Text preview for : TCL Chassis NX56.pdf part of TCL Service Manual chassis with UOC-TOP-64 N1 series (IC201), AN5832SA (IC701), TDA7266SA (IC601), STV8172A (IC301)
Back to : TCL Chassis NX56.part1.ra | Home
TCL SERVICE MANUAL
.9861;( $3
1 2 3 4 5 6 7 8 9 10 11 Caution Specification Alignment Procedure Block Diagram Signal Processing Introduction Schematic Diagram PCB Layout Specification of Main IC Troubleshooting Explode View Diagram BOM list (Temporal lacking ) 2 6 13 31 32 39 43 45 66 69
This manual is the latest at the time of printing, and does not include the modification which may be made after the printing, by the constant improvement of product
1
CAUTION:
Use of controls, adjustments or procedures other than those specified herein may result in hazardous radiation exposure. CA UTION: TO REDUCE THE RISK OF ELECTRICAL SHOCK, DO NOT REMOVE COVER (OR BACK). NO USER SERVICEABLE PARTS INSIDE. REFER SER VICING TO QUALIFIED SERVICE PERSONNEL.
CAUTION
RISK OF ELECTRIC SHOCK DO NOT OPEN.
The lighting flash with arrowhead symbol, with an equilateral triangle is intended to alert the user to the presence of uninsulated dangerous voltage within the products enclosure that may be of sufficient magnitude to constitute a risk of electric shock to the person. The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance.
WARNING: TO REDUCE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE.
2
IMPORTANT SAFETY INSTRUCTIONS
CAUTION:
Read all of these instructions. Save these instructions for later use. Follow all Warnings and Instructions marked on the audio equipment. 1. Read Instructions- All the safety and operating instructions should be read before the product is operated. 2. Retain Instructions- The safety and operating instructions should be retained for future reference. 3. Heed Warnings- All warnings on the product and in the operating instructions should be adhered to. 4. Follow Instructions- All operating and use instructions should be followed.
FOR YOUR PERSONAL SAFETY
1. 2. 3. 4. 5. 6. 7. 8. 9. When the power cord or plug is damaged or frayed, unplug this television set from the wall outlet and refer servicing to qualified service personnel. Do not overload wall outlets and extension cords as this can result in fire or electric shock. Do not allow anything to rest on or roll over the power cord, and do not place the TV where power cord is subject to traffic or abuse. This may result in a shock or fire hazard. Do not attempt to service this television set yourself as opening or removing covers may expose you to dangerous voltage or other hazards. Refer all servicing to qualified service personnel. Never push objects of any kind into this television set through cabinet slots as they may touch dangerous voltage points or short out parts that could result in a fire or electric shock. Never spill liquid of any kind on the television set. If the television set has been dropped or the cabinet has been damaged, unplug this television set from the wall outlet and refer servicing to qualified service personnel. If liquid has been spilled into the television set, unplug this television set from the wall outlet and refer servicing to qualified service personnel. Do not subject your television set to impact of any kind. Be particularly careful not to damage the picture tube surface. Unplug this television set from the wall outlet before cleaning. Do not use liquid cleaners or aerosol cleaners. Use a damp cloth for cleaning.
10.1. Do not place this television set on an unstable cart, stand, or table. The television set may fall, causing serious injury to a child or an adult, and serious damage to the appliance. Use only with a cart or stand recommended by the manufacturer, or sold with the television set. Wall or shelf mounting should follow the manufacturer s instructions, and should use a mounting kit approved by the manufacturer. 10.2. An appliance and cart combination should be moved with care. Quick stops, excessive force, and uneven surfaces may cause the appliance and cart combination to overturn.
3
PROTECTION AND LOCATION OF YOUR SET
11. Do not use this television set near water ... for example, near a bathtub, washbowl, kitchen sink, or laundry tub, in a wet basement, or near a swimming pool, etc. Never expose the set to rain or water. If the set has been exposed to rain or water, unplug the set from the wall outlet and refer servicing to qualified service personnel.
12. Choose a place where light (artificial or sunlight) does not shine directly on the screen. 13. Avoid dusty places, since piling up of dust inside TV chassis may cause failure of the set when high humidity persists. 14. The set has slots, or openings in the cabinet for ventilation purposes, to provide reliable operation of the receiver, to protect it from overheating. These openings must not be blocked or covered. Never cover the slots or openings with cloth or other material. Never block the bottom ventilation slots of the set by placing it on a bed, sofa, rug, etc. Never place the set near or over a radiator or heat register. Never place the set in a built-in enclosure, unless proper ventilation is provided.
PROTECTION AND LOCATION OF YOUR SET
15.1. If an outside antenna is connected to the television set, be sure the antenna system is grounded so as to provide some protection against voltage surges and built up static charges, Section 810 of the National Electrical Code, NFPA No. 70-1975, provides information with respect to proper grounding of the mast and supporting structure, grounding of the lead-in wire to an antenna discharge unit, size of grounding conductors, location of antenna discharge unit, connection to grounding electrode, and requirements for the grounding electrode.
EXAMPLE OF ANTENNA GROUNDING AS PER NATIONAL ELECTRICAL CODE INSTRUCTIONS
EXAMPLE OF ANTENNA GROUNDING AS PER NATIONAL ELECTRICAL CODE ANTENNA LEAD- IN WIRE
GROUND CLAMP ANTENNA DISCHARGE UNIT (NEC SECTION 810-20)
ELECTRIC SERVICE EQUIPMENT
GROUNDING CONDUCTORS (NEC SECTION 810-21)
GROUND CLAMPS NEC-NATIONAL ELECTRICAL CODE POWER SERVICE GROUNDING ELECTRODE SYSTEM (NEC ART 250. PART H)
15.2. Note to CATV system installer : (Only for the television set with CATV reception) This reminder is provided to call the CATV system installer s attention to Article 820-40 of the NEC that provides guidelines for proper grounding and, in particular, specifies that the cable ground shall be connected to the grounding system of the building, as close to the point of cable entry as practical. 16. An outside antenna system should not be located in the vicinity of overhead power lines or other electric lights or power circuits, or where it can fall into such power lines or circuits. When installing an outside antenna system, extreme care should be taken to keep from touching such power lines or circuits as contact with them might be fatal. For added protection for this television set during a lightning storm, or when it is left unattended and unused for long periods of time, unplug it from the wall outlet and disconnect the antenna. This will prevent damage due to lightning and power-line surges.
17.
4
OPERATION OF YOUR SET
18. This television set should be operated only from the type of power source indicated on the marking label.If you are not sure of the type of power supply at your home, consult your television dealer or local power company. For television sets designed to operate from battery power, refer to the operating instructions. If the television set does not operate normally by following the operating instructions, unplug this television set from the wall outlet and refer servicing to qualified service personnel. Adjust only those controls that are covered in the operating instructions as improper adjustment of other controls may result in damage and will often require extensive work by a qualified technician to restore the television set to normal operation. When going on a holiday : If your television set is to remain unused for a period of time, for instance, when you go on a holiday, turn the television set off and unplug the television set from the wall outlet.
19.
20.
IF THE SET DOES NOT OPERATE PROPERLY
21. If you are unable to restore normal operation by following the detailed procedure in your operating instructions, do not attempt any further adjustment. Unplug the set and call your dealer or service technician. 22. Whenever the television set is damaged or fails, or a distinct change in performance indicates a need for service, unplug the set and have it checked by a professional service technician. 23. It is normal for some TV sets to make occasional snapping or popping sounds, particularly when being turned on or off. If the snapping or popping is continuous or frequent, unplug the set and consult your dealer or service technician.
FOR SERVICE AND MODIFICATION
24. Do not use attachments not recommended by the television set manufacturer as they may cause hazards. 25. When replacement parts are required, be sure the service technician has used replacement parts specified by the manufacturer that have the same characteristics as the original part. Unauthorized substitutions may result in fire, electric shock, or other hazards. 26. Upon completion of any service or repairs to the television set, ask the service technician to perform routine safety checks to determine that the television is in safe operating condition.
5
TCL-Thomson Electronics R&D Center (Shen'Zhen Lab)
Product Functional Specification
Chassis Name Issued On Updated On
NX56 2008-1-18
Serial No. Page Version 1 of 7 1.0
TTE Corporation R&D Center (Shen'Zhen Lab)
Disclosure
Proprietary Information: These drawings and specifications are the property of TCL-Thomson Electronics and shall not be reproduced or copied or used as the basis for the manufacture or sale of apparatus or devices without the written permission of TCL-Thomson Electronics. Version Information: Version states by two Arabic Numbers, which is separated by one dot, e.g. 1.2. The first number "1" means the version of approved file, the second one "2" means the version of draft.
Chassis Name Issued On Updated On
NX-56 2008-1-18
Serial No. Page Version 2 of 7 1.0
TTE Corporation R&D Center (Shen'Zhen Lab) Revision History
Model No. Status Prepared by Checked by Released by: Revised by Checked by Released by: Revised by Checked by Released by: Revised by Checked by Released by: Date Comment
Chassis Name Issued On Updated On
NX-56 2008-1-18
Serial No. Page Version 3 of 7 1.0
Model Item Master Data -Version -Customer ID -Destination -Brand -BOM NO. -Chassis Reception -Tuning [Channels Amt.] -Tuning [Technology] -Tuning [Indication] -Frequency Bands -IF Frequency -TV Systems (Color+ Sound) -AV Systems Picture-Processing -SCAN -Wide Screen Switching -Comb filter -Picture Enhancement LTI / CTI Black Stretch Dynamic Skin Others -Picture Control [General] Brightness Sharpness Contrast Tint Color -Picture Control [Special] Smart Pictures * modes VM Color Temperature Others -Picture Noise Reduction Picture Display -CRT Type Normal Flat Pure Flat Super Flat -Deflection system 1Fh 2Fh -Tube Technology Iron AK Black Matrix Others -CRT Deflection ( * Deg.) NX-56-AP 29A41
1 EM EM 03-BA41UAE-TH32
255 PLL
Digital and Bar Full Cable
38.9MHz PAL SECAM BG DK I NTSC PAL SECAM Standard
X
X X X X X 7 modes 3 modes X
X
X
X
110 4:3 29' 5W+5W
-CRT Magnetic Field -Screen Type -Screen Size / Vis. Size Sound -Audio Power Consumption -Surround Sound
Version: 1.0
Model Item -Nicam -America Stereo (MTS,BTSC,MPS) -America SAP -Korea Stereo -Thai Bilingual -Super Woofer -AVL -Sound Control [General] Volume Mute -Sound Control [Special] Treble Bass Balance Equalizer Smart Sound * modes Others -Speakers Quantity User Interface -Menu Language -Features [General] AT Biological Clock Calendar Clock Channel Swap Channel Naming Child Lock Favorite Channel Game Hotel Mode High Sensitive Notebook On/Off Timer Preset Recall Rotation Sleep AVC -Features [Special] V-chip / CCD Teletext *Pages Others New Features Smart signal Voltage display NX-56-AP 29A41
X
X X X X X 7 modes 2X1 English/Vietnam/Thai X
X X X X
X X X X
X X X
Tuning Features -Auto Channel Program -Auto/Manual Tuning -Auto/Manual Store -Fine Tuning -Factory Mode -Service Mode Cabinet -Cabinet Name
X X X X X
Version: 1.0
Model Item -Front Cabinet Color -Middle Cabinet Color -Rear Cabinet Color -Local Controls Front Mains Switch CH+ CH- VOL+ VOLTV/AV Menu Auto Search -Local Controls Top CH+ CH- VOL+ VOLTV/AV Menu Auto Search -Indicator RC Received LED Standby LED NX-56-AP 29A41
X X X X
X X
Remote Controller -Type -Batteries Connectors Rear -SCART Full w/o Y/C -SCART Full with Y/C -SCART Single (CVBS) -Component In (YPbPr) Cinch for 50Hz -In Y/C+Cinch(CVBS+ Stereo) -In Y/C+Cinch (CVBS+ Mono) -In Cinch(CVBS+ Stereo) -In Cinch (CVBS+ Mono) -Out Cinch(CVBS+ Stereo) -Out Cinch(CVBS+ Mono) - Y,Cb,Cr input -Super Woofer -Digital Audio Out -Loudspeakers -Control Busses -Feature Slot -ITV Smart Port - Antenna in 75 Ohms (IEC Type) Connectors Front/Side -In Y/C+Cinch(CVBS+ Stereo) -In Y/C+Cinch (CVBS+ Mono) -In Cinch(CVBS+ Stereo) -In Cinch (CVBS+ Mono) -Out Headphone Mini-Jack 3.5mm Final Equipment -Packing Methods 2 Color Printing Carton Color -Documents and Manuals Instruction Book Screen Sticker Plastic Bag Warranty Card
RC166
1+2
1(follow TV) X
X
Version: 1.0
Model Item Guarantee Doc. Warning Label Approbation Label Others -Languages DFU -Indication on BACKOVER Made-in in family sheet FCC/Elect Shock Caution Label CE/Elect Shock Caution Label Warning Label Others Approbation Miscellaneous -Mains Voltage -Mains Frequency -Type Mains Cord -Power Consumption TV in ON -Power Consumption TV in Standby NX-56-AP 29A41
IEC65
100-240V 50/60Hz 75W <3W
Version: 1.0
TCL Multimedia Technology Holding CRT BU R&D Center
NX56-AP&NX56B/C/E-AP Chassis Alignment Procedure
:
:
2010-01-12
:
:
:
:
1 9 13 15 16 17
RPA& RPO
CL
Chassis Name Issued on Updated on
NX56-AP&NX56B/C/E-AP 2008-01-18 2010-01-12
Serial No. Page Version Page 1 of 18 6.0
TCL Multimedia Technology Holding CRT BU R&D Center
Disclosure Proprietary Information: These drawings and specifications are the property of TCL-Thomson Electronics and shall not be reproduced or copied or used as the basis for the manufacture or sale of apparatus or devices without the written permission of TCL-Thomson Electronics. Version Information: Version states by two Arabic Numbers, which is separated by one dot, e.g. 1.2. The first number "1" means the version of approved file, the second one "2" means the version of draft.
Chassis Name Issued on Updated on
NX56-AP&NX56B/C/E-AP 2008-01-18 2010-01-12
Serial No. Page Version Page 2 of 18 6.0
TCL Multimedia Technology Holding CRT BU R&D Center
Revision History
Model No.
Prepared by 29A41/NX56 Checked by Released by Prepared by Luo MJ Guo Guangyuan Zhou Songming Luo MJ 2008-01-18 2008-01-23 2008-01-23 2008-07-04
Status
Luo MJ
Date
2008-01-18
Comment Ver0.1 03-BA41UAE-TH32 29A41/NX56 Ver1.0 1. Updated the B+ specs accord with 21" tube. 2. Updated the description accord with the software changing. Ver2.0 1. Updated the B+ specs accord with 25" tube. 2. Updated the description accord with the software changing.
All NX56-AP chassis
Checked by Released by Prepared by
All NX56-AP chassis
Checked by
Guo Guangyuan
2008-07-04
Released by
Zhou Songming GUO HQ
2008-07-04 2009-02-09
14F1 21NCM86 29E64S All NX56-AP& NX56B-AP chassis
Prepared by Checked by Released by Prepared by Checked by Released by
Ver3.0
Zhou Songming Luo MJ 2009-02-09 2009-04-24
Ver4.0 1. Updated the description accord with the software changing. 2. Updated the chassis name. Ver5.0 1. Updated the description accord with the software changing. 2. Updated the chassis name. Ver6.0 1. Updated the description accord with the software changing. 2. Updated the chassis name.
All NX56-AP& NX56B/C/E-AP chassis All NX56-AP& NX56B/C/E-AP chassis
Prepared by Checked by Released by Prepared by Checked by Released by
LI YUAN-KANG
2009-07-15
Chen Guo Biao
2010-1-12
Chassis Name Issued on Updated on
NX56-AP&NX56B/C/E-AP 2008-01-18 2010-01-12
Serial No. Page Version Page 3 of 18 6.0
TCL Multimedia Technology Holding CRT BU R&D Center
1.1. The way to enter P-Mode
a) Method one A) Switch on the TV set. B) Press the "MENU" key on RC to show the "PICTURE" OSD menu. C) Move the cursor to "Contrast" item then press the "9", "7", "3", "5" key continuously on RC within 3 seconds then enter P-Mode. The "P" letter will appear on the left low corner of the screen when enter P-Mode. Also the "FACTORY HOTKEY" will be set to "ON (= 1)". b) Another method Press the "RECALL" key on RC to enter P-mode directly. Note: 1. This will be active only when the "FACTORY HOTKEY" had set to "ON (= 1)". 2. When the power on with "FACTORY HOTKEY" had set to "ON (= 1)", the set will enter the P-Mode automatically.
1.2. Exit the P-Mode
Press the "RECALL" or "MENU" key on RC to exit the P-Mode.
1.3. Keys' function on RC at the P-Mode
Use the RC to navigate in P-Mode: Press "0" or "AT" key for screen voltage adjustment. Press "1" to "8" and "FAV" key to select factory adjustment page. Press "9" key to switch the I2C bus off/on. Press " " or "CH+ CH-"key to select option. Press " " or "VOL+ VOL-" key to adjust or select option. Press "DISPLAY" key to display software version. Press "MENU" key to close the factory menu or return to the previous menu or exit the P-Mode. Press "RECALL" key to enter or exit the P-Mode. Note: All change in P-Mode will be saved in EEPROM automatically.
Chassis Name Issued on Updated on
NX56-AP&NX56B/C/E-AP 2008-01-18 2010-01-12
Serial No. Page Version Page 4 of 18 6.0
TCL Multimedia Technology Holding CRT BU R&D Center
1.4. The adjustment page list an RC key function on P-Mode:
RC key 0 1 2 3 4 5 6 7 8 FAV 9 DISPLAY MENU RECALL AT I2C Bus OFF/ON Software version Close menu or exit the P-Mode P-Mode hotkey Screen voltage adjustment with AKB Setup and option page select Item Screen voltage adjustment Vertical geometry Horizontal geometry White Balance Adjustment Description Adjust the VG2 voltage Vertical geometry page Horizontal geometry page White Balance page Setup and option page 4 Setup and option page 5 Setup and option page 6 Setup and option page 7 Setup and option page 8 Setup and option page 9 Press this key to enter or exit BUS OFF mode Display software version Close the factory menu or return to the previous menu or exit the P-Mode Enter or exit the P-Mode Adjust the VG2 voltage
Chassis Name Issued on Updated on
NX56-AP&NX56B/C/E-AP 2008-01-18 2010-01-12
Serial No. Page Version Page 5 of 18 6.0
TCL Multimedia Technology Holding CRT BU R&D Center
2.
Flowchart of alignment procedure
B+ adjustment
Electrical properties checking for chassis White balance Adjustment NTSC geometry adjustment Aging Adjustment of focus voltage QC checking
RF AGC adjustment
Parameter setup
Adjustment of screen voltaget
PAL geometry adjustment
Set shopping status
1) B+ Adjustment 2) RF AGC Adjustment 3) Screen & Focus adjustment 4) White balance adjustment 5) Producing parameter setup and option 6) Picture Geometry adjustment ( Vertical first) 7) Set Shopping status 8) QC
Chassis Name Issued on Updated on
NX56-AP&NX56B/C/E-AP 2008-01-18 2010-01-12
Serial No. Page Version Page 6 of 18 6.0
TCL Multimedia Technology Holding CRT BU R&D Center 3. Adjustment description
Note: Alignment should be done after 3 minutes warm up of TV.
3.1 B+ Voltages
1. All relevant connectors and modules must be connected and inserted. 2. Main voltage is at 220VAC, 50Hz. voltage range:110VAC~240VAC,50Hz 3. Connect a voltmeter to B+ (Cathode of D808 for NX56 chassis or cathode of D833 for NX56B chassis) and switch on the set. 4. Input Philips test pattern signal and standard mode. 5. Adjust VR801, it should as the value in below form B+ Voltage. Table 3.1.1: The B+ value for vary tubes CRT type (Part Number) A68ERF185X013/M (44-29RFLN-HFCA) A51ERF135X90 (44-21RFLW-HF2A) A51ERS357X440(44-21RFLM-HF4A) CRTA68AGA20X99 A59EEJ04X60 44-29OFLW-TS4A B+ Voltage 125V+/-0.5V 105V+/-0.5V 108V+/-0.5V 125V+/-0.5V 125V+/-0.5V 125V+/-0.5V 105V+/-1.0V 105V+/-1.0V 105V+/-1.0V
44-25OFLP-HF5A
A59ERF181X03 44-25RFLN-HF1A
A51CPAA01X04(44-21RFLN-IRBA/NX56C) A51AEZ90X26(44-21OFLM-CH8A/NX56C) 37SX110Y22-DC05(44-14OFLN-IR6A/NX56C)
Chassis Name Issued on Updated on
NX56-AP&NX56B/C/E-AP 2008-01-18 2010-01-12
Serial No. Page Version Page 7 of 18 6.0
TCL Multimedia Technology Holding CRT BU R&D Center 3.2 RF AGC alignment
3.2.1 Method 1 A. Connect the detector as shown below (Picture 3.2) to collector of Q101. B. Receive a grey scale signal with 70dB V amplitude. C. Enter P-Mode, press "6" key on RC to select "AGCT". D. Adjust AGCT item until the output of the detector becomes 0.8Vpp
Collector of Q101
To CRO
Picture 3.2 3.2.2 Method 2 A. Receive a grey scale signal with 60dB V amplitude. B. Enter P-Mode, press "6" key on RC to select "AGCT". C. Adjust the "AGCT" value until the hint display "AGC" just change between "0" and "1".
3.3 Screen & Focus adjustment
Note: Alignment below should be done after 15 minutes warm up of TV. 1. Input cross hatch pattern signal to RF input. 2. Enter P-Mode. 2. Press "0" key on the RC and the screen will become a horizontal line. 3. Adjust the "SCREEN" VR of the FBT until the horizontal line can just be seen barely (minimum visible intensity). 4. Press "0" key again on the RC to exit the screen voltage adjustment mode. 5. Adjust the "FCOUS" VR of the FBT until the vertical line and horizontal line becomes clear, like picture 3.3.
Picture 3.3
Chassis Name Issued on Updated on
NX56-AP&NX56B/C/E-AP 2008-01-18 2010-01-12
Serial No. Page Version Page 8 of 18 6.0
TCL Multimedia Technology Holding CRT BU R&D Center 3.4 White Balance Adjustment
1. Input a black and white pattern to RF input. 2. Enter P-Mode, press key "3" to select white balance adjustment menu. 3. Use the color analyzer to measure the black side of the screen. Adjust the value of "RC","GC" and "BC" to set the reading of the color analyzer to x=274, y=280. (11500 K). 4. Then measure the white side of the screen. Adjust the value of "RD", "GD" and "BD" to set the reading of the color analyzer to x=274, y=280. (11500 K). 5. Repeat step 3&4 until you can get the correct reading for both black and white sides.
Note:
A. The "SubBRI" and "SubCON" items are used to assistant the white balance adjustment. It is the same function as the user OSD menu "Brightness" and "Contrast" items. You can adjust these items to get the expect intensity when adjusting the white balance.
B. The "BLOR-Y", "BLOG-Y" and "BLOB-Y" items are used for the YUV white balance black level offset setup. When the TV white balance adjustment is done, connect a black and white pattern to YUV input terminal. Use the color analyzer to measure the black side of the screen. Adjust the value of the "BLOR-Y", "BLOG-Y" and
"BLOB-Y" to set the reading of the color analyzer to x=274, y=280. Table 3.4.1: The White Balance adjustment OSD menu OSD menu RC GC BC RD GD BD BLOC Default Value 32 32 32 37 32 37 8 Description R cut-off setting(BLOR) G cut-off setting(BLOG) B cut-off setting(BLOB) R drive setting(WPR) G drive setting(WPG) B drive setting(WPB) Black level offset course(BLOC) Remark Adjust to right value Adjust to right value Adjust to right value Adjust to right value Adjust to right value Adjust to right value Adjust to right value accord with the tube. Recommended value= "8" Adjust to right value accord with the tube. Recommended value= "8" Don't adjust, use default value "32" for producing Same as user "Brightness" and "Contrast" adjust Adjust to right value accord with the difference tube and lot See section 3.5 for detailed
PWL
8
Peak White Limiting Brightness of horizontal line when adjust G2 Brightness Contrast YUV white balance black level offset. Sub-Brightness
NX56-AP&NX56B/C/E-AP 2008-01-18 2010-01-12 Serial No. Page Version
BriVSD SubBRI SubCON BLOR-Y BLOG-Y BLOB-Y BRTC
Chassis Name Issued on Updated on
32 32 32 64 62 64 25
Page 9 of 18 6.0
TCL Multimedia Technology Holding CRT BU R&D Center
3.5
Sub brightness adjustment
1. Input eight steps gray signal. 2. Press key "3" to enter sub-brightness adjustment. 3. At dynamic state, adjust "BRTC" until the secondary gray bar just to be seen. (like picture 3.5.)
The 2nd gray scale
Picture 3.5
3.6
Picture Geometry adjustment
3.6.1 Vertical geometry adjustment 1. Input a PAL crosshatch pattern signal to RF input. 2. Enter P-Mode, press key "1" to select vertical geometry adjustment. (The OSD menu for this adjustment as below table 3.6.1. For NTSC signal, the "-50" will be replaced with "-60".) 3. Adjust the value of the corresponding item to make the vertical geometry of the pattern look good. 4. Apply NTSC signal to adjust these value for NTSC vertical geometry. Table 3.6.1: The vertical geometry adjustment OSD menu OSD menu VSLOPE-50 VCEN-50 VSIZE-50 VZOOM-50 VSC-50 VSCROLL-50 Default Value 32 32 32 25 32 32 Description Vertical slope(VS) Vertical shift (VSH) Vertical amplitude(VA) Vertical zoom(VX) S-correction(SC) Vertical Scroll VCS Remark Adjust to right value Adjust to right value Adjust to right value Adjust to right value Adjust to right value Adjust to right value
Note: 1. For NTSC signal, the "-50" will be replaced with "-60". 2. For NTSC signal, only the "VCEN-60" and "VSIZE-60" items need the adjustment, the other items use the same data as PAL signal.
Chassis Name Issued on Updated on NX56-AP&NX56B/C/E-AP 2008-01-18 2010-01-12 Serial No. Page Version Page 10 of 18 6.0
TCL Multimedia Technology Holding CRT BU R&D Center
3. On producing, please use the "AUTO OFFSET" (On page "2") function to easy the geometry adjustment of NTSC signal. When finished the PAL signal geometry adjustment, press "2" key to enter page "2" to select "AUTO OFFSET" item, press " " key to active the automatic offset function. Then the geometry adjustment of NTSC signal will finish automated. If the geometry of NTSC signal is look good, you don't need to adjust the geometry of NTSC signal any more. 3.6.2 Horizontal geometry adjustment 1. Input a PAL crosshatch pattern signal to RF input. 2. Enter P-Mode, press key "2" to select horizontal geometry adjustment. (The OSD menu for this adjustment as below table 3.6.2. For NTSC signal, the "-50" will be replaced with "-60".) 3. Adjust the value of the corresponding item to make the horizontal geometry of the pattern look good. 4. Apply NTSC signal to adjust these value for NTSC horizontal geometry. Table 3.6.2: The horizontal geometry adjustment OSD menu OSD menu HCEN-50 HSIZE-50 HPARA-50 HTRAP-50 HCNRT-50 HCNRB-50 HBOW-50 HPARALLEL AUTO OFFSET Default Value 32 32 32 32 32 32 32 32 0 Description Horizontal shift(HSH) EW width(EWW) EW parabola width(PW) EW trapezium(TC) EW upper corner parabola(UCP) EW lower corner parabola(LCP) Horizontal bow(HB) Horizontal parallelogram(HP) Automatic offset NTSC geometry Remark Adjust to right value Adjust to right value Adjust to right value Adjust to right value Adjust to right value Adjust to right value Adjust to right value Adjust to right value See below description for detailed
Note: 1. For NTSC signal, the "-50" will be replaced with "-60". 2. For NTSC signal, only the "HCEN-60" and "HSIZE-60" items need the adjustment, the other items use the same data as PAL signal. 3. On producing, please use the "AUTO OFFSET" (On page "2") function to easy the geometry adjustment of NTSC signal. When finished the PAL signal geometry adjustment, press "2" key to enter page "2" to select "AUTO OFFSET" item, press " " key to active the automatic offset function. Then the geometry adjustment of NTSC signal will finish automated. If now the geometry of NTSC signal is look good, it not needed to adjust the geometry of NTSC signal any more.
Chassis Name Issued on Updated on
NX56-AP&NX56B/C/E-AP 2008-01-18 2010-01-12
Serial No. Page Version Page 11 of 18 6.0
TCL Multimedia Technology Holding CRT BU R&D Center 3.7 Producing parameter setup and option
1. Enter P-Mode, press key "4" to select page "4".Set the corresponding item to require value. See below table 3.7.1 for detailed description. Table 3.7.1: Producing parameter setup and option page "4" OSD menu WARM UP STATUS SHOP INIT Default Value 0 0 Description Set aging mode Set the shopping status Crystal oscillator frequency adjustment Remark 0=Aging mode off 1=Aging mode on 0=>1= Set the shopping status Adjust this value to get the max color synchronization range. Don't adjust, use default value for producing 0="FACTORY HOTKEY" off 1="FACTORY HOTKEY" on ON=On when power on POWER ON MODE EEPROM INIT POWER LOW POWER HIGH DEFAULT SND. SYS LAST 0 101 176 DK Set the power on mode EEPROM initial Set the "Voltage display" "LOW" and "HIGH" threshold Set the default sound system when auto store STB=Standby when power on LAST=Last power off status 0=>1=Active EEPROM initial Recommended value= "16" Recommended value= "168" Set the right value according to the sales area 0= Blue background for TV and AV while no signal BLUE BACK OPT 2 Set the Background option while no signal 1=Black background for TV and AV while no signal 2=Snowy background for TV and black background for AV while no signal Recommended value= "20" Press " " or "VOL+ VOL-" key to enter a sub-menu to do the setup, and press "MENU" key the previous menu
DCXO
2
FACTORY HOTKEY
1
Set factory hotkey
BLACK BRI BRI CURVE CON CURVE COL CURVE VOL CURVE
40 >> >> >> >>
Set the black background brightness while no signal Set the brightness curve Set the contrast curve Set the colour curve Set the volume curve
Description: 1). Set the shopping status When trigger the "SHOP INIT" item form "0" to "1", the TV will be put on selling status.
Chassis Name Issued on Updated on NX56-AP&NX56B/C/E-AP 2008-01-18 2010-01-12 Serial No. Page Version Page 12 of 18 6.0
TCL Multimedia Technology Holding CRT BU R&D Center
The TV status after shopping status: A. "FACTORY HOTKEY" had set to "OFF". B. Picture set to "Standard" status. (Brightness=50, Contrast=50, Colour=50, White tone=Normal.) C. Sound set normal.(Volume=30,Balance=50.) D. 2). Set the user picture and sound curve value A. Brightness curve: OSD menu BRI0 BRI50 BRI100 Default Value 0 32 63 Description Set the minimal brightness when user Brightness=0 Set the brightness when user Brightness=50 Set the maximal brightness when user Brightness=0 Remark Set to 3 Use default value
B. Contrast curve:
OSD menu CON0 CON50 CON100
Default Value 0 32 63
Description Set the minimal contrast when user Contrast=0 Set the contrast when user Contrast=50 Set the maximal contrast when user Contrast=0
Remark Set to 3 Use default value
C. Colour curve: (For AP2 version)
OSD menu COL0 COL50 COL100
Default Value 0 40 63
Description Set the minimal colour when user Colour=0 Set the colour when user Color=50 Set the maximal colour when user Colour=0
Remark Set to 3 Use default value
C. Colour curve: (For AP1&AP3 version)
OSD menu COL0 COL50 COL100
Default Value 0 32 63
Description Set the minimal colour when user Colour=0 Set the colour when user Color=50 Set the maximal colour when user Colour=0
Remark Set to 3 Use default value
D. Volume curve:
OSD menu VOL0 VOL10 VOL30 VOL50 VOL80 VOL100
Default Value 0 38 65 71 77 83
Description Set the volume when user Volume=0 Set the volume when user Volume=10 Set the volume when user Volume=30 Set the volume when user Volume=50 Set the volume when user Volume=80 Set the volume when user Volume=100
Remark Use default value Set to 63 Set to 69 Set to 75 Set to 81
3). Set the value for "POWER LOW" and "POWER HIGH" A. Connect the main voltage at low threshold 95VAC/50Hz. B. Select item "POWER LOW".
Chassis Name Issued on Updated on NX56-AP&NX56B/C/E-AP 2008-01-18 2010-01-12 Serial No. Page Version Page 13 of 18 6.0
TCL Multimedia Technology Holding CRT BU R&D Center
C. Adjust the value until the hint display just change between "AC: NORMAL" and "AC: LOW". D. Connect the main voltage at high threshold 255VAC/50Hz. E. Select item "POWER HIGH. F. Adjust the value until the hint display just change between "AC: NORMAL" and "AC: HIGH". 2. Enter P-Mode, press key "5" to select page "5". Set the corresponding item to require value. See below table 3.7.2 for detailed description. Table 3.7.2: Producing parameter setup and option page "5" OSD menu Track. Mode VX Normal VX Compr. WBF WBR GET OFFSET ColdRC ColdGC ColdRD ColdGD WarmRC WarmGC WarmRD WarmGD Default Value 1 25 0 5 8 0 61 56 61 66 72 71 65 64 Description EHT tracking mode 4:3 mode vertical zoom 16:9 mode vertical zoom Wide blanking start Wide blanking end Get offset Cold color temperature R and G cut-off offset Cold color temperature R and G drive offset Warm temperature R and G cut-off offset Warm color temperature R and G drive offset Remark 0=EHT tracking only on vertical 1=EHT tracking on vertical and EW Don't adjust, use default Don't adjust, use default Don't adjust, use default Don't adjust, use default See below description for detailed Recommended value= "61" Recommended value= "56" Recommended value= "61" Recommended value= "66" Recommended value= "72" Recommended value= "71" Recommended value= "65" Recommended value= "64"
Description for AUTO OFFSET and GET OFFSET: The "GET OFFSET" can use to make the EEPROM copy by PE engineer. When the PAL and NTSC geometry adjustment had finished, trigger the "GET OFFSET" from "0" to "1" to store the geometry offset datum between PAL and NTSC in EEPROM. On producing, these geometry offset datum can use to easy the NTSC geometry adjustment. When finished the PAL geometry adjustment, trigger the "AUTO OFFSET" from "0" to "1", then the geometry adjustment of NTSC signal will finish automated. If now the geometry of NTSC signal is look good, it not needed to adjust the geometry of NTSC signal any more. 3. Enter P-Mode, press key "6" to select page "6". Set the corresponding item to require value. See below table 3.7.3 for detailed description. Table 3.7.3: Producing parameter setup and option page "6" OSD menu AGCT
Chassis Name Issued on Updated on
Default Value 32
Description AGC take over point
Serial No. Page Version
Remark See section "3.2 RF AGC alignment"
NX56-AP&NX56B/C/E-AP 2008-01-18 2010-01-12
Page 14 of 18 6.0
TCL Multimedia Technology Holding CRT BU R&D Center
AGC OIF IF AGCS AGNE 0 32 38.90 1 3 AGC take over point indicate IF demodulator offset IF frequency AGC speed Audio gain for detailed. Don't adjust, use default Select the IF frequency Don't adjust, use default Don't adjust, use default
4. Enter P-Mode, press key "7" to select page "7". Set the corresponding item to require value. See below table 3.7.4 for detailed description. Table 3.7.4: Producing parameter setup and option page "7" OSD menu EVG DFL XDT AKB NBL Default Value 0 0 0 0 0 Description Enable vertical guard(RGB blanking) Disable flash protection from deflection timer X-ray detection Black current stabilization Black current loop application Black current measuring lines in over scan(for vertical zoom setting <1) Set the cathode drive level RF NTSC M enable AV NTSC443 enable LNA high sensitivity enable LNA tuner select Game and calendar enable Software Dischanges enable Remark 1= RGB blanking Don't adjust, use default Don't adjust, use default 1=Disable 0= Enable 1=Disable 0= Enable Don't adjust, use default Adjust to right value accord with the tube. Recommended value= "12" 0=Disable 1= Enable 0=Disable 1= Enable 0: TCL tuner 1:Philips tuner 0=Disable 1= Enable 0=Disable(except NX56C) 1= Enable(nx56c)
OSVE
0
CL NTSCM NTSC443 LNA ENABLE LNA MODE GAME ENABLE BLACK LIGHT
10 0 0 0 0 0 0
5. Enter P-Mode, press key "8" to select page "8". Set the corresponding item to require value. See below table 3.7.5 and table 3.7.6 for detailed description. Table 3.7.5: Producing parameter setup and option page "8"(For AP2 version)
Chassis Name Issued on Updated on
NX56-AP&NX56B/C/E-AP 2008-01-18 2010-01-12
Serial No. Page Version Page 15 of 18 6.0
TCL Multimedia Technology Holding CRT BU R&D Center
OSD menu HOTEL A2 THAI PIC PRESET AV ALIGMENT SHVS ENABLE YUV ENABLE NOCOMMAND ENABLE ARABIC* RUSSIAN* FRENCH* FARSI* TUNER TYPE* Default Value 0 1 1 1 1 1 0 1 1 1 1 1 Description Hotel mode enable Thailand dual language enable Picture preset enable Rear AV terminal align(SCART Set "0") S-Video terminal enable YUV terminal enable No operation within 2 hours automatic standby enable Arabic enable Russian enable French enable Farsi enable Select tuner type AV no signal within 10 minutes automatic standby AV output source follow 0=xinfa(07-389FI5-NF3T) tuner 1=TCL tuner AV STANDB AVOUT FOLLOW 0 1 0=Disable 1=Enable 0=Follow TV 1=Follow source 0=Disable 1=Enable 0=3 x 3 1=4 x 3 0=Disable 1= Enable Remark
Table 3.7.6: Producing parameter setup and option page "8"(For AP1&AP3 version) OSD menu HOTEL A2 THAI HEALTH FLAT AC DISPLAY AV ALIGMENT AV2 ENABLE SHVS ENABLE YUV ENABLE NOCOMMAND ENABLE THAI* VIET* TUNER TYPE* Default Value 0 1 1 0 1 1 1 1 0 1 1 1 Description Hotel mode enable Thailand dual language enable Health platform TV enable AC voltage checking enable Rear AV terminal align(SCART Set "0") AV2 input enable S-Video terminal enable YUV terminal enable No operation within 2 hours automatic standby enable Thai enable Vietnamese enable Select tuner type Note 1 1=07-389FI5-NA3G 0=Disable 1=Enable 0=3 x 3 1=4 x 3 0=Disable 1= Enable Remark
Chassis Name Issued on Updated on
NX56-AP&NX56B/C/E-AP 2008-01-18 2010-01-12
Serial No. Page Version Page 16 of 18 6.0
TCL Multimedia Technology Holding CRT BU R&D Center
AV no signal within 10 minutes automatic standby AV output source follow 0=Disable 1=Enable 0=Follow TV 1=Follow source
AV STANDB
0
AVOUT FOLLOW
1
*Note: When change the Language or the tuner type, you must AC restart the TV set to make it active. Note 1 TUNER TYPE=0 07-389FI5-NF3T, 07-389FI5-NF2XG, 07-389FI5-NA2XG, 07-389FI5-SA0XG
6. Enter P-Mode, press key "FAV" to select page "9". Set the corresponding item to require value. See below table 3.7.7 for detailed description. Table 3.7.7: Producing parameter setup and option page "9" OSD menu BKS BSD Default Value 1 0 Description Black stretch enable Black Stretch depth Remark 0=Disable 1=Enable 0=15IRE 1=30IRE 0=12% AAS 0 Black area to switch off the black stretch 1=20% 2=6% 3=8% 0=1:1 RPA 0 Ratio of pre- and after shoot 1=1.5:1 2=2:1 0=1:1 RPO 2 Ratio of positive and negative peaks 1=1:1.3 3=1:1.7 4=1:0.7 0=0% SOC 1 Soft clipping level above PWL 1=5% 2=10% 3=Soft clipping off 0=off COR 0 Video peaking active range 1= between 0 and 20 IRE 2= between 0 and 40 IRE 3= between 0 and 100 IRE
Chassis Name Issued on Updated on
NX56-AP&NX56B/C/E-AP 2008-01-18 2010-01-12
Serial No. Page Version Page 17 of 18 6.0
TCL Multimedia Technology Holding CRT BU R&D Center 3.8 Screen voltage (VG2) adjustment with AKB function
1. Put the TV in AV source without input signal. 2. Enter P-Mode, press RC key "AT", there will display 3. Adjust the "SCREEN" VR of the FBT until VG2 hint display (LOW/OK/HIGH) display "OK" stably. 4. Press "MENU" return to P-Mode.
Chassis Name Issued on Updated on
NX56-AP&NX56B/C/E-AP 2008-01-18 2010-01-12
Serial No. Page Version Page 18 of 18 6.0
NX56 Chassis Signal Processing Introduction
Brief introduction
For different market requirements, our design it in two versions, one is for Latin America, we call the chassis as NX56-LA, the another one is for Asia Pacific Area, we call the chassis as NX56-AP. NX56-LA and NX56-AP adopt different UOC, The UOC for Latin America have CCD-Chip and BTSC function, so added AN5832SA to realize BTSC, but the UOC for Asia Pacific region does not have the two functions but SECAM system is necessary. NX56 Chassis not only match 21inches CRT, but also match 25 and 29inches CRT. Due to different screen sizes, maybe adopt different audio power amplifiers. The others should be the same. No matter NX56-AP what NX56-LA, they are use same main PCB board, just different peripheral components.
RF Section
Tuner Tu101 receive the radio frequency signal, after inside circuit to do signal receiving, and signal amplifying. The amplified high frequency signal accompany with the high frequency oscillation voltage oscillated by set oscillator input to the mixer. The IF picture signal and sound signal formed in mixer and output from mixer, then send to picture IF processing circuit.
VGA
(Fig. 1. Tuner section)
Small Signal Processing Section
Small signal processing section is the IF (intermediate frequency) signal across saw filter send in the pin12 and pin13 of IC201. The VIFIN signal through built-in PLL DEMOD, sound trap, video amplifier and synchronous detector processing, get the color video broadcast signal and 2nd sound IF signal. Video signal processing section is CVBS across video filter and delay line and horizontal & vertical synchronous separation circuit processing and get H-drive (pin56 of IC201)and V-drive signal (pin15/pin15 of IC201). IF sound signal across the sound-down-mixer and AM demodulator processing, send out the AVL/ SSIF OUT signal. ( Refer to Fig2 and Fig 3.)
(Fig 2. Small Signal Processing Section)
(Fig3. Block Diagram of IC201.)
Horizontal Scanning Section
The horizontal drive signal send out from pin 56 of IC201, Q401 is horizontal driving transistor, coupled by horizontal driving transformer T402 , to control the horizontal output transistor working in switch on and off situation, get good linearly and enough amplitude of saw-tooth wave current to drive horizontal deflection yoke scanning. L456 is horizontal width coil and L458 is horizontal linearly coil. D455 is damping diode, C453,C455,C457 are retrace capacitors. T401 is FBT. Pin2 of T401 is B+ voltage input, Pin 10 of T401 get 200 Volt video amplifying voltage supply for CRT board. Pin11 of T401 sends out heater voltage supply for CRT heater.
Vertical Scanning Section
Vertical scanning section adopted STV8172A vertical deflection booster, we use as differential-output driver. The vertical raw-tooth wave signal sends out from pin14/15 of IC201 VDA/VDB. The two differential signal input pin 1 and 7 of STV8172A IC301. Pin2(+14v) and Pin7(-14v) of IC301 is power supply which come from the main power transformer. Pin 6 is boost voltage, rectified by D301. C309,C301 and R305 makes up a voltage feedback network, R306 is a damping resistor. C306 is correction capacitor, R308 is current feedback resistor.
Fig 4. Vertical Scanning Processing Section
CRT Scanning Section
Q507,D501,D502 and D503 makes up a light eliminate circuit network. When the TV is playing mode, +8V voltage across R533 charge for C512, Q507 is cut off. At the right of turn off the TV, Q507 is turn-on, the current across D501, D502 and D503 send to R.G. B to discharge the electronic quickly.
Audio Power Amplifying Section
Power Supply Section
AC supply 220V/110v through filtering network and rectifying circuit and get 300Vdc voltage. LF801/LF801A and CX802 makes up a differential mode rejection, LF802 and CY801,CY802 makes up a common mode rejection network. D801-D804 is rectifying network. 300Vdc voltage supply pin3 of T801, also through R804 send to pin8 of IC801 NCP1337. Pin5 of IC801 sends out the PWM signal to control Q801 working in switch on and off situation. IC803 is optocoupler.
UOC-TOP-64 N1 series
Versatile signal processor for CRT TV applications
Rev. 0.11 -- 25 January 2007 Product data sheet
1. General description
The UOC-TOP-64 series is a very flexible concept which offers attractive solutions for 1fH TV receivers with CRTs. This new concept offers a complete range of products with the right price level to cover TV receivers from basic mono 14 inch sets up to the best featured large and/or wide screen AV-stereo TV sets. The UOC-TOP-64 concept can also be used as front-end for 2fH and LCD TV receivers. The UOC-TOP-64 concept is mounted in a SDIP64 package and is split up in the following ranges:
· AV-110 (AV-stereo) concept. It contains a video processor with many features and it
has an analog audio control circuit with balance, treble, bass and loudness control. Two different micro processor are available for this concept, one with OSD and Closed Captioning or Teletext and Closed Captioning features (UOCTOP_1PTXT version), the other with (extended) OSD features (UOCTOP_OSD version). The block diagram is given in Figure 1.
· AV-90 concept. This concept is nearly identical to the AV-110 concept. The only
difference that it does not contain an East-West and Scan Velocity Modulation (SVM) output. This concept is intended for 90× picture tubes.
· Mono-110 concept. The functional content of this concept is comparable with that of
the AV 110 concept, however, it has just stereo input switch and no audio control circuit. The block diagram is given in Figure 1.
· Mono-90 concept. This concept is intended for 90× picture tubes. The circuit has an
audio switch for mono signals but the mono inputs can also be used as a stereo input. In this range most of the video and audio processing features have been omitted. Also this concept can be supplied with one of the two micro processors (UOCTOP_1PTXT or UOCTOP_OSD version). The block diagram is given in Figure 2. The most important features of the complete IC series are given in the following feature lists. All packages are according to the ROHS legislation, which also means that these packages are lead-free. The ICs have supply voltages of 8V, 5V and 3.3V. UOC-TOP-64 is supported by a comprehensive Global TV Software Development kit to enable easy programming and fast time-to-market (see also Section 20.4 "Licenses").
NXP Semiconductors
UOC-TOP-64 N1 series
Signal processor for CRT TV
2.
Features
2.1 Analog Video Processing
2.1.1 Overview of available features (AV-110/90 and Mono-110 concept)
Multi-standard vision IF circuit with alignment-free PLL demodulator Internal (switchable) time-constant for the IF-AGC circuit Switchable group delay correction and sound trap (with switchable centre frequency) for the demodulated CVBS signal Separate Second Sound IF output or FM demodulator output without de-emphasis available, which can be used as input for an external BTSC decoder or as input for external sound band-pass filter for second language processing. Separate SSIF input available as input for the FM-PLL demodulator to demodulate FM-radio with an IF frequency of 10.7 MHz, or as input from an external sound band-pass filter for second language processing. AM demodulator without extra reference circuit The mono intercarrier sound circuit has a selective FM-PLL demodulator which can be switched to the different FM sound frequencies (4.5/5.5/6.0/6.5 MHz). The quality of this system is such that the external band-pass filters can be omitted. The FM-PLL demodulator can be set to centre frequencies of 4.72/5.74 MHz so that a second sound channel can be demodulated. In such an application it is necessary that an external bandpass filter is inserted. Audio switch circuit with 2 stereo inputs (1 stereo input can also be switched into two mono sound inputs) and a stereo output which can be used for the drive of for audio power amplifiers (with volume and tone-control) or as SCART/CINCH output. The second stereo input is only available via the combined C2/C3/C4/AUDIOIN5R pin for the right channel and via the combined CVBS4/Y4/AUDIOIN5L pin for the left channel. Video switch with 3 external CVBS inputs. All CVBS inputs can be used as Y-input for Y/C signals. However, only 1 Y/C source can be selected because the circuit has 1 chroma input. CVBS3/Y3 input available in combination with the G/Y-3 input pin. 1 CVBS output, this output can be used as monitor video output or as front-end video output or as independent selectable video output. Automatic Y/C signal detector. Integrated luminance delay line with adjustable delay time Only one reference (24.576 MHz) crystal required for the m-Controller, Teletext- and the color decoder Multi-standard color decoder with automatic search system and various "forced mode" possibilities Internal base-band delay line Indication of the Signal-to-Noise ratio of the incoming CVBS signal Linear RGB/YPBPR input. Scan Velocity Modulation output. The SVM circuit is active for all the incoming CVBS, Y/C and RGB/YPBPR signals. The SVM output is combined with the black current input of the black current stabilisation circuit. By means of a small application adaptation both functions can be operational in parallel.
© NXP B.V. 2007. All rights reserved.
Product data sheet
Rev. 0.11 -- 25 January 2007
2 of 230
NXP Semiconductors
UOC-TOP-64 N1 series
Signal processor for CRT TV
Picture improvement features with peaking (with switchable centre frequency, depeaking, variable positive/negative peak ratio, variable pre-/overshoot ratio and video dependent coring), dynamic skin tone control, gamma control and blue- and black stretching. All features are available for CVBS, Y/C and RGB/YPBPR signals The effect of the various features can de demonstrated by means of a `split screen' mode in which the features are activated in one half of the picture and switched off in the other half Switchable DC transfer ratio for the luminance signal Tint control for external RGB/YPBPR signals Contrast reduction possibility during mixed-mode of OSD and Text signals. Option to make a colored and in contrast reduced window. RGB control circuit with `Continuous Cathode Calibration', white point and black level off-set adjustment so that the color temperature of the dark and the light parts of the screen can be chosen independently. When this `Continuous Cathode Calibration' is not used, simple alignment of the cutoff level is possible. Adjustable `wide blanking' of the RGB outputs Horizontal synchronization with two control loops and alignment-free horizontal oscillator Vertical count-down circuit Vertical driver optimized for DC-coupled vertical output stages Horizontal and vertical geometry processing with horizontal parallelogram and bow correction and horizontal and vertical zoom The IC can be used as front-end for Progressive Scan or LCD TV receivers Low-power start-up of the horizontal drive circuit
2.1.2 Features of the AV-110/90 concept which are not available in the Mono-110 concept
Analog audio tone control circuit with treble, bass and loudness controls
2.1.3 Features of the AV-110 and Mono-110 concept which are not available in the AV-90 concept
Horizontal geometry processing and Scan Velocity Modulation output
2.1.4 Differences in feature list for the MONO-90 concept compared with AV-110/90 and Mono-110 concept
Audio switch circuit with 1 stereo input, which can also be switched into two mono sound inputs, a mono output for SCART/CINCH with the possibility to serve as front/monitor audio output. Stereo output (with volume and AVL) for audio power amplifiers. This stereo output can also be switched to one mono loudspeaker output and one fixed mono sound output. CVBS output, this output can only be used as monitor video output or as front-end video output. Only basic video processing. The remaining video features are peaking with coring, black stretching and gamma control. No horizontal geometry processing and Scan Velocity Modulation output.
© NXP B.V. 2007. All rights reserved.
Product data sheet
Rev. 0.11 -- 25 January 2007
3 of 230
NXP Semiconductors
UOC-TOP-64 N1 series
Signal processor for CRT TV
2.2 Micro-Controller
80C51 m-controller core standard instruction set and timing 0.9766 ms machine cycle maximum of 80 k x 8-bit late programmed ROM maximum of 3 k x 8-bit Auxiliary RAM I2C byte level bus interface. Interrupt controller for individual enable/disable with two level priority Two 16-bit Timer/Counter registers One 24-bit Timer (16-bit timer with 8-bit Pre-scaler) 16-bit Data pointer WatchDog timer Auxiliary RAM page pointer Stand-by, Idle and Power Down modes Up to 13 general-purpose I/O pins 14 bits PWM for Voltage Synthesis Tuning 8-bit A/D converter with 4 multiplexed inputs 4 PWM (6-bits) outputs for analogue control functions
2.3 Data Capture (Teletext and Closed Caption devices)
Text memory for 1 page Inventory of transmitted Teletext pages stored in the Transmitted Page Table (TPT) and Subtitle Page Table (SPT) Data Capture for US Closed Caption Data Capture for 525/625 line WST, VPS (PDC system A) and 625 line Wide Screen Signalling (WSS) bit decoding Automatic selection between 525 WST/625 WST Automatic selection between 625 WST/VPS on line 16 of VBI Real-time capture and decoding for WST Teletext in Hardware, to enable optimized m-processor throughput Automatic detection of FASTEXT transmission Real-time packet 26 engine in Hardware for processing accented, G2 and G3 characters Signal quality detector for video and WST/VPS data types Comprehensive teletext language coverage Vertical Blanking Interval (VBI) data capture of WST data
© NXP B.V. 2007. All rights reserved.
Product data sheet
Rev. 0.11 -- 25 January 2007
4 of 230
NXP Semiconductors
UOC-TOP-64 N1 series
Signal processor for CRT TV
2.4 Display
2.4.1 Features of the OSD-only devices
Up to 4 character sets with 256 characters each (size 16 pixels x 18 lines) Enhanced OSD modes 50Hz/60Hz display timing modes Serial and Parallel Display Attributes Single/Double Width and Height for characters Scrolling of display region Variable flash rate controlled by software Enhanced display features including overlining, underlining and italics Soft colors using CLUT with 4096 color palette Global selectable matrix: (12/16) By attribute selectable: 1.5x characters (18/24) Globally selectable character spacing Fringing (Shadow) selectable from N-S-E-W direction Fringe color selectable Contrast reduction of defined area with option of coloration Programmable Cursor Special Graphics Characters with two planes, allowing four colors per character
2.4.2 Features of the Teletext and Closed Caption devices
Four character sets Up to 576 characters with a size of 12 pixels x 16 lines are supported Teletext and Enhanced OSD modes 50Hz/60Hz display timing modes Serial and Parallel Display Attributes Scrolling of display region Variable flash rate controlled by software Soft colors using CLUT with 4096 color palette Global selectable matrix: (12) Features of level 1.5 WST and US Close Caption Single/Double/Quadruple Width and Height for characters 64 software redefinable On-Screen display characters G1 Mosaic graphics, Limited G3 Line drawing characters WST Character sets and Closed Caption Character set in single device Curtaining effect via software Fringing (Shadow) selectable from N-S-E-W direction Fringe color selectable Contrast reduction of defined area with option of coloration Programmable Cursor Special Graphics Characters with two planes, allowing four colors per character
© NXP B.V. 2007. All rights reserved.
Product data sheet
Rev. 0.11 -- 25 January 2007
5 of 230
NXP Semiconductors
UOC-TOP-64 N1 series
Signal processor for CRT TV
3.
Quick reference data
Quick reference data PARAMETER analogue supply voltage VSP supply current (5.0 V) digital supply VSP / analogue supply periphery supply current (3.3 V); Mono90 version supply current (3.3 V); AV110/90 and Mono110 versions audio supply voltage supply current (5.0/8.0 V); mono-90 version supply current (8.0 V); AV-110/90 and mono-110 version total power dissipation video IF amplifier sensitivity (RMS value) sound IF amplifier sensitivity (RMS value) external audio input (RMS value) external CVBS/Y input (peak-to-peak value) external chroma input voltage (burst amplitude) (peak-to-peak value) RGB inputs (peak-to-peak value) luminance input signal (peak-to-peak value) PB input signal (peak-to-peak value)[2] PR input signal (peak-to-peak value)[2] demodulated CVBS output (peak-to-peak value) sound IF intercarrier output (RMS value) demodulated AM sound output (RMS value) non-controlled audio output signals (RMS value) selected CVBS output (peak-to-peak value) tuner AGC output current range RGB output signal amplitudes (peak-to-peak value) horizontal output current vertical output current (peak-to-peak value) EW drive output current
[1]
[1]
Table 1: SYMBOL Supply VP IP VDDA IDDA IDDA VPAudio[1] IPAudio[1] IPAudio Ptot
MIN. 4.7 3.0
TYP. 5.0 160 3.3 50 70
MAX. 5.3 3.6
UNIT V mA V mA mA
4.7
8.0 0.5 10
8.4
V mA mA
1.1 75 1.0 1.0 1.0 0.3 0.7 1.0 0.7 0.7 2.0 100 250 1.0 2.0 0 1.2 10 1 1.2 1 1.3 1.4 1.0 0.8 150
W V mV V V V V V V V V mV mV V V mA V mA mA mA
Input voltages ViVIFrms) ViSSIF(rms) ViAUDIO(rms) ViCVBS(p-p) ViCHROMA(p-p) ViRGB(p-p) ViY(p-p) ViPB(p-p) ViPR(p-p) Output signals Vo(IFVO)(p-p) Vo(QSSO)(rms) Vo(AMOUT)(rms) Vo(AUDIO)(rms) Io(AGCOUT) VoRGB(p-p) IoHOUT IoVERT IoEWD Vo(CVBSO)(p-p)
The supply voltage for the analogue audio part of the mono-90 version can be 5V or 8V. For a supply voltage of 5V the maximum signal amplitudes at in and outputs are 1Vrms. For a supply voltage of 8V the maximum output signal amplitude is 2 Vrms. The AV-110/90 and Mono-110 versions need a supply voltage of 8 V. The YPBPR input signal amplitudes are based on a color bar signal with 100% saturation.
[2]
© NXP B.V. 2007. All rights reserved.
Product data sheet
Rev. 0.11 -- 25 January 2007
6 of 230
5.
Fig 1.
LS/SCART/CINCH -OUT
SCART/CINCH IN
AVL/SSIFOUT/FMDEMOUT
Product data sheet
I/Os
NXP Semiconductors
Block diagram
SECAM
L
R
AM DEMODULATOR SOUND PLL FM AM AUDIO SELECT DEEMPHASIS
SOUND-DOWNMIXER
LS AUDIO OUTPUT VOLUME/TONE**) CONTROL
AVL
IFVO/SVO/PIP CLK GENERATION PAL/SECAM/NTSC DECODER BASE-BAND DELAY LINE REF SKIN TONE SAT Y DELAY ADJ. GAMMA CONTROL CSI CSO // H/VDISPO H/V VERTICAL & EAST-WEST GEOMETRY RGB/YPRPB SWITCH BRI CON. H/VDISPI IREFRGB R/G/B VDS CORB IREFO IREF RGB CONTROL OSD/TEXT INSERT /// CONTR/BRIGHTN INS. CCC/BLACK ADJ. CIRN WHITE-P. ADJ. PEAKING SCAN VELOCITY MODULATION CVBS IN CVBSREF // I2C-BUS /// RESET CLKI // CLKO TMSEL SDA/SCL
AGCOUT
VIFIN
VISION IF/AGC/AFC PLL DEMOD. SOUND TRAP GROUP DELAY VIDEO AMP.
YSYNC U/V TINT SATURATION RGB MATRIX BLUE/BLACK-STRETCH
CVBS2/Y2
VIDEO SWITCH VIDEO IDENT.
**) The mono-110 version has only volume control and no tone control functions
Block diagram of the "AV-110/90" and "MONO-110" TV processor
-PROCESSOR / TELETEXT DECODER / OSD
Rev. 0.11 -- 25 January 2007
BCLIN
C2/C3/C4/ AUDIOIN5R
VIDEO FILTERS
CVBS4/Y4 AUDIOIN5L
H/V SYNC SEP.
H-OSC. + PLL 2nd LOOP H-SHIFT H-DRIVE
V-DRIVE EHTO H-OUT
RO/ GO/ BO/ PR Y PB B3/ PB-3
UOC-TOP-64 N1 series
BLKIN/SVM/ VGUARD
G3/ Y-3 EWD/AVL R3/ CVBS3/ PR-3/ Y3 C2/C3/C4
Signal processor for CRT TV
© NXP B.V. 2007. All rights reserved.
9 of 230
Fig 2.
LS/SCART/CINCH -OUT SCART/CINCH IN SECAM L
AVL
AVL/SSIFOUT/FMDEMOUT
Product data sheet
NXP Semiconductors
I/Os
AM DEMODULATOR SOUND PLL FM AM AUDIO SELECT DEEMPHASIS LS AUDIO OUTPUT VOLUME/AVL CONTROL
SOUND-DOWNMIXER
IFVO/SVO CLKI //
AGCOUT CLK GENERATION PAL/SECAM/NTSC DECODER BASE-BAND DELAY LINE REF // I2C-BUS RESET ///
CLKO TMSEL SDA/SCL CVBS IN CVBSREF
Block diagram of the "MONO-90" TV processor
SAT RGB MATRIX Y DELAY ADJ. BLACK-STRETCH
GAMMA CONTROL CORING
VIFIN
VISION IF/AGC/AFC PLL DEMOD. SOUND TRAP GROUP DELAY VIDEO AMP.
YSYNC SATURATION PEAKING
CVBS2/Y2
C2/C3/C4/
VIDEO SWITCH VIDEO IDENT.
-PROCESSOR / TELETEXT DECODER / OSD
Rev. 0.11 -- 25 January 2007
H/V VERTICAL RGB/YPRPB SWITCH BRI CON. RO GO BO V-DRIVE H-OUT EHTO G3/ Y-3 R3/ CVBS3/ PR-3/ Y3 C2/C3/C4 B3/ PB-3
BCLIN BLKIN/VGUARD
CVBS4/Y4
VIDEO FILTERS
CSI CSO // H/VDISPO H/VDISPI IREFRGB R/G/B VDS CORB IREFO IREF RGB CONTROL OSD/TEXT INSERT /// CONTR/BRIGHTN INS. CCC/BLACK ADJ. CIRN WHITE-P. ADJ.
H/V SYNC SEP.
UOC-TOP-64 N1 series
H-OSC. + PLL 2nd LOOP H-SHIFT H-DRIVE
Signal processor for CRT TV
© NXP B.V. 2007. All rights reserved.
10 of 230
NXP Semiconductors
UOC-TOP-64 N1 series
Signal processor for CRT TV
6. Pinning information
Table 6: SYMBOL Pinning information AV-110 Mono-110 1 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 SDIP64 DESCRIPTION AV-90 Mono-90 IF video output / selected CVBS output / PIP output IF video output / selected CVBS output 2nd supply voltage TV processor (+5 V) 8 Volt supply for audio switches IF-PLL loop filter ground 2 for TV processor decoupling sound demodulator AVL / Second sound IF output / sound demodulator output EHT/overvoltage protection input tuner AGC output reference current input vertical sawtooth capacitor IF input 2 IF input 1 vertical drive A output vertical drive B output East-West drive output / AVL capacitor AVL capacitor bandgap decoupling SECAM PLL decoupling ground 1 for TV-processor phase-1 filter phase-2 filter 1st supply voltage TV-processor (+5 V) decoupling digital supply crystal oscillator output crystal oscillator input port 1.5 port 3.3 or ADC3 input or PWM3 output port 3.2 or ADC2 input or PWM2 output port 3.1 or ADC1 input or PWM1 output port 3.0 or ADC0 input or PWM0 output port 2.1 or PWM0 output port 2.0 or Tuning PWM output supply to periphery (3.3V) port 1.7 or I2C-bus data line port 1.6 or I2C-bus clock line port 1.3 or Counter/Timer 1 input port 1.1 or Counter/Timer 0 input port 1.0 or external interrupt 1 external interrupt 0 or port 0.5 (4 mA current sinking capability for direct drive of LEDs) supply
© NXP B.V. 2007. All rights reserved.
IFVO/SVO/PIP [3] IFVO/SVO [3] VP2 VCC8V PLLIF GND2 DECSDEM AVL/SSIFOUT/SNDDEMOUT[2] EHTO AGCOUT IREF VSC VIFIN2 VIFIN1 VDRA VDRB EWD/AVL AVL DECBG SECPLL GND1 PH1LF PH2LF VP1 DECDIG XTALOUT XTALIN P1.5 P3.3/ADC3/PWM3 P3.2/ADC2/PWM2 P3.1/ADC1/PWM1 P3.0/ADC0/PWM0 P2.1/PWM0 P2.0/TPWM VDDP(3.3V) P1.7/SDA P1.6/SCL P1.3/T1 P1.1/T0 P1.0/INT1 INT0/P0.5 VDDC(3.3V)
2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40
Product data sheet
Rev. 0.11 -- 25 January 2007
11 of 230
NXP Semiconductors
UOC-TOP-64 N1 series
Signal processor for CRT TV
Table 6: SYMBOL
Pinning information AV-110 Mono-110 41 42 43 44 45 46 47 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 SDIP64 DESCRIPTION AV-90 Mono-90 41 42 43 44 45 45 46 46 41 42 43 44 ground OTP Programming Voltage supply voltage Blue output / PB output Blue output Green output / Y output Green output Red output / PR output Red output black current input / vertical guard / scan velocity modulation output black current input / vertical guard beam current limiter input 3rd B input / PB input 3rd G input / Y input / CVBS input / Y input 3rd R input / PR input / C2/3/4 input Y-output (for YUV interface) Y-input for sync separator supply voltage (5 V) ground connection horizontal output flyback input/sandcastle output audio output for audio power amplifier (right signal) or fixed audio output for mono applications audio output for audio power amplifier (left signal) or speaker output for mono applications chroma-2/3/4 input / audio 5 right input chroma-2/3/4 input audio 3 input / right stereo input CVBS2/Y2 input audio 2 input / left stereo input / sound IF input CVBS4/Y4 input / audio 5 left input CVBS4/Y4 input
GND5 VPE VDDA1(3.3V) BO/PBOUT BO GO/YOUT GO RO/PROUT RO BLKIN/VGUARD/SVM [1][6] BLKIN/VGUARD [1][6] BCLIN B3/PB3 G3/Y3/CVBS3/Y3 [1] R3/PR3/C2/C3/C4 [1] YOUT YSYNC VP3 GND3 HOUT FBISO/SANDCA AUDOUTSM2/LSR AUDOUTLSM1/LSL C2/C3/C4/AUDIOIN5R [1] C2/C3/C4 AUDIOIN3/IN1R [5] CVBS2/Y2 AUDIOIN2/IN1L/SSIF [4][5] CVBS4/Y4/AUDIOIN5L [1] CVBS4/Y4
[1] [2] [3] [4] [5] [6]
48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64
The function of these pins is dependent on some I2C-bus control bits. More details are given in Table 7. The function of this pin is selected by means of the CMB2-0 bits The function of this pin is selected by means of the SVO1-0 bits The SSIF input is selected by means of the SSIFM bit The choice between two mono inputs or one stereo input is realized by means of the bits SAS3-0 The black current input, vertical guard input and SVM output (AV-110/90 and Mono-110 versions) have been combined on this pin. For a reliable operation of the protection system and the black current stabilization system or SVM system, the end of the vertical guard protection pulse during normal operation should not overlap the measuring pulses. Therefore this pulse must end before line 14.
© NXP B.V. 2007. All rights reserved.
Product data sheet
Rev. 0.11 -- 25 January 2007
12 of 230
®
STV8172A
Vertical Deflection Booster for 3-APPTV/Monitor Applications with 75-V Flyback Generator
PRODUCT PREVIEW
Main Features
Power Amplifier Flyback Generator Stand