201 202 203 204 205 206 207 208 209 210 211 212 213 214 215 216 [PSECI] (RTL) P,PC,PL 216 216 B201 B202 B203 B204
Part No.
Part Name & Description LCD SHAFT FPC SHAFT U SHAFT SW HOLDER SHAFT CASE A SHAFT CASE B LCD CASE B LCD SHIELD CASE PANEL HOLDER U BEF SHEET A WIDE BEF SHEET B WIDE DIFFUSION SHEET WIDE LEAD LIGHT PANEL REFLECT SHEET WIDE LCD LCD BACKLIGHT P.C.B. LCD CASE A U
Pcs
Remarks
LSEP8449A1 LSXA0946 LSMD0880 LSKM1688 LSKM1689 LSKM1690 LSSC1011 LSXY1249 LSGL1523 LSGL1524 LSGL1525 LSGL1526 LSGL1527 L5BDDXH00032 LSEP8433B1 LSYK2323
1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
(RTL) [PSECI] P,PC,PL
LSYK2324 LSYK2325 LSHD0130 XQN16+BJ4FN XQN16+BF4FN XQN16+BF4FN
LCD CASE A U LCD CASE A U SCREW SCREW SCREW SCREW
1 1 1 1 1 1
101
LSEP8443P1
MAIN P.C.B.
1
(RTL) EG,E,EB,EF, EP,GC,GN,H48G K
EG,E,EB,EF,EP ,GC,GN H48GK
102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 B101 B102 B109 B103 B104 B105 B106 B108
LSJB8451 LSMG0196 LSMG0196 LSSC1029 N3CZBRH00004 LSMA1036 LSMG0194 LSMG0194 LSJB8450 LSEP8444A1 LSJB8448 L0AA02A00083 LSYK2333 LSEK0838 LSMA1040 XQN16+BF4FN XQN16+BF4FN XQN16+BJ5FN XQN16+BF4FN XQN16+BF4FN XQN16+BF4FN XQN16+BF4FN XQN16+BJ5FN
HDD RELAY FPC HDD CUSHION HDD CUSHION HDD SHIELD CASE HDD MAIN PLATE SUB SUPPORT DAMPER SUB SUPPORT DAMPER FRONT FPC SD P.C.B. SD FPC LOUDSPEAKER SIDE L CASE U BATTERY TERMINAL U SPEAKER ANGLE SCREW SCREW SCREW SCREW SCREW SCREW SCREW SCREW
1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
13.2.3. Camera Lens Section Parts List
(RTL)
Ref. No. 401 401-1 401-2 401-3 402 403 403 404 405 B401
Part No.
Part Name & Description LENS U ZOOM MOTOR U FOCUS MOTOR U IRIS U CCD CASE CCD P.C.B. CCD P.C.B. OPTICAL LPF CCD CUSHION RUBBER SCREW
Pcs
Remarks
LSXN0053 L6HA66NB0009 L6HA66NB0010 LSEM0111 LSDW0122 LSEP8447A1 LSEP8447B1 LSFL0292 VMX3282 LSHD0136
1 1 1 1 1 1 1 1 1 1
P,PC,PL EG,E,EB,EF,EP ,GC,GN,H48GK
58
SDR-H40P
Ref. No. B402 B403 B404 B405 B406 B407
Part No. LSHD0136 XQN16+BJ4FN XQN16+BJ4FN XQN16+BJ4FN XQN16+BJ4FN XQN16+BJ4FN
Part Name & Description SCREW SCREW SCREW SCREW SCREW SCREW
Pcs 1 1 1 1 1 1
Remarks
13.2.4. Packing Parts & Accessories Section Parts List
Ref. No. 510 510 510 510 510 510 510 510 510 510 510 510 510 511 512
Part No. LSQT1341-A LSQT1342-A LSQT1343-A LSQT1344-A LSQT1345-A LSQT1348-A LSQT1346-A LSQT1347-A LSQT1349-A LSQT1351-A LSQT1350-A LSQT1353-A LSQT1354-A K2GJ2DC00020 LSPN0899
Part Name & Description O/I O/I O/I O/I O/I O/I O/I O/I O/I O/I O/I O/I O/I DC CABLE BOTTOM PAD
Pcs 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
Remarks EG EG EG,EF E E EB EP EP GC GC GC GN H48GK
Ref. No. 501
Part No.
Part Name & Description PACKING CASE
Pcs
Remarks
13.2.5. Electrical Replacement Parts List
LSPG2588
1
[PSECI] P,PC,PL
501 501 501 501 502 503 504
LSPG2592 LSPG2593 LSPG2616 LSPG2594 LSPN0886 VPF1129 DE-A51BA
PACKING CASE PACKING CASE PACKING CASE PACKING CASE PAD PROTECTION BAG POWER CHARGERS
1 1 1 1 1 1 1
EG,E,EB,EF GC,GN EP H48GK
Ref. No. B1
Part No.
Part Name & Description CONNECTOR 40P BATTERY C.CAPACITOR 1U C.CAPACITOR 10U C.CAPACITOR 6.3V 1U C.CAPACITOR 6.3V 1U C.CAPACITOR 6.3V 10U C.CAPACITOR 8200P C.CAPACITOR 0.027U C.CAPACITOR 0.027U C.CAPACITOR 0.027U C.CAPACITOR 8200P C.CAPACITOR 0.027U E.CAPACITOR 6.3V 22U C.CAPACITOR 6.3V 100U C.CAPACITOR 0.01U C.CAPACITOR 0.01U C.CAPACITOR 18P C.CAPACITOR 18P C.CAPACITOR 18P C.CAPACITOR 18P C.CAPACITOR 0.01U C.CAPACITOR 18P C.CAPACITOR 0.1U CH 16V CH 10V CH CH CH CH 16V CH 10V CH 10V CH 10V CH 16V CH 10V CH CH CH 25V CH 25V CH 50V CH 50V CH 50V CH 50V CH 25V CH 50V CH 16V
Pcs
Remarks
K1KB40A00128 ML-621S/F9DE ECJ2FB1C105K ECUM1A106KBM F1G0J105A001 F1G0J105A001 ECJ2FB0J106K ECJ0EB1C822K ECJ0EB1A273K ECJ0EB1A273K ECJ0EB1A273K ECJ0EB1C822K ECJ0EB1A273K F3F0J226A055 F3G0J107A017 ECJ1VB1E103K ECJ1VB1E103K ECJ1VC1H180J ECJ1VC1H180J ECJ1VC1H180J ECJ1VC1H180J ECJ1VB1E103K ECJ1VC1H180J ECJ1XB1C104K
1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
[PSECI] BT7001 P,PC,PL C601
504 504 505
DE-A51CA DE-A51DA K2CA2CA00029
POWER CHARGERS POWER CHARGERS AC CORD
1 1 1
EG,E,EB,EF,EP ,GC,GN H48GK [PSECI] P,PC,PL
C602 C4801 C4802 C4803 C4804 C4805 C4806 C4808 C4809 C4810 C4812 C6301 C6302 C6303 C6306 C6307 C6308
505 505 505 505 506
K2CQ2CA00006 K2CT3CA00004 K2CJ2DA00011 K2CA2CA00020 K1HA05CD0014
AC CORD AC CORD AC CORD AC CORD USB CABLE
1 1 1 1 1
EG,E,EF,EP,GC EB,GC GN H48GK [PSECI] P,PC,PL
506 507 508
K1HA05CD0016 K2KZ9CB00002 LSFT0757-S
USB CABLE AV CABLE CD-ROM
1 1 1
(EXCEPT P/PC/PL) [PSECI] SEE "NOTES" P,PC,PL
508
LSFT0758-S
CD-ROM
1
(EXCEPT P/PC/PL) SEE "NOTES" [PSECI] P,PC
509 510
LSPF0107 LSQT1337-A
POLY BAG O/I
1 1
510
LSQT1338-A
O/I
1
[PSECI] C6310 PC C6311 C6312 C6313
510
LSQT1339-A
O/I
1
[PSECI] PL
59
SDR-H40P
Ref. No. C6315 C6316 C6503 C6504 C6505 C7801 C7802 C7803 C7804 C8104 C8105 C8106 C8107 C8109 C8112 C8113 C8120 C8121
Part No. ECJ1XB1C104K F1G1A104A012 ECJ1VB1A224K F1G1A104A012 ECJ1VB1A224K F1J1A106A023 F1J1A106A023 F3F0J226A055 F3F0J226A055 ECJ1VC1H390J ECJ1VC1H390J ECJ1VC1H390J ECJ1VB1A105K ECJ2FB1A475K F1J1A2250007 ECJ1VB1A105K ECJ2FB0J475K ECJ2FB0J475K
Part Name & Pcs Description C.CAPACITOR CH 16V 1 0.1U C.CAPACITOR CH 10V 1 0.1U C.CAPACITOR CH 10V 1 0.22U C.CAPACITOR CH 10V 1 0.1U C.CAPACITOR CH 10V 1 0.22U C.CAPACITOR CH 10V 1 10U C.CAPACITOR CH 10V 1 10U E.CAPACITOR CH 1 6.3V 22U E.CAPACITOR CH 1 6.3V 22U C.CAPACITOR CH 50V 1 39P C.CAPACITOR CH 50V 1 39P C.CAPACITOR CH 50V 1 39P C.CAPACITOR CH 10V 1 1U C.CAPACITOR CH 10V 1 4.7U C.CAPACITOR CH 10V 1 2.2U C.CAPACITOR CH 10V 1 1U C.CAPACITOR CH 1 6.3V 4.7U C.CAPACITOR CH 1 6.3V 4.7U DIODE DIODE DIODE DIODE LED LED LED LED DIODE CONNECTOR CONNECTOR CONNECTOR CONNECTOR IC IC IC IC IC GYROSCOPE GYROSCOPE COIL CHIP INDUCTOR 10UH CHIP INDUCTOR 100UH CONNECTOR 2P CHIP TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR TRANSISTOR 22P 16P 22P 24P 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
Remarks
Ref. No. Q8113 Q8114 Q8115 Q8116
Part No. 2SA2174J0L UNR9213J UNR9213J UNR9213J
Part Name & Description TRANSISTOR TRANSISTORRESISTOR TRANSISTORRESISTOR TRANSISTORRESISTOR M.RESISTOR 1/10W 5.6K M.RESISTOR 1/10W 0 M.RESISTOR 1/16W 4.7K M.RESISTOR 1/16W 22K M.RESISTOR 1/16W 33K M.RESISTOR 1/16W 120K M.RESISTOR 1/16W 33K M.RESISTOR 1/10W 3.9K M.RESISTOR 1/16W 120K M.RESISTOR 1/16W 33K M.RESISTOR 1/10W 3.9K M.RESISTOR 1/10W 1.2K M.RESISTOR 1/10W 10K M.RESISTOR 1/10W 0 M.RESISTOR 1/10W 0 M.RESISTOR 1/10W 15 M.RESISTOR 1/10W 560 M.RESISTOR 1/10W 0 M.RESISTOR 1/10W 33 M.RESISTOR 1/10W 33 M.RESISTOR 1/10W 33 M.RESISTOR 1/10W 33 M.RESISTOR 1/10W 33 M.RESISTOR 1/16W 10M M.RESISTOR 1/10W 3.3M M.RESISTOR 1/16W 180K M.RESISTOR 1/16W 10K M.RESISTOR 1/16W 1K M.RESISTOR 270 M.RESISTOR 270 M.RESISTOR 270 M.RESISTOR 1/10W 27 M.RESISTOR 1/10W 27 M.RESISTOR 1/10W 27 M.RESISTOR 1/10W 27 M.RESISTOR 1/10W 100K CH CH CH CH CH CH CH CH CH CH CH CH CH CH CH CH CH CH CH CH CH CH CH CH CH CH CH CH 1/16W 1/16W 1/16W CH CH CH CH CH
Pcs 1 1 1 1
Remarks
R601 R602 R4802 R4803 R4804 R4805 R4806 R4807 R4808 R4809 R4810 R6301 R6302 R6303 R6304
ERJ3GEYJ562 ERJ6GEY0R00V ERJ2GEJ472 ERJ2GEJ223 ERJ2GEJ333 ERJ2GEJ124 ERJ2GEJ333 VRE0071E392 ERJ2GEJ124 ERJ2GEJ333 VRE0071E392 ERJ6GEYJ122V D0GB103JA057 ERJ3GEY0R00 ERJ3GEY0R00 ERJ6GEYJ150V ERJ3GEYJ561 ERJ3GEY0R00 ERJ3GEYJ330 ERJ3GEYJ330 ERJ3GEYJ330 ERJ3GEYJ330 ERJ3GEYJ330 ERJ2GEJ106X ERJ3GEYJ335 ERJ2GEJ184 ERJ2GEJ103 ERJ2GEJ102X ERA3YED271V ERA3YED271V ERA3YED271V ERJ3RED270 ERJ3RED270 ERJ3RED270 ERJ3RED270 ERJ3GEYJ104
1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
D6301 D6503 D6504 D8101 D8102 D8104 D8107 D8109 D8113 FP6301 FP6501 FP8101 FP8102 IC301 IC302 IC303 IC4801 IC6301 IC7801 IC7802 L6301 L7801 L8101
B3AAB0000137 B0ADEJ000038 B3GA00000062 MAZ80620ML B3AFB0000215 B3AFB0000215 B3AFB0000215 B3AFB0000215 MAZ80470ML K1MN22BA0196 K1MN16A00077 K1MN22BA0197 K1MN24BA0196 C0DBGFC00031 VUEALLPT008 C1AB00002039 C0ABBB000369 C0ZBZ0001479 L2ES00000016 L2ES00000017 G1C100KA0031 G1C100KA0031 G1C101KA0031
R6306 R6307 R6308 R6309 R6310 R6311 R6312 R6313 R6504 R6505 R6506 R6507 R6509 R8102 R8105
P6301 Q601 Q4801 Q6301 Q6501 Q6502 Q8101 Q8102 Q8104 Q8105 Q8112
K1KA02BA0014 2SC3931CTX 2SD2216J08 2SB09700RL B1ABCF000098 2SB1218ARL 2SC6054J0L 2SC6054J0L 2SC6054J0L 2SC6054J0L 2SA2174J0L
1 1 1 1 1 1 1 1 1 1 1
R8106 R8107 R8110 R8112 R8119 R8126
60
SDR-H40P
Ref. No. R8127 R8135 R8136 R8142 R8144 R8145 R8148 R8149 R8150 R8151 R8152
Part No. D0GB102JA057 ERA3YED822V ERJ3RBD302 ERJ3GEYJ683 ERJ3GEYJ224 ERJ3GEY0R00 ERJ3GEY0R00 ERJ3GEY0R00 D0GB473JA057 D0GB473JA057 D0GB473JA057
Part Name & Description M.RESISTOR CH 1/10W 1K M.RESISTOR CH 1/16W 8.2K SURFACE MOUNTING PRECISIO M.RESISTOR CH 1/10W 68K M.RESISTOR CH 1/10W 220K M.RESISTOR CH 1/10W 0 M.RESISTOR CH 1/10W 0 M.RESISTOR CH 1/10W 0 M.RESISTOR CH 1/10W 47K M.RESISTOR CH 1/10W 47K M.RESISTOR CH 1/10W 47K SWITCH SWITCH SWITCH SWITCH SWITCH SWITCH THERMISTOR CONNECTOR 9P
Pcs 1 1 1 1 1 1 1 1 1 1 1
Remarks
SW6301 SW6302 SW6303 SW6304 SW8201 SW8202 TH601 U6301
K0F111B00074 K0F111A00547 K0F111A00547 K0F111A00547 K0C111B00008 K0F111B00074 D4CC11030013 K1NA09E00063
1 1 1 1 1 1 1 1
61